diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
44 files changed, 2560 insertions, 128 deletions
diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt index cbef09b5c8a7..69ddf9fad2dc 100644 --- a/Documentation/devicetree/bindings/arm/l2cc.txt +++ b/Documentation/devicetree/bindings/arm/l2cc.txt @@ -16,6 +16,9 @@ Required properties: performs the same operation). "marvell,"aurora-outer-cache: Marvell Controller designed to be compatible with the ARM one with outer cache mode. + "bcm,bcm11351-a2-pl310-cache": For Broadcom bcm11351 chipset where an + offset needs to be added to the address before passing down to the L2 + cache controller - cache-unified : Specifies the cache is a unified cache. - cache-level : Should be set to 2 for a level 2 cache. - reg : Physical base address and size of cache controller's memory mapped diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index b519f9b699c3..3ec0c5c4f0e9 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -12,6 +12,11 @@ Optional properties: - calxeda,port-phys: phandle-combophy and lane assignment, which maps each SATA port to a combophy and a lane within that combophy +- calxeda,sgpio-gpio: phandle-gpio bank, bit offset, and default on or off, + which indicates that the driver supports SGPIO + indicator lights using the indicated GPIOs +- calxeda,led-order : a u32 array that map port numbers to offsets within the + SGPIO bitstream. - dma-coherent : Present if dma operations are coherent Example: diff --git a/Documentation/devicetree/bindings/clock/nspire-clock.txt b/Documentation/devicetree/bindings/clock/nspire-clock.txt new file mode 100644 index 000000000000..7c3bc8bb5b9f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nspire-clock.txt @@ -0,0 +1,24 @@ +TI-NSPIRE Clocks + +Required properties: +- compatible: Valid compatible properties include: + "lsi,nspire-cx-ahb-divider" for the AHB divider in the CX model + "lsi,nspire-classic-ahb-divider" for the AHB divider in the older model + "lsi,nspire-cx-clock" for the base clock in the CX model + "lsi,nspire-classic-clock" for the base clock in the older model + +- reg: Physical base address of the controller and length of memory mapped + region. + +Optional: +- clocks: For the "nspire-*-ahb-divider" compatible clocks, this is the parent + clock where it divides the rate from. + +Example: + +ahb_clk { + #clock-cells = <0>; + compatible = "lsi,nspire-cx-clock"; + reg = <0x900B0000 0x4>; + clocks = <&base_clk>; +}; diff --git a/Documentation/devicetree/bindings/clock/rockchip.txt b/Documentation/devicetree/bindings/clock/rockchip.txt new file mode 100644 index 000000000000..a891c823ed44 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip.txt @@ -0,0 +1,74 @@ +Device Tree Clock bindings for arch-rockchip + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +== Gate clocks == + +The gate registers form a continuos block which makes the dt node +structure a matter of taste, as either all gates can be put into +one gate clock spanning all registers or they can be divided into +the 10 individual gates containing 16 clocks each. +The code supports both approaches. + +Required properties: +- compatible : "rockchip,rk2928-gate-clk" +- reg : shall be the control register address(es) for the clock. +- #clock-cells : from common clock binding; shall be set to 1 +- clock-output-names : the corresponding gate names that the clock controls +- clocks : should contain the parent clock for each individual gate, + therefore the number of clocks elements should match the number of + clock-output-names + +Example using multiple gate clocks: + + clk_gates0: gate-clk@200000d0 { + compatible = "rockchip,rk2928-gate-clk"; + reg = <0x200000d0 0x4>; + clocks = <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>; + + clock-output-names = + "gate_core_periph", "gate_cpu_gpll", + "gate_ddrphy", "gate_aclk_cpu", + "gate_hclk_cpu", "gate_pclk_cpu", + "gate_atclk_cpu", "gate_i2s0", + "gate_i2s0_frac", "gate_i2s1", + "gate_i2s1_frac", "gate_i2s2", + "gate_i2s2_frac", "gate_spdif", + "gate_spdif_frac", "gate_testclk"; + + #clock-cells = <1>; + }; + + clk_gates1: gate-clk@200000d4 { + compatible = "rockchip,rk2928-gate-clk"; + reg = <0x200000d4 0x4>; + clocks = <&xin24m>, <&xin24m>, + <&xin24m>, <&dummy>, + <&dummy>, <&xin24m>, + <&xin24m>, <&dummy>, + <&xin24m>, <&dummy>, + <&xin24m>, <&dummy>, + <&xin24m>, <&dummy>, + <&xin24m>, <&dummy>; + + clock-output-names = + "gate_timer0", "gate_timer1", + "gate_timer2", "gate_jtag", + "gate_aclk_lcdc1_src", "gate_otgphy0", + "gate_otgphy1", "gate_ddr_gpll", + "gate_uart0", "gate_frac_uart0", + "gate_uart1", "gate_frac_uart1", + "gate_uart2", "gate_frac_uart2", + "gate_uart3", "gate_frac_uart3"; + + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/silabs,si5351.txt b/Documentation/devicetree/bindings/clock/silabs,si5351.txt index cc374651662c..66c75b2d6158 100644 --- a/Documentation/devicetree/bindings/clock/silabs,si5351.txt +++ b/Documentation/devicetree/bindings/clock/silabs,si5351.txt @@ -44,6 +44,11 @@ Optional child node properties: - silabs,multisynth-source: source pll A(0) or B(1) of corresponding multisynth divider. - silabs,pll-master: boolean, multisynth can change pll frequency. +- silabs,disable-state : clock output disable state, shall be + 0 = clock output is driven LOW when disabled + 1 = clock output is driven HIGH when disabled + 2 = clock output is FLOATING (HIGH-Z) when disabled + 3 = clock output is NEVER disabled ==Example== diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt index 729f52426fe1..d495521a79d2 100644 --- a/Documentation/devicetree/bindings/clock/sunxi.txt +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -12,22 +12,30 @@ Required properties: "allwinner,sun4i-axi-clk" - for the AXI clock "allwinner,sun4i-axi-gates-clk" - for the AXI gates "allwinner,sun4i-ahb-clk" - for the AHB clock - "allwinner,sun4i-ahb-gates-clk" - for the AHB gates + "allwinner,sun4i-ahb-gates-clk" - for the AHB gates on A10 + "allwinner,sun5i-a13-ahb-gates-clk" - for the AHB gates on A13 "allwinner,sun4i-apb0-clk" - for the APB0 clock - "allwinner,sun4i-apb0-gates-clk" - for the APB0 gates + "allwinner,sun4i-apb0-gates-clk" - for the APB0 gates on A10 + "allwinner,sun5i-a13-apb0-gates-clk" - for the APB0 gates on A13 "allwinner,sun4i-apb1-clk" - for the APB1 clock "allwinner,sun4i-apb1-mux-clk" - for the APB1 clock muxing - "allwinner,sun4i-apb1-gates-clk" - for the APB1 gates + "allwinner,sun4i-apb1-gates-clk" - for the APB1 gates on A10 + "allwinner,sun5i-a13-apb1-gates-clk" - for the APB1 gates on A13 Required properties for all clocks: - reg : shall be the control register address for the clock. - clocks : shall be the input parent clock(s) phandle for the clock - #clock-cells : from common clock binding; shall be set to 0 except for - "allwinner,sun4i-*-gates-clk" where it shall be set to 1 + "allwinner,*-gates-clk" where it shall be set to 1 -Additionally, "allwinner,sun4i-*-gates-clk" clocks require: +Additionally, "allwinner,*-gates-clk" clocks require: - clock-output-names : the corresponding gate names that the clock controls +Clock consumers should specify the desired clocks they use with a +"clocks" phandle cell. Consumers that are using a gated clock should +provide an additional ID in their clock property. The values of this +ID are documented in sunxi/<soc>-gates.txt. + For example: osc24M: osc24M@01c20050 { @@ -50,102 +58,3 @@ cpu: cpu@01c20054 { reg = <0x01c20054 0x4>; clocks = <&osc32k>, <&osc24M>, <&pll1>; }; - - - -Gate clock outputs - -The "allwinner,sun4i-*-gates-clk" clocks provide several gatable outputs; -their corresponding offsets as present on sun4i are listed below. Note that -some of these gates are not present on sun5i. - - * AXI gates ("allwinner,sun4i-axi-gates-clk") - - DRAM 0 - - * AHB gates ("allwinner,sun4i-ahb-gates-clk") - - USB0 0 - EHCI0 1 - OHCI0 2* - EHCI1 3 - OHCI1 4* - SS 5 - DMA 6 - BIST 7 - MMC0 8 - MMC1 9 - MMC2 10 - MMC3 11 - MS 12** - NAND 13 - SDRAM 14 - - ACE 16 - EMAC 17 - TS 18 - - SPI0 20 - SPI1 21 - SPI2 22 - SPI3 23 - PATA 24 - SATA 25** - GPS 26* - - VE 32 - TVD 33 - TVE0 34 - TVE1 35 - LCD0 36 - LCD1 37 - - CSI0 40 - CSI1 41 - - HDMI 43 - DE_BE0 44 - DE_BE1 45 - DE_FE0 46 - DE_FE1 47 - - MP 50 - - MALI400 52 - - * APB0 gates ("allwinner,sun4i-apb0-gates-clk") - - CODEC 0 - SPDIF 1* - AC97 2 - IIS 3 - - PIO 5 - IR0 6 - IR1 7 - - KEYPAD 10 - - * APB1 gates ("allwinner,sun4i-apb1-gates-clk") - - I2C0 0 - I2C1 1 - I2C2 2 - - CAN 4 - SCR 5 - PS20 6 - PS21 7 - - UART0 16 - UART1 17 - UART2 18 - UART3 19 - UART4 20 - UART5 21 - UART6 22 - UART7 23 - -Notation: - [*]: The datasheet didn't mention these, but they are present on AW code - [**]: The datasheet had this marked as "NC" but they are used on AW code diff --git a/Documentation/devicetree/bindings/clock/sunxi/sun4i-a10-gates.txt b/Documentation/devicetree/bindings/clock/sunxi/sun4i-a10-gates.txt new file mode 100644 index 000000000000..6a03475bbfe2 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sunxi/sun4i-a10-gates.txt @@ -0,0 +1,93 @@ +Gate clock outputs +------------------ + + * AXI gates ("allwinner,sun4i-axi-gates-clk") + + DRAM 0 + + * AHB gates ("allwinner,sun4i-ahb-gates-clk") + + USB0 0 + EHCI0 1 + OHCI0 2* + EHCI1 3 + OHCI1 4* + SS 5 + DMA 6 + BIST 7 + MMC0 8 + MMC1 9 + MMC2 10 + MMC3 11 + MS 