[PPC440SPe] Improve PCIe configuration space access

- correct configuration space mapping
- correct bus numbering
- better access to config space

Prior to this patch, the 440SPe host/PCIe bridge was able to configure only the
first device on the first bus. We now allow to configure up to 16 buses;
also, scanning for devices behind the PCIe-PCIe bridge is supported, so
peripheral devices farther in hierarchy can be identified.

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>

2 files changed, 11 insertions, 10 deletions

diff --git a/board/amcc/yucca/init.S b/board/amcc/yucca/init.S
index c92dcf7a51..67e8f8f3a2 100644
--- a/board/amcc/yucca/init.S
+++ b/board/amcc/yucca/init.S
@@ -70,9 +70,9 @@ tlbtabA:
 	tlbentry(CFG_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_R|AC_W|SA_G|SA_I)
 	tlbentry(CFG_PCIE_BASE, SZ_16K, 0x20000000, 0xC, AC_R|AC_W|SA_G|SA_I)
 
-	tlbentry(CFG_PCIE0_CFGBASE, SZ_1K, 0x40000000, 0xC, AC_R|AC_W|SA_G|SA_I)
-	tlbentry(CFG_PCIE1_CFGBASE, SZ_1K, 0x80000000, 0xC, AC_R|AC_W|SA_G|SA_I)
-	tlbentry(CFG_PCIE2_CFGBASE, SZ_1K, 0xC0000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE0_CFGBASE, SZ_16M, 0x40000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE1_CFGBASE, SZ_16M, 0x80000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE2_CFGBASE, SZ_16M, 0xC0000000, 0xC, AC_R|AC_W|SA_G|SA_I)
 	tlbentry(CFG_PCIE0_XCFGBASE, SZ_1K, 0x50000000, 0xC, AC_R|AC_W|SA_G|SA_I)
 	tlbentry(CFG_PCIE1_XCFGBASE, SZ_1K, 0x90000000, 0xC, AC_R|AC_W|SA_G|SA_I)
 	tlbentry(CFG_PCIE2_XCFGBASE, SZ_1K, 0xD0000000, 0xC, AC_R|AC_W|SA_G|SA_I)
@@ -112,9 +112,9 @@ tlbtabB:
 	tlbentry(CFG_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_R|AC_W|SA_G|SA_I)
 	tlbentry(CFG_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_R|AC_W|SA_G|SA_I)
 
-	tlbentry(CFG_PCIE0_CFGBASE, SZ_1K, 0x00100000, 0xD, AC_R|AC_W|SA_G|SA_I)
-	tlbentry(CFG_PCIE1_CFGBASE, SZ_1K, 0x20100000, 0xD, AC_R|AC_W|SA_G|SA_I)
-	tlbentry(CFG_PCIE2_CFGBASE, SZ_1K, 0x40100000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE0_CFGBASE, SZ_16M, 0x00000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE1_CFGBASE, SZ_16M, 0x20000000, 0xD, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCIE2_CFGBASE, SZ_16M, 0x40000000, 0xD, AC_R|AC_W|SA_G|SA_I)
 	tlbentry(CFG_PCIE0_XCFGBASE, SZ_1K, 0x10000000, 0xD, AC_R|AC_W|SA_G|SA_I)
 	tlbentry(CFG_PCIE1_XCFGBASE, SZ_1K, 0x30000000, 0xD, AC_R|AC_W|SA_G|SA_I)
 	tlbentry(CFG_PCIE2_XCFGBASE, SZ_1K, 0x50000000, 0xD, AC_R|AC_W|SA_G|SA_I)
diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c
index d08fcf3565..252e4fe07a 100644
--- a/board/amcc/yucca/yucca.c
+++ b/board/amcc/yucca/yucca.c
@@ -846,7 +846,7 @@ void yucca_setup_pcie_fpga_endpoint(int port)
 
 static struct pci_controller pcie_hose[3] = {{0},{0},{0}};
 
-void pcie_setup_hoses(void)
+void pcie_setup_hoses(int busno)
 {
 	struct pci_controller *hose;
 	int i, bus;
@@ -855,7 +855,7 @@ void pcie_setup_hoses(void)
 	 * assume we're called after the PCIX hose is initialized, which takes
 	 * bus ID 0 and therefore start numbering PCIe's from 1.
 	 */
-	bus = 1;
+	bus = busno;
 	for (i = 0; i <= 2; i++) {
 		/* Check for yucca card presence */
 		if (!yucca_pcie_card_present(i))
@@ -874,8 +874,8 @@ void pcie_setup_hoses(void)
 
 		hose = &pcie_hose[i];
 		hose->first_busno = bus;
-		hose->last_busno  = bus;
-		bus++;
+		hose->last_busno = bus;
+		hose->current_busno = bus;
 
 		/* setup mem resource */
 		pci_set_region(hose->regions + 0,
@@ -899,6 +899,7 @@ void pcie_setup_hoses(void)
 		 * Config access can only go down stream
 		 */
 		hose->last_busno = pci_hose_scan(hose);
+		bus = hose->last_busno + 1;
 #endif
 	}
 }