Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm:
  Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board
  arm: jadecpu: Readd MACH_TYPE_JADECPU
  at91: defined mach-types for otc570 board in board config file
  at91: defined mach-types for meesc board in board config file
  mx31pdk: Enable D and I caches
  ehci-mxc: remove incorrect comment
  README: Fix supported i.MX SoC list for CONFIG_MXC_SPI
  mx53: Turn off child clocks before reconfigure perclk_root
  qong: enable support for compressed images
  imx: imx31_phycore.h: fix checkpatch warnings
  vision2: Remove unused get_board_rev function
  mx53smd: Remove unused get_board_rev function
  mx53ard: Remove unused get_board_rev function
  mx53evk: Remove unused get_board_rev function
  mx53evk: Add RTC support
  mx53loco: Remove unused get_board_rev function
  mx53evk: Remove unneeded '1' from mx53evk.h
  OMAP3: mvblx: Initial support for mvBlueLYNX-X
  ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE
  omap3: mem: Move comments next to definitions
  omap3: mem: Clean-up whitespaces
  omap3: mem: Define and use common macros
  Davinci: ea20: added PREBOOT to configuration
  Davinci: ea20: added I2C support
  Davinci: ea20: added video support
  VIDEO: davinci: add framebuffer to da8xx
  ARM: Davinci: added missing registers to hardware.h
  Davinci: ea20: add gpios for LCD backlight control
  Davinci: ea20: add gpio for keeping power on in board_late_init
  Davinci: ea20: Add default U-Boot environment
  Davinci: ea20: Add early init to get early output from console
  Davinci: ea20: Add NAND support
  Davinci: ea20: set GPIOs to hold MII-Phy in reset and set UART0-Switch for console
  Davinci: ea20: set console on UART0
  arm, davinci: add cam_enc_4xx support
  arm926ejs, davinci: add missing spi defines for dm365
  arm926ejs, davinci: add cpuinfo for dm365
  arm, davinci: add lowlevel function for dm365 soc
  arm, davinci: add header files for dm365
  spl, nand: add 4bit HW ecc oob first nand_read_page function
  arm, davinci: add support for new spl framework
  spl: add option for adding post memory test to the SPL framework
  net, davinci_emac: make clock divider in MDIO control register configurable
  arm, usb, davinci: make USBPHY_CTL register configurable
  usb, davinci: add enable_vbus() weak function
  omap3evm: fix errors caused by multiple definitions
  omap3evm: Add (quick) configuration for NAND only
  omap3evm: Add (quick) configuration for MMC/SD only
  omap3evm: move common config options to new file
  omap3evm: Prepare to split configuration
  omap3evm: Reorder related config options
  omap/spl: actually enable the console
  davinci_emac: compilation fix, phy is array now
  omap3evm: Set environment variable 'ethaddr'
  arm, arm926: fix missing symbols in NAND_SPL mode
  arm, davinci: Add function lpsc_syncreset()
  arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILD
  arm/km: portl2 environment address update to P1B
  arm/km: adapt bootcounter evaluation
  arm/km: enable jffs2 cmds
  arm/km: trigger reconfiguration for the Xilinx FPGA
  arm/km: add boardid and hwkey to kernel command line
  ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards
  netspace_v2: enable I2C EEPROM support
  netspace_v2: fix SDRAM configuration
  armada100: define CONFIG_SYS_CACHELINE_SIZE
  pantheon: define CONFIG_SYS_CACHELINE_SIZE
  kirkwood: define CONFIG_SYS_CACHELINE_SIZE
  kirkwood: drop empty asm-offsets.s file
  arm/km/mgcoge3un: enhance "waitforne" feature
  arm/km: add variable waitforne to mgcoge3un
  gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclared
  ARM: dreamplug: fix compilation
  ARM: DockStar: fix compilation
  ARM: netspace_v2: fix warnings
  am335x: Drop board_sysinfo struct
  am335x: Temporarily add MACH_TYPE define
  misc:pmic:samsung Enable PMIC driver at C210 Universal target
  dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 target
  dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI target
  smdkv310: use macro for mmc data read function address
  smdkv310: use spl framework for mmc spl
  SMDKV310: use get_ram_size() to validate dram size
  SMDKV310: Initialize board id using CONFIG_MACH_TYPE
  ORIGEN : use absolute paths and fix tool naming
  ORIGEN : enable device tree support
  MX25: tx25: Fix building due to missing MACH_TYPE
  mx31: Add board support for HALE TT-01
  mx31: add ESD control registers
  mx31: define pins and init for UART2 and CSPI3
  MX35: add support for flea3 board
  MX51: vision2: add MACH_TYPE in config file
  vision2: Remove unused header file
  mx51evk: Remove unused get_board_rev function
  mx51evk: Remove unneeded '1' from mx51evk.h
  I2C: Fix mxc_i2c.c problem on imx31_phycore
  mx35pdk: Add RTC support
  mx51evk: Use GPIO API for configuring the IOMUX
  mx51evk: Add RTC support
  rtc: Make mc13783-rtc driver generic
  qong: remove unneeded IOMUX settings
  qong: Use mx31_set_gpr to setup USBH2 pins
  mx31: Introduce mx31_set_gpr function
  mx31pdk: Add MC13783 PMIC support
  qong: remove unneeded "1" from qong.h
  misc: pmic: fix regression in pmic_fsl.c (SPI)
  mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIME
  MX35: Drop unnecessary prototypes from imx-regs.h
  I2C: added I2C-2 and I2C-3 to MX35
  MX35: factorize common assembly code
  MX35: add reset cause as provided by other i.MX
  MX35: add pins definition for UART3
  MX35: added ESDC structure to imx-regs

45 files changed, 3225 insertions, 130 deletions

diff --git a/board/CarMediaLab/flea3/Makefile b/board/CarMediaLab/flea3/Makefile
new file mode 100644
index 0000000000..f5ad4949d6
--- /dev/null
+++ b/board/CarMediaLab/flea3/Makefile
@@ -0,0 +1,49 @@
+#
+# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
+#
+# (C) Copyright 2008-2009 Freescale Semiconductor, Inc.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	:= flea3.o
+SOBJS	:= lowlevel_init.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/CarMediaLab/flea3/flea3.c b/board/CarMediaLab/flea3/flea3.c
new file mode 100644
index 0000000000..64f4b57f1b
--- /dev/null
+++ b/board/CarMediaLab/flea3/flea3.c
@@ -0,0 +1,289 @@
+/*
+ * Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
+ *
+ * (C) Copyright 2008-2010 Freescale Semiconductor, Inc.
+ *
+ * Copyright (C) 2011, Stefano Babic <sbabic@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx35_pins.h>
+#include <asm/arch/iomux.h>
+#include <i2c.h>
+#include <linux/types.h>
+#include <asm/gpio.h>
+#include <asm/arch/sys_proto.h>
+#include <netdev.h>
+
+#ifndef CONFIG_BOARD_EARLY_INIT_F
+#error "CONFIG_BOARD_EARLY_INIT_F must be set for this board"
+#endif
+
+#define CCM_CCMR_CONFIG		0x003F4208
+
+#define ESDCTL_DDR2_CONFIG	0x007FFC3F
+#define ESDCTL_0x92220000	0x92220000
+#define ESDCTL_0xA2220000	0xA2220000
+#define ESDCTL_0xB2220000	0xB2220000
+#define ESDCTL_0x82228080	0x82228080
+#define ESDCTL_DDR2_EMR2	0x04000000
+#define ESDCTL_DDR2_EMR3	0x06000000
+#define ESDCTL_PRECHARGE	0x00000400
+#define ESDCTL_DDR2_EN_DLL	0x02000400
+#define ESDCTL_DDR2_RESET_DLL	0x00000333
+#define ESDCTL_DDR2_MR		0x00000233
+#define ESDCTL_DDR2_OCD_DEFAULT 0x02000780
+#define ESDCTL_DELAY_LINE5	0x00F49F00
+
+static inline void dram_wait(unsigned int count)
+{
+	volatile unsigned int wait = count;
+
+	while (wait--)
+		;
+}
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1,
+		PHYS_SDRAM_1_SIZE);
+
+	return 0;
+}
+
+static void board_setup_sdram_bank(u32 start_address)
+
+{
+	struct esdc_regs *esdc = (struct esdc_regs *)ESDCTL_BASE_ADDR;
+	u32 *cfg_reg, *ctl_reg;
+	u32 val;
+
+	switch (start_address) {
+	case CSD0_BASE_ADDR:
+		cfg_reg = &esdc->esdcfg0;
+		ctl_reg = &esdc->esdctl0;
+		break;
+	case CSD1_BASE_ADDR:
+		cfg_reg = &esdc->esdcfg1;
+		ctl_reg = &esdc->esdctl1;
+		break;
+	default:
+		return;
+	}
+
+	/* Initialize MISC register for DDR2 */
+	val = ESDC_MISC_RST | ESDC_MISC_MDDR_EN | ESDC_MISC_MDDR_DL_RST |
+		ESDC_MISC_DDR_EN | ESDC_MISC_DDR2_EN;
+	writel(val, &esdc->esdmisc);
+	val &= ~(ESDC_MISC_RST | ESDC_MISC_MDDR_DL_RST);
+	writel(val, &esdc->esdmisc);
+
+	/*
+	 * according to DDR2 specs, wait a while before
+	 * the PRECHARGE_ALL command
+	 */
+	dram_wait(0x20000);
+
+	/* Load DDR2 config and timing */
+	writel(ESDCTL_DDR2_CONFIG, cfg_reg);
+
+	/* Precharge ALL */
+	writel(ESDCTL_0x92220000,
+		ctl_reg);
+	writel(0xda, start_address + ESDCTL_PRECHARGE);
+
+	/* Load mode */
+	writel(ESDCTL_0xB2220000,
+		ctl_reg);
+	writeb(0xda, start_address + ESDCTL_DDR2_EMR2); /* EMRS2 */
+	writeb(0xda, start_address + ESDCTL_DDR2_EMR3); /* EMRS3 */
+	writeb(0xda, start_address + ESDCTL_DDR2_EN_DLL); /* Enable DLL */
+	writeb(0xda, start_address + ESDCTL_DDR2_RESET_DLL); /* Reset DLL */
+
+	/* Precharge ALL */
+	writel(ESDCTL_0x92220000,
+		ctl_reg);
+	writel(0xda, start_address + ESDCTL_PRECHARGE);
+
+	/* Set mode auto refresh : at least two refresh are required */
+	writel(ESDCTL_0xA2220000,
+		ctl_reg);
+	writel(0xda, start_address);
+	writel(0xda, start_address);
+
+	writel(ESDCTL_0xB2220000,
+		ctl_reg);
+	writeb(0xda, start_address + ESDCTL_DDR2_MR);
+	writeb(0xda, start_address + ESDCTL_DDR2_OCD_DEFAULT);
+
+	/* OCD mode exit */
+	writeb(0xda, start_address + ESDCTL_DDR2_EN_DLL); /* Enable DLL */
+
+	/* Set normal mode */
+	writel(ESDCTL_0x82228080,
+		ctl_reg);
+
+	dram_wait(0x20000);
+
+	/* Do not set delay lines, only for MDDR */
+}
+
+static void board_setup_sdram(void)
+{
+	struct esdc_regs *esdc = (struct esdc_regs *)ESDCTL_BASE_ADDR;
+
+	/* Initialize with default values both CSD0/1 */
+	writel(0x2000, &esdc->esdctl0);
+	writel(0x2000, &esdc->esdctl1);
+
+	board_setup_sdram_bank(CSD1_BASE_ADDR);
+}
+
+static void setup_iomux_uart3(void)
+{
+	mxc_request_iomux(MX35_PIN_RTS2_UART3_RXD_MUX, MUX_CONFIG_ALT7);
+	mxc_request_iomux(MX35_PIN_CTS2_UART3_TXD_MUX, MUX_CONFIG_ALT7);
+}
+
+static void setup_iomux_i2c(void)
+{
+	int pad;
+
+	mxc_request_iomux(MX35_PIN_I2C1_CLK, MUX_CONFIG_SION);
+	mxc_request_iomux(MX35_PIN_I2C1_DAT, MUX_CONFIG_SION);
+
+	pad = (PAD_CTL_HYS_SCHMITZ | PAD_CTL_PKE_ENABLE \
+			| PAD_CTL_PUE_PUD | PAD_CTL_ODE_OpenDrain);
+
+	mxc_iomux_set_pad(MX35_PIN_I2C1_CLK, pad);
+	mxc_iomux_set_pad(MX35_PIN_I2C1_DAT, pad);
+
+	mxc_request_iomux(MX35_PIN_TX3_RX2, MUX_CONFIG_ALT1);
+	mxc_request_iomux(MX35_PIN_TX2_RX3, MUX_CONFIG_ALT1);
+
+	mxc_iomux_set_pad(MX35_PIN_TX3_RX2, pad);
+	mxc_iomux_set_pad(MX35_PIN_TX2_RX3, pad);
+}
+
+
+static void setup_iomux_spi(void)
+{
+	mxc_request_iomux(MX35_PIN_CSPI1_MOSI, MUX_CONFIG_SION);
+	mxc_request_iomux(MX35_PIN_CSPI1_MISO, MUX_CONFIG_SION);
+	mxc_request_iomux(MX35_PIN_CSPI1_SS0, MUX_CONFIG_SION);
+	mxc_request_iomux(MX35_PIN_CSPI1_SS1, MUX_CONFIG_SION);
+	mxc_request_iomux(MX35_PIN_CSPI1_SCLK, MUX_CONFIG_SION);
+}
+
+static void setup_iomux_fec(void)
+{
+	/* setup pins for FEC */
+	mxc_request_iomux(MX35_PIN_FEC_TX_CLK, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_RX_CLK, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_RX_DV, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_COL, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_RDATA0, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_TDATA0, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_TX_EN, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_MDC, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_MDIO, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_TX_ERR, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_RX_ERR, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_CRS, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_RDATA1, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_TDATA1, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_RDATA2, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_TDATA2, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_RDATA3, MUX_CONFIG_FUNC);
+	mxc_request_iomux(MX35_PIN_FEC_TDATA3, MUX_CONFIG_FUNC);
+
+}
+
+int board_early_init_f(void)
+{
+	struct ccm_regs *ccm =
+		(struct ccm_regs *)IMX_CCM_BASE;
+
+	/* setup GPIO3_1 to set HighVCore signal */
+	mxc_request_iomux(MX35_PIN_ATA_DATA1, MUX_CONFIG_ALT5);
+	gpio_direction_output(65, 1);
+
+	/* initialize PLL and clock configuration */
+	writel(CCM_CCMR_CONFIG, &ccm->ccmr);
+
+	writel(CCM_MPLL_532_HZ, &ccm->mpctl);
+	writel(CCM_PPLL_300_HZ, &ccm->ppctl);
+
+	/* Set the core to run at 532 Mhz */
+	writel(0x00001000, &ccm->pdr0);
+
+	/* Set-up RAM */
+	board_setup_sdram();
+
+	/* enable clocks */
+	writel(readl(&ccm->cgr0) |
+		MXC_CCM_CGR0_EMI_MASK |
+		MXC_CCM_CGR0_EDI0_MASK |
+		MXC_CCM_CGR0_EPIT1_MASK,
+		&ccm->cgr0);
+
+	writel(readl(&ccm->cgr1) |
+		MXC_CCM_CGR1_FEC_MASK |
+		MXC_CCM_CGR1_GPIO1_MASK |
+		MXC_CCM_CGR1_GPIO2_MASK |
+		MXC_CCM_CGR1_GPIO3_MASK |
+		MXC_CCM_CGR1_I2C1_MASK |
+		MXC_CCM_CGR1_I2C2_MASK |
+		MXC_CCM_CGR1_I2C3_MASK,
+		&ccm->cgr1);
+
+	/* Set-up NAND */
+	__raw_writel(readl(&ccm->rcsr) | MXC_CCM_RCSR_NFC_FMS, &ccm->rcsr);
+
+	/* Set pinmux for the required peripherals */
+	setup_iomux_uart3();
+	setup_iomux_i2c();
+	setup_iomux_fec();
+	setup_iomux_spi();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+	return 0;
+}
+
+u32 get_board_rev(void)
+{
+	int rev = 0;
+
+	return (get_cpu_rev() & ~(0xF << 8)) | (rev & 0xF) << 8;
+}
diff --git a/board/CarMediaLab/flea3/lowlevel_init.S b/board/CarMediaLab/flea3/lowlevel_init.S
new file mode 100644
index 0000000000..2f42fc97af
--- /dev/null
+++ b/board/CarMediaLab/flea3/lowlevel_init.S
@@ -0,0 +1,79 @@
+/*
+ * Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
+ *
+ * (C) Copyright 2008-2010 Freescale Semiconductor, Inc.
+ *
+ * Copyright (C) 2011, Stefano Babic <sbabic@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <asm-offsets.h>
+#include <asm/arch/imx-regs.h>
+#include <generated/asm-offsets.h>
+
+/*
+ * Configuration for the flea3 board.
+ * These defines are used by the included macros and must
+ * be defined first
+ */
+#define AIPS_MPR_CONFIG		0x77777777
+#define AIPS_OPACR_CONFIG	0x00000000
+
+/* MPR - priority is M4 > M2 > M3 > M5 > M0 > M1 */
+#define MAX_MPR_CONFIG		0x00302154
+
+/* SGPCR - always park on last master */
+#define MAX_SGPCR_CONFIG	0x00000010
+
+/* MGPCR - restore default values */
+#define MAX_MGPCR_CONFIG	0x00000000
+
+/*
+ * M3IF Control Register (M3IFCTL)
+ * MRRP[0] = L2CC0 not on priority list (0 << 0) = 0x00000000
+ * MRRP[1] = L2CC1 not on priority list (0 << 0) = 0x00000000
+ * MRRP[2] = MBX not on priority list (0 << 0)   = 0x00000000
+ * MRRP[3] = MAX1 not on priority list (0 << 0)  = 0x00000000
+ * MRRP[4] = SDMA not on priority list (0 << 0)  = 0x00000000
+ * MRRP[5] = MPEG4 not on priority list (0 << 0) = 0x00000000
+ * MRRP[6] = IPU1 on priority list (1 << 6)      = 0x00000040
+ * MRRP[7] = IPU2 not on priority list (0 << 0)  = 0x00000000
+ *                                               ------------
+ *                                                 0x00000040
+ */
+#define M3IF_CONFIG		0x00000040
+
+#define CCM_PDR0_CONFIG		0x00801000
+
+/*
+ * includes MX35 utility macros
+ */
+#include <asm/arch/lowlevel_macro.S>
+
+.globl lowlevel_init
+lowlevel_init:
+
+	core_init
+
+	init_aips
+
+	init_max
+
+	init_m3if
+
+	mov pc, lr
diff --git a/board/LaCie/netspace_v2/kwbimage-is2.cfg b/board/LaCie/netspace_v2/kwbimage-is2.cfg
new file mode 100644
index 0000000000..590720af8c
--- /dev/null
+++ b/board/LaCie/netspace_v2/kwbimage-is2.cfg
@@ -0,0 +1,162 @@
+#
+# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+#
+# Based on Kirkwood support:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM	spi	# Boot from SPI flash
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1B1B1B9B
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000618	# DDR Configuration register
+# bit13-0:  0xa00 (2560 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x35143000	# DDR Controller Control Low
+# bit 4:    0=addr/cmd in smame cycle
+# bit 5:    0=clk is driven during self refresh, we don't care for APX
+# bit 6:    0=use recommended falling edge of clk for addr/cmd
+# bit14:    0=input buffer always powered up
+# bit18:    1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31:    0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x11012228	# DDR Timing (Low) (active cycles value +1)
+# bit7-4:   TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20:    TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000A19	#  DDR Timing (High)
+# bit6-0:   TRFC
+# bit8-7:   TR2R
+# bit10-9:  TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x00000008	#  DDR Address Control
+# bit1-0:   00, Cs0width=x8
+# bit3-2:   10, Cs0size=512Mb
+# bit5-4:   00, Cs2width=nonexistent
+# bit7-6:   00, Cs1size =nonexistent
+# bit9-8:   00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16:    0,  Cs0AddrSel
+# bit17:    0,  Cs1AddrSel
+# bit18:    0,  Cs2AddrSel
+# bit19:    0,  Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
+# bit0:    0,  OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000	#  DDR Operation
+# bit3-0:   0x0, DDR cmd
+# bit31-4:  0 required
+
+DATA 0xFFD0141C 0x00000632	#  DDR Mode
+# bit2-0:   2, BurstLen=2 required
+# bit3:     0, BurstType=0 required
+# bit6-4:   4, CL=5
+# bit7:     0, TestMode=0 normal
+# bit8:     0, DLL reset=0 normal
+# bit11-9:  6, auto-precharge write recovery ????????????
+# bit12:    0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000004	#  DDR Extended Mode
+# bit0:    0,  DDR DLL enabled
+# bit1:    1,  DDR drive strenght reduced
+# bit2:    1,  DDR ODT control lsd enabled
+# bit5-3:  000, required
+# bit6:    1,  DDR ODT control msb, enabled
+# bit9-7:  000, required
+# bit10:   0,  differential DQS enabled
+# bit11:   0, required
+# bit12:   0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F07F	#  DDR Controller Control High
+# bit2-0:  111, required
+# bit3  :  1  , MBUS Burst Chop disabled
+# bit6-4:  111, required
+# bit7  :  1  , D2P Latency enabled
+# bit8  :  1  , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9  :  0  , no half clock cycle addition to dataout
+# bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0    required
+
+DATA 0xFFD01428 0x00085520	# DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552	# DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x07FFFFF1	# CS[0]n Size
+# bit0:    1,  Window enabled
+# bit1:    0,  Write Protect disabled
+# bit3-2:  00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x07, Size (i.e. 128MB)
+
+DATA 0xFFD0150C 0x00000000	# CS[1]n Size, window disabled
+DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00010000	#  DDR ODT Control (Low)
+# bit3-0:  1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
+# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
+
+DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
+# bit1-0:  00, ODT0 controlled by ODT Control (low) register above
+# bit3-2:  01, ODT1 active NEVER!
+# bit31-4: zero, required
+
+DATA 0xFFD0149C 0x0000E40F	# CPU ODT Control
+# bit3-0:  1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
+# bit7-4:  1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
+# bit11-10:1, DQ_ODTSel. ODT select turned on
+
+DATA 0xFFD01480 0x00000001	# DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/board/LaCie/netspace_v2/kwbimage.cfg b/board/LaCie/netspace_v2/kwbimage.cfg
index 361feeb6fa..7e53649121 100644
--- a/board/LaCie/netspace_v2/kwbimage.cfg
+++ b/board/LaCie/netspace_v2/kwbimage.cfg
@@ -69,8 +69,8 @@ DATA 0xFFD0140C 0x00000A19	#  DDR Timing (High)
 # bit12-11: TW2W
 # bit31-13: zero required
 