12** + NAND 13 + SDRAM 14 + + ACE 16 + EMAC 17 + TS 18 + + SPI0 20 + SPI1 21 + SPI2 22 + SPI3 23 + PATA 24 + SATA 25** + GPS 26* + + VE 32 + TVD 33 + TVE0 34 + TVE1 35 + LCD0 36 + LCD1 37 + + CSI0 40 + CSI1 41 + + HDMI 43 + DE_BE0 44 + DE_BE1 45 + DE_FE1 46 + DE_FE1 47 + + MP 50 + + MALI400 52 + + * APB0 gates ("allwinner,sun4i-apb0-gates-clk") + + CODEC 0 + SPDIF 1* + AC97 2 + IIS 3 + + PIO 5 + IR0 6 + IR1 7 + + KEYPAD 10 + + * APB1 gates ("allwinner,sun4i-apb1-gates-clk") + + I2C0 0 + I2C1 1 + I2C2 2 + + CAN 4 + SCR 5 + PS20 6 + PS21 7 + + UART0 16 + UART1 17 + UART2 18 + UART3 19 + UART4 20 + UART5 21 + UART6 22 + UART7 23 + +Notation: + [*]: The datasheet didn't mention these, but they are present on AW code + [**]: The datasheet had this marked as "NC" but they are used on AW code diff --git a/Documentation/devicetree/bindings/clock/sunxi/sun5i-a13-gates.txt b/Documentation/devicetree/bindings/clock/sunxi/sun5i-a13-gates.txt new file mode 100644 index 000000000000..006b6dfc4703 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sunxi/sun5i-a13-gates.txt @@ -0,0 +1,58 @@ +Gate clock outputs +------------------ + + * AXI gates ("allwinner,sun4i-axi-gates-clk") + + DRAM 0 + + * AHB gates ("allwinner,sun5i-a13-ahb-gates-clk") + + USBOTG 0 + EHCI 1 + OHCI 2 + + SS 5 + DMA 6 + BIST 7 + MMC0 8 + MMC1 9 + MMC2 10 + + NAND 13 + SDRAM 14 + + SPI0 20 + SPI1 21 + SPI2 22 + + STIMER 28 + + VE 32 + + LCD 36 + + CSI 40 + + DE_BE 44 + + DE_FE 46 + + IEP 51 + MALI400 52 + + * APB0 gates ("allwinner,sun5i-a13-apb0-gates-clk") + + CODEC 0 + + PIO 5 + IR 6 + + * APB1 gates ("allwinner,sun5i-a13-apb1-gates-clk") + + I2C0 0 + I2C1 1 + I2C2 2 + + UART1 17 + + UART3 19 diff --git a/Documentation/devicetree/bindings/clock/vt8500.txt b/Documentation/devicetree/bindings/clock/vt8500.txt index a880c70d0047..91d71cc0314a 100644 --- a/Documentation/devicetree/bindings/clock/vt8500.txt +++ b/Documentation/devicetree/bindings/clock/vt8500.txt @@ -8,6 +8,8 @@ Required properties: - compatible : shall be one of the following: "via,vt8500-pll-clock" - for a VT8500/WM8505 PLL clock "wm,wm8650-pll-clock" - for a WM8650 PLL clock + "wm,wm8750-pll-clock" - for a WM8750 PLL clock + "wm,wm8850-pll-clock" - for a WM8850 PLL clock "via,vt8500-device-clock" - for a VT/WM device clock Required properties for PLL clocks: diff --git a/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt b/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt new file mode 100644 index 000000000000..63bf4becd5f0 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt @@ -0,0 +1,48 @@ +Xilinx plb/axi GPIO controller + +Dual channel GPIO controller with configurable number of pins +(from 1 to 32 per channel). Every pin can be configured as +input/output/tristate. Both channels share the same global IRQ but +local interrupts can be enabled on channel basis. + +Required properties: +- compatible : Should be "xlnx,xps-gpio-1.00.a" +- reg : Address and length of the register set for the device +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). +- gpio-controller : Marks the device node as a GPIO controller. + +Optional properties: +- interrupts : Interrupt mapping for GPIO IRQ. +- interrupt-parent : Phandle for the interrupt controller that + services interrupts for this device. +- xlnx,all-inputs : if n-th bit is setup, GPIO-n is input +- xlnx,dout-default : if n-th bit is 1, GPIO-n default value is 1 +- xlnx,gpio-width : gpio width +- xlnx,tri-default : if n-th bit is 1, GPIO-n is in tristate mode +- xlnx,is-dual : if 1, controller also uses the second channel +- xlnx,all-inputs-2 : as above but for the second channel +- xlnx,dout-default-2 : as above but the second channel +- xlnx,gpio2-width : as above but for the second channel +- xlnx,tri-default-2 : as above but for the second channel + + +Example: +gpio: gpio@40000000 { + #gpio-cells = <2>; + compatible = "xlnx,xps-gpio-1.00.a"; + gpio-controller ; + interrupt-parent = <µblaze_0_intc>; + interrupts = < 6 2 >; + reg = < 0x40000000 0x10000 >; + xlnx,all-inputs = <0x0>; + xlnx,all-inputs-2 = <0x0>; + xlnx,dout-default = <0x0>; + xlnx,dout-default-2 = <0x0>; + xlnx,gpio-width = <0x2>; + xlnx,gpio2-width = <0x2>; + xlnx,interrupt-present = <0x1>; + xlnx,is-dual = <0x1>; + xlnx,tri-default = <0xffffffff>; + xlnx,tri-default-2 = <0xffffffff>; +} ; diff --git a/Documentation/devicetree/bindings/hwmon/g762.txt b/Documentation/devicetree/bindings/hwmon/g762.txt new file mode 100644 index 000000000000..25cc6d8ee575 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/g762.txt @@ -0,0 +1,47 @@ +GMT G762/G763 PWM Fan controller + +Required node properties: + + - "compatible": must be either "gmt,g762" or "gmt,g763" + - "reg": I2C bus address of the device + - "clocks": a fixed clock providing input clock frequency + on CLK pin of the chip. + +Optional properties: + + - "fan_startv": fan startup voltage. Accepted values are 0, 1, 2 and 3. + The higher the more. + + - "pwm_polarity": pwm polarity. Accepted values are 0 (positive duty) + and 1 (negative duty). + + - "fan_gear_mode": fan gear mode. Supported values are 0, 1 and 2. + +If an optional property is not set in .dts file, then current value is kept +unmodified (e.g. u-boot installed value). + +Additional information on operational parameters for the device is available +in Documentation/hwmon/g762. A detailed datasheet for the device is available +at http://natisbad.org/NAS/refs/GMT_EDS-762_763-080710-0.2.pdf. + +Example g762 node: + + clocks { + #address-cells = <1>; + #size-cells = <0>; + + g762_clk: fixedclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <8192>; + } + } + + g762: g762@3e { + compatible = "gmt,g762"; + reg = <0x3e>; + clocks = <&g762_clk> + fan_gear_mode = <0>; /* chip default */ + fan_startv = <1>; /* chip default */ + pwm_polarity = <0>; /* chip default */ + }; diff --git a/Documentation/devicetree/bindings/i2c/ina2xx.txt b/Documentation/devicetree/bindings/i2c/ina2xx.txt new file mode 100644 index 000000000000..a2ad85d7e747 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/ina2xx.txt @@ -0,0 +1,22 @@ +ina2xx properties + +Required properties: +- compatible: Must be one of the following: + - "ti,ina219" for ina219 + - "ti,ina220" for ina220 + - "ti,ina226" for ina226 + - "ti,ina230" for ina230 +- reg: I2C address + +Optional properties: + +- shunt-resistor + Shunt resistor value in micro-Ohm + +Example: + +ina220@44 { + compatible = "ti,ina220"; + reg = <0x44>; + shunt-resistor = <1000>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/abilis,tb10x-ictl.txt b/Documentation/devicetree/bindings/interrupt-controller/abilis,tb10x-ictl.txt new file mode 100644 index 000000000000..9d52d5afe3e9 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/abilis,tb10x-ictl.txt @@ -0,0 +1,38 @@ +TB10x Top Level Interrupt Controller +==================================== + +The Abilis TB10x SOC contains a custom interrupt controller. It performs +one-to-one mapping of external interrupt sources to CPU interrupts and +provides support for reconfigurable trigger modes. + +Required properties +------------------- + +- compatible: Should be "abilis,tb10x-ictl" +- reg: specifies physical base address and size of register range. +- interrupt-congroller: Identifies the node as an interrupt controller. +- #interrupt cells: Specifies the number of cells used to encode an interrupt + source connected to this controller. The value shall be 2. +- interrupt-parent: Specifies the parent interrupt controller. +- interrupts: Specifies the list of interrupt lines which are handled by + the interrupt controller in the parent controller's notation. Interrupts + are mapped one-to-one to parent interrupts. + +Example +------- + +intc: interrupt-controller { /* Parent interrupt controller */ + interrupt-controller; + #interrupt-cells = <1>; /* For example below */ + /* ... */ +}; + +tb10x_ictl: pic@2000 { /* TB10x interrupt controller */ + compatible = "abilis,tb10x-ictl"; + reg = <0x2000 0x20>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&intc>; + interrupts = <5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 30 31>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,orion-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,orion-intc.txt new file mode 100644 index 000000000000..2c11ac76fac9 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,orion-intc.txt @@ -0,0 +1,48 @@ +Marvell Orion SoC interrupt controllers + +* Main interrupt controller + +Required properties: +- compatible: shall be "marvell,orion-intc" +- reg: base address(es) of interrupt registers starting with CAUSE register +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: number of cells to encode an interrupt source, shall be 1 + +The interrupt sources map to the corresponding bits in the interrupt +registers, i.e. +- 0 maps to bit 0 of first base address, +- 1 maps to bit 1 of first base address, +- 32 maps to bit 0 of second base address, and so on. + +Example: + intc: interrupt-controller { + compatible = "marvell,orion-intc"; + interrupt-controller; + #interrupt-cells = <1>; + /* Dove has 64 first level interrupts */ + reg = <0x20200 0x10>, <0x20210 0x10>; + }; + +* Bridge interrupt controller + +Required properties: +- compatible: shall be "marvell,orion-bridge-intc" +- reg: base address of bridge interrupt registers starting with CAUSE