ARM: remove cm4008 and cm41xx board support

These are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Greg Ungerer <greg.ungerer@opengear.com>
Acked-by: Marek Vasut <marex@denx.de>

4 files changed, 0 insertions, 276 deletions

diff --git a/arch/arm/cpu/arm920t/Makefile b/arch/arm/cpu/arm920t/Makefile
index a16838b479..29a350c9a6 100644
--- a/arch/arm/cpu/arm920t/Makefile
+++ b/arch/arm/cpu/arm920t/Makefile
@@ -13,5 +13,4 @@ obj-$(CONFIG_USE_IRQ)	+= interrupts.o
 obj-$(if $(filter a320,$(SOC)),y) += a320/
 obj-$(CONFIG_EP93XX) += ep93xx/
 obj-$(CONFIG_IMX) += imx/
-obj-$(CONFIG_KS8695) += ks8695/
 obj-$(CONFIG_S3C24X0) += s3c24x0/
diff --git a/arch/arm/cpu/arm920t/ks8695/Makefile b/arch/arm/cpu/arm920t/ks8695/Makefile
deleted file mode 100644
index 400aa89e99..0000000000
--- a/arch/arm/cpu/arm920t/ks8695/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	= lowlevel_init.o
-obj-y	+= timer.o
diff --git a/arch/arm/cpu/arm920t/ks8695/lowlevel_init.S b/arch/arm/cpu/arm920t/ks8695/lowlevel_init.S
deleted file mode 100644
index a2a07f2f23..0000000000
--- a/arch/arm/cpu/arm920t/ks8695/lowlevel_init.S
+++ /dev/null
@@ -1,189 +0,0 @@
-/*
- *  lowlevel_init.S - basic hardware initialization for the KS8695 CPU
- *
- *  Copyright (c) 2004-2005, Greg Ungerer <greg.ungerer@opengear.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <config.h>
-#include <version.h>
-#include <asm/arch/platform.h>
-
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
-
-/*
- *************************************************************************
- *
- * Handy dandy macros
- *
- *************************************************************************
- */
-
-/* Delay a bit */
-.macro DELAY_FOR cycles, reg0
-	ldr     \reg0, =\cycles
-	subs    \reg0, \reg0, #1
-	subne   pc,  pc, #0xc
-.endm
-
-/*
- *************************************************************************
- *
- * Some local storage.
- *
- *************************************************************************
- */
-
-/* Should we boot with an interactive console or not */
-.globl serial_console
-
-/*
- *************************************************************************
- *
- * Raw hardware initialization code. The important thing is to get
- * SDRAM setup and running. We do some other basic things here too,
- * like getting the PLL set for high speed, and init the LEDs.
- *
- *************************************************************************
- */
-
-.globl lowlevel_init
-lowlevel_init:
-
-#if DEBUG
-	/*
-	 * enable UART for early debug trace
-	 */
-	ldr	r1, =(KS8695_IO_BASE+KS8695_UART_DIVISOR)
-	mov	r2, #((25000000+CONFIG_BAUDRATE/2) / CONFIG_BAUDRATE)
-	str	r2, [r1]
-	ldr	r1, =(KS8695_IO_BASE+KS8695_UART_LINE_CTRL)
-	mov	r2, #KS8695_UART_LINEC_WLEN8
-	str	r2, [r1]		/* 8 data bits, no parity, 1 stop */
-	ldr	r1, =(KS8695_IO_BASE+KS8695_UART_TX_HOLDING)
-	mov	r2, #0x41
-	str	r2, [r1]		/* write 'A' */
-#endif
-#if DEBUG
-	ldr	r1, =(KS8695_IO_BASE+KS8695_UART_TX_HOLDING)
-	mov	r2, #0x42
-	str	r2, [r1]
-#endif
-
-	/*
-	 * remap the memory and flash regions. we want to end up with
-	 * ram from address 0, and flash at 32MB.