-DATA 0xFFD01410 0x0000CCCC	#  DDR Address Control
-# bit1-0:   01, Cs0width=x16
+DATA 0xFFD01410 0x0000000C	#  DDR Address Control
+# bit1-0:   00, Cs0width=x8
 # bit3-2:   11, Cs0size=1Gb
 # bit5-4:   00, Cs2width=nonexistent
 # bit7-6:   00, Cs1size =nonexistent
diff --git a/board/LaCie/netspace_v2/netspace_v2.c b/board/LaCie/netspace_v2/netspace_v2.c
index 3bb83f359e..7c4b15ec47 100644
--- a/board/LaCie/netspace_v2/netspace_v2.c
+++ b/board/LaCie/netspace_v2/netspace_v2.c
@@ -24,6 +24,7 @@
 #include <miiphy.h>
 #include <netdev.h>
 #include <command.h>
+#include <asm/arch/cpu.h>
 #include <asm/arch/kirkwood.h>
 #include <asm/arch/mpp.h>
 #include <asm/arch/gpio.h>
diff --git a/board/Marvell/dreamplug/dreamplug.c b/board/Marvell/dreamplug/dreamplug.c
index 13b401361c..31b73c98b0 100644
--- a/board/Marvell/dreamplug/dreamplug.c
+++ b/board/Marvell/dreamplug/dreamplug.c
@@ -27,6 +27,7 @@
 
 #include <common.h>
 #include <miiphy.h>
+#include <asm/arch/cpu.h>
 #include <asm/arch/kirkwood.h>
 #include <asm/arch/mpp.h>
 #include "dreamplug.h"
diff --git a/board/Seagate/dockstar/dockstar.c b/board/Seagate/dockstar/dockstar.c
index cab3a83947..a1de0dc4df 100644
--- a/board/Seagate/dockstar/dockstar.c
+++ b/board/Seagate/dockstar/dockstar.c
@@ -29,6 +29,8 @@
 #include <miiphy.h>
 #include <asm/arch/kirkwood.h>
 #include <asm/arch/mpp.h>
+#include <asm/arch/cpu.h>
+#include <asm/io.h>
 #include "dockstar.h"
 
 DECLARE_GLOBAL_DATA_PTR;
diff --git a/board/ait/cam_enc_4xx/Makefile b/board/ait/cam_enc_4xx/Makefile
new file mode 100644
index 0000000000..2b221246ae
--- /dev/null
+++ b/board/ait/cam_enc_4xx/Makefile
@@ -0,0 +1,46 @@
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	:= $(BOARD).o
+SOBJS	:=
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+# This is for $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/ait/cam_enc_4xx/cam_enc_4xx.c b/board/ait/cam_enc_4xx/cam_enc_4xx.c
new file mode 100644
index 0000000000..1351358298
--- /dev/null
+++ b/board/ait/cam_enc_4xx/cam_enc_4xx.c
@@ -0,0 +1,446 @@
+/*
+ * Copyright (C) 2009 Texas Instruments Incorporated
+ *
+ * Copyright (C) 2011
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <common.h>
+#include <linux/mtd/nand.h>
+#include <nand.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/nand_defs.h>
+#include <asm/arch/davinci_misc.h>
+#ifdef CONFIG_DAVINCI_MMC
+#include <mmc.h>
+#include <asm/arch/sdmmc_defs.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifndef CONFIG_SPL_BUILD
+int dram_init(void)
+{
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size(
+			(void *)CONFIG_SYS_SDRAM_BASE,
+			CONFIG_MAX_RAM_BANK_SIZE);
+	return 0;
+}
+
+void dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
+static struct davinci_timer *timer =
+	(struct davinci_timer *)DAVINCI_TIMER3_BASE;
+
+static unsigned long get_timer_val(void)
+{
+	unsigned long now = readl(&timer->tim34);
+
+	return now;
+}
+
+static void stop_timer(void)
+{
+	writel(0x0, &timer->tcr);
+	return;
+}
+
+int checkboard(void)
+{
+	printf("Board: AIT CAM ENC 4XX\n");
+	return 0;
+}
+
+int board_init(void)
+{
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+	return 0;
+}
+
+#ifdef CONFIG_DRIVER_TI_EMAC
+int board_eth_init(bd_t *bis)
+{
+	davinci_emac_initialize();
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_NAND_DAVINCI
+static int
+davinci_std_read_page_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
+				   uint8_t *buf, int page)
+{
+	struct nand_chip *this = mtd->priv;
+	int i, eccsize = chip->ecc.size;
+	int eccbytes = chip->ecc.bytes;
+	int eccsteps = chip->ecc.steps;
+	uint8_t *p = buf;
+	uint8_t *oob = chip->oob_poi;
+
+	chip->cmdfunc(mtd, NAND_CMD_READOOB, 0x0, page & this->pagemask);
+
+	chip->read_buf(mtd, oob, mtd->oobsize);
+
+	chip->cmdfunc(mtd, NAND_CMD_READ0, 0x0, page & this->pagemask);
+
+
+	for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+		int stat;
+
+		chip->ecc.hwctl(mtd, NAND_ECC_READ);
+		chip->read_buf(mtd, p, eccsize);
+		chip->ecc.hwctl(mtd, NAND_ECC_READSYN);
+
+		if (chip->ecc.prepad)
+			oob += chip->ecc.prepad;
+
+		stat = chip->ecc.correct(mtd, p, oob, NULL);
+
+		if (stat == -1)
+			mtd->ecc_stats.failed++;
+		else
+			mtd->ecc_stats.corrected += stat;
+
+		oob += eccbytes;
+
+		if (chip->ecc.postpad)
+			oob += chip->ecc.postpad;
+	}
+
+	/* Calculate remaining oob bytes */
+	i = mtd->oobsize - (oob - chip->oob_poi);
+	if (i)
+		chip->read_buf(mtd, oob, i);
+
+	return 0;
+}
+
+static void davinci_std_write_page_syndrome(struct mtd_info *mtd,
+				    struct nand_chip *chip, const uint8_t *buf)
+{
+	unsigned char davinci_ecc_buf[NAND_MAX_OOBSIZE];
+	struct nand_chip *this = mtd->priv;
+	int i, eccsize = chip->ecc.size;
+	int eccbytes = chip->ecc.bytes;
+	int eccsteps = chip->ecc.steps;
+	int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad;
+	int offset = 0;
+	const uint8_t *p = buf;
+	uint8_t *oob = chip->oob_poi;
+
+	for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+		chip->ecc.hwctl(mtd, NAND_ECC_WRITE);
+		chip->write_buf(mtd, p, eccsize);
+
+		/* Calculate ECC without prepad */
+		chip->ecc.calculate(mtd, p, oob + chip->ecc.prepad);
+
+		if (chip->ecc.prepad) {
+			offset = (chip->ecc.steps - eccsteps) * chunk;
+			memcpy(&davinci_ecc_buf[offset], oob, chip->ecc.prepad);
+			oob += chip->ecc.prepad;
+		}
+
+		offset = ((chip->ecc.steps - eccsteps) * chunk) +
+				chip->ecc.prepad;
+		memcpy(&davinci_ecc_buf[offset], oob, eccbytes);
+		oob += eccbytes;
+
+		if (chip->ecc.postpad) {
+			offset = ((chip->ecc.steps - eccsteps) * chunk) +
+					chip->ecc.prepad + eccbytes;
+			memcpy(&davinci_ecc_buf[offset], oob,
+				chip->ecc.postpad);
+			oob += chip->ecc.postpad;
+		}
+	}
+
+	/*
+	 * Write the sparebytes into the page once
+	 * all eccsteps have been covered
+	 */
+	for (i = 0; i < mtd->oobsize; i++)
+		writeb(davinci_ecc_buf[i], this->IO_ADDR_W);
+
+	/* Calculate remaining oob bytes */
+	i = mtd->oobsize - (oob - chip->oob_poi);
+	if (i)
+		chip->write_buf(mtd, oob, i);
+}
+
+static int davinci_std_write_oob_syndrome(struct mtd_info *mtd,
+				   struct nand_chip *chip, int page)
+{
+	int pos, status = 0;
+	const uint8_t *bufpoi = chip->oob_poi;
+
+	pos = mtd->writesize;
+
+	chip->cmdfunc(mtd, NAND_CMD_SEQIN, pos, page);
+
+	chip->write_buf(mtd, bufpoi, mtd->oobsize);
+
+	chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
+	status = chip->waitfunc(mtd, chip);
+
+	return status & NAND_STATUS_FAIL ? -1 : 0;
+}
+
+static int davinci_std_read_oob_syndrome(struct mtd_info *mtd,
+	struct nand_chip *chip, int page, int sndcmd)
+{
+	struct nand_chip *this = mtd->priv;
+	uint8_t *buf = chip->oob_poi;
+	uint8_t *bufpoi = buf;
+
+	chip->cmdfunc(mtd, NAND_CMD_READOOB, 0x0, page & this->pagemask);
+
+	chip->read_buf(mtd, bufpoi, mtd->oobsize);
+
+	return 1;
+}
+
+static void nand_dm365evm_select_chip(struct mtd_info *mtd, int chip)
+{
+	struct nand_chip	*this = mtd->priv;
+	unsigned long		wbase = (unsigned long) this->IO_ADDR_W;
+	unsigned long		rbase = (unsigned long) this->IO_ADDR_R;
+
+	if (chip == 1) {
+		__set_bit(14, &wbase);
+		__set_bit(14, &rbase);
+	} else {
+		__clear_bit(14, &wbase);
+		__clear_bit(14, &rbase);
+	}
+	this->IO_ADDR_W = (void *)wbase;
+	this->IO_ADDR_R = (void *)rbase;
+}
+
+int board_nand_init(struct nand_chip *nand)
+{
+	davinci_nand_init(nand);
+	nand->select_chip = nand_dm365evm_select_chip;
+
+	return 0;
+}
+
+struct nand_ecc_ctrl org_ecc;
+static int notsaved = 1;
+
+static int nand_switch_hw_func(int mode)
+{
+	struct nand_chip *nand;
+	struct mtd_info *mtd;
+
+	if (nand_curr_device < 0 ||
+	    nand_curr_device >= CONFIG_SYS_MAX_NAND_DEVICE ||
+	    !nand_info[nand_curr_device].name) {
+		printf("Error: Can't switch hw functions," \
+			" no devices available\n");
+		return -1;
+	}
+
+	mtd = &nand_info[nand_curr_device];
+	nand = mtd->priv;
+
+	if (mode == 0) {
+		printf("switching to uboot hw functions.\n");
+		memcpy(&nand->ecc, &org_ecc, sizeof(struct nand_ecc_ctrl));
+	} else {
+		/* RBL */
+		printf("switching to RBL hw functions.\n");
+		if (notsaved == 1) {
+			memcpy(&org_ecc, &nand->ecc,
+				sizeof(struct nand_ecc_ctrl));
+			notsaved = 0;
+		}
+		nand->ecc.mode = NAND_ECC_HW_SYNDROME;
+		nand->ecc.prepad = 6;
+		nand->ecc.read_page = davinci_std_read_page_syndrome;
+		nand->ecc.write_page = davinci_std_write_page_syndrome;
+		nand->ecc.read_oob = davinci_std_read_oob_syndrome;
+		nand->ecc.write_oob = davinci_std_write_oob_syndrome;
+	}
+	return mode;
+}
+
+static int hwmode;
+
+static int do_switch_ecc(cmd_tbl_t *cmdtp, int flag, int argc,
+		char *const argv[])
+{
+	if (argc != 2)
+		goto usage;
+	if (strncmp(argv[1], "rbl", 2) == 0)
+		hwmode = nand_switch_hw_func(1);
+	else if (strncmp(argv[1], "uboot", 2) == 0)
+		hwmode = nand_switch_hw_func(0);
+	else
+		goto usage;
+
+	return 0;
+
+usage:
+	printf("Usage: nandrbl %s\n", cmdtp->usage);
+	return 1;
+}
+
+U_BOOT_CMD(
+	nandrbl, 2, 1,	do_switch_ecc,
+	"switch between rbl/uboot NAND ECC calculation algorithm",
+	"[rbl/uboot] - Switch between rbl/uboot NAND ECC algorithm"
+);
+
+
+#endif /* #ifdef CONFIG_NAND_DAVINCI */
+
+#ifdef CONFIG_DAVINCI_MMC
+static struct davinci_mmc mmc_sd0 = {
+	.reg_base	= (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE,
+	.input_clk	= 121500000,
+	.host_caps	= MMC_MODE_4BIT,
+	.voltages	= MMC_VDD_32_33 | MMC_VDD_33_34,
+	.version	= MMC_CTLR_VERSION_2,
+};
+
+int board_mmc_init(bd_t *bis)
+{
+	int err;
+
+	/* Add slot-0 to mmc subsystem */
+	err = davinci_mmc_init(bis, &mmc_sd0);
+
+	return err;
+}
+#endif
+
+int board_late_init(void)
+{
+	struct davinci_gpio *gpio = davinci_gpio_bank45;
+
+	/* 24MHz InputClock / 15 prediv -> 1.6 MHz timer running */
+	while (get_timer_val() < 0x186a00)
+		;
+
+	/* 1 sec reached -> stop timer, clear all LED */
+	stop_timer();
+	clrbits_le32(&gpio->out_data, CONFIG_CAM_ENC_LED_MASK);
+	return 0;
+}
+
+void reset_phy(void)
+{
+	char *name = "GENERIC @ 0x00";
+
+	/* reset the phy */
+	miiphy_reset(name, 0x0);
+}
+
+#else /* #ifndef CONFIG_SPL_BUILD */
+static void cam_enc_4xx_set_all_led(void)
+{
+	struct davinci_gpio *gpio = davinci_gpio_bank45;
+
+	setbits_le32(&gpio->out_data, CONFIG_CAM_ENC_LED_MASK);
+}
+
+/*
+ * TIMER 0 is used for tick
+ */
+static struct davinci_timer *timer =
+	(struct davinci_timer *)DAVINCI_TIMER3_BASE;
+
+#define TIMER_LOAD_VAL	0xffffffff
+#define TIM_CLK_DIV	16
+
+static int cam_enc_4xx_timer_init(void)
+{
+	/* We are using timer34 in unchained 32-bit mode, full speed */
+	writel(0x0, &timer->tcr);
+	writel(0x0, &timer->tgcr);
+	writel(0x06 | ((TIM_CLK_DIV - 1) << 8), &timer->tgcr);
+	writel(0x0, &timer->tim34);
+	writel(TIMER_LOAD_VAL, &timer->prd34);
+	writel(2 << 22, &timer->tcr);
+	return 0;
+}
+
+void board_gpio_init(void)
+{
+	struct davinci_gpio *gpio;
+
+	cam_enc_4xx_set_all_led();
+	cam_enc_4xx_timer_init();
+	gpio = davinci_gpio_bank01;
+	clrbits_le32(&gpio->dir, ~0xfdfffffe);
+	/* clear LED D14 = GPIO25 */
+	clrbits_le32(&gpio->out_data, 0x02000000);
+	gpio = davinci_gpio_bank23;
+	clrbits_le32(&gpio->dir, ~0x5ff0afef);
+	/* set GPIO61 to 1 -> intern UART0 as Console */
+	setbits_le32(&gpio->out_data, 0x20000000);
+	/*
+	 * PHY out of reset GIO 50 = 1
+	 * NAND WP off GIO 51 = 1
+	 */
+	setbits_le32(&gpio->out_data, 0x000c0004);
+	gpio = davinci_gpio_bank45;
+	clrbits_le32(&gpio->dir, ~(0xdb2fffff) | CONFIG_CAM_ENC_LED_MASK);
+	/*
+	 * clear LED:
+	 * D17 = GPIO86
+	 * D11 = GPIO87
+	 * GPIO88
+	 * GPIO89
+	 * D13 = GPIO90
+	 * GPIO91
+	 */
+	clrbits_le32(&gpio->out_data, CONFIG_CAM_ENC_LED_MASK);
+	gpio = davinci_gpio_bank67;
+	clrbits_le32(&gpio->dir, ~0x000007ff);
+}
+
+/*
+ * functions for the post memory test.
+ */
+int arch_memory_test_prepare(u32 *vstart, u32 *size, phys_addr_t *phys_offset)
+{
+	*vstart = CONFIG_SYS_SDRAM_BASE;
+	*size = PHYS_SDRAM_1_SIZE;
+	*phys_offset = 0;
+	return 0;
+}
+
+void arch_memory_failure_handle(void)
+{
+	cam_enc_4xx_set_all_led();
+	puts("mem failure\n");
+	while (1)
+		;
+}
+#endif
diff --git a/board/ait/cam_enc_4xx/config.mk b/board/ait/cam_enc_4xx/config.mk
new file mode 100644
index 0000000000..b1f9b6c221
--- /dev/null
+++ b/board/ait/cam_enc_4xx/config.mk
@@ -0,0 +1,15 @@
+#
+# 	AIT cam_enc_4xx board
+#	cam_enc_4xx board has 1 bank of 256 MB DDR RAM
+#	Physical Address: 8000'0000 to 9000'0000
+#
+# Linux Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+#
+
+#Provide at least 16MB spacing between us and the Linux Kernel image
+PAD_TO	:= 12320
+UBL_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/ublimage.cfg
+ifndef CONFIG_SPL_BUILD
+ALL-y += $(obj)u-boot.ubl
+endif
diff --git a/board/ait/cam_enc_4xx/u-boot-spl.lds b/board/ait/cam_enc_4xx/u-boot-spl.lds
new file mode 100644
index 0000000000..6f6e065a9f
--- /dev/null
+++ b/board/ait/cam_enc_4xx/u-boot-spl.lds
@@ -0,0 +1,73 @@
+/*
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
+ *
+ * (C) Copyright 2008
+ * Guennadi Liakhovetki, DENX Software Engineering, <lg@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+MEMORY { .sram : ORIGIN = CONFIG_SPL_TEXT_BASE,\
+		LENGTH = CONFIG_SPL_MAX_SIZE }
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text      :
+	{
+	__start = .;
+	  arch/arm/cpu/arm926ejs/start.o	(.text)
+	  *(.text*)
+	} >.sram
+
+	. = ALIGN(4);
+	.rodata : { *(SORT_BY_ALIGNMENT(.rodata*)) } >.sram
+
+	. = ALIGN(4);
+	.data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram
+	. = ALIGN(4);
+	.rel.dyn : {
+		__rel_dyn_start = .;
+		*(.rel*)
+		__rel_dyn_end = .;
+	} >.sram
+
+	.dynsym : {
+		__dynsym_start = .;
+		*(.dynsym)
+	} >.sram
+
+	.bss :
+	{
+		. = ALIGN(4);
+		__bss_start = .;
+		*(.bss*)
+		. = ALIGN(4);
+		__bss_end__ = .;
+	} >.sram
+
+	__image_copy_end = .;
+	_end = .;
+}
diff --git a/board/ait/cam_enc_4xx/ublimage.cfg b/board/ait/cam_enc_4xx/ublimage.cfg
new file mode 100644
index 0000000000..95182cab00
--- /dev/null
+++ b/board/ait/cam_enc_4xx/ublimage.cfg
@@ -0,0 +1,48 @@
+#
+# (C Copyright 2011
+# Heiko Schocher DENX Software Engineering hs@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not write to the Free Software
+# Foundation Inc. 51 Franklin Street Fifth Floor Boston,
+# MA 02110-1301 USA
+#
+# Refer doc/README.ublimage for more details about how-to configure
+# and create ublimage boot image
+#
+# The syntax is taken as close as possible with the kwbimage
+
+# UBL special mode : one of
+# safe (the board has no nand neither onenand)
+MODE	safe
+
+# Entry point address for the user bootloader (absolute address)
+# nand spl TEXT_BASE = 0x20 !!
+ENTRY	0x00000020
+
+# Number of pages (size of user bootloader in number of pages)
+# @ nand spl 6 pages
+PAGES	6
+
+# Block number where user bootloader is present
+# RBL starts always with block 1
+START_BLOCK	5
+
+# Page number where user bootloader is present
+# Page 0 is always UBL header
+START_PAGE	0
+
+LD_ADDR		0x20
diff --git a/board/comelit/dig297/dig297.c b/board/comelit/dig297/dig297.c
index c81ce58b62..65482813d2 100644
--- a/board/comelit/dig297/dig297.c
+++ b/board/comelit/dig297/dig297.c
@@ -91,8 +91,6 @@ static const u32 gpmc_lan_config[] = {
 int board_init(void)
 {
 	gpmc_init();		/* in SRAM or SDRAM, finish GPMC */
-	/* board id for Linux */
-	gd->bd->bi_arch_number = MACH_TYPE_OMAP3_CPS;
 	/* boot param addr */
 	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
 
