powerpc/t1024rdb: Add T1024 RDB board support

T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.

T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
  - Two 10M/100M/1G RGMII ports on-board
  - one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two  Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
	   Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>

1 files changed, 896 insertions, 0 deletions

diff --git a/include/configs/T102xRDB.h b/include/configs/T102xRDB.h
new file mode 100644
index 0000000000..6f1fcd62ca
--- /dev/null
+++ b/include/configs/T102xRDB.h
@@ -0,0 +1,896 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+/*
+ * T1024/T1023 RDB board configuration file
+ */
+
+#ifndef __T1024RDB_H
+#define __T1024RDB_H
+
+/* High Level Configuration Options */
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_BOOKE
+#define CONFIG_E500			/* BOOKE e500 family */
+#define CONFIG_E500MC			/* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
+#define CONFIG_MP			/* support multiple processors */
+#define CONFIG_PHYS_64BIT
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP		1
+#define CONFIG_SYS_NUM_ADDR_MAP	64	/* number of TLB1 entries */
+#endif
+
+#define CONFIG_SYS_FSL_CPC		/* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC		CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_IFC			/* Enable IFC Support */
+
+#define CONFIG_FSL_LAW			/* Use common FSL init code */
+#define CONFIG_ENV_OVERWRITE
+
+/* support deep sleep */
+#define CONFIG_DEEP_SLEEP
+#define CONFIG_SILENT_CONSOLE
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xrdb/t1024_pbi.cfg
+#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_rcw.cfg
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_FSL_LAW			/* Use common FSL init code */
+#define CONFIG_SYS_TEXT_BASE		0x00201000
+#define CONFIG_SPL_TEXT_BASE		0xFFFD8000
+#define CONFIG_SPL_PAD_TO		0x40000
+#define CONFIG_SPL_MAX_SIZE		0x28000
+#define RESET_VECTOR_OFFSET		0x27FFC
+#define BOOT_PAGE_OFFSET		0x27000
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_SKIP_RELOCATE
+#define CONFIG_SPL_COMMON_INIT_DDR
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#ifdef CONFIG_NAND
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST	0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_START	0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	(256 << 10)
+#define CONFIG_SYS_LDSCRIPT	"arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
+#define CONFIG_SPL_NAND_BOOT
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_RESET_VECTOR_ADDRESS		0x200FFC
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_MINIMAL
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE	(768 << 10)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST		(0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_START	(0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS	(256 << 10)
+#define CONFIG_SYS_LDSCRIPT		"arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SPL_SPI_BOOT
+#endif
+
+#ifdef CONFIG_SDCARD
+#define CONFIG_RESET_VECTOR_ADDRESS	0x200FFC
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_MMC_MINIMAL
+#define CONFIG_SYS_MMC_U_BOOT_SIZE	(768 << 10)
+#define CONFIG_SYS_MMC_U_BOOT_DST	(0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_START	(0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_OFFS	(260 << 10)
+#define CONFIG_SYS_LDSCRIPT		"arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SPL_MMC_BOOT
+#endif
+
+#endif /* CONFIG_RAMBOOT_PBL */
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE	0xeff40000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
+#endif
+
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+/* PCIe Boot - Master */
+#define CONFIG_SRIO_PCIE_BOOT_MASTER
+/*
+ * for slave u-boot IMAGE instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
+#else
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xef200000
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0xfff00000
+#endif
+/*
+ * for slave UCODE and ENV instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS	 0x3ffe00000ull
+#else
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xef100000
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS  0xffe00000
+#endif
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE	0x40000 /* 256K */
+/* slave core release by master*/
+#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET	0xe00e4
+#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK	0x00000001 /* release core 0 */
+
+/* PCIe Boot - Slave */
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
+		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
+/* Set 1M boot space for PCIe boot */
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS	\
+		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS		0
+#define CONFIG_ENV_SPI_CS		0
+#define CONFIG_ENV_SPI_MAX_HZ		10000000
+#define CONFIG_ENV_SPI_MODE		0
+#define CONFIG_ENV_SIZE			0x2000		/* 8KB */
+#define CONFIG_ENV_OFFSET		0x100000	/* 1MB */
+#define CONFIG_ENV_SECT_SIZE		0x10000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_ENV_SIZE			0x2000
+#define CONFIG_ENV_OFFSET		(512 * 0x800)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE			0x2000
+#define CONFIG_ENV_OFFSET		(2 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+#define CONFIG_ENV_IS_IN_REMOTE
+#define CONFIG_ENV_ADDR		0xffe20000
+#define CONFIG_ENV_SIZE		0x2000
+#elif defined(CONFIG_ENV_IS_NOWHERE)
+#define CONFIG_ENV_SIZE		0x2000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+#endif
+
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ	100000000
