Blackfin: blackvme: new board port

The board includes:
 * ADSP-BF561 rev. 0.5
 * 32-bit SDRAM (2 * MT48LC16M16A2TG or MT48LC32M16A2TG)
 * Gigabit Ether AX88180 (ASIX) + 88E1111 rev. B2 (Marvell)
 * SPI  boot flash on PF2 (M25P64 8MB, or M25P128 16 MB)
 * FPGA boot flash on PF3 (M25P64 8MB, or M25P128 16 MB)
 * Spartan6-LX150 (memory-mapped; both PPIs also connected)
 * See http://www.skutek.com/

Signed-off-by: Wojtek Skulski <skulski@pas.rochester.edu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

1 files changed, 246 insertions, 0 deletions

diff --git a/include/configs/blackvme.h b/include/configs/blackvme.h
new file mode 100644
index 0000000000..8b2bdc715d
--- /dev/null
+++ b/include/configs/blackvme.h
@@ -0,0 +1,246 @@
+/* U-boot for BlackVME. (C) Wojtek Skulski 2010.
+ * The board includes ADSP-BF561 rev. 0.5,
+ * 32-bit SDRAM (2 * MT48LC16M16A2TG or MT48LC32M16A2TG),
+ * Gigabit Ether AX88180 (ASIX) + 88E1111 rev. B2 (Marvell),
+ * SPI  boot flash on PF2 (M25P64 8MB, or M25P128 16 MB),
+ * FPGA boot flash on PF3 (M25P64 8MB, or M25P128 16 MB),
+ * Spartan6-LX150 (memory-mapped; both PPIs also connected).
+ * See http://www.skutek.com
+ */
+
+#ifndef __CONFIG_BLACKVME_H__
+#define __CONFIG_BLACKVME_H__
+
+#include <asm/config-pre.h>
+
+/* Debugging: Set these options if you're having problems
+ * #define CONFIG_DEBUG_EARLY_SERIAL
+ * #define DEBUG
+ * #define CONFIG_DEBUG_DUMP
+ * #define CONFIG_DEBUG_DUMP_SYMS
+ * CONFIG_PANIC_HANG means that the board will not auto-reboot
+ */
+#define CONFIG_PANIC_HANG 0
+
+/* CPU Options */
+#define CONFIG_BFIN_BOOT_MODE	BFIN_BOOT_SPI_MASTER
+
+/*
+ *		CLOCK SETTINGS CAVEAT
+ * You CANNOT just change the clock settings, esp. the SCLK.
+ * The SDRAM timing, SPI baud, and the serial UART baud
+ * use SCLK frequency to set their own frequencies. Therefore,
+ * if you change the SCLK_DIV, you may also have to adjust
+ * SDRAM refresh and other timings.
+ * --------------------------------------------------------------
+ *	CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ *		25 *  8 / 1 = 200 MHz
+ *		25 * 16 / 1 = 400 MHz
+ *		25 * 24 / 1 = 600 MHz
+ *	SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
+ *		25 *  8 / 2 = 100 MHz
+ *		25 * 24 / 6 = 100 MHz
+ *		25 * 24 / 5 = 120 MHz
+ *		25 * 16 / 3 = 133 MHz
+ * 25 MHz because the oscillator also feeds the ether chip.
+ * CONFIG_CLKIN_HZ is 25 MHz written in Hz
+ * CLKIN_HALF controls the DF bit in PLL_CTL
+ *	0 = CLKIN	1 = CLKIN / 2
+ * PLL_BYPASS controls the BYPASS bit in PLL_CTL
+ *	0 = do not bypass	1 = bypass PLL
+ * VCO_MULT = MSEL (multiplier) in PLL_CTL
+ * Values can range from 0-63 (where 0 means 64)
+ * CCLK_DIV = core clock divider (1, 2, 4, or 8 ONLY)
+ * SCLK_DIV = system clock divider, 1 to 15
+ */
+#define CONFIG_CLKIN_HZ		25000000
+#define CONFIG_CLKIN_HALF	0
+#define CONFIG_PLL_BYPASS	0
+#define CONFIG_VCO_MULT		8
+#define CONFIG_CCLK_DIV		1
+#define CONFIG_SCLK_DIV		2
+
+/*
+ * Ether chip in async memory space AMS3, same as BF561-EZ-KIT.
