powerpc: ppc4xx: remove csb272, csb472 support

These have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tolunay Orkun <torkun@nextio.com>

1 files changed, 0 insertions, 282 deletions

diff --git a/include/configs/csb272.h b/include/configs/csb272.h
deleted file mode 100644
index 71cb5dff36..0000000000
--- a/include/configs/csb272.h
+++ /dev/null
@@ -1,282 +0,0 @@
-/*
- * (C) Copyright 2004
- * Tolunay Orkun, Nextio Inc., torkun@nextio.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405GP		1	/* This is a PPC405GP CPU	*/
-#define CONFIG_CSB272		1	/* on a Cogent CSB272 board     */
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f()    */
-#define CONFIG_LAST_STAGE_INIT	1	/* Call last_stage_init()	*/
-#define CONFIG_SYS_CLK_FREQ     33000000 /* external frequency to pll   */
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000
-
-/*
- * OS Bootstrap configuration
- *
- */
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY	3	/* autoboot after X seconds	*/
-#endif
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check keypress when bootdelay = 0 */
-
-#if 1
-#undef  CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
-	"setenv bootargs console=ttyS0,38400 debug " \
-	"root=/dev/ram rw ramdisk_size=4096 " \
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
-	"bootm fe000000 fe100000"
-#endif
-
-#if 0
-#undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
-	"bootp; " \
-	"setenv bootargs console=ttyS0,38400 debug " \
-	"root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
-	"bootm"
-#endif
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_DNS2
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-
-
-/*
- * Serial download configuration
- *
- */
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-/*
- * KGDB Configuration
- *
- */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
-/*
- * Miscellaneous configurable options
- *
- */
-#undef	CONFIG_SYS_HUSH_PARSER			/* use "hush" command parser */
-
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size */
-#else
-#define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_info (bd_t) */
-#define CONFIG_SYS_LOAD_ADDR		0x100000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
-
-/*
- * watchdog configuration
- *
- */
-#undef  CONFIG_WATCHDOG			/* watchdog disabled */
-
-/*
- * UART configuration
- *
- */
-#define CONFIG_CONS_INDEX		1	/* Use UART0		*/
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
-
-#define CONFIG_SYS_EXT_SERIAL_CLOCK	3868400	/* use external serial clock */
-#undef  CONFIG_SYS_BASE_BAUD
-#define CONFIG_BAUDRATE		38400	/* Default baud rate */
-#define CONFIG_SYS_BAUDRATE_TABLE      \
-    { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * I2C configuration
- *
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F	/* I2C slave address */
-
-/*
- * MII PHY configuration
- *
- */
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_PHY_ADDR		0	/* PHY address			*/
-#define CONFIG_PHY_CMD_DELAY	40	/* PHY COMMAND delay		*/
-					/* 32usec min. for LXT971A	*/
-#define CONFIG_PHY_RESET_DELAY	300	/* PHY RESET recovery delay	*/
-
-/*
- * RTC configuration
- *
- * Note that DS1307 RTC is limited to 100Khz I2C bus.
- *
- */
-#define CONFIG_RTC_DS1307		/* Use Dallas 1307 RTC		*/
-
-/*
- * PCI stuff
- *
- */
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define PCI_HOST_ADAPTER	0	/* configure ar pci adapter     */
-#define PCI_HOST_FORCE		1	/* configure as pci host        */
-#define PCI_HOST_AUTO		2	/* detected via arbiter enable  */
-
-#define CONFIG_PCI_HOST	PCI_HOST_FORCE  /* select pci host function     */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
-#undef  CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
-#define CONFIG_PCI_BOOTDELAY    0       /* enable pci bootdelay variable*/
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000  /* PCI Vendor ID: to-do!!!      */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000  /* PCI Device ID: to-do!!!      */
-#define CONFIG_SYS_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CONFIG_SYS_PCI_PTM1MS  0x80000001      /* 2GB, enable hard-wired to 1  */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CONFIG_SYS_PCI_PTM2LA  0x00000000      /* disabled                     */
-#define CONFIG_SYS_PCI_PTM2MS  0x00000000      /* disabled                     */
-#define CONFIG_SYS_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
-
-/*
- * IDE stuff
- *
- */
-#undef  CONFIG_IDE_PCMCIA               /* no pcmcia interface required */
-#undef  CONFIG_IDE_LED                  /* no led for ide supported     */
-#undef  CONFIG_IDE_RESET                /* no reset for ide supported   */
-
-/*
- * Environment configuration
- *
- */
-#define CONFIG_ENV_IS_IN_FLASH	1	/* environment is in FLASH	*/
-#undef CONFIG_ENV_IS_IN_NVRAM
-#undef CONFIG_ENV_IS_IN_EEPROM
-
-/*
- * General Memory organization
- *
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0xFE000000
-#define CONFIG_SYS_FLASH_SIZE		0x02000000
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 KB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN		(128 * 1024) /* Reserve 128 KB for malloc() */
-
-#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_RAMSTART
-#endif
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-#define CONFIG_ENV_IN_OWN_SECTOR	1	   /* Give Environment own sector */
-#define CONFIG_ENV_ADDR		0xFFF00000 /* Address of Environment Sector */
-#define	CONFIG_ENV_SIZE		0x00001000 /* Size of Environment */
-#define CONFIG_ENV_SECT_SIZE	0x00040000 /* Size of Environment Sector */
-#endif
-
-/*
- * FLASH Device configuration
- *
- */
-#define CONFIG_SYS_FLASH_CFI		1	/* flash is CFI conformant	*/
-#define CONFIG_FLASH_CFI_DRIVER	1	/* use common cfi driver	*/
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster) */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max # of memory banks	*/
-#define CONFIG_SYS_FLASH_INCREMENT	0	/* there is only one bank	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	128	/* max # of sectors on one chip	*/
-#define CONFIG_SYS_FLASH_PROTECTION	1	/* hardware flash protection	*/
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
-
-/*
- * On Chip Memory location/size
- *
- */
-#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
-
-/*
- * Global info and initial stack
- *
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of on-chip SRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*
- * Miscellaneous board specific definitions
- *
- */
-#define CONFIG_SYS_I2C_PLL_ADDR	0x58	/* I2C address of AMIS FS6377-01 PLL */
-#define CONFIG_I2CFAST		1	/* enable "i2cfast" env. setting     */
-
-#endif	/* __CONFIG_H */