1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
|
Qualcomm APQ8064 TLMM block
Required properties:
- compatible: "qcom,apq8064-pinctrl"
- reg: Should be the base address and length of the TLMM block.
- interrupts: Should be the parent IRQ of the TLMM block.
- interrupt-controller: Marks the device node as an interrupt controller.
- #interrupt-cells: Should be two.
- gpio-controller: Marks the device node as a GPIO controller.
- #gpio-cells : Should be two.
The first cell is the gpio pin number and the
second cell is used for optional parameters.
- gpio-ranges: see ../gpio/gpio.txt
Optional properties:
- gpio-reserved-ranges: see ../gpio/gpio.txt
Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
a general description of GPIO and interrupt bindings.
Please refer to pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices, including the meaning of the
phrase "pin configuration node".
Qualcomm's pin configuration nodes act as a container for an arbitrary number of
subnodes. Each of these subnodes represents some desired configuration for a
pin, a group, or a list of pins or groups. This configuration can include the
mux function to select on those pin(s)/group(s), and various pin configuration
parameters, such as pull-up, drive strength, etc.
The name of each subnode is not important; all subnodes should be enumerated
and processed purely based on their content.
Each subnode only affects those parameters that are explicitly listed. In
other words, a subnode that lists a mux function but no pin configuration
parameters implies no information about any pin configuration parameters.
Similarly, a pin subnode that describes a pullup parameter implies no
information about e.g. the mux function.
The following generic properties as defined in pinctrl-bindings.txt are valid
to specify in a pin configuration subnode:
pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength,
output-low, output-high.
Non-empty subnodes must specify the 'pins' property.
Valid values for pins are:
gpio0-gpio89
Valid values for function are:
cam_mclk, codec_mic_i2s, codec_spkr_i2s, gp_clk_0a, gp_clk_0b, gp_clk_1a,
gp_clk_1b, gp_clk_2a, gp_clk_2b, gpio, gsbi1, gsbi2, gsbi3, gsbi4,
gsbi4_cam_i2c, gsbi5, gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6,
gsbi6_spi_cs1, gsbi6_spi_cs2, gsbi6_spi_cs3, gsbi7, gsbi7_spi_cs1,
gsbi7_spi_cs2, gsbi7_spi_cs3, gsbi_cam_i2c, hdmi, mi2s, riva_bt, riva_fm,
riva_wlan, sdc2, sdc4, slimbus, spkr_i2s, tsif1, tsif2, usb2_hsic, ps_hold
Example:
msmgpio: pinctrl@800000 {
compatible = "qcom,apq8064-pinctrl";
reg = <0x800000 0x4000>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
interrupts = <0 16 0x4>;
pinctrl-names = "default";
pinctrl-0 = <&gsbi5_uart_default>;
gpio-ranges = <&msmgpio 0 0 90>;
gsbi5_uart_default: gsbi5_uart_default {
mux {
pins = "gpio51", "gpio52";
function = "gsbi5";
};
tx {
pins = "gpio51";
drive-strength = <4>;
bias-disable;
};
rx {
pins = "gpio52";
drive-strength = <2>;
bias-pull-up;
};
};
};
|
