diff options
| author | Stefano Babic <sbabic@denx.de> | 2014-03-05 12:51:26 +0100 |
|---|---|---|
| committer | Stefano Babic <sbabic@denx.de> | 2014-03-05 12:51:26 +0100 |
| commit | 1ad6364eeb4f578e423081d1748e8a3fdf1ab01d (patch) | |
| tree | f55731737edf1cfd653b21f2ff9d387e6c53ae24 /include/configs | |
| parent | 335143c76612a0ae26eef8abeda77641d4f63b50 (diff) | |
| parent | cc07294bc704694ae33db75b25ac557e5917a83f (diff) | |
| download | talos-obmc-uboot-1ad6364eeb4f578e423081d1748e8a3fdf1ab01d.tar.gz talos-obmc-uboot-1ad6364eeb4f578e423081d1748e8a3fdf1ab01d.zip | |
Merge branch 'master' of git://git.denx.de/u-boot-arm
Diffstat (limited to 'include/configs')
107 files changed, 2267 insertions, 1514 deletions
diff --git a/include/configs/M54418TWR.h b/include/configs/M54418TWR.h index de063b70d6..3d7dc1fb2d 100644 --- a/include/configs/M54418TWR.h +++ b/include/configs/M54418TWR.h @@ -77,7 +77,6 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE #define CONFIG_SYS_NAND_SELECT_DEVICE -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif /* Network configuration */ @@ -268,10 +267,8 @@ /* End of used area in internal SRAM */ #define CONFIG_SYS_INIT_RAM_SIZE 0x10000 #define CONFIG_SYS_INIT_RAM_CTRL 0x221 -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 256 #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - \ - CONFIG_SYS_GBL_DATA_SIZE) - 32) + GENERATED_GBL_DATA_SIZE) - 32) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32) diff --git a/include/configs/MERGERBOX.h b/include/configs/MERGERBOX.h index 3dcea0b595..930699ba6d 100644 --- a/include/configs/MERGERBOX.h +++ b/include/configs/MERGERBOX.h @@ -121,9 +121,8 @@ #define CONFIG_SYS_INIT_RAM_LOCK 1 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\ - CONFIG_SYS_GBL_DATA_SIZE) + GENERATED_GBL_DATA_SIZE) /* * Local Bus Configuration & Clock Setup diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h index 57bf04ff81..faa5495cb4 100644 --- a/include/configs/MPC8536DS.h +++ b/include/configs/MPC8536DS.h @@ -24,7 +24,7 @@ #define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */ #else -#define CONFIG_SYS_LDSCRIPT $(TOPDIR)/$(CPUDIR)/u-boot-nand.lds +#define CONFIG_SYS_LDSCRIPT $(CPUDIR)/u-boot-nand.lds #define CONFIG_SYS_TEXT_BASE 0xf8f82000 #endif /* CONFIG_NAND_SPL */ #endif @@ -42,7 +42,7 @@ #endif #ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xeff80000 +#define CONFIG_SYS_TEXT_BASE 0xeff40000 #endif #ifndef CONFIG_RESET_VECTOR_ADDRESS @@ -326,7 +326,7 @@ /* NAND boot: 4K NAND loader config */ #define CONFIG_SYS_NAND_SPL_SIZE 0x1000 -#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000) +#define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) - 0x2000) #define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR) #define CONFIG_SYS_NAND_U_BOOT_START \ (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE) @@ -626,7 +626,7 @@ #if defined(CONFIG_RAMBOOT_NAND) #define CONFIG_ENV_IS_IN_NAND 1 #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) +#define CONFIG_ENV_OFFSET ((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) #define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) #elif defined(CONFIG_RAMBOOT_SPIFLASH) #define CONFIG_ENV_IS_IN_SPI_FLASH @@ -649,11 +649,7 @@ #endif #else #define CONFIG_ENV_IS_IN_FLASH 1 - #if CONFIG_SYS_MONITOR_BASE > 0xfff80000 - #define CONFIG_ENV_ADDR 0xfff80000 - #else #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) - #endif #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ #endif diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h index 33cadb93dd..58b9c26e93 100644 --- a/include/configs/MPC8569MDS.h +++ b/include/configs/MPC8569MDS.h @@ -56,7 +56,7 @@ extern unsigned long get_clock_freq(void); #define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */ #else -#define CONFIG_SYS_LDSCRIPT $(TOPDIR)/$(CPUDIR)/u-boot-nand.lds +#define CONFIG_SYS_LDSCRIPT $(CPUDIR)/u-boot-nand.lds #define CONFIG_SYS_TEXT_BASE 0xf8f82000 #endif #endif diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index f457719bf4..7b63945888 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -24,7 +24,7 @@ #define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */ #else -#define CONFIG_SYS_LDSCRIPT $(TOPDIR)/$(CPUDIR)/u-boot-nand.lds +#define CONFIG_SYS_LDSCRIPT $(CPUDIR)/u-boot-nand.lds #define CONFIG_SYS_TEXT_BASE 0xf8f82000 #endif /* CONFIG_NAND_SPL */ #endif diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h index f82fbca77c..eabfc85f0f 100644 --- a/include/configs/P1010RDB.h +++ b/include/configs/P1010RDB.h @@ -21,19 +21,75 @@ #define CONFIG_NAND_FSL_IFC #ifdef CONFIG_SDCARD -#define CONFIG_RAMBOOT_SDCARD -#define CONFIG_SYS_TEXT_BASE 0x11000000 -#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc +#define CONFIG_SPL +#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT +#define CONFIG_SPL_DRIVERS_MISC_SUPPORT +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SPL_MMC_MINIMAL +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_FSL_LAW /* Use common FSL init code */ +#define CONFIG_SYS_TEXT_BASE 0x11001000 +#define CONFIG_SPL_TEXT_BASE 0xD0001000 +#define CONFIG_SPL_PAD_TO 0x18000 +#define CONFIG_SPL_MAX_SIZE (96 * 1024) +#define CONFIG_SYS_MMC_U_BOOT_SIZE (512 << 10) +#define CONFIG_SYS_MMC_U_BOOT_DST (0x11000000) +#define CONFIG_SYS_MMC_U_BOOT_START (0x11000000) +#define CONFIG_SYS_MMC_U_BOOT_OFFS (96 << 10) +#define CONFIG_SYS_MPC85XX_NO_RESETVEC +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" +#define CONFIG_SPL_MMC_BOOT +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SPL_COMMON_INIT_DDR +#endif #endif #ifdef CONFIG_SPIFLASH +#ifdef CONFIG_SECURE_BOOT #define CONFIG_RAMBOOT_SPIFLASH #define CONFIG_SYS_TEXT_BASE 0x11000000 -#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc +#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc +#else +#define CONFIG_SPL +#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT +#define CONFIG_SPL_DRIVERS_MISC_SUPPORT +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_FLASH_MINIMAL +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_FSL_LAW /* Use common FSL init code */ +#define CONFIG_SYS_TEXT_BASE 0x11001000 +#define CONFIG_SPL_TEXT_BASE 0xD0001000 +#define CONFIG_SPL_PAD_TO 0x18000 +#define CONFIG_SPL_MAX_SIZE (96 * 1024) +#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (512 << 10) +#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x11000000) +#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x11000000) +#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (96 << 10) +#define CONFIG_SYS_MPC85XX_NO_RESETVEC +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" +#define CONFIG_SPL_SPI_BOOT +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SPL_COMMON_INIT_DDR +#endif +#endif #endif #ifdef CONFIG_NAND #define CONFIG_SPL +#ifdef CONFIG_SECURE_BOOT #define CONFIG_SPL_INIT_MINIMAL #define CONFIG_SPL_SERIAL_SUPPORT #define CONFIG_SPL_NAND_SUPPORT @@ -51,8 +107,48 @@ #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" +#else +#define CONFIG_TPL +#ifdef CONFIG_TPL_BUILD +#define CONFIG_SPL_NAND_BOOT +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_NAND_INIT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_DRIVERS_MISC_SUPPORT +#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT +#define CONFIG_SPL_COMMON_INIT_DDR +#define CONFIG_SPL_MAX_SIZE (128 << 10) +#define CONFIG_SPL_TEXT_BASE 0xD0001000 +#define CONFIG_SYS_MPC85XX_NO_RESETVEC +#define CONFIG_SYS_NAND_U_BOOT_SIZE (576 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000) +#define CONFIG_SYS_NAND_U_BOOT_START (0x11000000) +#define CONFIG_SYS_NAND_U_BOOT_OFFS ((128 + 128) << 10) +#elif defined(CONFIG_SPL_BUILD) +#define CONFIG_SPL_INIT_MINIMAL +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_MINIMAL +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_TEXT_BASE 0xff800000 +#define CONFIG_SPL_MAX_SIZE 8192 +#define CONFIG_SYS_NAND_U_BOOT_SIZE (128 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST 0xD0000000 +#define CONFIG_SYS_NAND_U_BOOT_START 0xD0000000 +#define CONFIG_SYS_NAND_U_BOOT_OFFS (128 << 10) +#endif +#define CONFIG_SPL_PAD_TO 0x20000 +#define CONFIG_TPL_PAD_TO 0x20000 +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" +#define CONFIG_SYS_TEXT_BASE 0x11001000 +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" +#endif #endif - #ifdef CONFIG_NAND_SECBOOT /* NAND Boot */ #define CONFIG_RAMBOOT_NAND @@ -473,6 +569,43 @@ extern unsigned long get_sdram_size(void); #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/ #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/ +/* + * Config the L2 Cache as L2 SRAM + */ +#if defined(CONFIG_SPL_BUILD) +#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH) +#define CONFIG_SYS_INIT_L2_ADDR 0xD0000000 +#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_L2_SIZE (256 << 10) +#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) +#define CONFIG_SPL_RELOC_TEXT_BASE 0xD0001000 +#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 112 * 1024) +#define CONFIG_SPL_RELOC_STACK_SIZE (16 << 10) +#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 128 * 1024) +#define CONFIG_SPL_RELOC_MALLOC_SIZE (128 << 10) +#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 96 * 1024) +#elif defined(CONFIG_NAND) +#ifdef CONFIG_TPL_BUILD +#define CONFIG_SYS_INIT_L2_ADDR 0xD0000000 +#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_L2_SIZE (256 << 10) +#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) +#define CONFIG_SPL_RELOC_TEXT_BASE 0xD0001000 +#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 192 * 1024) +#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 208 * 1024) +#define CONFIG_SPL_RELOC_MALLOC_SIZE (48 << 10) +#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 176 * 1024) +#else +#define CONFIG_SYS_INIT_L2_ADDR 0xD0000000 +#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_L2_SIZE (256 << 10) +#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) +#define CONFIG_SPL_RELOC_TEXT_BASE (CONFIG_SYS_INIT_L2_END - 0x3000) +#define CONFIG_SPL_RELOC_STACK ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) +#endif +#endif +#endif + /* Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO @@ -480,7 +613,7 @@ extern unsigned long get_sdram_size(void); #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#ifdef CONFIG_SPL_BUILD +#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL) #define CONFIG_NS16550_MIN_FUNCTIONS #endif @@ -637,12 +770,12 @@ extern unsigned long get_sdram_size(void); /* * Environment */ -#if defined(CONFIG_RAMBOOT_SDCARD) +#if defined(CONFIG_SDCARD) #define CONFIG_ENV_IS_IN_MMC #define CONFIG_FSL_FIXED_MMC_LOCATION #define CONFIG_SYS_MMC_ENV_DEV 0 #define CONFIG_ENV_SIZE 0x2000 -#elif defined(CONFIG_RAMBOOT_SPIFLASH) +#elif defined(CONFIG_SPIFLASH) #define CONFIG_ENV_IS_IN_SPI_FLASH #define CONFIG_ENV_SPI_BUS 0 #define CONFIG_ENV_SPI_CS 0 @@ -653,6 +786,10 @@ extern unsigned long get_sdram_size(void); #define CONFIG_ENV_SIZE 0x2000 #elif defined(CONFIG_NAND) #define CONFIG_ENV_IS_IN_NAND +#ifdef CONFIG_TPL_BUILD +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10)) +#else #if defined(CONFIG_P1010RDB_PA) #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE #define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) /* 3*16=48K for env */ @@ -660,7 +797,8 @@ extern unsigned long get_sdram_size(void); #define CONFIG_ENV_SIZE (16 * 1024) #define CONFIG_ENV_RANGE (32 * CONFIG_ENV_SIZE) /* new block size 512K */ #endif -#define CONFIG_ENV_OFFSET ((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) +#endif +#define CONFIG_ENV_OFFSET (1024 * 1024) #elif defined(CONFIG_SYS_RAMBOOT) #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h index 6255b0ae4e..139d4fed25 100644 --- a/include/configs/P1022DS.h +++ b/include/configs/P1022DS.h @@ -30,12 +30,12 @@ #define CONFIG_FSL_LAW /* Use common FSL init code */ #define CONFIG_SYS_TEXT_BASE 0x11001000 #define CONFIG_SPL_TEXT_BASE 0xf8f81000 -#define CONFIG_SPL_PAD_TO 0x18000 -#define CONFIG_SPL_MAX_SIZE (96 * 1024) +#define CONFIG_SPL_PAD_TO 0x20000 +#define CONFIG_SPL_MAX_SIZE (128 * 1024) #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) #define CONFIG_SYS_MMC_U_BOOT_DST (0x11000000) #define CONFIG_SYS_MMC_U_BOOT_START (0x11000000) -#define CONFIG_SYS_MMC_U_BOOT_OFFS (96 << 10) +#define CONFIG_SYS_MMC_U_BOOT_OFFS (128 << 10) #define CONFIG_SYS_MPC85XX_NO_RESETVEC #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" #define CONFIG_SPL_MMC_BOOT @@ -60,12 +60,12 @@ #define CONFIG_FSL_LAW /* Use common FSL init code */ #define CONFIG_SYS_TEXT_BASE 0x11001000 #define CONFIG_SPL_TEXT_BASE 0xf8f81000 -#define CONFIG_SPL_PAD_TO 0x18000 -#define CONFIG_SPL_MAX_SIZE (96 * 1024) +#define CONFIG_SPL_PAD_TO 0x20000 +#define CONFIG_SPL_MAX_SIZE (128 * 1024) #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x11000000) #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x11000000) -#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (96 << 10) +#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (128 << 10) #define CONFIG_SYS_MPC85XX_NO_RESETVEC #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" #define CONFIG_SPL_SPI_BOOT @@ -365,10 +365,10 @@ #define CONFIG_SYS_L2_SIZE (256 << 10) #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) #define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000 -#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 128 * 1024) +#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 116 * 1024) #define CONFIG_SPL_RELOC_STACK_SIZE (32 << 10) -#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 160 * 1024) -#define CONFIG_SPL_RELOC_MALLOC_SIZE (96 << 10) +#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 148 * 1024) +#define CONFIG_SPL_RELOC_MALLOC_SIZE (108 << 10) #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 112 * 1024) #elif defined(CONFIG_NAND) #ifdef CONFIG_TPL_BUILD diff --git a/include/configs/P1023RDS.h b/include/configs/P1023RDS.h index b51354525a..2ffa3546de 100644 --- a/include/configs/P1023RDS.h +++ b/include/configs/P1023RDS.h @@ -26,7 +26,7 @@ #ifdef CONFIG_NAND_SPL #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */ #else -#define CONFIG_SYS_LDSCRIPT $(TOPDIR)/$(CPUDIR)/u-boot-nand.lds +#define CONFIG_SYS_LDSCRIPT $(CPUDIR)/u-boot-nand.lds #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ #endif /* CONFIG_NAND_SPL */ #endif @@ -194,9 +194,8 @@ extern unsigned long get_clock_freq(void); #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ #define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) + (CONFIG_SYS_INIT_RAM_END - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h index 32ed0c2714..2ffaf5c0d9 100644 --- a/include/configs/P1_P2_RDB.h +++ b/include/configs/P1_P2_RDB.h @@ -38,7 +38,7 @@ #define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */ #else -#define CONFIG_SYS_LDSCRIPT $(TOPDIR)/$(CPUDIR)/u-boot-nand.lds +#define CONFIG_SYS_LDSCRIPT $(CPUDIR)/u-boot-nand.lds #define CONFIG_SYS_TEXT_BASE 0xf8f82000 #endif /* CONFIG_NAND_SPL */ #endif diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h index 8234a828dd..da6e76002e 100644 --- a/include/configs/T1040QDS.h +++ b/include/configs/T1040QDS.h @@ -611,9 +611,8 @@ unsigned long get_board_ddr_clk(void); #endif #ifdef CONFIG_FMAN_ENET -#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x10 -#define CONFIG_SYS_FM1_DTSEC6_PHY_ADDR 0x11 -#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 4 +#define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR 0x01 +#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x02 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d @@ -670,7 +669,6 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/ /* * For booting Linux, the board info and command line data diff --git a/include/configs/T1040RDB.h b/include/configs/T1040RDB.h index 5e988c254c..fd010c057c 100644 --- a/include/configs/T1040RDB.h +++ b/include/configs/T1040RDB.h @@ -79,10 +79,6 @@ #if defined(CONFIG_SPIFLASH) #define CONFIG_SYS_EXTRA_ENV_RELOC #define CONFIG_ENV_IS_IN_SPI_FLASH -#define CONFIG_ENV_SPI_BUS 0 -#define CONFIG_ENV_SPI_CS 0 -#define CONFIG_ENV_SPI_MAX_HZ 10000000 -#define CONFIG_ENV_SPI_MODE 0 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ #define CONFIG_ENV_SECT_SIZE 0x10000 @@ -202,6 +198,7 @@ /* CPLD on IFC */ #define CONFIG_SYS_CPLD_BASE 0xffdf0000 #define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) +#define CONFIG_SYS_CSPR2_EXT (0xf) #define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \ | CSPR_PORT_SIZE_8 \ | CSPR_MSEL_GPCM \ @@ -386,6 +383,10 @@ #define CONFIG_CMD_SF #define CONFIG_SF_DEFAULT_SPEED 10000000 #define CONFIG_SF_DEFAULT_MODE 0 +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 10000000 +#define CONFIG_ENV_SPI_MODE 0 /* * General PCI @@ -543,13 +544,12 @@ #endif #ifdef CONFIG_FMAN_ENET -#define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c -#define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d -#define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e -#define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f +#define CONFIG_SYS_SGMII1_PHY_ADDR 0x03 +#define CONFIG_SYS_RGMII1_PHY_ADDR 0x01 +#define CONFIG_SYS_RGMII2_PHY_ADDR 0x02 #define CONFIG_MII /* MII PHY management */ -#define CONFIG_ETHPRIME "FM1@DTSEC1" +#define CONFIG_ETHPRIME "FM1@DTSEC4" #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ #endif @@ -596,7 +596,6 @@ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/ /* * For booting Linux, the board info and command line data @@ -627,9 +626,9 @@ #define __USB_PHY_TYPE utmi #define CONFIG_EXTRA_ENV_SETTINGS \ - "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ - "bank_intlv=cs0_cs1;" \ - "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ + "hwconfig=fsl_ddr:bank_intlv=cs0_cs1;" \ + "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\ + "usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ "netdev=eth0\0" \ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ diff --git a/include/configs/T1042RDB_PI.h b/include/configs/T1042RDB_PI.h index aafa8139b1..6d07805ffd 100644 --- a/include/configs/T1042RDB_PI.h +++ b/include/configs/T1042RDB_PI.h @@ -79,10 +79,6 @@ #if defined(CONFIG_SPIFLASH) #define CONFIG_SYS_EXTRA_ENV_RELOC #define CONFIG_ENV_IS_IN_SPI_FLASH -#define CONFIG_ENV_SPI_BUS 0 -#define CONFIG_ENV_SPI_CS 0 -#define CONFIG_ENV_SPI_MAX_HZ 10000000 -#define CONFIG_ENV_SPI_MODE 0 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ #define CONFIG_ENV_SECT_SIZE 0x10000 @@ -202,6 +198,7 @@ /* CPLD on IFC */ #define CONFIG_SYS_CPLD_BASE 0xffdf0000 #define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) +#define CONFIG_SYS_CSPR2_EXT (0xf) #define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \ | CSPR_PORT_SIZE_8 \ | CSPR_MSEL_GPCM \ @@ -394,6 +391,10 @@ #define CONFIG_CMD_SF #define CONFIG_SF_DEFAULT_SPEED 10000000 #define CONFIG_SF_DEFAULT_MODE 0 +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 10000000 +#define CONFIG_ENV_SPI_MODE 0 /* * General PCI @@ -551,8 +552,11 @@ #endif #ifdef CONFIG_FMAN_ENET +#define CONFIG_SYS_RGMII1_PHY_ADDR 0x01 +#define CONFIG_SYS_RGMII2_PHY_ADDR 0x02 + #define CONFIG_MII /* MII PHY management */ -#define CONFIG_ETHPRIME "FM1@DTSEC1" +#define CONFIG_ETHPRIME "FM1@DTSEC4" #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ #endif @@ -600,7 +604,6 @@ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/ /* * For booting Linux, the board info and command line data @@ -631,9 +634,9 @@ #define __USB_PHY_TYPE utmi #define CONFIG_EXTRA_ENV_SETTINGS \ - "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ - "bank_intlv=cs0_cs1;" \ - "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ + "hwconfig=fsl_ddr:bank_intlv=cs0_cs1;" \ + "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\ + "usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ "netdev=eth0\0" \ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ diff --git a/include/configs/T2080QDS.h b/include/configs/T208xQDS.h index 9bd0fe2382..5b22d64467 100644 --- a/include/configs/T2080QDS.h +++ b/include/configs/T208xQDS.h @@ -5,21 +5,25 @@ */ /* - * T2080 QDS board configuration file + * T2080/T2081 QDS board configuration file */ -#ifndef __T2080QDS_H -#define __T2080QDS_H +#ifndef __T208xQDS_H +#define __T208xQDS_H -#define CONFIG_T2080QDS #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ #define CONFIG_MMC #define CONFIG_SPI_FLASH #define