Merge with git://www.denx.de/git/u-boot.git

33 files changed, 2653 insertions, 152 deletions

diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c
index b5bb145808..6260b016df 100644
--- a/board/amcc/bamboo/bamboo.c
+++ b/board/amcc/bamboo/bamboo.c
@@ -277,87 +277,6 @@ int board_early_init_f(void)
 	return 0;
 }
 
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-/*----------------------------------------------------------------------------+
-  | nand_reset.
-  |   Reset Nand flash
-  |   This routine will abort previous cmd
-  +----------------------------------------------------------------------------*/
-int nand_reset(ulong addr)
-{
-	int wait=0, stat=0;
-
-	out8(addr + NAND_CMD_REG, NAND0_CMD_RESET);
-	out8(addr + NAND_CMD_REG, NAND0_CMD_READ_STATUS);
-
-	while ((stat != 0xc0) && (wait != 0xffff)) {
-		stat = in8(addr + NAND_DATA_REG);
-		wait++;
-	}
-
-	if (stat == 0xc0) {
-		return 0;
-	} else {
-		printf("NAND Reset timeout.\n");
-		return -1;
-	}
-}
-
-void board_nand_set_device(int cs, ulong addr)
-{
-	/* Set NandFlash Core Configuration Register */
-	out32(addr + NAND_CCR_REG, 0x00001000 | (cs << 24));
-
-	switch (cs) {
-	case 1:
-		/* -------
-		 *  NAND0
-		 * -------
-		 * K9F1208U0A : 4 addr cyc, 1 col + 3 Row
-		 * Set NDF1CR - Enable External CS1 in NAND FLASH controller
-		 */
-		out32(addr + NAND_CR1_REG, 0x80002222);
-		break;
-
-	case 2:
-		/* -------
-		 *  NAND1
-		 * -------
-		 * K9K2G0B : 5 addr cyc, 2 col + 3 Row
-		 * Set NDF2CR : Enable External CS2 in NAND FLASH controller
-		 */
-		out32(addr + NAND_CR2_REG, 0xC0007777);
-		break;
-	}
-
-	/* Perform Reset Command */
-	if (nand_reset(addr) != 0)
-		return;
-}
-
-void nand_init(void)
-{
-	board_nand_set_device(1, CFG_NAND_ADDR);
-
-	nand_probe(CFG_NAND_ADDR);
-	if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
-		print_size(nand_dev_desc[0].totlen, "\n");
-	}
-
-#if 0 /* NAND1 not supported yet */
-	board_nand_set_device(2, CFG_NAND2_ADDR);
-
-	nand_probe(CFG_NAND2_ADDR);
-	if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
-		print_size(nand_dev_desc[0].totlen, "\n");
-	}
-#endif
-}
-#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */
-
 int checkboard(void)
 {
 	char *s = getenv("serial#");
diff --git a/board/amcc/bamboo/u-boot.lds b/board/amcc/bamboo/u-boot.lds
index 176900ec2f..f6d7183199 100644
--- a/board/amcc/bamboo/u-boot.lds
+++ b/board/amcc/bamboo/u-boot.lds
@@ -68,19 +68,7 @@ SECTIONS
 
     cpu/ppc4xx/start.o	(.text)
     board/amcc/bamboo/init.o	(.text)
-    cpu/ppc4xx/kgdb.o	(.text)
-    cpu/ppc4xx/traps.o	(.text)
-    cpu/ppc4xx/interrupts.o	(.text)
-    cpu/ppc4xx/serial.o	(.text)
-    cpu/ppc4xx/cpu_init.o	(.text)
-    cpu/ppc4xx/speed.o	(.text)
-    common/dlmalloc.o	(.text)
-    lib_generic/crc32.o		(.text)
-    lib_ppc/extable.o	(.text)
-    lib_generic/zlib.o		(.text)
-
-/*    . = env_offset;*/
-/*    common/environment.o(.text)*/
+    board/amcc/bamboo/bamboo.o	(.text)
 
     *(.text)
     *(.fixup)
diff --git a/board/amcc/sequoia/sdram.c b/board/amcc/sequoia/sdram.c
index f8b837ed28..d045df1872 100644
--- a/board/amcc/sequoia/sdram.c
+++ b/board/amcc/sequoia/sdram.c
@@ -371,6 +371,14 @@ void denali_core_search_data_eye(unsigned long memory_size)
 }
 #endif /* CONFIG_DDR_DATA_EYE */
 
+#if defined(CONFIG_NAND_SPL)
+/* Using cpu/ppc4xx/speed.c to calculate the bus frequency is too big
+ * for the 4k NAND boot image so define bus_frequency to 133MHz here
+ * which is save for the refresh counter setup.
+ */
+#define get_bus_freq(val)	133000000
+#endif
+
 /*************************************************************************
  *
  * initdram -- 440EPx's DDR controller is a DENALI Core
@@ -404,7 +412,7 @@ long int initdram (int board_type)
 	mtsdram(DDR0_22, 0x00267F0B);
 	mtsdram(DDR0_23, 0x00000000);
 	mtsdram(DDR0_24, 0x01010002);
-	if (speed > 133333333)
+	if (speed > 133333334)
 		mtsdram(DDR0_26, 0x5B26050C);
 	else
 		mtsdram(DDR0_26, 0x5B260408);
diff --git a/board/cds/mpc8541cds/mpc8541cds.c b/board/cds/mpc8541cds/mpc8541cds.c
index a42904cf73..4192324836 100644
--- a/board/cds/mpc8541cds/mpc8541cds.c
+++ b/board/cds/mpc8541cds/mpc8541cds.c
@@ -477,11 +477,14 @@ void dummy_func(struct pci_controller* hose, pci_dev_t dev, struct pci_config_ta
 static struct pci_config_table pci_mpc85xxcds_config_table[] = {
 	{0x10e3, 0x0513, PCI_ANY_ID, 1, 3, PCI_ANY_ID, dummy_func, {0,0,0}},
 	{0x1106, 0x0686, PCI_ANY_ID, 1, 2, 0, mpc85xx_config_via, {0,0,0}},
-	{0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1, mpc85xx_config_via_usbide, {0,0,0}},
+	{0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1,
+		mpc85xx_config_via_usbide, {0,0,0}},
 	{0x1105, 0x3038, PCI_ANY_ID, 1, 2, 2, mpc85xx_config_via_usb, {0,0,0}},
 	{0x1106, 0x3038, PCI_ANY_ID, 1, 2, 3, mpc85xx_config_via_usb2, {0,0,0}},
-	{0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5, mpc85xx_config_via_power, {0,0,0}},
-	{0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}}
+	{0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5,
+		mpc85xx_config_via_power, {0,0,0}},
+	{0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}},
+	{},
 };
 
 static struct pci_controller hose[] = {
diff --git a/board/cds/mpc8541cds/u-boot.lds b/board/cds/mpc8541cds/u-boot.lds
index 1bea0074fa..dc87a122a1 100644
--- a/board/cds/mpc8541cds/u-boot.lds
+++ b/board/cds/mpc8541cds/u-boot.lds
@@ -69,6 +69,7 @@ SECTIONS
     cpu/mpc85xx/interrupts.o (.text)
     cpu/mpc85xx/cpu_init.o (.text)
     cpu/mpc85xx/cpu.o (.text)
+    drivers/tsec.o (.text)
     cpu/mpc85xx/speed.o (.text)
     cpu/mpc85xx/pci.o (.text)
     common/dlmalloc.o (.text)
diff --git a/board/cds/mpc8548cds/init.S b/board/cds/mpc8548cds/init.S
index 978bda5e4d..d468f5b618 100644
--- a/board/cds/mpc8548cds/init.S
+++ b/board/cds/mpc8548cds/init.S
@@ -64,8 +64,9 @@ tlb1_entry:
 	/*
 	 * Number of TLB0 and TLB1 entries in the following table
 	 */
-	.long 13
+	.long (2f-1f)/16
 
+1:
 #if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
 	/*
 	 * TLB0		4K	Non-cacheable, guarded
@@ -134,7 +135,7 @@ tlb1_entry:
 
 	/*
 	 * TLB 1:	256M	Non-cacheable, guarded
-	 * 0x80000000	256M	PCI1 MEM First half
+	 * 0x80000000	256M	PCI1 MEM
 	 */
 	.long TLB1_MAS0(1, 1, 0)
 	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
@@ -143,40 +144,37 @@ tlb1_entry:
 
 	/*
 	 * TLB 2:	256M	Non-cacheable, guarded
-	 * 0x90000000	256M	PCI1 MEM Second half
+	 * 0x90000000	256M	PCI2 MEM
 	 */
 	.long TLB1_MAS0(1, 2, 0)
 	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
-	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000),
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE),
 			0,0,0,0,1,0,1,0)
-	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000),
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE),
 			0,0,0,0,0,1,0,1,0,1)
 
 	/*
-	 * TLB 3:	256M	Non-cacheable, guarded
-	 * 0xa0000000	256M	PCI2 MEM First half
+	 * TLB 3:	1GB	Non-cacheable, guarded
+	 * 0xa0000000	256M	PEX MEM First half
+	 * 0xb0000000	256M	PEX MEM Second half
+	 * 0xc0000000	256M	Rapid IO MEM First half
+	 * 0xd0000000	256M	Rapid IO MEM Second half
 	 */
 	.long TLB1_MAS0(1, 3, 0)
-	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
-	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE), 0,0,0,0,1,0,1,0)
-	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PEX_MEM_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PEX_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
 
 	/*
-	 * TLB 4:	256M	Non-cacheable, guarded
-	 * 0xb0000000	256M	PCI2 MEM Second half
+	 * TLB 4:	Reserved for future usage
 	 */
-	.long TLB1_MAS0(1, 4, 0)
-	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
-	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE + 0x10000000),
-			0,0,0,0,1,0,1,0)
-	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE + 0x10000000),
-			0,0,0,0,0,1,0,1,0,1)
 