-	 */
-	ldr	r1, =(KS8695_IO_BASE+KS8695_MEM_CTRL0)
-	ldr	r2, =0xbfc00040
-	str	r2, [r1]		/* large flash map */
-	ldr	pc, =(highflash+0x02000000-0x00f00000)	/* jump to high flash address */
-highflash:
-	ldr	r2, =0x8fe00040
-	str	r2, [r1]		/* remap flash range */
-
-	/*
-	 * remap the second select region to the 4MB immediately after
-	 * the first region. This way if you have a larger flash (say 8Mb)
-	 * then you can have it all mapped nicely. Has no effect if you
-	 * only have a 4Mb or smaller flash.
-	 */
-	ldr	r1, =(KS8695_IO_BASE+KS8695_MEM_CTRL1)
-	ldr	r2, =0x9fe40040
-	str	r2, [r1]		/* remap flash2 region, contiguous */
-	ldr	r1, =(KS8695_IO_BASE+KS8695_MEM_GENERAL)
-	ldr	r2, =0x30000005
-	str	r2, [r1]		/* enable both flash selects */
-
-#ifdef CONFIG_CM41xx
-	/*
-	 * map the second flash chip, using the external IO lines.
-	 */
-	ldr	r1, =(KS8695_IO_BASE+KS8695_IO_CTRL0)
-	ldr	r2, =0xafe80b6d
-	str	r2, [r1]		/* remap io0 region, contiguous */
-	ldr	r1, =(KS8695_IO_BASE+KS8695_IO_CTRL1)
-	ldr	r2, =0xbfec0b6d
-	str	r2, [r1]		/* remap io1 region, contiguous */
-	ldr	r1, =(KS8695_IO_BASE+KS8695_MEM_GENERAL)
-	ldr	r2, =0x30050005
-	str	r2, [r1]		/* enable second flash */
-#endif
-
-	/*
-	 * before relocating, we have to setup RAM timing
-	 */
-	ldr	r1, =(KS8695_IO_BASE+KS8695_SDRAM_CTRL0)
-#if (PHYS_SDRAM_1_SIZE == 0x02000000)
-	ldr	r2, =0x7fc0000e		/* 32MB */
-#else
-	ldr	r2, =0x3fc0000e		/* 16MB */
-#endif
-	str	r2, [r1]		/* configure sdram bank0 setup */
-	ldr	r1, =(KS8695_IO_BASE+KS8695_SDRAM_CTRL1)
-	mov	r2, #0
-	str	r2, [r1]		/* configure sdram bank1 setup */
-
-	ldr	r1, =(KS8695_IO_BASE+KS8695_SDRAM_GENERAL)
-	ldr	r2, =0x0000000a
-	str	r2, [r1]		/* set RAS/CAS timing */
-
-	ldr	r1, =(KS8695_IO_BASE+KS8695_SDRAM_BUFFER)
-	ldr	r2, =0x00030000
-	str	r2, [r1]		/* send NOP command */
-	DELAY_FOR 0x100, r0
-	ldr	r2, =0x00010000
-	str	r2, [r1]		/* send PRECHARGE-ALL */
-	DELAY_FOR 0x100, r0
-
-	ldr	r1, =(KS8695_IO_BASE+KS8695_SDRAM_REFRESH)
-	ldr	r2, =0x00000020
-	str	r2, [r1]		/* set for fast refresh */
-	DELAY_FOR 0x100, r0
-	ldr	r2, =0x00000190
-	str	r2, [r1]		/* set normal refresh timing */
-
-	ldr	r1, =(KS8695_IO_BASE+KS8695_SDRAM_BUFFER)
-	ldr	r2, =0x00020033
-	str	r2, [r1]		/* send mode command */
-	DELAY_FOR 0x100, r0
-	ldr	r2, =0x01f00000
-	str	r2, [r1]		/* enable sdram fifos */
-
-	/*
-	 * set pll to top speed
-	 */
-	ldr	r1, =(KS8695_IO_BASE+KS8695_SYSTEN_BUS_CLOCK)
-	mov	r2, #0
-	str	r2, [r1]		/* set pll clock to 166MHz */
-
-	ldr	r1, =(KS8695_IO_BASE+KS8695_SWITCH_CTRL0)
-	ldr	r2, [r1]		/* Get switch ctrl0 register       */
-	and	r2, r2, #0x0fc00000	/* Mask out LED control bits       */
-	orr	r2, r2, #0x01800000	/* Set Link/activity/speed actions */