diff --git a/board/davedenx/qong/qong.c b/board/davedenx/qong/qong.c
index 5b2830ce49..665aedf0b5 100644
--- a/board/davedenx/qong/qong.c
+++ b/board/davedenx/qong/qong.c
@@ -120,12 +120,6 @@ int board_early_init_f(void)
 	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_STP, MUX_CTL_FUNC));
 	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DATA0, MUX_CTL_FUNC));
 	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DATA1, MUX_CTL_FUNC));
-	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_STXD3, MUX_CTL_FUNC));
-	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SRXD3, MUX_CTL_FUNC));
-	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SCK3, MUX_CTL_FUNC));
-	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SFS3, MUX_CTL_FUNC));
-	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_STXD6, MUX_CTL_FUNC));
-	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SRXD6, MUX_CTL_FUNC));
 
 #define H2_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
 			PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
@@ -143,7 +137,7 @@ int board_early_init_f(void)
 	mx31_set_pad(MX31_PIN_SRXD3, H2_PAD_CFG);	/* USBH2_DATA6 */
 	mx31_set_pad(MX31_PIN_STXD3, H2_PAD_CFG);	/* USBH2_DATA7 */
 
-	writel(readl((IOMUXC_BASE + 0x8)) | (1 << 11), IOMUXC_BASE + 0x8);
+	mx31_set_gpr(MUX_PGP_UH2, 1);
 
 	return 0;
 
diff --git a/board/davinci/common/misc.c b/board/davinci/common/misc.c
index 89ae1115d6..5aa7605f00 100644
--- a/board/davinci/common/misc.c
+++ b/board/davinci/common/misc.c
@@ -33,7 +33,7 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#ifndef CONFIG_PRELOADER
+#ifndef CONFIG_SPL_BUILD
 int dram_init(void)
 {
 	/* dram_init must store complete ramsize in gd->ram_size */
diff --git a/board/davinci/ea20/ea20.c b/board/davinci/ea20/ea20.c
index 9d0f71bc55..720a3607a7 100644
--- a/board/davinci/ea20/ea20.c
+++ b/board/davinci/ea20/ea20.c
@@ -35,11 +35,28 @@
 #include <asm/arch/emac_defs.h>
 #include <asm/io.h>
 #include <asm/arch/davinci_misc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/da8xx-fb.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
 #define pinmux(x)	(&davinci_syscfg_regs->pinmux[x])
 
+static const struct da8xx_panel lcd_panel = {
+	/* Casio COM57H531x */
+	.name = "Casio_COM57H531x",
+	.width = 640,
+	.height = 480,
+	.hfp = 12,
+	.hbp = 144,
+	.hsw = 30,
+	.vfp = 10,
+	.vbp = 35,
+	.vsw = 3,
+	.pxl_clk = 25000000,
+	.invert_pxl_clk = 0,
+};
+
 /* SPI0 pin muxer settings */
 static const struct pinmux_config spi1_pins[] = {
 	{ pinmux(5), 1, 1 },
@@ -48,12 +65,18 @@ static const struct pinmux_config spi1_pins[] = {
 	{ pinmux(5), 1, 5 }
 };
 
-/* UART pin muxer settings */
+/* I2C pin muxer settings */
+static const struct pinmux_config i2c_pins[] = {
+	{ pinmux(4), 2, 2 },
+	{ pinmux(4), 2, 3 }
+};
+
+/* UART0 pin muxer settings */
 static const struct pinmux_config uart_pins[] = {
-	{ pinmux(0), 4, 6 },
-	{ pinmux(0), 4, 7 },
-	{ pinmux(4), 2, 4 },
-	{ pinmux(4), 2, 5 }
+	{ pinmux(3), 2, 7 },
+	{ pinmux(3), 2, 6 },
+	{ pinmux(3), 2, 4 },
+	{ pinmux(3), 2, 5 }
 };
 
 #ifdef CONFIG_DRIVER_TI_EMAC
@@ -73,70 +96,136 @@ static const struct pinmux_config emac_pins[] = {
 
 #ifdef CONFIG_NAND_DAVINCI
 const struct pinmux_config nand_pins[] = {
-	{ pinmux(7), 1, 1 },
-	{ pinmux(7), 1, 2 },
-	{ pinmux(7), 1, 4 },
-	{ pinmux(7), 1, 5 },
-	{ pinmux(9), 1, 0 },
-	{ pinmux(9), 1, 1 },
-	{ pinmux(9), 1, 2 },
-	{ pinmux(9), 1, 3 },
-	{ pinmux(9), 1, 4 },
-	{ pinmux(9), 1, 5 },
-	{ pinmux(9), 1, 6 },
-	{ pinmux(9), 1, 7 },
-	{ pinmux(12), 1, 5 },
-	{ pinmux(12), 1, 6 }
+	{ pinmux(7), 1, 0},	/* CS2 */
+	{ pinmux(7), 0, 1},	/* CS3  in three state*/
+	{ pinmux(7), 1, 4 },	/* EMA_WE */
+	{ pinmux(7), 1, 5 },	/* EMA_OE */
+	{ pinmux(9), 1, 0 },	/* EMA_D[7] */
+	{ pinmux(9), 1, 1 },	/* EMA_D[6] */
+	{ pinmux(9), 1, 2 },	/* EMA_D[5] */
+	{ pinmux(9), 1, 3 },	/* EMA_D[4] */
+	{ pinmux(9), 1, 4 },	/* EMA_D[3] */
+	{ pinmux(9), 1, 5 },	/* EMA_D[2] */
+	{ pinmux(9), 1, 6 },	/* EMA_D[1] */
+	{ pinmux(9), 1, 7 },	/* EMA_D[0] */
+	{ pinmux(12), 1, 5 },	/* EMA_A[2] */
+	{ pinmux(12), 1, 6 },	/* EMA_A[1] */
+	{ pinmux(6), 1, 0 }	/* EMA_CLK */
 };
 #endif
 
+const struct pinmux_config gpio_pins[] = {
+	{ pinmux(13), 8, 0 }, /* GPIO6[15] RESETOUTn on SOM*/
+	{ pinmux(13), 8, 5 }, /* GPIO6[10] U0_SW0 on EA20-00101_2*/
+	{ pinmux(13), 8, 3 }, /* GPIO6[12] U0_SW1 on EA20-00101_2*/
+	{ pinmux(19), 8, 5 }, /* GPIO6[1]  DISP_ON */
+	{ pinmux(14), 8, 1 }  /* GPIO6[6]  LCD_B_PWR*/
+};
+
+const struct pinmux_config lcd_pins[] = {
+	{ pinmux(17), 2, 1 }, /* LCD_D_0 */
+	{ pinmux(17), 2, 0 }, /* LCD_D_1 */
+	{ pinmux(16), 2, 7 }, /* LCD_D_2 */
+	{ pinmux(16), 2, 6 }, /* LCD_D_3 */
+	{ pinmux(16), 2, 5 }, /* LCD_D_4 */
+	{ pinmux(16), 2, 4 }, /* LCD_D_5 */
+	{ pinmux(16), 2, 3 }, /* LCD_D_6 */
+	{ pinmux(16), 2, 2 }, /* LCD_D_7 */
+	{ pinmux(18), 2, 1 }, /* LCD_D_8 */
+	{ pinmux(18), 2, 0 }, /* LCD_D_9 */
+	{ pinmux(17), 2, 7 }, /* LCD_D_10 */
+	{ pinmux(17), 2, 6 }, /* LCD_D_11 */
+	{ pinmux(17), 2, 5 }, /* LCD_D_12 */
+	{ pinmux(17), 2, 4 }, /* LCD_D_13 */
+	{ pinmux(17), 2, 3 }, /* LCD_D_14 */
+	{ pinmux(17), 2, 2 }, /* LCD_D_15 */
+	{ pinmux(18), 2, 6 }, /* LCD_PCLK */
+	{ pinmux(19), 2, 0 }, /* LCD_HSYNC */
+	{ pinmux(19), 2, 1 }, /* LCD_VSYNC */
+	{ pinmux(19), 2, 6 }, /* DA850_NLCD_AC_ENB_CS */
+};
+
+const struct pinmux_config halten_pin[] = {
+	{ pinmux(3),  4, 2 } /* GPIO8[6] HALTEN */
+};
+
 static const struct pinmux_resource pinmuxes[] = {
 #ifdef CONFIG_SPI_FLASH
 	PINMUX_ITEM(spi1_pins),
 #endif
 	PINMUX_ITEM(uart_pins),
+	PINMUX_ITEM(i2c_pins),
 #ifdef CONFIG_NAND_DAVINCI
 	PINMUX_ITEM(nand_pins),
 #endif
+#ifdef CONFIG_VIDEO
+	PINMUX_ITEM(lcd_pins),
+#endif
 };
 
 static const struct lpsc_resource lpsc[] = {
 	{ DAVINCI_LPSC_AEMIF },	/* NAND, NOR */
 	{ DAVINCI_LPSC_SPI1 },	/* Serial Flash */
 	{ DAVINCI_LPSC_EMAC },	/* image download */
-	{ DAVINCI_LPSC_UART2 },	/* console */
+	{ DAVINCI_LPSC_UART0 },	/* console */
 	{ DAVINCI_LPSC_GPIO },
+	{ DAVINCI_LPSC_LCDC }, /* LCD */
 };
 
-int board_init(void)
+int board_early_init_f(void)
 {
+	struct davinci_gpio *gpio6_base =
+			(struct davinci_gpio *)DAVINCI_GPIO_BANK67;
+
+	/* PinMux for GPIO */
+	if (davinci_configure_pin_mux(gpio_pins, ARRAY_SIZE(gpio_pins)) != 0)
+		return 1;
+
+	/* Set the RESETOUTn low */
+	writel((readl(&gpio6_base->set_data) & ~(1 << 15)),
+		&gpio6_base->set_data);
+	writel((readl(&gpio6_base->dir) & ~(1 << 15)), &gpio6_base->dir);
+
+	/* Set U0_SW0 low for UART0 as console*/
+	writel((readl(&gpio6_base->set_data) & ~(1 << 10)),
+		&gpio6_base->set_data);
+	writel((readl(&gpio6_base->dir) & ~(1 << 10)), &gpio6_base->dir);
+
+	/* Set U0_SW1 low for UART0 as console*/
+	writel((readl(&gpio6_base->set_data) & ~(1 << 12)),
+		&gpio6_base->set_data);
+	writel((readl(&gpio6_base->dir) & ~(1 << 12)), &gpio6_base->dir);
+
+	/* Set LCD_B_PWR low to power down LCD Backlight*/
+	writel((readl(&gpio6_base->set_data) & ~(1 << 6)),
+		&gpio6_base->set_data);
+	writel((readl(&gpio6_base->dir) & ~(1 << 6)), &gpio6_base->dir);
+
+	/* Set DISP_ON low to disable LCD output*/
+	writel((readl(&gpio6_base->set_data) & ~(1 << 1)),
+		&gpio6_base->set_data);
+	writel((readl(&gpio6_base->dir) & ~(1 << 1)), &gpio6_base->dir);
+
 #ifndef CONFIG_USE_IRQ
 	irq_init();
 #endif
 
-
-#ifdef CONFIG_NAND_DAVINCI
 	/*
 	 * NAND CS setup - cycle counts based on da850evm NAND timings in the
 	 * Linux kernel @ 25MHz EMIFA
 	 */
+#ifdef CONFIG_NAND_DAVINCI
 	writel((DAVINCI_ABCR_WSETUP(0) |
-		DAVINCI_ABCR_WSTROBE(0) |
+		DAVINCI_ABCR_WSTROBE(1) |
 		DAVINCI_ABCR_WHOLD(0) |
 		DAVINCI_ABCR_RSETUP(0) |
 		DAVINCI_ABCR_RSTROBE(1) |
 		DAVINCI_ABCR_RHOLD(0) |
 		DAVINCI_ABCR_TA(0) |
 		DAVINCI_ABCR_ASIZE_8BIT),
-	       &davinci_emif_regs->ab2cr); /* CS3 */
+	       &davinci_emif_regs->ab1cr); /* CS2 */
 #endif
 
-	/* arch number of the board */
-	gd->bd->bi_arch_number = MACH_TYPE_EA20;
-
-	/* address of boot parameters */
-	gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
-
 	/*
 	 * Power on required peripherals
 	 * ARM does not have access by default to PSC0 and PSC1
@@ -150,7 +239,7 @@ int board_init(void)
 	writel(readl(&davinci_syscfg_regs->suspsrc) &
 	       ~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C |
 		 DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 |
-		 DAVINCI_SYSCFG_SUSPSRC_UART2),
+		 DAVINCI_SYSCFG_SUSPSRC_UART0),
 	       &davinci_syscfg_regs->suspsrc);
 
 	/* configure pinmux settings */
@@ -167,10 +256,60 @@ int board_init(void)
 	/* enable the console UART */
 	writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST |
 		DAVINCI_UART_PWREMU_MGMT_UTRST),
-	       &davinci_uart2_ctrl_regs->pwremu_mgmt);
+	       &davinci_uart0_ctrl_regs->pwremu_mgmt);
+
+	/*
+	 * Reconfigure the LCDC priority to the highest to ensure that
+	 * the throughput/latency requirements for the LCDC are met.
+	 */
+	writel(readl(&davinci_syscfg_regs->mstpri[2]) & 0x0fffffff,
+	       &davinci_syscfg_regs->mstpri[2]);
+
+	/* Set LCD_B_PWR low to power up LCD Backlight*/
+	writel((readl(&gpio6_base->set_data)  | (1 << 6)),
+		&gpio6_base->set_data);
+
+	/* Set DISP_ON low to disable LCD output*/
+	writel((readl(&gpio6_base->set_data) | (1 << 1)),
+		&gpio6_base->set_data);
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* arch number of the board */
+	gd->bd->bi_arch_number = MACH_TYPE_EA20;
+
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
+
+	da8xx_video_init(&lcd_panel, 16);
+
+	return 0;
+}
+
+#ifdef BOARD_LATE_INIT
+
+int board_late_init(void)
+{
+	struct davinci_gpio *gpio8_base =
+			(struct davinci_gpio *)DAVINCI_GPIO_BANK8;
+
+	/* PinMux for HALTEN */
+	if (davinci_configure_pin_mux(halten_pin, ARRAY_SIZE(halten_pin)) != 0)
+		return 1;
+
+	/* Set HALTEN to high */
+	writel((readl(&gpio8_base->set_data) | (1 << 6)),
+		&gpio8_base->set_data);
+	writel((readl(&gpio8_base->dir) & ~(1 << 6)), &gpio8_base->dir);
+
+	setenv("stdout", "serial");
 
 	return 0;
 }
+#endif /* BOARD_LATE_INIT */
 
 #ifdef CONFIG_DRIVER_TI_EMAC
 
diff --git a/board/freescale/mx31pdk/mx31pdk.c b/board/freescale/mx31pdk/mx31pdk.c
index 0e7e0ce347..1d7b4f6d99 100644
--- a/board/freescale/mx31pdk/mx31pdk.c
+++ b/board/freescale/mx31pdk/mx31pdk.c
@@ -30,6 +30,8 @@
 #include <asm/arch/imx-regs.h>
 #include <asm/arch/sys_proto.h>
 #include <watchdog.h>
+#include <pmic.h>
+#include <fsl_pmic.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -69,16 +71,34 @@ int board_early_init_f(void)
 	return 0;
 }
 
