Blackfin: ibf-dsp561: new board port

Signed-off-by: Hoan Hoang <hnhoan@i-syst.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

1 files changed, 130 insertions, 0 deletions

diff --git a/include/configs/ibf-dsp561.h b/include/configs/ibf-dsp561.h
new file mode 100644
index 0000000000..6d03c4ca76
--- /dev/null
+++ b/include/configs/ibf-dsp561.h
@@ -0,0 +1,130 @@
+/*
+ * U-boot - Configuration file for IBF-DSP561 board
+ */
+
+#ifndef __CONFIG_IBF_DSP561__H__
+#define __CONFIG_IBF_DSP561__H__
+
+#include <asm/blackfin-config-pre.h>
+
+
+/*
+ * Processor Settings
+ */
+#define CONFIG_BFIN_CPU             bf561-0.5
+#define CONFIG_BFIN_BOOT_MODE       BFIN_BOOT_BYPASS
+
+
+/*
+ * Clock Settings
+ *	CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ *	SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
+ */
+/* CONFIG_CLKIN_HZ is any value in Hz					*/
+#define CONFIG_CLKIN_HZ			25000000
+/* CLKIN_HALF controls the DF bit in PLL_CTL      0 = CLKIN		*/
+/*                                                1 = CLKIN / 2		*/
+#define CONFIG_CLKIN_HALF		0
+/* PLL_BYPASS controls the BYPASS bit in PLL_CTL  0 = do not bypass	*/
+/*                                                1 = bypass PLL	*/
+#define CONFIG_PLL_BYPASS		0
+/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL		*/
+/* Values can range from 0-63 (where 0 means 64)			*/
+#define CONFIG_VCO_MULT			24
+/* CCLK_DIV controls the core clock divider				*/
+/* Values can be 1, 2, 4, or 8 ONLY					*/
+#define CONFIG_CCLK_DIV			1
+/* SCLK_DIV controls the system clock divider				*/
+/* Values can range from 1-15						*/
+#define CONFIG_SCLK_DIV			5
+
+
+/*
+ * Memory Settings
+ */
+#define CONFIG_MEM_ADD_WDTH	9
+#define CONFIG_MEM_SIZE		64
+
+#define CONFIG_EBIU_SDRRC_VAL	0x377
+#define CONFIG_EBIU_SDGCTL_VAL	0x91998d
+#define CONFIG_EBIU_SDBCTL_VAL	0x15
+
+#define CONFIG_EBIU_AMGCTL_VAL	0x3F
+#define CONFIG_EBIU_AMBCTL0_VAL	0x7BB07BB0
+#define CONFIG_EBIU_AMBCTL1_VAL	0xFFC27BB0
+
+#define CONFIG_SYS_MONITOR_LEN	(256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN	(128 * 1024)
+
+
+/*
+ * Flash Settings
+ */
+#define CONFIG_SYS_FLASH_CFI		/* The flash is CFI compatible */
+#define CONFIG_FLASH_CFI_DRIVER	/* Use common CFI driver */
+#define CONFIG_SYS_FLASH_CFI_AMD_RESET
+#define CONFIG_SYS_FLASH_BASE		0x20000000
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	135	/* max number of sectors on one chip */
+/* The BF561-EZKIT uses a top boot flash */
+#define CONFIG_ENV_IS_IN_FLASH	1
+#define CONFIG_ENV_ADDR		0x20004000
+#define CONFIG_ENV_OFFSET		(CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x10000	/* Total Size of Environment Sector */
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
+#define ENV_IS_EMBEDDED
+#else
+#define ENV_IS_EMBEDDED_CUSTOM
+#endif
+
+
+/*
+ * I2C Settings
+ */
+#define CONFIG_SOFT_I2C		1
+#define PF_SCL			0x1/*PF0*/
+#define PF_SDA			0x2/*PF1*/
+
+#ifdef CONFIG_SOFT_I2C
+#define I2C_INIT       do { *pFIO0_DIR |= PF_SCL; SSYNC(); } while (0)
+#define I2C_ACTIVE     do { *pFIO0_DIR |= PF_SDA; *pFIO0_INEN &= ~PF_SDA; SSYNC(); } while (0)
+#define I2C_TRISTATE   do { *pFIO0_DIR &= ~PF_SDA; *pFIO0_INEN |= PF_SDA; SSYNC(); } while (0)
+#define I2C_READ       ((*pFIO0_FLAG_D & PF_SDA) != 0)
+#define I2C_SDA(bit) \
+	do { \
+		if (bit) \
+			*pFIO0_FLAG_S = PF_SDA; \
+		else \
+			*pFIO0_FLAG_C = PF_SDA; \
+		SSYNC(); \
+	} while (0)
+#define I2C_SCL(bit) \
+	do { \
+		if (bit) \
+			*pFIO0_FLAG_S = PF_SCL; \
+		else \
+			*pFIO0_FLAG_C = PF_SCL; \
+		SSYNC(); \
+	} while (0)
+#define I2C_DELAY		udelay(5)	/* 1/4 I2C clock duration */
+
+#define CONFIG_SYS_I2C_SPEED	50000
+#define CONFIG_SYS_I2C_SLAVE	0
+#endif
+
+
+/*
+ * Misc Settings
+ */
+#define CONFIG_UART_CONSOLE	0
+
+
+/*
+ * Pull in common ADI header for remaining command/environment setup
+ */
+#include <configs/bfin_adi_common.h>
+
+#include <asm/blackfin-config-post.h>
+
+#endif				/* __CONFIG_IBF_DSP561__H__ */