+ * Used in 32-bit mode. 16-bit mode not supported.
+ * http://docs.blackfin.uclinux.org/doku.php?id=hw:cards:ax88180
+ */
+/*
+ * Network settings using a dedicated 2nd ether card in PC
+ * Windows will automatically acquire IP of that card
+ * Then use the dedicated card IP + 1 for the board
+ * http://docs.blackfin.uclinux.org/doku.php?id=setting_up_the_network
+ */
+#define CONFIG_NET_MULTI
+
+#define CONFIG_DRIVER_AX88180	1
+#define AX88180_BASE		0x2c000000
+#define CONFIG_CMD_MII		/* enable probing PHY */
+
+#ifdef CONFIG_NET_MULTI		/* also used as the network enabler */
+# define CONFIG_HOSTNAME	blackvme	/* Bfin board  */
+# define CONFIG_IPADDR		169.254.144.145	/* Bfin board  */
+# define CONFIG_GATEWAYIP	169.254.144.144	/* dedic card  */
+# define CONFIG_SERVERIP	169.254.144.144	/* tftp server */
+# define CONFIG_NETMASK		255.255.255.0
+# define CONFIG_ROOTPATH	/export/uClinux-dist/romfs	/*NFS*/
+# define CFG_AUTOLOAD		"no"
+# define CONFIG_CMD_DHCP
+# define CONFIG_CMD_PING
+# define CONFIG_ENV_OVERWRITE	1	/* enable changing MAC at runtime */
+/* Comment out hardcoded MAC to enable MAC storage in EEPROM */
+/* # define CONFIG_ETHADDR	ff:ee:dd:cc:bb:aa */
+#endif
+
+/*
+ * SDRAM settings & memory map
+ */
+
+#define CONFIG_MEM_SIZE		64	/* 128, 64, 32, 16 */
+#define CONFIG_MEM_ADD_WDTH	 9	/* 8, 9, 10, 11    */
+/*
+ * SDRAM reference page
+ * http://docs.blackfin.uclinux.org/doku.php?id=bfin:sdram
+ * NOTE: BlackVME populates only SDRAM bank 0
+ */
+/* CONFIG_EBIU_SDBCTL_VAL bank ctrl may be needed in future */
+#define CONFIG_EBIU_SDGCTL_VAL  0x91114d  /* global control */
+#define CONFIG_EBIU_SDRRC_VAL   0x306     /* refresh rate */
+
+/* Async memory global settings. (ASRAM, not SDRAM)
+ * HRM page 16-10. Global ASRAM control = 0x3F. Six lower bits = 1
+ * CLKOUT enabled, all async banks enabled, core has priority
+ * bank 0&1 16 bit (FPGA)
+ * bank 2&3 32 bit (ether and USB chips)
+ */
+#define CONFIG_EBIU_AMGCTL_VAL  0x3F   /* ASRAM setup */
+
+/* Async mem timing: BF561 HRM page 16-12 and 16-15.
+ * Default values 0xFFC2 FFC2 are the slowest supported.
+ * Example settings of CONFIG_EBIU_AMBCTL1_VAL
+ * 1. EZ-KIT settings: 0xFFC2 7BB0
+ * 2. Bank 3 good timing for AX88180 @ 125MHz = 0x8850 xxxx
+ *    See the following page:
+ *    http://docs.blackfin.uclinux.org/doku.php?id=hw:cards:ax88180
+ * 3. Bank 3 timing for AX88180 @ SCLK = 100 MHz:
+ * AX88180  WEN = 5 clocks  REN 6 clocks @ SCLK = 100 MHz
+ * One extra clock needed because AX88180 is asynchronous to CPU.