+#define CONFIG_DDR_CLK_FREQ	66660000
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BACKSIDE_L2_CACHE
+#define CONFIG_SYS_INIT_L2CSR0		L2CSR0_L2E
+#define CONFIG_BTB			/* toggle branch predition */
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
+#endif
+
+#define CONFIG_SYS_MEMTEST_START	0x00200000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0x00400000
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
+/*
+ *  Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR		0xFFFC0000
+#define CONFIG_SYS_L3_SIZE		(256 << 10)
+#define CONFIG_SPL_GD_ADDR		(CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_ENV_ADDR			(CONFIG_SPL_GD_ADDR + 4 * 1024)
+#endif
+#define CONFIG_SPL_RELOC_MALLOC_ADDR	(CONFIG_SPL_GD_ADDR + 12 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE	(30 << 10)
+#define CONFIG_SPL_RELOC_STACK		(CONFIG_SPL_GD_ADDR + 64 * 1024)
+#define CONFIG_SPL_RELOC_STACK_SIZE	(22 << 10)
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_DCSRBAR		0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
+#endif
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM	0
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_FSL_DDR3
+
+#define CONFIG_SYS_SPD_BUS_NUM	0
+#define SPD_EEPROM_ADDRESS	0x51
+
+#define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_FLASH_BASE	0xe8000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+#else
+#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
+#endif
+
+#define CONFIG_SYS_NOR0_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+				CSPR_PORT_SIZE_16 | \
+				CSPR_MSEL_NOR | \
+				CSPR_V)
+#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
+
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80
+#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
+				FTIM0_NOR_TEADC(0x5) | \
+				FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
+				FTIM1_NOR_TRAD_NOR(0x1A) |\
+				FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
+				FTIM2_NOR_TCH(0x4) | \
+				FTIM2_NOR_TWPH(0x0E) | \
+				FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3	0x0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS}
+
+/* CPLD on IFC */
+#define CONFIG_SYS_CPLD_BASE		0xffdf0000
+#define CONFIG_SYS_CPLD_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_CPLD_BASE)
+#define CONFIG_SYS_CSPR2_EXT		(0xf)
+#define CONFIG_SYS_CSPR2		(CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
+						| CSPR_PORT_SIZE_8 \
+						| CSPR_MSEL_GPCM \
+						| CSPR_V)
+#define CONFIG_SYS_AMASK2		IFC_AMASK(64*1024)
+#define CONFIG_SYS_CSOR2		0x0
+
+/* CPLD Timing parameters for IFC CS2 */
+#define CONFIG_SYS_CS2_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
+						FTIM0_GPCM_TEADC(0x0e) | \
+						FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS2_FTIM1		(FTIM1_GPCM_TACO(0x0e) | \
+						FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_CS2_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
+						FTIM2_GPCM_TCH(0x8) | \
+						FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS2_FTIM3		0x0
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE		0xff800000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NAND_BASE)
+#else
+#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
+#endif
+#define CONFIG_SYS_NAND_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
+				| CSPR_V)
+#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
+
+#define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
+				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
+				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
+				| CSOR_NAND_RAL_3	/* RAL = 3Byes */ \
+				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
+				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
+				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
+					FTIM0_NAND_TWP(0x18)   | \
+					FTIM0_NAND_TWCHT(0x07) | \
+					FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
+					FTIM1_NAND_TWBE(0x39)  | \
+					FTIM1_NAND_TRR(0x0e)   | \
+					FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
+					FTIM2_NAND_TREH(0x0a) | \
+					FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3		0x0
+
+#define CONFIG_SYS_NAND_DDR_LAW		11
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(512 * 1024)
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NAND_FTIM3
+#endif
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SPL_TEXT_BASE
+#else
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
+#endif
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xfdd00000	/* Initial L1 address */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe0ec000
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#else
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS	0xfe0ec000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+#endif
+#define CONFIG_SYS_INIT_RAM_SIZE		0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+					GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(10 * 1024 * 1024)
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_CCSRBAR+0x11D600)
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV	/* determine from environment */
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* Video */
+#undef CONFIG_FSL_DIU_FB	/* RDB doesn't support DIU */
+#ifdef CONFIG_FSL_DIU_FB
+#define CONFIG_SYS_DIU_ADDR	(CONFIG_SYS_CCSRBAR + 0x180000)
+#define CONFIG_VIDEO
+#define CONFIG_CMD_BMP
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+/*
+ * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so
+ * disable empty flash sector detection, which is I/O-intensive.
