mpc8xx: remove KUP4X, KUP4K board support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Klaus Heydeck <heydeck@kieback-peter.de>

2 files changed, 0 insertions, 928 deletions

diff --git a/include/configs/KUP4K.h b/include/configs/KUP4K.h
deleted file mode 100644
index 7cf09d01f6..0000000000
--- a/include/configs/KUP4K.h
+++ /dev/null
@@ -1,488 +0,0 @@
-/*
-  * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- * Klaus Heydeck, Kieback & Peter GmbH & Co KG, heydeck@kieback-peter.de
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- * Derived from ../tqm8xx/tqm8xx.c
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC855		1	/* This is a MPC855 CPU		*/
-#define CONFIG_KUP4K		1	/* ...on a KUP4K module */
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		115200	/* console baudrate		*/
-#define CONFIG_BOOTDELAY	1	/* autoboot after 1 second	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS						\
-"slot_a_boot=setenv bootargs root=/dev/sda2 ip=off;"				\
- "run addhw; mw.b 400000 00 80; diskboot 400000 0:1; bootm 400000\0"		\
-"slot_b_boot=setenv bootargs root=/dev/sda2 ip=off;"				\
- "run addhw; mw.b 400000 00 80; diskboot 400000 2:1; bootm 400000\0"		\
-"nfs_boot=mw.b 400000 00 80; dhcp; run nfsargs addip addhw; bootm 400000\0"	\
-"fat_boot=mw.b 400000 00 80; fatload ide 2:1 400000 st.bin; run addhw;		\
- bootm 400000 \0"								\
-"panic_boot=echo No Bootdevice !!! reset\0"					\
-"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${rootpath}\0"		\
-"ramargs=setenv bootargs root=/dev/ram rw\0"					\
-"addip=setenv bootargs ${bootargs} ip=${ipaddr}::${gatewayip}"			\
- ":${netmask}:${hostname}:${netdev}:off\0"					\
-"addhw=setenv bootargs ${bootargs} ${mtdparts} console=${console} ${debug}	\
- hw=${hw} key1=${key1} panic=1 mem=${mem}\0"					\
-"console=ttyCPM0,115200\0"							\
-"netdev=eth0\0"									\
-"contrast=20\0"									\
-"silent=1\0"									\
-"mtdparts=" MTDPARTS_DEFAULT "\0"						\
-"load=tftp 200000 bootloader-4k.bitmap;tftp 100000 bootloader-4k.bin\0"		\
-"update=protect off 1:0-9;era 1:0-9;cp.b 100000 40000000 ${filesize};"		\
- "cp.b 200000 40050000 14000\0"
-
-#define CONFIG_BOOTCOMMAND  \
-    "run fat_boot;run slot_b_boot;run slot_a_boot;run nfs_boot;run panic_boot"
-
-#define CONFIG_PREBOOT	"setenv preboot; saveenv"
-
-#define CONFIG_MISC_INIT_R	1
-#define CONFIG_MISC_INIT_F	1
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE	/* don't allow baudrate change	*/
-
-#define	CONFIG_WATCHDOG	1		/* watchdog enabled		*/
-
-#define CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-/*
- * enable I2C and select the hardware/software driver
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
-
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL		0x00000020	/* PB 26 */
-#define PB_SDA		0x00000010	/* PB 27 */
-
-#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
-#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
-#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
-			else    immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
-			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-
-/*-----------------------------------------------------------------------
- * I2C Configuration
- */
-
-#define CONFIG_SYS_I2C_PICIO_ADDR	0x21	/* PCF8574 IO Expander */
-#define CONFIG_SYS_I2C_RTC_ADDR		0x51	/* PCF8563 RTC */
-
-/* List of I2C addresses to be verified by POST */
-
-#define CONFIG_SYS_POST_I2C_ADDRS	{CONFIG_SYS_I2C_PICIO_ADDR,	\
-					 CONFIG_SYS_I2C_RTC_ADDR,	\
-					}
-
-#define CONFIG_RTC_PCF8563		/* use Philips PCF8563 RTC	*/
-
-#define CONFIG_SYS_DISCOVER_PHY
-#define CONFIG_MII
-
-/* Define to allow the user to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_SNTP
-
-#ifdef CONFIG_POST
-    #define CONFIG_CMD_DIAG
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE	512		/* Console I/O Buffer Size	*/
-#endif
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x000400000	/* memtest works on     */
