am335x_evm: enable support for booting via USB

This adds necessary config options and a new build target,
am335x_evm_usbspl, to enable usb booting and fixes board_eth_init()
function to take into account that we may have USB ether support in SPL
now.  This uses the same MAC for both cpsw and USB, in order to match
ROM behavior.

The usbspl build target does not contain UART SPL, CPSW SPL or extra
environment settings, so that we may fit within our binary size
constraint.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Signed-off-by: Tom Rini <trini@ti.com>

1 files changed, 21 insertions, 17 deletions

diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
index 48e68967e5..441758fdf0 100644
--- a/board/ti/am335x/board.c
+++ b/board/ti/am335x/board.c
@@ -389,7 +389,8 @@ int board_late_init(void)
 }
 #endif
 
-#ifdef CONFIG_DRIVER_TI_CPSW
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
 static void cpsw_control(int enabled)
 {
 	/* VTP can be added here */
@@ -434,26 +435,26 @@ static struct cpsw_platform_data cpsw_data = {
 int board_eth_init(bd_t *bis)
 {
 	int rv, n = 0;
-#ifdef CONFIG_DRIVER_TI_CPSW
 	uint8_t mac_addr[6];
 	uint32_t mac_hi, mac_lo;
 
-	if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
-		printf("<ethaddr> not set. Reading from E-fuse\n");
-		/* try reading mac address from efuse */
-		mac_lo = readl(&cdev->macid0l);
-		mac_hi = readl(&cdev->macid0h);
-		mac_addr[0] = mac_hi & 0xFF;
-		mac_addr[1] = (mac_hi & 0xFF00) >> 8;
-		mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
-		mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
-		mac_addr[4] = mac_lo & 0xFF;
-		mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+	/* try reading mac address from efuse */
+	mac_lo = readl(&cdev->macid0l);
+	mac_hi = readl(&cdev->macid0h);
+	mac_addr[0] = mac_hi & 0xFF;
+	mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+	mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+	mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+	mac_addr[4] = mac_lo & 0xFF;
+	mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+	if (!getenv("ethaddr")) {
+		printf("<ethaddr> not set. Validating first E-fuse MAC\n");
 
 		if (is_valid_ether_addr(mac_addr))
 			eth_setenv_enetaddr("ethaddr", mac_addr);
-		else
-			goto try_usbether;
 	}
 
 	if (board_is_bone() || board_is_bone_lt() || board_is_idk()) {
@@ -494,8 +495,11 @@ int board_eth_init(bd_t *bis)
 				AR8051_RGMII_TX_CLK_DLY);
 	}
 #endif
-try_usbether:
-#if defined(CONFIG_USB_ETHER) && !defined(CONFIG_SPL_BUILD)
+#if defined(CONFIG_USB_ETHER) && \
+	(!defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_USBETH_SUPPORT))
+	if (is_valid_ether_addr(mac_addr))
+		eth_setenv_enetaddr("usbnet_devaddr", mac_addr);
+
 	rv = usb_eth_initialize(bis);
 	if (rv < 0)
 		printf("Error %d registering USB_ETHER\n", rv);