+ */
+#undef CONFIG_SYS_FLASH_EMPTY_INFO
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL		/* Use FSL common I2C driver */
+#define CONFIG_SYS_FSL_I2C_SPEED	50000	/* I2C speed in Hz */
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C2_SPEED	50000	/* I2C speed in Hz */
+#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x118000
+#define CONFIG_SYS_FSL_I2C2_OFFSET	0x118100
+
+#define I2C_MUX_PCA_ADDR		0x77
+#define I2C_MUX_PCA_ADDR_PRI		0x77 /* Primary Mux*/
+
+
+/* I2C bus multiplexer */
+#define I2C_MUX_CH_DEFAULT	0x8
+
+/*
+ * RTC configuration
+ */
+#define RTC
+#define CONFIG_RTC_DS1337	1
+#define CONFIG_SYS_I2C_RTC_ADDR	0x68
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH_BAR
+#define CONFIG_SF_DEFAULT_SPEED	10000000
+#define CONFIG_SF_DEFAULT_MODE	0
+
+/*
+ * General PCIe
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+#define CONFIG_PCI		/* Enable PCI/PCIE */
+#define CONFIG_PCIE1		/* PCIE controler 1 */
+#define CONFIG_PCIE2		/* PCIE controler 2 */
+#define CONFIG_PCIE3		/* PCIE controler 3 */
+#ifdef CONFIG_PPC_T1040
+#define CONFIG_PCIE4		/* PCIE controler 4 */
+#endif
+#define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
+#define CONFIG_PCI_INDIRECT_BRIDGE
+
+#ifdef CONFIG_PCI
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#ifdef CONFIG_PCIE1
+#define	CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define	CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
+#define	CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0x80000000
+#endif
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull
+#else
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xf8000000
+#endif
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
+#endif
+
+/* controller 2, Slot 2, tgtid 2, Base address 201000 */
+#ifdef CONFIG_PCIE2
+#define CONFIG_SYS_PCIE2_MEM_VIRT	0x90000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xc10000000ull
+#else
+#define CONFIG_SYS_PCIE2_MEM_BUS	0x90000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0x90000000
+#endif
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE2_IO_VIRT	0xf8010000
+#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xff8010000ull
+#else
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xf8010000
+#endif
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
+#endif
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#ifdef CONFIG_PCIE3
+#define CONFIG_SYS_PCIE3_MEM_VIRT	0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc20000000ull
+#else
+#define CONFIG_SYS_PCIE3_MEM_BUS	0xa0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS	0xa0000000
+#endif
+#define CONFIG_SYS_PCIE3_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE3_IO_VIRT	0xf8020000
+#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_IO_PHYS	0xff8020000ull
+#else
+#define CONFIG_SYS_PCIE3_IO_PHYS	0xf8020000
+#endif
+#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
+#endif
+
+/* controller 4, Base address 203000, to be removed */
+#ifdef CONFIG_PCIE4
+#define CONFIG_SYS_PCIE4_MEM_VIRT       0xb0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE4_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE4_MEM_PHYS       0xc30000000ull
+#else
+#define CONFIG_SYS_PCIE4_MEM_BUS	0xb0000000
+#define CONFIG_SYS_PCIE4_MEM_PHYS	0xb0000000
+#endif
+#define CONFIG_SYS_PCIE4_MEM_SIZE       0x10000000      /* 256M */
+#define CONFIG_SYS_PCIE4_IO_VIRT	0xf8030000
+#define CONFIG_SYS_PCIE4_IO_BUS		0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE4_IO_PHYS	0xff8030000ull
+#else
+#define CONFIG_SYS_PCIE4_IO_PHYS	0xf8030000
+#endif
+#define CONFIG_SYS_PCIE4_IO_SIZE	0x00010000      /* 64k */
+#endif
+
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+#define CONFIG_E1000
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif	/* CONFIG_PCI */
+
+/*
+ * USB
+ */
+#define CONFIG_HAS_FSL_DR_USB
+
+#ifdef CONFIG_HAS_FSL_DR_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#endif
+
+/*
+ * SDHC
+ */
+#define CONFIG_MMC
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Qman/Bman */
+#ifndef CONFIG_NOBQFMAN
+#define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS	25
+#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
+#else
+#define CONFIG_SYS_BMAN_MEM_PHYS	CONFIG_SYS_BMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_BMAN_MEM_SIZE	0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS	25
+#define CONFIG_SYS_QMAN_MEM_BASE	0xf6000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_QMAN_MEM_PHYS	0xff6000000ull
+#else
+#define CONFIG_SYS_QMAN_MEM_PHYS	CONFIG_SYS_QMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_QMAN_MEM_SIZE	0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+
+#define CONFIG_QE
+#define CONFIG_U_QE
+/* Default address of microcode for the Linux FMan driver */
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_QE_FW_ADDR	0x130000
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 1MB (2048 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080(0x820).