 	/*
 	 * TLB 5:	64M	Non-cacheable, guarded
 	 * 0xe000_0000	1M	CCSRBAR
-	 * 0xe200_0000	16M	PCI1 IO
-	 * 0xe300_0000	16M	PCI2 IO
+	 * 0xe200_0000	8M	PCI1 IO
+	 * 0xe280_0000	8M	PCI2 IO
+	 * 0xe300_0000	16M	PEX IO
 	 */
 	.long TLB1_MAS0(1, 5, 0)
 	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
@@ -200,19 +198,22 @@ tlb1_entry:
 	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M)
 	.long TLB1_MAS2(E500_TLB_EPN(CADMUS_BASE_ADDR), 0,0,0,0,1,0,1,0)
 	.long TLB1_MAS3(E500_TLB_RPN(CADMUS_BASE_ADDR), 0,0,0,0,0,1,0,1,0,1)
-
+2:
 	entry_end
 
 /*
  * LAW(Local Access Window) configuration:
  *
  * 0x0000_0000     0x7fff_ffff     DDR                     2G
- * 0x8000_0000     0x9fff_ffff     PCI1 MEM                512M
- * 0xa000_0000     0xbfff_ffff     PCI2 MEM                512M
+ * 0x8000_0000     0x8fff_ffff     PCI1 MEM                256M
+ * 0x9000_0000     0x9fff_ffff     PCI2 MEM                256M
+ * 0xa000_0000     0xbfff_ffff     PEX MEM                 512M
+ * 0xc000_0000     0xdfff_ffff     RapidIO                 512M
  * 0xe000_0000     0xe000_ffff     CCSR                    1M
- * 0xe200_0000     0xe20f_ffff     PCI1 IO                 1M
- * 0xe210_0000     0xe21f_ffff     PCI2 IO                 1M
- * 0xf000_0000     0xf7ff_ffff     SDRAM                   128M
+ * 0xe200_0000     0xe27f_ffff     PCI1 IO                 8M
+ * 0xe280_0000     0xe2ff_ffff     PCI2 IO                 8M
+ * 0xe300_0000     0xe3ff_ffff     PEX IO                  16M
+ * 0xf000_0000     0xf3ff_ffff     SDRAM                   64M
  * 0xf800_0000     0xf80f_ffff     NVRAM/CADMUS (*)        1M
  * 0xff00_0000     0xff7f_ffff     FLASH (2nd bank)        8M
  * 0xff80_0000     0xffff_ffff     FLASH (boot bank)       8M
@@ -229,27 +230,39 @@ tlb1_entry:
 #define LAWAR0  ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
 
 #define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
-#define LAWAR1 	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M))
+#define LAWAR1 	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_256M))
 
 #define LAWBAR2 ((CFG_PCI2_MEM_BASE>>12) & 0xfffff)
-#define LAWAR2 	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M))
+#define LAWAR2 	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_256M))
 
 #define LAWBAR3 ((CFG_PCI1_IO_PHYS>>12) & 0xfffff)
-#define LAWAR3 	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_1M))
+#define LAWAR3 	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_8M))
 
 #define LAWBAR4 ((CFG_PCI2_IO_PHYS>>12) & 0xfffff)
-#define LAWAR4 	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_1M))
+#define LAWAR4 	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_8M))
 
 /* LBC window - maps 256M 0xf0000000 -> 0xffffffff */
 #define LAWBAR5 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
 #define LAWAR5 	(LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
 
+#define LAWBAR6 ((CFG_PEX_MEM_BASE>>12) & 0xfffff)
+#define LAWAR6 	(LAWAR_EN | LAWAR_TRGT_IF_PEX | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+#define LAWBAR7 ((CFG_PEX_IO_PHYS>>12) & 0xfffff)
+#define LAWAR7 	(LAWAR_EN | LAWAR_TRGT_IF_PEX | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+#define LAWBAR8 ((CFG_RIO_MEM_BASE>>12) & 0xfffff)
+#define LAWAR8  (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
 	.section .bootpg, "ax"
 	.globl	law_entry
 
 law_entry:
 	entry_start
-	.long 6
+	.long (4f-3f)/8
+3:
 	.long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3
-	.long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5
+	.long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5,LAWBAR6,LAWAR6,LAWBAR7,LAWAR7
+	.long LAWBAR8,LAWAR8
+4:
 	entry_end
diff --git a/board/cds/mpc8548cds/mpc8548cds.c b/board/cds/mpc8548cds/mpc8548cds.c
index 7433ebf25b..929ff2e662 100644
--- a/board/cds/mpc8548cds/mpc8548cds.c
+++ b/board/cds/mpc8548cds/mpc8548cds.c
@@ -51,6 +51,7 @@ int checkboard (void)
 {
 	volatile immap_t *immap = (immap_t *) CFG_CCSRBAR;
 	volatile ccsr_gur_t *gur = &immap->im_gur;
+	volatile ccsr_local_ecm_t *ecm = &immap->im_local_ecm;
 
 	/* PCI slot in USER bits CSR[6:7] by convention. */
 	uint pci_slot = get_pci_slot ();
@@ -89,6 +90,12 @@ int checkboard (void)
 	 */
 	local_bus_init ();
 
+	/*
+	 * Fix CPU2 errata: A core hang possible while executing a
+	 * msync instruction and a snoopable transaction from an I/O
+	 * master tagged to make quick forward progress is present.
+	 */
+	ecm->eebpcr |= (1 << 16);
 
 	/*
 	 * Hack TSEC 3 and 4 IO voltages.
@@ -303,11 +310,14 @@ void dummy_func(struct pci_controller* hose, pci_dev_t dev, struct pci_config_ta
 static struct pci_config_table pci_mpc85xxcds_config_table[] = {
 	{0x10e3, 0x0513, PCI_ANY_ID, 1, 3, PCI_ANY_ID, dummy_func, {0,0,0}},
 	{0x1106, 0x0686, PCI_ANY_ID, 1, 2, 0, mpc85xx_config_via, {0,0,0}},
-	{0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1, mpc85xx_config_via_usbide, {0,0,0}},
+	{0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1,
+		mpc85xx_config_via_usbide, {0,0,0}},
 	{0x1105, 0x3038, PCI_ANY_ID, 1, 2, 2, mpc85xx_config_via_usb, {0,0,0}},
 	{0x1106, 0x3038, PCI_ANY_ID, 1, 2, 3, mpc85xx_config_via_usb2, {0,0,0}},
-	{0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5, mpc85xx_config_via_power, {0,0,0}},
-	{0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}}
+	{0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5,
+		mpc85xx_config_via_power, {0,0,0}},
+	{0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}},
+	{},
 };
 
 static struct pci_controller hose[] = {
diff --git a/board/cds/mpc8548cds/u-boot.lds b/board/cds/mpc8548cds/u-boot.lds
index 2c8fe9603d..c1f3495d75 100644
--- a/board/cds/mpc8548cds/u-boot.lds
+++ b/board/cds/mpc8548cds/u-boot.lds
@@ -69,6 +69,7 @@ SECTIONS
     cpu/mpc85xx/interrupts.o (.text)
     cpu/mpc85xx/cpu_init.o (.text)
     cpu/mpc85xx/cpu.o (.text)
+    drivers/tsec.o (.text)
     cpu/mpc85xx/speed.o (.text)
     cpu/mpc85xx/pci.o (.text)
     common/dlmalloc.o (.text)
diff --git a/board/cds/mpc8555cds/mpc8555cds.c b/board/cds/mpc8555cds/mpc8555cds.c
index d980ea6310..704bf03164 100644
--- a/board/cds/mpc8555cds/mpc8555cds.c
+++ b/board/cds/mpc8555cds/mpc8555cds.c
@@ -474,11 +474,14 @@ void dummy_func(struct pci_controller* hose, pci_dev_t dev, struct pci_config_ta
 static struct pci_config_table pci_mpc85xxcds_config_table[] = {
 	{0x10e3, 0x0513, PCI_ANY_ID, 1, 3, PCI_ANY_ID, dummy_func, {0,0,0}},
 	{0x1106, 0x0686, PCI_ANY_ID, 1, 2, 0, mpc85xx_config_via, {0,0,0}},
-	{0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1, mpc85xx_config_via_usbide, {0,0,0}},
+	{0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1,
+		mpc85xx_config_via_usbide, {0,0,0}},
 	{0x1105, 0x3038, PCI_ANY_ID, 1, 2, 2, mpc85xx_config_via_usb, {0,0,0}},
 	{0x1106, 0x3038, PCI_ANY_ID, 1, 2, 3, mpc85xx_config_via_usb2, {0,0,0}},
-	{0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5, mpc85xx_config_via_power, {0,0,0}},
-	{0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}}
+	{0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5,
+		mpc85xx_config_via_power, {0,0,0}},
+	{0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}},
+	{},
 };
 
 
@@ -487,7 +490,7 @@ static struct pci_controller hose[] = {
 	config_table: pci_mpc85xxcds_config_table,
 	},
 #ifdef CONFIG_MPC85XX_PCI2
-	{ }
+	{},
 #endif
 };
 