register +- interrupts: bridge interrupt of the main interrupt controller +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: number of cells to encode an interrupt source, shall be 1 + +Optional properties: +- marvell,#interrupts: number of interrupts provided by bridge interrupt + controller, defaults to 32 if not set + +Example: + bridge_intc: interrupt-controller { + compatible = "marvell,orion-bridge-intc"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x20110 0x8>; + interrupts = <0>; + /* Dove bridge provides 5 interrupts */ + marvell,#interrupts = <5>; + }; diff --git a/Documentation/devicetree/bindings/leds/leds-lp55xx.txt b/Documentation/devicetree/bindings/leds/leds-lp55xx.txt new file mode 100644 index 000000000000..d5176882d8b9 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-lp55xx.txt @@ -0,0 +1,147 @@ +Binding for TI/National Semiconductor LP55xx Led Drivers + +Required properties: +- compatible: "national,lp5521" or "national,lp5523" or "ti,lp5562" +- reg: I2C slave address +- clock-mode: Input clock mode, (0: automode, 1: internal, 2: external) + +Each child has own specific current settings +- led-cur: Current setting at each led channel (mA x10, 0 if led is not connected) +- max-cur: Maximun current at each led channel. + +Optional properties: +- label: Used for naming LEDs + +Alternatively, each child can have specific channel name +- chan-name: Name of each channel name + +example 1) LP5521 +3 LED channels, external clock used. Channel names are 'lp5521_pri:channel0', +'lp5521_pri:channel1' and 'lp5521_pri:channel2' + +lp5521@32 { + compatible = "national,lp5521"; + reg = <0x32>; + label = "lp5521_pri"; + clock-mode = /bits/ 8 <2>; + + chan0 { + led-cur = /bits/ 8 <0x2f>; + max-cur = /bits/ 8 <0x5f>; + }; + + chan1 { + led-cur = /bits/ 8 <0x2f>; + max-cur = /bits/ 8 <0x5f>; + }; + + chan2 { + led-cur = /bits/ 8 <0x2f>; + max-cur = /bits/ 8 <0x5f>; + }; +}; + +example 2) LP5523 +9 LED channels with specific name. Internal clock used. +The I2C slave address is configurable with ASEL1 and ASEL0 pins. +Available addresses are 32/33/34/35h. + +ASEL1 ASEL0 Address +------------------------- + GND GND 32h + GND VEN 33h + VEN GND 34h + VEN VEN 35h + +lp5523@32 { + compatible = "national,lp5523"; + reg = <0x32>; + clock-mode = /bits/ 8 <1>; + + chan0 { + chan-name = "d1"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan1 { + chan-name = "d2"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan2 { + chan-name = "d3"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan3 { + chan-name = "d4"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan4 { + chan-name = "d5"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan5 { + chan-name = "d6"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan6 { + chan-name = "d7"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan7 { + chan-name = "d8"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan8 { + chan-name = "d9"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; +}; + +example 3) LP5562 +4 channels are defined. + +lp5562@30 { + compatible = "ti,lp5562"; + reg = <0x30>; + clock-mode = /bits/8 <2>; + + chan0 { + chan-name = "R"; + led-cur = /bits/ 8 <0x20>; + max-cur = /bits/ 8 <0x60>; + }; + + chan1 { + chan-name = "G"; + led-cur = /bits/ 8 <0x20>; + max-cur = /bits/ 8 <0x60>; + }; + + chan2 { + chan-name = "B"; + led-cur = /bits/ 8 <0x20>; + max-cur = /bits/ 8 <0x60>; + }; + + chan3 { + chan-name = "W"; + led-cur = /bits/ 8 <0x20>; + max-cur = /bits/ 8 <0x60>; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt new file mode 100644 index 000000000000..0e295c9d8937 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/arizona.txt @@ -0,0 +1,62 @@ +Wolfson Arizona class audio SoCs + +These devices are audio SoCs with extensive digital capabilites and a range +of analogue I/O. + +Required properties: + + - compatible : one of the following chip-specific strings: + "wlf,wm5102" + "wlf,wm5110" + - reg : I2C slave address when connected using I2C, chip select number when + using SPI. + + - interrupts : The interrupt line the /IRQ signal for the device is + connected to. + - interrupt-controller : Arizona class devices contain interrupt controllers + and may provide interrupt services to other devices. + - interrupt-parent : The parent interrupt controller. + - #interrupt-cells: the number of cells to describe an IRQ, this should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as the trigger masks from + Documentation/devicetree/bindings/interrupts.txt + + - gpio-controller : Indicates this device is a GPIO controller. + - #gpio-cells : Must be 2. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + + - AVDD1-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, CPVDD-supply, + SPKVDDL-supply, SPKVDDR-supply : power supplies for the device, as covered + in Documentation/devicetree/bindings/regulator/regulator.txt + +Optional properties: + + - wlf,reset : GPIO specifier for the GPIO controlling /RESET + - wlf,ldoena : GPIO specifier for the GPIO controlling LDOENA + + - wlf,gpio-defaults : A list of GPIO configuration register values. If + absent, no configuration of these registers is performed. If any + entry has a value that is out of range for a 16 bit register then + the chip default will be used. If present exactly five values must + be specified. + +Example: + +codec: wm5102@1a { + compatible = "wlf,wm5102"; + reg = <0x1a>; + interrupts = <347>; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + + gpio-controller; + #gpio-cells = <2>; + + wlf,gpio-defaults = < + 0x00000000, /* AIF1TXLRCLK */ + 0xffffffff, + 0xffffffff, + 0xffffffff, + 0xffffffff, + >; +}; diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt new file mode 100644 index 000000000000..11921cc417bf --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77693.txt @@ -0,0 +1,55 @@ +Maxim MAX77693 multi-function device + +MAX77693 is a Multifunction device with the following submodules: +- PMIC, +- CHARGER, +- LED, +- MUIC, +- HAPTIC + +It is interfaced to host controller using i2c. +This document describes the bindings for the mfd device. + +Required properties: +- compatible : Must be "maxim,max77693". +- reg : Specifies the i2c slave address of PMIC block. +- interrupts : This i2c device has an IRQ line connected to the main SoC. +- interrupt-parent : The parent interrupt controller. + +Optional properties: +- regulators : The regulators of max77693 have to be instantiated under subnod + named "regulators" using the following format. + + regulators { + regualtor-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER + standard regulator constratints[*]. + }; + + [*] refer Documentation/devicetree/bindings/regulator/regulator.txt + +Example: + max77693@66 { + compatible = "maxim,max77693"; + reg = <0x66>; + interrupt-parent = <&gpx1>; + interrupts = <5 2>; + + regulators { + esafeout@1 { + regulator-compatible = "ESAFEOUT1"; + regulator-name = "ESAFEOUT1"; + regulator-boot-on; + }; + esafeout@2 { + regulator-compatible = "ESAFEOUT2"; + regulator-name = "ESAFEOUT2"; + }; + charger@0 { + regulator-compatible = "CHARGER"; + regulator-name = "CHARGER"; + regulator-min-microamp = <60000>; + regulator-max-microamp = <2580000>; + regulator-boot-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,vf610-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,vf610-pinctrl.txt new file mode 100644 index 000000000000..ddcdeb697c29 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,vf610-pinctrl.txt @@ -0,0 +1,41 @@ +Freescale Vybrid VF610 IOMUX Controller + +Please refer to fsl,imx-pinctrl.txt in this directory for common binding part +and usage. + +Required properties: +- compatible: "fsl,vf610-iomuxc" +- fsl,pins: two integers array, represents a group of pins mux and config + setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is + a pin working on a specific function, CONFIG is the pad setting value + such as pull-up, speed, ode for this pin. Please refer to Vybrid VF610 + datasheet for the valid pad config settings. + +CONFIG bits definition: +PAD_CTL_SPEED_LOW (1 << 12) +PAD_CTL_SPEED_MED (2 << 12) +PAD_CTL_SPEED_HIGH (3 << 12) +PAD_CTL_SRE_FAST (1 << 11) +PAD_CTL_SRE_SLOW (0 << 11) +PAD_CTL_ODE (1 << 10) +PAD_CTL_HYS (1 << 9) +PAD_CTL_DSE_DISABLE (0 << 6) +PAD_CTL_DSE_150ohm (1 << 6) +PAD_CTL_DSE_75ohm (2 << 6) +PAD_CTL_DSE_50ohm (3 << 6) +PAD_CTL_DSE_37ohm (4 << 6) +PAD_CTL_DSE_30ohm (5 << 6) +PAD_CTL_DSE_25ohm (6 << 6) +PAD_CTL_DSE_20ohm (7 << 6) +PAD_CTL_PUS_100K_DOWN (0 << 4) +PAD_CTL_PUS_47K_UP (1 << 4) +PAD_CTL_PUS_100K_UP (2 << 4) +PAD_CTL_PUS_22K_UP (3 << 4) +PAD_CTL_PKE (1 << 3) +PAD_CTL_PUE (1 << 2) +PAD_CTL_OBE_ENABLE (1 << 1) +PAD_CTL_IBE_ENABLE (1 << 0) +PAD_CTL_OBE_IBE_ENABLE (3 << 0) + +Please refer to vf610-pinfunc.h in device tree source folder +for all available PIN_FUNC_ID for Vybrid VF610. diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt new file mode 100644 index 000000000000..a186181c402b --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt @@ -0,0 +1,127 @@ +ImgTec TZ1090 PDC pin controller + +Required properties: +- compatible: "img,tz1090-pdc-pinctrl" +- reg: Should contain the register physical address and length of the + SOC_GPIO_CONTROL registers in the PDC register region. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +TZ1090-PDC's pin configuration nodes act as a container for an abitrary number +of subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. For this reason, even seemingly boolean +values are actually tristates in this binding: unspecified, off, or on. +Unspecified is represented as an absent property, and off/on are represented as +integer values 0 and 1. + +Required subnode-properties: +- tz1090,pins : An array of strings. Each string contains the name of a pin or + group. Valid values for these names are listed below. + +Optional subnode-properties: +- tz1090,function: A string containing the name of the function to mux to the + pin or group. Valid values for function names are listed below, including + which pingroups can be muxed to them. +- supported generic pinconfig properties (for further details see + Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt): + - bias-disable + - bias-high-impedance + - bias-bus-hold + - bias-pull-up + - bias-pull-down + - input-schmitt-enable + - input-schmitt-disable + - drive-strength: Integer, control drive strength of pins in mA. + 2: 2mA + 4: 4mA + 8: 8mA + 12: 12mA + - low-power-enable: Flag, power-on-start weak pull-down for invalid power. + - low-power-disable: Flag, power-on-start weak pull-down disabled. + +Note that many of these properties are only valid for certain specific pins +or groups. See the TZ1090 TRM for complete details regarding which groups +support which functionality. The Linux pinctrl driver may also be a useful +reference. + +Valid values for pin and group names are: + + pins: + + These all support bias-high-impediance, bias-pull-up, bias-pull-down, and + bias-bus-hold (which can also be provided to any of the groups below to set + it for all gpio pins in that group). + + gpio0, gpio1, sys_wake0, sys_wake1, sys_wake2, ir_data, ext_power. + + mux groups: + + These all support function. + + gpio0 + pins: gpio0. + function: ir_mod_stable_out. + gpio1 + pins: gpio1. + function: ir_mod_power_out. + + drive groups: + + These support input-schmitt-enable, input-schmitt-disable, + drive-strength, low-power-enable, and low-power-disable. + + pdc + pins: gpio0, gpio1, sys_wake0, sys_wake1, sys_wake2, ir_data, + ext_power. + +Example: + + pinctrl_pdc: pinctrl@02006500 { + #gpio-range-cells = <3>; + compatible = "img,tz1090-pdc-pinctrl"; + reg = <0x02006500 0x100>; + }; + +Example board file extracts: + + &pinctrl_pdc { + pinctrl-names = "default"; + pinctrl-0 = <&syswake_default>; + + syswake_default: syswakes { + syswake_cfg { + tz1090,pins = "sys_wake0", + "sys_wake1", + "sys_wake2"; + pull-up; + }; + }; + irmod_default: irmod { + gpio0_cfg { + tz1090,pins = "gpio0"; + tz1090,function = "ir_mod_stable_out"; + }; + gpio1_cfg { + tz1090,pins = "gpio1"; + tz1090,function = "ir_mod_power_out"; + }; + }; + }; + + ir: ir@02006200 { + pinctrl-names = "default"; + pinctrl-0 = <&irmod_default>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt new file mode 100644 index 000000000000..4b27c99f7f9d --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt @@ -0,0 +1,227 @@ +ImgTec TZ1090 pin controller + +Required properties: +- compatible: "img,tz1090-pinctrl" +- reg: Should contain the register physical address and length of the pad + configuration registers (CR_PADS_* and CR_IF_CTL0). + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +TZ1090's pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. For this reason, even seemingly boolean +values are actually tristates in this binding: unspecified, off, or on. +Unspecified is represented as an absent property, and off/on are represented as +integer values 0 and 1. + +Required subnode-properties: +- tz1090,pins : An array of strings. Each string contains the name of a pin or + group. Valid values for these names are listed below. + +Optional subnode-properties: +- tz1090,function: A string containing the name of the function to mux to the + pin or group. Valid values for function names are listed below, including + which pingroups can be muxed to them. +- supported generic pinconfig properties (for further details see + Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt): + - bias-disable + - bias-high-impedance + - bias-bus-hold + - bias-pull-up + - bias-pull-down + - input-schmitt-enable + - input-schmitt-disable + - drive-strength: Integer, control drive strength of pins in mA. + 2: 2mA + 4: 4mA + 8: 8mA + 12: 12mA + + +Note that many of these properties are only valid for certain specific pins +or groups. See the TZ1090 TRM for complete details regarding which groups +support which functionality. The Linux pinctrl driver may also be a useful +reference. + +Valid values for pin and group names are: + + gpio pins: + + These all support bias-high-impediance, bias-pull-up, bias-pull-down, and + bias-bus-hold (which can also be provided to any of the groups below to set + it for all pins in that group). + + They also all support the some form of muxing. Any pins which are contained + in one of the mux groups (see below) can be muxed only to the functions + supported by the mux group. All other pins can be muxed to the "perip" + function which which enables them with their intended peripheral. + + Different pins in the same mux group cannot be muxed to different functions, + however it is possible to mux only a subset of the pins in a mux group to a + particular function and leave the remaining pins unmuxed. This is useful if + the board connects certain pins in a group to other devices to be controlled + by GPIO, and you don't want the usual peripheral to have any control of the + pin. + + ant_sel0, ant_sel1, gain0, gain1, gain2, gain3, gain4, gain5, gain6, gain7, + i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2, i2s_lrclk_out, + i2s_mclk, pa_on, pdm_a, pdm_b, pdm_c, pdm_d, pll_on, rx_hp, rx_on, + scb0_sclk, scb0_sdat, scb1_sclk, scb1_sdat, scb2_sclk, scb2_sdat, sdh_cd, + sdh_clk_in, sdh_wp, sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3, + spi0_cs0, spi0_cs1, spi0_cs2, spi0_din, spi0_dout, spi0_mclk, spi1_cs0, + spi1_cs1, spi1_cs2, spi1_din, spi1_dout, spi1_mclk, tft_blank_ls, tft_blue0, + tft_blue1, tft_blue2, tft_blue3, tft_blue4, tft_blue5, tft_blue6, tft_blue7, + tft_green0, tft_green1, tft_green2, tft_green3, tft_green4, tft_green5, + tft_green6, tft_green7, tft_hsync_nr, tft_panelclk, tft_pwrsave, tft_red0, + tft_red1, tft_red2, tft_red3, tft_red4, tft_red5, tft_red6, tft_red7, + tft_vd12acb, tft_vdden_gd, tft_vsync_ns, tx_on, uart0_cts, uart0_rts, + uart0_rxd, uart0_txd, uart1_rxd, uart1_txd. + + bias-high-impediance: supported. + bias-pull-up: supported. + bias-pull-down: supported. + bias-bus-hold: supported. + function: perip or those supported by pin's mux group. + + other pins: + + These other pins are part of various pin groups below, but can't be + controlled as GPIOs. They do however support bias-high-impediance, + bias-pull-up, bias-pull-down, and bias-bus-hold (which can also be provided + to any of the groups below to set it for all pins in that group). + + clk_out0, clk_out1, tck, tdi, tdo, tms, trst. + + bias-high-impediance: supported. + bias-pull-up: supported. + bias-pull-down: supported. + bias-bus-hold: supported. + + mux groups: + + These all support function, and some support drive configs. + + afe + pins: tx_on, rx_on, pll_on, pa_on, rx_hp, ant_sel0, + ant_sel1, gain0, gain1, gain2, gain3, gain4, + gain5, gain6, gain7. + function: afe, ts_out_0. + input-schmitt-enable: supported. + input-schmitt-disable: supported. + drive-strength: supported. + pdm_d + pins: pdm_d. + function: pdm_dac, usb_vbus. + sdh + pins: sdh_cd, sdh_wp, sdh_clk_in. + function: sdh, sdio. + sdio + pins: sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, + sdio_d3. + function: sdio, sdh. + spi1_cs2 + pins: spi1_cs2. + function: spi1_cs2, usb_vbus. + tft + pins: tft_red0, tft_red1, tft_red2, tft_red3, + tft_red4, tft_red5, tft_red6, tft_red7, + tft_green0, tft_green1, tft_green2, tft_green3, + tft_green4, tft_green5, tft_green6, tft_green7, + tft_blue0, tft_blue1, tft_blue2, tft_blue3, + tft_blue4, tft_blue5, tft_blue6, tft_blue7, + tft_vdden_gd, tft_panelclk, tft_blank_ls, + tft_vsync_ns, tft_hsync_nr, tft_vd12acb, + tft_pwrsave. + function: tft, ext_dac, not_iqadc_stb, iqdac_stb, ts_out_1, + lcd_trace, phy_ringosc. + input-schmitt-enable: supported. + input-schmitt-disable: supported. + drive-strength: supported. + + drive groups: + + These all support input-schmitt-enable, input-schmitt-disable, + and drive-strength. + + jtag + pins: tck, trst, tdi, tdo, tms. + scb1 + pins: scb1_sdat, scb1_sclk. + scb2 + pins: scb2_sdat, scb2_sclk. + spi0 + pins: spi0_mclk, spi0_cs0, spi0_cs1, spi0_cs2, spi0_dout, spi0_din. + spi1 + pins: spi1_mclk, spi1_cs0, spi1_cs1, spi1_cs2, spi1_dout, spi1_din. + uart + pins: uart0_txd, uart0_rxd, uart0_rts, uart0_cts, + uart1_txd, uart1_rxd. + drive_i2s + pins: clk_out1, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2, + i2s_lrclk_out, i2s_bclk_out, i2s_mclk. + drive_pdm + pins: clk_out0, pdm_b, pdm_a. + drive_scb0 + pins: scb0_sclk, scb0_sdat, pdm_d, pdm_c. + drive_sdio + pins: sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3, + sdh_wp, sdh_cd, sdh_clk_in. + + convenience groups: + + These are just convenient groupings of pins and don't support any drive + configs. + + uart0 + pins: uart0_cts, uart0_rts, uart0_rxd, uart0_txd. + uart1 + pins: uart1_rxd, uart1_txd. + scb0 + pins: scb0_sclk, scb0_sdat. + i2s + pins: i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2, + i2s_lrclk_out, i2s_mclk. + +Example: + + pinctrl: pinctrl@02005800 { + #gpio-range-cells = <3>; + compatible = "img,tz1090-pinctrl"; + reg = <0x02005800 0xe4>; + }; + +Example board file extract: + + &pinctrl { + uart0_default: uart0 { + uart0_cfg { + tz1090,pins = "uart0_rxd", + "uart0_txd"; + tz1090,function = "perip"; + }; + }; + tft_default: tft { + tft_cfg { + tz1090,pins = "tft"; + tz1090,function = "tft"; + }; + }; + }; + + uart@02004b00 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_default>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt index a648aaad6110..50ec3512a292 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt @@ -10,29 +10,31 @@ Required properties: Available mpp pins/groups and functions: Note: brackets (x) are not part of the mpp name for marvell,function and given only for more detailed description in this document. +Note: pmu* also allows for Power Management functions listed below name pins functions ================================================================================ -mpp0 0 gpio, pmu, uart2(rts), sdio0(cd), lcd0(pwm) -mpp1 1 gpio, pmu, uart2(cts), sdio0(wp), lcd1(pwm) +mpp0 0 gpio, pmu, uart2(rts), sdio0(cd), lcd0(pwm), pmu* +mpp1 1 gpio, pmu, uart2(cts), sdio0(wp), lcd1(pwm), pmu* mpp2 2 gpio, pmu, uart2(txd), sdio0(buspwr), sata(prsnt), - uart1(rts) + uart1(rts), pmu* mpp3 3 gpio, pmu, uart2(rxd), sdio0(ledctrl), sata(act), - uart1(cts), lcd-spi(cs1) -mpp4 4 gpio, pmu, uart3(rts), sdio1(cd), spi1(miso) -mpp5 5 gpio, pmu, uart3(cts), sdio1(wp), spi1(cs) -mpp6 6 gpio, pmu, uart3(txd), sdio1(buspwr), spi1(mosi) -mpp7 7 gpio, pmu, uart3(rxd), sdio1(ledctrl), spi1(sck) -mpp8 8 gpio, pmu, watchdog(rstout) -mpp9 9 gpio, pmu, pex1(clkreq) -mpp10 10 gpio, pmu, ssp(sclk) + uart1(cts), lcd-spi(cs1), pmu* +mpp4 4 gpio, pmu, uart3(rts), sdio1(cd), spi1(miso), pmu* +mpp5 5 gpio, pmu, uart3(cts), sdio1(wp), spi1(cs), pmu* +mpp6 6 gpio, pmu, uart3(txd), sdio1(buspwr), spi1(mosi), pmu* +mpp7 7 gpio, pmu, uart3(rxd), sdio1(ledctrl), spi1(sck), pmu* +mpp8 8 gpio, pmu, watchdog(rstout), pmu* +mpp9 9 gpio, pmu, pex1(clkreq), pmu* +mpp10 10 gpio, pmu, ssp(sclk), pmu* mpp11 11 gpio, pmu, sata(prsnt), sata-1(act), sdio0(ledctrl), - sdio1(ledctrl), pex0(clkreq) -mpp12 12 gpio, pmu, uart2(rts), audio0(extclk), sdio1(cd), sata(act) + sdio1(ledctrl), pex0(clkreq), pmu* +mpp12 12 gpio, pmu, uart2(rts), audio0(extclk), sdio1(cd), + sata(act), pmu* mpp13 13 gpio, pmu, uart2(cts), audio1(extclk), sdio1(wp), - ssp(extclk) -mpp14 14 gpio, pmu, uart2(txd), sdio1(buspwr), ssp(rxd) -mpp15 15 gpio, pmu, uart2(rxd), sdio1(ledctrl), ssp(sfrm) + ssp(extclk), pmu* +mpp14 14 gpio, pmu, uart2(txd), sdio1(buspwr), ssp(rxd), pmu* +mpp15 15 gpio, pmu, uart2(rxd), sdio1(ledctrl), ssp(sfrm), pmu* mpp16 16 gpio, uart3(rts), sdio0(cd), ac97(sdi1), lcd-spi(cs1) mpp17 17 gpio, uart3(cts), sdio0(wp), ac97(sdi2), twsi(sda), ac97-1(sysclko) @@ -57,6 +59,21 @@ mpp_nand 64-71 gpo, nand audio0 - i2s, ac97 twsi - none, opt1, opt2, opt3 +Power Management functions (pmu*): +pmu-nc Pin not driven by any PM function +pmu-low Pin driven low (0) +pmu-high Pin driven high (1) +pmic(sdi) Pin is used for PMIC SDI +cpu-pwr-down Pin is used for CPU_PWRDWN +standby-pwr-down Pin is used for STBY_PWRDWN +core-pwr-good Pin is used for CORE_PWR_GOOD (Pins 0-7 only) +cpu-pwr-good Pin is used for CPU_PWR_GOOD (Pins 8-15 only) +bat-fault Pin is used for BATTERY_FAULT +ext0-wakeup Pin is used for EXT0_WU +ext1-wakeup Pin is used for EXT0_WU +ext2-wakeup Pin is used for EXT0_WU +pmu-blink Pin is used for blink function + Notes: * group "mpp_audio1" allows the following functions and gpio pins: - gpio : gpio on pins 52-57 diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index c95ea8278f87..aeb3c995cc04 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -126,3 +126,51 @@ device; they may be grandchildren, for example. Whether this is legal, and whether there is any interaction between the child and intermediate parent nodes, is again defined entirely by the binding for the individual pin controller device. + +== Using generic pinconfig options == + +Generic pinconfig parameters can be used by defining a separate node containing +the applicable parameters (and optional values), like: + +pcfg_pull_up: pcfg_pull_up { + bias-pull-up; + drive-strength = <20>; +}; + +This node should then be referenced in the appropriate pinctrl node as a phandle +and parsed in the driver using the pinconf_generic_parse_dt_config function. + +Supported configuration parameters are: + +bias-disable - disable any pin bias +bias-high-impedance - high impedance mode ("third-state", "floating") +bias-bus-hold - latch weakly +bias-pull-up - pull up the pin +bias-pull-down - pull down the pin +bias-pull-pin-default - use pin-default pull state +drive-push-pull - drive actively high and low +drive-open-drain - drive with open drain +drive-open-source - drive with open source +drive-strength - sink or source at most X mA +input-schmitt-enable - enable schmitt-trigger mode +input-schmitt-disable - disable schmitt-trigger mode +input-debounce - debounce mode with debound time X +low-power-enable - enable low power mode +low-power-disable - disable low power mode +output-low - set the pin to output mode with low level +output-high - set the pin to output mode with high level + +Arguments for parameters: + +- bias-pull-up, -down and -pin-default take as optional argument on hardware + supporting it the pull strength in Ohm. bias-disable will disable the pull. + +- drive-strength takes as argument the target strength in mA. + +- input-debounce takes the debounce time in usec as argument + or 0 to disable debouncing + +All parameters not listed here, do not take an argument. + +More in-depth documentation on these parameters can be found in +<include/linux/pinctrl/pinconfig-generic.h> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt index 08f0c3d01575..5a02e30dd262 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt @@ -18,7 +18,8 @@ Optional properties: pin functions is ignored - pinctrl-single,bit-per-mux : boolean to indicate that one register controls - more than one pin + more than one pin, for which "pinctrl-single,function-mask" property specifies + position mask of pin. - pinctrl-single,drive-strength : array of value that are used to configure drive strength in the pinmux register. They're value of drive strength diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt new file mode 100644 index 000000000000..05bf82a07dfd --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt @@ -0,0 +1,110 @@ +*ST pin controller. + +Each multi-function pin is controlled, driven and routed through the +PIO multiplexing block. Each pin supports GPIO functionality (ALT0) +and multiple alternate functions(ALT1 - ALTx) that directly connect +the pin to different hardware blocks. + +When a pin is in GPIO mode, Output Enable (OE), Open Drain(OD), and +Pull Up (PU) are driven by the related PIO block. + +ST pinctrl driver controls PIO multiplexing block and also interacts with +gpio driver to configure a pin. + +Required properties: (PIO multiplexing block) +- compatible : should be "st,<SOC>-<pio-block>-pinctrl" + like st,stih415-sbc-pinctrl, st,stih415-front-pinctrl and so on. +- gpio-controller : Indicates this device is a GPIO controller +- #gpio-cells : Should be one. The first cell is the pin number. +- st,retime-pin-mask : Should be mask to specify which pins can be retimed. + If the property is not present, it is assumed that all the pins in the + bank are capable of retiming. Retiming is mainly used to improve the + IO timing margins of external synchronous interfaces. +- st,bank-name : Should be a name string for this bank as + specified in datasheet. +- st,syscfg : Should be a phandle of the syscfg node. + +Example: + pin-controller-sbc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stih415-sbc-pinctrl"; + st,syscfg = <&syscfg_sbc>; + ranges = <0 0xfe610000 0x5000>; + PIO0: gpio@fe610000 { + gpio-controller; + #gpio-cells = <1>; + reg = <0 0x100>; + st,bank-name = "PIO0"; + }; + ... + pin-functions nodes follow... + }; + + +Contents of function subnode node: +---------------------- +Required properties for pin configuration node: +- st,pins : Child node with list of pins with configuration. + +Below is the format of how each pin conf should look like. + +<bank offset mux mode rt_type rt_delay rt_clk> + +Every PIO is represented with 4-7 parameters depending on retime configuration. +Each parameter is explained as below. + +-bank : Should be bank phandle to which this PIO belongs. +-offset : Offset in the PIO bank. +-mux : Should be alternate function number associated this pin. + Use same numbers from datasheet. +-mode :pin configuration is selected from one of the below values. + IN + IN_PU + OUT + BIDIR + BIDIR_PU + +-rt_type Retiming Configuration for the pin. + Possible retime configuration are: + + ------- ------------- + value args + ------- ------------- + NICLK <delay> <clk> + ICLK_IO <delay> <clk> + BYPASS <delay> + DE_IO <delay> <clk> + SE_ICLK_IO <delay> <clk> + SE_NICLK_IO <delay> <clk> + +- delay is retime delay in pico seconds as mentioned in data sheet. + +- rt_clk :clk to