-#define CONFIG_SYS_MEMTEST_END		0x005C00000	/* 4 ... 92 MB in DRAM  */
-#define CONFIG_SYS_ALT_MEMTEST 1
-#define CONFIG_SYS_MEMTEST_SCRATCH	0x90000200	/* using latch as scratch register */
-
-#define CONFIG_SYS_LOAD_ADDR		0x400000	/* default load address */
-
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 115200 }
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET 1
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	19	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_OFFSET		0x40000 /*   Offset   of Environment Sector	*/
-#define CONFIG_ENV_SIZE		0x1000	/* Total Size of Environment Sector	*/
-#define CONFIG_ENV_SECT_SIZE	0x10000
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define MTDPARTS_DEFAULT	"mtdparts=40000000.flash:256k(u-boot),"	\
-						"64k(env),"		\
-						"128k(splash),"		\
-						"512k(etc),"		\
-						"64k(hw-info)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET	0x000F0000	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000100	/* size   of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x4B26500D		/* 'K&P<CR>' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC00)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
- */
-#define CONFIG_SYS_PLPRCR ( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF00
-#define CONFIG_SYS_SCCR	(SCCR_TBS | SCCR_EBDF01 |  \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-
-/* KUP4K use both slots, SLOT_A as "primary". */
-#define CONFIG_PCMCIA_SLOT_A 1
-
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-#define PCMCIA_SOCKETS_NO 2
-#define PCMCIA_MEM_WIN_NO 8
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
-#define CONFIG_IDE_LED		1	/* LED	 for ide supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		2
-#define CONFIG_SYS_IDE_MAXDEVICE	4
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_IDE1_OFFSET	(4 * CONFIG_SYS_PCMCIA_MEM_SIZE)
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV2  | OR_CSNT_SAM | \
-				 OR_SCY_5_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP \
-	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM \
-	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM \
-	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
-
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096	 Rows from SDRAM example configuration
- * 1000	 factor s -> ms
- *   32	 PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4	 Number of refresh cycles per period
- *   64	 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider =  98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-#if   defined(CONFIG_80MHz)
-#define CONFIG_SYS_MAMR_PTA		156
-#elif defined(CONFIG_66MHz)
-#define CONFIG_SYS_MAMR_PTA		129
-#else		/*   50 MHz */
-#define CONFIG_SYS_MAMR_PTA		 98
-#endif	/*CONFIG_??MHz */
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR 0x400
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL 0x68802114
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL 0x68904114
-
-/*
- * Chip Selects
- */
-#define CONFIG_SYS_OR0
-#define CONFIG_SYS_BR0
-
-#define CONFIG_SYS_OR1_8COL 0xFF000A00
-#define CONFIG_SYS_BR1_8COL 0x00000081
-#define CONFIG_SYS_OR2_8COL 0xFE000A00
-#define CONFIG_SYS_BR2_8COL 0x01000081
-#define CONFIG_SYS_OR3_8COL 0xFC000A00
-#define CONFIG_SYS_BR3_8COL 0x02000081
-
-#define CONFIG_SYS_OR1_9COL 0xFE000A00
-#define CONFIG_SYS_BR1_9COL 0x00000081
-#define CONFIG_SYS_OR2_9COL 0xFE000A00
-#define CONFIG_SYS_BR2_9COL 0x02000081
-#define CONFIG_SYS_OR3_9COL 0xFE000A00
-#define CONFIG_SYS_BR3_9COL 0x04000081
-
-#define CONFIG_SYS_OR4 0xFFFF8926
-#define CONFIG_SYS_BR4 0x90000401
-
-#define CONFIG_SYS_OR5 0xFFC007F0  /* EPSON: 4 MB  17 WS or externel TA */
-#define CONFIG_SYS_BR5 0x80080801  /* Start at 0x80080000 */
-
-#define LATCH_ADDR 0x90000200
-
-#define CONFIG_AUTOBOOT_KEYED		/* use key strings to stop autoboot */
-#define CONFIG_AUTOBOOT_STOP_STR	"."