diff --git a/board/cds/mpc8555cds/u-boot.lds b/board/cds/mpc8555cds/u-boot.lds
index 2aa2ad78fc..9285928dc4 100644
--- a/board/cds/mpc8555cds/u-boot.lds
+++ b/board/cds/mpc8555cds/u-boot.lds
@@ -69,6 +69,7 @@ SECTIONS
     cpu/mpc85xx/interrupts.o (.text)
     cpu/mpc85xx/cpu_init.o (.text)
     cpu/mpc85xx/cpu.o (.text)
+    drivers/tsec.o (.text)
     cpu/mpc85xx/speed.o (.text)
     cpu/mpc85xx/pci.o (.text)
     common/dlmalloc.o (.text)
diff --git a/board/freescale/mpc8544ds/Makefile b/board/freescale/mpc8544ds/Makefile
new file mode 100644
index 0000000000..bec2168639
--- /dev/null
+++ b/board/freescale/mpc8544ds/Makefile
@@ -0,0 +1,58 @@
+#
+# Copyright 2007 Freescale Semiconductor, Inc.
+# (C) Copyright 2001-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+# ifneq ($(OBJTREE),$(SRCTREE))
+# $(shell mkdir -p $(obj)./common)
+# endif
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	:= $(BOARD).o \
+	   ../common/pixis.o
+
+SOBJS	:= init.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/mpc8544ds/config.mk b/board/freescale/mpc8544ds/config.mk
new file mode 100644
index 0000000000..85663ef02b
--- /dev/null
+++ b/board/freescale/mpc8544ds/config.mk
@@ -0,0 +1,32 @@
+#
+# Copyright 2007 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# mpc8544ds board
+#
+ifndef TEXT_BASE
+TEXT_BASE = 0xfff80000
+endif
+
+PLATFORM_CPPFLAGS += -DCONFIG_E500=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC8544=1
diff --git a/board/freescale/mpc8544ds/init.S b/board/freescale/mpc8544ds/init.S
new file mode 100644
index 0000000000..296fee5e60
--- /dev/null
+++ b/board/freescale/mpc8544ds/init.S
@@ -0,0 +1,243 @@
+/*
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+#include <asm/cache.h>
+#include <asm/mmu.h>
+#include <config.h>
+#include <mpc85xx.h>
+
+#define LAWAR_TRGT_PCI1		0x00000000
+#define LAWAR_TRGT_PCIE1	0x00200000
+#define LAWAR_TRGT_PCIE2	0x00100000
+#define LAWAR_TRGT_PCIE3	0x00300000
+#define LAWAR_TRGT_LBC		0x00400000
+#define LAWAR_TRGT_DDR		0x00f00000
+
+/*
+ * TLB0 and TLB1 Entries
+ *
+ * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR.
+ * However, CCSRBAR is then relocated to CFG_CCSRBAR right after
+ * these TLB entries are established.
+ *
+ * The TLB entries for DDR are dynamically setup in spd_sdram()
+ * and use TLB1 Entries 8 through 15 as needed according to the
+ * size of DDR memory.
+ *
+ * MAS0: tlbsel, esel, nv
+ * MAS1: valid, iprot, tid, ts, tsize
+ * MAS2: epn, sharen, x0, x1, w, i, m, g, e
+ * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr
+ */
+
+#define	entry_start \
+	mflr	r1 	;	\
+	bl	0f 	;
+
+#define	entry_end \
+0:	mflr	r0	;	\
+	mtlr	r1	;	\
+	blr		;
+
+
+	.section	.bootpg, "ax"
+	.globl	tlb1_entry
+tlb1_entry:
+	entry_start
+
+	/*
+	 * Number of TLB0 and TLB1 entries in the following table
+	 */
+	.long (2f-1f)/16
+1:
+	/*
+	 * TLB0		4K	Non-cacheable, guarded
+	 * 0xff700000	4K	Initial CCSRBAR mapping
+	 *
+	 * This ends up at a TLB0 Index==0 entry, and must not collide
+	 * with other TLB0 Entries.
+	 */
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB0		16K	Cacheable, guarded
+	 * Temporary Global data for initialization
+	 *
+	 * Use four 4K TLB0 entries.  These entries must be cacheable
+	 * as they provide the bootstrap memory before the memory
+	 * controler and real memory have been configured.
+	 *
+	 * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c,
+	 * and must not collide with other TLB0 entries.
+	 */
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR),
+			0,0,0,0,0,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+			0,0,0,0,0,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+			0,0,0,0,0,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+			0,0,0,0,0,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+
+	/*
+	 * TLB 0:	64M	Non-cacheable, guarded
+	 * 0xfc000000	64M	Covers FLASH at 0xFE800000 and 0xFF800000
+	 * Out of reset this entry is only 4K.
+	 */
+	.long TLB1_MAS0(1, 0, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_BOOT_BLOCK), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_BOOT_BLOCK), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 1:	1G	Non-cacheable, guarded
+	 * 0x80000000	1G	PCIE  8,9,a,b
+	 */
+	.long TLB1_MAS0(1, 1, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCIE_PHYS),
+		0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCIE_PHYS),
+		0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 2:	256M	Non-cacheable, guarded
+	 */
+	.long TLB1_MAS0(1, 2, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS),
+			0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS),	0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 3:	256M	Non-cacheable, guarded
+	 */
+	.long TLB1_MAS0(1, 3, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS + 0x10000000),
+			0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS + 0x10000000),
+			0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 4:	64M	Non-cacheable, guarded
+	 * 0xe000_0000	1M	CCSRBAR
+	 * 0xe100_0000	255M	PCI IO range
+	 */
+	.long TLB1_MAS0(1, 4, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
+
+#ifdef CFG_LBC_CACHE_BASE
+	/*
+	 * TLB 5:	64M	Cacheable, non-guarded
+	 */
+	.long TLB1_MAS0(1, 5, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_CACHE_BASE), 0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_CACHE_BASE), 0,0,0,0,0,1,0,1,0,1)
+#endif
+	/*
+	 * TLB 6:	64M	Non-cacheable, guarded
+	 * 0xf8000000	64M	PIXIS 0xF8000000 - 0xFBFFFFFF
+	 */
+	.long TLB1_MAS0(1, 6, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_NONCACHE_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_NONCACHE_BASE), 0,0,0,0,0,1,0,1,0,1)
+2:
+	entry_end
+
+/*
+ * LAW(Local Access Window) configuration:
+ *
+ *
+ * Notes:
+ *    CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ *    If flash is 8M at default position (last 8M), no LAW needed.
+ *
+ * LAW 0 is reserved for boot mapping
+ */
+
+	.section .bootpg, "ax"
+	.globl	law_entry
+law_entry:
+	entry_start
+
+	.long (4f-3f)/8
+3:
+	.long	0
+	.long	(LAWAR_TRGT_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN
+
+	.long	(CFG_PCI1_MEM_BASE>>12) & 0xfffff
+	.long	LAWAR_EN | LAWAR_TRGT_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M)
+
+	.long	(CFG_PCI1_IO_PHYS>>12) & 0xfffff
+	.long	LAWAR_EN | LAWAR_TRGT_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M)
+
+	.long	(CFG_LBC_CACHE_BASE>>12) & 0xfffff
+	.long	LAWAR_EN | LAWAR_TRGT_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M)
+
+	.long	(CFG_PCIE1_MEM_PHYS>>12) & 0xfffff
+	.long	LAWAR_EN | LAWAR_TRGT_PCIE1 | (LAWAR_SIZE & LAWAR_SIZE_256M)
+
+	/* To keep to 10 LAWs, PCIE1_IO_PHYS must use top of mem region  */
+
+	.long	(CFG_PCIE2_MEM_PHYS>>12) & 0xfffff
+	.long	LAWAR_EN | LAWAR_TRGT_PCIE2 | (LAWAR_SIZE & LAWAR_SIZE_512M)
+
+	.long	(CFG_PCIE2_IO_PHYS>>12) & 0xfffff
+	.long	LAWAR_EN | LAWAR_TRGT_PCIE2 | (LAWAR_SIZE & LAWAR_SIZE_16M)
+
+	.long	(CFG_PCIE3_MEM_PHYS>>12) & 0xfffff
+	.long	LAWAR_EN | LAWAR_TRGT_PCIE3 | (LAWAR_SIZE & LAWAR_SIZE_256M)
+
+	.long	(CFG_PCIE3_IO_PHYS>>12) & 0xfffff
+	.long	LAWAR_EN | LAWAR_TRGT_PCIE3 | (LAWAR_SIZE & LAWAR_SIZE_16M)
+4:
+	entry_end
diff --git a/board/freescale/mpc8544ds/mpc8544ds.c b/board/freescale/mpc8544ds/mpc8544ds.c
new file mode 100644
index 0000000000..4ff1da9301
--- /dev/null
+++ b/board/freescale/mpc8544ds/mpc8544ds.c
@@ -0,0 +1,201 @@
+/*
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <spd.h>
+#include <miiphy.h>
+
+#include "../common/pixis.h"
+
+#if defined(CONFIG_OF_FLAT_TREE)
+#include <ft_build.h>
+extern void ft_cpu_setup(void *blob, bd_t *bd);
+#endif
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+extern long int spd_sdram(void);
+
+void sdram_init(void);
+
+int board_early_init_f (void)
+{
+	return 0;
+}
+
+int checkboard (void)
+{
+	volatile immap_t *immap = (immap_t *) CFG_CCSRBAR;
+	volatile ccsr_gur_t *gur = &immap->im_gur;
+
+	if ((uint)&gur->porpllsr != 0xe00e0000) {
+		printf("immap size error %x\n",&gur->porpllsr);
+	}
+	printf ("Board: MPC8544DS\n");
+
+	return 0;
+}
+
+long int
+initdram(int board_type)
+{
+	long dram_size = 0;
+
+	puts("Initializing\n");
+
+	dram_size = spd_sdram();
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+	/*
+	 * Initialize and enable DDR ECC.
+	 */
+	ddr_enable_ecc(dram_size);
+#endif
+	puts("    DDR: ");
+	return dram_size;
+}
+
+#if defined(CFG_DRAM_TEST)
+int
+testdram(void)
+{
+	uint *pstart = (uint *) CFG_MEMTEST_START;
+	uint *pend = (uint *) CFG_MEMTEST_END;
+	uint *p;
+
+	printf("Testing DRAM from 0x%08x to 0x%08x\n",
+	       CFG_MEMTEST_START,
+	       CFG_MEMTEST_END);
+
+	printf("DRAM test phase 1:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0xaaaaaaaa;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0xaaaaaaaa) {
+			printf ("DRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("DRAM test phase 2:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0x55555555;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0x55555555) {
+			printf ("DRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("DRAM test passed.\n");
+	return 0;
+}
+#endif
+
+int last_stage_init(void)
+{
+	return 0;
+}
+
+
+unsigned long
+get_board_sys_clk(ulong dummy)
+{
+	u8 i, go_bit, rd_clks;
+	ulong val = 0;
+
+	go_bit = in8(PIXIS_BASE + PIXIS_VCTL);
+	go_bit &= 0x01;
+
+	rd_clks = in8(PIXIS_BASE + PIXIS_VCFGEN0);
+	rd_clks &= 0x1C;
+
+	/*
+	 * Only if both go bit and the SCLK bit in VCFGEN0 are set
+	 * should we be using the AUX register. Remember, we also set the
+	 * GO bit to boot from the alternate bank on the on-board flash
+	 */
+
+	if (go_bit) {
+		if (rd_clks == 0x1c)
+			i = in8(PIXIS_BASE + PIXIS_AUX);
+		else
+			i = in8(PIXIS_BASE + PIXIS_SPD);
+	} else {
+		i = in8(PIXIS_BASE + PIXIS_SPD);
+	}
+
+	i &= 0x07;
+
+	switch (i) {
+	case 0:
+		val = 33333333;
+		break;
+	case 1:
+		val = 40000000;
+		break;
+	case 2:
+		val = 50000000;
+		break;
+	case 3:
+		val = 66666666;
+		break;
+	case 4:
+		val = 83000000;
+		break;
+	case 5:
+		val = 100000000;
+		break;
+	case 6:
+		val = 133333333;
+		break;
+	case 7:
+		val = 166666666;
+		break;
+	}
+
+	return val;
+}
+
+#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+void
+ft_board_setup(void *blob, bd_t *bd)
+{
+	u32 *p;
+	int len;
+
+	ft_cpu_setup(blob, bd);
+
+	p = ft_get_prop(blob, "/memory/reg", &len);
+	if (p != NULL) {
+		*p++ = cpu_to_be32(bd->bi_memstart);
+		*p = cpu_to_be32(bd->bi_memsize);
+	}
+}
+#endif
diff --git a/board/freescale/mpc8544ds/u-boot.lds b/board/freescale/mpc8544ds/u-boot.lds
new file mode 100644
index 0000000000..1a8aaa9057
--- /dev/null
+++ b/board/freescale/mpc8544ds/u-boot.lds
@@ -0,0 +1,148 @@
+/*
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  .bootpg 0xFFFFF000 :
+  {
+    cpu/mpc85xx/start.o	(.bootpg)
+    board/freescale/mpc8544ds/init.o (.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/mpc85xx/start.o	(.text)
+    board/freescale/mpc8544ds/init.o (.text)
+    cpu/mpc85xx/traps.o (.text)
+    cpu/mpc85xx/interrupts.o (.text)
+    cpu/mpc85xx/cpu_init.o (.text)
+    cpu/mpc85xx/cpu.o (.text)
+    cpu/mpc85xx/speed.o (.text)
+    common/dlmalloc.o (.text)
+    lib_generic/crc32.o (.text)
+    lib_ppc/extable.o (.text)
+    lib_generic/zlib.o (.text)
+    *(.text)
+    *(.fixup)
+    *(.got1)
+   }
+    _etext = .;
+    PROVIDE (etext = .);
+    .rodata    :
+   {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+    *(.eh_frame)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
diff --git a/board/ixdp425/config.mk b/board/ixdp425/config.mk
index d49c0e7e6d..ecff8d7415 100644
--- a/board/ixdp425/config.mk
+++ b/board/ixdp425/config.mk
@@ -1,4 +1,2 @@
+#
 TEXT_BASE = 0x00f80000
-
-# include NPE ethernet driver
-BOARDLIBS = $(obj)cpu/ixp/npe/libnpe.a
diff --git a/board/mpc8540ads/init.S b/board/mpc8540ads/init.S
index 242cb9fbc1..544fde94c4 100644
--- a/board/mpc8540ads/init.S
+++ b/board/mpc8540ads/init.S
@@ -260,8 +260,8 @@ tlb1_entry:
 #define LAWBAR2 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
 #define LAWAR2	(LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
 