+void enable_caches(void)
+{
+	icache_enable();
+	dcache_enable();
+}
+
 int board_init(void)
 {
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
 
+	enable_caches();
+
 	return 0;
 }
 
 int board_late_init(void)
 {
+	u32 val;
+	struct pmic *p;
+
+	pmic_init();
+	p = get_pmic();
+
+	/* Enable RTC battery */
+	pmic_reg_read(p, REG_POWER_CTL0, &val);
+	pmic_reg_write(p, REG_POWER_CTL0, val | COINCHEN);
+	pmic_reg_write(p, REG_INT_STATUS1, RTCRSTI);
 #ifdef CONFIG_HW_WATCHDOG
 	mxc_hw_watchdog_enable();
 #endif
diff --git a/board/freescale/mx35pdk/mx35pdk.h b/board/freescale/mx35pdk/mx35pdk.h
index 409aeb2289..6aeb21835b 100644
--- a/board/freescale/mx35pdk/mx35pdk.h
+++ b/board/freescale/mx35pdk/mx35pdk.h
@@ -59,24 +59,6 @@
 #define CCM_CCMR_CONFIG		0x003F4208
 #define CCM_PDR0_CONFIG		0x00801000
 
-#define PLL_BRM_OFFSET	31
-#define PLL_PD_OFFSET	26
-#define PLL_MFD_OFFSET	16
-#define PLL_MFI_OFFSET	10
-
-#define _PLL_BRM(x)	((x) << PLL_BRM_OFFSET)
-#define _PLL_PD(x)	(((x) - 1) << PLL_PD_OFFSET)
-#define _PLL_MFD(x)	(((x) - 1) << PLL_MFD_OFFSET)
-#define _PLL_MFI(x)	((x) << PLL_MFI_OFFSET)
-#define _PLL_MFN(x)	(x)
-#define _PLL_SETTING(brm, pd, mfd, mfi, mfn) \
-	(_PLL_BRM(brm) | _PLL_PD(pd) | _PLL_MFD(mfd) | _PLL_MFI(mfi) |\
-	 _PLL_MFN(mfn))
-
-#define CCM_MPLL_532_HZ	_PLL_SETTING(1, 1, 12, 11, 1)
-#define CCM_MPLL_399_HZ _PLL_SETTING(0, 1, 16, 8, 5)
-#define CCM_PPLL_300_HZ _PLL_SETTING(0, 1, 4, 6, 1)
-
 /* MEMORY SETTING */
 #define ESDCTL_0x92220000	0x92220000
 #define ESDCTL_0xA2220000	0xA2220000
diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c
index 2a0dad021e..37e6e4dbe8 100644
--- a/board/freescale/mx51evk/mx51evk.c
+++ b/board/freescale/mx51evk/mx51evk.c
@@ -38,8 +38,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-static u32 system_rev;
-
 #ifdef CONFIG_FSL_ESDHC
 struct fsl_esdhc_cfg esdhc_cfg[2] = {
 	{MMC_SDHC1_BASE_ADDR, 1},
@@ -47,11 +45,6 @@ struct fsl_esdhc_cfg esdhc_cfg[2] = {
 };
 #endif
 
-u32 get_board_rev(void)
-{
-	return system_rev;
-}
-
 int dram_init(void)
 {
 	/* dram_init must store complete ramsize in gd->ram_size */
@@ -254,16 +247,14 @@ static void power_init(void)
 	pmic_reg_write(p, REG_MODE_1, val);
 	udelay(200);
 
-	gpio_direction_output(46, 0);
-
-	/* Reset the ethernet controller over GPIO */
-	writel(0x1, IOMUXC_BASE_ADDR + 0x0AC);
-
 	/* Enable VGEN3, VCAM, VAUDIO, VVIDEO, VSD regulators */
 	val = VGEN3EN | VGEN3CONFIG | VCAMEN | VCAMCONFIG |
 		VVIDEOEN | VAUDIOEN  | VSDEN;
 	pmic_reg_write(p, REG_MODE_1, val);
 
+	mxc_request_iomux(MX51_PIN_EIM_A20, IOMUX_CONFIG_ALT1);
+	gpio_direction_output(46, 0);
+
 	udelay(500);
 
 	gpio_set_value(46, 1);
@@ -406,8 +397,6 @@ int board_early_init_f(void)
 
 int board_init(void)
 {
-	system_rev = get_cpu_rev();
-
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
 
diff --git a/board/freescale/mx53ard/mx53ard.c b/board/freescale/mx53ard/mx53ard.c
index c89da13327..be32aee14f 100644
--- a/board/freescale/mx53ard/mx53ard.c
+++ b/board/freescale/mx53ard/mx53ard.c
@@ -37,11 +37,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-u32 get_board_rev(void)
-{
-	return get_cpu_rev();
-}
-
 int dram_init(void)
 {
 	u32 size1, size2;
diff --git a/board/freescale/mx53evk/mx53evk.c b/board/freescale/mx53evk/mx53evk.c
index eab9c5f7d4..335661fd41 100644
--- a/board/freescale/mx53evk/mx53evk.c
+++ b/board/freescale/mx53evk/mx53evk.c
@@ -39,11 +39,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-u32 get_board_rev(void)
-{
-	return get_cpu_rev();
-}
-
 int dram_init(void)
 {
 	/* dram_init must store complete ramsize in gd->ram_size */
diff --git a/board/freescale/mx53loco/mx53loco.c b/board/freescale/mx53loco/mx53loco.c
index 156f8b5a3a..b4c7f33f93 100644
--- a/board/freescale/mx53loco/mx53loco.c
+++ b/board/freescale/mx53loco/mx53loco.c
@@ -38,11 +38,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-u32 get_board_rev(void)
-{
-	return get_cpu_rev();
-}
-
 int dram_init(void)
 {
 	u32 size1, size2;
diff --git a/board/freescale/mx53smd/mx53smd.c b/board/freescale/mx53smd/mx53smd.c
index 776784f5ec..87fa7fa72e 100644
--- a/board/freescale/mx53smd/mx53smd.c
+++ b/board/freescale/mx53smd/mx53smd.c
@@ -35,11 +35,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-u32 get_board_rev(void)
-{
-	return get_cpu_rev();
-}
-
 int dram_init(void)
 {
 	u32 size1, size2;
diff --git a/board/hale/tt01/Makefile b/board/hale/tt01/Makefile
new file mode 100644
index 0000000000..f6b28541e1
--- /dev/null
+++ b/board/hale/tt01/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2009 HALE electronic <helmut.raiger@hale.at>
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+COBJS	:= tt01.o
+SOBJS	:= lowlevel_init.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/hale/tt01/lowlevel_init.S b/board/hale/tt01/lowlevel_init.S
new file mode 100644
index 0000000000..6e9dc80ef6
--- /dev/null
+++ b/board/hale/tt01/lowlevel_init.S
@@ -0,0 +1,32 @@
+/*
+ * (C) Copyright 2009 Magnus Lilja <lilja.magnus@gmail.com>
+ * (C) Copyright 2011 Helmut Raiger <helmut.raiger@hale.at>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <config.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/macro.h>
+
+.globl lowlevel_init
+lowlevel_init:
+	/* Also setup the Peripheral Port Remap register inside the core */
+	ldr	r0, =ARM_PPMRR      /* start from AIPS 2GB region */
+	mcr	p15, 0, r0, c15, c2, 4
+	mov	pc, lr
diff --git a/board/hale/tt01/tt01.c b/board/hale/tt01/tt01.c
new file mode 100644
index 0000000000..2995c8f105
--- /dev/null
+++ b/board/hale/tt01/tt01.c
@@ -0,0 +1,200 @@
+/*
+ * (C) Copyright 2011 HALE electronic <helmut.raiger@hale.at>
+ * (C) Copyright 2009 Magnus Lilja <lilja.magnus@gmail.com>
+ * (c) 2007 Pengutronix, Sascha Hauer <s.hauer@pengutronix.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <command.h>
+#include <pmic.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define BOARD_STRING	"Board: HALE TT-01"
+
+/* Clock configuration */
+#define CCM_CCMR_SETUP		0x074B0BF5
+
+static void board_setup_clocks(void)
+{
+	struct clock_control_regs *ccm = (struct clock_control_regs *) CCM_BASE;
+	volatile int wait = 0x10000;
+
+	writel(CCM_CCMR_SETUP, &ccm->ccmr);
+	while (wait--)
+		;
+
+	writel(CCM_CCMR_SETUP | CCMR_MPE, &ccm->ccmr);
+	writel((CCM_CCMR_SETUP | CCMR_MPE) & ~CCMR_MDS, &ccm->ccmr);
+
+	/* Set up clock to 532MHz */
+	writel(PDR0_CSI_PODF(0x1ff) | PDR0_PER_PODF(7) |
+			PDR0_HSP_PODF(3) | PDR0_NFC_PODF(5) |
+			PDR0_IPG_PODF(1) | PDR0_MAX_PODF(3) |
+			PDR0_MCU_PODF(0), &ccm->pdr0);
+	writel(PLL_PD(0) | PLL_MFD(51) | PLL_MFI(10) | PLL_MFN(12),
+			&ccm->mpctl);
+	writel(PLL_PD(1) | PLL_MFD(4) | PLL_MFI(12) | PLL_MFN(1),
+			&ccm->spctl);
+}
+
+/* DRAM configuration */
+
+#define ESDMISC_MDDR_SETUP	0x00000004
+#define ESDMISC_MDDR_RESET_DL	0x0000000c
+/*
+ * decoding magic 0x6ac73a = 0b 0110 1010   1100 0111   0011 1010 below:
+ *   tXP = 11, tWTR = 0, tRP = 10, tMRD = 10
+ *   tWR = 1, tRAS = 100, tRRD = 01, tCAS = 11
+ *   tRCD = 011, tRC = 010
+ *  note: all but tWTR (1), tRC (111) are reset defaults,
+ *     the same values work in the jtag configuration
+ *
+ *  Bluetechnix setup has 0x75e73a (for 128MB) =
+ *			0b 0111 0101   1110 0111   0011 1010
+ *   tXP = 11, tWTR = 1, tRP = 01, tMRD = 01
+ *   tWR = 1, tRAS = 110, tRRD = 01, tCAS = 11
+ *   tRCD = 011, tRC = 010
+ */
+#define ESDCFG0_MDDR_SETUP	0x006ac73a
+#define ESDCTL_ROW_COL		(ESDCTL_SDE | ESDCTL_ROW(2) | ESDCTL_COL(2))
+#define ESDCTL_SETTINGS		(ESDCTL_ROW_COL | ESDCTL_SREFR(3) | \
+				 ESDCTL_DSIZ(2) | ESDCTL_BL(1))
+#define ESDCTL_PRECHARGE	(ESDCTL_ROW_COL | ESDCTL_CMD_PRECHARGE)
+#define ESDCTL_AUTOREFRESH	(ESDCTL_ROW_COL | ESDCTL_CMD_AUTOREFRESH)
+#define ESDCTL_LOADMODEREG	(ESDCTL_ROW_COL | ESDCTL_CMD_LOADMODEREG)
+#define ESDCTL_RW		ESDCTL_SETTINGS
+
+static void board_setup_sdram(void)
+{
+	u32 *pad;
+	struct esdc_regs *esdc = (struct esdc_regs *)ESDCTL_BASE_ADDR;
+
+	/*
+	 * setup pad control for the controller pins
+	 * no loopback, no pull, no keeper, no open drain,
+	 * standard input, standard drive, slow slew rate
+	 */
+	for (pad = (u32 *) IOMUXC_SW_PAD_CTL_SDCKE1_SDCLK_SDCLK_B;
+			pad <= (u32 *) IOMUXC_SW_PAD_CTL_VPG0_VPG1_A0; pad++)
+		*pad = 0;
+
+	/* set up MX31 DDR Memory Controller */
+	writel(ESDMISC_MDDR_SETUP, &esdc->misc);
+	writel(ESDCFG0_MDDR_SETUP, &esdc->cfg0);
+
+	/* perform DDR init sequence for CSD0 */
+	writel(ESDCTL_PRECHARGE, &esdc->ctl0);
+	writel(0x12344321, CSD0_BASE+0x0f00);
+	writel(ESDCTL_AUTOREFRESH, &esdc->ctl0);
+	writel(0x12344321, CSD0_BASE);
+	writel(0x12344321, CSD0_BASE);
+	writel(ESDCTL_LOADMODEREG, &esdc->ctl0);
+	writeb(0xda, CSD0_BASE+0x33);
+	writeb(0xff, CSD0_BASE+0x1000000);
+	writel(ESDCTL_RW, &esdc->ctl0);
+	writel(0xDEADBEEF, CSD0_BASE);
+	writel(ESDMISC_MDDR_RESET_DL, &esdc->misc);
+}
+
+static void tt01_spi3_hw_init(void)
+{
+	/* CSPI3 */
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_CSPI3_MISO, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_CSPI3_MOSI, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_CSPI3_SCLK, MUX_CTL_FUNC));
+	/* CSPI3, SS0 = Atlas */
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_CSPI2_SS0, MUX_CTL_ALT1));
+
+	/* start CSPI3 clock (3 = always on except if PLL off) */
+	setbits_le32(CCM_CGR0, 3 << 16);
+}
+
+int dram_init(void)
+{
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE,
+			PHYS_SDRAM_1_SIZE);
+	return 0;
+}
+
+int board_early_init_f(void)
+{
+	/* CS4: FPGA incl. network controller */
+	struct mxc_weimcs cs4 = {
+		/*    sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+		CSCR_U(0, 0,  0,  0,  0,  0,   0,  0,  3, 28, 1,  7,  6),
+		/*   oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+		CSCR_L(4,  4,   4,  10,  4,  0,  5,  4,  0,  0,   0,   1),
+		/*  ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+		CSCR_A(4,   4,  4,  4,  0,  1,  4,  3,  0,  0,  0,  0,  1,   0)
+	};
+
+	/* this seems essential, won't start without, but why? */
+	writel(IPU_CONF_DI_EN, (u32 *) IPU_CONF);
+
+	board_setup_clocks();
+	board_setup_sdram();
+	mxc_setup_weimcs(4, &cs4);
+
+	/* Setup UART2 and SPI3 pins */
+	mx31_uart2_hw_init();
+	tt01_spi3_hw_init();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+	return 0;
+}
+
+int board_late_init(void)
+{
+	pmic_init();
+
+#ifdef CONFIG_HW_WATCHDOG
+	mxc_hw_watchdog_enable();
+#endif
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts(BOARD_STRING "\n");
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC911X
+	rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
+#endif
+	return rc;
+}
diff --git a/board/karo/tx25/tx25.c b/board/karo/tx25/tx25.c
index d3d8ea51fd..2a29943733 100644
--- a/board/karo/tx25/tx25.c
+++ b/board/karo/tx25/tx25.c
@@ -140,7 +140,6 @@ int board_init()
 	mx25_uart1_init_pins();
 #endif
 	/* board id for linux */
-	gd->bd->bi_arch_number = MACH_TYPE_TX25;
 	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
 	return 0;
 }
diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index 6ef5e5da12..ca33aaec53 100644
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -207,8 +207,14 @@ int misc_init_r(void)
 	if (wait_for_ne != NULL) {
 		if (strcmp(wait_for_ne, "true") == 0) {
 			int cnt = 0;
+			int abort = 0;
 			puts("NE go: ");
 			while (startup_allowed() == 0) {
+				if (tstc()) {
+					(void) getc(); /* consume input */
+					abort = 1;
+					break;
+				}
 				udelay(200000);
 				cnt++;
 				if (cnt == 5)
@@ -218,7 +224,10 @@ int misc_init_r(void)
 					puts("    \b\b\b\b");
 				}
 			}
-			puts("OK\n");
+			if (abort == 1)
+				printf("\nAbort waiting for ne\n");
+			else
+				puts("OK\n");
 		}
 	}
 #endif
@@ -258,17 +267,17 @@ int board_early_init_f(void)
 	kw_gpio_set_valid(KM_KIRKWOOD_ENV_WP, 38);
 	kw_gpio_direction_output(KM_KIRKWOOD_ENV_WP, 1);
 #endif
-
+#if defined(CONFIG_KM_RECONFIG_XLX)
+	/* trigger the reconfiguration of the xilinx fpga */
+	kw_gpio_set_valid(KM_XLX_PROGRAM_B_PIN, 1);
+	kw_gpio_direction_output(KM_XLX_PROGRAM_B_PIN, 0);
+	kw_gpio_direction_input(KM_XLX_PROGRAM_B_PIN);
+#endif
 	return 0;
 }
 
 int board_init(void)
 {
-	/*
-	 * arch number of board
-	 */
-	gd->bd->bi_arch_number = MACH_TYPE_KM_KIRKWOOD;
-
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
 