-#define CONFIG_SILENT_CONSOLE		1
-#define CONFIG_SYS_DEVICE_NULLDEV	1       /* enble null device		*/
-#define CONFIG_VERSION_VARIABLE		1
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/KUP4X.h b/include/configs/KUP4X.h
deleted file mode 100644
index 47d16233a3..0000000000
--- a/include/configs/KUP4X.h
+++ /dev/null
@@ -1,440 +0,0 @@
-/*
- * (C) Copyright 2000-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- * Klaus Heydeck, Kieback & Peter GmbH & Co KG, heydeck@kieback-peter.de
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- * Derived from ../tqm8xx/tqm8xx.c
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC859T		1	/* This is a MPC859T CPU	*/
-#define CONFIG_KUP4X		1	/* ...on a KUP4X module		*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		115200	/* console baudrate		*/
-
-#define CONFIG_BOOTDELAY	1	/* autoboot after 1 second	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_SYS_8XX_FACT		8	/* Multiply by 8	*/
-#define CONFIG_SYS_8XX_XIN		16000000	/* 16 MHz in	*/
-
-
-#define MPC8XX_HZ ((CONFIG_SYS_8XX_XIN) * (CONFIG_SYS_8XX_FACT))
-
-/* should ALWAYS define this, measure_gclk in speed.c is unreliable */
-/* in general, we always know this for FADS+new ADS anyway */
-#define CONFIG_8xx_GCLK_FREQ	 MPC8XX_HZ
-
-
-#undef	CONFIG_BOOTARGS
-
-
-#define CONFIG_EXTRA_ENV_SETTINGS						\
-"slot_a_boot=setenv bootargs root=/dev/hda2 ip=off;"				\
-  "run addhw;diskboot 200000 0:1;bootm 200000\0"				\
-"usb_boot=setenv bootargs root=/dev/sda2 ip=off;				\
- run addhw; sleep 2; usb reset; usb scan; usbboot 200000 0:1;			\
- usb stop; bootm 200000\0"							\
-"nfs_boot=dhcp;run nfsargs addip addhw;bootm 200000\0"				\
-"panic_boot=echo No Bootdevice !!! reset\0"					\
-"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath}\0"	\
-"ramargs=setenv bootargs root=/dev/ram rw\0"					\
-"addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}"	\
- ":${netmask}:${hostname}:${netdev}:off\0"					\
-"addhw=setenv bootargs ${bootargs} hw=${hw} key1=${key1} panic=1\0"		\
-"netdev=eth0\0"									\
-"silent=1\0"									\
-"load=tftp 200000 bootloader-4x.bitmap;tftp 100000 bootloader-4x.bin\0"		\
-"update=protect off 1:0-5;era 1:0-5;cp.b 100000 40000000 ${filesize};"		\
- "cp.b 200000 40040000 14000\0"
-
-#define CONFIG_BOOTCOMMAND  \
-    "run usb_boot;run slot_a_boot;run nfs_boot;run panic_boot"
-
-
-#define CONFIG_MISC_INIT_R	1
-#define CONFIG_MISC_INIT_F	1
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE	/* don't allow baudrate change	*/
-
-#define	CONFIG_WATCHDOG		1	/* watchdog enabled		*/
-
-#define CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-/*
- * enable I2C and select the hardware/software driver
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
-
-#ifdef CONFIG_SYS_I2C_SOFT
-#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
-
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL		0x00000020	/* PB 26 */
-#define PB_SDA		0x00000010	/* PB 27 */
-
-#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
-#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
-#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
-			else    immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
-			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-#endif	/* CONFIG_SYS_I2C_SOFT */
-
-
-/*-----------------------------------------------------------------------
- * I2C Configuration
- */
-
-#define CONFIG_SYS_I2C_PICIO_ADDR	0x21	/* PCF8574 IO Expander	*/
-#define CONFIG_SYS_I2C_RTC_ADDR	0x51	/* PCF8563 RTC			*/
-
-
-/* List of I2C addresses to be verified by POST */
-
