powerpc/t1024rdb: Add T1024 RDB board support

T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.

T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
  - Two 10M/100M/1G RGMII ports on-board
  - one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two  Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
	   Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>

1 files changed, 117 insertions, 0 deletions

diff --git a/board/freescale/t102xrdb/tlb.c b/board/freescale/t102xrdb/tlb.c
new file mode 100644
index 0000000000..8269b3d725
--- /dev/null
+++ b/board/freescale/t102xrdb/tlb.c
@@ -0,0 +1,117 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+	/* TLB 0 - for temp stack in cache */
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+
+	/* TLB 1 */
+	/* *I*** - Covers boot page */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+	/*
+	 * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the
+	 * SRAM is at 0xfffc0000, it covered the 0xfffff000.
+	 */
+	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 0, BOOKE_PAGESZ_256K, 1),
+#else
+	SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 0, BOOKE_PAGESZ_4K, 1),
+#endif
+
+	/* *I*G* - CCSRBAR */
+	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 1, BOOKE_PAGESZ_16M, 1),
+
+	/* *I*G* - Flash, localbus */
+	/* This will be changed to *I*G* after relocation to RAM. */
+	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+		      MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+		      0, 2, BOOKE_PAGESZ_256M, 1),
+
+#ifndef CONFIG_SPL_BUILD
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 3, BOOKE_PAGESZ_1G, 1),
+
+	/* *I*G* - PCI I/O */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 4, BOOKE_PAGESZ_256K, 1),
+
+	/* Bman/Qman */
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 5, BOOKE_PAGESZ_16M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
+		      CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 6, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 7, BOOKE_PAGESZ_16M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
+		      CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 8, BOOKE_PAGESZ_16M, 1),
+#endif
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 9, BOOKE_PAGESZ_4M, 1),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE
+	SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 10, BOOKE_PAGESZ_64K, 1),
+#endif
+#ifdef CONFIG_SYS_CPLD_BASE
+	SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 11, BOOKE_PAGESZ_256K, 1),
+#endif
+
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 12, BOOKE_PAGESZ_1G, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+		      CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 13, BOOKE_PAGESZ_1G, 1)
+#endif
+	/* entry 14 and 15 has been used hard coded, they will be disabled
+	 * in cpu_init_f, so if needed more, will use entry 16 later.
+	 */
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);