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_FMAN_FW_ADDR		(512 * 0x820)
+#define CONFIG_SYS_QE_FW_ADDR		(512 * 0x920)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_FMAN_FW_ADDR		(3 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_QE_FW_ADDR		(4 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+/*
+ * Slave has no ucode locally, it can fetch this from remote. When implementing
+ * in two corenet boards, slave's ucode could be stored in master's memory
+ * space, the address can be mapped from slave TLB->slave LAW->
+ * slave SRIO or PCIE outbound window->master inbound window->
+ * master LAW->the ucode address in master's memory space.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+#define CONFIG_SYS_FMAN_FW_ADDR		0xFFE00000
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
+#define CONFIG_SYS_QE_FW_ADDR		0xEFE00000
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
+#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif /* CONFIG_NOBQFMAN */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_REALTEK
+#define RGMII_PHY1_ADDR		0x2
+#define RGMII_PHY2_ADDR		0x6
+#define FM1_10GEC1_PHY_ADDR	0x1
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_MII		/* MII PHY management */
+#define CONFIG_ETHPRIME		"FM1@DTSEC4"
+#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * Dynamic MTD Partition support with mtdparts
+ */
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_FLASH_CFI_MTD
+#define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
+			"spi0=spife110000.1"
+#define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
+			"128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \
+			"5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:" \
+			"1m(uboot),5m(kernel),128k(dtb),-(user)"
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_LOADS_ECHO		/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_BDI
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
+#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE  CONFIG_SYS_CBSIZE  /* Boot Argument Buffer Size */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH		"/opt/nfsroot"
+#define CONFIG_BOOTFILE		"uImage"
+#define CONFIG_UBOOTPATH	"u-boot.bin" /* U-Boot image on TFTP server */
+#define CONFIG_LOADADDR		1000000 /* default location for tftp, bootm */
+#define CONFIG_BOOTDELAY	10	/* -1 disables auto-boot */
+#define CONFIG_BAUDRATE		115200
+#define __USB_PHY_TYPE		utmi
+
+#ifdef CONFIG_PPC_T1024
+#define CONFIG_BOARDNAME "t1024rdb"
+#else
+#define CONFIG_BOARDNAME "t1023rdb"
+#endif
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"hwconfig=fsl_ddr:ctlr_intlv=cacheline,"		\
+	"bank_intlv=cs0_cs1\0"					\
+	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"  \
+	"ramdiskfile=" __stringify(CONFIG_BOARDNAME) "/ramdisk.uboot\0" \
+	"fdtfile=" __stringify(CONFIG_BOARDNAME) "/"		\
+	__stringify(CONFIG_BOARDNAME) ".dtb\0"			\
+	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
+	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
+	"bootargs=root=/dev/ram rw console=ttyS0,115200\0" \
+	"netdev=eth0\0"						\
+	"tftpflash=tftpboot $loadaddr $uboot && "		\
+	"protect off $ubootaddr +$filesize && "			\
+	"erase $ubootaddr +$filesize && "			\
+	"cp.b $loadaddr $ubootaddr $filesize && "		\
+	"protect on $ubootaddr +$filesize && "			\
+	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
+	"consoledev=ttyS0\0"					\
+	"ramdiskaddr=2000000\0"					\
+	"fdtaddr=c00000\0"					\
+	"bdev=sda3\0"
+
+#define CONFIG_LINUX					\
+	"setenv bootargs root=/dev/ram rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"setenv ramdiskaddr 0x02000000;"		\
+	"setenv fdtaddr 0x00c00000;"			\
+	"setenv loadaddr 0x1000000;"			\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+
+#define CONFIG_NFSBOOTCOMMAND			\
+	"setenv bootargs root=/dev/nfs rw "	\
+	"nfsroot=$serverip:$rootpath "		\
+	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"		\
+	"tftp $fdtaddr $fdtfile;"		\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND	CONFIG_LINUX
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#endif
+
+#endif	/* __T1024RDB_H */