-	str	r2, [r1]
-
-#ifdef CONFIG_CM4008
-	ldr	r1, =(KS8695_IO_BASE+KS8695_GPIO_MODE)
-	ldr	r2, =0x0000fe30
-	str	r2, [r1]		/* enable LED's as outputs	    */
-	ldr	r1, =(KS8695_IO_BASE+KS8695_GPIO_DATA)
-	ldr	r2, =0x0000fe20
-	str	r2, [r1]		/* turn on power LED		    */
-#endif
-#if defined(CONFIG_CM4008) || defined(CONFIG_CM41xx)
-	ldr	r2, [r1]		/* get current GPIO input data	    */
-	tst	r2, #0x8		/* check if "erase" depressed	    */
-	beq	nobutton
-	mov	r2, #0			/* be quiet on boot, no console	    */
-	ldr	r1, =serial_console
-	str	r2, [r1]
-nobutton:
-#endif
-
-	add	lr, lr, #0x02000000	/* flash is now mapped high */
-	add	ip, ip, #0x02000000	/* this is a hack */
-	mov	pc, lr			/* all done, return */
-
-#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
diff --git a/arch/arm/cpu/arm920t/ks8695/timer.c b/arch/arm/cpu/arm920t/ks8695/timer.c
deleted file mode 100644
index 23db5572de..0000000000
--- a/arch/arm/cpu/arm920t/ks8695/timer.c
+++ /dev/null
@@ -1,77 +0,0 @@
-/*
- * (C) Copyright 2004-2005, Greg Ungerer <greg.ungerer@opengear.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/arch/platform.h>
-
-/*
- * Initial timer set constants. Nothing complicated, just set for a 1ms
- * tick.
- */
-#define	TIMER_INTERVAL	(TICKS_PER_uSEC * mSEC_1)
-#define	TIMER_COUNT	(TIMER_INTERVAL / 2)
-#define	TIMER_PULSE	TIMER_COUNT
-
-/*
- * Handy KS8695 register access functions.
- */
-#define	ks8695_read(a)    *((volatile ulong *) (KS8695_IO_BASE + (a)))
-#define	ks8695_write(a,v) *((volatile ulong *) (KS8695_IO_BASE + (a))) = (v)
-
-ulong timer_ticks;
-
-int timer_init (void)
-{
-	/* Set the hadware timer for 1ms */
-	ks8695_write(KS8695_TIMER1, TIMER_COUNT);
-	ks8695_write(KS8695_TIMER1_PCOUNT, TIMER_PULSE);
-	ks8695_write(KS8695_TIMER_CTRL, 0x2);
-	timer_ticks = 0;
-
-	return 0;
-}
-
-ulong get_timer_masked(void)
-{
-	/* Check for timer wrap */
-	if (ks8695_read(KS8695_INT_STATUS) & KS8695_INTMASK_TIMERINT1) {
-		/* Clear interrupt condition */
-		ks8695_write(KS8695_INT_STATUS, KS8695_INTMASK_TIMERINT1);
-		timer_ticks++;
-	}
-	return timer_ticks;
-}
-
-ulong get_timer(ulong base)
-{
-       return (get_timer_masked() - base);
-}
-
-void __udelay(ulong usec)
-{
-	ulong start = get_timer_masked();
-	ulong end;
-
-	/* Only 1ms resolution :-( */
-	end = usec / 1000;
-	while (get_timer(start) < end)
-		;
-}
-
-void reset_cpu (ulong ignored)
-{
-	ulong tc;
-
-	/* Set timer0 to watchdog, and let it timeout */
-	tc = ks8695_read(KS8695_TIMER_CTRL) & 0x2;
-	ks8695_write(KS8695_TIMER_CTRL, tc);
-	ks8695_write(KS8695_TIMER0, ((10 << 8) | 0xff));
-	ks8695_write(KS8695_TIMER_CTRL, (tc | 0x1));
-
-	/* Should only wait here till watchdog resets */
-	for (;;)
-		;
-}