-#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
-#define LAWAR3	(LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_16M))
+#define LAWBAR3 ((CFG_PCI1_IO_PHYS>>12) & 0xfffff)
+#define LAWAR3	(LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_1M))
 
 /*
  * Rapid IO at 0xc000_0000 for 512 M
diff --git a/board/mpc8560ads/init.S b/board/mpc8560ads/init.S
index 242cb9fbc1..544fde94c4 100644
--- a/board/mpc8560ads/init.S
+++ b/board/mpc8560ads/init.S
@@ -260,8 +260,8 @@ tlb1_entry:
 #define LAWBAR2 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
 #define LAWAR2	(LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
 
-#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
-#define LAWAR3	(LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_16M))
+#define LAWBAR3 ((CFG_PCI1_IO_PHYS>>12) & 0xfffff)
+#define LAWAR3	(LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_1M))
 
 /*
  * Rapid IO at 0xc000_0000 for 512 M
diff --git a/board/mpc8568mds/Makefile b/board/mpc8568mds/Makefile
new file mode 100644
index 0000000000..a799aa4cc5
--- /dev/null
+++ b/board/mpc8568mds/Makefile
@@ -0,0 +1,58 @@
+#
+# Copyright 2004-2007 Freescale Semiconductor.
+# (C) Copyright 2001-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+endif
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	:= $(BOARD).o \
+	bcsr.o \
+	ft_board.o
+
+SOBJS	:= init.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/mpc8568mds/bcsr.c b/board/mpc8568mds/bcsr.c
new file mode 100644
index 0000000000..2e2e8cd18f
--- /dev/null
+++ b/board/mpc8568mds/bcsr.c
@@ -0,0 +1,49 @@
+/*
+ * Copyright 2007 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include "bcsr.h"
+
+void enable_8568mds_duart()
+{
+	volatile uint* duart_mux	= (uint *)(CFG_CCSRBAR + 0xe0060);
+	volatile uint* devices		= (uint *)(CFG_CCSRBAR + 0xe0070);
+	volatile u8 *bcsr		= (u8 *)(CFG_BCSR);
+
+	*duart_mux = 0x80000000;	/* Set the mux to Duart on PMUXCR */
+	*devices  = 0;			/* Enable all peripheral devices */
+	bcsr[5] |= 0x01;		/* Enable Duart in BCSR*/
+}
+
+void enable_8568mds_flash_write()
+{
+	volatile u8 *bcsr = (u8 *)(CFG_BCSR);
+
+	bcsr[9] |= 0x01;
+}
+
+void disable_8568mds_flash_write()
+{
+	volatile u8 *bcsr = (u8 *)(CFG_BCSR);
+
+	bcsr[9] &= ~(0x01);
+}
diff --git a/board/mpc8568mds/bcsr.h b/board/mpc8568mds/bcsr.h
new file mode 100644
index 0000000000..8d4cb2f141
--- /dev/null
+++ b/board/mpc8568mds/bcsr.h
@@ -0,0 +1,99 @@
+/*
+ * Copyright 2007 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __BCSR_H_
+#define __BCSR_H_
+
+#include <common.h>
+
+/* BCSR Bit definitions
+	* BCSR 0 *
+	0:3	ccb sys pll
+	4:6	cfg core pll
+	7	cfg boot seq
+
+	* BCSR 1 *
+	0:2 	cfg rom lock
+	3:5 	cfg host agent
+	6	PCI IO
+	7	cfg RIO size
+
+	* BCSR 2 *
+	0:4	QE PLL
+	5	QE clock
+	6	cfg PCI arbiter
+
+	* BCSR 3 *
+	0	TSEC1 reduce
+	1	TSEC2 reduce
+	2:3	TSEC1 protocol
+	4:5 	TSEC2 protocol
+	6	PHY1 slave
+	7	PHY2 slave
+
+	* BCSR 4 *
+	4	clock enable
+	5	boot EPROM
+	6	GETH transactive reset
+	7	BRD write potect
+
+	* BCSR 5 *
+	1:3	Leds 1-3
+	4	UPC1 enable
+	5	UPC2 enable
+	6	UPC2 pos
+	7	RS232 enable
+
+	* BCSR 6 *
+	0	CFG ver 0
+	1	CFG ver 1
+	6	Register config led
+	7	Power on reset
+
+	* BCSR 7 *
+	2 	board host mode indication
+	5 	enable TSEC1 PHY
+	6 	enable TSEC2 PHY
+
+	* BCSR 8 *
+	0	UCC GETH1 enable
+	1	UCC GMII enable
+	3	UCC TBI enable
+	5	UCC MII enable
+	7	Real time clock reset
+
+	* BCSR 9 *
+	0	UCC2 GETH enable
+	1	UCC2 GMII enable
+	3	UCC2 TBI enable
+	5	UCC2 MII enable
+	6	Ready only - indicate flash ready after burning
+	7	Flash write protect
+*/
+
+/*BCSR Utils functions*/
+
+void enable_8568mds_duart(void);
+void enable_8568mds_flash_write(void);
+void disable_8568mds_flash_write(void);
+
+#endif	/* __BCSR_H_ */
diff --git a/board/mpc8568mds/config.mk b/board/mpc8568mds/config.mk
new file mode 100644
index 0000000000..021522cafc
--- /dev/null
+++ b/board/mpc8568mds/config.mk
@@ -0,0 +1,30 @@
+#
+# Copyright 2007 Freescale Semiconductor.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# mpc8568mds board
+#
+TEXT_BASE = 0xfff80000
+
+PLATFORM_CPPFLAGS += -DCONFIG_E500=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC8568=1
diff --git a/board/mpc8568mds/ft_board.c b/board/mpc8568mds/ft_board.c
new file mode 100644
index 0000000000..36815ccfbb
--- /dev/null
+++ b/board/mpc8568mds/ft_board.c
@@ -0,0 +1,45 @@
+/*
+ * Copyright 2004-2007 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+#include <ft_build.h>
+
+extern void ft_cpu_setup(void *blob, bd_t *bd);
+
+#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+void
+ft_board_setup(void *blob, bd_t *bd)
+{
+	u32 *p;
+	int len;
+#ifdef CONFIG_PCI
+	ft_pci_setup(blob, bd);
+#endif
+	ft_cpu_setup(blob, bd);
+	p = ft_get_prop(blob, "/memory/reg", &len);
+	if (p != NULL) {
+		*p++ = cpu_to_be32(bd->bi_memstart);
+		*p = cpu_to_be32(bd->bi_memsize);
+	}
+}
+#endif /* CONFIG_OF_FLAT_TREE && CONFIG_OF_BOARD_SETUP */
diff --git a/board/mpc8568mds/init.S b/board/mpc8568mds/init.S
new file mode 100644
index 0000000000..0d879821e3
--- /dev/null
+++ b/board/mpc8568mds/init.S
@@ -0,0 +1,258 @@
+/*
+ * Copyright 2004-2007 Freescale Semiconductor.
+ * Copyright 2002,2003, Motorola Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+#include <asm/cache.h>
+#include <asm/mmu.h>
+#include <config.h>
+#include <mpc85xx.h>
+
+
+/*
+ * TLB0 and TLB1 Entries
+ *
+ * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR.
+ * However, CCSRBAR is then relocated to CFG_CCSRBAR right after
+ * these TLB entries are established.
+ *
+ * The TLB entries for DDR are dynamically setup in spd_sdram()
+ * and use TLB1 Entries 8 through 15 as needed according to the
+ * size of DDR memory.
+ *
+ * MAS0: tlbsel, esel, nv
+ * MAS1: valid, iprot, tid, ts, tsize
+ * MAS2: epn, sharen, x0, x1, w, i, m, g, e
+ * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr
+ */
+#define	entry_start \
+	mflr	r1	;	\
+	bl	0f	;
+
+#define	entry_end \
+0:	mflr	r0	;	\
+	mtlr	r1	;	\
+	blr		;
+
+
+	.section	.bootpg, "ax"
+	.globl	tlb1_entry
+tlb1_entry:
+	entry_start
+
+	/*
+	 * Number of TLB0 and TLB1 entries in the following table
+	 */
+	.long (2f-1f)/16
+
+1:
+#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
+	/*
+	 * TLB0		4K	Non-cacheable, guarded
+	 * 0xff700000	4K	Initial CCSRBAR mapping
+	 *
+	 * This ends up at a TLB0 Index==0 entry, and must not collide
+	 * with other TLB0 Entries.
+	 */
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1)
+#else
+#error("Update the number of table entries in tlb1_entry")
+#endif
+
+	/*
+	 * TLB0		16K	Cacheable, non-guarded
+	 * 0xd001_0000	16K	Temporary Global data for initialization
+	 *
+	 * Use four 4K TLB0 entries.  These entries must be cacheable
+	 * as they provide the bootstrap memory before the memory
+	 * controler and real memory have been configured.
+	 *
+	 * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c,
+	 * and must not collide with other TLB0 entries.
+	 */
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), 0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), 0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+	/* TLB 1 Initializations */
+	/*
+	 * TLBe 0:	16M	Non-cacheable, guarded
+	 * 0xff000000	16M	FLASH (upper half)
+	 * Out of reset this entry is only 4K.
+	 */
+	.long TLB1_MAS0(1, 0, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE + 0x1000000),
+			0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE + 0x1000000),
+			0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLBe 1:	16M	Non-cacheable, guarded
+	 * 0xfe000000	16M	FLASH (lower half)
+	 */
+	.long TLB1_MAS0(1, 1, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLBe 2:	256M	Non-cacheable, guarded
+	 * 0x80000000	256M	PCI1 MEM
+	 */
+	.long TLB1_MAS0(1, 2, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLBe 3:	256M	Non-cacheable, guarded
+	 * 0xa0000000	256M	PCIe Mem
+	 */
+	.long TLB1_MAS0(1, 3, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PEX_MEM_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PEX_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLBe 4:	Reserved for future usage
+	 */
+
+	/*
+	 * TLBe 5:	64M	Non-cacheable, guarded
+	 * 0xe000_0000	1M	CCSRBAR
+	 * 0xe200_0000	8M	PCI1 IO
+	 * 0xe280_0000	8M	PCIe IO
+	 */
+	.long TLB1_MAS0(1, 5, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLBe 6:	64M	Cacheable, non-guarded
+	 * 0xf000_0000	64M	LBC SDRAM
+	 */
+	.long TLB1_MAS0(1, 6, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLBe 7:	256K	Non-cacheable, guarded
+	 * 0xf8000000	32K BCSR
+	 * 0xf8008000	32K PIB (CS4)
+	 * 0xf8010000	32K PIB (CS5)
+	 */
+	.long TLB1_MAS0(1, 7, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256K)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_BCSR_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_BCSR_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+2:
+	entry_end
+
+/*
+ * LAW(Local Access Window) configuration:
+ *
+ *0)   0x0000_0000   0x7fff_ffff     DDR                     2G
