Add support for Seagate BlackArmor NAS220

Add support for Seagate BlackArmor NAS220

Signed-off-by: Evgeni Dobrev <evgeni@studio-punkt.com>

1 files changed, 118 insertions, 0 deletions

diff --git a/board/Seagate/nas220/nas220.c b/board/Seagate/nas220/nas220.c
new file mode 100644
index 0000000000..d9a06273a3
--- /dev/null
+++ b/board/Seagate/nas220/nas220.c
@@ -0,0 +1,118 @@
+/*
+ * Copyright (C) 2014  Evgeni Dobrev <evgeni@studio-punkt.com>
+ *
+ * Based on sheevaplug.c originally written by
+ * Prafulla Wadaskar <prafulla@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/soc.h>
+#include <asm/arch/mpp.h>
+#include <asm/arch/cpu.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+	/*
+	 * default gpio configuration
+	 */
+	mvebu_config_gpio(NAS220_GE_OE_VAL_LOW, NAS220_GE_OE_VAL_HIGH,
+			  NAS220_GE_OE_LOW, NAS220_GE_OE_HIGH);
+
+	/* Multi-Purpose Pins Functionality configuration */
+	static const u32 kwmpp_config[] = {
+		MPP0_NF_IO2,
+		MPP1_NF_IO3,
+		MPP2_NF_IO4,
+		MPP3_NF_IO5,
+		MPP4_NF_IO6,
+		MPP5_NF_IO7,
+		MPP6_SYSRST_OUTn,
+		MPP7_SPI_SCn,
+		MPP8_TW_SDA,
+		MPP9_TW_SCK,
+		MPP10_UART0_TXD,
+		MPP11_UART0_RXD,
+		MPP12_GPO,
+		MPP13_GPIO,
+		MPP14_GPIO,
+		MPP15_SATA0_ACTn,
+		MPP16_SATA1_ACTn,
+		MPP17_SATA0_PRESENTn,
+		MPP18_NF_IO0,
+		MPP19_NF_IO1,
+		MPP20_GPIO,
+		MPP21_GPIO,
+		MPP22_GPIO,
+		MPP23_GPIO,
+		MPP24_GPIO,
+		MPP25_GPIO,
+		MPP26_GPIO,
+		MPP27_GPIO,
+		MPP28_GPIO,
+		MPP29_GPIO,
+		MPP30_GPIO,
+		MPP31_GPIO,
+		MPP32_GPIO,
+		MPP33_GPIO,
+		MPP34_GPIO,
+		MPP35_GPIO,
+		0
+	};
+	kirkwood_mpp_conf(kwmpp_config, NULL);
+	return 0;
+}
+
+int board_init(void)
+{
+	/*
+	 * arch number of board
+	 */
+	gd->bd->bi_arch_number = MACH_TYPE_NAS220;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+	return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1116 PHY */
+void reset_phy(void)
+{
+	u16 reg;
+	u16 devadr;
+	char *name = "egiga0";
+
+	if (miiphy_set_current_dev(name))
+		return;
+
+	/* command to read PHY dev address */
+	if (miiphy_read(name, 0xEE, 0xEE, (u16 *)&devadr)) {
+		printf("Err..%s could not read PHY dev address\n", __func__);
+		return;
+	}
+
+	/*
+	 * Enable RGMII delay on Tx and Rx for CPU port
+	 * Ref: sec 4.7.2 of chip datasheet
+	 */
+	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+	miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
+	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+	miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+	/* reset the phy */
+	miiphy_reset(name, devadr);
+
+	printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */