Merge branch 'u-boot/master' into 'u-boot-arm/master'

1 files changed, 121 insertions, 121 deletions

diff --git a/include/configs/ls2085a_common.h b/include/configs/ls2085a_common.h
index e0435cc0a7..e270fc8c19 100644
--- a/include/configs/ls2085a_common.h
+++ b/include/configs/ls2085a_common.h
@@ -19,8 +19,20 @@
 #define CONFIG_ARM_ERRATA_828024
 #define CONFIG_ARM_ERRATA_826974
 
+#include <asm/arch-fsl-lsch3/config.h>
+#if (defined(CONFIG_SYS_FSL_SRDS_1) || defined(CONFIG_SYS_FSL_SRDS_2))
+#define	CONFIG_SYS_HAS_SERDES
+#endif
+
+/* We need architecture specific misc initializations */
+#define CONFIG_ARCH_MISC_INIT
+
 /* Link Definitions */
-#define CONFIG_SYS_TEXT_BASE		0x30001000
+#ifdef CONFIG_SPL
+#define CONFIG_SYS_TEXT_BASE		0x80400000
+#else
+#define CONFIG_SYS_TEXT_BASE		0x30100000
+#endif
 
 #ifdef CONFIG_EMU
 #define CONFIG_SYS_NO_FLASH
@@ -39,13 +51,13 @@
 #define CONFIG_FIT
 #define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
 
+#ifndef CONFIG_SPL
 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
+#endif
 #ifndef CONFIG_SYS_FSL_DDR4
 #define CONFIG_SYS_FSL_DDR3		/* Use DDR3 memory */
 #define CONFIG_SYS_DDR_RAW_TIMING
 #endif
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	4
 
 #define CONFIG_SYS_FSL_DDR_INTLV_256B	/* force 256 byte interleaving */
 
@@ -69,23 +81,26 @@
 #define CONFIG_SYS_DP_DDR_BASE_PHY	0
 #define CONFIG_DP_DDR_CTRL		2
 #define CONFIG_DP_DDR_NUM_CTRLS		1
-#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR	1
 
 /* Generic Timer Definitions */
-#define COUNTER_FREQUENCY		12000000	/* 12MHz */
+/*
+ * This is not an accurate number. It is used in start.S. The frequency
+ * will be udpated later when get_bus_freq(0) is available.
+ */
+#define COUNTER_FREQUENCY		25000000	/* 25MHz */
 
 /* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 128 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2048 * 1024)
 
 /* I2C */
 #define CONFIG_CMD_I2C
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_MXC_I2C1_SPEED	40000000
-#define CONFIG_SYS_MXC_I2C2_SPEED	40000000
+#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
+#define CONFIG_SYS_I2C_MXC_I2C4		/* enable I2C bus 4 */
 
 /* Serial Port */
-#define CONFIG_CONS_INDEX       2
+#define CONFIG_CONS_INDEX       1
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE     1
@@ -96,131 +111,98 @@
 
 /* IFC */
 #define CONFIG_FSL_IFC
-#define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
-#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
+
 /*
- * During booting, CS0 needs to be at the region of 0x30000000, i.e. the IFC
- * address 0. But this region is limited to 256MB. To accommodate bigger NOR
- * flash and other devices, we will map CS0 to 0x580000000 after relocation.
+ * During booting, IFC is mapped at the region of 0x30000000.
+ * But this region is limited to 256MB. To accommodate NOR, promjet
+ * and FPGA. This region is divided as below:
+ * 0x30000000 - 0x37ffffff : 128MB : NOR flash
+ * 0x38000000 - 0x3BFFFFFF : 64MB  : Promjet
+ * 0x3C000000 - 0x40000000 : 64MB  : FPGA etc
+ *
+ * To accommodate bigger NOR flash and other devices, we will map IFC
+ * chip selects to as below:
+ * 0x5_1000_0000..0x5_1fff_ffff	Memory Hole
+ * 0x5_2000_0000..0x5_3fff_ffff	IFC CSx (FPGA, NAND and others 512MB)
+ * 0x5_4000_0000..0x5_7fff_ffff	ASIC or others 1GB
+ * 0x5_8000_0000..0x5_bfff_ffff	IFC CS0 1GB (NOR/Promjet)
+ * 0x5_C000_0000..0x5_ffff_ffff	IFC CS1 1GB (NOR/Promjet)
+ *
+ * For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
  * CONFIG_SYS_FLASH_BASE has the final address (core view)
  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
  * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
  */
+
 #define CONFIG_SYS_FLASH_BASE			0x580000000ULL
 #define CONFIG_SYS_FLASH_BASE_PHYS		0x80000000
 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000
 