@@ -396,6 +405,15 @@ int hush_init_var(void)
 #endif
 
 #if defined(CONFIG_BOOTCOUNT_LIMIT)
+const ulong patterns[]      = {	0x00000000,
+				0xFFFFFFFF,
+				0xFF00FF00,
+				0x0F0F0F0F,
+				0xF0F0F0F0};
+const ulong NBR_OF_PATTERNS = sizeof(patterns)/sizeof(*patterns);
+const ulong OFFS_PATTERN    = 3;
+const ulong REPEAT_PATTERN  = 1000;
+
 void bootcount_store(ulong a)
 {
 	volatile ulong *save_addr;
@@ -407,21 +425,34 @@ void bootcount_store(ulong a)
 	save_addr = (ulong*)(size - BOOTCOUNT_ADDR);
 	writel(a, save_addr);
 	writel(BOOTCOUNT_MAGIC, &save_addr[1]);
+
+	for (i = 0; i < REPEAT_PATTERN; i++)
+		writel(patterns[i % NBR_OF_PATTERNS],
+			&save_addr[i+OFFS_PATTERN]);
+
 }
 
 ulong bootcount_load(void)
 {
 	volatile ulong *save_addr;
 	volatile ulong size = 0;
-	int i;
+	ulong counter = 0;
+	int i, tmp;
+
 	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
 		size += gd->bd->bi_dram[i].size;
 	}
 	save_addr = (ulong*)(size - BOOTCOUNT_ADDR);
-	if (readl(&save_addr[1]) != BOOTCOUNT_MAGIC)
-		return 0;
-	else
-		return readl(save_addr);
+
+	counter = readl(&save_addr[0]);
+
+	/* Is the counter reliable, check in the big pattern for bit errors */
+	for (i = 0; (i < REPEAT_PATTERN) && (counter != 0); i++) {
+		tmp = readl(&save_addr[i+OFFS_PATTERN]);
+		if (tmp != patterns[i % NBR_OF_PATTERNS])
+			counter = 0;
+	}
+	return counter;
 }
 #endif
 