-#define CONFIG_SYS_POST_I2C_ADDRS	{CONFIG_SYS_I2C_PICIO_ADDR,	\
-					 CONFIG_SYS_I2C_RTC_ADDR,	\
-					}
-
-
-#define CONFIG_RTC_PCF8563		/* use Philips PCF8563 RTC	*/
-
-#define CONFIG_SYS_DISCOVER_PHY
-#define CONFIG_MII
-
-#undef CONFIG_KUP4K_LOGO
-
-/* Define to allow the user to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-
-/* POST support */
-#define CONFIG_POST		(CONFIG_SYS_POST_CPU	   | \
-				 CONFIG_SYS_POST_RTC	   | \
-				 CONFIG_SYS_POST_I2C)
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-#define CONFIG_CMD_USB
-
-#ifdef CONFIG_POST
-    #define CONFIG_CMD_DIAG
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x000400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x003C00000	/* 4 ... 60 MB in DRAM	*/
-#define CONFIG_SYS_LOAD_ADDR		0x200000	/* default load address */
-
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 115200 }
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET 1
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	19	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_OFFSET		0x40000 /*   Offset   of Environment Sector	*/
-#define CONFIG_ENV_SIZE		0x1000	/* Total Size of Environment Sector	*/
-#define CONFIG_ENV_SECT_SIZE	0x10000
-
-/* Address and size of Redundant Environment Sector	*/
-#if 0
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-#endif
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#if 1
-#define CONFIG_SYS_HWINFO_OFFSET	0x000F0000	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000100	/* size   of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x4B26500D	/* 'K&P<CR>' */
-#endif
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if 0 && defined(CONFIG_WATCHDOG)       /* KUP uses external TPS3705 WD */
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC00)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register	15-30
- *-----------------------------------------------------------------------
- * set the PLL, the low-power modes and the reset control (15-29)
- */
-#define CONFIG_SYS_PLPRCR	((CONFIG_SYS_8XX_FACT << PLPRCR_MFI_SHIFT) |	\
-				PLPRCR_SPLSS | PLPRCR_TEXPS)
-
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF00
-#define CONFIG_SYS_SCCR	(SCCR_TBS | SCCR_EBDF01 |  \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-
-/* KUP4K use both slots, SLOT_A as "primary". */
-#define CONFIG_PCMCIA_SLOT_A 1
-
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-#define PCMCIA_SOCKETS_NO 1
-#define PCMCIA_MEM_WIN_NO 8
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
-#define CONFIG_IDE_LED			1   /* LED   for ide supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1
-#define CONFIG_SYS_IDE_MAXDEVICE	2
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_IDE1_OFFSET	(4 * CONFIG_SYS_PCMCIA_MEM_SIZE)
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_2_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP \
-		(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM \
-		(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM \
-		((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
-
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-
-#define CONFIG_SYS_MPTPR 0x400
-
-/*
- * MAMR settings for SDRAM
- */
-#define CONFIG_SYS_MAMR 0x80802114
-
-
-/*
- * Chip Selects
- */
-
-#define CONFIG_SYS_OR4 0xFFFF8926
-#define CONFIG_SYS_BR4 0x90000401
-
-#define LATCH_ADDR 0x90000200
-
-#define CONFIG_AUTOBOOT_KEYED		/* use key strings to stop autoboot	*/
-
-#define CONFIG_AUTOBOOT_STOP_STR	"."	/* easy to stop for now		*/
-#define CONFIG_SILENT_CONSOLE	1
-
-#define CONFIG_USB_STORAGE	1
-#define CONFIG_USB_SL811HS	1
-
-#endif	/* __CONFIG_H */