-/*
- * NOR Flash Timing Params
- */
-#define CONFIG_SYS_NOR0_CSPR					\
-	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)		| \
-	CSPR_PORT_SIZE_16					| \
-	CSPR_MSEL_NOR						| \
-	CSPR_V)
-#define CONFIG_SYS_NOR0_CSPR_EARLY				\
-	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)	| \
-	CSPR_PORT_SIZE_16					| \
-	CSPR_MSEL_NOR						| \
-	CSPR_V)
-#define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(12)
-#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x1) | \
-				FTIM0_NOR_TEADC(0x1) | \
-				FTIM0_NOR_TEAHC(0x1))
-#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x1) | \
-				FTIM1_NOR_TRAD_NOR(0x1))
-#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x0) | \
-				FTIM2_NOR_TCH(0x0) | \
-				FTIM2_NOR_TWP(0x1))
-#define CONFIG_SYS_NOR_FTIM3	0x04000000
-#define CONFIG_SYS_IFC_CCR	0x01000000
+#define CONFIG_SYS_FLASH1_BASE_PHYS		0xC0000000
+#define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY	0x8000000
 
 #ifndef CONFIG_SYS_NO_FLASH
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 #define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+#endif
 
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
+#ifndef __ASSEMBLY__
+unsigned long long get_qixis_addr(void);
 #endif
+#define QIXIS_BASE				get_qixis_addr()
+#define QIXIS_BASE_PHYS				0x20000000
+#define QIXIS_BASE_PHYS_EARLY			0xC000000
+#define QIXIS_STAT_PRES1			0xb
+#define QIXIS_SDID_MASK				0x07
+#define QIXIS_ESDHC_NO_ADAPTER			0x7
+
+#define CONFIG_SYS_NAND_BASE			0x530000000ULL
+#define CONFIG_SYS_NAND_BASE_PHYS		0x30000000
 
-#define CONFIG_NAND_FSL_IFC
-#define CONFIG_SYS_NAND_MAX_ECCPOS	256
-#define CONFIG_SYS_NAND_MAX_OOBFREE	2
-#define CONFIG_SYS_NAND_BASE		0x520000000
-#define CONFIG_SYS_NAND_BASE_PHYS	0x20000000
-
-#define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
-#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
-				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
-				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
-				| CSPR_V)
-#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64 * 1024)
-
-#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
-				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
-				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
-				| CSOR_NAND_RAL_3	/* RAL = 2Byes */ \
-				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \
-				| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
-				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
-
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/* ONFI NAND Flash mode0 Timing Params */
-#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
-					FTIM0_NAND_TWP(0x18)   | \
-					FTIM0_NAND_TWCHT(0x07) | \
-					FTIM0_NAND_TWH(0x0a))
-#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
-					FTIM1_NAND_TWBE(0x39)  | \
-					FTIM1_NAND_TRR(0x0e)   | \
-					FTIM1_NAND_TRP(0x18))
-#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
-					FTIM2_NAND_TREH(0x0a) | \
-					FTIM2_NAND_TWHRE(0x1e))
-#define CONFIG_SYS_NAND_FTIM3		0x0
-
-#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_CMD_NAND
-
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
-
-#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR_EARLY
-#define CONFIG_SYS_CSPR0_FINAL		CONFIG_SYS_NOR0_CSPR
-#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+/* Debug Server firmware */
+#define CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE	(512UL * 1024 * 1024)
+/* 2 sec timeout */
+#define CONFIG_SYS_DEBUG_SERVER_TIMEOUT			(2 * 1000 * 1000)
 
 /* MC firmware */
 #define CONFIG_FSL_MC_ENET
 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE	(512UL * 1024 * 1024)
-#define CONFIG_SYS_LS_MC_FW_IN_NOR
-#define CONFIG_SYS_LS_MC_FW_ADDR	0x580200000ULL
-#define CONFIG_SYS_LS_MC_DPL_IN_NOR
-#define CONFIG_SYS_LS_MC_DPL_ADDR	0x5806C0000ULL
 /* TODO Actual DPL max length needs to be confirmed with the MC FW team */
-#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH	(256 * 1024)
-#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET    0xe00000
-
-/* Carve the MC private DRAM block from the end of DRAM */
-#ifdef CONFIG_FSL_MC_ENET
-#define CONFIG_SYS_MEM_TOP_HIDE		mc_get_dram_block_size()
+#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH	    0x20000
+#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET    0x00F00000
+#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH	    0x20000
+#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET    0x00F20000
+
+/* Carve out a DDR region which will not be used by u-boot/Linux */
+#if defined(CONFIG_FSL_MC_ENET) || defined(CONFIG_FSL_DEBUG_SERVER)
+#define CONFIG_SYS_MEM_TOP_HIDE		get_dram_size_to_hide()
 #endif
 