diff --git a/board/matrix_vision/mvblx/Makefile b/board/matrix_vision/mvblx/Makefile
new file mode 100644
index 0000000000..01cb517156
--- /dev/null
+++ b/board/matrix_vision/mvblx/Makefile
@@ -0,0 +1,53 @@
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS-y += mvblx.o fpga.o
+COBJS-$(CONFIG_ID_EEPROM) += sys_eeprom.o
+COBJS	:= $(COBJS-y)
+
+SRCS	:= $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+
+CFLAGS += -Werror
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+clean:
+	rm -f $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/matrix_vision/mvblx/config.mk b/board/matrix_vision/mvblx/config.mk
new file mode 100644
index 0000000000..cf055db623
--- /dev/null
+++ b/board/matrix_vision/mvblx/config.mk
@@ -0,0 +1,33 @@
+#
+# (C) Copyright 2006
+# Texas Instruments, <www.ti.com>
+#
+# Beagle Board uses OMAP3 (ARM-CortexA8) cpu
+# see http://www.ti.com/ for more information on Texas Instruments
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# Physical Address:
+# 8000'0000 (bank0)
+# A000/0000 (bank1)
+# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+
+# For use with external or internal boots.
+CONFIG_SYS_TEXT_BASE = 0x80008000
diff --git a/board/matrix_vision/mvblx/fpga.c b/board/matrix_vision/mvblx/fpga.c
new file mode 100644
index 0000000000..dacc13845d
--- /dev/null
+++ b/board/matrix_vision/mvblx/fpga.c
@@ -0,0 +1,219 @@
+/*
+ * (C) Copyright 2002
+ * Rich Ireland, Enterasys Networks, rireland@enterasys.com.
+ * Keith Outwater, keith_outwater@mvis.com.
+ *
+ * (C) Copyright 2011
+ * Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de
+ * Michael Jones, Matrix Vision GmbH, michael.jones@matrix-vision.de
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <ACEX1K.h>
+#include <command.h>
+#include <asm/gpio.h>
+#include "fpga.h"
+
+#ifdef FPGA_DEBUG
+#define fpga_debug(fmt, args...)      printf("%s: "fmt, __func__, ##args)
+#else
+#define fpga_debug(fmt, args...)
+#endif
+
+Altera_CYC2_Passive_Serial_fns altera_fns = {
+	fpga_null_fn,   /* Altera_pre_fn */
+	fpga_config_fn,
+	fpga_status_fn,
+	fpga_done_fn,
+	fpga_wr_fn,
+	fpga_null_fn,
+	fpga_null_fn,
+};
+
+Altera_desc cyclone2 = {
+	Altera_CYC2,
+	fast_passive_parallel,
+	Altera_EP3C5_SIZE,
+	(void *) &altera_fns,
+	NULL,
+	0
+};
+
+#define GPIO_RESET		43
+#define GPIO_DCLK		65
+#define GPIO_nSTATUS	157
+#define GPIO_CONF_DONE	158
+#define GPIO_nCONFIG	159
+#define GPIO_DATA0		54
+#define GPIO_DATA1		55
+#define GPIO_DATA2		56
+#define GPIO_DATA3		57
+#define GPIO_DATA4		58
+#define GPIO_DATA5		60
+#define GPIO_DATA6		61
+#define GPIO_DATA7		62
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* return FPGA_SUCCESS on success, else FPGA_FAIL
+ */
+int mvblx_init_fpga(void)
+{
+	fpga_debug("Initializing FPGA interface\n");
+	fpga_init();
+	fpga_add(fpga_altera, &cyclone2);
+
+	if (gpio_request(GPIO_DCLK, "dclk") ||
+			gpio_request(GPIO_nSTATUS, "nStatus") ||
+#ifndef CONFIG_SYS_FPGA_DONT_USE_CONF_DONE
+			gpio_request(GPIO_CONF_DONE, "conf_done") ||
+#endif
+			gpio_request(GPIO_nCONFIG, "nConfig") ||
+			gpio_request(GPIO_DATA0, "data0") ||
+			gpio_request(GPIO_DATA1, "data1") ||
+			gpio_request(GPIO_DATA2, "data2") ||
+			gpio_request(GPIO_DATA3, "data3") ||
+			gpio_request(GPIO_DATA4, "data4") ||
+			gpio_request(GPIO_DATA5, "data5") ||
+			gpio_request(GPIO_DATA6, "data6") ||
+			gpio_request(GPIO_DATA7, "data7")) {
+		printf("%s: error requesting GPIOs.", __func__);
+		return FPGA_FAIL;
+	}
+
+	/* set up outputs */
+	gpio_direction_output(GPIO_DCLK,  0);
+	gpio_direction_output(GPIO_nCONFIG, 0);
+	gpio_direction_output(GPIO_DATA0, 0);
+	gpio_direction_output(GPIO_DATA1, 0);
+	gpio_direction_output(GPIO_DATA2, 0);
+	gpio_direction_output(GPIO_DATA3, 0);
+	gpio_direction_output(GPIO_DATA4, 0);
+	gpio_direction_output(GPIO_DATA5, 0);
+	gpio_direction_output(GPIO_DATA6, 0);
+	gpio_direction_output(GPIO_DATA7, 0);
+
+	/* NB omap_free_gpio() resets to an input, so we can't
+	 * free ie. nCONFIG, or else the FPGA would reset
+	 * Q: presumably gpio_free() has the same effect?
+	 */
+
+	/* set up inputs */
+	gpio_direction_input(GPIO_nSTATUS);
+#ifndef CONFIG_SYS_FPGA_DONT_USE_CONF_DONE
+	gpio_direction_input(GPIO_CONF_DONE);
+#endif
+
+	fpga_config_fn(0, 1, 0);
+	udelay(60);
+
+	return FPGA_SUCCESS;
+}
+
+int fpga_null_fn(int cookie)
+{
+	return 0;
+}
+
+int fpga_config_fn(int assert, int flush, int cookie)
+{
+	fpga_debug("SET config : %s=%d\n", assert ? "low" : "high", assert);
+	if (flush) {
+		gpio_set_value(GPIO_nCONFIG, !assert);
+		udelay(1);
+		gpio_set_value(GPIO_nCONFIG, assert);
+	}
+
+	return assert;
+}
+
+int fpga_done_fn(int cookie)
+{
+	int result = 0;
+
+	/* since revA of BLX, we will not get this signal. */
+	udelay(10);
+#ifdef CONFIG_SYS_FPGA_DONT_USE_CONF_DONE
+	fpga_debug("not waiting for CONF_DONE.");
+	result = 1;
+#else
+	fpga_debug("CONF_DONE check ... ");
+	if (gpio_get_value(GPIO_CONF_DONE))  {
+		fpga_debug("high\n");
+		result = 1;
+	} else
+		fpga_debug("low\n");
+	gpio_free(GPIO_CONF_DONE);
+#endif
+
+	return result;
+}
+
+int fpga_status_fn(int cookie)
+{
+	int result = 0;
+	fpga_debug("STATUS check ... ");
+
+	result = gpio_get_value(GPIO_nSTATUS);
+
+	if (result < 0)
+		fpga_debug("error\n");
+	else if (result > 0)
+		fpga_debug("high\n");
+	else
+		fpga_debug("low\n");
+
+	return result;
+}
+
+static inline int _write_fpga(u8 byte)
+{
+	gpio_set_value(GPIO_DATA0, byte & 0x01);
+	gpio_set_value(GPIO_DATA1, (byte >> 1) & 0x01);
+	gpio_set_value(GPIO_DATA2, (byte >> 2) & 0x01);
+	gpio_set_value(GPIO_DATA3, (byte >> 3) & 0x01);
+	gpio_set_value(GPIO_DATA4, (byte >> 4) & 0x01);
+	gpio_set_value(GPIO_DATA5, (byte >> 5) & 0x01);
+	gpio_set_value(GPIO_DATA6, (byte >> 6) & 0x01);
+	gpio_set_value(GPIO_DATA7, (byte >> 7) & 0x01);
+
+	/* clock */
+	gpio_set_value(GPIO_DCLK, 1);
+	udelay(1);
+	gpio_set_value(GPIO_DCLK, 0);
+	udelay(1);
+
+	return 0;
+}
+
+int fpga_wr_fn(const void *buf, size_t len, int flush, int cookie)
+{
+	unsigned char *data = (unsigned char *) buf;
+	int i;
+
+	fpga_debug("fpga_wr: buf %p / size %d\n", buf, len);
+	for (i = 0; i < len; i++)
+		_write_fpga(data[i]);
+	fpga_debug("-%s\n", __func__);
+
+	return FPGA_SUCCESS;
+}
diff --git a/board/matrix_vision/mvblx/fpga.h b/board/matrix_vision/mvblx/fpga.h
new file mode 100644
index 0000000000..3d427bf573
--- /dev/null
+++ b/board/matrix_vision/mvblx/fpga.h
@@ -0,0 +1,32 @@
+/*
+ * (C) Copyright 2002
+ * Rich Ireland, Enterasys Networks, rireland@enterasys.com.
+ * Keith Outwater, keith_outwater@mvis.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+extern int mvblx_init_fpga(void);
+
+extern int fpga_status_fn(int cookie);
+extern int fpga_config_fn(int assert, int flush, int cookie);
+extern int fpga_done_fn(int cookie);
+extern int fpga_wr_fn(const void *buf, size_t len, int flush, int cookie);
+extern int fpga_null_fn(int cookie);
diff --git a/board/matrix_vision/mvblx/mvblx.c b/board/matrix_vision/mvblx/mvblx.c
new file mode 100644
index 0000000000..74b5b19be2
--- /dev/null
+++ b/board/matrix_vision/mvblx/mvblx.c
@@ -0,0 +1,169 @@
+/*
+ * MATRIX VISION GmbH mvBlueLYNX-X
+ *
+ * Derived from Beagle and Overo
+ *
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ *	Sunil Kumar <sunilsaini05@gmail.com>
+ *	Shashi Ranjan <shashiranjanmca05@gmail.com>
+ *
+ * Derived from Beagle Board and 3430 SDP code by
+ *	Richard Woodruff <r-woodruff2@ti.com>
+ *	Syed Mohammed Khasim <khasim@ti.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <netdev.h>
+#include <twl4030.h>
+#include <asm/io.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/gpio.h>
+#include <asm/mach-types.h>
+#include "mvblx.h"
+#include "fpga.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#if defined(CONFIG_CMD_NET)
+static void setup_net_chip(void);
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * Routine: board_init
+ * Description: Early hardware init.
+ */
+int board_init(void)
+{
+	gpmc_init();	/* in SRAM or SDRAM, finish GPMC */
+	/* boot param addr */
+	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+	return 0;
+}
+
+/*
+ * Routine: misc_init_r
+ * Description: Configure board specific parts
+ */
+int misc_init_r(void)
+{
+	printf("mvBlueLYNX-X\n");
+	if (get_cpu_family() == CPU_OMAP36XX)
+		setenv("mpurate", "1000");
+	else
+		setenv("mpurate", "600");
+
+	twl4030_power_init();
+
+#if defined(CONFIG_CMD_NET)
+	setup_net_chip();
+#endif /* CONFIG_CMD_NET */
+
+	mvblx_init_fpga();
+
+	mac_read_from_eeprom();
+
+	dieid_num_r();
+
+	return 0;
+}
+
+/*
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ *		hardware. Many pins need to be moved from protect to primary
+ *		mode.
+ */
+void set_muxconf_regs(void)
+{
+	MUX_MVBLX();
+}
+
+#ifdef CONFIG_GENERIC_MMC
+int board_mmc_init(bd_t *bis)
+{
+	omap_mmc_init(0);
+	omap_mmc_init(1);
+	return 0;
+}
+#endif
+
+#if defined(CONFIG_CMD_NET)
+/*
+ * Routine: setup_net_chip
+ * Description: Setting up the configuration GPMC registers specific to the
+ *		Ethernet hardware.
+ */
+static void setup_net_chip(void)
+{
+	struct gpio *gpio5_base = (struct gpio *)OMAP34XX_GPIO5_BASE;
+	struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;
+
+	/* Configure GPMC registers */
+	writel(NET_GPMC_CONFIG1, &gpmc_cfg->cs[0].config1);
+	writel(NET_GPMC_CONFIG2, &gpmc_cfg->cs[0].config2);
+	writel(NET_GPMC_CONFIG3, &gpmc_cfg->cs[0].config3);
+	writel(NET_GPMC_CONFIG4, &gpmc_cfg->cs[0].config4);
+	writel(NET_GPMC_CONFIG5, &gpmc_cfg->cs[0].config5);
+	writel(NET_GPMC_CONFIG6, &gpmc_cfg->cs[0].config6);
+	writel(NET_GPMC_CONFIG7, &gpmc_cfg->cs[0].config7);
+
+	/* Enable off mode for NWE in PADCONF_GPMC_NWE register */
+	writew(readw(&ctrl_base->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
+	/* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
+	writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
+	/* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
+	writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
+		&ctrl_base->gpmc_nadv_ale);
+
+	/* Make GPIO 139 as output pin */
+	writel(readl(&gpio5_base->oe) & ~(GPIO11), &gpio5_base->oe);
+
+	/* Now send a pulse on the GPIO pin */
+	writel(GPIO11, &gpio5_base->setdataout);
+	udelay(1);
+	writel(GPIO11, &gpio5_base->cleardataout);
+	udelay(1);
+	writel(GPIO11, &gpio5_base->setdataout);
+}
+
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC911X
+	rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
+#endif
+	return rc;
+}
+
+int overwrite_console(void)
+{
+	/* return TRUE if console should be overwritten */
+	return 0;
+}
+
+#endif /* CONFIG_CMD_NET */
diff --git a/board/matrix_vision/mvblx/mvblx.h b/board/matrix_vision/mvblx/mvblx.h
new file mode 100644
index 0000000000..cda5b0bd01
--- /dev/null
+++ b/board/matrix_vision/mvblx/mvblx.h
@@ -0,0 +1,362 @@
+/*
+ * (C) Copyright 2008
+ * Dirk Behme <dirk.behme@gmail.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _MVBLX_H_
+#define _MVBLX_H_
+
+#include <asm/arch/sys_proto.h>
+
+const omap3_sysinfo sysinfo = {
+	DDR_DISCRETE,
+	"OMAP3 mvBlueLYNX-X camera",
+	"no NAND",
+};
+
+/*
+ * IEN  - Input Enable
+ * IDIS - Input Disable
+ * PTD  - Pull type Down
+ * PTU  - Pull type Up
+ * DIS  - Pull type selection is inactive
+ * EN   - Pull type selection is active
+ * M0   - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_MVBLX() \
+ /*SDRC*/\
+	MUX_VAL(CP(SDRC_D0),		(IEN  | PTD | DIS | M0)) /*SDRC_D0*/\
+	MUX_VAL(CP(SDRC_D1),		(IEN  | PTD | DIS | M0)) /*SDRC_D1*/\
+	MUX_VAL(CP(SDRC_D2),		(IEN  | PTD | DIS | M0)) /*SDRC_D2*/\
+	MUX_VAL(CP(SDRC_D3),		(IEN  | PTD | DIS | M0)) /*SDRC_D3*/\
+	MUX_VAL(CP(SDRC_D4),		(IEN  | PTD | DIS | M0)) /*SDRC_D4*/\
+	MUX_VAL(CP(SDRC_D5),		(IEN  | PTD | DIS | M0)) /*SDRC_D5*/\
+	MUX_VAL(CP(SDRC_D6),		(IEN  | PTD | DIS | M0)) /*SDRC_D6*/\
+	MUX_VAL(CP(SDRC_D7),		(IEN  | PTD | DIS | M0)) /*SDRC_D7*/\
+	MUX_VAL(CP(SDRC_D8),		(IEN  | PTD | DIS | M0)) /*SDRC_D8*/\
+	MUX_VAL(CP(SDRC_D9),		(IEN  | PTD | DIS | M0)) /*SDRC_D9*/\
+	MUX_VAL(CP(SDRC_D10),		(IEN  | PTD | DIS | M0)) /*SDRC_D10*/\
+	MUX_VAL(CP(SDRC_D11),		(IEN  | PTD | DIS | M0)) /*SDRC_D11*/\
+	MUX_VAL(CP(SDRC_D12),		(IEN  | PTD | DIS | M0)) /*SDRC_D12*/\
+	MUX_VAL(CP(SDRC_D13),		(IEN  | PTD | DIS | M0)) /*SDRC_D13*/\
+	MUX_VAL(CP(SDRC_D14),		(IEN  | PTD | DIS | M0)) /*SDRC_D14*/\
+	MUX_VAL(CP(SDRC_D15),		(IEN  | PTD | DIS | M0)) /*SDRC_D15*/\
+	MUX_VAL(CP(SDRC_D16),		(IEN  | PTD | DIS | M0)) /*SDRC_D16*/\
+	MUX_VAL(CP(SDRC_D17),		(IEN  | PTD | DIS | M0)) /*SDRC_D17*/\
+	MUX_VAL(CP(SDRC_D18),		(IEN  | PTD | DIS | M0)) /*SDRC_D18*/\
+	MUX_VAL(CP(SDRC_D19),		(IEN  | PTD | DIS | M0)) /*SDRC_D19*/\
+	MUX_VAL(CP(SDRC_D20),		(IEN  | PTD | DIS | M0)) /*SDRC_D20*/\
+	MUX_VAL(CP(SDRC_D21),		(IEN  | PTD | DIS | M0)) /*SDRC_D21*/\
+	MUX_VAL(CP(SDRC_D22),		(IEN  | PTD | DIS | M0)) /*SDRC_D22*/\
+	MUX_VAL(CP(SDRC_D23),		(IEN  | PTD | DIS | M0)) /*SDRC_D23*/\
+	MUX_VAL(CP(SDRC_D24),		(IEN  | PTD | DIS | M0)) /*SDRC_D24*/\
+	MUX_VAL(CP(SDRC_D25),		(IEN  | PTD | DIS | M0)) /*SDRC_D25*/\
+	MUX_VAL(CP(SDRC_D26),		(IEN  | PTD | DIS | M0)) /*SDRC_D26*/\
+	MUX_VAL(CP(SDRC_D27),		(IEN  | PTD | DIS | M0)) /*SDRC_D27*/\
+	MUX_VAL(CP(SDRC_D28),		(IEN  | PTD | DIS | M0)) /*SDRC_D28*/\
+	MUX_VAL(CP(SDRC_D29),		(IEN  | PTD | DIS | M0)) /*SDRC_D29*/\
+	MUX_VAL(CP(SDRC_D30),		(IEN  | PTD | DIS | M0)) /*SDRC_D30*/\
+	MUX_VAL(CP(SDRC_D31),		(IEN  | PTD | DIS | M0)) /*SDRC_D31*/\
+	MUX_VAL(CP(SDRC_CLK),		(IEN  | PTD | DIS | M0)) /*SDRC_CLK*/\
+	MUX_VAL(CP(SDRC_DQS0),		(IEN  | PTD | DIS | M0)) /*SDRC_DQS0*/\
+	MUX_VAL(CP(SDRC_DQS1),		(IEN  | PTD | DIS | M0)) /*SDRC_DQS1*/\
+	MUX_VAL(CP(SDRC_DQS2),		(IEN  | PTD | DIS | M0)) /*SDRC_DQS2*/\
+	MUX_VAL(CP(SDRC_DQS3),		(IEN  | PTD | DIS | M0)) /*SDRC_DQS3*/\
+ /*GPMC*/\
+	MUX_VAL(CP(GPMC_A1),		(IDIS | PTU | EN  | M0)) /*GPMC_A1*/\
+	MUX_VAL(CP(GPMC_A2),		(IDIS | PTU | EN  | M0)) /*GPMC_A2*/\
+	MUX_VAL(CP(GPMC_A3),		(IDIS | PTU | EN  | M0)) /*GPMC_A3*/\
+	MUX_VAL(CP(GPMC_A4),		(IDIS | PTU | EN  | M0)) /*GPMC_A4*/\
+	MUX_VAL(CP(GPMC_A5),		(IDIS | PTU | EN  | M0)) /*GPMC_A5*/\
+	MUX_VAL(CP(GPMC_A6),		(IDIS | PTU | EN  | M0)) /*GPMC_A6*/\
+	MUX_VAL(CP(GPMC_A7),		(IDIS | PTU | EN  | M0)) /*GPMC_A7*/\
+	MUX_VAL(CP(GPMC_A8),		(IDIS | PTU | EN  | M4)) /*GPIO_41*/\
+	MUX_VAL(CP(GPMC_A9),		(IDIS | PTU | EN  | M4)) /*GPIO_42*/\
+	MUX_VAL(CP(GPMC_A10),		(IDIS | PTU | EN  | M4)) /*GPIO_43*/\
+	MUX_VAL(CP(GPMC_D0),		(IEN  | PTU | EN  | M0)) /*GPMC_D0*/\
+	MUX_VAL(CP(GPMC_D1),		(IEN  | PTU | EN  | M0)) /*GPMC_D1*/\
+	MUX_VAL(CP(GPMC_D2),		(IEN  | PTU | EN  | M0)) /*GPMC_D2*/\
+	MUX_VAL(CP(GPMC_D3),		(IEN  | PTU | EN  | M0)) /*GPMC_D3*/\
+	MUX_VAL(CP(GPMC_D4),		(IEN  | PTU | EN  | M0)) /*GPMC_D4*/\
+	MUX_VAL(CP(GPMC_D5),		(IEN  | PTU | EN  | M0)) /*GPMC_D5*/\
+	MUX_VAL(CP(GPMC_D6),		(IEN  | PTU | EN  | M0)) /*GPMC_D6*/\
+	MUX_VAL(CP(GPMC_D7),		(IEN  | PTU | EN  | M0)) /*GPMC_D7*/\
+	MUX_VAL(CP(GPMC_D8),		(IEN  | PTU | EN  | M0)) /*GPMC_D8*/\
+	MUX_VAL(CP(GPMC_D9),		(IEN  | PTU | EN  | M0)) /*GPMC_D9*/\
+	MUX_VAL(CP(GPMC_D10),		(IEN  | PTU | EN  | M0)) /*GPMC_D10*/\
+	MUX_VAL(CP(GPMC_D11),		(IEN  | PTU | EN  | M0)) /*GPMC_D11*/\
+	MUX_VAL(CP(GPMC_D12),		(IEN  | PTU | EN  | M0)) /*GPMC_D12*/\
+	MUX_VAL(CP(GPMC_D13),		(IEN  | PTU | EN  | M0)) /*GPMC_D13*/\
+	MUX_VAL(CP(GPMC_D14),		(IEN  | PTU | EN  | M0)) /*GPMC_D14*/\
+	MUX_VAL(CP(GPMC_D15),		(IEN  | PTU | EN  | M0)) /*GPMC_D15*/\
+	MUX_VAL(CP(GPMC_NCS0),		(IDIS | PTU | EN  | M0)) /*GPMC_nCS0*/\
+	MUX_VAL(CP(GPMC_NCS1),		(IDIS | PTU | EN  | M0)) /*GPMC_nCS1*/\
+	MUX_VAL(CP(GPMC_NCS2),		(IDIS | PTU | EN  | M0)) /*GPMC_nCS2*/\
+	MUX_VAL(CP(GPMC_NCS3),		(IEN  | PTU | EN  | M4)) /*GPIO54*/\
+	MUX_VAL(CP(GPMC_NCS4),		(IEN  | PTU | EN  | M4)) /*GPIO55*/\
+	MUX_VAL(CP(GPMC_NCS5),		(IEN  | PTU | EN  | M4)) /*GPIO56*/\
+	MUX_VAL(CP(GPMC_NCS6),		(IEN  | PTU | EN  | M4)) /*GPIO57*/\
+	MUX_VAL(CP(GPMC_NCS7),		(IEN  | PTU | EN  | M4)) /*GPIO58*/\
+	MUX_VAL(CP(GPMC_CLK),		(IDIS | PTU | EN | M0)) /*GPMC_CLK*/\
+	MUX_VAL(CP(GPMC_NADV_ALE),	(IDIS | PTD | DIS | M0)) /*GPMC_nADV_ALE*/\
+	MUX_VAL(CP(GPMC_NOE),		(IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\
+	MUX_VAL(CP(GPMC_NWE),		(IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\
+	MUX_VAL(CP(GPMC_NBE0_CLE),	(IEN  | PTU | EN  | M4)) /*GPIO60*/\
+	MUX_VAL(CP(GPMC_NBE1),		(IEN  | PTU | EN  | M4)) /*GPIO61*/\
+	MUX_VAL(CP(GPMC_NWP),		(IEN  | PTU | EN  | M4)) /*GPIO62*/\
+	MUX_VAL(CP(GPMC_WAIT0),		(IEN  | PTU | EN  | M0)) /*GPMC_WAIT0*/\
+	MUX_VAL(CP(GPMC_WAIT3),		(IDIS  | PTU | EN  | M4)) /*GPIO65*/\
+ /*DSS*/\
+	MUX_VAL(CP(DSS_PCLK),		(IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
+	MUX_VAL(CP(DSS_HSYNC),		(IDIS | PTD | DIS | M0)) /*DSS_HSYNC*/\
+	MUX_VAL(CP(DSS_VSYNC),		(IDIS | PTD | DIS | M0)) /*DSS_VSYNC*/\
+	MUX_VAL(CP(DSS_ACBIAS),		(IDIS | PTD | DIS | M0)) /*DSS_ACBIAS*/\
+	MUX_VAL(CP(DSS_DATA0),		(IDIS | PTD | DIS | M4)) /*not_used*/\
+	MUX_VAL(CP(DSS_DATA1),		(IDIS | PTD | DIS | M4)) /*not_used*/\
+	MUX_VAL(CP(DSS_DATA2),		(IDIS | PTD | DIS | M4)) /*not_used*/\
+	MUX_VAL(CP(DSS_DATA3),		(IDIS | PTD | DIS | M4)) /*not_used*/\
+	MUX_VAL(CP(DSS_DATA4),		(IDIS | PTD | DIS | M4)) /*not_used*/\
+	MUX_VAL(CP(DSS_DATA5),		(IDIS | PTD | DIS | M4)) /*not_used*/\
+	MUX_VAL(CP(DSS_DATA6),		(IDIS | PTD | DIS | M0)) /*DSS_DATA6*/\
+	MUX_VAL(CP(DSS_DATA7),		(IDIS | PTD | DIS | M0)) /*DSS_DATA7*/\
+	MUX_VAL(CP(DSS_DATA8),		(IDIS | PTD | DIS | M0)) /*DSS_DATA8*/\
+	MUX_VAL(CP(DSS_DATA9),		(IDIS | PTD | DIS | M0)) /*DSS_DATA9*/\
+	MUX_VAL(CP(DSS_DATA10),		(IDIS | PTD | DIS | M0)) /*DSS_DATA10*/\
+	MUX_VAL(CP(DSS_DATA11),		(IDIS | PTD | DIS | M0)) /*DSS_DATA11*/\
+	MUX_VAL(CP(DSS_DATA12),		(IDIS | PTD | DIS | M0)) /*DSS_DATA12*/\
+	MUX_VAL(CP(DSS_DATA13),		(IDIS | PTD | DIS | M0)) /*DSS_DATA13*/\
+	MUX_VAL(CP(DSS_DATA14),		(IDIS | PTD | DIS | M0)) /*DSS_DATA14*/\
+	MUX_VAL(CP(DSS_DATA15),		(IDIS | PTD | DIS | M0)) /*DSS_DATA15*/\
+	MUX_VAL(CP(DSS_DATA16),		(IDIS | PTD | DIS | M0)) /*DSS_DATA16*/\
+	MUX_VAL(CP(DSS_DATA17),		(IDIS | PTD | DIS | M0)) /*DSS_DATA17*/\
+	MUX_VAL(CP(DSS_DATA18),		(IDIS | PTD | DIS | M3)) /*DSS_DATA0*/\
+	MUX_VAL(CP(DSS_DATA19),		(IDIS | PTD | DIS | M3)) /*DSS_DATA1*/\
+	MUX_VAL(CP(DSS_DATA20),		(IDIS | PTD | DIS | M3)) /*DSS_DATA2*/\
+	MUX_VAL(CP(DSS_DATA21),		(IDIS | PTD | DIS | M3)) /*DSS_DATA3*/\
+	MUX_VAL(CP(DSS_DATA22),		(IDIS | PTD | DIS | M3)) /*DSS_DATA4*/\
+	MUX_VAL(CP(DSS_DATA23),		(IDIS | PTD | DIS | M3)) /*DSS_DATA5*/\
+ /*CAMERA*/\
+	MUX_VAL(CP(CAM_HS),		(IEN  | PTU | EN  | M0)) /*CAM_HS */\
+	MUX_VAL(CP(CAM_VS),		(IEN  | PTU | EN  | M0)) /*CAM_VS */\
+	MUX_VAL(CP(CAM_XCLKA),		(IDIS | PTD | DIS | M0)) /*CAM_XCLKA*/\
+	MUX_VAL(CP(CAM_PCLK),		(IEN  | PTU | EN  | M0)) /*CAM_PCLK*/\
+	MUX_VAL(CP(CAM_FLD),		(IDIS | PTD | DIS | M4)) /*GPIO_98*/\
+	MUX_VAL(CP(CAM_D0),		(IEN  | PTD | DIS | M0)) /*CAM_D0*/\
+	MUX_VAL(CP(CAM_D1),		(IEN  | PTD | DIS | M0)) /*CAM_D1*/\
+	MUX_VAL(CP(CAM_D2),		(IEN  | PTD | DIS | M0)) /*CAM_D2*/\
+	MUX_VAL(CP(CAM_D3),		(IEN  | PTD | DIS | M0)) /*CAM_D3*/\
+	MUX_VAL(CP(CAM_D4),		(IEN  | PTD | DIS | M0)) /*CAM_D4*/\
+	MUX_VAL(CP(CAM_D5),		(IEN  | PTD | DIS | M0)) /*CAM_D5*/\
+	MUX_VAL(CP(CAM_D6),		(IEN  | PTD | DIS | M0)) /*CAM_D6*/\
+	MUX_VAL(CP(CAM_D7),		(IEN  | PTD | DIS | M0)) /*CAM_D7*/\
+	MUX_VAL(CP(CAM_D8),		(IEN  | PTD | DIS | M0)) /*CAM_D8*/\
+	MUX_VAL(CP(CAM_D9),		(IEN  | PTD | DIS | M0)) /*CAM_D9*/\
+	MUX_VAL(CP(CAM_D10),		(IEN  | PTD | DIS | M0)) /*CAM_D10*/\
+	MUX_VAL(CP(CAM_D11),		(IEN  | PTD | DIS | M0)) /*CAM_D11*/\
+	MUX_VAL(CP(CAM_XCLKB),		(IDIS | PTD | DIS | M0)) /*CAM_XCLKB*/\
+	MUX_VAL(CP(CAM_WEN),		(IEN  | PTD | DIS | M4)) /*GPIO_167*/\
+	MUX_VAL(CP(CAM_STROBE),		(IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
+	MUX_VAL(CP(CSI2_DX0),		(IEN  | PTD | DIS | M0)) /*CSI2_DX0*/\
+	MUX_VAL(CP(CSI2_DY0),		(IEN  | PTD | DIS | M0)) /*CSI2_DY0*/\
+	MUX_VAL(CP(CSI2_DX1),		(IEN  | PTD | DIS | M0)) /*CSI2_DX1*/\
+	MUX_VAL(CP(CSI2_DY1),		(IEN  | PTD | DIS | M0)) /*CSI2_DY1*/\
+ /*Audio Interface */\
+	MUX_VAL(CP(MCBSP2_FSX),		(IEN  | PTD | DIS | M0)) /*McBSP2_FSX*/\
+	MUX_VAL(CP(MCBSP2_CLKX),	(IEN  | PTD | DIS | M0)) /*McBSP2_CLKX*/\
+	MUX_VAL(CP(MCBSP2_DR),		(IEN  | PTD | DIS | M0)) /*McBSP2_DR*/\
+	MUX_VAL(CP(MCBSP2_DX),		(IDIS | PTD | DIS | M0)) /*McBSP2_DX*/\
+ /*Expansion card 1*/\
+	MUX_VAL(CP(MMC1_CLK),		(IDIS | PTU | EN  | M0)) /*MMC1_CLK*/\
+	MUX_VAL(CP(MMC1_CMD),		(IEN  | PTU | EN  | M0)) /*MMC1_CMD*/\
+	MUX_VAL(CP(MMC1_DAT0),		(IEN  | PTU | EN  | M0)) /*MMC1_DAT0*/\