+ *1)   0x8000_0000   0x9fff_ffff     PCI1 MEM                256MB
+ *2)   0xa000_0000   0xbfff_ffff     PCIe MEM                256MB
+ *5)   0xc000_0000   0xdfff_ffff     SRIO                    256MB
+ *-)   0xe000_0000   0xe00f_ffff     CCSR                    1M
+ *3)   0xe200_0000   0xe27f_ffff     PCI1 I/O                8M
+ *4)   0xe280_0000   0xe2ff_ffff     PCIe I/0                8M
+ *6.a) 0xf000_0000   0xf3ff_ffff     SDRAM                   64MB
+ *6.b) 0xf800_0000   0xf800_7fff     BCSR                    32KB
+ *6.c) 0xf800_8000   0xf800_ffff     PIB (CS4)		     32KB
+ *6.d) 0xf801_0000   0xf801_7fff     PIB (CS5)		     32KB
+ *6.e) 0xfe00_0000   0xffff_ffff     Flash                   32MB
+ *
+ *Notes:
+ *    CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ *    If flash is 8M at default position (last 8M), no LAW needed.
+ *
+ * The defines below are 1-off of the actual LAWAR0 usage.
+ * So LAWAR3 define uses the LAWAR4 register in the ECM.
+ */
+
+#define LAWBAR0 0
+#define LAWAR0  ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
+
+#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
+#define LAWAR1	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+#define LAWBAR2 ((CFG_PEX_MEM_BASE>>12) & 0xfffff)
+#define LAWAR2	(LAWAR_EN | LAWAR_TRGT_IF_PEX | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+#define LAWBAR3 ((CFG_PCI1_IO_PHYS>>12) & 0xfffff)
+#define LAWAR3	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_8M))
+
+#define LAWBAR4 ((CFG_PEX_IO_PHYS>>12) & 0xfffff)
+#define LAWAR4  (LAWAR_EN | LAWAR_TRGT_IF_PEX | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+
+#define LAWBAR5 ((CFG_SRIO_MEM_BASE>>12) & 0xfffff)
+#define LAWAR5	(LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+/* LBC window - maps 256M.  That's SDRAM, BCSR, PIBs, and Flash */
+#define LAWBAR6 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
+#define LAWAR6	(LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+	.section .bootpg, "ax"
+	.globl	law_entry
+
+law_entry:
+	entry_start
+	.long (4f-3f)/8
+3:
+	.long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3
+	.long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5,LAWBAR6,LAWAR6
+4:
+	entry_end
diff --git a/board/mpc8568mds/mpc8568mds.c b/board/mpc8568mds/mpc8568mds.c
new file mode 100644
index 0000000000..9c7960d47e
--- /dev/null
+++ b/board/mpc8568mds/mpc8568mds.c
@@ -0,0 +1,288 @@
+/*
+ * Copyright 2007 Freescale Semiconductor.
+ *
+ * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <spd.h>
+
+#include "bcsr.h"
+
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+extern long int spd_sdram(void);
+
+void local_bus_init(void);
+void sdram_init(void);
+
+int board_early_init_f (void)
+{
+	/*
+	 * Initialize local bus.
+	 */
+	local_bus_init ();
+
+	enable_8568mds_duart();
+	enable_8568mds_flash_write();
+
+	return 0;
+}
+
+int checkboard (void)
+{
+	printf ("Board: 8568 MDS\n");
+
+	return 0;
+}
+
+long int
+initdram(int board_type)
+{
+	long dram_size = 0;
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+
+	puts("Initializing\n");
+
+#if defined(CONFIG_DDR_DLL)
+	{
+		/*
+		 * Work around to stabilize DDR DLL MSYNC_IN.
+		 * Errata DDR9 seems to have been fixed.
+		 * This is now the workaround for Errata DDR11:
+		 *    Override DLL = 1, Course Adj = 1, Tap Select = 0
+		 */
+
+		volatile ccsr_gur_t *gur= &immap->im_gur;
+
+		gur->ddrdllcr = 0x81000000;
+		asm("sync;isync;msync");
+		udelay(200);
+	}
+#endif
+	dram_size = spd_sdram();
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+	/*
+	 * Initialize and enable DDR ECC.
+	 */
+	ddr_enable_ecc(dram_size);
+#endif
+	/*
+	 * SDRAM Initialization
+	 */
+	sdram_init();
+
+	puts("    DDR: ");
+	return dram_size;
+}
+
+/*
+ * Initialize Local Bus
+ */
+void
+local_bus_init(void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	volatile ccsr_gur_t *gur = &immap->im_gur;
+	volatile ccsr_lbc_t *lbc = &immap->im_lbc;
+
+	uint clkdiv;
+	uint lbc_hz;
+	sys_info_t sysinfo;
+
+	get_sys_info(&sysinfo);
+	clkdiv = (lbc->lcrr & 0x0f) * 2;
+	lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
+
+	gur->lbiuiplldcr1 = 0x00078080;
+	if (clkdiv == 16) {
+		gur->lbiuiplldcr0 = 0x7c0f1bf0;
+	} else if (clkdiv == 8) {
+		gur->lbiuiplldcr0 = 0x6c0f1bf0;
+	} else if (clkdiv == 4) {
+		gur->lbiuiplldcr0 = 0x5c0f1bf0;
+	}
+
+	lbc->lcrr |= 0x00030000;
+
+	asm("sync;isync;msync");
+}
+
+/*
+ * Initialize SDRAM memory on the Local Bus.
+ */
+void
+sdram_init(void)
+{
+#if defined(CFG_OR2_PRELIM) && defined(CFG_BR2_PRELIM)
+
+	uint idx;
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	volatile ccsr_lbc_t *lbc = &immap->im_lbc;
+	uint *sdram_addr = (uint *)CFG_LBC_SDRAM_BASE;
+	uint lsdmr_common;
+
+	puts("    SDRAM: ");
+
+	print_size (CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
+
+	/*
+	 * Setup SDRAM Base and Option Registers
+	 */
+	lbc->or2 = CFG_OR2_PRELIM;
+	asm("msync");
+
+	lbc->br2 = CFG_BR2_PRELIM;
+	asm("msync");
+
+	lbc->lbcr = CFG_LBC_LBCR;
+	asm("msync");
+
+
+	lbc->lsrt = CFG_LBC_LSRT;
+	lbc->mrtpr = CFG_LBC_MRTPR;
+	asm("msync");
+
+	/*
+	 * MPC8568 uses "new" 15-16 style addressing.
+	 */
+	lsdmr_common = CFG_LBC_LSDMR_COMMON;
+	lsdmr_common |= CFG_LBC_LSDMR_BSMA1516;
+
+	/*
+	 * Issue PRECHARGE ALL command.
+	 */
+	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_PCHALL;
+	asm("sync;msync");
+	*sdram_addr = 0xff;
+	ppcDcbf((unsigned long) sdram_addr);
+	udelay(100);
+
+	/*
+	 * Issue 8 AUTO REFRESH commands.
+	 */
+	for (idx = 0; idx < 8; idx++) {
+		lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_ARFRSH;
+		asm("sync;msync");
+		*sdram_addr = 0xff;
+		ppcDcbf((unsigned long) sdram_addr);
+		udelay(100);
+	}
+
+	/*
+	 * Issue 8 MODE-set command.
+	 */
+	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_MRW;
+	asm("sync;msync");
+	*sdram_addr = 0xff;
+	ppcDcbf((unsigned long) sdram_addr);
+	udelay(100);
+
+	/*
+	 * Issue NORMAL OP command.
+	 */
+	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_NORMAL;
+	asm("sync;msync");
+	*sdram_addr = 0xff;
+	ppcDcbf((unsigned long) sdram_addr);
+	udelay(200);    /* Overkill. Must wait > 200 bus cycles */
+
+#endif	/* enable SDRAM init */
+}
+
+#if defined(CFG_DRAM_TEST)
+int
+testdram(void)
+{
+	uint *pstart = (uint *) CFG_MEMTEST_START;
+	uint *pend = (uint *) CFG_MEMTEST_END;
+	uint *p;
+
+	printf("Testing DRAM from 0x%08x to 0x%08x\n",
+	       CFG_MEMTEST_START,
+	       CFG_MEMTEST_END);
+
+	printf("DRAM test phase 1:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0xaaaaaaaa;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0xaaaaaaaa) {
+			printf ("DRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("DRAM test phase 2:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0x55555555;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0x55555555) {
+			printf ("DRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("DRAM test passed.\n");
+	return 0;
+}
+#endif
+
+#if defined(CONFIG_PCI)
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_mpc8568mds_config_table[] = {
+	{
+	 PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
+	 pci_cfgfunc_config_device,
+	 {PCI_ENET0_IOADDR,
+	  PCI_ENET0_MEMADDR,
+	  PCI_COMMON_MEMORY | PCI_COMMAND_MASTER}
+	 },
+	{}
+};
+#endif
+
+static struct pci_controller hose[] = {
+#ifndef CONFIG_PCI_PNP
+	{ config_table: pci_mpc8568mds_config_table,},
+#endif
+#ifdef CONFIG_MPC85XX_PCI2
+	{},
+#endif
+};
+
+#endif	/* CONFIG_PCI */
+
+void
+pci_init_board(void)
+{
+#ifdef CONFIG_PCI
+	pci_mpc85xx_init(&hose);
+#endif
+}
diff --git a/board/mpc8568mds/u-boot.lds b/board/mpc8568mds/u-boot.lds
new file mode 100644
index 0000000000..71099f6f13
--- /dev/null
+++ b/board/mpc8568mds/u-boot.lds
@@ -0,0 +1,152 @@
+/*
+ * Copyright 2004-2007 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+
+SECTIONS
+{
+ /* ELIOR - From RAM:  From FLASH: 0xFFFFFFFC*/
+  .resetvec 0xFFFFFFFC:
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  /*(ELIOR - From RAM:  From FLASH: 0xFFFFF000*/
+  .bootpg 0xFFFFF000:
+  {
+	cpu/mpc85xx/start.o	(.bootpg)
+	board/mpc8568mds/init.o (.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/mpc85xx/start.o	(.text)
+    board/mpc8568mds/init.o (.text)
+    cpu/mpc85xx/traps.o (.text)
+    cpu/mpc85xx/interrupts.o (.text)
+    cpu/mpc85xx/cpu_init.o (.text)
+    cpu/mpc85xx/cpu.o (.text)
+    cpu/mpc85xx/speed.o (.text)
+    cpu/mpc85xx/pci.o (.text)
+    common/dlmalloc.o (.text)
+    lib_generic/crc32.o (.text)
+    lib_ppc/extable.o (.text)
+    lib_generic/zlib.o (.text)
+    *(.text)
+    *(.fixup)
+    *(.got1)
+   }
+    _etext = .;
+    PROVIDE (etext = .);
+    .rodata    :
+   {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+    *(.eh_frame)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
diff --git a/board/mpc8641hpcn/init.S b/board/mpc8641hpcn/init.S
index 6b3e2d275d..cb21ba6a75 100644
--- a/board/mpc8641hpcn/init.S
+++ b/board/mpc8641hpcn/init.S
@@ -59,7 +59,7 @@
 #define LAWAR2	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M))
 
