imx: mx6qpsabreauto: Add MX6QP SABREAUTO CPU3 board support

1. Add DDR script for mx6qpsabreauto board.
2. On CPU3 board, enet RGMII tx clock is from internal PLL. Set the GPR5[9]
   and init the enet pll output to 125Mhz.
3. On CPU3 board, SW1ABC=VDDSOC_IN, SW2=VDDARM_IN.

Build target: mx6qpsabreauto_config

Boot Log:
U-Boot 2015.07-rc2-00071-gfd985ff (Jun 29 2015 - 22:10:55 +0800)

CPU:   Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz)
CPU:   Automotive temperature grade (-40C to 125C) at 34C
Reset cause: POR
Board: MX6Q-Sabreauto revA
I2C:   ready
DRAM:  2 GiB
PMIC:  PFUZE100 ID=0x10
Flash: 32 MiB
NAND:  0 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

No panel detected: default to HDMI
Display: HDMI (1024x768)
In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0

Note:
In this patch, we still add a new config mx6qpsabreauto_config,
since SPL is not supported now, and IMX_CONFIG is needed at
build time, so add this config. Future, when SPL is converted,
this config can be removed.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>

1 files changed, 145 insertions, 0 deletions

diff --git a/board/freescale/mx6qsabreauto/mx6qp.cfg b/board/freescale/mx6qsabreauto/mx6qp.cfg
new file mode 100644
index 0000000000..2298c772cc
--- /dev/null
+++ b/board/freescale/mx6qsabreauto/mx6qp.cfg
@@ -0,0 +1,145 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+/* image version */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of spi, sd, eimnor, nand, sata:
+ * spinor: flash_offset: 0x0400
+ * nand:   flash_offset: 0x0400
+ * sata:   flash_offset: 0x0400
+ * sd/mmc: flash_offset: 0x0400
+ * eimnor: flash_offset: 0x1000
+ */
+BOOT_FROM	sd
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+DATA 4 0x020e0798 0x000C0000
+DATA 4 0x020e0758 0x00000000
+DATA 4 0x020e0588 0x00000030
+DATA 4 0x020e0594 0x00000030
+DATA 4 0x020e056c 0x00000030
+DATA 4 0x020e0578 0x00000030
+DATA 4 0x020e074c 0x00000030
+DATA 4 0x020e057c 0x00000030
+DATA 4 0x020e058c 0x00000000
+DATA 4 0x020e059c 0x00000030
+DATA 4 0x020e05a0 0x00000030
+DATA 4 0x020e078c 0x00000030
+DATA 4 0x020e0750 0x00020000
+DATA 4 0x020e05a8 0x00000030
+DATA 4 0x020e05b0 0x00000030
+DATA 4 0x020e0524 0x00000030
+DATA 4 0x020e051c 0x00000030
+DATA 4 0x020e0518 0x00000030
+DATA 4 0x020e050c 0x00000030
+DATA 4 0x020e05b8 0x00000030
+DATA 4 0x020e05c0 0x00000030
+DATA 4 0x020e0774 0x00020000
+DATA 4 0x020e0784 0x00000030
+DATA 4 0x020e0788 0x00000030
+DATA 4 0x020e0794 0x00000030
+DATA 4 0x020e079c 0x00000030
+DATA 4 0x020e07a0 0x00000030
+DATA 4 0x020e07a4 0x00000030
+DATA 4 0x020e07a8 0x00000030
+DATA 4 0x020e0748 0x00000030
+DATA 4 0x020e05ac 0x00000030
+DATA 4 0x020e05b4 0x00000030
+DATA 4 0x020e0528 0x00000030
+DATA 4 0x020e0520 0x00000030
+DATA 4 0x020e0514 0x00000030
+DATA 4 0x020e0510 0x00000030
+DATA 4 0x020e05bc 0x00000030
+DATA 4 0x020e05c4 0x00000030
+DATA 4 0x021b0800 0xa1390003
+DATA 4 0x021b080c 0x001b001e
+DATA 4 0x021b0810 0x002e0029
+DATA 4 0x021b480c 0x001b002a
+DATA 4 0x021b4810 0x0019002c
+DATA 4 0x021b083c 0x43240334
+DATA 4 0x021b0840 0x0324031a
+DATA 4 0x021b483c 0x43340344
+DATA 4 0x021b4840 0x03280276
+DATA 4 0x021b0848 0x44383A3E
+DATA 4 0x021b4848 0x3C3C3846
+DATA 4 0x021b0850 0x2e303230
+DATA 4 0x021b4850 0x38283E34
+DATA 4 0x021b081c 0x33333333
+DATA 4 0x021b0820 0x33333333
+DATA 4 0x021b0824 0x33333333
+DATA 4 0x021b0828 0x33333333
+DATA 4 0x021b481c 0x33333333
+DATA 4 0x021b4820 0x33333333
+DATA 4 0x021b4824 0x33333333
+DATA 4 0x021b4828 0x33333333
+DATA 4 0x021b08c0 0x24912492
+DATA 4 0x021b48c0 0x24912492
+DATA 4 0x021b08b8 0x00000800
+DATA 4 0x021b48b8 0x00000800
+DATA 4 0x021b0004 0x00020036
+DATA 4 0x021b0008 0x09444040
+DATA 4 0x021b000c 0x898E7955
+DATA 4 0x021b0010 0xFF328F64
+DATA 4 0x021b0014 0x01FF00DB
+DATA 4 0x021b0018 0x00001740
+DATA 4 0x021b001c 0x00008000
+
+DATA 4 0x021b002c 0x000026d2
+DATA 4 0x021b0030 0x008E1023
+DATA 4 0x021b0040 0x00000047
+DATA 4 0x021b0400 0x14420000
+DATA 4 0x021b0000 0x841A0000
+DATA 4 0x00bb0008 0x00000004
+DATA 4 0x00bb000c 0x2891E41A
+DATA 4 0x00bb0038 0x00000564
+DATA 4 0x00bb0014 0x00000040
+DATA 4 0x00bb0028 0x00000020
+DATA 4 0x00bb002c 0x00000020
+DATA 4 0x021b001c 0x04088032
+DATA 4 0x021b001c 0x00008033
+DATA 4 0x021b001c 0x00048031
+DATA 4 0x021b001c 0x09408030
+DATA 4 0x021b001c 0x04008040
+DATA 4 0x021b0020 0x00005800
+DATA 4 0x021b0818 0x00011117
+DATA 4 0x021b4818 0x00011117
+DATA 4 0x021b0004 0x00025576
+DATA 4 0x021b0404 0x00011006
+DATA 4 0x021b001c 0x00000000
+/* set the default clock gate to save power */
+DATA 4, 0x020c4068, 0x00C03F3F
+DATA 4, 0x020c406c, 0x0030FC03
+DATA 4, 0x020c4070, 0x0FFFC000
+DATA 4, 0x020c4074, 0x3FF00000
+DATA 4, 0x020c4078, 0xFFFFF300
+DATA 4, 0x020c407c, 0x0F0000F3
+DATA 4, 0x020c4080, 0x00000FFF
+
+/* enable AXI cache for VDOA/VPU/IPU */
+DATA 4, 0x020e0010, 0xF00000CF
+/* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */
+DATA 4, 0x020e0018, 0x77177717
+DATA 4, 0x020e001c, 0x77177717