+/* PCIe */
+#define CONFIG_PCIE1		/* PCIE controler 1 */
+#define CONFIG_PCIE2		/* PCIE controler 2 */
+#define CONFIG_PCIE3		/* PCIE controler 3 */
+#define CONFIG_PCIE4		/* PCIE controler 4 */
+#define FSL_PCIE_COMPAT "fsl,20851a-pcie"
+
+#define CONFIG_SYS_PCI_64BIT
+
+#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF	0x00000000
+#define CONFIG_SYS_PCIE_CFG0_SIZE	0x00001000	/* 4k */
+#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF	0x00001000
+#define CONFIG_SYS_PCIE_CFG1_SIZE	0x00001000	/* 4k */
+
+#define CONFIG_SYS_PCIE_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE_IO_PHYS_OFF	0x00010000
+#define CONFIG_SYS_PCIE_IO_SIZE		0x00010000	/* 64k */
+
+#define CONFIG_SYS_PCIE_MEM_BUS		0x40000000
+#define CONFIG_SYS_PCIE_MEM_PHYS_OFF	0x40000000
+#define CONFIG_SYS_PCIE_MEM_SIZE	0x40000000	/* 1G */
+
 /* Command line configuration */
 #define CONFIG_CMD_CACHE
 #define CONFIG_CMD_BDI
@@ -228,6 +210,7 @@
 #define CONFIG_CMD_ENV
 #define CONFIG_CMD_FLASH
 #define CONFIG_CMD_IMI
+#define CONFIG_CMD_LOADB
 #define CONFIG_CMD_MEMORY
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NET
@@ -237,8 +220,6 @@
 #define CONFIG_CMD_BOOTD
 #define CONFIG_CMD_ECHO
 #define CONFIG_CMD_SOURCE
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
 
 /* Miscellaneous configurable options */
 #define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
@@ -247,9 +228,6 @@
 /* Physical Memory Map */
 /* fixme: these need to be checked against the board */
 #define CONFIG_CHIP_SELECTS_PER_CTRL	4
-#define CONFIG_SYS_CLK_FREQ	100000000
-#define CONFIG_DDR_CLK_FREQ	133333333
-
 
 #define CONFIG_NR_DRAM_BANKS		3
 
@@ -265,7 +243,7 @@
 	"kernel_addr=0x100000\0"		\
 	"ramdisk_addr=0x800000\0"		\
 	"ramdisk_size=0x2000000\0"		\
-	"fdt_high=0xffffffffffffffff\0"		\
+	"fdt_high=0xa0000000\0"			\
 	"initrd_high=0xffffffffffffffff\0"	\
 	"kernel_start=0x581200000\0"		\
 	"kernel_load=0xa0000000\0"		\
@@ -278,15 +256,11 @@
 				"hugepages=16"
 #define CONFIG_BOOTCOMMAND		"cp.b $kernel_start $kernel_load "     \
 					"$kernel_size && bootm $kernel_load"
-#define CONFIG_BOOTDELAY		1
-
-/* Store environment at top of flash */
-#define CONFIG_ENV_IS_NOWHERE		1
-#define CONFIG_ENV_SIZE			0x1000
+#define CONFIG_BOOTDELAY		10
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
-#define CONFIG_SYS_PROMPT		"> "
+#define CONFIG_SYS_PROMPT		"=> "
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_HUSH_PARSER
@@ -294,10 +268,36 @@
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE /* Boot args buffer */
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_CMDLINE_EDITING		1
+#define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_MAXARGS		64	/* max command args */
 
 #ifndef __ASSEMBLY__
-unsigned long mc_get_dram_block_size(void);
+unsigned long get_dram_size_to_hide(void);
 #endif
 
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
+#define CONFIG_SPL_BSS_START_ADDR	0x80100000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x00100000
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_MAX_SIZE		0x16000
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_STACK		(CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
+#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
+#define CONFIG_SPL_TEXT_BASE		0x1800a000
+
+#define CONFIG_SYS_NAND_U_BOOT_DST	0x80400000
+#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST
+#define CONFIG_SYS_SPL_MALLOC_SIZE	0x00100000
+#define CONFIG_SYS_SPL_MALLOC_START	0x80200000
+#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+
 #endif /* __LS2_COMMON_H */