| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: "Antti Seppälä" <a.seppala@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since commit 12749b198fa4 ("[media] rc: saa7134: add trailing space for
timely decoding"), the workaround of inserting reset events is no
longer needed.
Note that the initial reset is not needed either; other rc-core drivers
that don't use ir_raw_event_store_edge() never call this at all.
Verified on a HVR-1150 and Raspberry Pi.
Fixes: 3f5c4c73322e ("[media] rc: fix ghost keypresses with certain hw")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When an ir-spi is registered, you get this message.
rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
"Unspecified device" refers to input_name, which makes no sense for IR
TX only devices. So, rename to device_name.
Also make driver_name const char* so that no casts are needed anywhere.
Now ir-spi reports:
rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The driver type can be assigned immediately when an RC device
requests to the framework to allocate the device.
This is an 'enum rc_driver_type' data type and specifies whether
the device is a raw receiver or scancode receiver. The type will
be given as parameter to the rc_allocate_device device.
Change accordingly all the drivers calling rc_allocate_device()
so that the device type is specified during the rc device
allocation. Whenever the device type is not specified, it will be
set as RC_DRIVER_SCANCODE which was the default '0' value.
Suggested-by: Sean Young <sean@mess.org>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
| |
|
|
|
|
|
|
|
| |
Add the basic GPLv2+ license notice to the copyright headers at the top
of all the source files in the img-ir driver.
Reported-by: David Härdeman <david@hardeman.nu>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
|
Add raw IR remote control input driver for the ImgTec Infrared decoder
block's raw edge interrupts. Generic software protocol decoders are used
to allow multiple protocols to be supported at a time, including those
not supported by the hardware decoder.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