 #define LAWBAR3 ((CFG_PCI2_MEM_BASE>>12) & 0xffffff)
-#define LAWAR3	(~LAWAR_EN & (LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M)))
+#define LAWAR3	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M))
 
 /*
  * This is not so much the SDRAM map as it is the whole localbus map.
@@ -67,11 +67,11 @@
 #define LAWBAR4 ((0xf8100000>>12) & 0xffffff)
 #define LAWAR4	(LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_2M))
 
-#define LAWBAR5 ((CFG_PCI1_IO_BASE>>12) & 0xffffff)
+#define LAWBAR5 ((CFG_PCI1_IO_PHYS>>12) & 0xffffff)
 #define LAWAR5	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M))
 
-#define LAWBAR6 ((CFG_PCI2_IO_BASE>>12) & 0xffffff)
-#define LAWAR6	(~LAWAR_EN &( LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_16M)))
+#define LAWBAR6 ((CFG_PCI2_IO_PHYS>>12) & 0xffffff)
+#define LAWAR6	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_16M))
 
 #define LAWBAR7 ((0xfe000000 >>12) & 0xffffff)
 #define LAWAR7	(LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_32M))
@@ -84,7 +84,7 @@
 #define LAWAR8  ((LAWAR_TRGT_IF_DDR2 | (LAWAR_SIZE & LAWAR_SIZE_512M)) & ~LAWAR_EN)
 #endif
 
-#define LAWBAR9 ((CFG_RIO_MEM_BASE>>12) & 0xfffff)
+#define LAWBAR9 ((CFG_RIO_MEM_PHYS>>12) & 0xfffff)
 #define LAWAR9  (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_512M))
 
