Merge branch 'master' of git://www.denx.de/git/u-boot-imx

3 files changed, 6 insertions, 69 deletions

diff --git a/board/freescale/common/pfuze.c b/board/freescale/common/pfuze.c
index 783c46d882..69afa83562 100644
--- a/board/freescale/common/pfuze.c
+++ b/board/freescale/common/pfuze.c
@@ -13,7 +13,8 @@
 int pfuze_mode_init(struct pmic *p, u32 mode)
 {
 	unsigned char offset, i, switch_num;
-	u32 id, ret;
+	u32 id;
+	int ret;
 
 	pmic_reg_read(p, PFUZE100_DEVICEID, &id);
 	id = id & 0xf;
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 581c9d5560..d20953d2ca 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -94,8 +94,9 @@ static void setup_iomux_enet(void)
 
 	/* Reset AR8031 PHY */
 	gpio_direction_output(IMX_GPIO_NR(1, 25) , 0);
-	udelay(500);
+	mdelay(10);
 	gpio_set_value(IMX_GPIO_NR(1, 25), 1);
+	udelay(100);
 }
 
 static iomux_v3_cfg_t const usdhc2_pads[] = {
@@ -340,39 +341,6 @@ int board_mmc_init(bd_t *bis)
 }
 #endif
 
-int mx6_rgmii_rework(struct phy_device *phydev)
-{
-	unsigned short val;
-
-	/* To enable AR8031 ouput a 125MHz clk from CLK_25M */
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
-
-	val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
-	val &= 0xffe3;
-	val |= 0x18;
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
-
-	/* introduce tx clock delay */
-	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
-	val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
-	val |= 0x0100;
-	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
-
-	return 0;
-}
-
-int board_phy_config(struct phy_device *phydev)
-{
-	mx6_rgmii_rework(phydev);
-
-	if (phydev->drv->config)
-		phydev->drv->config(phydev);
-
-	return 0;
-}
-
 #if defined(CONFIG_VIDEO_IPUV3)
 static void disable_lvds(struct display_info_t const *dev)
 {
diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c
index 0af63d291f..ac001edf3a 100644
--- a/board/wandboard/wandboard.c
+++ b/board/wandboard/wandboard.c
@@ -121,8 +121,9 @@ static void setup_iomux_enet(void)
 
 	/* Reset AR8031 PHY */
 	gpio_direction_output(ETH_PHY_RESET, 0);
-	udelay(500);
+	mdelay(10);
 	gpio_set_value(ETH_PHY_RESET, 1);
+	udelay(100);
 }
 
 static struct fsl_esdhc_cfg usdhc_cfg[2] = {
@@ -187,39 +188,6 @@ int board_mmc_init(bd_t *bis)
 	return 0;
 }
 
-static int mx6_rgmii_rework(struct phy_device *phydev)
-{
-	unsigned short val;
-
-	/* To enable AR8031 ouput a 125MHz clk from CLK_25M */
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
-
-	val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
-	val &= 0xffe3;
-	val |= 0x18;
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
-
-	/* introduce tx clock delay */
-	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
-	val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
-	val |= 0x0100;
-	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
-
-	return 0;
-}
-
-int board_phy_config(struct phy_device *phydev)
-{
-	mx6_rgmii_rework(phydev);
-
-	if (phydev->drv->config)
-		phydev->drv->config(phydev);
-
-	return 0;
-}
-
 #if defined(CONFIG_VIDEO_IPUV3)
 struct i2c_pads_info mx6q_i2c2_pad_info = {
 	.scl = {