arm: at91: add support for mini-box picosam9g45 board

Bootlog:
U-Boot SPL 2015.10-rc1-00452-g96a7ed1 (Aug 17 2015 - 10:32:21)
mci: setting clock 258000 Hz, block size 512
mci: setting clock 258000 Hz, block size 512
mci: setting clock 258000 Hz, block size 512
mci: setting clock 33024000 Hz, block size 512
reading u-boot.img
reading u-boot.img

U-Boot 2015.10-rc1-00452-g96a7ed1 (Aug 17 2015 - 10:32:21 +0000)

CPU: AT91SAM9G45
Crystal frequency:       12 MHz
CPU clock        :      400 MHz
Master clock     :  133.333 MHz
       Watchdog enabled
DRAM:  256 MiB
WARNING: Caches not enabled
MMC:   mci: 0
mci: setting clock 260416 Hz, block size 512
mci: setting clock 260416 Hz, block size 512
mci: setting clock 260416 Hz, block size 512
mci: setting clock 33333333 Hz, block size 512
reading uboot.env
In:    serial
Out:   serial
Err:   serial
Net:   macb0
Error: macb0 address not set.

Hit any key to stop autoboot:  0
U-Boot>

Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[add 'picosam9g45_defconfig' to MAINTAINERS]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

1 files changed, 211 insertions, 0 deletions

diff --git a/include/configs/picosam9g45.h b/include/configs/picosam9g45.h
new file mode 100644
index 0000000000..e3039c2a5d
--- /dev/null
+++ b/include/configs/picosam9g45.h
@@ -0,0 +1,211 @@
+/*
+ * Configuration settings for the mini-box PICOSAM9G45 board.
+ * (C) Copyright 2015 Inter Act B.V.
+ *
+ * Based on:
+ * U-Boot file: include/configs/at91sam9m10g45ek.h
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian@popies.net>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/hardware.h>
+
+#define CONFIG_SYS_TEXT_BASE		0x23f00000
+
+#define CONFIG_ATMEL_LEGACY		/* required until (g)pio is fixed */
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_SLOW_CLOCK      32768
+#define CONFIG_SYS_AT91_MAIN_CLOCK      12000000 /* from 12 MHz crystal */
+
+#define CONFIG_PICOSAM
+
+#define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs	*/
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_DISPLAY_CPUINFO
+
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_OF_LIBFDT
+
+#define CONFIG_SYS_GENERIC_BOARD
+
+/* general purpose I/O */
+#define CONFIG_ATMEL_LEGACY		/* required until (g)pio is fixed */
+#define CONFIG_AT91_GPIO
+#define CONFIG_AT91_GPIO_PULLUP	1	/* keep pullups on peripheral pins */
+
+/* serial console */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE		ATMEL_BASE_DBGU
+#define	CONFIG_USART_ID			ATMEL_ID_SYS
+
+/* LCD */
+#define CONFIG_LCD
+#define LCD_BPP				LCD_COLOR8
+#define CONFIG_LCD_LOGO
+#undef LCD_TEST_PATTERN
+#define CONFIG_LCD_INFO
+#define CONFIG_LCD_INFO_BELOW_LOGO
+#define CONFIG_SYS_WHITE_ON_BLACK
+#define CONFIG_ATMEL_LCD
+#define CONFIG_ATMEL_LCD_RGB565
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+/* board specific(not enough SRAM) */
+#define CONFIG_AT91SAM9G45_LCD_BASE		0x23E00000
+
+/* LED */
+#define CONFIG_AT91_LED
+#define CONFIG_GREEN_LED	AT91_PIN_PD31	/* this is the user1 led */
+
+#define CONFIG_BOOTDELAY	3
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/* Enable the watchdog */
+#define CONFIG_AT91SAM9_WATCHDOG
+#define CONFIG_HW_WATCHDOG
+
+/*
+ * Command line configuration.
+ */
+
+/* No NOR flash */
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_USB
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS	2
+#define PHYS_SDRAM_1		ATMEL_BASE_CS1	/* on DDRSDRC1 */
+#define PHYS_SDRAM_1_SIZE	0x08000000	/* 128 MB */
+#define PHYS_SDRAM_2		ATMEL_BASE_CS6	/* on DDRSDRC0 */
+#define PHYS_SDRAM_2_SIZE       0x08000000	/* 128 MB */
+#define CONFIG_SYS_SDRAM_BASE	PHYS_SDRAM_1
+
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+
+/* MMC */
+#define CONFIG_CMD_MMC
+
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_GENERIC_ATMEL_MCI
+#endif
+
+#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Ethernet */
+#define CONFIG_MACB
+#define CONFIG_RMII
+#define CONFIG_NET_RETRY_COUNT		20
+#define CONFIG_RESET_PHY_R
+#define CONFIG_AT91_WANTS_COMMON_PHY
+
+/* USB */
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_ATMEL
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	2
+#define CONFIG_USB_STORAGE
+
+#define CONFIG_SYS_LOAD_ADDR		0x22000000	/* load address */
+
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		0x23e00000
+
+#ifdef CONFIG_SYS_USE_MMC
+/* bootstrap + u-boot + env + linux in mmc */
+#define FAT_ENV_INTERFACE	"mmc"
+/*
+ * We don't specify the part number, if device 0 has partition table, it means
+ * the first partition; it no partition table, then take whole device as a
+ * FAT file system.
+ */
+#define FAT_ENV_DEVICE_AND_PART	"0"
+#define FAT_ENV_FILE		"uboot.env"
+#define CONFIG_ENV_IS_IN_FAT
+#define CONFIG_FAT_WRITE
+#define CONFIG_ENV_SIZE		0x4000
+
+#define CONFIG_BOOTARGS		"console=ttyS0,115200 " \
+				"root=/dev/mmcblk0p2 rw rootwait"
+#define CONFIG_BOOTCOMMAND	"fatload mmc 0:1 0x21000000 dtb; " \
+				"fatload mmc 0:1 0x22000000 zImage; " \
+				"bootz 0x22000000 - 0x21000000"
+#endif
+
+#define CONFIG_BAUDRATE			115200
+
+#define CONFIG_SYS_PROMPT	"U-Boot> "
+#define CONFIG_SYS_CBSIZE	256
+#define CONFIG_SYS_MAXARGS	16
+#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE  \
+					+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_HUSH_PARSER
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN	ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
+
+/* Defines for SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE		0x300000
+#define CONFIG_SPL_MAX_SIZE		0x010000
+#define CONFIG_SPL_STACK		0x310000
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SPL_WATCHDOG_SUPPORT
+
+#define CONFIG_SYS_MONITOR_LEN		0x80000
+
+#ifdef CONFIG_SYS_USE_MMC
+
+#define CONFIG_SPL_BSS_START_ADDR	0x20000000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x00080000
+#define CONFIG_SYS_SPL_MALLOC_START	0x20080000
+#define CONFIG_SYS_SPL_MALLOC_SIZE	0x00080000
+
+#define CONFIG_SPL_LDSCRIPT	arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	0x400
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+
+#define CONFIG_SPL_ATMEL_SIZE
+#define CONFIG_SYS_MASTER_CLOCK		132096000
+#define CONFIG_SYS_AT91_PLLA		0x20c73f03
+#define CONFIG_SYS_MCKR			0x1301
+#define CONFIG_SYS_MCKR_CSS		0x1302
+
+#endif
+#endif