 	.section .bootpg, "ax"
diff --git a/board/prodrive/pdnb3/config.mk b/board/prodrive/pdnb3/config.mk
index 767075884a..51dee86ae5 100644
--- a/board/prodrive/pdnb3/config.mk
+++ b/board/prodrive/pdnb3/config.mk
@@ -1,4 +1,2 @@
+#
 TEXT_BASE = 0x01f00000
-
-# include NPE ethernet driver
-BOARDLIBS = $(obj)cpu/ixp/npe/libnpe.a
diff --git a/board/stxssa/Makefile b/board/stxssa/Makefile
new file mode 100644
index 0000000000..344ecdfd79
--- /dev/null
+++ b/board/stxssa/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	:= $(BOARD).o
+SOBJS	:= init.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/stxssa/config.mk b/board/stxssa/config.mk
new file mode 100644
index 0000000000..30f42c53aa
--- /dev/null
+++ b/board/stxssa/config.mk
@@ -0,0 +1,34 @@
+# Modified by Xianghua Xiao, X.Xiao@motorola.com
+# (C) Copyright 2002,2003 Motorola Inc.
+#
+# Copied from ADS85xx for STx GP3 - Dan Malek
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# default CCARBAR is at 0xff700000
+# assume U-Boot is less than 0.5MB
+# U-Boot is less than 256K, so push
+# it further up into the flash
+#
+TEXT_BASE = 0xfffC0000
+
+PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_E500=1
diff --git a/board/stxssa/init.S b/board/stxssa/init.S
new file mode 100644
index 0000000000..a1a8d9e0cb
--- /dev/null
+++ b/board/stxssa/init.S
@@ -0,0 +1,256 @@
+/*
+ * Copyright (C) 2005 Embedded Alley Solutions, Inc.
+ * Dan Malek <dan@embeddedalley.com>
+ * Copied from STx GP3.
+ * Updates for Silicon Tx GP3 SSA.  We only support 32-bit flash
+ * and DDR with SPD EEPROM configuration.
+ *
+ * Copyright 2004 Freescale Semiconductor.
+ * Copyright (C) 2002,2003, Motorola Inc.
+ * Xianghua Xiao <X.Xiao@motorola.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+#include <asm/cache.h>
+#include <asm/mmu.h>
+#include <config.h>
+#include <mpc85xx.h>
+
+
+/*
+ * TLB0 and TLB1 Entries
+ *
+ * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR.
+ * However, CCSRBAR is then relocated to CFG_CCSRBAR right after
+ * these TLB entries are established.
+ *
+ * The TLB entries for DDR are dynamically setup in spd_sdram()
+ * and use TLB1 Entries 8 through 15 as needed according to the
+ * size of DDR memory.
+ *
+ * MAS0: tlbsel, esel, nv
+ * MAS1: valid, iprot, tid, ts, tsize
+ * MAS2: epn, sharen, x0, x1, w, i, m, g, e
+ * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr
+ */
+
+#define	entry_start \
+	mflr	r1 	;	\
+	bl	0f 	;
+
+#define	entry_end \
+0:	mflr	r0	;	\
+	mtlr	r1	;	\
+	blr		;
+
+
+	.section	.bootpg, "ax"
+	.globl	tlb1_entry
+tlb1_entry:
+	entry_start
+
+	/*
+	 * Number of TLB0 and TLB1 entries in the following table
+	 */
+	.long 12
+
+#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
+	/*
+	 * TLB0		4K	Non-cacheable, guarded
+	 * 0xff700000	4K	Initial CCSRBAR mapping
+	 *
+	 * This ends up at a TLB0 Index==0 entry, and must not collide
+	 * with other TLB0 Entries.
+	 */
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1)
+#else
+#error("Update the number of table entries in tlb1_entry")
+#endif
+
+	/*
+	 * TLB0		16K	Cacheable, non-guarded
+	 * 0xd001_0000	16K	Temporary Global data for initialization
+	 *
+	 * Use four 4K TLB0 entries.  These entries must be cacheable
+	 * as they provide the bootstrap memory before the memory
+	 * controler and real memory have been configured.
+	 *
+	 * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c,
+	 * and must not collide with other TLB0 entries.
+	 */
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), \
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), \
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), \
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), \
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), \
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), \
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), \
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), \
+			0,0,0,0,0,1,0,1,0,1)
+
+
+	/*
+	 * TLB 0:	64M	Non-cacheable, guarded
+	 * 0xfc000000	6M4	FLASH
+	 * Out of reset this entry is only 4K.
+	 */
+	.long TLB1_MAS0(1, 0, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 1:	256M	Non-cacheable, guarded
+	 * 0x80000000	256M	PCI1 MEM First half
+	 */
+	.long TLB1_MAS0(1, 1, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 2:	256M	Non-cacheable, guarded
+	 * 0x90000000	256M	PCI1 MEM Second half
+	 */
+	.long TLB1_MAS0(1, 2, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000), \
+			0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000), \
+			0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 3:	256M	Non-cacheable, guarded
+	 * 0xa0000000	256M	PCI2 MEM First half
+	 */
+	.long TLB1_MAS0(1, 3, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 4:	256M	Non-cacheable, guarded
+	 * 0xb0000000	256M	PCI2 MEM Second half
+	 */
+	.long TLB1_MAS0(1, 4, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE + 0x10000000), \
+			0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE + 0x10000000), \
+			0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 5:	64M	Non-cacheable, guarded
+	 * 0xe000_0000	1M	CCSRBAR
+	 * 0xe200_0000	16M	PCI1 IO
+	 * 0xe300_0000	16M	PCI2 IO
+	 */
+	.long TLB1_MAS0(1, 5, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 6:	256M	Non-cacheable, guarded
+	 * 0xf0000000		Local bus expansion option.
+	 * 0xfb000000		Configuration Latch register (one word)
+	 * 0xfc000000		Up to 64M flash
+	 */
+	.long TLB1_MAS0(1, 7, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_OPTION_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_OPTION_BASE), 0,0,0,0,0,1,0,1,0,1)
+	entry_end
+
+/*
+ * LAW(Local Access Window) configuration:
+ *
+ * 0x0000_0000     0x7fff_ffff     DDR                     2G
+ * 0x8000_0000     0x9fff_ffff     PCI1 MEM                512M
+ * 0xa000_0000     0xbfff_ffff     PCI2 MEM                512M
+ * 0xe000_0000     0xe000_ffff     CCSR                    1M
+ * 0xe200_0000     0xe2ff_ffff     PCI1 IO                 16M
+ * 0xe300_0000     0xe3ff_ffff     PCI2 IO                 16M
+ * 0xf000_0000     0xfaff_ffff     Local bus               128M
+ * 0xfb00_0000     0xfb00_ffff     Config Latch            64K
+ * 0xfc00_0000     0xffff_ffff     FLASH (boot bank)       64M
+ *
+ * Notes:
+ *    CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ *    If flash is 8M at default position (last 8M), no LAW needed.
+ */
+
+#if !defined(CONFIG_SPD_EEPROM)
+#define LAWBAR0 ((CFG_DDR_SDRAM_BASE>>12) & 0xfffff)
+#define LAWAR0	(LAWAR_EN | LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M))
+#else
+#define LAWBAR0 0
+#define LAWAR0  ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
+#endif
+
+#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
+#define LAWAR1 	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+#define LAWBAR2 ((CFG_PCI2_MEM_BASE>>12) & 0xfffff)
+#define LAWAR2 	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+#define LAWBAR3 ((CFG_PCI1_IO_PHYS>>12) & 0xfffff)
+#define LAWAR3 	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+#define LAWBAR4 ((CFG_PCI2_IO_PHYS>>12) & 0xfffff)
+#define LAWAR4 	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+/* Map the whole localbus, including flash and reset latch.
+*/
+#define LAWBAR5 ((CFG_LBC_OPTION_BASE>>12) & 0xfffff)
+#define LAWAR5	(LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+
+	.section .bootpg, "ax"
+	.globl	law_entry
+law_entry:
+	entry_start
+	.long 6
+	.long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3
+	.long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5
+	entry_end
diff --git a/board/stxssa/stxssa.c b/board/stxssa/stxssa.c
new file mode 100644
index 0000000000..0fb233d818
--- /dev/null
+++ b/board/stxssa/stxssa.c
@@ -0,0 +1,398 @@
+/*
+ * (C) Copyright 2005, Embedded Alley Solutions, Inc.
+ * Dan Malek, <dan@embeddedalley.com>
+ * Copied from STx GP3.
+ * Updates for Silicon Tx GP3 SSA
+ *
+ * (C) Copyright 2003,Motorola Inc.
+ * Xianghua Xiao, (X.Xiao@motorola.com)
+ *
+ * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+extern long int spd_sdram (void);
+
+#include <common.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <ioports.h>
+#include <asm/io.h>
+#include <spd.h>
+#include <miiphy.h>
+
+long int fixed_sdram (void);
+
+/*
+ * I/O Port configuration table
+ *
+ * if conf is 1, then that port pin will be configured at boot time
+ * according to the five values podr/pdir/ppar/psor/pdat for that entry
+ */
+
+const iop_conf_t iop_conf_tab[4][32] = {
+
+    /* Port A configuration */
+    {   /*            conf ppar psor pdir podr pdat */
+	/* PA31 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 TxENB */
+	/* PA30 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 TxClav   */
+	/* PA29 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 TxSOC  */
+	/* PA28 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 RxENB */
+	/* PA27 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 RxSOC */
+	/* PA26 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 RxClav */
+	/* PA25 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[0] */
+	/* PA24 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[1] */
+	/* PA23 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[2] */
+	/* PA22 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[3] */
+	/* PA21 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[4] */
+	/* PA20 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[5] */
+	/* PA19 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[6] */
+	/* PA18 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[7] */
+	/* PA17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[7] */
+	/* PA16 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[6] */
+	/* PA15 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[5] */
+	/* PA14 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[4] */
+	/* PA13 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[3] */
+	/* PA12 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[2] */
+	/* PA11 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[1] */
+	/* PA10 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[0] */
+	/* PA9  */ {   0,   1,   1,   1,   0,   0   }, /* FCC1 L1TXD */
+	/* PA8  */ {   0,   1,   1,   0,   0,   0   }, /* FCC1 L1RXD */
+	/* PA7  */ {   0,   0,   0,   1,   0,   0   }, /* PA7 */
+	/* PA6  */ {   0,   1,   1,   1,   0,   0   }, /* TDM A1 L1RSYNC */
+	/* PA5  */ {   0,   0,   0,   1,   0,   0   }, /* PA5 */
+	/* PA4  */ {   0,   0,   0,   1,   0,   0   }, /* PA4 */
+	/* PA3  */ {   0,   0,   0,   1,   0,   0   }, /* PA3 */
+	/* PA2  */ {   0,   0,   0,   1,   0,   0   }, /* PA2 */
+	/* PA1  */ {   1,   0,   0,   0,   0,   0   }, /* FREERUN */
+	/* PA0  */ {   0,   0,   0,   1,   0,   0   }  /* PA0 */
+    },
+
+    /* Port B configuration */
+    {   /*            conf ppar psor pdir podr pdat */
+	/* PB31 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TX_ER */
+	/* PB30 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_DV */
+	/* PB29 */ {   1,   1,   1,   1,   0,   0   }, /* FCC2 MII TX_EN */
+	/* PB28 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_ER */
+	/* PB27 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII COL */
+	/* PB26 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII CRS */
+	/* PB25 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[3] */