be use for retime. + Possible values are: + CLK_A + CLK_B + CLK_C + CLK_D + +Example of mmcclk pin which is a bi-direction pull pu with retime config +as non inverted clock retimed with CLK_B and delay of 0 pico seconds: + +pin-controller { + ... + mmc0 { + pinctrl_mmc: mmc { + st,pins { + mmcclk = <&PIO13 4 ALT4 BIDIR_PU NICLK 0 CLK_B>; + ... + }; + }; + ... + }; +}; + +sdhci0:sdhci@fe810000{ + ... + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc>; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt new file mode 100644 index 000000000000..d5dac7b843a9 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -0,0 +1,153 @@ +* Renesas Pin Function Controller (GPIO and Pin Mux/Config) + +The Pin Function Controller (PFC) is a Pin Mux/Config controller. On SH7372, +SH73A0, R8A73A4 and R8A7740 it also acts as a GPIO controller. + + +Pin Control +----------- + +Required Properties: + + - compatible: should be one of the following. + - "renesas,pfc-r8a73a4": for R8A73A4 (R-Mobile APE6) compatible pin-controller. + - "renesas,pfc-r8a7740": for R8A7740 (R-Mobile A1) compatible pin-controller. + - "renesas,pfc-r8a7778": for R8A7778 (R-Mobile M1) compatible pin-controller. + - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller. + - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller. + - "renesas,pfc-sh7372": for SH7372 (SH-Mobile AP4) compatible pin-controller. + - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller. + + - reg: Base address and length of each memory resource used by the pin + controller hardware module. + +Optional properties: + + - #gpio-range-cells: Mandatory when the PFC doesn't handle GPIO, forbidden + otherwise. Should be 3. + +The PFC node also acts as a container for pin configuration nodes. Please refer +to pinctrl-bindings.txt in this directory for the definition of the term "pin +configuration node" and for the common pinctrl bindings used by client devices. + +Each pin configuration node represents a desired configuration for a pin, a +pin group, or a list of pins or pin groups. The configuration can include the +function to select on those pin(s) and pin configuration parameters (such as +pull-up and pull-down). + +Pin configuration nodes contain pin configuration properties, either directly +or grouped in child subnodes. Both pin muxing and configuration parameters can +be grouped in that way and referenced as a single pin configuration node by +client devices. + +A configuration node or subnode must reference at least one pin (through the +pins or pin groups properties) and contain at least a function or one +configuration parameter. When the function is present only pin groups can be +used to reference pins. + +All pin configuration nodes and subnodes names are ignored. All of those nodes +are parsed through phandles and processed purely based on their content. + +Pin Configuration Node Properties: + +- renesas,pins : An array of strings, each string containing the name of a pin. +- renesas,groups : An array of strings, each string containing the name of a pin + group. + +- renesas,function: A string containing the name of the function to mux to the + pin group(s) specified by the renesas,groups property + + Valid values for pin, group and function names can be found in the group and + function arrays of the PFC data file corresponding to the SoC + (drivers/pinctrl/sh-pfc/pfc-*.c) + +The pin configuration parameters use the generic pinconf bindings defined in +pinctrl-bindings.txt in this directory. The supported parameters are +bias-disable, bias-pull-up and bias-pull-down. + + +GPIO +---- + +On SH7372, SH73A0, R8A73A4 and R8A7740 the PFC node is also a GPIO controller +node. + +Required Properties: + + - gpio-controller: Marks the device node as a gpio controller. + + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the + GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. + +The syntax of the gpio specifier used by client nodes should be the following +with values derived from the SoC user manual. + + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [flags]> + +On other mach-shmobile platforms GPIO is handled by the gpio-rcar driver. +Please refer to Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +for documentation of the GPIO device tree bindings on those platforms. + + +Examples +-------- + +Example 1: SH73A0 (SH-Mobile AG5) pin controller node + + pfc: pfc@e6050000 { + compatible = "renesas,pfc-sh73a0"; + reg = <0xe6050000 0x8000>, + <0xe605801c 0x1c>; + gpio-controller; + #gpio-cells = <2>; + }; + +Example 2: A GPIO LED node that references a GPIO + + #include <dt-bindings/gpio/gpio.h> + + leds { + compatible = "gpio-leds"; + led1 { + gpios = <&pfc 20 GPIO_ACTIVE_LOW>; + }; + }; + +Example 3: KZM-A9-GT (SH-Mobile AG5) default pin state hog and pin control maps + for the MMCIF and SCIFA4 devices + + &pfc { + pinctrl-0 = <&scifa4_pins>; + pinctrl-names = "default"; + + mmcif_pins: mmcif { + mux { + renesas,groups = "mmc0_data8_0", "mmc0_ctrl_0"; + renesas,function = "mmc0"; + }; + cfg { + renesas,groups = "mmc0_data8_0"; + renesas,pins = "PORT279"; + bias-pull-up; + }; + }; + + scifa4_pins: scifa4 { + renesas,groups = "scifa4_data", "scifa4_ctrl"; + renesas,function = "scifa4"; + }; + }; + +Example 4: KZM-A9-GT (SH-Mobile AG5) default pin state for the MMCIF device + + &mmcif { + pinctrl-0 = <&mmcif_pins>; + pinctrl-names = "default"; + + bus-width = <8>; + vmmc-supply = <®_1p8v>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt new file mode 100644 index 000000000000..b0fb1018d7ad --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -0,0 +1,97 @@ +* Rockchip Pinmux Controller + +The Rockchip Pinmux Controller, enables the IC +to share one PAD to several functional blocks. The sharing is done by +multiplexing the PAD input/output signals. For each PAD there are up to +4 muxing options with option 0 being the use as a GPIO. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The Rockchip pin configuration node is a node of a group of pins which can be +used for a specific device or function. This node represents both mux and +config of the pins in that group. The 'pins' selects the function mode(also +named pin mode) this pin can work on and the 'config' configures various pad +settings such as pull-up, etc. + +The pins are grouped into up to 5 individual pin banks which need to be +defined as gpio sub-nodes of the pinmux controller. + +Required properties for iomux controller: + - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl" + "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl" + +Required properties for gpio sub nodes: + - compatible: "rockchip,gpio-bank" + - reg: register of the gpio bank (different than the iomux registerset) + - interrupts: base interrupt of the gpio bank in the interrupt controller + - clocks: clock that drives this bank + - gpio-controller: identifies the node as a gpio controller and pin bank. + - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO + binding is used, the amount of cells must be specified as 2. See generic + GPIO binding documentation for description of particular cells. + - interrupt-controller: identifies the controller node as interrupt-parent. + - #interrupt-cells: the value of this property should be 2 and the interrupt + cells should use the standard two-cell scheme described in + bindings/interrupt-controller/interrupts.txt + +Required properties for pin configuration node: + - rockchip,pins: 3 integers array, represents a group of pins mux and config + setting. The format is rockchip,pins = <PIN_BANK PIN_BANK_IDX MUX &phandle>. + The MUX 0 means gpio and MUX 1 to 3 mean the specific device function. + The phandle of a node containing the generic pinconfig options + to use, as described in pinctrl-bindings.txt in this directory. + +Examples: + +#include <dt-bindings/pinctrl/rockchip.h> + +... + +pinctrl@20008000 { + compatible = "rockchip,rk3066a-pinctrl"; + reg = <0x20008000 0x150>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gpio0: gpio0@20034000 { + compatible = "rockchip,gpio-bank"; + reg = <0x20034000 0x100>; + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_gates8 9>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + ... + + pcfg_pull_default: pcfg_pull_default { + bias-pull-pin-default + }; + + uart2 { + uart2_xfer: uart2-xfer { + rockchip,pins = <RK_GPIO1 8 1 &pcfg_pull_default>, + <RK_GPIO1 9 1 &pcfg_pull_default>; + }; + }; +}; + +uart2: serial@20064000 { + compatible = "snps,dw-apb-uart"; + reg = <0x20064000 0x400>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&mux_uart2>; + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&uart2_xfer>; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/ste,abx500.txt b/Documentation/devicetree/bindings/pinctrl/ste,abx500.txt new file mode 100644 index 000000000000..e3865e136067 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ste,abx500.txt @@ -0,0 +1,352 @@ +ST Ericsson abx500 pinmux controller + +Required properties: +- compatible: "stericsson,ab8500-gpio", "stericsson,ab8540-gpio", + "stericsson,ab8505-gpio", "stericsson,ab9540-gpio", + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +ST Ericsson's pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as input, output, pull up, pull down... + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Required