+ */
+                           /* bank 1   0 */
+#define CONFIG_EBIU_AMBCTL0_VAL 0xFFC2FFC2
+                           /* bank 3   2 */
+#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC2FFC2
+
+/* memory layout */
+
+#define CONFIG_SYS_MONITOR_LEN	(256 << 10)
+#define CONFIG_SYS_MALLOC_LEN	(384 << 10)
+
+/*
+ * Serial SPI Flash
+ * For the M25P64 SCK should be kept < 15 MHz
+ */
+#define CONFIG_BFIN_SPI
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_OFFSET	0x40000
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x40000
+
+#define CONFIG_ENV_SPI_MAX_HZ	15000000
+#define CONFIG_SF_DEFAULT_SPEED	15000000
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+
+/*
+ * Interactive command settings
+ */
+
+#define CONFIG_SYS_LONGHELP	1
+#define CONFIG_CMDLINE_EDITING	1
+#define CONFIG_AUTO_COMPLETE	1
+
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BOOTLDR
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_CPLBINFO
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_ELF
+
+/*
+ * Default: boot from SPI flash.
+ * "sfboot" is a composite command defined in extra settings
+ */
+#define CONFIG_BOOTDELAY	5
+#define CONFIG_BOOTCOMMAND	"run sfboot"
+
+/*
+ * Console settings
+ */
+#define CONFIG_BAUDRATE		57600
+#define CONFIG_LOADS_ECHO	1
+#define CONFIG_UART_CONSOLE	0
+
+/*
+ * U-Boot environment variables. Use "printenv" to examine.
+ * http://docs.blackfin.uclinux.org/doku.php?id=bootloaders:u-boot:env
+ */
+#define CONFIG_BOOTARGS \
+	"root=/dev/mtdblock0 rw " \
+	"clkin_hz=" MK_STR(CONFIG_CLKIN_HZ) " " \
+	"earlyprintk=serial,uart0," \
+	MK_STR(CONFIG_BAUDRATE) " " \
+	"console=ttyBF0," MK_STR(CONFIG_BAUDRATE) " "
+
+/* Convenience env variables & commands.
+ * Reserve kernstart = 0x20000  = 128 kB for U-Boot.
+ * Reserve kernarea  = 0x500000 = 5 MB   for kernel (reasonable size).
+ * U-Boot image is saved at flash offset=0.
+ * Kernel image is saved at flash offset=$kernstart.
+ * Instructions. Ksave takes about a minute to complete.
+ *	1. Update U-Boot: run uget; run usave
+ *	2. Update kernel: run kget; run ksave
+ * After updating U-Boot also update the kernel per above instructions
+ * to make the saved environment consistent with the flash.
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"kernstart=0x20000\0" \
+	"kernarea=0x500000\0" \
+	"uget=tftp u-boot.ldr\0" \
+	"kget=tftp uImage\0" \
+	"usave=sf probe 2; " \
+		"sf erase 0 $(kernstart); " \
+		"sf write $(fileaddr) 0 $(filesize)\0" \
+	"ksave=sf probe 2; " \
+		"saveenv; " \
+		"echo Now patiently wait for the prompt...; " \
+		"sf erase $(kernstart) $(kernarea); " \
+		"sf write $(fileaddr) $(kernstart) $(filesize)\0" \
+	"sfboot=sf probe 2; " \
+		"sf read $(loadaddr) $(kernstart) $(filesize); " \
+		"run addip; bootm\0" \
+	"addip=setenv bootargs $(bootargs) " \
+	"ip=$(ipaddr):$(serverip):$(gatewayip):" \
+		"$(netmask):$(hostname):eth0:off\0"
+
+/*
+ * Soft I2C settings (BF561 does not have hard I2C)
+ * PF12,13 on SPI connector 0.
+ */
+#ifdef CONFIG_SOFT_I2C
+# define CONFIG_CMD_I2C
+# define CONFIG_SOFT_I2C_GPIO_SCL	GPIO_PF12
+# define CONFIG_SOFT_I2C_GPIO_SDA	GPIO_PF13
+# define CONFIG_SYS_I2C_SPEED		50000
+# define CONFIG_SYS_I2C_SLAVE		0xFE
+#endif
+
+/*
+ * No Parallel Flash on this board
+ */
+#define CONFIG_SYS_NO_FLASH
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_JFFS2
+#undef CONFIG_CMD_FLASH
+
+#endif