+	MUX_VAL(CP(MMC1_DAT1),		(IEN  | PTU | EN  | M0)) /*MMC1_DAT1*/\
+	MUX_VAL(CP(MMC1_DAT2),		(IEN  | PTU | EN  | M0)) /*MMC1_DAT2*/\
+	MUX_VAL(CP(MMC1_DAT3),		(IEN  | PTU | EN  | M0)) /*MMC1_DAT3*/\
+	MUX_VAL(CP(MMC1_DAT4),		(IDIS  | PTU | DIS  | M4)) /*GPIO_?*/\
+	MUX_VAL(CP(MMC1_DAT5),		(IDIS  | PTU | DIS  | M4)) /*GPIO_?*/\
+	MUX_VAL(CP(MMC1_DAT6),		(IDIS  | PTU | DIS  | M4)) /*GPIO_?*/\
+	MUX_VAL(CP(MMC1_DAT7),		(IEN  | PTU | DIS  | M7)) /*GPIO_129 disabled*/\
+ /*Expansion card 2 */\
+	MUX_VAL(CP(MMC2_CLK),		(IEN  | PTU | DIS  | M0)) /*MMC2_CLK*/\
+	MUX_VAL(CP(MMC2_CMD),		(IEN  | PTU | DIS  | M0)) /*MMC2_CMD*/\
+	MUX_VAL(CP(MMC2_DAT0),		(IEN  | PTU | DIS  | M0)) /*MMC2_DAT0*/\
+	MUX_VAL(CP(MMC2_DAT1),		(IEN  | PTU | DIS  | M0)) /*MMC2_DAT1*/\
+	MUX_VAL(CP(MMC2_DAT2),		(IEN  | PTU | DIS  | M0)) /*MMC2_DAT2*/\
+	MUX_VAL(CP(MMC2_DAT3),		(IEN  | PTU | DIS  | M0)) /*MMC2_DAT3*/\
+	MUX_VAL(CP(MMC2_DAT4),		(IDIS  | PTU | DIS  | M4)) /*GPIO_136*/\
+	MUX_VAL(CP(MMC2_DAT5),		(IEN  | PTU | EN  | M4)) /*GPIO_137*/\
+	MUX_VAL(CP(MMC2_DAT6),		(IDIS  | PTU | DIS  | M4)) /*GPIO_138*/\
+	MUX_VAL(CP(MMC2_DAT7),		(IEN  | PTU | EN  | M4)) /*GPIO_139*/\
+ /*Bluetooth*/\
+	MUX_VAL(CP(MCBSP3_DX),		(IDIS | PTD | DIS | M1)) /*UART2_CTS*/\
+	MUX_VAL(CP(MCBSP3_DR),		(IDIS | PTD | DIS | M1)) /*UART2_RTS*/\
+	MUX_VAL(CP(MCBSP3_CLKX),	(IDIS | PTD | DIS | M1)) /*UART2_TX*/\
+	MUX_VAL(CP(MCBSP3_FSX),		(IDIS | PTD | DIS | M1)) /*UART2_RX*/\
+ /*Modem Interface */\
+	MUX_VAL(CP(UART1_TX),		(IDIS | PTD | DIS | M0)) /*UART1_TX*/\
+	MUX_VAL(CP(UART1_RTS),		(IDIS | PTD | DIS | M4)) /*GPIO_149*/ \
+	MUX_VAL(CP(UART1_CTS),		(IEN | PTU | EN | M4)) /*GPIO_150*/ \
+	MUX_VAL(CP(UART1_RX),		(IEN  | PTD | DIS | M0)) /*UART1_RX*/\
+	MUX_VAL(CP(MCBSP1_CLKR),	(IDIS | PTD | DIS | M4)) /*GPIO_156*/\
+	MUX_VAL(CP(MCBSP1_FSR),		(IEN | PTU | EN  | M4)) /*GPIO_157*/\
+	MUX_VAL(CP(MCBSP1_DX),		(IEN | PTU | DIS | M4)) /*GPIO_158 1-wire */\
+	MUX_VAL(CP(MCBSP1_DR),		(IDIS | PTD | DIS | M4)) /*GPIO_159*/\
+	MUX_VAL(CP(MCBSP_CLKS),		(IEN  | PTU | DIS | M0)) /*McBSP_CLKS*/\
+	MUX_VAL(CP(MCBSP1_FSX),		(IDIS | PTD | DIS | M4)) /*GPIO_161*/\
+	MUX_VAL(CP(MCBSP1_CLKX),	(IDIS | PTD | DIS | M4)) /*GPIO_162*/\
+ /*Serial Interface*/\
+	MUX_VAL(CP(UART3_CTS_RCTX),	(IEN  | PTD | EN  | M0)) /*UART3_CTS_RCTX*/\
+	MUX_VAL(CP(UART3_RTS_SD),	(IDIS | PTD | DIS | M0)) /*UART3_RTS_SD */\
+	MUX_VAL(CP(UART3_RX_IRRX),	(IEN  | PTD | DIS | M0)) /*UART3_RX_IRRX*/\
+	MUX_VAL(CP(UART3_TX_IRTX),	(IDIS | PTD | DIS | M0)) /*UART3_TX_IRTX*/\
+	MUX_VAL(CP(HSUSB0_CLK),		(IEN  | PTD | DIS | M0)) /*HSUSB0_CLK*/\
+	MUX_VAL(CP(HSUSB0_STP),		(IDIS | PTU | EN  | M0)) /*HSUSB0_STP*/\
+	MUX_VAL(CP(HSUSB0_DIR),		(IEN  | PTD | DIS | M0)) /*HSUSB0_DIR*/\
+	MUX_VAL(CP(HSUSB0_NXT),		(IEN  | PTD | DIS | M0)) /*HSUSB0_NXT*/\
+	MUX_VAL(CP(HSUSB0_DATA0),	(IEN  | PTD | DIS | M0)) /*HSUSB0_DATA0*/\
+	MUX_VAL(CP(HSUSB0_DATA1),	(IEN  | PTD | DIS | M0)) /*HSUSB0_DATA1*/\
+	MUX_VAL(CP(HSUSB0_DATA2),	(IEN  | PTD | DIS | M0)) /*HSUSB0_DATA2*/\
+	MUX_VAL(CP(HSUSB0_DATA3),	(IEN  | PTD | DIS | M0)) /*HSUSB0_DATA3*/\
+	MUX_VAL(CP(HSUSB0_DATA4),	(IEN  | PTD | DIS | M0)) /*HSUSB0_DATA4*/\
+	MUX_VAL(CP(HSUSB0_DATA5),	(IEN  | PTD | DIS | M0)) /*HSUSB0_DATA5*/\
+	MUX_VAL(CP(HSUSB0_DATA6),	(IEN  | PTD | DIS | M0)) /*HSUSB0_DATA6*/\
+	MUX_VAL(CP(HSUSB0_DATA7),	(IEN  | PTD | DIS | M0)) /*HSUSB0_DATA7*/\
+	MUX_VAL(CP(I2C1_SCL),		(IEN  | PTU | EN  | M0)) /*I2C1_SCL*/\
+	MUX_VAL(CP(I2C1_SDA),		(IEN  | PTU | EN  | M0)) /*I2C1_SDA*/\
+	MUX_VAL(CP(I2C2_SCL),		(IEN  | PTU | EN  | M0)) /*I2C2_SCL*/\
+	MUX_VAL(CP(I2C2_SDA),		(IEN  | PTU | EN  | M0)) /*I2C2_SDA*/\
+	MUX_VAL(CP(I2C3_SCL),		(IEN  | PTU | EN  | M0)) /*I2C3_SCL*/\
+	MUX_VAL(CP(I2C3_SDA),		(IEN  | PTU | EN  | M0)) /*I2C3_SDA*/\
+	MUX_VAL(CP(I2C4_SCL),		(IEN  | PTU | EN  | M0)) /*I2C4_SCL*/\
+	MUX_VAL(CP(I2C4_SDA),		(IEN  | PTU | EN  | M0)) /*I2C4_SDA*/\
+	MUX_VAL(CP(HDQ_SIO),		(IDIS | PTU | EN  | M4)) /*GPIO_170*/\
+	MUX_VAL(CP(MCSPI1_CLK),		(IDIS  | PTU | DIS  | M4)) /*GPIO_171*/\
+	MUX_VAL(CP(MCSPI1_SIMO),	(IDIS  | PTU | DIS  | M4)) /*GPIO_172*/\
+	MUX_VAL(CP(MCSPI1_SOMI),	(IDIS  | PTU | DIS  | M4)) /*GPIO_173*/\
+	MUX_VAL(CP(MCSPI1_CS0),		(IDIS  | PTD | DIS  | M4)) /*GPIO_174*/\
+	MUX_VAL(CP(MCSPI1_CS3),		(IDIS  | PTU | DIS | M4)) /*GPIO_177*/\
+ /* USB EHCI (port 2) not used */\
+	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | DIS | M0)) /*McSPI2_CLK*/\
+	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | DIS | M0)) /*McSPI2_SIMO*/\
+	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | DIS | M0)) /*McSPI2_SOMI*/\
+	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | EN  | M0)) /*McSPI2_CS0*/\
+	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | EN  | M0)) /*McSPI2_CS1*/\
+ /*Control and debug */\
+	MUX_VAL(CP(SYS_32K),		(IEN  | PTD | DIS | M0)) /*SYS_32K*/\
+	MUX_VAL(CP(SYS_CLKREQ),		(IEN  | PTD | DIS | M0)) /*SYS_CLKREQ*/\
+	MUX_VAL(CP(SYS_NIRQ),		(IEN  | PTU | EN  | M0)) /*SYS_nIRQ*/\
+	MUX_VAL(CP(SYS_BOOT0),		(IDIS | PTD | DIS | M3)) /*DSS_DATA18*/\
+	MUX_VAL(CP(SYS_BOOT1),		(IDIS | PTD | DIS | M3)) /*DSS_DATA19*/\
+	MUX_VAL(CP(SYS_BOOT2),		(IEN  | PTD | DIS | M0)) /*GPIO_4*/\
+	MUX_VAL(CP(SYS_BOOT3),		(IDIS | PTD | DIS | M3)) /*DSS_DATA20*/\
+	MUX_VAL(CP(SYS_BOOT4),		(IDIS | PTD | DIS | M3)) /*DSS_DATA21*/\
+	MUX_VAL(CP(SYS_BOOT5),		(IDIS | PTD | DIS | M3)) /*DSS_DATA22*/\
+	MUX_VAL(CP(SYS_BOOT6),		(IDIS | PTD | DIS | M3)) /*DSS_DATA23*/ \
+	MUX_VAL(CP(SYS_OFF_MODE),	(IEN  | PTD | DIS | M0)) /*SYS_OFF_MODE*/\
+	MUX_VAL(CP(SYS_CLKOUT1),	(IDIS  | PTD | DIS | M4)) /*GPIO_10*/\
+	MUX_VAL(CP(SYS_CLKOUT2),	(IEN  | PTD | DIS  | M0)) /*SYS_CLKOUT2*/\
+ /* USB EHCI (port 1) */\
+	MUX_VAL(CP(ETK_CLK_ES2),	(IDIS | PTU | EN  | M3)) /*HSUSB1_STP*/\
+	MUX_VAL(CP(ETK_CTL_ES2),	(IDIS | PTU | DIS | M3)) /*HSUSB1_CLK*/\
+	MUX_VAL(CP(ETK_D0_ES2),		(IEN  | PTU | DIS | M3)) /*HSUSB1_DATA0*/\
+	MUX_VAL(CP(ETK_D1_ES2),		(IEN  | PTU | DIS | M3)) /*HSUSB1_DATA1*/\
+	MUX_VAL(CP(ETK_D2_ES2),		(IEN  | PTU | DIS | M3)) /*HSUSB1_DATA2*/\
+	MUX_VAL(CP(ETK_D3_ES2),		(IEN  | PTU | DIS | M3)) /*HSUSB1_DATA7*/\
+	MUX_VAL(CP(ETK_D4_ES2),		(IEN  | PTU | DIS | M3)) /*HSUSB1_DATA4*/\
+	MUX_VAL(CP(ETK_D5_ES2),		(IEN  | PTU | DIS | M3)) /*HSUSB1_DATA5*/\
+	MUX_VAL(CP(ETK_D6_ES2),		(IEN  | PTU | DIS | M3)) /*HSUSB1_DATA6*/\
+	MUX_VAL(CP(ETK_D7_ES2),		(IEN  | PTU | DIS | M3)) /*HSUSB1_DATA3*/\
+	MUX_VAL(CP(ETK_D8_ES2),		(IEN  | PTU | DIS | M3)) /*HSUSB1_DIR*/\
+	MUX_VAL(CP(ETK_D9_ES2),		(IEN  | PTU | DIS | M3)) /*HSUSB1_NXT*/\
+	MUX_VAL(CP(ETK_D10_ES2),	(IEN | PTU | EN | M4)) /*GPIO_24*/\
+	MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTU | DIS | M4)) /*GPIO_25*/\
+	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTU | DIS | M4)) /*GPIO_26*/\
+	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTU | DIS | M4)) /*GPIO_27*/\
+	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTU | DIS | M4)) /*GPIO_28*/\
+	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTU | DIS | M4)) /*GPIO_29*/\
+ /*Die to Die */\
+	MUX_VAL(CP(D2D_MCAD1),		(IEN  | PTD | EN  | M0)) /*d2d_mcad1*/\
+	MUX_VAL(CP(D2D_MCAD2),		(IEN  | PTD | EN  | M0)) /*d2d_mcad2*/\
+	MUX_VAL(CP(D2D_MCAD3),		(IEN  | PTD | EN  | M0)) /*d2d_mcad3*/\
+	MUX_VAL(CP(D2D_MCAD4),		(IEN  | PTD | EN  | M0)) /*d2d_mcad4*/\
+	MUX_VAL(CP(D2D_MCAD5),		(IEN  | PTD | EN  | M0)) /*d2d_mcad5*/\
+	MUX_VAL(CP(D2D_MCAD6),		(IEN  | PTD | EN  | M0)) /*d2d_mcad6*/\
+	MUX_VAL(CP(D2D_MCAD7),		(IEN  | PTD | EN  | M0)) /*d2d_mcad7*/\
+	MUX_VAL(CP(D2D_MCAD8),		(IEN  | PTD | EN  | M0)) /*d2d_mcad8*/\
+	MUX_VAL(CP(D2D_MCAD9),		(IEN  | PTD | EN  | M0)) /*d2d_mcad9*/\
+	MUX_VAL(CP(D2D_MCAD10),		(IEN  | PTD | EN  | M0)) /*d2d_mcad10*/\
+	MUX_VAL(CP(D2D_MCAD11),		(IEN  | PTD | EN  | M0)) /*d2d_mcad11*/\
+	MUX_VAL(CP(D2D_MCAD12),		(IEN  | PTD | EN  | M0)) /*d2d_mcad12*/\
+	MUX_VAL(CP(D2D_MCAD13),		(IEN  | PTD | EN  | M0)) /*d2d_mcad13*/\
+	MUX_VAL(CP(D2D_MCAD14),		(IEN  | PTD | EN  | M0)) /*d2d_mcad14*/\
+	MUX_VAL(CP(D2D_MCAD15),		(IEN  | PTD | EN  | M0)) /*d2d_mcad15*/\
+	MUX_VAL(CP(D2D_MCAD16),		(IEN  | PTD | EN  | M0)) /*d2d_mcad16*/\
+	MUX_VAL(CP(D2D_MCAD17),		(IEN  | PTD | EN  | M0)) /*d2d_mcad17*/\
+	MUX_VAL(CP(D2D_MCAD18),		(IEN  | PTD | EN  | M0)) /*d2d_mcad18*/\
+	MUX_VAL(CP(D2D_MCAD19),		(IEN  | PTD | EN  | M0)) /*d2d_mcad19*/\
+	MUX_VAL(CP(D2D_MCAD20),		(IEN  | PTD | EN  | M0)) /*d2d_mcad20*/\
+	MUX_VAL(CP(D2D_MCAD21),		(IEN  | PTD | EN  | M0)) /*d2d_mcad21*/\
+	MUX_VAL(CP(D2D_MCAD22),		(IEN  | PTD | EN  | M0)) /*d2d_mcad22*/\
+	MUX_VAL(CP(D2D_MCAD23),		(IEN  | PTD | EN  | M0)) /*d2d_mcad23*/\
+	MUX_VAL(CP(D2D_MCAD24),		(IEN  | PTD | EN  | M0)) /*d2d_mcad24*/\
+	MUX_VAL(CP(D2D_MCAD25),		(IEN  | PTD | EN  | M0)) /*d2d_mcad25*/\
+	MUX_VAL(CP(D2D_MCAD26),		(IEN  | PTD | EN  | M0)) /*d2d_mcad26*/\
+	MUX_VAL(CP(D2D_MCAD27),		(IEN  | PTD | EN  | M0)) /*d2d_mcad27*/\
+	MUX_VAL(CP(D2D_MCAD28),		(IEN  | PTD | EN  | M0)) /*d2d_mcad28*/\
+	MUX_VAL(CP(D2D_MCAD29),		(IEN  | PTD | EN  | M0)) /*d2d_mcad29*/\
+	MUX_VAL(CP(D2D_MCAD30),		(IEN  | PTD | EN  | M0)) /*d2d_mcad30*/\
+	MUX_VAL(CP(D2D_MCAD31),		(IEN  | PTD | EN  | M0)) /*d2d_mcad31*/\
+	MUX_VAL(CP(D2D_MCAD32),		(IEN  | PTD | EN  | M0)) /*d2d_mcad32*/\
+	MUX_VAL(CP(D2D_MCAD33),		(IEN  | PTD | EN  | M0)) /*d2d_mcad33*/\
+	MUX_VAL(CP(D2D_MCAD34),		(IEN  | PTD | EN  | M0)) /*d2d_mcad34*/\
+	MUX_VAL(CP(D2D_MCAD35),		(IEN  | PTD | EN  | M0)) /*d2d_mcad35*/\
+	MUX_VAL(CP(D2D_MCAD36),		(IEN  | PTD | EN  | M0)) /*d2d_mcad36*/\
+	MUX_VAL(CP(D2D_CLK26MI),	(IEN  | PTD | DIS | M0)) /*d2d_clk26mi*/\
+	MUX_VAL(CP(D2D_NRESPWRON),	(IEN  | PTD | EN  | M0)) /*d2d_nrespwron*/\
+	MUX_VAL(CP(D2D_NRESWARM),	(IEN  | PTU | EN  | M0)) /*d2d_nreswarm */\
+	MUX_VAL(CP(D2D_ARM9NIRQ),	(IEN  | PTD | DIS | M0)) /*d2d_arm9nirq */\
+	MUX_VAL(CP(D2D_UMA2P6FIQ),	(IEN  | PTD | DIS | M0)) /*d2d_uma2p6fiq*/\
+	MUX_VAL(CP(D2D_SPINT),		(IEN  | PTD | EN  | M0)) /*d2d_spint*/\
+	MUX_VAL(CP(D2D_FRINT),		(IEN  | PTD | EN  | M0)) /*d2d_frint*/\
+	MUX_VAL(CP(D2D_DMAREQ0),	(IEN  | PTD | DIS | M0)) /*d2d_dmareq0*/\
+	MUX_VAL(CP(D2D_DMAREQ1),	(IEN  | PTD | DIS | M0)) /*d2d_dmareq1*/\
+	MUX_VAL(CP(D2D_DMAREQ2),	(IEN  | PTD | DIS | M0)) /*d2d_dmareq2*/\
+	MUX_VAL(CP(D2D_DMAREQ3),	(IEN  | PTD | DIS | M0)) /*d2d_dmareq3*/\
+	MUX_VAL(CP(D2D_N3GTRST),	(IEN  | PTD | DIS | M0)) /*d2d_n3gtrst*/\
+	MUX_VAL(CP(D2D_N3GTDI),		(IEN  | PTD | DIS | M0)) /*d2d_n3gtdi*/\
+	MUX_VAL(CP(D2D_N3GTDO),		(IEN  | PTD | DIS | M0)) /*d2d_n3gtdo*/\
+	MUX_VAL(CP(D2D_N3GTMS),		(IEN  | PTD | DIS | M0)) /*d2d_n3gtms*/\
+	MUX_VAL(CP(D2D_N3GTCK),		(IEN  | PTD | DIS | M0)) /*d2d_n3gtck*/\
+	MUX_VAL(CP(D2D_N3GRTCK),	(IEN  | PTD | DIS | M0)) /*d2d_n3grtck*/\
+	MUX_VAL(CP(D2D_MSTDBY),		(IEN  | PTU | EN  | M0)) /*d2d_mstdby*/\
+	MUX_VAL(CP(D2D_SWAKEUP),	(IEN  | PTD | EN  | M0)) /*d2d_swakeup*/\
+	MUX_VAL(CP(D2D_IDLEREQ),	(IEN  | PTD | DIS | M0)) /*d2d_idlereq*/\
+	MUX_VAL(CP(D2D_IDLEACK),	(IEN  | PTU | EN  | M0)) /*d2d_idleack*/\
+	MUX_VAL(CP(D2D_MWRITE),		(IEN  | PTD | DIS | M0)) /*d2d_mwrite*/\
+	MUX_VAL(CP(D2D_SWRITE),		(IEN  | PTD | DIS | M0)) /*d2d_swrite*/\
+	MUX_VAL(CP(D2D_MREAD),		(IEN  | PTD | DIS | M0)) /*d2d_mread*/\
+	MUX_VAL(CP(D2D_SREAD),		(IEN  | PTD | DIS | M0)) /*d2d_sread*/\
+	MUX_VAL(CP(D2D_MBUSFLAG),	(IEN  | PTD | DIS | M0)) /*d2d_mbusflag*/\
+	MUX_VAL(CP(D2D_SBUSFLAG),	(IEN  | PTD | DIS | M0)) /*d2d_sbusflag*/\
+	MUX_VAL(CP(SDRC_CKE0),		(IDIS | PTU | EN  | M0)) /*sdrc_cke0*/\
+	MUX_VAL(CP(SDRC_CKE1),		(IDIS | PTU | EN  | M0)) /*sdrc_cke1*/
+
+#endif
diff --git a/board/matrix_vision/mvblx/sys_eeprom.c b/board/matrix_vision/mvblx/sys_eeprom.c
new file mode 100644
index 0000000000..945a36dfe6
--- /dev/null
+++ b/board/matrix_vision/mvblx/sys_eeprom.c
@@ -0,0 +1,395 @@
+/*
+ * Copyright 2006, 2008-2009, 2011 Freescale Semiconductor
+ * York Sun (yorksun@freescale.com)
+ * Haiying Wang (haiying.wang@freescale.com)
+ * Timur Tabi (timur@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+
+/* #define DEBUG */
+
+/*
+ * static eeprom: EEPROM layout
+ */
+static struct __attribute__ ((__packed__)) eeprom {
+	u8 id[16];		/* 0x01 - 0x0F Type e.g. 100wG-5111 */
+	u8 sn[10];		/* 0x10 - 0x19 Serial Number */
+	u8 date[6];		/* 0x1A - 0x1F Build Date */
+	u8 mac[6];		/* 0x20 - 0x25 MAC address  */
+	u8 reserved[10];/* 0x26 - 0x2f reserved */
+	u32 crc;        /* x+1         CRC32 checksum */
+} e;
+
+/* Set to 1 if we've read EEPROM into memory */
+static int has_been_read;
+
+/**
+ * show_eeprom - display the contents of the EEPROM
+ */
+static void show_eeprom(void)
+{
+	unsigned int crc;
+	char safe_string[16];
+
+#ifdef DEBUG
+	int i;
+#endif
+	u8 *p;
+
+	/* ID */
+	strncpy(safe_string, (char *)e.id, sizeof(e.id));
+	safe_string[sizeof(e.id)-1] = 0;
+	printf("ID: mvBlueLYNX-X%s\n", safe_string);
+
+	/* Serial number */
+	strncpy(safe_string, (char *)e.sn, sizeof(e.sn));
+	safe_string[sizeof(e.sn)-1] = 0;
+	printf("SN: %s\n", safe_string);
+
+	/* Build date, BCD date values, as YYMMDDhhmmss */
+	printf("Build date: 20%02x/%02x/%02x %02x:%02x:%02x %s\n",
+		e.date[0], e.date[1], e.date[2],
+		e.date[3] & 0x7F, e.date[4], e.date[5],
+		e.date[3] & 0x80 ? "PM" : "");
+
+	/* Show MAC address  */
+	p = e.mac;
+	printf("Eth: %02x:%02x:%02x:%02x:%02x:%02x\n",
+		p[0], p[1], p[2], p[3],	p[4], p[5]);
+
+	crc = crc32(0, (void *)&e, sizeof(e) - 4);
+
+	if (crc == be32_to_cpu(e.crc))
+		printf("CRC: %08x\n", be32_to_cpu(e.crc));
+	else
+		printf("CRC: %08x (should be %08x)\n", be32_to_cpu(e.crc), crc);
+
+#ifdef DEBUG
+	printf("EEPROM dump: (0x%x bytes)\n", sizeof(e));
+	for (i = 0; i < sizeof(e); i++) {
+		if ((i % 16) == 0)
+			printf("%02X: ", i);
+		printf("%02X ", ((u8 *)&e)[i]);
+		if (((i % 16) == 15) || (i == sizeof(e) - 1))
+			printf("\n");
+	}
+#endif
+}
+
+/**
+ * read_eeprom - read the EEPROM into memory
+ */
+static int read_eeprom(void)
+{
+	int ret;
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+	unsigned int bus;
+#endif
+
+	if (has_been_read)
+		return 0;
+
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+	bus = i2c_get_bus_num();
+	i2c_set_bus_num(CONFIG_SYS_EEPROM_BUS_NUM);
+#endif
+
+	ret = eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
+		(uchar *)&e, sizeof(e));
+
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+	i2c_set_bus_num(bus);
+#endif
+
+#ifdef DEBUG
+	show_eeprom();
+#endif
+
+	has_been_read = (ret == 0) ? 1 : 0;
+
+	return ret;
+}
+
+/**
+ *  update_crc - update the CRC
+ *
+ *  This function should be called after each update to the EEPROM structure,
+ *  to make sure the CRC is always correct.
+ */
+static void update_crc(void)
+{
+	u32 crc;
+
+	crc = crc32(0, (void *)&e, sizeof(e) - 4);
+	e.crc = cpu_to_be32(crc);
+}
+
+/**
+ * prog_eeprom - write the EEPROM from memory
+ */
+static int prog_eeprom(void)
+{
+	int ret = 0;
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+	unsigned int bus;
+#endif
+
+	update_crc();
+
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+	bus = i2c_get_bus_num();
+	i2c_set_bus_num(CONFIG_SYS_EEPROM_BUS_NUM);
+#endif
+
+	ret = eeprom_write(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
+		(uchar *)&e, sizeof(e));
+
+	if (!ret) {
+		/* Verify the write by reading back the EEPROM and comparing */
+		struct eeprom e2;
+#ifdef DEBUG
+		printf("%s verifying...\n", __func__);
+#endif
+		ret = eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
+			(uchar *)&e2, sizeof(e2));
+
+		if (!ret && memcmp(&e, &e2, sizeof(e)))
+			ret = -1;
+	}
+
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+	i2c_set_bus_num(bus);
+#endif
+
+	if (ret) {
+		printf("Programming failed.\n");
+		has_been_read = 0;
+		return -1;
+	}
+
+	printf("Programming passed.\n");
+	return 0;
+}
+
+/**
+ * h2i - converts hex character into a number
+ *
+ * This function takes a hexadecimal character (e.g. '7' or 'C') and returns
+ * the integer equivalent.
+ */
+static inline u8 h2i(char p)
+{
+	if ((p >= '0') && (p <= '9'))
+		return p - '0';
+
+	if ((p >= 'A') && (p <= 'F'))
+		return (p - 'A') + 10;
+
+	if ((p >= 'a') && (p <= 'f'))
+		return (p - 'a') + 10;
+
+	return 0;
+}
+
+/**
+ * set_date - stores the build date into the EEPROM
+ *
+ * This function takes a pointer to a string in the format "YYMMDDhhmmss"
+ * (2-digit year, 2-digit month, etc), converts it to a 6-byte BCD string,
+ * and stores it in the build date field of the EEPROM local copy.
+ */
+static void set_date(const char *string)
+{
+	unsigned int i;
+
+	if (strlen(string) != 12) {
+		printf("Usage: mac date YYMMDDhhmmss\n");
+		return;
+	}
+
+	for (i = 0; i < 6; i++)
+		e.date[i] = h2i(string[2 * i]) << 4 | h2i(string[2 * i + 1]);
+
+	update_crc();
+}
+
+/**
+ * set_mac_address - stores a MAC address into the EEPROM
+ *
+ * This function takes a pointer to MAC address string
+ * (i.e."XX:XX:XX:XX:XX:XX", where "XX" is a two-digit hex number) and
+ * stores it in the MAC address field in the EEPROM local copy.
+ */
+static void set_mac_address(const char *string)
+{
+	char *p = (char *) string;
+	unsigned int i;
+
+	for (i = 0; *p && (i < 6); i++) {
+		e.mac[i] = simple_strtoul(p, &p, 16);
+		if (*p == ':')
+			p++;
+	}
+
+	update_crc();
+}
+
+int do_mac(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+	char cmd;
+
+	if (argc == 1) {
+		show_eeprom();
+		return 0;
+	}
+
+	cmd = argv[1][0];
+
+	if (cmd == 'r') {
+#ifdef DEBUG
+		printf("%s read\n", __func__);
+#endif
+		read_eeprom();
+		return 0;
+	}
+
+	if (argc == 2) {
+		switch (cmd) {
+		case 's':	/* save */
+#ifdef DEBUG
+			printf("%s save\n", __func__);
+#endif
+			prog_eeprom();
+			break;
+		default:
+			return cmd_usage(cmdtp);
+		}
+
+		return 0;
+	}
+
+	/* We know we have at least one parameter  */
+
+	switch (cmd) {
+	case 'n':	/* serial number */
+#ifdef DEBUG
+		printf("%s serial number\n", __func__);
+#endif
+		memset(e.sn, 0, sizeof(e.sn));
+		strncpy((char *)e.sn, argv[2], sizeof(e.sn) - 1);
+		update_crc();
+		break;
+	case 'd':	/* date BCD format YYMMDDhhmmss */
+		set_date(argv[2]);
+		break;
+	case 'e':	/* errata */
+		printf("mac errata not implemented\n");
+		break;
+	case 'i':	/* id */
+		memset(e.id, 0, sizeof(e.id));
+		strncpy((char *)e.id, argv[2], sizeof(e.id) - 1);
+		update_crc();
+		break;
+	case 'p':	/* ports */
+		printf("mac ports not implemented (always 1 port)\n");
+		break;
+	case '0' ... '9':
+		/* we only have "mac 0" but any digit can be used here */
+		set_mac_address(argv[2]);
+		break;
+	case 'h':	/* help */
+	default:
+		return cmd_usage(cmdtp);
+	}
+
+	return 0;
+}
+
+int mac_read_from_eeprom(void)
+{
+	u32 crc, crc_offset = offsetof(struct eeprom, crc);
+	u32 *crcp; /* Pointer to the CRC in the data read from the EEPROM */
+
+	if (read_eeprom()) {
+		printf("EEPROM Read failed.\n");
+		return -1;
+	}
+
+	crc = crc32(0, (void *)&e, crc_offset);
+	crcp = (void *)&e + crc_offset;
+	if (crc != be32_to_cpu(*crcp)) {
+		printf("EEPROM CRC mismatch (%08x != %08x)\n", crc,
+			be32_to_cpu(e.crc));
+		return -1;
+	}
+
+	if (memcmp(&e.mac, "\0\0\0\0\0\0", 6) &&
+		memcmp(&e.mac, "\xFF\xFF\xFF\xFF\xFF\xFF", 6)) {
+		char ethaddr[9];
+
+		sprintf(ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X",
+			e.mac[0],
+			e.mac[1],
+			e.mac[2],
+			e.mac[3],
+			e.mac[4],
+			e.mac[5]);
+		/* Only initialize environment variables that are blank
+		 * (i.e. have not yet been set)
+		 */
+		if (!getenv("ethaddr"))
+			setenv("ethaddr", ethaddr);
+	}
+
+	if (memcmp(&e.sn, "\0\0\0\0\0\0\0\0\0\0", 10) &&
+		memcmp(&e.sn, "\xFF\xFF\xFF\xFF\xFF\xFF\xFF\xFF\xFF\xFF", 10)) {
+		char serial_num[12];
+
+		strncpy(serial_num, (char *)e.sn, sizeof(e.sn) - 1);
+		/* Only initialize environment variables that are blank
+		 * (i.e. have not yet been set)
+		 */
+		if (!getenv("serial#"))
+			setenv("serial#", serial_num);
+	}
+
+	/* TODO should I calculate CRC here? */
+	return 0;
+}
+
+#ifdef CONFIG_SERIAL_TAG
+void get_board_serial(struct tag_serialnr *serialnr)
+{
+	char *serial = getenv("serial#");
+
+	if (serial && (strlen(serial) > 3)) {
+		/* use the numerical part of the serial number LXnnnnnn */
+		serialnr->high = 0;
+		serialnr->low = simple_strtoul(serial + 2, NULL, 10);
+	} else {
+		serialnr->high = 0;
+		serialnr->low = 0;
+	}
+}
+#endif
diff --git a/board/samsung/origen/Makefile b/board/samsung/origen/Makefile
index bb6eaf6fa4..3a885a5cdb 100644
--- a/board/samsung/origen/Makefile
+++ b/board/samsung/origen/Makefile
@@ -41,7 +41,7 @@ OBJS	:= $(addprefix $(obj),$(COBJS) $(SOBJS))
 ALL	+=$(obj).depend $(LIB)
 