subnode-properties: +- ste,pins : An array of strings. Each string contains the name of a pin or + group. + +Optional subnode-properties: +- ste,function: A string containing the name of the function to mux to the + pin or group. + +- generic pin configuration option to use. Example : + + default_cfg { + ste,pins = "GPIO1"; + bias-disable; + }; + +- ste,config: Handle of pin configuration node containing the generic + pinconfig options to use, as described in pinctrl-bindings.txt in + this directory. Example : + + pcfg_bias_disable: pcfg_bias_disable { + bias-disable; + }; + + default_cfg { + ste,pins = "GPIO1"; + ste.config = <&pcfg_bias_disable>; + }; + +Example board file extract: + +&pinctrl_abx500 { + pinctrl-names = "default"; + pinctrl-0 = <&sysclkreq2_default_mode>, <&sysclkreq3_default_mode>, <&gpio3_default_mode>, <&sysclkreq6_default_mode>, <&pwmout1_default_mode>, <&pwmout2_default_mode>, <&pwmout3_default_mode>, <&adi1_default_mode>, <&dmic12_default_mode>, <&dmic34_default_mode>, <&dmic56_default_mode>, <&sysclkreq5_default_mode>, <&batremn_default_mode>, <&service_default_mode>, <&pwrctrl0_default_mode>, <&pwrctrl1_default_mode>, <&pwmextvibra1_default_mode>, <&pwmextvibra2_default_mode>, <&gpio51_default_mode>, <&gpio52_default_mode>, <&gpio53_default_mode>, <&gpio54_default_mode>, <&pdmclkdat_default_mode>; + + sysclkreq2 { + sysclkreq2_default_mode: sysclkreq2_default { + default_mux { + ste,function = "sysclkreq"; + ste,pins = "sysclkreq2_d_1"; + }; + default_cfg { + ste,pins = "GPIO1"; + bias-disable; + }; + }; + }; + sysclkreq3 { + sysclkreq3_default_mode: sysclkreq3_default { + default_mux { + ste,function = "sysclkreq"; + ste,pins = "sysclkreq3_d_1"; + }; + default_cfg { + ste,pins = "GPIO2"; + output-low; + }; + }; + }; + gpio3 { + gpio3_default_mode: gpio3_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio3_a_1"; + }; + default_cfg { + ste,pins = "GPIO3"; + output-low; + }; + }; + }; + sysclkreq6 { + sysclkreq6_default_mode: sysclkreq6_default { + default_mux { + ste,function = "sysclkreq"; + ste,pins = "sysclkreq6_d_1"; + }; + default_cfg { + ste,pins = "GPIO4"; + bias-disable; + }; + }; + }; + pwmout1 { + pwmout1_default_mode: pwmout1_default { + default_mux { + ste,function = "pwmout"; + ste,pins = "pwmout1_d_1"; + }; + default_cfg { + ste,pins = "GPIO14"; + output-low; + }; + }; + }; + pwmout2 { + pwmout2_default_mode: pwmout2_default { + pwmout2_default_mux { + ste,function = "pwmout"; + ste,pins = "pwmout2_d_1"; + }; + pwmout2_default_cfg { + ste,pins = "GPIO15"; + output-low; + }; + }; + }; + pwmout3 { + pwmout3_default_mode: pwmout3_default { + pwmout3_default_mux { + ste,function = "pwmout"; + ste,pins = "pwmout3_d_1"; + }; + pwmout3_default_cfg { + ste,pins = "GPIO16"; + output-low; + }; + }; + }; + adi1 { + + adi1_default_mode: adi1_default { + adi1_default_mux { + ste,function = "adi1"; + ste,pins = "adi1_d_1"; + }; + adi1_default_cfg1 { + ste,pins = "GPIO17","GPIO19","GPIO20"; + bias-disable; + }; + adi1_default_cfg2 { + ste,pins = "GPIO18"; + output-low; + }; + }; + }; + dmic12 { + dmic12_default_mode: dmic12_default { + dmic12_default_mux { + ste,function = "dmic"; + ste,pins = "dmic12_d_1"; + }; + dmic12_default_cfg1 { + ste,pins = "GPIO27"; + output-low; + }; + dmic12_default_cfg2 { + ste,pins = "GPIO28"; + bias-disable; + }; + }; + }; + dmic34 { + dmic34_default_mode: dmic34_default { + dmic34_default_mux { + ste,function = "dmic"; + ste,pins = "dmic34_d_1"; + }; + dmic34_default_cfg1 { + ste,pins = "GPIO29"; + output-low; + }; + dmic34_default_cfg2 { + ste,pins = "GPIO30"; + bias-disable;{ + + }; + }; + }; + dmic56 { + dmic56_default_mode: dmic56_default { + dmic56_default_mux { + ste,function = "dmic"; + ste,pins = "dmic56_d_1"; + }; + dmic56_default_cfg1 { + ste,pins = "GPIO31"; + output-low; + }; + dmic56_default_cfg2 { + ste,pins = "GPIO32"; + bias-disable; + }; + }; + }; + sysclkreq5 { + sysclkreq5_default_mode: sysclkreq5_default { + sysclkreq5_default_mux { + ste,function = "sysclkreq"; + ste,pins = "sysclkreq5_d_1"; + }; + sysclkreq5_default_cfg { + ste,pins = "GPIO42"; + output-low; + }; + }; + }; + batremn { + batremn_default_mode: batremn_default { + batremn_default_mux { + ste,function = "batremn"; + ste,pins = "batremn_d_1"; + }; + batremn_default_cfg { + ste,pins = "GPIO43"; + bias-disable; + }; + }; + }; + service { + service_default_mode: service_default { + service_default_mux { + ste,function = "service"; + ste,pins = "service_d_1"; + }; + service_default_cfg { + ste,pins = "GPIO44"; + bias-disable; + }; + }; + }; + pwrctrl0 { + pwrctrl0_default_mux: pwrctrl0_mux { + pwrctrl0_default_mux { + ste,function = "pwrctrl"; + ste,pins = "pwrctrl0_d_1"; + }; + }; + pwrctrl0_default_mode: pwrctrl0_default { + pwrctrl0_default_cfg { + ste,pins = "GPIO45"; + bias-disable; + }; + }; + }; + pwrctrl1 { + pwrctrl1_default_mux: pwrctrl1_mux { + pwrctrl1_default_mux { + ste,function = "pwrctrl"; + ste,pins = "pwrctrl1_d_1"; + }; + }; + pwrctrl1_default_mode: pwrctrl1_default { + pwrctrl1_default_cfg { + ste,pins = "GPIO46"; + bias-disable; + }; + }; + }; + pwmextvibra1 { + pwmextvibra1_default_mode: pwmextvibra1_default { + pwmextvibra1_default_mux { + ste,function = "pwmextvibra"; + ste,pins = "pwmextvibra1_d_1"; + }; + pwmextvibra1_default_cfg { + ste,pins = "GPIO47"; + bias-disable; + }; + }; + }; + pwmextvibra2 { + pwmextvibra2_default_mode: pwmextvibra2_default { + pwmextvibra2_default_mux { + ste,function = "pwmextvibra"; + ste,pins = "pwmextvibra2_d_1"; + }; + pwmextvibra1_default_cfg { + ste,pins = "GPIO48"; + bias-disable; + }; + }; + }; + gpio51 { + gpio51_default_mode: gpio51_default { + gpio51_default_mux { + ste,function = "gpio"; + ste,pins = "gpio51_a_1"; + }; + gpio51_default_cfg { + ste,pins = "GPIO51"; + output-low; + }; + }; + }; + gpio52 { + gpio52_default_mode: gpio52_default { + gpio52_default_mux { + ste,function = "gpio"; + ste,pins = "gpio52_a_1"; + }; + gpio52_default_cfg { + ste,pins = "GPIO52"; + bias-pull-down; + }; + }; + }; + gpio53 { + gpio53_default_mode: gpio53_default { + gpio53_default_mux { + ste,function = "gpio"; + ste,pins = "gpio53_a_1"; + }; + gpio53_default_cfg { + ste,pins = "GPIO53"; + bias-pull-down; + }; + }; + }; + gpio54 { + gpio54_default_mode: gpio54_default { + gpio54_default_mux { + ste,function = "gpio"; + ste,pins = "gpio54_a_1"; + }; + gpio54_default_cfg { + ste,pins = "GPIO54"; + output-low; + }; + }; + }; + pdmclkdat { + pdmclkdat_default_mode: pdmclkdat_default { + pdmclkdat_default_mux { + ste,function = "pdm"; + ste,pins = "pdmclkdat_d_1"; + }; + pdmclkdat_default_cfg { + ste,pins = "GPIO55", "GPIO56"; + bias-disable; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/pps/pps-gpio.txt b/Documentation/devicetree/bindings/pps/pps-gpio.txt new file mode 100644 index 000000000000..40bf9c3564a5 --- /dev/null +++ b/Documentation/devicetree/bindings/pps/pps-gpio.txt @@ -0,0 +1,20 @@ +Device-Tree Bindings for a PPS Signal on GPIO + +These properties describe a PPS (pulse-per-second) signal connected to +a GPIO pin. + +Required properties: +- compatible: should be "pps-gpio" +- gpios: one PPS GPIO in the format described by ../gpio/gpio.txt + +Optional properties: +- assert-falling-edge: when present, assert is indicated by a falling edge + (instead of by a rising edge) + +Example: + pps { + compatible = "pps-gpio"; + gpios = <&gpio2 6 0>; + + assert-falling-edge; + }; diff --git a/Documentation/devicetree/bindings/regulator/lp872x.txt b/Documentation/devicetree/bindings/regulator/lp872x.txt new file mode 100644 index 000000000000..78183182dad9 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/lp872x.txt @@ -0,0 +1,160 @@ +Binding for TI/National Semiconductor LP872x Driver + +Required properties: + - compatible: "ti,lp8720" or "ti,lp8725" + - reg: I2C slave address. 0x7d = LP8720, 0x7a = LP8725 + +Optional properties: + - ti,general-config: the value of LP872X_GENERAL_CFG register (u8) + (LP8720) + bit[2]: BUCK output voltage control by external DVS pin or register + 1 = external pin, 0 = bit7 of register 08h + bit[1]: sleep control by external DVS pin or register + 1 = external pin, 0 = bit6 of register 08h + bit[0]: time step unit(usec). 1 = 25, 0 = 50 + + (LP8725) + bit[7:6]: time step unit(usec). 00 = 32, 01 = 64, 10 = 128, 11 = 256 + bit[4]: BUCK2 enable control. 1 = enable, 0 = disable + bit[3]: BUCK2 output voltage register address. 1 = 0Ah, 0 = 0Bh + bit[2]: BUCK1 output voltage control by external DVS pin or register + 1 = register 08h, 0 = DVS + bit[1]: LDO sleep control. 1 = sleep mode, 0 = normal + bit[0]: BUCK1 enable control, 1 = enable, 0 = disable + + For more details, please see the datasheet. + + - ti,update-config: define it when LP872X_GENERAL_CFG register should be set + - ti,dvs-gpio: GPIO specifier for external DVS pin control of LP872x devices. + - ti,dvs-vsel: DVS selector. 0 = SEL_V1, 1 = SEL_V2. + - ti,dvs-state: initial DVS pin state. 