CONFIG_USB_EHCI +#if defined(CONFIG_PPC_T2080) +#define CONFIG_T2080QDS #define CONFIG_FSL_SATA_V2 #define CONFIG_SYS_SRIO /* Enable Serial RapidIO Support */ #define CONFIG_SRIO1 /* SRIO port 1 */ #define CONFIG_SRIO2 /* SRIO port 2 */ +#elif defined(CONFIG_PPC_T2081) +#define CONFIG_T2081QDS +#endif /* High Level Configuration Options */ #define CONFIG_PHYS_64BIT @@ -44,8 +48,12 @@ #ifdef CONFIG_RAMBOOT_PBL #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc -#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t2080qds/t2080_pbi.cfg -#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t2080qds/t2080_rcw.cfg +#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t208xqds/t208x_pbi.cfg +#if defined(CONFIG_PPC_T2080) +#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t208xqds/t2080_rcw.cfg +#elif defined(CONFIG_PPC_T2081) +#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t208xqds/t2081_rcw.cfg +#endif #endif #define CONFIG_SRIO_PCIE_BOOT_MASTER @@ -447,7 +455,12 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_FSL_ESPI #define CONFIG_SPI_FLASH_SST #define CONFIG_SPI_FLASH_STMICRO +#if defined(CONFIG_T2080QDS) #define CONFIG_SPI_FLASH_SPANSION +#elif defined(CONFIG_T2081QDS) +#define CONFIG_SPI_FLASH_EON +#endif + #define CONFIG_CMD_SF #define CONFIG_SF_DEFAULT_SPEED 10000000 #define CONFIG_SF_DEFAULT_MODE 0 @@ -505,7 +518,7 @@ unsigned long get_board_ddr_clk(void); #ifdef CONFIG_PCI #define CONFIG_PCI_INDIRECT_BRIDGE -#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */ +#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ #define CONFIG_NET_MULTI #define CONFIG_E1000 #define CONFIG_PCI_PNP /* do pci plug-and-play */ @@ -680,7 +693,6 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/ /* * For booting Linux, the board info and command line data @@ -801,4 +813,4 @@ unsigned long get_board_ddr_clk(void); #undef CONFIG_CMD_USB #endif -#endif /* __T2080QDS_H */ +#endif /* __T208xQDS_H */ diff --git a/include/configs/ac14xx.h b/include/configs/ac14xx.h index aa584b7768..f57820d8f5 100644 --- a/include/configs/ac14xx.h +++ b/include/configs/ac14xx.h @@ -289,9 +289,8 @@ #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SRAM_BASE #define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_SRAM_SIZE -#define CONFIG_SYS_GBL_DATA_SIZE 0x100 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \ - CONFIG_SYS_GBL_DATA_SIZE) + GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE diff --git a/include/configs/actux1.h b/include/configs/actux1.h deleted file mode 100644 index 9b8bd78943..0000000000 --- a/include/configs/actux1.h +++ /dev/null @@ -1,226 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * Configuration settings for the AcTux-1 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_IXP425 1 -#define CONFIG_ACTUX1 1 - -#define CONFIG_MACH_TYPE 1479 - -#define CONFIG_DISPLAY_CPUINFO 1 -#define CONFIG_DISPLAY_BOARDINFO 1 - -#define CONFIG_IXP_SERIAL -#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART2 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 3 -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_BOARD_EARLY_INIT_F 1 -#define CONFIG_SYS_LDSCRIPT "board/actux1/u-boot.lds" - -/*************************************************************** - * U-boot generic defines start here. - ***************************************************************/ -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* Command line configuration. */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ELF -#ifdef CONFIG_PCI -#define CONFIG_CMD_PCI -#define CONFIG_PCI_PNP -#define CONFIG_IXP_PCI -#define CONFIG_PCI_SCAN_SHOW -#define CONFIG_CMD_PCI_ENUM -#endif - -#define CONFIG_BOOTCOMMAND "run boot_flash" -/* enable passing of ATAGs */ -#define CONFIG_CMDLINE_TAG 1 -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 -#define CONFIG_REVISION_TAG 1 - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_KGDB_BAUDRATE 230400 -#endif - -/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP -/* Console I/O Buffer Size */ -#define CONFIG_SYS_CBSIZE 256 -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -/* max number of command args */ -#define CONFIG_SYS_MAXARGS 16 -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x00400000 -#define CONFIG_SYS_MEMTEST_END 0x00800000 - -/* timer clock - 2* OSC_IN system clock */ -#define CONFIG_IXP425_TIMER_CLK 66666666 - -/* default load address */ -#define CONFIG_SYS_LOAD_ADDR 0x00010000 - -/* valid baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200, 230400 } -#define CONFIG_SERIAL_RTS_ACTIVE 1 - -/* Expansion bus settings */ -#define CONFIG_SYS_EXP_CS0 0xbd113842 - -/* SDRAM settings */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM_1 0x00000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -#ifdef CONFIG_RAM_32MB -# define CONFIG_SYS_SDR_CONFIG 0x18 -# define PHYS_SDRAM_1_SIZE 0x02000000 -# define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a -# define CONFIG_SYS_SDR_MODE_CONFIG 0x1 -# define CONFIG_SYS_DRAM_SIZE 0x02000000 -#else /* 16MB SDRAM */ -# define CONFIG_SYS_SDR_CONFIG 0x3A -# define PHYS_SDRAM_1_SIZE 0x01000000 -# define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a -# define CONFIG_SYS_SDR_MODE_CONFIG 0x1 -# define CONFIG_SYS_DRAM_SIZE 0x01000000 -#endif - -/* FLASH organization */ -#define CONFIG_SYS_TEXT_BASE 0x50000000 -#ifdef CONFIG_FLASH2X2 -# define CONFIG_SYS_MAX_FLASH_BANKS 2 -/* max number of sectors on one chip */ -# define CONFIG_SYS_MAX_FLASH_SECT 40 -# define PHYS_FLASH_1 0x50000000 -# define PHYS_FLASH_2 0x50200000 -# define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2 } -#endif -#ifdef CONFIG_FLASH1X8 -# define CONFIG_SYS_MAX_FLASH_BANKS 1 -/* max number of sectors on one chip */ -# define CONFIG_SYS_MAX_FLASH_SECT 140 -# define PHYS_FLASH_1 0x50000000 -# define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1 } -#endif - -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) -#define CONFIG_BOARD_SIZE_LIMIT 262144 - -/* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -/* no byte writes on IXP4xx */ -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT -/* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_EMPTY_INFO - -/* Ethernet */ - -/* include IXP4xx NPE support */ -#define CONFIG_IXP4XX_NPE 1 -/* NPE0 PHY address */ -#define CONFIG_PHY_ADDR 0 -/* NPE1 PHY address (HW Release E only) */ -#define CONFIG_PHY1_ADDR 1 -/* MII PHY management */ -#define CONFIG_MII 1 -/* Number of ethernet rx buffers & descriptors */ -#define CONFIG_SYS_RX_ETH_BUFFER 16 -#define CONFIG_RESET_PHY_R 1 - -#define CONFIG_HAS_ETH1 1 - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_NET -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#undef CONFIG_CMD_NFS - -/* BOOTP options */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 32 - -/* - * environment organization: - * one flash sector, embedded in uboot area (bottom bootblock flash) - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x4000) -#define CONFIG_SYS_USE_PPCENV 1 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "npe_ucode=50040000\0" \ - "mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \ - "kerneladdr=50050000\0" \ - "kernelfile=actux1/uImage\0" \ - "rootfile=actux1/rootfs\0" \ - "rootaddr=50170000\0" \ - "loadaddr=10000\0" \ - "updateboot_ser=mw.b 10000 ff 40000;" \ - " loady ${loadaddr};" \ - " run eraseboot writeboot\0" \ - "updateboot_net=mw.b 10000 ff 40000;" \ - " tftp ${loadaddr} actux1/u-boot.bin;" \ - " run eraseboot writeboot\0" \ - "eraseboot=protect off 50000000 50003fff;" \ - " protect off 50006000 5003ffff;" \ - " erase 50000000 50003fff;" \ - " erase 50006000 5003ffff\0" \ - "writeboot=cp.b 10000 50000000 4000;" \ - " cp.b 16000 50006000 3a000\0" \ - "updateucode=loady;" \ - " era ${npe_ucode} +${filesize};" \ - " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ - "updateroot=tftp ${loadaddr} ${rootfile};" \ - " era ${rootaddr} +${filesize};" \ - " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ - "updatekern=tftp ${loadaddr} ${kernelfile};" \ - " era ${kerneladdr} +${filesize};" \ - " cp.b ${loadaddr} ${kerneladdr} ${filesize}\0" \ - "flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0" \ - "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \ - "boot_flash=run flashargs addtty addeth;" \ - " bootm ${kerneladdr}\0" \ - "boot_net=run netargs addtty addeth;" \ - " tftpboot ${loadaddr} ${kernelfile};" \ - " bootm\0" - -/* additions for new relocation code, must be added to all boards */ -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) - -#endif /* __CONFIG_H */ diff --git a/include/configs/actux2.h b/include/configs/actux2.h deleted file mode 100644 index f0cbff79ca..0000000000 --- a/include/configs/actux2.h +++ /dev/null @@ -1,206 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * Configuration settings for the AcTux-2 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_IXP425 1 -#define CONFIG_ACTUX2 1 - -#define CONFIG_MACH_TYPE 1480 - -#define CONFIG_DISPLAY_CPUINFO 1 -#define CONFIG_DISPLAY_BOARDINFO 1 - -#define CONFIG_IXP_SERIAL -#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART2 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 5 -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_BOARD_EARLY_INIT_F 1 -#define CONFIG_SYS_LDSCRIPT "board/actux2/u-boot.lds" - -/*************************************************************** - * U-boot generic defines start here. - ***************************************************************/ -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* Command line configuration. */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ELF -#undef CONFIG_CMD_PCI -#undef CONFIG_PCI - -#define CONFIG_BOOTCOMMAND "run boot_flash" -/* enable passing of ATAGs */ -#define CONFIG_CMDLINE_TAG 1 -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 -#define CONFIG_REVISION_TAG 1 - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_KGDB_BAUDRATE 230400 -#endif - -/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP -/* Console I/O Buffer Size */ -#define CONFIG_SYS_CBSIZE 256 -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -/* max number of command args */ -#define CONFIG_SYS_MAXARGS 16 -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x00400000 -#define CONFIG_SYS_MEMTEST_END 0x00800000 - -/* timer clock - 2* OSC_IN system clock */ -#define CONFIG_IXP425_TIMER_CLK 66666666 - -/* default load address */ -#define CONFIG_SYS_LOAD_ADDR 0x00010000 - -/* valid baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200, 230400 } -#define CONFIG_SERIAL_RTS_ACTIVE 1 - -/* Expansion bus settings */ -#define CONFIG_SYS_EXP_CS0 0xbd113042 - -/* SDRAM settings */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM_1 0x00000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -/* 16MB SDRAM */ -#define CONFIG_SYS_SDR_CONFIG 0x3A -#define PHYS_SDRAM_1_SIZE 0x01000000 -#define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a -#define CONFIG_SYS_SDR_MODE_CONFIG 0x1 -#define CONFIG_SYS_DRAM_SIZE 0x01000000 - -/* FLASH organization */ -#define CONFIG_SYS_TEXT_BASE 0x50000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -/* max number of sectors on one chip */ -#define CONFIG_SYS_MAX_FLASH_SECT 140 -#define PHYS_FLASH_1 0x50000000 -#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1 } - -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) -#define CONFIG_BOARD_SIZE_LIMIT 262144 - -/* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -/* no byte writes on IXP4xx */ -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT - -/* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_EMPTY_INFO - -/* Ethernet */ - -/* include IXP4xx NPE support */ -#define CONFIG_IXP4XX_NPE 1 -/* NPE0 PHY address */ -#define CONFIG_PHY_ADDR 0x00 -/* MII PHY management */ -#define CONFIG_MII 1 -/* fixed-speed switch without standard PHY registers on MII */ -#define CONFIG_MII_NPE0_FIXEDLINK 1 -#define CONFIG_MII_NPE0_SPEED 100 -#define CONFIG_MII_NPE0_FULLDUPLEX 1 - -/* Number of ethernet rx buffers & descriptors */ -#define CONFIG_SYS_RX_ETH_BUFFER 16 -#define CONFIG_RESET_PHY_R 1 -/* ethernet switch connected to MII port */ -#define CONFIG_MII_ETHSWITCH 1 - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_NET -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#undef CONFIG_CMD_NFS - -/* BOOTP options */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 32 - -/* - * environment organization: - * one flash sector, embedded in uboot area (bottom bootblock flash) - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x4000) -#define CONFIG_SYS_USE_PPCENV 1 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "npe_ucode=50040000\0" \ - "mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \ - "kerneladdr=50050000\0" \ - "kernelfile=actux2/uImage\0" \ - "rootfile=actux2/rootfs\0" \ - "rootaddr=50170000\0" \ - "loadaddr=10000\0" \ - "updateboot_ser=mw.b 10000 ff 40000;" \ - " loady ${loadaddr};" \ - " run eraseboot writeboot\0" \ - "updateboot_net=mw.b 10000 ff 40000;" \ - " tftp ${loadaddr} actux2/u-boot.bin;" \ - " run eraseboot writeboot\0" \ - "eraseboot=protect off 50000000 50003fff;" \ - " protect off 50006000 5003ffff;" \ - " erase 50000000 50003fff;" \ - " erase 50006000 5003ffff\0" \ - "writeboot=cp.b 10000 50000000 4000;" \ - " cp.b 16000 50006000 3a000\0" \ - "updateucode=loady;" \ - " era ${npe_ucode} +${filesize};" \ - " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ - "updateroot=tftp ${loadaddr} ${rootfile};" \ - " era ${rootaddr} +${filesize};" \ - " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ - "updatekern=tftp ${loadaddr} ${kernelfile};" \ - " era ${kerneladdr} +${filesize};" \ - " cp.b ${loadaddr} ${kerneladdr} ${filesize}\0" \ - "flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ - "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \ - "boot_flash=run flashargs addtty addeth;" \ - " bootm ${kerneladdr}\0" \ - "boot_net=run netargs addtty addeth;" \ - " tftpboot ${loadaddr} ${kernelfile};" \ - " bootm\0" - -/* additions for new relocation code, must be added to all boards */ -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) - -#endif /* __CONFIG_H */ diff --git a/include/configs/actux3.h b/include/configs/actux3.h deleted file mode 100644 index 763910745c..0000000000 --- a/include/configs/actux3.h +++ /dev/null @@ -1,205 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * Configuration settings for the AcTux-3 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_IXP425 1 -#define CONFIG_ACTUX3 1 - -#define CONFIG_MACH_TYPE 1481 - -#define CONFIG_DISPLAY_CPUINFO 1 -#define CONFIG_DISPLAY_BOARDINFO 1 - -#define CONFIG_IXP_SERIAL -#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART2 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 3 -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_BOARD_EARLY_INIT_F 1 -#define CONFIG_SYS_LDSCRIPT "board/actux3/u-boot.lds" - -/*************************************************************** - * U-boot generic defines start here. - ***************************************************************/ -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* Command line configuration. */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ELF - -#define CONFIG_BOOTCOMMAND "run boot_flash" -/* enable passing of ATAGs */ -#define CONFIG_CMDLINE_TAG 1 -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 -#define CONFIG_REVISION_TAG 1 - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_KGDB_BAUDRATE 230400 -#endif - -/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP -/* Console I/O Buffer Size */ -#define CONFIG_SYS_CBSIZE 256 -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -/* max number of command args */ -#define CONFIG_SYS_MAXARGS 16 -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x00400000 -#define CONFIG_SYS_MEMTEST_END 0x00800000 - -/* timer clock - 2* OSC_IN system clock */ -#define CONFIG_IXP425_TIMER_CLK 66666666 - -/* default load address */ -#define CONFIG_SYS_LOAD_ADDR 0x00010000 - -/* valid baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200, 230400 } -#define CONFIG_SERIAL_RTS_ACTIVE 1 - -/* Expansion bus settings */ -#define CONFIG_SYS_EXP_CS0 0xbd113442 - -/* SDRAM settings */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM_1 0x00000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -/* 16MB SDRAM */ -#define CONFIG_SYS_SDR_CONFIG 0x3A -#define PHYS_SDRAM_1_SIZE 0x01000000 -#define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a -#define CONFIG_SYS_SDR_MODE_CONFIG 0x1 -#define CONFIG_SYS_DRAM_SIZE 0x01000000 - -/* FLASH organization */ -#define CONFIG_SYS_TEXT_BASE 0x50000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -/* max number of sectors on one chip */ -#define CONFIG_SYS_MAX_FLASH_SECT 140 -#define PHYS_FLASH_1 0x50000000 -#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1 } - -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) -#define CONFIG_BOARD_SIZE_LIMIT 262144 - -/* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -/* no byte writes on IXP4xx */ -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT - -/* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_EMPTY_INFO - -/* Ethernet */ - -/* include IXP4xx NPE support */ -#define CONFIG_IXP4XX_NPE 1 - -/* NPE0 PHY address */ -#define CONFIG_PHY_ADDR 0x10 -/* MII PHY management */ -#define CONFIG_MII 1 -/* fixed-speed switch without standard PHY registers on MII */ -#define CONFIG_MII_NPE0_FIXEDLINK 1 -#define CONFIG_MII_NPE0_SPEED 100 -#define CONFIG_MII_NPE0_FULLDUPLEX 1 - -/* Number of ethernet rx buffers & descriptors */ -#define CONFIG_SYS_RX_ETH_BUFFER 16 -#define CONFIG_RESET_PHY_R 1 -/* ethernet switch connected to MII port */ -#define CONFIG_MII_ETHSWITCH 1 - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_NET -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#undef CONFIG_CMD_NFS - -/* BOOTP options */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 32 - -/* - * environment organization: - * one flash sector, embedded in uboot area (bottom bootblock flash) - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x4000) -#define CONFIG_SYS_USE_PPCENV 1 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "npe_ucode=50040000\0" \ - "mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \ - "kerneladdr=50050000\0" \ - "kernelfile=actux3/uImage\0" \ - "rootfile=actux3/rootfs\0" \ - "rootaddr=50170000\0" \ - "loadaddr=10000\0" \ - "updateboot_ser=mw.b 10000 ff 40000;" \ - " loady ${loadaddr};" \ - " run eraseboot writeboot\0" \ - "updateboot_net=mw.b 10000 ff 40000;" \ - " tftp ${loadaddr} actux3/u-boot.bin;" \ - " run eraseboot writeboot\0" \ - "eraseboot=protect off 50000000 50003fff;" \ - " protect off 50006000 5003ffff;" \ - " erase 50000000 50003fff;" \ - " erase 50006000 5003ffff\0" \ - "writeboot=cp.b 10000 50000000 4000;" \ - " cp.b 16000 50006000 3a000\0" \ - "updateucode=loady;" \ - " era ${npe_ucode} +${filesize};" \ - " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ - "updateroot=tftp ${loadaddr} ${rootfile};" \ - " era ${rootaddr} +${filesize};" \ - " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ - "updatekern=tftp ${loadaddr} ${kernelfile};" \ - " era ${kerneladdr} +${filesize};" \ - " cp.b ${loadaddr} ${kerneladdr} ${filesize}\0" \ - "flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0" \ - "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \ - "boot_flash=run flashargs addtty addeth;" \ - " bootm ${kerneladdr}\0" \ - "boot_net=run netargs addtty addeth;" \ - " tftpboot ${loadaddr} ${kernelfile};" \ - " bootm\0" - -/* additions for new relocation code, must be added to all boards */ -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) - -#endif /* __CONFIG_H */ diff --git a/include/configs/actux4.h b/include/configs/actux4.h deleted file mode 100644 index 12bd98a7e1..0000000000 --- a/include/configs/actux4.h +++ /dev/null @@ -1,204 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * Configuration settings for the AcTux-4 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_IXP425 1 -#define CONFIG_ACTUX4 1 - -#define CONFIG_MACH_TYPE 1532 - -#define CONFIG_DISPLAY_CPUINFO 1 -#define CONFIG_DISPLAY_BOARDINFO 1 - -#define CONFIG_IXP_SERIAL -#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART1 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 3 -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_BOARD_EARLY_INIT_F 1 - -/*************************************************************** - * U-boot generic defines start here. - ***************************************************************/ -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* Command line configuration */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ELF - -#define CONFIG_PCI -#ifdef CONFIG_PCI -#define CONFIG_CMD_PCI -#define CONFIG_PCI_PNP -#define CONFIG_IXP_PCI -#define CONFIG_PCI_SCAN_SHOW -#define CONFIG_CMD_PCI_ENUM -#endif - -#define CONFIG_BOOTCOMMAND "run boot_flash" -/* enable passing of ATAGs */ -#define CONFIG_CMDLINE_TAG 1 -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_KGDB_BAUDRATE 230400 -#endif - -/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP -/* Console I/O Buffer Size */ -#define CONFIG_SYS_CBSIZE 256 -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -/* max number of command args */ -#define CONFIG_SYS_MAXARGS 16 -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x00400000 -#define CONFIG_SYS_MEMTEST_END 0x00800000 - -/* timer clock - 2* OSC_IN system clock */ -#define CONFIG_IXP425_TIMER_CLK 66000000 - -/* default load address */ -#define CONFIG_SYS_LOAD_ADDR 0x00010000 - -/* valid baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200, 230400 } -#define CONFIG_SERIAL_RTS_ACTIVE 1 - -/* Expansion bus settings */ -#define CONFIG_SYS_EXP_CS0 0xbd113003 - -/* SDRAM settings */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM_1 0x00000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -/* 32MB SDRAM */ -#define CONFIG_SYS_SDR_CONFIG 0x18 -#define PHYS_SDRAM_1_SIZE 0x02000000 -#define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a -#define CONFIG_SYS_SDR_MODE_CONFIG 0x1 -#define CONFIG_SYS_DRAM_SIZE 0x02000000 - -/* FLASH organization */ -#define CONFIG_SYS_TEXT_BASE 0x50000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 2 -/* max # of sectors per chip */ -#define CONFIG_SYS_MAX_FLASH_SECT 70 -#define PHYS_FLASH_1 0x50000000 -#define PHYS_FLASH_2 0x51000000 -#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2 } - -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_LEN (252 << 10) -#define CONFIG_BOARD_SIZE_LIMIT 258048 - -/* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -/* board provides its own flash_init code */ -#define CONFIG_FLASH_CFI_LEGACY 1 -/* no byte writes on IXP4xx */ -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT -/* SST 39VF020 etc. support */ -#define CONFIG_SYS_FLASH_LEGACY_256Kx8 1 - -/* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_EMPTY_INFO - -/* Ethernet */ - -/* include IXP4xx NPE support */ -#define CONFIG_IXP4XX_NPE 1 - -/* NPE0 PHY address */ -#define CONFIG_PHY_ADDR 0x1C -/* MII PHY management */ -#define CONFIG_MII 1 - -/* Number of ethernet rx buffers & descriptors */ -#define CONFIG_SYS_RX_ETH_BUFFER 16 - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_NET -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#undef CONFIG_CMD_NFS - -/* BOOTP options */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 32 - -/* environment organization: one complete 4k flash sector */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x1000 -#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x3f000) - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "npe_ucode=51000000\0" \ - "mtd=IXP4XX-Flash.0:252k(uboot),4k(uboot_env);" \ - "IXP4XX-Flash.1:128k(ucode),1280k(linux),-(root)\0" \ - "kerneladdr=51020000\0" \ - "kernelfile=actux4/uImage\0" \ - "rootfile=actux4/rootfs\0" \ - "rootaddr=51160000\0" \ - "loadaddr=10000\0" \ - "updateboot_ser=mw.b 10000 ff 40000;" \ - " loady ${loadaddr};" \ - " run eraseboot writeboot\0" \ - "updateboot_net=mw.b 10000 ff 40000;" \ - " tftp ${loadaddr} actux4/u-boot.bin;" \ - " run eraseboot writeboot\0" \ - "eraseboot=protect off 50000000 5003efff;" \ - " erase 50000000 +${filesize}\0" \ - "writeboot=cp.b 10000 50000000 ${filesize}\0" \ - "updateucode=loady;" \ - " era ${npe_ucode} +${filesize};" \ - " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ - "updateroot=tftp ${loadaddr} ${rootfile};" \ - " era ${rootaddr} +${filesize};" \ - " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ - "updatekern=tftp ${loadaddr} ${kernelfile};" \ - " era ${kerneladdr} +${filesize};" \ - " cp.b ${loadaddr} ${kerneladdr} ${filesize}\0" \ - "flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock4" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock4" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ - "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \ - "boot_flash=run flashargs addtty addeth;" \ - " bootm ${kerneladdr}\0" \ - "boot_net=run netargs addtty addeth;" \ - " tftpboot ${loadaddr} ${kernelfile};" \ - " bootm\0" - -/* additions for new relocation code, must be added to all boards */ -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) - -#endif /* __CONFIG_H */ diff --git a/include/configs/adp-ag101.h b/include/configs/adp-ag101.h index e31131f6e2..e318c7543f 100644 --- a/include/configs/adp-ag101.h +++ b/include/configs/adp-ag101.h @@ -139,11 +139,6 @@ #define CONFIG_SYS_MALLOC_LEN (512 << 10) /* - * size in bytes reserved for initial data - */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* * AHB Controller configuration */ #define CONFIG_FTAHBC020S diff --git a/include/configs/adp-ag101p.h b/include/configs/adp-ag101p.h index ded3f331e8..24904b0b7c 100644 --- a/include/configs/adp-ag101p.h +++ b/include/configs/adp-ag101p.h @@ -139,11 +139,6 @@ #define CONFIG_SYS_MALLOC_LEN (512 << 10) /* - * size in bytes reserved for initial data - */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* * AHB Controller configuration */ #define CONFIG_FTAHBC020S diff --git a/include/configs/adp-ag102.h b/include/configs/adp-ag102.h index 1e4ce2e7d9..39f7a3cd46 100644 --- a/include/configs/adp-ag102.h +++ b/include/configs/adp-ag102.h @@ -204,11 +204,6 @@ #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024) /* - * size in bytes reserved for initial data -*/ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* * AHB Controller configuration */ #define CONFIG_FTAHBC020S diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index 73a9adb293..23c056c82c 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -20,6 +20,7 @@ #define MACH_TYPE_TIAM335EVM 3589 /* Until the next sync */ #define CONFIG_MACH_TYPE MACH_TYPE_TIAM335EVM +#define CONFIG_BOARD_LATE_INIT /* Clock Defines */ #define V_OSCK 24000000 /* Clock output from T2 */ @@ -31,6 +32,12 @@ /* Always 128 KiB env size */ #define CONFIG_ENV_SIZE (128 << 10) +/* Enhance our eMMC support / experience. */ +#define CONFIG_CMD_GPT +#define CONFIG_EFI_PARTITION +#define CONFIG_PARTITION_UUIDS +#define CONFIG_CMD_PART + #ifdef CONFIG_NAND #define NANDARGS \ "mtdids=" MTDIDS_DEFAULT "\0" \ @@ -64,6 +71,9 @@ "bootfile=zImage\0" \ "fdtfile=undefined\0" \ "console=ttyO0,115200n8\0" \ + "partitions=" \ + "uuid_disk=${uuid_gpt_disk};" \ + "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}\0" \ "optargs=\0" \ "mmcdev=0\0" \ "mmcroot=/dev/mmcblk0p2 ro\0" \ @@ -295,6 +305,9 @@ #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_USBETH_SUPPORT) /* disable host part of MUSB in SPL */ #undef CONFIG_MUSB_HOST +/* disable EFI partitions and partition UUID support */ +#undef CONFIG_PARTITION_UUIDS +#undef CONFIG_EFI_PARTITION /* * Disable CPSW SPL support so we fit within the 101KiB limit. */ @@ -385,7 +398,6 @@ /* Network. */ #define CONFIG_PHY_GIGE #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_SMSC /* NAND support */ diff --git a/include/configs/am335x_igep0033.h b/include/configs/am335x_igep0033.h index 115d1b37c9..e72ee05ec8 100644 --- a/include/configs/am335x_igep0033.h +++ b/include/configs/am335x_igep0033.h @@ -181,7 +181,6 @@ #define CONFIG_NET_RETRY_COUNT 10 #define CONFIG_NET_MULTI #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_SMSC /* NAND support */ diff --git a/include/configs/am43xx_evm.h b/include/configs/am43xx_evm.h index d3c4756349..614857dd25 100644 --- a/include/configs/am43xx_evm.h +++ b/include/configs/am43xx_evm.h @@ -84,6 +84,32 @@ #define CONFIG_OMAP_USB_PHY #define CONFIG_AM437X_USB2PHY2_HOST +/* SPI */ +#undef CONFIG_OMAP3_SPI +#define CONFIG_TI_QSPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_MACRONIX +#define CONFIG_CMD_SF +#define CONFIG_CMD_SPI +#define CONFIG_TI_SPI_MMAP +#define CONFIG_QSPI_SEL_GPIO 48 +#define CONFIG_SF_DEFAULT_SPEED 48000000 +#define CONFIG_DEFAULT_SPI_MODE SPI_MODE_3 + +/* SPI SPL */ +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_LOAD +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_BUS 0 +#define CONFIG_SPL_SPI_CS 0 +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 + +/* Enhance our eMMC support / experience. */ +#define CONFIG_CMD_GPT +#define CONFIG_EFI_PARTITION +#define CONFIG_PARTITION_UUIDS +#define CONFIG_CMD_PART + #ifndef CONFIG_SPL_BUILD #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x80200000\0" \ @@ -95,6 +121,9 @@ "bootdir=/boot\0" \ "bootfile=zImage\0" \ "console=ttyO0,115200n8\0" \ + "partitions=" \ + "uuid_disk=${uuid_gpt_disk};" \ + "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}\0" \ "optargs=\0" \ "mmcdev=0\0" \ "mmcroot=/dev/mmcblk0p2 rw\0" \ @@ -176,4 +205,30 @@ "run usbboot;" #endif + +/* CPSW Ethernet */ +#define CONFIG_CMD_NET +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING +#define CONFIG_CMD_MII +#define CONFIG_DRIVER_TI_CPSW +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_NET_MULTI +#define CONFIG_PHY_GIGE +#define CONFIG_PHYLIB + +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_NET_VCI_STRING "AM43xx U-Boot SPL" + +#define CONFIG_SPL_ETH_SUPPORT +#define CONFIG_SPL_NET_SUPPORT +#define CONFIG_SYS_RX_ETH_BUFFER 64 + #endif /* __CONFIG_AM43XX_EVM_H */ diff --git a/include/configs/ap_sh4a_4a.h b/include/configs/ap_sh4a_4a.h index bb39491f8b..4282d70266 100644 --- a/include/configs/ap_sh4a_4a.h +++ b/include/configs/ap_sh4a_4a.h @@ -134,8 +134,6 @@ #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Size of DRAM reserved for malloc() use */ #define CONFIG_SYS_MALLOC_LEN (256 * 1024) -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE (256) #define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) /* ENV setting */ diff --git a/include/configs/apf27.h b/include/configs/apf27.h index 1193013ea0..b10c48c20e 100644 --- a/include/configs/apf27.h +++ b/include/configs/apf27.h @@ -356,11 +356,6 @@ #endif /* CONFIG_CMD_DATE */ /* - * Clocks - */ -#define CONFIG_SYS_HZ 1000 /* Ticks per second */ - -/* * PLL * * 31 | x |x| x x x x |x x x x x x x x x x |x x|x x x x|x x x x x x x x x x| 0 diff --git a/include/configs/arcangel4-be.h b/include/configs/arcangel4-be.h new file mode 100644 index 0000000000..88d27db08b --- /dev/null +++ b/include/configs/arcangel4-be.h @@ -0,0 +1,92 @@ +/* + * Copyright (C) 2013-2014 Synopsys, Inc. All rights reserved. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_ARCANGEL4_H_ +#define _CONFIG_ARCANGEL4_H_ + +/* + * CPU configuration + */ +#define CONFIG_SYS_BIG_ENDIAN +#define CONFIG_ARC700 +#define CONFIG_ARC_MMU_VER 3 +#define CONFIG_SYS_CACHELINE_SIZE 64 +#define CONFIG_SYS_CLK_FREQ 70000000 +#define CONFIG_SYS_TIMER_RATE CONFIG_SYS_CLK_FREQ + +/* + * Board configuration + */ +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is in RAM already */ + +#define CONFIG_ARCH_EARLY_INIT_R + +/* + * Memory configuration + */ +#define CONFIG_SYS_TEXT_BASE 0x81000000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_SYS_SDRAM_SIZE 0x10000000 /* 256 Mb */ + +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) + +#define CONFIG_SYS_MALLOC_LEN 0x200000 /* 2 MB */ +#define CONFIG_SYS_BOOTM_LEN 0x2000000 /* 32 MB */ +#define CONFIG_SYS_LOAD_ADDR 0x82000000 + +#define CONFIG_SYS_NO_FLASH + +/* + * UART configuration + * + */ +#define CONFIG_ARC_SERIAL +#define CONFIG_ARC_UART_BASE 0xC0FC1000 +#define CONFIG_BAUDRATE 115200 + +/* + * Command line configuration + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ELF + +#define CONFIG_OF_LIBFDT + +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_MAXARGS 16 + +/* + * Environment settings + */ +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_SIZE 0x00200 /* 512 bytes */ +#define CONFIG_ENV_OFFSET 0 + +/* + * Environment configuration + */ +#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_BOOTARGS "console=ttyARC0,115200n8" +#define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR + +/* + * Console configuration + */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_PROMPT "arcangel4# " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) + +#endif /* _CONFIG_ARCANGEL4_H_ */ diff --git a/include/configs/arcangel4.h b/include/configs/arcangel4.h new file mode 100644 index 0000000000..4579eb97c2 --- /dev/null +++ b/include/configs/arcangel4.h @@ -0,0 +1,91 @@ +/* + * Copyright (C) 2013-2014 Synopsys, Inc. All rights reserved. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_ARCANGEL4_H_ +#define _CONFIG_ARCANGEL4_H_ + +/* + * CPU configuration + */ +#define CONFIG_ARC700 +#define CONFIG_ARC_MMU_VER 3 +#define CONFIG_SYS_CACHELINE_SIZE 64 +#define CONFIG_SYS_CLK_FREQ 70000000 +#define CONFIG_SYS_TIMER_RATE CONFIG_SYS_CLK_FREQ + +/* + * Board configuration + */ +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is in RAM already */ + +#define CONFIG_ARCH_EARLY_INIT_R + +/* + * Memory configuration + */ +#define CONFIG_SYS_TEXT_BASE 0x81000000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_SYS_SDRAM_SIZE 0x10000000 /* 256 Mb */ + +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) + +#define CONFIG_SYS_MALLOC_LEN 0x200000 /* 2 MB */ +#define CONFIG_SYS_BOOTM_LEN 0x2000000 /* 32 MB */ +#define CONFIG_SYS_LOAD_ADDR 0x82000000 + +#define CONFIG_SYS_NO_FLASH + +/* + * UART configuration + * + */ +#define CONFIG_ARC_SERIAL +#define CONFIG_ARC_UART_BASE 0xC0FC1000 +#define CONFIG_BAUDRATE 115200 + +/* + * Command line configuration + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ELF + +#define CONFIG_OF_LIBFDT + +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_MAXARGS 16 + +/* + * Environment settings + */ +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_SIZE 0x00200 /* 512 bytes */ +#define CONFIG_ENV_OFFSET 0 + +/* + * Environment configuration + */ +#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_BOOTARGS "console=ttyARC0,115200n8" +#define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR + +/* + * Console configuration + */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_PROMPT "arcangel4# " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) + +#endif /* _CONFIG_ARCANGEL4_H_ */ diff --git a/include/configs/armadillo-800eva.h b/include/configs/armadillo-800eva.h index e5569c7296..17a2da034d 100644 --- a/include/configs/armadillo-800eva.h +++ b/include/configs/armadillo-800eva.h @@ -94,7 +94,6 @@ #define CONFIG_SYS_MONITOR_BASE 0x00000000 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) #define CONFIG_SYS_MALLOC_LEN (1 * 1024 * 1024) -#define CONFIG_SYS_GBL_DATA_SIZE (256) #define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) #define CONFIG_SYS_TEXT_BASE 0xE80C0000 diff --git a/include/configs/arndale.h b/include/configs/arndale.h index 9584d82af7..515facfd67 100644 --- a/include/configs/arndale.h +++ b/include/configs/arndale.h @@ -22,8 +22,6 @@ #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO -/* Enable fdt support for Exynos5250 */ -#define CONFIG_ARCH_DEVICE_TREE exynos5250 #define CONFIG_OF_CONTROL #define CONFIG_OF_SEPARATE diff --git a/include/configs/axs101.h b/include/configs/axs101.h new file mode 100644 index 0000000000..f6b569abfd --- /dev/null +++ b/include/configs/axs101.h @@ -0,0 +1,181 @@ +/* + * Copyright (C) 2013-2014 Synopsys, Inc. All rights reserved. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_AXS101_H_ +#define _CONFIG_AXS101_H_ + +/* + * CPU configuration + */ +#define CONFIG_ARC700 +#define CONFIG_ARC_MMU_VER 3 +#define CONFIG_SYS_CACHELINE_SIZE 32 +#define CONFIG_SYS_CLK_FREQ 750000000 +#define CONFIG_SYS_TIMER_RATE CONFIG_SYS_CLK_FREQ + +/* dwgmac doesn't work with D$ enabled now */ +#define CONFIG_SYS_DCACHE_OFF + +/* + * Board configuration + */ +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is in RAM already */ + +#define CONFIG_ARCH_EARLY_INIT_R + +#define ARC_FPGA_PERIPHERAL_BASE 0xE0000000 +#define ARC_APB_PERIPHERAL_BASE 0xF0000000 +#define ARC_DWMMC_BASE (ARC_FPGA_PERIPHERAL_BASE + 0x15000) +#define ARC_DWGMAC_BASE (ARC_FPGA_PERIPHERAL_BASE + 0x18000) + +/* + * Memory configuration + */ +#define CONFIG_SYS_TEXT_BASE 0x81000000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_SYS_SDRAM_SIZE 0x10000000 /* 256 Mb */ + +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) + +#define CONFIG_SYS_MALLOC_LEN 0x200000 /* 2 MB */ +#define CONFIG_SYS_BOOTM_LEN 0x2000000 /* 32 MB */ +#define CONFIG_SYS_LOAD_ADDR 0x82000000 + +/* + * NAND Flash configuration + */ +#define CONFIG_SYS_NO_FLASH +#define CONFIG_SYS_NAND_BASE (ARC_FPGA_PERIPHERAL_BASE + 0x16000) +#define CONFIG_SYS_MAX_NAND_DEVICE 1 + +/* + * UART configuration + * + * CONFIG_CONS_INDEX = 1 - Debug UART + * CONFIG_CONS_INDEX = 4 - FPGA UART connected to FTDI/USB + */ +#define CONFIG_CONS_INDEX 4 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE -4 +#if (CONFIG_CONS_INDEX == 1) + /* Debug UART */ +# define CONFIG_SYS_NS16550_CLK 33333000 +#else + /* FPGA UARTs use different clock */ +# define CONFIG_SYS_NS16550_CLK 33333333 +#endif +#define CONFIG_SYS_NS16550_COM1 (ARC_APB_PERIPHERAL_BASE + 0x5000) +#define CONFIG_SYS_NS16550_COM2 (ARC_FPGA_PERIPHERAL_BASE + 0x20000) +#define CONFIG_SYS_NS16550_COM3 (ARC_FPGA_PERIPHERAL_BASE + 0x21000) +#define CONFIG_SYS_NS16550_COM4 (ARC_FPGA_PERIPHERAL_BASE + 0x22000) +#define CONFIG_SYS_NS16550_MEM32 + +#define CONFIG_BAUDRATE 115200 +/* + * I2C configuration + */ +#define CONFIG_HARD_I2C +#define CONFIG_DW_I2C +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_ENV_EEPROM_BUS 2 +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_SLAVE 0 +#define CONFIG_SYS_I2C_BASE 0xE001D000 +#define CONFIG_SYS_I2C_BASE1 0xE001E000 +#define CONFIG_SYS_I2C_BASE2 0xE001F000 +#define CONFIG_SYS_I2C_BUS_MAX 3 +#define IC_CLK 50 + +/* + * EEPROM configuration + */ +#define CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR (0xA8 >> 1) +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 32 + +/* + * SD/MMC configuration + */ +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_DWMMC +#define CONFIG_DOS_PARTITION + +/* + * Ethernet PHY configuration + */ +#define CONFIG_PHYLIB +#define CONFIG_MII +#define CONFIG_PHY_GIGE + +/* + * Ethernet configuration + */ +#define CONFIG_DESIGNWARE_ETH +#define CONFIG_DW_AUTONEG +#define CONFIG_DW_SEARCH_PHY +#define CONFIG_NET_MULTI + +/* + * Command line configuration + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_FAT +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MMC +#define CONFIG_CMD_NAND +#define CONFIG_CMD_PING +#define CONFIG_CMD_RARP + +#define CONFIG_OF_LIBFDT + +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_MAXARGS 16 + +/* + * Environment settings + */ +#define CONFIG_ENV_IS_IN_EEPROM +#define CONFIG_ENV_SIZE 0x00200 /* 512 bytes */ +#define CONFIG_ENV_OFFSET 0 + +/* + * Environment configuration + */ +#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_BOOTARGS "console=ttyS3,115200n8" +#define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR + +/* + * Console configuration + */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_PROMPT "AXS# " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) + +/* + * Misc utility configuration + */ +#define CONFIG_BOUNCE_BUFFER + +#endif /* _CONFIG_AXS101_H_ */ diff --git a/include/configs/balloon3.h b/include/configs/balloon3.h index b41a823600..5228ba6ef7 100644 --- a/include/configs/balloon3.h +++ b/include/configs/balloon3.h @@ -84,7 +84,6 @@ * Clock Configuration */ #undef CONFIG_SYS_CLKS_IN_HZ -#define CONFIG_SYS_HZ 1000 #define CONFIG_SYS_CPUSPEED 0x290 /* 520MHz */ /* diff --git a/include/configs/bcm28155_ap.h b/include/configs/bcm28155_ap.h new file mode 100644 index 0000000000..8e1c81fc13 --- /dev/null +++ b/include/configs/bcm28155_ap.h @@ -0,0 +1,140 @@ +/* + * Copyright 2013 Broadcom Corporation. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __BCM28155_AP_H +#define __BCM28155_AP_H + +#include <asm/sizes.h> +#include <asm/arch/sysmap.h> + +/* Architecture, CPU, chip, mach, etc */ +#define CONFIG_ARMV7 +#define CONFIG_KONA +#define CONFIG_SKIP_LOWLEVEL_INIT + +/* + * Memory configuration + */ +#define CONFIG_SYS_TEXT_BASE 0xae000000 + +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_SDRAM_SIZE 0x80000000 +#define CONFIG_NR_DRAM_BANKS 1 + +#define CONFIG_SYS_MALLOC_LEN SZ_4M /* see armv7/start.S. */ +#define CONFIG_STACKSIZE SZ_256K + +/* GPIO Driver */ +#define CONFIG_KONA_GPIO + +/* MMC/SD Driver */ +#define CONFIG_SDHCI +#define CONFIG_MMC_SDMA +#define CONFIG_KONA_SDHCI +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC + +#define CONFIG_SYS_SDIO_BASE0 SDIO1_BASE_ADDR +#define CONFIG_SYS_SDIO_BASE1 SDIO2_BASE_ADDR +#define CONFIG_SYS_SDIO_BASE2 SDIO3_BASE_ADDR +#define CONFIG_SYS_SDIO_BASE3 SDIO4_BASE_ADDR +#define CONFIG_SYS_SDIO0_MAX_CLK 48000000 +#define CONFIG_SYS_SDIO1_MAX_CLK 48000000 +#define CONFIG_SYS_SDIO2_MAX_CLK 48000000 +#define CONFIG_SYS_SDIO3_MAX_CLK 48000000 +#define CONFIG_SYS_SDIO0 "sdio1" +#define CONFIG_SYS_SDIO1 "sdio2" +#define CONFIG_SYS_SDIO2 "sdio3" +#define CONFIG_SYS_SDIO3 "sdio4" + +/* I2C Driver */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_KONA +#define CONFIG_SYS_SPD_BUS_NUM 3 /* Start with PMU bus */ +#define CONFIG_SYS_MAX_I2C_BUS 4 +#define CONFIG_SYS_I2C_BASE0 BSC1_BASE_ADDR +#define CONFIG_SYS_I2C_BASE1 BSC2_BASE_ADDR +#define CONFIG_SYS_I2C_BASE2 BSC3_BASE_ADDR +#define CONFIG_SYS_I2C_BASE3 PMU_BSC_BASE_ADDR + +/* Timer Driver */ +#define CONFIG_SYS_TIMER_RATE 32000 +#define CONFIG_SYS_TIMER_COUNTER (TIMER_BASE_ADDR + 4) /* STCLO offset */ + +/* Init functions */ +#define CONFIG_MISC_INIT_R /* board's misc_init_r function */ + +/* Some commands use this as the default load address */ +#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE + +/* No mtest functions as recommended */ +#undef CONFIG_CMD_MEMORY + +/* + * This is the initial SP which is used only briefly for relocating the u-boot + * image to the top of SDRAM. After relocation u-boot moves the stack to the + * proper place. + */ +#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE + +/* Serial Info */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +/* Post pad 3 bytes after each reg addr */ +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK 13000000 +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550_COM1 0x3e000000 + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_ENV_SIZE 0x10000 +#define CONFIG_ENV_IS_NOWHERE + +#define CONFIG_SYS_NO_FLASH /* Not using NAND/NOR unmanaged flash */ + +/* console configuration */ +#define CONFIG_SYS_CBSIZE 1024 /* Console buffer size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) /* Printbuffer size */ +#define CONFIG_SYS_MAXARGS 64 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +/* + * One partition type must be defined for part.c + * This is necessary for the fatls command to work on an SD card + * for example. + */ +#define CONFIG_DOS_PARTITION + +/* version string, parser, etc */ +#define CONFIG_VERSION_VARIABLE +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_CMDLINE_EDITING +#define CONFIG_SYS_LONGHELP + +#define CONFIG_CRC32_VERIFY +#define CONFIG_MX_CYCLIC + +/* Initial upstream - boot to cmd prompt only */ +#define CONFIG_BOOTCOMMAND "" + +/* Commands */ +#include <config_cmd_default.h> +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_FAT +#define CONFIG_CMD_GPIO +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MMC +#define CONFIG_CMD_BOOTZ +#define CONFIG_FAT_WRITE + +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_NFS + +#endif /* __BCM28155_AP_H */ diff --git a/include/configs/bf609-ezkit.h b/include/configs/bf609-ezkit.h index 1a43e1b433..12192ffb5d 100644 --- a/include/configs/bf609-ezkit.h +++ b/include/configs/bf609-ezkit.h @@ -72,12 +72,13 @@ #define CONFIG_NET_MULTI #define CONFIG_HOSTNAME "bf609-ezkit" #define CONFIG_DESIGNWARE_ETH +#define CONFIG_PHY_ADDR 1 #define CONFIG_DW_PORTS 1 -#define CONFIG_DW_AUTONEG #define CONFIG_DW_ALTDESCRIPTOR #define CONFIG_CMD_NET #define CONFIG_CMD_MII #define CONFIG_MII +#define CONFIG_PHYLIB /* i2c Settings */ #define CONFIG_BFIN_TWI_I2C diff --git a/include/configs/bur_am335x_common.h b/include/configs/bur_am335x_common.h new file mode 100644 index 0000000000..7bbe5964ae --- /dev/null +++ b/include/configs/bur_am335x_common.h @@ -0,0 +1,196 @@ +/* + * bur_am335x_common.h + * + * common parts used by B&R AM335x based boards + * + * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> - + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __BUR_AM335X_COMMON_H__ +#define __BUR_AM335X_COMMON_H__ +/* ------------------------------------------------------------------------- */ +#define CONFIG_AM33XX +#define CONFIG_OMAP +#define CONFIG_OMAP_COMMON +#define CONFIG_BOARD_LATE_INIT +#define CONFIG_SYS_CACHELINE_SIZE 64 +#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ + +/* Timer information */ +#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ +#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */ + +#define CONFIG_SPL_POWER_SUPPORT +#define CONFIG_POWER_TPS65217 + +#define CONFIG_SYS_NO_FLASH /* have no NOR-flash */ + +#include <asm/arch/omap.h> + +/* NS16550 Configuration */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK 48000000 +#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */ +#define CONFIG_BAUDRATE 115200 + +/* Network defines */ +#define CONFIG_CMD_NET /* 'bootp' and 'tftp' */ +#define CONFIG_CMD_DHCP +#define CONFIG_BOOTP_DNS /* Configurable parts of CMD_DHCP */ +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_NET_RETRY_COUNT 4 +#define CONFIG_CMD_PING +#define CONFIG_DRIVER_TI_CPSW /* Driver for IP block */ +#define CONFIG_MII /* Required in net/eth.c */ +#define CONFIG_SPL_ETH_SUPPORT +#define CONFIG_PHYLIB +#define CONFIG_PHY_NATSEMI +#define CONFIG_SPL_NET_SUPPORT +#define CONFIG_SPL_ENV_SUPPORT /* used for a fetching MAC-Address */ +#define CONFIG_SPL_NET_VCI_STRING "AM335x U-Boot SPL" + +/* + * SPL related defines. The Public RAM memory map the ROM defines the + * area between 0x402F0400 and 0x4030B800 as a download area and + * 0x4030B800 to 0x4030CE00 as a public stack area. The ROM also + * supports X-MODEM loading via UART, and we leverage this and then use + * Y-MODEM to load u-boot.img, when booted over UART. + */ +#define CONFIG_SPL_TEXT_BASE 0x402F0400 +#define CONFIG_SPL_MAX_SIZE (0x4030B800 - CONFIG_SPL_TEXT_BASE) + +/* + * Since SPL did pll and ddr initialization for us, + * we don't need to do it twice. + */ +#if !defined(CONFIG_SPL_BUILD) && !defined(CONFIG_NOR_BOOT) +#define CONFIG_SKIP_LOWLEVEL_INIT +#endif /* !CONFIG_SPL_BUILD, ... */ +/* + * Our DDR memory always starts at 0x80000000 and U-Boot shall have + * relocated itself to higher in memory by the time this value is used. + */ +#define CONFIG_SYS_LOAD_ADDR 0x80000000 +/* + * ---------------------------------------------------------------------------- + * DDR information. We say (for simplicity) that we have 1 bank, + * always, even when we have more. We always start at 0x80000000, + * and we place the initial stack pointer in our SRAM. + */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \ + GENERATED_GBL_DATA_SIZE) + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP24XX + +/* GPIO */ +#define CONFIG_OMAP_GPIO +#define CONFIG_CMD_GPIO +/* + * ---------------------------------------------------------------------------- + * The following are general good-enough settings for U-Boot. We set a + * large malloc pool as we generally have a lot of DDR, and we opt for + * function over binary size in the main portion of U-Boot as this is + * generally easily constrained later if needed. We enable the config + * options that give us information in the environment about what board + * we are on so we do not need to rely on the command prompt. We set a + * console baudrate of 115200 and use the default baud rate table. + */ +#define CONFIG_SYS_MALLOC_LEN (1024 << 10) +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT "U-Boot (BuR V2.0)# " +#define CONFIG_SYS_CONSOLE_INFO_QUIET +#define CONFIG_ENV_OVERWRITE /* Overwrite ethaddr / serial# */ + +/* As stated above, the following choices are optional. */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_AUTO_COMPLETE +#define CONFIG_CMDLINE_EDITING +#define CONFIG_VERSION_VARIABLE + +/* We set the max number of command args high to avoid HUSH bugs. */ +#define CONFIG_SYS_MAXARGS 64 + +/* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 512 +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE +\ + sizeof(CONFIG_SYS_PROMPT) + 16) +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +/* + * For commands to use, we take the default list and add a few other + * useful commands. Note that we must have set CONFIG_SYS_NO_FLASH + * prior to this include, in order to skip a few commands. When we do + * have flash, if we expect these commands they must be enabled in that + * config. If desired, a specific list of desired commands can be used + * instead. + */ +#include <config_cmd_default.h> +/* undefine commands, which we do not need */ +#undef CONFIG_CMD_EDITENV +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_ITEST +#undef CONFIG_CMD_LOADS +#undef CONFIG_CMD_LOADB +#undef CONFIG_CMD_NFS +#undef CONFIG_CMD_SETGETDCR +#undef CONFIG_CMD_XIMG +#undef CONFIG_CMD_CRC32 +/* define command we need always */ +#define CONFIG_CMD_ECHO +#define CONFIG_CMD_SOURCE + +/* + * Our platforms make use of SPL to initalize the hardware (primarily + * memory) enough for full U-Boot to be loaded. We also support Falcon + * Mode so that the Linux kernel can be booted directly from SPL + * instead, if desired. We make use of the general SPL framework found + * under common/spl/. Given our generally common memory map, we set a + * number of related defaults and sizes here. + */ +#define CONFIG_SPL +#define CONFIG_SPL_FRAMEWORK +/* + * Place the image at the start of the ROM defined image space. + * We limit our size to the ROM-defined downloaded image area, and use the + * rest of the space for stack. We load U-Boot itself into memory at + * 0x80800000 for legacy reasons (to not conflict with older SPLs). We + * have our BSS be placed 1MiB after this, to allow for the default + * Linux kernel address of 0x80008000 to work, in the Falcon Mode case. + * We have the SPL malloc pool at the end of the BSS area. + * + * ---------------------------------------------------------------------------- + */ +#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR +#undef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0x80800000 +#define CONFIG_SPL_BSS_START_ADDR 0x80A00000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ +#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ + CONFIG_SPL_BSS_MAX_SIZE) +#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN + +/* General parts of the framework, required. */ +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SPL_YMODEM_SUPPORT +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds" + +#endif /* ! __BUR_AM335X_COMMON_H__ */ diff --git a/include/configs/cardhu.h b/include/configs/cardhu.h index 4abb03ea56..e80d1a6fa3 100644 --- a/include/configs/cardhu.h +++ b/include/configs/cardhu.h @@ -30,6 +30,10 @@ #define V_PROMPT "Tegra30 (Cardhu) # " #define CONFIG_TEGRA_BOARD_STRING "NVIDIA Cardhu" +#define BOARD_EXTRA_ENV_SETTINGS \ + "board_name=cardhu-a04\0" \ + "fdtfile=tegra30-cardhu-a04.dtb\0" + /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI #define CONFIG_TEGRA_ENABLE_UARTA diff --git a/include/configs/cm_t335.h b/include/configs/cm_t335.h index 56e9a8e0e8..26b615b8c5 100644 --- a/include/configs/cm_t335.h +++ b/include/configs/cm_t335.h @@ -114,7 +114,6 @@ /* Network. */ #define CONFIG_PHY_GIGE #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_ATHEROS /* NAND support */ diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h index 7729a02ab6..08c67f588c 100644 --- a/include/configs/cm_t35.h +++ b/include/configs/cm_t35.h @@ -45,13 +45,6 @@ #define CONFIG_MISC_INIT_R #define CONFIG_OF_LIBFDT 1 -/* - * The early kernel mapping on ARM currently only maps from the base of DRAM - * to the end of the kernel image. The kernel is loaded at DRAM base + 0x8000. - * The early kernel pagetable uses DRAM base + 0x4000 to DRAM base + 0x8000, - * so that leaves DRAM base to DRAM base + 0x4000 available. - */ -#define CONFIG_SYS_BOOTMAPSZ 0x4000 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ #define CONFIG_SETUP_MEMORY_TAGS diff --git a/include/configs/corvus.h b/include/configs/corvus.h index 11ba4cffc4..959e188d9a 100644 --- a/include/configs/corvus.h +++ b/include/configs/corvus.h @@ -33,7 +33,6 @@ /* ARM asynchronous clock */ #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 #define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */ -#define CONFIG_SYS_HZ 1000 #define CONFIG_AT91FAMILY diff --git a/include/configs/devkit3250.h b/include/configs/devkit3250.h index bcb21fefe3..3d39b10658 100644 --- a/include/configs/devkit3250.h +++ b/include/configs/devkit3250.h @@ -29,7 +29,6 @@ */ #define CONFIG_NR_DRAM_BANKS 1 #define CONFIG_SYS_MALLOC_LEN SZ_1M -#define CONFIG_SYS_GBL_DATA_SIZE 128 #define CONFIG_SYS_SDRAM_BASE EMC_DYCS0_BASE #define CONFIG_SYS_SDRAM_SIZE SZ_64M #define CONFIG_SYS_TEXT_BASE 0x83FA0000 diff --git a/include/configs/dlvision-10g.h b/include/configs/dlvision-10g.h index 31fc65d196..78778970f4 100644 --- a/include/configs/dlvision-10g.h +++ b/include/configs/dlvision-10g.h @@ -217,9 +217,8 @@ #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* in SDRAM */ #define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size/bytes res'd for init data*/ #define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) + (CONFIG_SYS_INIT_RAM_END - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h index 04ae3ca41d..291c538a34 100644 --- a/include/configs/dra7xx_evm.h +++ b/include/configs/dra7xx_evm.h @@ -34,8 +34,19 @@ #define CONFIG_SYS_OMAP_ABE_SYSCK +/* Define the default GPT table for eMMC */ +#define PARTS_DEFAULT \ + "uuid_disk=${uuid_gpt_disk};" \ + "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}" + #include <configs/ti_omap5_common.h> +/* Enhance our eMMC support / experience. */ +#define CONFIG_CMD_GPT +#define CONFIG_EFI_PARTITION +#define CONFIG_PARTITION_UUIDS +#define CONFIG_CMD_PART + /* CPSW Ethernet */ #define CONFIG_CMD_NET /* 'bootp' and 'tftp' */ #define CONFIG_CMD_DHCP @@ -51,7 +62,6 @@ #define CONFIG_MII /* Required in net/eth.c */ #define CONFIG_PHY_GIGE /* per-board part of CPSW */ #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 2 /* SPI */ #undef CONFIG_OMAP3_SPI @@ -73,6 +83,8 @@ #define CONFIG_SPL_SPI_CS 0 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 +#define CONFIG_SUPPORT_EMMC_BOOT + /* USB xHCI HOST */ #define CONFIG_CMD_USB #define CONFIG_USB_HOST diff --git a/include/configs/dvlhost.h b/include/configs/dvlhost.h deleted file mode 100644 index 1af7f16989..0000000000 --- a/include/configs/dvlhost.h +++ /dev/null @@ -1,222 +0,0 @@ -/* - * (C) Copyright 2009 - * Michael Schwingen, michael@schwingen.org - * - * Configuration settings for the - * dLAN200 AV Wireless G ("dvlhost") board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_IXP425 1 -#define CONFIG_DVLHOST 1 - -#define CONFIG_MACH_TYPE 1343 - -#define CONFIG_DISPLAY_CPUINFO 1 -#define CONFIG_DISPLAY_BOARDINFO 1 - -#define CONFIG_IXP_SERIAL -#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART2 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 3 -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_BOARD_EARLY_INIT_F 1 -#define CONFIG_SYS_LDSCRIPT "board/dvlhost/u-boot.lds" - -/*************************************************************** - * U-boot generic defines start here. - ***************************************************************/ -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* Command line configuration. */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ELF -#define CONFIG_PCI -#ifdef CONFIG_PCI -#define CONFIG_CMD_PCI -#define CONFIG_PCI_PNP -#define CONFIG_IXP_PCI -#define CONFIG_PCI_SCAN_SHOW -#define CONFIG_CMD_PCI_ENUM -#endif - -#define CONFIG_BOOTCOMMAND "run boot_flash" -/* enable passing of ATAGs */ -#define CONFIG_CMDLINE_TAG 1 -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_KGDB_BAUDRATE 230400 -#endif - -/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP -/* Console I/O Buffer Size */ -#define CONFIG_SYS_CBSIZE 256 -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -/* max number of command args */ -#define CONFIG_SYS_MAXARGS 16 -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x00000000 -#define CONFIG_SYS_MEMTEST_END 0x01D80000 - -/* timer clock - 2* OSC_IN system clock */ -#define CONFIG_IXP425_TIMER_CLK 66666666 - -/* default load address */ -#define CONFIG_SYS_LOAD_ADDR 0x00010000 - -/* valid baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200, 230400 } -#define CONFIG_SERIAL_RTS_ACTIVE 1 - -/* Expansion bus settings */ -#define CONFIG_SYS_EXP_CS0 0xbd113442 - -/* SDRAM settings */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM_1 0x00000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -/* 32MB SDRAM: 2* 8Mx16, CL3 */ -#define CONFIG_SYS_SDR_CONFIG 0x18 -#define PHYS_SDRAM_1_SIZE 0x02000000 -#define CONFIG_SYS_SDRAM_REFRESH_CNT 0x800 -#define CONFIG_SYS_SDR_MODE_CONFIG 0x1 -#define CONFIG_SYS_DRAM_SIZE PHYS_SDRAM_1_SIZE - -/* FLASH organization: one Spansion S29AL032D-04 Flash */ -#define CONFIG_SYS_TEXT_BASE 0x50000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -/* max number of sectors on one chip */ -#define CONFIG_SYS_MAX_FLASH_SECT 140 -#define PHYS_FLASH_1 0x50000000 -#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1 } - -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) -#define CONFIG_BOARD_SIZE_LIMIT 262144 - -/* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -/* no byte writes on IXP4xx */ -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT - -/* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_EMPTY_INFO - -/* Ethernet */ - -/* include IXP4xx NPE support */ -#define CONFIG_IXP4XX_NPE 1 - -/* NPE0 PHY: MII dLAN200 AVmodule, 100BaseT-FDX fixed */ -#define CONFIG_PHY_ADDR 0x18 -/* NPE1 PHY: MII IP175 switch, port 5 is host port */ -#define CONFIG_PHY1_ADDR 0x05 -/* MII PHY management */ -#define CONFIG_MII 1 -/* fixed-speed powerline modem without standard PHY registers on MII */ -#define CONFIG_MII_NPE0_FIXEDLINK 1 -#define CONFIG_MII_NPE0_SPEED 100 -#define CONFIG_MII_NPE0_FULLDUPLEX 1 -/* fixed-speed switch without standard PHY registers on MII */ -#define CONFIG_MII_NPE1_FIXEDLINK 1 -#define CONFIG_MII_NPE1_SPEED 100 -#define CONFIG_MII_NPE1_FULLDUPLEX 1 - -/* Number of ethernet rx buffers & descriptors */ -#define CONFIG_SYS_RX_ETH_BUFFER 16 -#define CONFIG_RESET_PHY_R 1 -/* ethernet switch connected to MII port */ -#define CONFIG_MII_ETHSWITCH 1 -#define CONFIG_HAS_ETH1 1 - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_NET -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#undef CONFIG_CMD_NFS - -/* BOOTP options */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 32 - -/* - * environment organization: - * one flash sector, embedded in uboot area (bottom bootblock flash) - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x4000) -#define CONFIG_SYS_USE_PPCENV 1 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "npe_ucode=50040000\0" \ - "ethprime=NPE1\0" \ - "ethrotate=no\0" \ - "mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root),\0" \ - "kerneladdr=50050000\0" \ - "kernelfile=dvlhost/uImage\0" \ - "rootfile=dvlhost/rootfs\0" \ - "rootaddr=50170000\0" \ - "loadaddr=10000\0" \ - "updateboot_ser=mw.b 10000 ff 40000;" \ - " loady ${loadaddr};" \ - " run eraseboot writeboot\0" \ - "updateboot_net=mw.b 10000 ff 40000;" \ - " tftp ${loadaddr} dvlhost/u-boot.bin;" \ - " run eraseboot writeboot\0" \ - "eraseboot=protect off 50000000 50003fff;" \ - " protect off 50006000 5003ffff;" \ - " erase 50000000 50003fff;" \ - " erase 50006000 5003ffff\0" \ - "writeboot=cp.b 10000 50000000 4000;" \ - " cp.b 16000 50006000 3a000\0" \ - "updateucode=loady;" \ - " era ${npe_ucode} +${filesize};" \ - " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ - "updateroot=tftp ${loadaddr} ${rootfile};" \ - " era ${rootaddr} +${filesize};" \ - " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ - "updatekern=tftp ${loadaddr} ${kernelfile};" \ - " era ${kerneladdr} +${filesize};" \ - " cp.b ${loadaddr} ${kerneladdr} ${filesize}\0" \ - "flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ - "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \ - "boot_flash=run flashargs addtty addeth;" \ - " bootm ${kerneladdr}\0" \ - "boot_net=run netargs addtty addeth;" \ - " tftpboot ${loadaddr} ${kernelfile};" \ - " bootm\0" - -/* additions for new relocation code, must be added to all boards */ -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) - -#endif /* __CONFIG_H */ diff --git a/include/configs/dxr2.h b/include/configs/dxr2.h index 1e42f5c23c..75f7812e7d 100644 --- a/include/configs/dxr2.h +++ b/include/configs/dxr2.h @@ -26,6 +26,7 @@ #define BOARD_DFU_BUTTON_GPIO 27 #define BOARD_DFU_BUTTON_LED 64 +#define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */ #undef CONFIG_DOS_PARTITION #undef CONFIG_CMD_FAT @@ -49,7 +50,6 @@ #undef CONFIG_MII #undef CONFIG_PHY_GIGE -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_SMSC #define CONFIG_FACTORYSET diff --git a/include/configs/ecovec.h b/include/configs/ecovec.h index 3a5cc74829..e26591c14f 100644 --- a/include/configs/ecovec.h +++ b/include/configs/ecovec.h @@ -158,8 +158,6 @@ #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Size of DRAM reserved for malloc() use */ #define CONFIG_SYS_MALLOC_LEN (256 * 1024) -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE (256) #define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) /* ENV setting */ diff --git a/include/configs/hummingboard.h b/include/configs/hummingboard.h index ac65620db6..6bf3408dd0 100644 --- a/include/configs/hummingboard.h +++ b/include/configs/hummingboard.h @@ -190,7 +190,6 @@ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_SYS_HZ 1000 #define CONFIG_CMDLINE_EDITING diff --git a/include/configs/io.h b/include/configs/io.h index 7f86767e94..9da6cc6855 100644 --- a/include/configs/io.h +++ b/include/configs/io.h @@ -198,9 +198,8 @@ #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* in SDRAM */ #define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size/bytes res'd for init data*/ #define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) + (CONFIG_SYS_INIT_RAM_END - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* diff --git a/include/configs/iocon.h b/include/configs/iocon.h index d34b91dfde..f36c2a3504 100644 --- a/include/configs/iocon.h +++ b/include/configs/iocon.h @@ -238,9 +238,8 @@ int fpga_gpio_get(unsigned int bus, int pin); #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* in SDRAM */ #define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size/bytes res'd for init data*/ #define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) + (CONFIG_SYS_INIT_RAM_END - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* diff --git a/include/configs/km/keymile-common.h b/include/configs/km/keymile-common.h index 2a15ad469b..517f46a3a3 100644 --- a/include/configs/km/keymile-common.h +++ b/include/configs/km/keymile-common.h @@ -99,11 +99,16 @@ #define CONFIG_KM_UBI_PARTITION_NAME_BOOT "ubi0" #endif /* CONFIG_KM_UBI_PARTITION_NAME_BOOT */ +#ifndef CONFIG_KM_UBI_PART_BOOT_OPTS +#define CONFIG_KM_UBI_PART_BOOT_OPTS "" +#endif /* CONFIG_KM_UBI_PART_BOOT_OPTS */ + #ifndef CONFIG_KM_UBI_PARTITION_NAME_APP /* one flash chip only called boot */ /* boot: CONFIG_KM_UBI_PARTITION_NAME_BOOT */ # define CONFIG_KM_UBI_LINUX_MTD \ - "ubi.mtd=" CONFIG_KM_UBI_PARTITION_NAME_BOOT + "ubi.mtd=" CONFIG_KM_UBI_PARTITION_NAME_BOOT \ + CONFIG_KM_UBI_PART_BOOT_OPTS # define CONFIG_KM_DEV_ENV_FLASH_BOOT_UBI \ "ubiattach=ubi part " CONFIG_KM_UBI_PARTITION_NAME_BOOT "\0" #else /* CONFIG_KM_UBI_PARTITION_NAME_APP */ @@ -111,7 +116,8 @@ /* boot: CONFIG_KM_UBI_PARTITION_NAME_BOOT */ /* app: CONFIG_KM_UBI_PARTITION_NAME_APP */ # define CONFIG_KM_UBI_LINUX_MTD \ - "ubi.mtd=" CONFIG_KM_UBI_PARTITION_NAME_BOOT " " \ + "ubi.mtd=" CONFIG_KM_UBI_PARTITION_NAME_BOOT \ + CONFIG_KM_UBI_PART_BOOT_OPTS " " \ "ubi.mtd=" CONFIG_KM_UBI_PARTITION_NAME_APP # define CONFIG_KM_DEV_ENV_FLASH_BOOT_UBI \ "ubiattach=if test ${boot_bank} -eq 0; then; " \ @@ -135,8 +141,8 @@ * - 'release': for a standalone system kernel/rootfs from flash */ #define CONFIG_KM_DEF_ENV_BOOTTARGETS \ - "subbootcmds=ubiattach ubicopy cramfsloadfdt cramfsloadkernel " \ - "flashargs add_default addpanic boot\0" \ + "subbootcmds=ubiattach ubicopy cramfsloadfdt set_fdthigh " \ + "cramfsloadkernel flashargs add_default addpanic boot\0"\ "develop=" \ "tftp 200000 scripts/develop-${arch}.txt && " \ "env import -t 200000 ${filesize} && " \ @@ -220,6 +226,7 @@ CONFIG_KM_DEF_ENV_FLASH_BOOT \ CONFIG_KM_DEF_ENV_CONSTANTS \ "altbootcmd=run bootcmd\0" \ + "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \ "bootcmd=km_checkbidhwk && " \ "setenv bootcmd \'if km_checktestboot; then; " \ "setenv boot_bank ${test_bank}; else; " \ @@ -229,6 +236,10 @@ "run ${subbootcmds}; reset\' && " \ "saveenv && saveenv && boot\0" \ "bootlimit=3\0" \ + "cramfsloadfdt=" \ + "cramfsload ${fdt_addr_r} " \ + "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \ + "fdt_addr_r="__stringify(CONFIG_KM_FDT_ADDR) "\0" \ "init=/sbin/init-overlay.sh\0" \ "load_addr_r="__stringify(CONFIG_KM_KERNEL_ADDR) "\0" \ "load=tftpboot ${load_addr_r} ${u-boot}\0" \ diff --git a/include/configs/km/km-powerpc.h b/include/configs/km/km-powerpc.h index 2cebb2bb0c..763c5bad82 100644 --- a/include/configs/km/km-powerpc.h +++ b/include/configs/km/km-powerpc.h @@ -70,11 +70,6 @@ #define CONFIG_KM_DEF_BOOT_ARGS_CPU "" #define CONFIG_KM_DEF_ENV_CPU \ - "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \ - "cramfsloadfdt=" \ - "cramfsload ${fdt_addr_r} " \ - "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \ - "fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \ "u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.bin\0" \ "update=" \ "protect off " __stringify(BOOTFLASH_START) " +${filesize} && "\ @@ -82,6 +77,7 @@ "cp.b ${load_addr_r} " __stringify(BOOTFLASH_START) \ " ${filesize} && " \ "protect on " __stringify(BOOTFLASH_START) " +${filesize}\0"\ + "set_fdthigh=true\0" \ "" #endif /* __CONFIG_KEYMILE_POWERPC_H */ diff --git a/include/configs/km/km83xx-common.h b/include/configs/km/km83xx-common.h index 5e075c8dd2..ae6b6dcf24 100644 --- a/include/configs/km/km83xx-common.h +++ b/include/configs/km/km83xx-common.h @@ -84,7 +84,6 @@ #define CONFIG_SYS_INIT_RAM_LOCK #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ GENERATED_GBL_DATA_SIZE) diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h index e74f85f604..6d77680c82 100644 --- a/include/configs/km/km_arm.h +++ b/include/configs/km/km_arm.h @@ -70,7 +70,8 @@ #define CONFIG_KM_PHRAM 0x17F000 #define CONFIG_KM_CRAMFS_ADDR 0x2400000 -#define CONFIG_KM_KERNEL_ADDR 0x2000000 /* 4096KBytes */ +#define CONFIG_KM_KERNEL_ADDR 0x2000000 /* 3098KBytes */ +#define CONFIG_KM_FDT_ADDR 0x23E0000 /* 128KBytes */ /* architecture specific default bootargs */ #define CONFIG_KM_DEF_BOOT_ARGS_CPU \ @@ -78,15 +79,17 @@ " boardid=0x${IVM_BoardId} hwkey=0x${IVM_HWKey}" #define CONFIG_KM_DEF_ENV_CPU \ - "boot=bootm ${load_addr_r} - -\0" \ - "cramfsloadfdt=true\0" \ "u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.kwb\0" \ CONFIG_KM_UPDATE_UBOOT \ + "set_fdthigh=setenv fdt_high ${kernelmem}\0" \ "" #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ #define CONFIG_MISC_INIT_R +/* Pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT + /* * NS16550 Configuration */ @@ -289,10 +292,15 @@ int get_scl(void); " ${addr} " __stringify(CONFIG_ENV_OFFSET_REDUND) " 4\0" #endif +#ifndef CONFIG_KM_BOARD_EXTRA_ENV +#define CONFIG_KM_BOARD_EXTRA_ENV "" +#endif + /* * Default environment variables */ #define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_KM_BOARD_EXTRA_ENV \ CONFIG_KM_DEF_ENV \ CONFIG_KM_NEW_ENV \ "arch=arm\0" \ diff --git a/include/configs/km/kmp204x-common.h b/include/configs/km/kmp204x-common.h index 2466649b15..0d24f78d42 100644 --- a/include/configs/km/kmp204x-common.h +++ b/include/configs/km/kmp204x-common.h @@ -15,6 +15,10 @@ #define CONFIG_KM_DEF_NETDEV "netdev=eth0\0" +/* an additionnal option is required for UBI as subpage access is + * supported in u-boot */ +#define CONFIG_KM_UBI_PART_BOOT_OPTS ",2048" + #define CONFIG_NAND_ECC_BCH /* common KM defines */ @@ -148,8 +152,6 @@ unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */ #define CONFIG_KM_FDT_ADDR 0x1F80000 /* max dtb size 0.5Mbytes */ -#define CONFIG_BOOTCOUNT_LIMIT - /* * Local Bus Definitions */ @@ -206,8 +208,13 @@ unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */ #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */ +/* bootcounter in QRIO */ +#define CONFIG_BOOTCOUNT_LIMIT +#define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SYS_QRIO_BASE + 0x20) + #define CONFIG_BOARD_EARLY_INIT_F #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ +#define CONFIG_MISC_INIT_F #define CONFIG_MISC_INIT_R #define CONFIG_LAST_STAGE_INIT @@ -263,7 +270,10 @@ unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ + #define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_INIT_BOARD +#define CONFIG_SYS_I2C_SPEED 100000 /* deblocking */ #define CONFIG_SYS_NUM_I2C_BUSES 3 #define CONFIG_SYS_I2C_MAX_HOPS 1 #define CONFIG_SYS_I2C_FSL /* Use FSL I2C driver */ @@ -276,6 +286,12 @@ unsigned long get_board_sys_clk(unsigned long dummy); {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \ {0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \ } +#ifndef __ASSEMBLY__ +void set_sda(int state); +void set_scl(int state); +int get_sda(void); +int get_scl(void); +#endif #define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/ @@ -286,6 +302,7 @@ unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SPI_FLASH #define CONFIG_SPI_FLASH_BAR /* 4 byte-addressing */ #define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SPI_FLASH_SPANSION #define CONFIG_CMD_SF #define CONFIG_SF_DEFAULT_SPEED 20000000 #define CONFIG_SF_DEFAULT_MODE 0 @@ -420,6 +437,7 @@ unsigned long get_board_sys_clk(unsigned long dummy); "update=" \ "sf probe 0;sf erase 0 +${filesize};" \ "sf write ${load_addr_r} 0 ${filesize};\0" \ + "set_fdthigh=true\0" \ "" #define CONFIG_HW_ENV_SETTINGS \ diff --git a/include/configs/km_kirkwood.h b/include/configs/km_kirkwood.h index 74c72325f6..2cde1770cd 100644 --- a/include/configs/km_kirkwood.h +++ b/include/configs/km_kirkwood.h @@ -45,11 +45,19 @@ #define CONFIG_KM_DISABLE_PCIE #define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ -/* KM_NUSA */ -#elif defined(CONFIG_KM_NUSA) +/* KM_NUSA / KM_SUGP1 */ +#elif defined(CONFIG_KM_NUSA) || defined(CONFIG_KM_SUGP1) #define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ + +# if defined(CONFIG_KM_NUSA) #define CONFIG_IDENT_STRING "\nKeymile NUSA" #define CONFIG_HOSTNAME kmnusa +# elif defined(CONFIG_KM_SUGP1) +#define CONFIG_IDENT_STRING "\nKeymile SUGP1" +#define CONFIG_HOSTNAME kmsugp1 +#define KM_PCIE_RESET_MPP7 +#endif + #undef CONFIG_SYS_KWD_CONFIG #define CONFIG_SYS_KWD_CONFIG \ $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage_128M16_1.cfg @@ -97,6 +105,9 @@ #define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ #define CONFIG_IDENT_STRING "\nKeymile SUV31" #define CONFIG_HOSTNAME kmsuv31 +#undef CONFIG_SYS_KWD_CONFIG +#define CONFIG_SYS_KWD_CONFIG \ + $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage_128M16_1.cfg #define CONFIG_KM_ENV_IS_IN_SPI_NOR #define CONFIG_KM_FPGA_CONFIG diff --git a/include/configs/kmp204x.h b/include/configs/kmp204x.h index 4158c8dd0f..8bb3571691 100644 --- a/include/configs/kmp204x.h +++ b/include/configs/kmp204x.h @@ -13,6 +13,11 @@ #define CONFIG_HOSTNAME kmlion1 #define CONFIG_KM_BOARD_NAME "kmlion1" +/* KMCOGE4 */ +#elif defined(CONFIG_KMCOGE4) +#define CONFIG_HOSTNAME kmcoge4 +#define CONFIG_KM_BOARD_NAME "kmcoge4" + #else #error ("Board not supported") #endif @@ -42,6 +47,7 @@ #define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_LBAPP1_BR_PRELIM /* Local bus app1 Options */ #define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_LBAPP1_OR_PRELIM +#endif /* App2 Local bus */ #define CONFIG_SYS_LBAPP2_BASE 0xE0000000 @@ -63,6 +69,5 @@ #define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_LBAPP2_BR_PRELIM /* Local bus app2 Options */ #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_LBAPP2_OR_PRELIM -#endif #endif /* __CONFIG_H */ diff --git a/include/configs/koelsch.h b/include/configs/koelsch.h index cc3c7a8e6a..90e2d7a030 100644 --- a/include/configs/koelsch.h +++ b/include/configs/koelsch.h @@ -106,7 +106,6 @@ #define CONFIG_SYS_MONITOR_BASE 0x00000000 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) #define CONFIG_SYS_MALLOC_LEN (1 * 1024 * 1024) -#define CONFIG_SYS_GBL_DATA_SIZE (256) #define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) /* FLASH */ @@ -171,7 +170,6 @@ #define CONFIG_SH_TMU_CLK_FREQ CONFIG_SYS_CLK_FREQ #define CONFIG_SH_SCIF_CLK_FREQ 14745600 #define CONFIG_SYS_TMU_CLK_DIV 4 -#define CONFIG_SYS_HZ 1000 /* i2c */ #define CONFIG_CMD_I2C diff --git a/include/configs/kwb.h b/include/configs/kwb.h new file mode 100644 index 0000000000..0f631c0f60 --- /dev/null +++ b/include/configs/kwb.h @@ -0,0 +1,128 @@ +/* + * kwb.h + * + * specific parts for B&R KWB Motherboard + * + * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> - + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_KWB_H__ +#define __CONFIG_KWB_H__ + +#include <configs/bur_am335x_common.h> +/* ------------------------------------------------------------------------- */ +/* Clock Defines */ +#define V_OSCK 26000000 /* Clock output from T2 */ +#define V_SCLK (V_OSCK) + +#define CONFIG_POWER_TPS65217 + +#define CONFIG_MACH_TYPE 3589 +/* I2C IP block */ +#define CONFIG_SYS_OMAP24_I2C_SPEED_PSOC 20000 + +/* GPIO */ +#define CONFIG_SPL_GPIO_SUPPORT + +/* MMC/SD IP block */ +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_OMAP_HSMMC +#define CONFIG_CMD_MMC +#define CONFIG_SUPPORT_EMMC_BOOT +/* RAW SD card / eMMC locations. */ +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /*addr. 0x60000 */ +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ +#define CONFIG_SPL_MMC_SUPPORT + +#undef CONFIG_SPL_OS_BOOT +#ifdef CONFIG_SPL_OS_BOOT +#define CONFIG_SYS_SPL_ARGS_ADDR 0x80F80000 + +/* RAW SD card / eMMC */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */ + +#endif /* CONFIG_SPL_OS_BOOT */ + +/* Always 128 KiB env size */ +#define CONFIG_ENV_SIZE (128 << 10) + +#ifndef CONFIG_SPL_BUILD +#define CONFIG_EXTRA_ENV_SETTINGS \ + "autoload=0\0" \ + "loadaddr=0x80100000\0" \ + "bootfile=arimg\0" \ + "usbboot=echo Booting from USB-Stick ...; " \ + "usb start; " \ + "fatload usb 0 ${loadaddr} ${bootfile}; " \ + "usb stop; " \ + "go ${loadaddr};\0" \ + "netboot=echo Booting from network ...; " \ + "setenv autoload 0; " \ + "dhcp; " \ + "tftp ${loadaddr} arimg; " \ + "go ${loadaddr}\0" \ + "usbupdate=echo Updating UBOOT from USB-Stick ...; " \ + "usb start; " \ + "fatload usb 0 0x80000000 updateubootusb.img; " \ + "source;\0" \ + "netupdate=echo Updating UBOOT from Network (TFTP) ...; " \ + "setenv autoload 0; " \ + "dhcp;" \ + "tftp 0x80000000 updateUBOOT.img;" \ + "source;\0" +#endif /* !CONFIG_SPL_BUILD*/ + +#define CONFIG_BOOTCOMMAND \ + "run usbupdate;" +#define CONFIG_BOOTDELAY 1 /* TODO: für release auf 0 setzen */ + +/* undefine command which we not need here */ +#undef CONFIG_BOOTM_LINUX +#undef CONFIG_BOOTM_NETBSD +#undef CONFIG_BOOTM_PLAN9 +#undef CONFIG_BOOTM_RTEMS +#undef CONFIG_GZIP +#undef CONFIG_ZLIB +#undef CONFIG_CMD_CRC32 + +/* USB configuration */ +#define CONFIG_USB_MUSB_DSPS +#define CONFIG_ARCH_MISC_INIT +#define CONFIG_MUSB_PIO_ONLY +#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT +/* attention! not only for gadget, enables also highspeed in hostmode */ +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_MUSB_HOST +#define CONFIG_AM335X_USB0 +#define CONFIG_AM335X_USB0_MODE MUSB_HOST + +#ifdef CONFIG_MUSB_HOST +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#endif /* CONFIG_MUSB_HOST */ + +#undef CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 1 +#define CONFIG_SYS_MMC_ENV_PART 2 +#define CONFIG_ENV_OFFSET 0x40000 /* TODO: Adresse definieren */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT +/* + * Common filesystems support. When we have removable storage we + * enabled a number of useful commands and support. + */ +#if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE) +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_FAT +#define CONFIG_FAT_WRITE +#define CONFIG_CMD_FS_GENERIC +#endif /* CONFIG_MMC, ... */ + +#endif /* ! __CONFIG_TSERIES_H__ */ diff --git a/include/configs/kzm9g.h b/include/configs/kzm9g.h index f183279ba8..4d11c7d08c 100644 --- a/include/configs/kzm9g.h +++ b/include/configs/kzm9g.h @@ -88,7 +88,6 @@ #define CONFIG_SYS_MONITOR_BASE (KZM_FLASH_BASE) #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024) -#define CONFIG_SYS_GBL_DATA_SIZE (256) #define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) #define CONFIG_SYS_TEXT_BASE 0x00000000 diff --git a/include/configs/lager.h b/include/configs/lager.h index b6c1954a94..b420e45e63 100644 --- a/include/configs/lager.h +++ b/include/configs/lager.h @@ -109,7 +109,6 @@ #define CONFIG_SYS_MONITOR_BASE 0x00000000 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) #define CONFIG_SYS_MALLOC_LEN (1 * 1024 * 1024) -#define CONFIG_SYS_GBL_DATA_SIZE (256) #define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) #if defined(CONFIG_SYS_USE_BOOT_NORFLASH) @@ -196,6 +195,5 @@ #define CONFIG_SH_SCIF_CLK_FREQ CONFIG_MP_CLK_FREQ #define CONFIG_SYS_TMU_CLK_DIV 4 -#define CONFIG_SYS_HZ 1000 #endif /* __LAGER_H */ diff --git a/include/configs/mcx.h b/include/configs/mcx.h index dcd29ce7cb..7c5c2f4d1c 100644 --- a/include/configs/mcx.h +++ b/include/configs/mcx.h @@ -98,6 +98,7 @@ /* EHCI */ #define CONFIG_USB_STORAGE +#define CONFIG_OMAP3_GPIO_2 #define CONFIG_OMAP3_GPIO_5 #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_OMAP @@ -263,10 +264,9 @@ "${mtdparts} " \ "vram=6M omapfb.vram=1:2M,2:2M,3:2M " \ "omapdss.def_disp=lcd;" \ - "bootm 0x82000000 0x84000000\0" - -#define CONFIG_BOOTCOMMAND \ - "run nandboot" + "bootm 0x82000000 0x84000000\0" \ + "bootcmd=mmc rescan;if fatload mmc 0 82000000 loadbootscr.scr;" \ + "then source 82000000;else run nandboot;fi\0" #define CONFIG_AUTO_COMPLETE #define CONFIG_CMDLINE_EDITING @@ -395,6 +395,7 @@ #define CONFIG_SYS_NAND_ECCSIZE 256 #define CONFIG_SYS_NAND_ECCBYTES 3 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW +#define CONFIG_SPL_NAND_SOFTECC #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE diff --git a/include/configs/microblaze-generic.h b/include/configs/microblaze-generic.h index aa8d59d6e9..486787e147 100644 --- a/include/configs/microblaze-generic.h +++ b/include/configs/microblaze-generic.h @@ -200,7 +200,8 @@ # define CONFIG_SYS_MAX_FLASH_SECT 512 /* hardware flash protection */ # define CONFIG_SYS_FLASH_PROTECTION - +/* use buffered writes (20x faster) */ +# define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 # ifdef RAMENV # define CONFIG_ENV_IS_NOWHERE 1 # define CONFIG_ENV_SIZE 0x1000 @@ -446,4 +447,64 @@ # undef CONFIG_PHYLIB #endif +/* SPL part */ +#define CONFIG_SPL +#define CONFIG_CMD_SPL +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_BOARD_INIT + +#define CONFIG_SPL_LDSCRIPT "arch/microblaze/cpu/u-boot-spl.lds" + +#define CONFIG_SPL_RAM_DEVICE +#define CONFIG_SPL_NOR_SUPPORT + +/* for booting directly linux */ +#define CONFIG_SPL_OS_BOOT + +#define CONFIG_SYS_OS_BASE (CONFIG_SYS_FLASH_BASE + \ + 0x60000) +#define CONFIG_SYS_FDT_BASE (CONFIG_SYS_FLASH_BASE + \ + 0x40000) +#define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_TEXT_BASE + \ + 0x1000000) + +/* SP location before relocation, must use scratch RAM */ +/* BRAM start */ +#define CONFIG_SYS_INIT_RAM_ADDR 0x0 +/* BRAM size - will be generated */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 +/* Stack pointer prior relocation, must situated at on-chip RAM */ +#define CONFIG_SYS_SPL_MALLOC_END (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) + +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100 + +/* + * The main reason to do it in this way is that MALLOC_START + * can't be defined - common/spl/spl.c + */ +#if (CONFIG_SYS_SPL_MALLOC_SIZE != 0) +# define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_SPL_MALLOC_END - \ + CONFIG_SYS_SPL_MALLOC_SIZE) +# define CONFIG_SPL_STACK_ADDR CONFIG_SYS_SPL_MALLOC_START +#else +# define CONFIG_SPL_STACK_ADDR CONFIG_SYS_SPL_MALLOC_END +#endif + +/* Just for sure that there is a space for stack */ +#define CONFIG_SPL_STACK_SIZE 0x100 + +#define CONFIG_SYS_UBOOT_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE + +#define CONFIG_SPL_MAX_FOOTPRINT (CONFIG_SYS_INIT_RAM_SIZE - \ + CONFIG_SYS_INIT_RAM_ADDR - \ + GENERATED_GBL_DATA_SIZE - \ + CONFIG_SYS_SPL_MALLOC_SIZE - \ + CONFIG_SPL_STACK_SIZE) + #endif /* __CONFIG_H */ diff --git a/include/configs/mini2440.h b/include/configs/mini2440.h deleted file mode 100644 index 5e9e98d2fc..0000000000 --- a/include/configs/mini2440.h +++ /dev/null @@ -1,170 +0,0 @@ -/* - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger@sysgo.de> - * Gary Jennejohn <gj@denx.de> - * David Mueller <d.mueller@elsoft.ch> - * - * (C) Copyright 2009-2010 - * Michel Pollet <buserror@gmail.com> - * - * (C) Copyright 2012 - * Gabriel Huau <contact@huau-gabriel.fr> - * - * Configuation settings for the MINI2440 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_SYS_TEXT_BASE 0x0 -#define CONFIG_S3C2440_GPIO - -/* - * High Level Configuration Options - */ -#define CONFIG_ARM920T /* This is an ARM920T Core */ -#define CONFIG_S3C24X0 /* in a SAMSUNG S3C24X0 SoC */ -#define CONFIG_S3C2440 /* in a SAMSUNG S3C2440 SoC */ -#define CONFIG_MINI2440 /* on a MIN2440 Board */ - -#define MACH_TYPE_MINI2440 1999 -#define CONFIG_MACH_TYPE MACH_TYPE_MINI2440 - -/* - * We don't use lowlevel_init - */ -#define CONFIG_SKIP_LOWLEVEL_INIT -#define CONFIG_BOARD_EARLY_INIT_F - -/* - * input clock of PLL - */ -/* MINI2440 has 12.0000MHz input clock */ -#define CONFIG_SYS_CLK_FREQ 12000000 - -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048*1024) - -/* - * Hardware drivers - */ -#define CONFIG_DRIVER_DM9000 -#define CONFIG_DRIVER_DM9000_NO_EEPROM -#define CONFIG_DM9000_BASE 0x20000300 -#define DM9000_IO CONFIG_DM9000_BASE -#define DM9000_DATA (CONFIG_DM9000_BASE+4) - -/* - * select serial console configuration - */ -#define CONFIG_S3C24X0_SERIAL -#define CONFIG_SERIAL1 - -/* - * allow to overwrite serial and ethaddr - */ -#define CONFIG_ENV_OVERWRITE - -/* - * Command definition - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_PORTIO -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_SAVES - -/* - * Miscellaneous configurable options - */ -#define CONFIG_LONGHELP -#define CONFIG_SYS_PROMPT "MINI2440 => " -#define CONFIG_SYS_CBSIZE 256 -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 32 -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x30000000 -#define CONFIG_SYS_MEMTEST_END 0x34000000 /* 64MB in DRAM */ - -/* default load address */ -#define CONFIG_SYS_LOAD_ADDR 0x32000000 - -/* boot parameters address */ -#define CONFIG_BOOT_PARAM_ADDR 0x30000100 - -/* - * the PWM TImer 4 uses a counter of 15625 for 10 ms, so we need - * it to wrap 100 times (total 1562500) to get 1 sec. - */ -#define CONFIG_SYS_HZ 1562500 - -/* - * valid baudrates - */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } -#define CONFIG_BAUDRATE 115200 - -/* - * Stack sizes - * The stack sizes are set up in start.S using the settings below - */ -#define CONFIG_STACKSIZE (128*1024) /* regular stack */ -#ifdef CONFIG_USE_IRQ -#define CONFIG_STACKSIZE_IRQ (8*1024) /* IRQ stack */ -#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ -#endif - -/* - * Physical Memory Map - */ -#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ -#define PHYS_SDRAM_SIZE (64*1024*1024) /* 64MB of DRAM */ -#define CONFIG_SYS_SDRAM_BASE 0x30000000 -#define CONFIG_SYS_FLASH_BASE 0x0 - -/* - * Stack should be on the SRAM because - * DRAM is not init - */ -#define CONFIG_SYS_INIT_SP_ADDR (0x40001000 - GENERATED_GBL_DATA_SIZE) - -/* - * NOR FLASH organization - * Now uses the standard CFI interface - * FLASH and environment organization - */ -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT -#define CONFIG_SYS_MONITOR_BASE 0x0 -/* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -/* 512 * 4096 sectors, or 32 * 64k blocks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 -#define CONFIG_FLASH_SHOW_PROGRESS 1 - -/* - * Config for NOR flash - */ -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_MY_ENV_OFFSET 0x40000 -/* addr of environment */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_MY_ENV_OFFSET) -/* 16k Total Size of Environment Sector */ -#define CONFIG_ENV_SIZE 0x4000 - -/* ATAG configuration */ -#define CONFIG_INITRD_TAG -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_CMDLINE_TAG -#define CONFIG_CMDLINE_EDITING -#define CONFIG_AUTO_COMPLETE - -#endif /* __CONFIG_H */ diff --git a/include/configs/mxs.h b/include/configs/mxs.h index 363b277635..55ecef92a9 100644 --- a/include/configs/mxs.h +++ b/include/configs/mxs.h @@ -59,7 +59,6 @@ /* Memory sizes */ #define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Initial data */ #define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ #define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ diff --git a/include/configs/nitrogen6x.h b/include/configs/nitrogen6x.h index e6565518cd..ac517ce25e 100644 --- a/include/configs/nitrogen6x.h +++ b/include/configs/nitrogen6x.h @@ -31,7 +31,7 @@ #define CONFIG_BOARD_EARLY_INIT_F #define CONFIG_MISC_INIT_R #define CONFIG_MXC_GPIO -#define CONFIG_MV_UDC +#define CONFIG_CI_UDC #define CONFIG_USBD_HS #define CONFIG_USB_GADGET_DUALSPEED #define CONFIG_USB_ETHER diff --git a/include/configs/o2dnt-common.h b/include/configs/o2dnt-common.h index 18714eae1e..133dc6f8cd 100644 --- a/include/configs/o2dnt-common.h +++ b/include/configs/o2dnt-common.h @@ -275,10 +275,8 @@ #define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE #endif -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \ - CONFIG_SYS_GBL_DATA_SIZE) + GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE diff --git a/include/configs/omap5_uevm.h b/include/configs/omap5_uevm.h index 51dff23623..783b7c3e32 100644 --- a/include/configs/omap5_uevm.h +++ b/include/configs/omap5_uevm.h @@ -37,6 +37,7 @@ #define CONFIG_PARTITION_UUIDS #define CONFIG_CMD_PART #define CONFIG_HSMMC2_8BIT +#define CONFIG_SUPPORT_EMMC_BOOT /* Required support for the TCA642X GPIO we have on the uEVM */ #define CONFIG_TCA642X diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h index 117484da87..07b61795bb 100644 --- a/include/configs/p1_p2_rdb_pc.h +++ b/include/configs/p1_p2_rdb_pc.h @@ -159,12 +159,12 @@ #define CONFIG_FSL_LAW /* Use common FSL init code */ #define CONFIG_SYS_TEXT_BASE 0x11001000 #define CONFIG_SPL_TEXT_BASE 0xf8f81000 -#define CONFIG_SPL_PAD_TO 0x18000 -#define CONFIG_SPL_MAX_SIZE (96 * 1024) +#define CONFIG_SPL_PAD_TO 0x20000 +#define CONFIG_SPL_MAX_SIZE (128 * 1024) #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) #define CONFIG_SYS_MMC_U_BOOT_DST (0x11000000) #define CONFIG_SYS_MMC_U_BOOT_START (0x11000000) -#define CONFIG_SYS_MMC_U_BOOT_OFFS (96 << 10) +#define CONFIG_SYS_MMC_U_BOOT_OFFS (128 << 10) #define CONFIG_SYS_MPC85XX_NO_RESETVEC #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" #define CONFIG_SPL_MMC_BOOT @@ -189,12 +189,12 @@ #define CONFIG_FSL_LAW /* Use common FSL init code */ #define CONFIG_SYS_TEXT_BASE 0x11001000 #define CONFIG_SPL_TEXT_BASE 0xf8f81000 -#define CONFIG_SPL_PAD_TO 0x18000 -#define CONFIG_SPL_MAX_SIZE (96 * 1024) +#define CONFIG_SPL_PAD_TO 0x20000 +#define CONFIG_SPL_MAX_SIZE (128 * 1024) #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x11000000) #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x11000000) -#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (96 << 10) +#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (128 << 10) #define CONFIG_SYS_MPC85XX_NO_RESETVEC #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" #define CONFIG_SPL_SPI_BOOT @@ -579,11 +579,15 @@ #define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) #define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000 -#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 128 * 1024) -#define CONFIG_SPL_RELOC_STACK_SIZE (32 << 10) -#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 160 * 1024) -#define CONFIG_SPL_RELOC_MALLOC_SIZE (96 << 10) #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 112 * 1024) +#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 116 * 1024) +#define CONFIG_SPL_RELOC_STACK_SIZE (32 << 10) +#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 148 * 1024) +#if defined(CONFIG_P2020RDB) +#define CONFIG_SPL_RELOC_MALLOC_SIZE (364 << 10) +#else +#define CONFIG_SPL_RELOC_MALLOC_SIZE (108 << 10) +#endif #elif defined(CONFIG_NAND) #ifdef CONFIG_TPL_BUILD #define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h index 601bac72e0..c296a07599 100644 --- a/include/configs/p1_twr.h +++ b/include/configs/p1_twr.h @@ -238,9 +238,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_OF_BOARD_SETUP #define CONFIG_OF_STDOUT_VIA_ALIAS -#define CONFIG_SYS_64BIT_VSPRINTF -#define CONFIG_SYS_64BIT_STRTOUL - /* new uImage format support */ #define CONFIG_FIT #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ diff --git a/include/configs/palmld.h b/include/configs/palmld.h index 2a9fd22dd6..9480d8daf2 100644 --- a/include/configs/palmld.h +++ b/include/configs/palmld.h @@ -115,7 +115,6 @@ * Clock Configuration */ #undef CONFIG_SYS_CLKS_IN_HZ -#define CONFIG_SYS_HZ 1000 #define CONFIG_SYS_CPUSPEED 0x210 /* 416MHz ; N=2,L=16 */ /* diff --git a/include/configs/palmtc.h b/include/configs/palmtc.h index de254076f2..8abce1b425 100644 --- a/include/configs/palmtc.h +++ b/include/configs/palmtc.h @@ -117,7 +117,6 @@ * Clock Configuration */ #undef CONFIG_SYS_CLKS_IN_HZ -#define CONFIG_SYS_HZ 1000 #define CONFIG_SYS_CPUSPEED 0x161 /* 400MHz;L=1 M=3 T=1 */ /* diff --git a/include/configs/pcm051.h b/include/configs/pcm051.h index 6f41ee7718..9af3efd4b1 100644 --- a/include/configs/pcm051.h +++ b/include/configs/pcm051.h @@ -297,7 +297,6 @@ #define CONFIG_NET_MULTI #define CONFIG_PHY_GIGE #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_SMSC #endif /* ! __CONFIG_PCM051_H */ diff --git a/include/configs/pengwyn.h b/include/configs/pengwyn.h new file mode 100644 index 0000000000..fc25966e0f --- /dev/null +++ b/include/configs/pengwyn.h @@ -0,0 +1,207 @@ +/* + * pengwyn.h + * + * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com> + * + * based on am335x_evm.h, Copyright (C) 2011 Texas Instruments Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_PENGWYN_H +#define __CONFIG_PENGWYN_H + +#define CONFIG_NAND +#define CONFIG_SERIAL1 +#define CONFIG_CONS_INDEX 1 + +#include <configs/ti_am335x_common.h> + +/* Clock Defines */ +#define V_OSCK 24000000 +#define V_SCLK V_OSCK + +/* set env size */ +#define CONFIG_ENV_SIZE 0x4000 + +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + +#ifndef CONFIG_SPL_BUILD +#define CONFIG_EXTRA_ENV_SETTINGS \ + "loadaddr=0x80200000\0" \ + "fdtaddr=0x80F80000\0" \ + "bootpart=0:2\0" \ + "bootdir=/boot\0" \ + "bootfile=zImage\0" \ + "fdtfile=am335x-pengwyn.dtb\0" \ + "console=ttyO0,115200n8\0" \ + "optargs=\0" \ + "mmcdev=0\0" \ + "mmcroot=/dev/mmcblk0p2 ro\0" \ + "mmcrootfstype=ext4 rootwait\0" \ + "rootpath=/export/rootfs\0" \ + "nfsopts=nolock\0" \ + "static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \ + "::off\0" \ + "mmcargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=${mmcroot} " \ + "rootfstype=${mmcrootfstype}\0" \ + "netargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=/dev/nfs " \ + "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \ + "ip=dhcp\0" \ + "bootenv=uEnv.txt\0" \ + "loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \ + "importbootenv=echo Importing environment from mmc ...; " \ + "env import -t $loadaddr $filesize\0" \ + "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \ + "loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \ + "mmcloados=run mmcargs; " \ + "bootz ${loadaddr} - ${fdtaddr};\0" \ + "mmcboot=mmc dev ${mmcdev}; " \ + "if mmc rescan; then " \ + "echo SD/MMC found on device ${mmcdev};" \ + "if run loadbootenv; then " \ + "echo Loaded environment from ${bootenv};" \ + "run importbootenv;" \ + "fi;" \ + "if test -n $uenvcmd; then " \ + "echo Running uenvcmd ...;" \ + "run uenvcmd;" \ + "fi;" \ + "if run loadimage; then " \ + "run loadfdt;" \ + "run mmcloados;" \ + "fi;" \ + "fi;\0" \ + "netboot=echo Booting from network ...; " \ + "setenv autoload no; " \ + "dhcp; " \ + "tftp ${loadaddr} ${bootfile}; " \ + "tftp ${fdtaddr} ${fdtfile}; " \ + "run netargs; " \ + "bootz ${loadaddr} - ${fdtaddr}\0" \ + "mtdids=" MTDIDS_DEFAULT "\0" \ + "mtdparts=" MTDPARTS_DEFAULT "\0" \ + "nandargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=${nandroot} " \ + "rootfstype=${nandrootfstype}\0" \ + "nandroot=ubi0:rootfs rw ubi.mtd=7,2048\0" \ + "nandrootfstype=ubifs rootwait=1\0" \ + "nandboot=echo Booting from nand ...; " \ + "run nandargs; " \ + "nand read ${fdtaddr} u-boot-spl-os; " \ + "nand read ${loadaddr} kernel; " \ + "bootz ${loadaddr} - ${fdtaddr}\0" +#endif + +#define CONFIG_BOOTCOMMAND \ + "run mmcboot;" \ + "run nandboot;" + +/* NS16550 Configuration: primary UART via FDTI */ +#define CONFIG_SYS_NS16550_COM1 0x44e09000 +#define CONFIG_BAUDRATE 115200 + +/* I2C Configuration */ +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_CMD_EEPROM +#define CONFIG_ENV_EEPROM_IS_ON_I2C +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_I2C_MULTI_EEPROMS + +/* SPL */ +#define CONFIG_SPL_POWER_SUPPORT +#define CONFIG_SPL_YMODEM_SUPPORT + +/* General network SPL */ +#define CONFIG_SPL_NET_SUPPORT +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_NET_VCI_STRING "AM335x U-Boot SPL" + +/* NAND support */ +#define CONFIG_CMD_NAND +#define CONFIG_NAND_OMAP_GPMC +#define CONFIG_NAND_OMAP_ELM +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ + CONFIG_SYS_NAND_PAGE_SIZE) +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) +#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS +#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \ + 10, 11, 12, 13, 14, 15, 16, 17, \ + 18, 19, 20, 21, 22, 23, 24, 25, \ + 26, 27, 28, 29, 30, 31, 32, 33, \ + 34, 35, 36, 37, 38, 39, 40, 41, \ + 42, 43, 44, 45, 46, 47, 48, 49, \ + 50, 51, 52, 53, 54, 55, 56, 57, } + +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 14 +#define CONFIG_SYS_NAND_ONFI_DETECTION +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 + +#define GPMC_NAND_ECC_LP_x8_LAYOUT 1 +#define MTDIDS_DEFAULT "nand0=omap2-nand.0" +#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:128k(SPL)," \ + "128k(SPL.backup1)," \ + "128k(SPL.backup2)," \ + "128k(SPL.backup3),1792k(u-boot)," \ + "128k(u-boot-spl-os)," \ + "128k(u-boot-env),5m(kernel),-(rootfs)" +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */ +#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ + +/* + * USB configuration. We enable MUSB support, both for host and for + * gadget. We set USB0 as peripheral and USB1 as host, based on the + * board schematic and physical port wired to each. Then for host we + * add mass storage support. + */ +#define CONFIG_USB_MUSB_DSPS +#define CONFIG_ARCH_MISC_INIT +#define CONFIG_MUSB_GADGET +#define CONFIG_MUSB_PIO_ONLY +#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT +#define CONFIG_USB_GADGET +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_USB_GADGET_VBUS_DRAW 2 +#define CONFIG_MUSB_HOST +#define CONFIG_AM335X_USB0 +#define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL +#define CONFIG_AM335X_USB1 +#define CONFIG_AM335X_USB1_MODE MUSB_HOST + +#if defined(CONFIG_MUSB_HOST) +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#endif + +#if defined(CONFIG_SPL_BUILD) +/* disable host part of MUSB in SPL */ +#undef CONFIG_MUSB_HOST +/* Disable CPSW SPL support so we fit within the 101KiB limit. */ +#undef CONFIG_SPL_ETH_SUPPORT +#endif + +/* Network */ +#define CONFIG_CMD_MII +#define CONFIG_PHYLIB +#define CONFIG_PHY_RESET 1 +#define CONFIG_PHY_NATSEMI + +/* CPSW support */ +#define CONFIG_SPL_ETH_SUPPORT + +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds" + +#endif /* ! __CONFIG_PENGWYN_H */ diff --git a/include/configs/pxm2.h b/include/configs/pxm2.h index 7722f7be2e..6276d43395 100644 --- a/include/configs/pxm2.h +++ b/include/configs/pxm2.h @@ -44,7 +44,6 @@ #undef CONFIG_SPL_NET_VCI_STRING #undef CONFIG_SPL_ETH_SUPPORT -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_ATHEROS #define CONFIG_FACTORYSET diff --git a/include/configs/r0p7734.h b/include/configs/r0p7734.h index 53128ecc12..a71709bc7c 100644 --- a/include/configs/r0p7734.h +++ b/include/configs/r0p7734.h @@ -140,8 +140,6 @@ #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Size of DRAM reserved for malloc() use */ #define CONFIG_SYS_MALLOC_LEN (256 * 1024) -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE (256) #define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) /* ENV setting */ diff --git a/include/configs/rpi_b.h b/include/configs/rpi_b.h index 0b7add7bea..6306d61bb2 100644 --- a/include/configs/rpi_b.h +++ b/include/configs/rpi_b.h @@ -95,12 +95,25 @@ #define CONFIG_SYS_LOAD_ADDR 0x1000000 #define CONFIG_CONSOLE_MUX #define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_PREBOOT \ + "if load mmc 0:1 ${loadaddr} /uEnv.txt; then " \ + "env import -t ${loadaddr} ${filesize}; " \ + "fi" + +#define ENV_DEVICE_SETTINGS \ + "stdin=serial,lcd\0" \ + "stdout=serial,lcd\0" \ + "stderr=serial,lcd\0" + /* * Memory layout for where various images get loaded by boot scripts: * * scriptaddr can be pretty much anywhere that doesn't conflict with something * else. Put it low in memory to avoid conflicts. * + * pxefile_addr_r can be pretty much anywhere that doesn't conflict with + * something else. Put it low in memory to avoid conflicts. + * * kernel_addr_r must be within the first 128M of RAM in order for the * kernel's CONFIG_AUTO_ZRELADDR option to work. Since the kernel will * decompress itself to 0x8000 after the start of RAM, kernel_addr_r @@ -116,67 +129,112 @@ * ramdisk_addr_r simply shouldn't overlap anything else. Choosing 33M allows * for the FDT/DTB to be up to 1M, which is hopefully plenty. */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - "stdin=serial\0" \ - "stderr=serial,lcd\0" \ - "stdout=serial,lcd\0" \ +#define ENV_MEM_LAYOUT_SETTINGS \ "scriptaddr=0x00000000\0" \ + "pxefile_addr_r=0x00100000\0" \ "kernel_addr_r=0x01000000\0" \ "fdt_addr_r=0x02000000\0" \ + "fdtfile=bcm2835-rpi-b.dtb\0" \ "ramdisk_addr_r=0x02100000\0" \ - "boot_targets=mmc0\0" \ - \ - "script_boot=" \ - "if fatload ${devtype} ${devnum}:1 " \ - "${scriptaddr} boot.scr.uimg; then " \ - "source ${scriptaddr}; " \ - "fi;\0" \ - \ + +#define BOOTCMDS_MMC \ "mmc_boot=" \ "setenv devtype mmc; " \ "if mmc dev ${devnum}; then " \ - "run script_boot; " \ + "run scan_boot; " \ "fi\0" \ + "bootcmd_mmc0=setenv devnum 0; run mmc_boot;\0" +#define BOOT_TARGETS_MMC "mmc0" + +#define BOOTCMDS_COMMON \ + "rootpart=1\0" \ + \ + "do_script_boot=" \ + "load ${devtype} ${devnum}:${rootpart} " \ + "${scriptaddr} ${prefix}${script}; " \ + "source ${scriptaddr}\0" \ + \ + "script_boot=" \ + "for script in ${boot_scripts}; do " \ + "if test -e ${devtype} ${devnum}:${rootpart} " \ + "${prefix}${script}; then " \ + "echo Found ${prefix}${script}; " \ + "run do_script_boot; " \ + "echo SCRIPT FAILED: continuing...; " \ + "fi; " \ + "done\0" \ + \ + "do_sysboot_boot=" \ + "sysboot ${devtype} ${devnum}:${rootpart} any " \ + "${scriptaddr} ${prefix}extlinux/extlinux.conf\0" \ + \ + "sysboot_boot=" \ + "if test -e ${devtype} ${devnum}:${rootpart} " \ + "${prefix}extlinux/extlinux.conf; then " \ + "echo Found ${prefix}extlinux/extlinux.conf; " \ + "run do_sysboot_boot; " \ + "echo SCRIPT FAILED: continuing...; " \ + "fi\0" \ + \ + "scan_boot=" \ + "echo Scanning ${devtype} ${devnum}...; " \ + "for prefix in ${boot_prefixes}; do " \ + "run sysboot_boot; " \ + "run script_boot; " \ + "done\0" \ + \ + "boot_targets=" \ + BOOT_TARGETS_MMC " " \ + "\0" \ + \ + "boot_prefixes=/\0" \ + \ + "boot_scripts=boot.scr.uimg\0" \ \ - "bootcmd_mmc0=setenv devnum 0; run mmc_boot\0" \ + BOOTCMDS_MMC #define CONFIG_BOOTCOMMAND \ "for target in ${boot_targets}; do run bootcmd_${target}; done" -#define CONFIG_BOOTDELAY 2 +#define CONFIG_BOOTCOMMAND \ + "for target in ${boot_targets}; do run bootcmd_${target}; done" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + ENV_DEVICE_SETTINGS \ + ENV_MEM_LAYOUT_SETTINGS \ + BOOTCMDS_COMMON + +#define CONFIG_BOOTDELAY 2 /* Shell */ -#define CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_MAXARGS 8 #define CONFIG_SYS_PROMPT "U-Boot> " -#define CONFIG_SYS_LONGHELP -#define CONFIG_CMDLINE_EDITING #define CONFIG_COMMAND_HISTORY -#define CONFIG_AUTO_COMPLETE /* Commands */ #include <config_cmd_default.h> -#define CONFIG_CMD_BOOTZ #define CONFIG_CMD_GPIO #define CONFIG_CMD_MMC -#define CONFIG_DOS_PARTITION #define CONFIG_PARTITION_UUIDS #define CONFIG_CMD_PART -#define CONFIG_CMD_FS_GENERIC -#define CONFIG_CMD_FAT -#define CONFIG_CMD_EXT -/* Some things don't make sense on this HW or yet */ -#undef CONFIG_CMD_FPGA -#undef CONFIG_CMD_NET -#undef CONFIG_CMD_NFS -#undef CONFIG_CMD_SAVEENV -/* Device tree support for bootm/bootz */ -#define CONFIG_OF_LIBFDT +/* Device tree support */ #define CONFIG_OF_BOARD_SETUP /* ATAGs support for bootm/bootz */ #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_CMDLINE_TAG #define CONFIG_INITRD_TAG +#include <config_distro_defaults.h> + +/* Some things don't make sense on this HW or yet */ +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_NFS +#undef CONFIG_CMD_SAVEENV +#undef CONFIG_CMD_DHCP +#undef CONFIG_CMD_MII +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_PING + #endif diff --git a/include/configs/rut.h b/include/configs/rut.h index d4519f946c..6bddededae 100644 --- a/include/configs/rut.h +++ b/include/configs/rut.h @@ -41,7 +41,6 @@ #undef CONFIG_SPL_NET_VCI_STRING #undef CONFIG_SPL_ETH_SUPPORT -#define CONFIG_PHY_ADDR 1 #define CONFIG_PHY_NATSEMI #define CONFIG_FACTORYSET diff --git a/include/configs/s5p_goni.h b/include/configs/s5p_goni.h index 0590d201ce..991c43e1cc 100644 --- a/include/configs/s5p_goni.h +++ b/include/configs/s5p_goni.h @@ -34,6 +34,7 @@ #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_CMDLINE_TAG +#define CONFIG_REVISION_TAG #define CONFIG_INITRD_TAG #define CONFIG_CMDLINE_EDITING @@ -113,8 +114,13 @@ #define CONFIG_UBIFS_OPTION "rootflags=bulk_read,no_chk_data_crc" +#define CONFIG_MISC_COMMON +#define CONFIG_MISC_INIT_R + #define CONFIG_ENV_OVERWRITE #define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_ENV_VARS_UBOOT_CONFIG +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG #define CONFIG_EXTRA_ENV_SETTINGS \ CONFIG_UPDATEB \ "updatek=" \ @@ -208,8 +214,8 @@ /* * I2C Settings */ -#define CONFIG_SOFT_I2C_GPIO_SCL s5pc110_gpio_get_nr(j4, 3) -#define CONFIG_SOFT_I2C_GPIO_SDA s5pc110_gpio_get_nr(j4, 0) +#define CONFIG_SOFT_I2C_GPIO_SCL s5pc110_gpio_get(j4, 3) +#define CONFIG_SOFT_I2C_GPIO_SDA s5pc110_gpio_get(j4, 0) #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ diff --git a/include/configs/s5pc210_universal.h b/include/configs/s5pc210_universal.h index d9e4c5683f..67921e900b 100644 --- a/include/configs/s5pc210_universal.h +++ b/include/configs/s5pc210_universal.h @@ -124,6 +124,9 @@ #define CONFIG_SYS_CONSOLE_INFO_QUIET #define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_ENV_VARS_UBOOT_CONFIG +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + #define CONFIG_EXTRA_ENV_SETTINGS \ "updateb=" \ "onenand erase 0x0 0x100000;" \ @@ -229,8 +232,8 @@ /* * I2C Settings */ -#define CONFIG_SOFT_I2C_GPIO_SCL exynos4_gpio_part1_get_nr(b, 7) -#define CONFIG_SOFT_I2C_GPIO_SDA exynos4_gpio_part1_get_nr(b, 6) +#define CONFIG_SOFT_I2C_GPIO_SCL exynos4_gpio_get(1, b, 7) +#define CONFIG_SOFT_I2C_GPIO_SDA exynos4_gpio_get(1, b, 6) #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ @@ -253,10 +256,10 @@ */ #define CONFIG_SOFT_SPI #define CONFIG_SOFT_SPI_MODE SPI_MODE_3 -#define CONFIG_SOFT_SPI_GPIO_SCLK exynos4_gpio_part2_get_nr(y3, 1) -#define CONFIG_SOFT_SPI_GPIO_MOSI exynos4_gpio_part2_get_nr(y3, 3) -#define CONFIG_SOFT_SPI_GPIO_MISO exynos4_gpio_part2_get_nr(y3, 0) -#define CONFIG_SOFT_SPI_GPIO_CS exynos4_gpio_part2_get_nr(y4, 3) +#define CONFIG_SOFT_SPI_GPIO_SCLK exynos4_gpio_get(2, y3, 1) +#define CONFIG_SOFT_SPI_GPIO_MOSI exynos4_gpio_get(2, y3, 3) +#define CONFIG_SOFT_SPI_GPIO_MISO exynos4_gpio_get(2, y3, 0) +#define CONFIG_SOFT_SPI_GPIO_CS exynos4_gpio_get(2, y4, 3) #define SPI_DELAY udelay(1) #undef SPI_INIT @@ -269,16 +272,43 @@ void universal_spi_sda(int bit); int universal_spi_read(void); #endif +/* Common misc for Samsung */ +#define CONFIG_MISC_COMMON + +#define CONFIG_MISC_INIT_R + +/* Download menu - Samsung common */ +#define CONFIG_LCD_MENU +#define CONFIG_LCD_MENU_BOARD + +/* Download menu - definitions for check keys */ +#ifndef __ASSEMBLY__ +#include <power/max8998_pmic.h> + +#define KEY_PWR_PMIC_NAME "MAX8998_PMIC" +#define KEY_PWR_STATUS_REG MAX8998_REG_STATUS1 +#define KEY_PWR_STATUS_MASK (1 << 7) +#define KEY_PWR_INTERRUPT_REG MAX8998_REG_IRQ1 +#define KEY_PWR_INTERRUPT_MASK (1 << 7) + +#define KEY_VOL_UP_GPIO exynos4_gpio_get(2, x2, 0) +#define KEY_VOL_DOWN_GPIO exynos4_gpio_get(2, x2, 1) +#endif /* __ASSEMBLY__ */ + +/* LCD console */ +#define LCD_BPP LCD_COLOR16 +#define CONFIG_SYS_WHITE_ON_BLACK + /* * LCD Settings */ #define CONFIG_EXYNOS_FB #define CONFIG_LCD #define CONFIG_CMD_BMP -#define CONFIG_BMP_32BPP +#define CONFIG_BMP_16BPP #define CONFIG_LD9040 #define CONFIG_EXYNOS_MIPI_DSIM #define CONFIG_VIDEO_BMP_GZIP -#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE ((520 * 120 * 4) + (1 << 12)) +#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE ((500 * 160 * 4) + 54) #endif /* __CONFIG_H */ diff --git a/include/configs/sandbox.h b/include/configs/sandbox.h index a6d55822b8..e77d06bcd3 100644 --- a/include/configs/sandbox.h +++ b/include/configs/sandbox.h @@ -42,6 +42,7 @@ #define CONFIG_CMD_PART #define CONFIG_DOS_PARTITION #define CONFIG_HOST_MAX_DEVICES 4 +#define CONFIG_CMD_FS_GENERIC #define CONFIG_SYS_VSNPRINTF diff --git a/include/configs/sansa_fuze_plus.h b/include/configs/sansa_fuze_plus.h index a85eb1c3fc..8cce34af76 100644 --- a/include/configs/sansa_fuze_plus.h +++ b/include/configs/sansa_fuze_plus.h @@ -56,7 +56,7 @@ #define CONFIG_EHCI_MXS_PORT0 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 -#define CONFIG_MV_UDC /* ChipIdea CI13xxx UDC */ +#define CONFIG_CI_UDC /* ChipIdea CI13xxx UDC */ #define CONFIG_USB_GADGET_DUALSPEED #define CONFIG_USB_ETHER diff --git a/include/configs/scb9328.h b/include/configs/scb9328.h index c0048aca78..e6d272dd1f 100644 --- a/include/configs/scb9328.h +++ b/include/configs/scb9328.h @@ -69,7 +69,6 @@ #define CONFIG_SYS_MEMTEST_START 0x08100000 /* memtest test area */ #define CONFIG_SYS_MEMTEST_END 0x08F00000 -#define CONFIG_SYS_HZ 1000 #define CONFIG_SYS_CPUSPEED 0x141 /* core clock - register value */ #define CONFIG_BAUDRATE 115200 diff --git a/include/configs/shmin.h b/include/configs/shmin.h index f8155efbc9..4d38f6c554 100644 --- a/include/configs/shmin.h +++ b/include/configs/shmin.h @@ -62,7 +62,6 @@ #define CONFIG_SYS_MONITOR_BASE (SHMIN_FLASH_BASE_1 + CONFIG_ENV_SECT_SIZE) #define CONFIG_SYS_MONITOR_LEN (128 * 1024) #define CONFIG_SYS_MALLOC_LEN (256 * 1024) -#define CONFIG_SYS_GBL_DATA_SIZE 256 #define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) /* FLASH */ diff --git a/include/configs/smdk5420.h b/include/configs/smdk5420.h index 447f8e5810..b96eea8890 100644 --- a/include/configs/smdk5420.h +++ b/include/configs/smdk5420.h @@ -17,8 +17,6 @@ #undef CONFIG_DEFAULT_DEVICE_TREE #define CONFIG_DEFAULT_DEVICE_TREE exynos5420-smdk5420 -#define CONFIG_ARCH_DEVICE_TREE exynos5420 - #define CONFIG_VAR_SIZE_SPL #define CONFIG_SYS_SDRAM_BASE 0x20000000 diff --git a/include/configs/snowball.h b/include/configs/snowball.h index 9a069f3cdb..dacb5604cd 100644 --- a/include/configs/snowball.h +++ b/include/configs/snowball.h @@ -41,8 +41,6 @@ #define CONFIG_ENV_SIZE (8*1024) #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256*1024) -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* for initial data */ - #define CONFIG_ENV_IS_IN_MMC #define CONFIG_CMD_ENV #define CONFIG_CMD_SAVEENV diff --git a/include/configs/spear-common.h b/include/configs/spear-common.h index 23f7ad77b6..c0eba3721d 100644 --- a/include/configs/spear-common.h +++ b/include/configs/spear-common.h @@ -17,11 +17,9 @@ /* Ethernet driver configuration */ #define CONFIG_MII #define CONFIG_DESIGNWARE_ETH -#define CONFIG_DW_SEARCH_PHY -#define CONFIG_DW0_PHY 1 #define CONFIG_NET_MULTI +#define CONFIG_PHYLIB #define CONFIG_PHY_RESET_DELAY 10000 /* in usec */ -#define CONFIG_DW_AUTONEG #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ /* USBD driver configuration */ @@ -41,6 +39,15 @@ /* I2C driver configuration */ #define CONFIG_HARD_I2C #define CONFIG_DW_I2C +#if defined(CONFIG_SPEAR600) +#define CONFIG_SYS_I2C_BASE 0xD0200000 +#elif defined(CONFIG_SPEAR300) +#define CONFIG_SYS_I2C_BASE 0xD0180000 +#elif defined(CONFIG_SPEAR310) +#define CONFIG_SYS_I2C_BASE 0xD0180000 +#elif defined(CONFIG_SPEAR320) +#define CONFIG_SYS_I2C_BASE 0xD0180000 +#endif #define CONFIG_SYS_I2C_SPEED 400000 #define CONFIG_SYS_I2C_SLAVE 0x02 diff --git a/include/configs/spear6xx_evb.h b/include/configs/spear6xx_evb.h index 7f4dc5801c..28dddcc5b9 100644 --- a/include/configs/spear6xx_evb.h +++ b/include/configs/spear6xx_evb.h @@ -37,6 +37,9 @@ #define CONFIG_SYS_FSMC_NAND_8BIT #define CONFIG_SYS_NAND_BASE 0xD2000000 +/* Ethernet PHY configuration */ +#define CONFIG_PHY_NATSEMI + /* Environment Settings */ #define CONFIG_EXTRA_ENV_SETTINGS CONFIG_EXTRA_ENV_USBTTY diff --git a/include/configs/tao3530.h b/include/configs/tao3530.h index 9abfe82902..9c04c23ab7 100644 --- a/include/configs/tao3530.h +++ b/include/configs/tao3530.h @@ -83,6 +83,13 @@ #define CONFIG_OMAP_HSMMC #define CONFIG_DOS_PARTITION +/* GPIO banks */ +#define CONFIG_OMAP3_GPIO_2 /* GPIO32 ..63 is in GPIO bank 2 */ +#define CONFIG_OMAP3_GPIO_3 /* GPIO64 ..95 is in GPIO bank 3 */ +#define CONFIG_OMAP3_GPIO_4 /* GPIO96 ..127 is in GPIO bank 4 */ +#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */ +#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */ + /* commands to include */ #include <config_cmd_default.h> diff --git a/include/configs/taurus.h b/include/configs/taurus.h index c98002317f..20d4cee011 100644 --- a/include/configs/taurus.h +++ b/include/configs/taurus.h @@ -37,7 +37,6 @@ /* ARM asynchronous clock */ #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ #define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* main clock xtal */ -#define CONFIG_SYS_HZ 1000 /* Misc CPU related */ #define CONFIG_ARCH_CPU_INIT diff --git a/include/configs/tegra-common-post.h b/include/configs/tegra-common-post.h index a3242fe612..e1a3bbc626 100644 --- a/include/configs/tegra-common-post.h +++ b/include/configs/tegra-common-post.h @@ -99,6 +99,7 @@ BOOTCMDS_DHCP #define CONFIG_BOOTCOMMAND \ + "set usb_need_init; " \ "for target in ${boot_targets}; do run bootcmd_${target}; done" #endif @@ -129,10 +130,15 @@ "stderr=serial" STDOUT_LCD "\0" \ "" +#ifndef BOARD_EXTRA_ENV_SETTINGS +#define BOARD_EXTRA_ENV_SETTINGS +#endif + #define CONFIG_EXTRA_ENV_SETTINGS \ TEGRA_DEVICE_SETTINGS \ MEM_LAYOUT_ENV_SETTINGS \ - BOOTCMDS_COMMON + BOOTCMDS_COMMON \ + BOARD_EXTRA_ENV_SETTINGS #if defined(CONFIG_TEGRA20_SFLASH) || defined(CONFIG_TEGRA20_SLINK) || defined(CONFIG_TEGRA114_SPI) #define CONFIG_FDT_SPI diff --git a/include/configs/tegra124-common.h b/include/configs/tegra124-common.h new file mode 100644 index 0000000000..0a4541bd20 --- /dev/null +++ b/include/configs/tegra124-common.h @@ -0,0 +1,83 @@ +/* + * (C) Copyright 2013 + * NVIDIA Corporation <www.nvidia.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _TEGRA124_COMMON_H_ +#define _TEGRA124_COMMON_H_ + +#include "tegra-common.h" + +/* Cortex-A15 uses a cache line size of 64 bytes */ +#define CONFIG_SYS_CACHELINE_SIZE 64 + +/* + * NS16550 Configuration + */ +#define V_NS16550_CLK 408000000 /* 408MHz (pllp_out0) */ + +/* + * High Level Configuration Options + */ +#define CONFIG_TEGRA124 /* is an NVIDIA Tegra124 core */ + +/* Environment information, boards can override if required */ +#define CONFIG_LOADADDR 0x80408000 /* def. location for kernel */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LOAD_ADDR 0x80A00800 /* default */ +#define CONFIG_STACKBASE 0x82800000 /* 40MB */ + +/*----------------------------------------------------------------------- + * Physical Memory Map + */ +#define CONFIG_SYS_TEXT_BASE 0x8010E000 + +/* + * Memory layout for where various images get loaded by boot scripts: + * + * scriptaddr can be pretty much anywhere that doesn't conflict with something + * else. Put it above BOOTMAPSZ to eliminate conflicts. + * + * pxefile_addr_r can be pretty much anywhere that doesn't conflict with + * something else. Put it above BOOTMAPSZ to eliminate conflicts. + * + * kernel_addr_r must be within the first 128M of RAM in order for the + * kernel's CONFIG_AUTO_ZRELADDR option to work. Since the kernel will + * decompress itself to 0x8000 after the start of RAM, kernel_addr_r + * should not overlap that area, or the kernel will have to copy itself + * somewhere else before decompression. Similarly, the address of any other + * data passed to the kernel shouldn't overlap the start of RAM. Pushing + * this up to 16M allows for a sizable kernel to be decompressed below the + * compressed load address. + * + * fdt_addr_r simply shouldn't overlap anything else. Choosing 32M allows for + * the compressed kernel to be up to 16M too. + * + * ramdisk_addr_r simply shouldn't overlap anything else. Choosing 33M allows + * for the FDT/DTB to be up to 1M, which is hopefully plenty. + */ +#define MEM_LAYOUT_ENV_SETTINGS \ + "scriptaddr=0x90000000\0" \ + "pxefile_addr_r=0x90100000\0" \ + "kernel_addr_r=0x81000000\0" \ + "fdt_addr_r=0x82000000\0" \ + "ramdisk_addr_r=0x82100000\0" + +/* Defines for SPL */ +#define CONFIG_SPL_TEXT_BASE 0x80108000 +#define CONFIG_SYS_SPL_MALLOC_START 0x80090000 +#define CONFIG_SPL_STACK 0x800ffffc + +/* Total I2C ports on Tegra124 */ +#define TEGRA_I2C_NUM_CONTROLLERS 5 + +/* For USB EHCI controller */ +#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_EHCI_TXFIFO_THRESH 0x10 + +#endif /* _TEGRA124_COMMON_H_ */ diff --git a/include/configs/ti814x_evm.h b/include/configs/ti814x_evm.h index ba16b1c14b..b51400c464 100644 --- a/include/configs/ti814x_evm.h +++ b/include/configs/ti814x_evm.h @@ -233,7 +233,6 @@ #define CONFIG_NET_MULTI #define CONFIG_PHY_GIGE #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 1 #define CONFIG_PHY_ET1011C #define CONFIG_PHY_ET1011C_TX_CLK_FIX diff --git a/include/configs/ti_am335x_common.h b/include/configs/ti_am335x_common.h index 91f97dd061..50c32037ff 100644 --- a/include/configs/ti_am335x_common.h +++ b/include/configs/ti_am335x_common.h @@ -13,7 +13,6 @@ #define __CONFIG_TI_AM335X_COMMON_H__ #define CONFIG_AM33XX -#define CONFIG_BOARD_LATE_INIT #define CONFIG_ARCH_CPU_INIT #define CONFIG_SYS_CACHELINE_SIZE 64 #define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ @@ -31,6 +30,7 @@ /* Network defines. */ #define CONFIG_CMD_NET /* 'bootp' and 'tftp' */ #define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII #define CONFIG_BOOTP_DNS /* Configurable parts of CMD_DHCP */ #define CONFIG_BOOTP_DNS2 #define CONFIG_BOOTP_SEND_HOSTNAME diff --git a/include/configs/ti_omap4_common.h b/include/configs/ti_omap4_common.h index 2f0e4c0f67..bcb5eabd75 100644 --- a/include/configs/ti_omap4_common.h +++ b/include/configs/ti_omap4_common.h @@ -163,4 +163,10 @@ #define CONFIG_SPL_NAND_AM33XX_BCH /* ELM support */ #endif +#ifdef CONFIG_SPL_BUILD +/* No need for i2c in SPL mode as we will use SRI2C for PMIC access on OMAP4 */ +#undef CONFIG_SYS_I2C +#undef CONFIG_SYS_I2C_OMAP24XX +#endif + #endif /* __CONFIG_TI_OMAP4_COMMON_H */ diff --git a/include/configs/trats.h b/include/configs/trats.h index fdd8b460b0..718107ac9f 100644 --- a/include/configs/trats.h +++ b/include/configs/trats.h @@ -147,15 +147,23 @@ ""PARTS_BOOT" part 0 2;" \ ""PARTS_ROOT" part 0 5;" \ ""PARTS_DATA" part 0 6;" \ - ""PARTS_UMS" part 0 7\0" + ""PARTS_UMS" part 0 7;" \ + "params.bin mmc 0x38 0x8\0" #define CONFIG_ENV_OVERWRITE #define CONFIG_SYS_CONSOLE_INFO_QUIET #define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_ENV_VARS_UBOOT_CONFIG +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + #define CONFIG_EXTRA_ENV_SETTINGS \ "bootk=" \ - "run loaddtb; run loaduimage; bootm 0x40007FC0 - ${fdtaddr}\0" \ + "run loaduimage;" \ + "if run loaddtb; then " \ + "bootm 0x40007FC0 - ${fdtaddr};" \ + "fi;" \ + "bootm 0x40007FC0;\0" \ "updatemmc=" \ "mmc boot 0 1 1 1; mmc write 0 0x42008000 0 0x200;" \ "mmc boot 0 1 1 0\0" \ @@ -178,7 +186,7 @@ "mmcboot=" \ "setenv bootargs root=/dev/mmcblk${mmcdev}p${mmcrootpart} " \ "${lpj} rootwait ${console} ${meminfo} ${opts} ${lcdinfo}; " \ - "run loaddtb; run loaduimage; bootm 0x40007FC0 - ${fdtaddr}\0" \ + "run bootk\0" \ "bootchart=setenv opts init=/sbin/bootchartd; run bootcmd\0" \ "boottrace=setenv opts initcall_debug; run bootcmd\0" \ "mmcoops=mmc read 0 0x40000000 0x40 8; md 0x40000000 0x400\0" \ @@ -217,7 +225,6 @@ "setenv spl_imgaddr;" \ "setenv spl_addr_tmp;\0" \ "fdtaddr=40800000\0" \ - "fdtfile=exynos4210-trats.dtb\0" /* Miscellaneous configurable options */ @@ -287,8 +294,8 @@ #include <asm/arch/gpio.h> /* I2C FG */ -#define CONFIG_SOFT_I2C_GPIO_SCL exynos4_gpio_part2_get_nr(y4, 1) -#define CONFIG_SOFT_I2C_GPIO_SDA exynos4_gpio_part2_get_nr(y4, 0) +#define CONFIG_SOFT_I2C_GPIO_SCL exynos4_gpio_get(2, y4, 1) +#define CONFIG_SOFT_I2C_GPIO_SDA exynos4_gpio_get(2, y4, 0) #define CONFIG_POWER #define CONFIG_POWER_I2C @@ -306,16 +313,43 @@ #define CONFIG_USB_GADGET_VBUS_DRAW 2 #define CONFIG_USB_CABLE_CHECK +/* Common misc for Samsung */ +#define CONFIG_MISC_COMMON + +#define CONFIG_MISC_INIT_R + +/* Download menu - Samsung common */ +#define CONFIG_LCD_MENU +#define CONFIG_LCD_MENU_BOARD + +/* Download menu - definitions for check keys */ +#ifndef __ASSEMBLY__ +#include <power/max8997_pmic.h> + +#define KEY_PWR_PMIC_NAME "MAX8997_PMIC" +#define KEY_PWR_STATUS_REG MAX8997_REG_STATUS1 +#define KEY_PWR_STATUS_MASK (1 << 0) +#define KEY_PWR_INTERRUPT_REG MAX8997_REG_INT1 +#define KEY_PWR_INTERRUPT_MASK (1 << 0) + +#define KEY_VOL_UP_GPIO exynos4_gpio_get(2, x2, 0) +#define KEY_VOL_DOWN_GPIO exynos4_gpio_get(2, x2, 1) +#endif /* __ASSEMBLY__ */ + +/* LCD console */ +#define LCD_BPP LCD_COLOR16 +#define CONFIG_SYS_WHITE_ON_BLACK + /* LCD */ #define CONFIG_EXYNOS_FB #define CONFIG_LCD #define CONFIG_CMD_BMP -#define CONFIG_BMP_32BPP +#define CONFIG_BMP_16BPP #define CONFIG_FB_ADDR 0x52504000 #define CONFIG_S6E8AX0 #define CONFIG_EXYNOS_MIPI_DSIM #define CONFIG_VIDEO_BMP_GZIP -#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE ((500 * 120 * 4) + (1 << 12)) +#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE ((500 * 160 * 4) + 54) #define CONFIG_CMD_USB_MASS_STORAGE #define CONFIG_USB_GADGET_MASS_STORAGE diff --git a/include/configs/trats2.h b/include/configs/trats2.h index 83633b074d..e30c428a44 100644 --- a/include/configs/trats2.h +++ b/include/configs/trats2.h @@ -152,6 +152,9 @@ #define CONFIG_SYS_CONSOLE_INFO_QUIET #define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_ENV_VARS_UBOOT_CONFIG +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + /* Tizen - partitions definitions */ #define PARTS_CSA "csa" #define PARTS_BOOT "boot" @@ -178,11 +181,16 @@ ""PARTS_BOOT" part 0 2;" \ ""PARTS_ROOT" part 0 5;" \ ""PARTS_DATA" part 0 6;" \ - ""PARTS_UMS" part 0 7\0" + ""PARTS_UMS" part 0 7;" \ + "params.bin mmc 0x38 0x8\0" #define CONFIG_EXTRA_ENV_SETTINGS \ "bootk=" \ - "run loaddtb; run loaduimage; bootm 0x40007FC0 - ${fdtaddr}\0" \ + "run loaduimage;" \ + "if run loaddtb; then " \ + "bootm 0x40007FC0 - ${fdtaddr};" \ + "fi;" \ + "bootm 0x40007FC0;\0" \ "updatemmc=" \ "mmc boot 0 1 1 1; mmc write 0x42008000 0 0x200;" \ "mmc boot 0 1 1 0\0" \ @@ -196,7 +204,7 @@ "mmcboot=" \ "setenv bootargs root=/dev/mmcblk${mmcdev}p${mmcrootpart} " \ "${lpj} rootwait ${console} ${meminfo} ${opts} ${lcdinfo}; " \ - "run loaddtb; run loaduimage; bootm 0x40007FC0 - ${fdtaddr}\0" \ + "run bootk\0" \ "bootchart=set opts init=/sbin/bootchartd; run bootcmd\0" \ "boottrace=setenv opts initcall_debug; run bootcmd\0" \ "verify=n\0" \ @@ -237,7 +245,6 @@ "setenv spl_imgaddr;" \ "setenv spl_addr_tmp;\0" \ "fdtaddr=40800000\0" \ - "fdtfile=exynos4412-trats2.dtb\0" /* * Miscellaneous configurable options @@ -277,7 +284,6 @@ #define CONFIG_EFI_PARTITION #define CONFIG_PARTITION_UUIDS -#define CONFIG_MISC_INIT_R #define CONFIG_BOARD_EARLY_INIT_F /* I2C */ @@ -318,16 +324,43 @@ int get_soft_i2c_sda_pin(void); #define CONFIG_USB_GADGET_VBUS_DRAW 2 #define CONFIG_USB_CABLE_CHECK +/* Common misc for Samsung */ +#define CONFIG_MISC_COMMON + +#define CONFIG_MISC_INIT_R + +/* Download menu - Samsung common */ +#define CONFIG_LCD_MENU +#define CONFIG_LCD_MENU_BOARD + +/* Download menu - definitions for check keys */ +#ifndef __ASSEMBLY__ +#include <power/max77686_pmic.h> + +#define KEY_PWR_PMIC_NAME "MAX77686_PMIC" +#define KEY_PWR_STATUS_REG MAX77686_REG_PMIC_STATUS1 +#define KEY_PWR_STATUS_MASK (1 << 0) +#define KEY_PWR_INTERRUPT_REG MAX77686_REG_PMIC_INT1 +#define KEY_PWR_INTERRUPT_MASK (1 << 1) + +#define KEY_VOL_UP_GPIO exynos4x12_gpio_get(2, x2, 2) +#define KEY_VOL_DOWN_GPIO exynos4x12_gpio_get(2, x3, 3) +#endif /* __ASSEMBLY__ */ + +/* LCD console */ +#define LCD_BPP LCD_COLOR16 +#define CONFIG_SYS_WHITE_ON_BLACK + /* LCD */ #define CONFIG_EXYNOS_FB #define CONFIG_LCD #define CONFIG_CMD_BMP -#define CONFIG_BMP_32BPP +#define CONFIG_BMP_16BPP #define CONFIG_FB_ADDR 0x52504000 #define CONFIG_S6E8AX0 #define CONFIG_EXYNOS_MIPI_DSIM #define CONFIG_VIDEO_BMP_GZIP -#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE ((500 * 250 * 4) + (1 << 12)) +#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE ((500 * 160 * 4) + 54) #define CONFIG_CMD_USB_MASS_STORAGE #define CONFIG_USB_GADGET_MASS_STORAGE diff --git a/include/configs/tseries.h b/include/configs/tseries.h new file mode 100644 index 0000000000..8fb87ac441 --- /dev/null +++ b/include/configs/tseries.h @@ -0,0 +1,265 @@ +/* + * tseries.h + * + * specific parts for B&R T-Series Motherboard + * + * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> - + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_TSERIES_H__ +#define __CONFIG_TSERIES_H__ + +#include <configs/bur_am335x_common.h> +/* ------------------------------------------------------------------------- */ +/* Clock Defines */ +#define V_OSCK 26000000 /* Clock output from T2 */ +#define V_SCLK (V_OSCK) + +#define CONFIG_POWER_TPS65217 + +/* Support both device trees and ATAGs. */ +#define CONFIG_OF_LIBFDT +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_CMD_BOOTZ +/*#define CONFIG_MACH_TYPE 3589*/ +#define CONFIG_MACH_TYPE 0xFFFFFFFF /* TODO: check with kernel*/ + +/* MMC/SD IP block */ +#if defined(CONFIG_EMMC_BOOT) + #define CONFIG_MMC + #define CONFIG_GENERIC_MMC + #define CONFIG_OMAP_HSMMC + #define CONFIG_CMD_MMC + #define CONFIG_SUPPORT_EMMC_BOOT +/* RAW SD card / eMMC locations. */ + #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /*addr. 0x60000 */ + #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ + #define CONFIG_SPL_MMC_SUPPORT +#endif /* CONFIG_EMMC_BOOT */ + +/* + * When we have SPI or NAND flash we expect to be making use of mtdparts, + * both for ease of use in U-Boot and for passing information on to + * the Linux kernel. + */ +#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NAND) +#define CONFIG_MTD_DEVICE /* Required for mtdparts */ +#define CONFIG_CMD_MTDPARTS +#endif /* CONFIG_SPI_BOOT, ... */ + +#undef CONFIG_SPL_OS_BOOT +#ifdef CONFIG_SPL_OS_BOOT +#define CONFIG_SYS_SPL_ARGS_ADDR 0x80F80000 + +/* RAW SD card / eMMC */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */ + +/* NAND */ +#ifdef CONFIG_NAND +#define CONFIG_CMD_SPL_NAND_OFS 0x080000 /* end of u-boot */ +#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x140000 +#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000 +#endif /* CONFIG_NAND */ +#endif /* CONFIG_SPL_OS_BOOT */ + +#ifdef CONFIG_NAND +#define CONFIG_SPL_NAND_AM33XX_BCH /* OMAP4 and later ELM support */ +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 +#endif /* CONFIG_NAND */ + +/* Always 128 KiB env size */ +#define CONFIG_ENV_SIZE (128 << 10) + +#ifdef CONFIG_NAND +#define NANDARGS \ + "mtdids=" MTDIDS_DEFAULT "\0" \ + "mtdparts=" MTDPARTS_DEFAULT "\0" \ + "nandargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=${nandroot} " \ + "rootfstype=${nandrootfstype}\0" \ + "nandroot=ubi0:rootfs rw ubi.mtd=8,2048\0" \ + "nandrootfstype=ubifs rootwait=1\0" \ + "nandimgsize=0x500000\0" \ + "nandboot=echo Booting from nand ...; " \ + "run nandargs; " \ + "nand read ${loadaddr} kernel ${nandimgsize}; " \ + "bootz ${loadaddr}\0" +#else +#define NANDARGS "" +#endif /* CONFIG_NAND */ + +#ifdef CONFIG_MMC +#define MMCARGS \ + "silent=1\0" +#else +#define MMCARGS "" +#endif /* CONFIG_MMC */ + +#ifndef CONFIG_SPL_BUILD +#define CONFIG_EXTRA_ENV_SETTINGS \ + "autoload=0\0" \ + "loadaddr=0x80200000\0" \ + "bootfile=zImage\0" \ + "console=ttyO0,115200n8\0" \ + "optargs=\0" \ + "rootpath=/tftpboot/tseries/rootfs-small\0" \ + "nfsopts=nolock\0" \ + "netargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=/dev/nfs " \ + "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \ + "ip=dhcp\0" \ + "netboot=echo Booting from network ...; " \ + "setenv autoload no; " \ + "dhcp; " \ + "tftp ${loadaddr} ${bootfile}; " \ + "run netargs; " \ + "bootm ${loadaddr}\0" \ + "usbupdate=echo Updating UBOOT from USB-Stick ...; " \ + "usb start; " \ + "fatload usb 0 0x80000000 updateubootusb.img; " \ + "source;\0" \ + "netupdate=echo Updating UBOOT from Network (TFTP) ...; " \ + "setenv autoload 0; " \ + "dhcp;" \ + "tftp 0x80000000 updateUBOOT.img;" \ + "source;\0" \ + NANDARGS \ + MMCARGS +#endif /* !CONFIG_SPL_BUILD*/ + +#define CONFIG_BOOTCOMMAND \ + "run mmcboot1;" +#define CONFIG_BOOTDELAY 1 /* TODO: für release auf 0 setzen */ + +#ifdef CONFIG_NAND +/* + * GPMC block. We support 1 device and the physical address to + * access CS0 at is 0x8000000. + */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE 0x8000000 +#define CONFIG_NAND_OMAP_GPMC +#define CONFIG_CMD_NAND +/* don't change OMAP_ELM, ECCSCHEME. ROM code only supports this */ +#define CONFIG_NAND_OMAP_ELM +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW +#define GPMC_NAND_ECC_LP_x16_LAYOUT 1 +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ + CONFIG_SYS_NAND_PAGE_SIZE) +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS +#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9, \ + 10, 11, 12, 13, 14, 15, 16, 17, \ + 18, 19, 20, 21, 22, 23, 24, 25, \ + 26, 27, 28, 29, 30, 31, 32, 33, \ + 34, 35, 36, 37, 38, 39, 40, 41, \ + 42, 43, 44, 45, 46, 47, 48, 49, \ + 50, 51, 52, 53, 54, 55, 56, 57, } + +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 14 + +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 + +#define MTDIDS_DEFAULT "nand0=omap2-nand.0" +#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:" \ + "128k(SPL)," \ + "128k(SPL.backup1)," \ + "128k(SPL.backup2)," \ + "128k(SPL.backup3)," \ + "512k(u-boot)," \ + "128k(u-boot-spl-os)," \ + "128k(u-boot-env)," \ + "5m(kernel),"\ + "-(rootfs)" +#endif /* CONFIG_NAND */ + +/* USB configuration */ +#define CONFIG_USB_MUSB_DSPS +#define CONFIG_ARCH_MISC_INIT +#define CONFIG_MUSB_PIO_ONLY +#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT +/* attention! not only for gadget, enables also highspeed in hostmode */ +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_MUSB_HOST +#define CONFIG_AM335X_USB0 +#define CONFIG_AM335X_USB0_MODE MUSB_HOST +#define CONFIG_AM335X_USB1 +#define CONFIG_AM335X_USB1_MODE MUSB_HOST + +#ifdef CONFIG_MUSB_HOST +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#endif /* CONFIG_MUSB_HOST */ + +#if defined(CONFIG_SPI_BOOT) +/* McSPI IP block */ +#define CONFIG_SPI +#define CONFIG_OMAP3_SPI +#define CONFIG_CMD_SPI +#define CONFIG_CMD_SF +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SF_DEFAULT_SPEED 24000000 + +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_LOAD +#define CONFIG_SPL_SPI_BUS 0 +#define CONFIG_SPL_SPI_CS 0 +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 +#undef CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT +#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED +#define CONFIG_ENV_SECT_SIZE (4 << 10) /* 4 KB sectors */ +#define CONFIG_ENV_OFFSET (768 << 10) /* 768 KiB in */ +#define CONFIG_ENV_OFFSET_REDUND (896 << 10) /* 896 KiB in */ + +#elif defined(CONFIG_EMMC_BOOT) +#undef CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 1 +#define CONFIG_SYS_MMC_ENV_PART 2 +#define CONFIG_ENV_OFFSET 0x40000 /* TODO: Adresse definieren */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT + +#elif defined(CONFIG_NAND) +#undef CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x120000 /* TODO: Adresse definieren */ +#define CONFIG_SYS_ENV_SECT_SIZE CONFIG_ENV_SIZE +#else +#error "no storage for Environment defined!" +#endif +/* + * Common filesystems support. When we have removable storage we + * enabled a number of useful commands and support. + */ +#if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE) +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_FAT +#define CONFIG_FAT_WRITE +#define CONFIG_CMD_FS_GENERIC +#endif /* CONFIG_MMC, ... */ + +#endif /* ! __CONFIG_TSERIES_H__ */ diff --git a/include/configs/u8500_href.h b/include/configs/u8500_href.h index 629299d107..8d7970a376 100644 --- a/include/configs/u8500_href.h +++ b/include/configs/u8500_href.h @@ -29,7 +29,6 @@ #define CONFIG_ENV_SIZE (128*1024) #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256*1024) #endif -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* for initial data */ /* * PL011 Configuration diff --git a/include/configs/udoo.h b/include/configs/udoo.h index 7f09489118..4f518527a0 100644 --- a/include/configs/udoo.h +++ b/include/configs/udoo.h @@ -199,7 +199,6 @@ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_SYS_HZ 1000 #define CONFIG_CMDLINE_EDITING diff --git a/include/configs/usb_a9263.h b/include/configs/usb_a9263.h index c4d04dec38..3c54870783 100644 --- a/include/configs/usb_a9263.h +++ b/include/configs/usb_a9263.h @@ -20,7 +20,6 @@ /* ARM asynchronous clock */ #define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* 12 MHz crystal */ #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 -#define CONFIG_SYS_HZ 1000 #define CONFIG_MACH_TYPE MACH_TYPE_USB_A9263 diff --git a/include/configs/venice2.h b/include/configs/venice2.h new file mode 100644 index 0000000000..91808e9203 --- /dev/null +++ b/include/configs/venice2.h @@ -0,0 +1,79 @@ +/* + * (C) Copyright 2013-2014 + * NVIDIA Corporation <www.nvidia.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/sizes.h> + +#include "tegra124-common.h" + +/* Enable fdt support for Venice2. Flash the image in u-boot-dtb.bin */ +#define CONFIG_DEFAULT_DEVICE_TREE tegra124-venice2 +#define CONFIG_OF_CONTROL +#define CONFIG_OF_SEPARATE + +/* High-level configuration options */ +#define V_PROMPT "Tegra124 (Venice2) # " +#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Venice2" + +/* Board-specific serial config */ +#define CONFIG_SERIAL_MULTI +#define CONFIG_TEGRA_ENABLE_UARTA +#define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTA_BASE + +#define CONFIG_BOARD_EARLY_INIT_F + +/* I2C */ +#define CONFIG_SYS_I2C_TEGRA +#define CONFIG_SYS_I2C_INIT_BOARD +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_MAX_I2C_BUS TEGRA_I2C_NUM_CONTROLLERS +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C + +/* SD/MMC */ +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_TEGRA_MMC +#define CONFIG_CMD_MMC + +/* Environment in eMMC, at the end of 2nd "boot sector" */ +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_SYS_MMC_ENV_PART 2 +#define CONFIG_ENV_OFFSET (-CONFIG_ENV_SIZE) + +/* SPI */ +#define CONFIG_TEGRA114_SPI /* Compatible w/ Tegra114 SPI */ +#define CONFIG_TEGRA114_SPI_CTRLS 6 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_WINBOND +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 +#define CONFIG_SF_DEFAULT_SPEED 24000000 +#define CONFIG_CMD_SPI +#define CONFIG_CMD_SF +#define CONFIG_SPI_FLASH_SIZE (4 << 20) + +/* USB Host support */ +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_TEGRA +#define CONFIG_USB_STORAGE +#define CONFIG_CMD_USB + +/* USB networking support */ +#define CONFIG_USB_HOST_ETHER +#define CONFIG_USB_ETHER_ASIX + +/* General networking support */ +#define CONFIG_CMD_NET +#define CONFIG_CMD_DHCP + +#include "tegra-common-post.h" + +#endif /* __CONFIG_H */ diff --git a/include/configs/vl_ma2sc.h b/include/configs/vl_ma2sc.h index 88aaa95fb1..14c6e675c1 100644 --- a/include/configs/vl_ma2sc.h +++ b/include/configs/vl_ma2sc.h @@ -322,7 +322,6 @@ #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) /* our CLE is AD22 */ #define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PD(15) #define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PB(0) -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif /* Ethernet */ @@ -363,7 +362,6 @@ */ #define CONFIG_SYS_MALLOC_LEN \ ROUND(3 * CONFIG_ENV_SIZE + 128 * 1024, 0x1000) -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* 128 bytes for initial data */ #ifndef CONFIG_RAMLOAD #define CONFIG_BOOTCOMMAND "run nfsboot" diff --git a/include/configs/x600.h b/include/configs/x600.h index 39540e3806..7405419f0e 100644 --- a/include/configs/x600.h +++ b/include/configs/x600.h @@ -74,10 +74,9 @@ /* Ethernet config options */ #define CONFIG_MII #define CONFIG_DESIGNWARE_ETH -#define CONFIG_DW_SEARCH_PHY #define CONFIG_NET_MULTI +#define CONFIG_PHYLIB #define CONFIG_PHY_RESET_DELAY 10000 /* in usec */ -#define CONFIG_DW_AUTONEG #define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ @@ -86,6 +85,7 @@ /* I2C config options */ #define CONFIG_HARD_I2C #define CONFIG_DW_I2C +#define CONFIG_SYS_I2C_BASE 0xD0200000 #define CONFIG_SYS_I2C_SPEED 400000 #define CONFIG_SYS_I2C_SLAVE 0x02 #define CONFIG_I2C_CHIPADDRESS 0x50 @@ -171,7 +171,6 @@ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE #define CONFIG_SYS_LOAD_ADDR 0x00800000 #define CONFIG_SYS_CONSOLE_INFO_QUIET -#define CONFIG_SYS_64BIT_VSPRINTF /* Use last 2 lwords in internal SRAM for bootcounter */ #define CONFIG_BOOTCOUNT_LIMIT diff --git a/include/configs/xfi3.h b/include/configs/xfi3.h index 022bc95927..8e6b365364 100644 --- a/include/configs/xfi3.h +++ b/include/configs/xfi3.h @@ -55,7 +55,7 @@ #define CONFIG_EHCI_MXS_PORT0 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 -#define CONFIG_MV_UDC /* ChipIdea CI13xxx UDC */ +#define CONFIG_CI_UDC /* ChipIdea CI13xxx UDC */ #define CONFIG_USB_GADGET_DUALSPEED #define CONFIG_USB_ETHER diff --git a/include/configs/zipitz2.h b/include/configs/zipitz2.h index e38fa89fda..41a7c99edc 100644 --- a/include/configs/zipitz2.h +++ b/include/configs/zipitz2.h @@ -138,7 +138,6 @@ unsigned char zipitz2_spi_read(void); * Clock Configuration */ #undef CONFIG_SYS_CLKS_IN_HZ -#define CONFIG_SYS_HZ 1000 #define CONFIG_SYS_CPUSPEED 0x190 /* standard setting for 312MHz; L=16, N=1.5, A=0, SDCLK!=SystemBus */ /* diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h index e7a8e9fb11..14f0b90b9b 100644 --- a/include/configs/zynq-common.h +++ b/include/configs/zynq-common.h @@ -35,27 +35,12 @@ #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} -/* Zynq Serial driver */ -#ifdef CONFIG_ZYNQ_SERIAL_UART0 -# define CONFIG_ZYNQ_SERIAL_BASEADDR0 0xE0000000 -# define CONFIG_ZYNQ_SERIAL_BAUDRATE0 CONFIG_BAUDRATE -# define CONFIG_ZYNQ_SERIAL_CLOCK0 50000000 -#endif - -#ifdef CONFIG_ZYNQ_SERIAL_UART1 -# define CONFIG_ZYNQ_SERIAL_BASEADDR1 0xE0001000 -# define CONFIG_ZYNQ_SERIAL_BAUDRATE1 CONFIG_BAUDRATE -# define CONFIG_ZYNQ_SERIAL_CLOCK1 50000000 -#endif - -#if defined(CONFIG_ZYNQ_SERIAL_UART0) || defined(CONFIG_ZYNQ_SERIAL_UART1) -# define CONFIG_ZYNQ_SERIAL -#endif - /* DCC driver */ #if defined(CONFIG_ZYNQ_DCC) # define CONFIG_ARM_DCC # define CONFIG_CPU_V6 /* Required by CONFIG_ARM_DCC */ +#else +# define CONFIG_ZYNQ_SERIAL #endif /* Ethernet driver */ @@ -104,13 +89,13 @@ # define CONFIG_DOS_PARTITION #endif +#define CONFIG_SYS_I2C_ZYNQ /* I2C */ -#if defined(CONFIG_ZYNQ_I2C0) || defined(CONFIG_ZYNQ_I2C1) +#if defined(CONFIG_SYS_I2C_ZYNQ) # define CONFIG_CMD_I2C # define CONFIG_SYS_I2C -# define CONFIG_SYS_I2C_ZYNQ # define CONFIG_SYS_I2C_ZYNQ_SPEED 100000 -# define CONFIG_SYS_I2C_ZYNQ_SLAVE 1 +# define CONFIG_SYS_I2C_ZYNQ_SLAVE 0 #endif /* EEPROM */ @@ -164,7 +149,7 @@ "fatload mmc 0 ${load_addr} ${fit_image} && " \ "bootm ${load_addr}\0" \ "jtagboot=echo TFTPing FIT to RAM... && " \ - "tftp ${load_addr} ${fit_image} && " \ + "tftpboot ${load_addr} ${fit_image} && " \ "bootm ${load_addr}\0" #define CONFIG_BOOTCOMMAND "run $modeboot" #define CONFIG_BOOTDELAY 3 /* -1 to Disable autoboot */ @@ -178,6 +163,8 @@ #define CONFIG_AUTO_COMPLETE #define CONFIG_BOARD_LATE_INIT #define CONFIG_SYS_LONGHELP +#define CONFIG_CLOCKS +#define CONFIG_CMD_CLK #define CONFIG_SYS_MAXARGS 15 /* max number of command args */ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ @@ -221,6 +208,9 @@ #define CONFIG_FIT_SIGNATURE #define CONFIG_RSA +/* Extend size of kernel image for uncompression */ +#define CONFIG_SYS_BOOTM_LEN (20 * 1024 * 1024) + /* Boot FreeBSD/vxWorks from an ELF image */ #if defined(CONFIG_ZYNQ_BOOT_FREEBSD) # define CONFIG_API @@ -228,11 +218,91 @@ # define CONFIG_SYS_MMC_MAX_DEVICE 1 #endif +#define CONFIG_SYS_LDSCRIPT "arch/arm/cpu/armv7/zynq/u-boot.lds" + /* Commands */ #include <config_cmd_default.h> #define CONFIG_CMD_PING #define CONFIG_CMD_DHCP #define CONFIG_CMD_MII +#define CONFIG_CMD_TFTPPUT + +/* SPL part */ +#define CONFIG_SPL +#define CONFIG_CMD_SPL +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT + +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/zynq/u-boot-spl.lds" + +/* Disable dcache for SPL just for sure */ +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_DCACHE_OFF +#undef CONFIG_FPGA +#endif + +/* MMC support */ +#ifdef CONFIG_ZYNQ_SDHCI0 +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ +#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1 +#define CONFIG_SPL_LIBDISK_SUPPORT +#define CONFIG_SPL_FAT_SUPPORT +#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" +#endif + +/* Address in RAM where the parameters must be copied by SPL. */ +#define CONFIG_SYS_SPL_ARGS_ADDR 0x10000000 + +#define CONFIG_SPL_FAT_LOAD_ARGS_NAME "system.dtb" +#define CONFIG_SPL_FAT_LOAD_KERNEL_NAME "uImage" + +/* Not using MMC raw mode - just for compilation purpose */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0 +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0 +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0 + +/* qspi mode is working fine */ +#ifdef CONFIG_ZYNQ_QSPI +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_LOAD +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_BUS 0 +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x100000 +#define CONFIG_SPL_SPI_CS 0 +#endif + +/* for booting directly linux */ +#define CONFIG_SPL_OS_BOOT + +/* SP location before relocation, must use scratch RAM */ +#define CONFIG_SPL_TEXT_BASE 0x0 + +/* 3 * 64kB blocks of OCM - one is on the top because of bootrom */ +#define CONFIG_SPL_MAX_SIZE 0x30000 + +/* The highest 64k OCM address */ +#define OCM_HIGH_ADDR 0xffff0000 + +/* Just define any reasonable size */ +#define CONFIG_SPL_STACK_SIZE 0x1000 + +/* SPL stack position - and stack goes down */ +#define CONFIG_SPL_STACK (OCM_HIGH_ADDR + CONFIG_SPL_STACK_SIZE) + +/* On the top of OCM space */ +#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_STACK + \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x1000 + +/* BSS setup */ +#define CONFIG_SPL_BSS_START_ADDR 0x100000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x100000 + +#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE #endif /* __CONFIG_ZYNQ_COMMON_H */ diff --git a/include/configs/zynq_zc70x.h b/include/configs/zynq_zc70x.h index 673660e659..de0e24129c 100644 --- a/include/configs/zynq_zc70x.h +++ b/include/configs/zynq_zc70x.h @@ -2,7 +2,7 @@ * (C) Copyright 2013 Xilinx, Inc. * * Configuration settings for the Xilinx Zynq ZC702 and ZC706 boards - * See zynq_common.h for Zynq common configs + * See zynq-common.h for Zynq common configs * * SPDX-License-Identifier: GPL-2.0+ */ diff --git a/include/configs/zynq_zed.h b/include/configs/zynq_zed.h index 412dede533..274140cb3f 100644 --- a/include/configs/zynq_zed.h +++ b/include/configs/zynq_zed.h @@ -2,7 +2,7 @@ * (C) Copyright 2013 Xilinx, Inc. * * Configuration for Zynq Evaluation and Development Board - ZedBoard - * See zynq_common.h for Zynq common configs + * See zynq-common.h for Zynq common configs * * SPDX-License-Identifier: GPL-2.0+ */ |