 ifdef CONFIG_SPL_BUILD
-ALL	+= tools/mk$(BOARD)spl.exe
+ALL	+= $(OBJTREE)/tools/mk$(BOARD)spl
 endif
 
 all:	$(ALL)
@@ -50,8 +50,8 @@ $(LIB):	$(OBJS)
 	$(call cmd_link_o_target, $(OBJS))
 
 ifdef CONFIG_SPL_BUILD
-tools/mk$(BOARD)spl.exe:	tools/mkv310_image.c
-	$(HOSTCC) tools/mkv310_image.c -o tools/mk$(BOARD)spl.exe
+$(OBJTREE)/tools/mk$(BOARD)spl:	tools/mkv310_image.c
+	$(HOSTCC) tools/mkv310_image.c -o $(OBJTREE)/tools/mk$(BOARD)spl
 endif
 
 #########################################################################
diff --git a/board/samsung/smdkv310/Makefile b/board/samsung/smdkv310/Makefile
index d168abd11d..56e0c16eb7 100644
--- a/board/samsung/smdkv310/Makefile
+++ b/board/samsung/smdkv310/Makefile
@@ -26,16 +26,33 @@ LIB	= $(obj)lib$(BOARD).o
 
 SOBJS	:= mem_setup.o
 SOBJS	+= lowlevel_init.o
+ifndef CONFIG_SPL_BUILD
 COBJS	+= smdkv310.o
+endif
+
+ifdef CONFIG_SPL_BUILD
+COBJS	+= mmc_boot.o
+endif
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS) $(SOBJS))
 
-all:	 $(obj).depend $(LIB)
+ALL	:=	 $(obj).depend $(LIB)
+
+ifdef CONFIG_SPL_BUILD
+ALL	+= $(OBJTREE)/tools/mk$(BOARD)spl
+endif
+
+all:	$(ALL)
 
 $(LIB):	$(OBJS)
 	$(call cmd_link_o_target, $(OBJS))
 
+ifdef CONFIG_SPL_BUILD
+$(OBJTREE)/tools/mk$(BOARD)spl:	tools/mkv310_image.c
+	$(HOSTCC) tools/mkv310_image.c -o $(OBJTREE)/tools/mk$(BOARD)spl
+endif
+
 #########################################################################
 
 # defines $(obj).depend target
diff --git a/board/samsung/smdkv310/mmc_boot.c b/board/samsung/smdkv310/mmc_boot.c
new file mode 100644
index 0000000000..d3fc18d19f
--- /dev/null
+++ b/board/samsung/smdkv310/mmc_boot.c
@@ -0,0 +1,60 @@
+/*
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include<common.h>
+#include<config.h>
+
+/*
+* Copy U-boot from mmc to RAM:
+* COPY_BL2_FNPTR_ADDR: Address in iRAM, which Contains
+* API (Data transfer from mmc to ram)
+*/
+void copy_uboot_to_ram(void)
+{
+	u32 (*copy_bl2)(u32, u32, u32) = (void *)COPY_BL2_FNPTR_ADDR;
+
+	copy_bl2(BL2_START_OFFSET, BL2_SIZE_BLOC_COUNT, CONFIG_SYS_TEXT_BASE);
+}
+
+void board_init_f(unsigned long bootflag)
+{
+	__attribute__((noreturn)) void (*uboot)(void);
+	copy_uboot_to_ram();
+
+	/* Jump to U-Boot image */
+	uboot = (void *)CONFIG_SYS_TEXT_BASE;
+	(*uboot)();
+	/* Never returns Here */
+}
+
+/* Place Holders */
+void board_init_r(gd_t *id, ulong dest_addr)
+{
+	/*Function attribute is no-return*/
+	/*This Function never executes*/
+	while (1)
+		;
+}
+
+void save_boot_params(u32 r0, u32 r1, u32 r2, u32 r3)
+{
+}
diff --git a/board/samsung/smdkv310/smdkv310.c b/board/samsung/smdkv310/smdkv310.c
index e0b89dd55b..d9caca7f18 100644
--- a/board/samsung/smdkv310/smdkv310.c
+++ b/board/samsung/smdkv310/smdkv310.c
@@ -57,7 +57,6 @@ int board_init(void)
 
 	smc9115_pre_init();
 
-	gd->bd->bi_arch_number = MACH_TYPE_SMDKV310;
 	gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
 	return 0;
 }
@@ -75,13 +74,17 @@ int dram_init(void)
 void dram_init_banksize(void)
 {
 	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+	gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1, \
+							PHYS_SDRAM_1_SIZE);
 	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
-	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+	gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2, \
+							PHYS_SDRAM_2_SIZE);
 	gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
-	gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE;
+	gd->bd->bi_dram[2].size = get_ram_size((long *)PHYS_SDRAM_3, \
+							PHYS_SDRAM_3_SIZE);
 	gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
-	gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE;
+	gd->bd->bi_dram[3].size = get_ram_size((long *)PHYS_SDRAM_4, \
+							PHYS_SDRAM_4_SIZE);
 }
 
 int board_eth_init(bd_t *bis)
diff --git a/board/samsung/smdkv310/tools/mkv310_image.c b/board/samsung/smdkv310/tools/mkv310_image.c
new file mode 100644
index 0000000000..1a51913f59
--- /dev/null
+++ b/board/samsung/smdkv310/tools/mkv310_image.c
@@ -0,0 +1,117 @@
+/*
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <stdio.h>
+#include <stdlib.h>
+#include <unistd.h>
+#include <fcntl.h>
+#include <errno.h>
+#include <string.h>
+#include <sys/stat.h>
+
+#define CHECKSUM_OFFSET		(14*1024-4)
+#define BUFSIZE			(16*1024)
+#define FILE_PERM		(S_IRUSR | S_IWUSR | S_IRGRP \
+				| S_IWGRP | S_IROTH | S_IWOTH)
+/*
+* Requirement:
+* IROM code reads first 14K bytes from boot device.
+* It then calculates the checksum of 14K-4 bytes and compare with data at
+* 14K-4 offset.
+*
+* This function takes two filenames:
+* IN  "u-boot-spl.bin" and
+* OUT "u-boot-mmc-spl.bin" as filenames.
+* It reads the "u-boot-spl.bin" in 16K buffer.
+* It calculates checksum of 14K-4 Bytes and stores at 14K-4 offset in buffer.
+* It writes the buffer to "u-boot-mmc-spl.bin" file.
+*/
+
+int main(int argc, char **argv)
+{
+	int i, len;
+	unsigned char buffer[BUFSIZE] = {0};
+	int ifd, ofd;
+	unsigned int checksum = 0, count;
+
+	if (argc != 3) {
+		printf(" %d Wrong number of arguments\n", argc);
+		exit(EXIT_FAILURE);
+	}
+
+	ifd = open(argv[1], O_RDONLY);
+	if (ifd < 0) {
+		fprintf(stderr, "%s: Can't open %s: %s\n",
+			argv[0], argv[1], strerror(errno));
+		exit(EXIT_FAILURE);
+	}
+
+	ofd = open(argv[2], O_WRONLY | O_CREAT | O_TRUNC, FILE_PERM);
+	if (ifd < 0) {
+		fprintf(stderr, "%s: Can't open %s: %s\n",
+			argv[0], argv[2], strerror(errno));
+		if (ifd)
+			close(ifd);
+		exit(EXIT_FAILURE);
+	}
+
+	len = lseek(ifd, 0, SEEK_END);
+	lseek(ifd, 0, SEEK_SET);
+
+	count = (len < CHECKSUM_OFFSET) ? len : CHECKSUM_OFFSET;
+
+	if (read(ifd, buffer, count) != count) {
+		fprintf(stderr, "%s: Can't read %s: %s\n",
+			argv[0], argv[1], strerror(errno));
+
+		if (ifd)
+			close(ifd);
+		if (ofd)
+			close(ofd);
+
+		exit(EXIT_FAILURE);
+	}
+
+	for (i = 0, checksum = 0; i < CHECKSUM_OFFSET; i++)
+		checksum += buffer[i];
+
+	memcpy(&buffer[CHECKSUM_OFFSET], &checksum, sizeof(checksum));
+
+	if (write(ofd, buffer, BUFSIZE) != BUFSIZE) {
+		fprintf(stderr, "%s: Can't write %s: %s\n",
+			argv[0], argv[2], strerror(errno));
+
+		if (ifd)
+			close(ifd);
+		if (ofd)
+			close(ofd);
+
+		exit(EXIT_FAILURE);
+	}
+
+	if (ifd)
+		close(ifd);
+	if (ofd)
+		close(ofd);
+
+	return EXIT_SUCCESS;
+}
diff --git a/board/samsung/universal_c210/universal.c b/board/samsung/universal_c210/universal.c
index 1b27e8b428..d767eaac49 100644
--- a/board/samsung/universal_c210/universal.c
+++ b/board/samsung/universal_c210/universal.c
@@ -27,6 +27,7 @@
 #include <asm/arch/adc.h>
 #include <asm/arch/gpio.h>
 #include <asm/arch/mmc.h>
+#include <pmic.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -57,6 +58,10 @@ int board_init(void)
 	check_hw_revision();
 	printf("HW Revision:\t0x%x\n", board_rev);
 
+#if defined(CONFIG_PMIC)
+	pmic_init();
+#endif
+
 	return 0;
 }
 
diff --git a/board/syteco/jadecpu/jadecpu.c b/board/syteco/jadecpu/jadecpu.c
index 63a0d33446..72288fe4e8 100644
--- a/board/syteco/jadecpu/jadecpu.c
+++ b/board/syteco/jadecpu/jadecpu.c
@@ -40,7 +40,6 @@ int board_init(void)
 	writel(0x00000010, &ccnt->cmux_md);
 
 	gd->flags = 0;
-	gd->bd->bi_arch_number = MACH_TYPE_JADECPU;
 	gd->bd->bi_boot_params = PHYS_SDRAM + PHYS_SDRAM_SIZE - 0x10000;
 
 	icache_enable();
diff --git a/board/ti/evm/evm.c b/board/ti/evm/evm.c
index b17c0fbadf..8c434633dd 100644
--- a/board/ti/evm/evm.c
+++ b/board/ti/evm/evm.c
@@ -217,7 +217,22 @@ int board_eth_init(bd_t *bis)
 {
 	int rc = 0;
 #ifdef CONFIG_SMC911X
+#define STR_ENV_ETHADDR	"ethaddr"
+
+	struct eth_device *dev;
+	uchar eth_addr[6];
+
 	rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
+
+	if (!eth_getenv_enetaddr(STR_ENV_ETHADDR, eth_addr)) {
+		dev = eth_get_dev_by_index(0);
+		if (dev) {
+			eth_setenv_enetaddr(STR_ENV_ETHADDR, dev->enetaddr);
+		} else {
+			printf("omap3evm: Couldn't get eth device\n");
+			rc = -1;
+		}
+	}
 #endif
 	return rc;
 }
diff --git a/board/ttcontrol/vision2/vision2.c b/board/ttcontrol/vision2/vision2.c
index d3815b2eed..f556d308e3 100644
--- a/board/ttcontrol/vision2/vision2.c
+++ b/board/ttcontrol/vision2/vision2.c
@@ -31,7 +31,6 @@
 #include <asm/arch/iomux.h>
 #include <asm/gpio.h>
 #include <asm/arch/sys_proto.h>
-#include <asm/errno.h>
 #include <i2c.h>
 #include <mmc.h>
 #include <pmic.h>
@@ -44,8 +43,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-static u32 system_rev;
-
 static struct fb_videomode nec_nl6448bc26_09c = {
 	"NEC_NL6448BC26-09C",
 	60,	/* Refresh */
@@ -151,13 +148,6 @@ static void init_drive_strength(void)
 		PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST);
 }
 
-u32 get_board_rev(void)
-{
-	system_rev = get_cpu_rev();
-
-	return system_rev;
-}
-
 int dram_init(void)
 {
 	gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1,