Merge branch 'master' of git://git.denx.de/u-boot-arm

1 files changed, 0 insertions, 190 deletions

diff --git a/include/configs/EXBITGEN.h b/include/configs/EXBITGEN.h
deleted file mode 100644
index 208b599f6d..0000000000
--- a/include/configs/EXBITGEN.h
+++ /dev/null
@@ -1,190 +0,0 @@
-/*
- * (C) Copyright 2000-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405GP		1	/* This is a PPC405GP CPU	*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
-#define CONFIG_EXBITGEN		1	/* on a Exbit Generic board     */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
-
-#define CONFIG_SYS_CLK_FREQ     25000000 /* external frequency to pll   */
-
-/* I2C configuration */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#define CONFIG_SYS_I2C_SPEED		40000	/* I2C speed			*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F	/* I2C slave address		*/
-
-/* environment is in EEPROM */
-#define CONFIG_ENV_IS_IN_EEPROM    1
-#undef CONFIG_ENV_IS_IN_FLASH
-#undef CONFIG_ENV_IS_IN_NVRAM
-
-#ifdef CONFIG_ENV_IS_IN_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x56    /* 1010110 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1	/* 8-bit internal addressing */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	1	/* ... and 1 bit in I2C address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3	/* 4 bytes per page */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	40	/* write takes up to 40 msec */
-#define CONFIG_ENV_OFFSET		4	/* Offset of Environment Sector	*/
-#define	CONFIG_ENV_SIZE		350	/* that is 350 bytes only!	*/
-#endif
-
-#define CONFIG_BOOTDELAY	10	/* autoboot after 10 seconds	*/
-/* Explanation:
-   autbooting is altogether disabled and cannot be
-   enabled if CONFIG_BOOTDELAY is negative.
-   If you want shorter bootdelay, then
-   - "setenv bootdelay <delay>" to the proper value
-*/
-
-#define CONFIG_BOOTCOMMAND	"bootm 20400000 20800000"
-
-#define CONFIG_BOOTARGS		"root=/dev/ram "  \
-				"ramdisk_size=32768 " \
-				"console=ttyS0,115200 " \
-				"ram=128M debug"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_PHY_ADDR		0	/* PHY address			*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-/* UART configuration */
-#define CONFIG_SYS_BASE_BAUD		691200
-
-/* Default baud rate */
-#define CONFIG_BAUDRATE		115200
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE      \
-	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
-	 57600, 115200, 230400, 460800, 921600 }
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-#define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#undef CONFIG_PCI			/* no pci support	        */
-
-/*-----------------------------------------------------------------------
- * External peripheral base address
- *-----------------------------------------------------------------------
- */
-#undef  CONFIG_IDE_PCMCIA               /* no pcmcia interface required */
-#undef  CONFIG_IDE_LED                  /* no led for ide supported     */
-#undef  CONFIG_IDE_RESET                /* no reset for ide supported   */
-
-#define	CONFIG_SYS_KEY_REG_BASE_ADDR	0xF0100000
-#define	CONFIG_SYS_IR_REG_BASE_ADDR	0xF0200000
-#define	CONFIG_SYS_FPGA_REG_BASE_ADDR	0xF0300000
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH0_BASE		0xFFF80000
-#define CONFIG_SYS_FLASH0_SIZE		0x00080000
-#define CONFIG_SYS_FLASH1_BASE		0x20000000
-#define CONFIG_SYS_FLASH1_SIZE		0x02000000
-#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_FLASH0_BASE
-#define CONFIG_SYS_FLASH_SIZE		CONFIG_SYS_FLASH0_SIZE
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN		(192 * 1024)	/* Reserve 196 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
-
-#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH0_BASE
-#define CONFIG_SYS_RAMSTART
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	5	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	128	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_OFFSET		0x00060000 /* Offset of Environment Sector      */
-#define	CONFIG_ENV_SIZE		0x00010000 /* Total Size of Environment Sector	*/
-#define CONFIG_ENV_SECT_SIZE	0x00010000 /* see README - env sector total size */
-#endif
-
-/* On Chip Memory location/size */
-#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
-
-/* Global info and initial stack */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of on-chip SRAM	*/
-#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-#endif	/* __CONFIG_H */