+	/* PB24 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[2] */
+	/* PB23 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[1] */
+	/* PB22 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[0] */
+	/* PB21 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[0] */
+	/* PB20 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[1] */
+	/* PB19 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[2] */
+	/* PB18 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[3] */
+	/* PB17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RX_DIV */
+	/* PB16 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RX_ERR */
+	/* PB15 */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TX_ERR */
+	/* PB14 */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TX_EN */
+	/* PB13 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:COL */
+	/* PB12 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:CRS */
+	/* PB11 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
+	/* PB10 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
+	/* PB9  */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
+	/* PB8  */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
+	/* PB7  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
+	/* PB6  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
+	/* PB5  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
+	/* PB4  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
+	/* PB3  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
+	/* PB2  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
+	/* PB1  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
+	/* PB0  */ {   0,   0,   0,   0,   0,   0   }  /* pin doesn't exist */
+    },
+
+    /* Port C */
+    {   /*            conf ppar psor pdir podr pdat */
+	/* PC31 */ {   0,   0,   0,   1,   0,   0   }, /* PC31 */
+	/* PC30 */ {   0,   0,   0,   1,   0,   0   }, /* PC30 */
+	/* PC29 */ {   0,   1,   1,   0,   0,   0   }, /* SCC1 EN *CLSN */
+	/* PC28 */ {   0,   0,   0,   1,   0,   0   }, /* PC28 */
+	/* PC27 */ {   0,   0,   0,   1,   0,   0   }, /* UART Clock in */
+	/* PC26 */ {   0,   0,   0,   1,   0,   0   }, /* PC26 */
+	/* PC25 */ {   0,   0,   0,   1,   0,   0   }, /* PC25 */
+	/* PC24 */ {   0,   0,   0,   1,   0,   0   }, /* PC24 */
+	/* PC23 */ {   0,   1,   0,   1,   0,   0   }, /* ATMTFCLK */
+	/* PC22 */ {   0,   1,   0,   0,   0,   0   }, /* ATMRFCLK */
+	/* PC21 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN RXCLK */
+	/* PC20 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN TXCLK */
+	/* PC19 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_CLK CLK13 */
+	/* PC18 */ {   1,   1,   0,   0,   0,   0   }, /* FCC Tx Clock (CLK14) */
+	/* PC17 */ {   0,   0,   0,   1,   0,   0   }, /* PC17 */
+	/* PC16 */ {   0,   1,   0,   0,   0,   0   }, /* FCC Tx Clock (CLK16) */
+	/* PC15 */ {   0,   1,   0,   0,   0,   0   }, /* PC15 */
+	/* PC14 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN *CD */
+	/* PC13 */ {   0,   0,   0,   1,   0,   0   }, /* PC13 */
+	/* PC12 */ {   0,   1,   0,   1,   0,   0   }, /* PC12 */
+	/* PC11 */ {   0,   0,   0,   1,   0,   0   }, /* LXT971 transmit control */
+	/* PC10 */ {   0,   0,   0,   1,   0,   0   }, /* FETHMDC */
+	/* PC9  */ {   0,   0,   0,   0,   0,   0   }, /* FETHMDIO */
+	/* PC8  */ {   0,   0,   0,   1,   0,   0   }, /* PC8 */
+	/* PC7  */ {   0,   0,   0,   1,   0,   0   }, /* PC7 */
+	/* PC6  */ {   0,   0,   0,   1,   0,   0   }, /* PC6 */
+	/* PC5  */ {   0,   0,   0,   1,   0,   0   }, /* PC5 */
+	/* PC4  */ {   0,   0,   0,   1,   0,   0   }, /* PC4 */
+	/* PC3  */ {   0,   0,   0,   1,   0,   0   }, /* PC3 */
+	/* PC2  */ {   0,   0,   0,   1,   0,   1   }, /* ENET FDE */
+	/* PC1  */ {   0,   0,   0,   1,   0,   0   }, /* ENET DSQE */
+	/* PC0  */ {   0,   0,   0,   1,   0,   0   }, /* ENET LBK */
+    },
+
+    /* Port D */
+    {   /*            conf ppar psor pdir podr pdat */
+	/* PD31 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN RxD */
+	/* PD30 */ {   0,   1,   1,   1,   0,   0   }, /* SCC1 EN TxD */
+	/* PD29 */ {   0,   1,   0,   1,   0,   0   }, /* SCC1 EN TENA */
+	/* PD28 */ {   1,   1,   0,   0,   0,   0   }, /* SCC2 RxD */
+	/* PD27 */ {   1,   1,   0,   1,   0,   0   }, /* SCC2 TxD */
+	/* PD26 */ {   0,   0,   0,   1,   0,   0   }, /* PD26 */
+	/* PD25 */ {   0,   0,   0,   1,   0,   0   }, /* PD25 */
+	/* PD24 */ {   0,   0,   0,   1,   0,   0   }, /* PD24 */
+	/* PD23 */ {   0,   0,   0,   1,   0,   0   }, /* PD23 */
+	/* PD22 */ {   0,   0,   0,   1,   0,   0   }, /* PD22 */
+	/* PD21 */ {   0,   0,   0,   1,   0,   0   }, /* PD21 */
+	/* PD20 */ {   0,   0,   0,   1,   0,   0   }, /* PD20 */
+	/* PD19 */ {   0,   0,   0,   1,   0,   0   }, /* PD19 */
+	/* PD18 */ {   0,   0,   0,   1,   0,   0   }, /* PD18 */
+	/* PD17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXPRTY */
+	/* PD16 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXPRTY */
+	/* PD15 */ {   1,   1,   1,   0,   1,   0   }, /* I2C SDA */
+	/* PD14 */ {   1,   1,   1,   0,   0,   0   }, /* I2C CLK */
+	/* PD13 */ {   0,   0,   0,   0,   0,   0   }, /* PD13 */
+	/* PD12 */ {   0,   0,   0,   0,   0,   0   }, /* PD12 */
+	/* PD11 */ {   0,   0,   0,   0,   0,   0   }, /* PD11 */
+	/* PD10 */ {   0,   0,   0,   0,   0,   0   }, /* PD10 */
+	/* PD9  */ {   0,   1,   0,   1,   0,   0   }, /* SMC1 TXD */
+	/* PD8  */ {   0,   1,   0,   0,   0,   0   }, /* SMC1 RXD */
+	/* PD7  */ {   0,   0,   0,   1,   0,   1   }, /* PD7 */
+	/* PD6  */ {   0,   0,   0,   1,   0,   1   }, /* PD6 */
+	/* PD5  */ {   0,   0,   0,   1,   0,   1   }, /* PD5 */
+	/* PD4  */ {   0,   0,   0,   1,   0,   1   }, /* PD4 */
+	/* PD3  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
+	/* PD2  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
+	/* PD1  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
+	/* PD0  */ {   0,   0,   0,   0,   0,   0   }  /* pin doesn't exist */
+    }
+};
+
+static	uint64_t	next_led_update;
+static	uint		led_bit;
+
+void
+reset_phy(void)
+{
+	volatile uint *blatch;
+#if 0
+	int	i;
+#endif
+	blatch = (volatile uint *)CFG_LBC_CFGLATCH_BASE;
+
+	/* reset Giga bit Ethernet port if needed here */
+
+#if 1
+	*blatch &= ~0x000000c0;
+	udelay(100);
+#else
+	*blatch = 0;
+	asm("eieio");
+	for (i=0; i<1000; i++)
+		udelay(1000);
+#endif
+	*blatch = 0x000000c1;	/* Light one led, too */
+	udelay(1000);
+
+#if 0	/* This is the port we really want to use for debugging. */
+	/* reset the CPM FEC port */
+#if (CONFIG_ETHER_INDEX == 2)
+	bcsr->bcsr2 &= ~FETH2_RST;
+	udelay(2);
+	bcsr->bcsr2 |=  FETH2_RST;
+	udelay(1000);
+#elif (CONFIG_ETHER_INDEX == 3)
+	bcsr->bcsr3 &= ~FETH3_RST;
+	udelay(2);
+	bcsr->bcsr3 |=  FETH3_RST;
+	udelay(1000);
+#endif
+#if defined(CONFIG_MII) && defined(CONFIG_ETHER_ON_FCC)
+	/* reset PHY */
+	miiphy_reset("FCC1 ETHERNET", 0x0);
+
+	/* change PHY address to 0x02 */
+	bb_miiphy_write(NULL, 0, PHY_MIPSCR, 0xf028);
+
+	bb_miiphy_write(NULL, 0x02, PHY_BMCR,
+			PHY_BMCR_AUTON | PHY_BMCR_RST_NEG);
+#endif /* CONFIG_MII */
+#endif
+}
+
+int
+board_early_init_f(void)
+{
+#if defined(CONFIG_PCI)
+    volatile immap_t *immr = (immap_t *)CFG_IMMR;
+    volatile ccsr_pcix_t *pci = &immr->im_pcix;
+
+    pci->peer &= 0xfffffffdf; /* disable master abort */
+#endif
+
+	/* Why is the phy reset done _after_ the ethernet
+	 * initialization in lib_ppc/board.c?
+	 * Do it here so it's done before the TSECs are used.
+	 */
+	reset_phy();
+
+	return 0;
+}
+
+int
+checkboard(void)
+{
+	printf ("Board: Silicon Tx GPPP SSA Board\n");
+	return (0);
+}
+
+/* Blinkin' LEDS for Robert.
+*/
+void
+show_activity(int flag)
+{
+	volatile uint *blatch;
+
+	if (next_led_update > get_ticks())
+		return;
+
+	blatch = (volatile uint *)CFG_LBC_CFGLATCH_BASE;
+
+	led_bit >>= 1;
+	if (led_bit == 0)
+		led_bit = 0x08;
+	*blatch = (0xc0 | led_bit);
+	eieio();
+	next_led_update += (get_tbclk() / 4);
+}
+
+long int
+initdram (int board_type)
+{
+	long dram_size = 0;
+	extern long spd_sdram (void);
+
+#if defined(CONFIG_DDR_DLL)
+	{
+		volatile immap_t *immap = (immap_t *)CFG_IMMR;
+		volatile ccsr_gur_t *gur= &immap->im_gur;
+		uint temp_ddrdll = 0;
+
+		/* Work around to stabilize DDR DLL */
+		temp_ddrdll = gur->ddrdllcr;
+		gur->ddrdllcr = ((temp_ddrdll & 0xff) << 16) | 0x80000000;
+		asm("sync;isync;msync");
+	}
+#endif
+
+	dram_size = spd_sdram ();
+
+#if defined(CONFIG_DDR_ECC)
+	/* Initialize and enable DDR ECC.
+	*/
+	ddr_enable_ecc(dram_size);
+#endif
+
+	return dram_size;
+}
+
+
+#if defined(CFG_DRAM_TEST)
+int testdram (void)
+{
+	uint *pstart = (uint *) CFG_MEMTEST_START;
+	uint *pend = (uint *) CFG_MEMTEST_END;
+	uint *p;
+
+	printf("SDRAM test phase 1:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0xaaaaaaaa;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0xaaaaaaaa) {
+			printf ("SDRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("SDRAM test phase 2:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0x55555555;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0x55555555) {
+			printf ("SDRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("SDRAM test passed.\n");
+	return 0;
+}
+#endif
+
+#if defined(CONFIG_PCI)
+
+/*
+ * Initialize PCI Devices, report devices found.
+ */
+
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_stxgp3_config_table[] = {
+    { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
+      PCI_IDSEL_NUMBER, PCI_ANY_ID,
+      pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
+				   PCI_ENET0_MEMADDR,
+				   PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER
+      } },
+    { }
+};
+#endif
+
+
+static struct pci_controller hose = {
+#ifndef CONFIG_PCI_PNP
+	config_table: pci_stxgp3_config_table,
+#endif
+};
+
+#endif	/* CONFIG_PCI */
+
+
+void
+pci_init_board(void)
+{
+#ifdef CONFIG_PCI
+	extern void pci_mpc85xx_init(struct pci_controller *hose);
+
+	pci_mpc85xx_init(&hose);
+#endif /* CONFIG_PCI */
+}
diff --git a/board/stxssa/u-boot.lds b/board/stxssa/u-boot.lds
new file mode 100644
index 0000000000..95ecf66a8d
--- /dev/null
+++ b/board/stxssa/u-boot.lds
@@ -0,0 +1,158 @@
+/*
+ * (C) Copyright 2005 Embedded Alley Solutions, Inc.
+ * Dan Malek, <dan@embeddedalley.com>
+ * Copied from STx GP3.
+ * Updates for Silicon Tx GP3 SSA.
+ *
+ * (C) Copyright 2002,2003,Motorola,Inc.
+ * Xianghua Xiao, X.Xiao@motorola.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  .bootpg 0xFFFFF000 :
+  {
+    cpu/mpc85xx/start.o	(.bootpg)
+    board/stxssa/init.o (.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/mpc85xx/start.o	(.text)
+    board/stxssa/init.o (.text)
+    cpu/mpc85xx/commproc.o (.text)
+    cpu/mpc85xx/traps.o (.text)
+    cpu/mpc85xx/interrupts.o (.text)
+    cpu/mpc85xx/serial_scc.o (.text)
+    cpu/mpc85xx/ether_fcc.o (.text)
+    cpu/mpc85xx/cpu_init.o (.text)
+    cpu/mpc85xx/cpu.o (.text)
+    cpu/mpc85xx/speed.o (.text)
+    cpu/mpc85xx/spd_sdram.o (.text)
+    common/dlmalloc.o (.text)
+    lib_generic/crc32.o (.text)
+    lib_ppc/extable.o (.text)
+    lib_generic/zlib.o (.text)
+    *(.text)
+    *(.fixup)
+    *(.got1)
+   }
+    _etext = .;
+    PROVIDE (etext = .);
+    .rodata    :
+   {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+    *(.eh_frame)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}