2 files changed, 111 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/sound/brcm,cygnus-audio.txt b/Documentation/devicetree/bindings/sound/brcm,cygnus-audio.txt
new file mode 100644
index 000000000000..b139e66d2a11
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/brcm,cygnus-audio.txt
@@ -0,0 +1,67 @@
+BROADCOM Cygnus Audio I2S/TDM/SPDIF controller
+
+Required properties:
+	- compatible : "brcm,cygnus-audio"
+	- #address-cells: 32bit valued, 1 cell.
+	- #size-cells:  32bit valued, 0 cell.
+	- reg : Should contain audio registers location and length
+	- reg-names: names of the registers listed in "reg" property
+		Valid names are "aud" and "i2s_in". "aud" contains a
+		set of DMA, I2S_OUT and SPDIF registers. "i2s_in" contains
+		a set of I2S_IN registers.
+	- clocks: PLL and leaf clocks used by audio ports
+	- assigned-clocks: PLL and leaf clocks
+	- assigned-clock-parents: parent clocks of the assigned clocks
+		(usually the PLL)
+	- assigned-clock-rates: List of clock frequencies of the
+		assigned clocks
+	- clock-names: names of 3 leaf clocks used by audio ports
+		Valid names are "ch0_audio", "ch1_audio", "ch2_audio"
+	- interrupts: audio DMA interrupt number
+
+SSP Subnode properties:
+- reg: The index of ssp port interface to use
+	Valid value are 0, 1, 2, or 3 (for spdif)
+
+Example:
+	cygnus_audio: audio@180ae000 {
+		compatible = "brcm,cygnus-audio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x180ae000 0xafd>, <0x180aec00 0x1f8>;
+		reg-names = "aud", "i2s_in";
+		clocks = <&audiopll BCM_CYGNUS_AUDIOPLL_CH0>,
+				<&audiopll BCM_CYGNUS_AUDIOPLL_CH1>,
+				<&audiopll BCM_CYGNUS_AUDIOPLL_CH2>;
+		assigned-clocks = <&audiopll BCM_CYGNUS_AUDIOPLL>,
+							<&audiopll BCM_CYGNUS_AUDIOPLL_CH0>,
+							<&audiopll BCM_CYGNUS_AUDIOPLL_CH1>,
+							<&audiopll BCM_CYGNUS_AUDIOPLL_CH2>;
+		assigned-clock-parents = <&audiopll BCM_CYGNUS_AUDIOPLL>;
+		assigned-clock-rates = <1769470191>,
+								<0>,
+								<0>,
+								<0>;
+		clock-names = "ch0_audio", "ch1_audio", "ch2_audio";
+		interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+
+		ssp0: ssp_port@0 {
+			reg = <0>;
+			status = "okay";
+		};
+
+		ssp1: ssp_port@1 {
+			reg = <1>;
+			status = "disabled";
+		};
+
+		ssp2: ssp_port@2 {
+			reg = <2>;
+			status = "disabled";
+		};
+
+		spdif: spdif_port@3 {
+			reg = <3>;
+			status = "disabled";
+		};
+	};
diff --git a/Documentation/devicetree/bindings/sound/cs53l30.txt b/Documentation/devicetree/bindings/sound/cs53l30.txt
new file mode 100644
index 000000000000..4dbfb8274cd9
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/cs53l30.txt
@@ -0,0 +1,44 @@
+CS53L30 audio CODEC
+
+Required properties:
+
+  - compatible : "cirrus,cs53l30"
+
+  - reg : the I2C address of the device
+
+  - VA-supply, VP-supply : power supplies for the device,
+    as covered in Documentation/devicetree/bindings/regulator/regulator.txt.
+
+Optional properties:
+
+  - reset-gpios : a GPIO spec for the reset pin.
+
+  - mute-gpios : a GPIO spec for the MUTE pin. The active state can be either
+		 GPIO_ACTIVE_HIGH or GPIO_ACTIVE_LOW, which would be handled
+		 by the driver automatically.
+
+  - cirrus,micbias-lvl : Set the output voltage level on the MICBIAS Pin.
+			 0 = Hi-Z
+			 1 = 1.80 V
+			 2 = 2.75 V
+
+  - cirrus,use-sdout2 : This is a boolean property. If present, it indicates
+			the hardware design connects both SDOUT1 and SDOUT2
+			pins to output data. Otherwise, it indicates that
+			only SDOUT1 is connected for data output.
+			* CS53l30 supports 4-channel data output in the same
+			* frame using two different ways:
+			* 1) Normal I2S mode on two data pins -- each SDOUT
+			*    carries 2-channel data in the same time.
+			* 2) TDM mode on one signle data pin -- SDOUT1 carries
+			*    4-channel data per frame.
+
+Example:
+
+codec: cs53l30@48 {
+	compatible = "cirrus,cs53l30";
+	reg = <0x48>;
+	reset-gpios = <&gpio 54 0>;
+	VA-supply = <&cs53l30_va>;
+	VP-supply = <&cs53l30_vp>;
+};