0 = DVS_LOW, 1 = DVS_HIGH. + + Sub nodes for regulator_init_data + LP8720 has maximum 6 nodes. (child name: ldo1 ~ 5 and buck) + LP8725 has maximum 9 nodes. (child name: ldo1 ~ 5, lilo1,2 and buck1,2) + For more details, please see the following binding document. + (Documentation/devicetree/bindings/regulator/regulator.txt) + +Datasheet + - LP8720: http://www.ti.com/lit/ds/symlink/lp8720.pdf + - LP8725: http://www.ti.com/lit/ds/symlink/lp8725.pdf + +Example 1) LP8720 + +lp8720@7d { + compatible = "ti,lp8720"; + reg = <0x7d>; + + /* external DVS pin used, timestep is 25usec */ + ti,general-config = /bits/ 8 <0x03>; + ti,update-config; + + /* + * The dvs-gpio depends on the processor environment. + * For example, following GPIO specifier means GPIO134 in OMAP4. + */ + ti,dvs-gpio = <&gpio5 6 0>; + ti,dvs-vsel = /bits/ 8 <1>; /* SEL_V2 */ + ti,dvs-state = /bits/ 8 <1>; /* DVS_HIGH */ + + vaf: ldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vmmc: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcam_io: ldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + vcam_core: ldo4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <2850000>; + regulator-boot-on; + }; + + vcam: ldo5 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcc: buck { + regulator-name = "VBUCK"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <2300000>; + }; +}; + +Example 2) LP8725 + +lp8725@7a { + compatible = "ti,lp8725"; + reg = <0x7a>; + + /* Enable BUCK1,2, no DVS, normal LDO mode, timestep is 256usec */ + ti,general-config = /bits/ 8 <0xdd>; + ti,update-config; + + vcam_io: ldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcam_core: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcam: ldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcmmb_io: ldo4 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + vcmmb_core: ldo5 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + vaux1: lilo1 { + regulator-name = "VAUX1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + vaux2: lilo2 { + regulator-name = "VAUX2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + vcc1: buck1 { + regulator-name = "VBUCK1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3000000>; + regulator-min-microamp = <460000>; + regulator-max-microamp = <1370000>; + regulator-boot-on; + }; + + vcc2: buck2 { + regulator-name = "VBUCK2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3000000>; + regulator-min-microamp = <460000>; + regulator-max-microamp = <1370000>; + regulator-boot-on; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/max8973-regulator.txt b/Documentation/devicetree/bindings/regulator/max8973-regulator.txt new file mode 100644 index 000000000000..4f15d8a1bfd0 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8973-regulator.txt @@ -0,0 +1,21 @@ +* Maxim MAX8973 Voltage Regulator + +Required properties: + +- compatible: must be "maxim,max8973" +- reg: the i2c slave address of the regulator. It should be 0x1b. + +Any standard regulator properties can be used to configure the single max8973 +DCDC. + +Example: + + max8973@1b { + compatible = "maxim,max8973"; + reg = <0x1b>; + + regulator-min-microvolt = <935000>; + regulator-max-microvolt = <1200000>; + regulator-boot-on; + regulator-always-on; + }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index ecfc6ccd67ef..48a3b8e5d6bd 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -9,6 +9,7 @@ Optional properties: - regulator-max-microamp: largest current consumers may set - regulator-always-on: boolean, regulator should never be disabled - regulator-boot-on: bootloader/firmware enabled regulator +- regulator-allow-bypass: allow the regulator to go into bypass mode - <name>-supply: phandle to the parent supply/regulator node - regulator-ramp-delay: ramp delay for regulator(in uV/uS) diff --git a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt new file mode 100644 index 000000000000..2e57a33e9029 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt @@ -0,0 +1,128 @@ +Adaptive Body Bias(ABB) SoC internal LDO regulator for Texas Instruments SoCs + +Required Properties: +- compatible: Should be one of: + - "ti,abb-v1" for older SoCs like OMAP3 + - "ti,abb-v2" for newer SoCs like OMAP4, OMAP5 +- reg: Address and length of the register set for the device. It contains + the information of registers in the same order as described by reg-names +- reg-names: Should contain the reg names + - "base-address" - contains base address of ABB module + - "int-address" - contains address of interrupt register for ABB module + (also see Optional properties) +- #address-cell: should be 0 +- #size-cell: should be 0 +- clocks: should point to the clock node used by ABB module +- ti,settling-time: Settling time in uSecs from SoC documentation for ABB module + to settle down(target time for SR2_WTCNT_VALUE). +- ti,clock-cycles: SoC specific data about count of system ti,clock-cycles used for + computing settling time from SoC Documentation for ABB module(clock + cycles for SR2_WTCNT_VALUE). +- ti,tranxdone-status-mask: Mask to the int-register to write-to-clear mask + indicating LDO tranxdone (operation complete). +- ti,abb_info: An array of 6-tuples u32 items providing information about ABB + configuration needed per operational voltage of the device. + Each item consists of the following in the same order: + volt: voltage in uV - Only used to index ABB information. + ABB mode: one of the following: + 0-bypass + 1-Forward Body Bias(FBB) + 3-Reverse Body Bias(RBB) + efuse: (see Optional properties) + RBB enable efuse Mask: (See Optional properties) + FBB enable efuse Mask: (See Optional properties) + Vset value efuse Mask: (See Optional properties) + + NOTE: If more than 1 entry is present, then regulator is setup to change + voltage, allowing for various modes to be selected indexed off + the regulator. Further, ABB LDOs are considered always-on by + default. + +Optional Properties: +- reg-names: In addition to the required properties, the following are optional + - "efuse-address" - Contains efuse base address used to pick up ABB info. + - "ldo-address" - Contains address of ABB LDO overide register address. + "efuse-address" is required for this. +- ti,ldovbb-vset-mask - Required if ldo-address is set, mask for LDO override + register to provide override vset value. +- ti,ldovbb-override-mask - Required if ldo-address is set, mask for LDO + override register to enable override vset value. +- ti,abb_opp_sel: Addendum to the description in required properties + efuse: Mandatory if 'efuse-address' register is defined. Provides offset + from efuse-address to pick up ABB characteristics. Set to 0 if + 'efuse-address' is not defined. + RBB enable efuse Mask: Optional if 'efuse-address' register is defined. + 'ABB mode' is force set to RBB mode if value at "efuse-address" + + efuse maps to RBB mask. Set to 0 to ignore this. + FBB enable efuse Mask: Optional if 'efuse-address' register is defined. + 'ABB mode' is force set to FBB mode if value at "efuse-address" + + efuse maps to FBB mask (valid only if RBB mask does not match) + Set to 0 to ignore this. + Vset value efuse Mask: Mandatory if ldo-address is set. Picks up from + efuse the value to set in 'ti,ldovbb-vset-mask' at ldo-address. + +Example #1: Simplest configuration (no efuse data, hard coded ABB table): +abb_x: regulator-abb-x { + compatible = "ti,abb-v1"; + regulator-name = "abb_x"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x483072f0 0x8>, <0x48306818 0x4>; + reg-names = "base-address", "int-address"; + ti,tranxdone-status-mask = <0x4000000>; + clocks = <&sysclk>; + ti,settling-time = <30>; + ti,clock-cycles = <8>; + ti,abb_info = < + /* uV ABB efuse rbb_m fbb_m vset_m */ + 1012500 0 0 0 0 0 /* Bypass */ + 1200000 3 0 0 0 0 /* RBB mandatory */ + 1320000 1 0 0 0 0 /* FBB mandatory */ + >; +}; + +Example #2: Efuse bits contain ABB mode setting (no LDO override capability) +abb_y: regulator-abb-y { + compatible = "ti,abb-v2"; + regulator-name = "abb_y"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x4a307bd0 0x8>, <0x4a306014 0x4>, <0x4A002268 0x8>; + reg-names = "base-address", "int-address", "efuse-address"; + ti,tranxdone-status-mask = <0x4000000>; + clocks = <&sysclk>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + ti,abb_info = < + /* uV ABB efuse rbb_m fbb_m vset_m */ + 975000 0 0 0 0 0 /* Bypass */ + 1012500 0 0 0x40000 0 0 /* RBB optional */ + 1200000 0 0x4 0 0x40000 0 /* FBB optional */ + 1320000 1 0 0 0 0 /* FBB mandatory */ + >; +}; + +Example #3: Efuse bits contain ABB mode setting and LDO override capability +abb_z: regulator-abb-z { + compatible = "ti,abb-v2"; + regulator-name = "abb_z"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>, + <0x4a002194 0x8>, <0x4ae0C314 0x4>; + reg-names = "base-address", "int-address", + "efuse-address", "ldo-address"; + ti,tranxdone-status-mask = <0x8000000>; + /* LDOVBBMM_MUX_CTRL */ + ti,ldovbb-override-mask = <0x400>; + /* LDOVBBMM_VSET_OUT */ + ti,ldovbb-vset-mask = <0x1F>; + clocks = <&sysclk>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + ti,abb_info = < + /* uV ABB efuse rbb_m fbb_m vset_m */ + 975000 0 0 0 0 0 /* Bypass */ + 1200000 0 0x4 0 0x40000 0x1f00 /* FBB optional, vset */ + >; +}; diff --git a/Documentation/devicetree/bindings/sound/adi,adau1701.txt b/Documentation/devicetree/bindings/sound/adi,adau1701.txt new file mode 100644 index 000000000000..547a49b56a62 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/adi,adau1701.txt @@ -0,0 +1,35 @@ +Analog Devices ADAU1701 + +Required properties: + + - compatible: Should contain "adi,adau1701" + - reg: The i2c address. Value depends on the state of ADDR0 + and ADDR1, as wired in hardware. + +Optional properties: + + - reset-gpio: A GPIO spec to define which pin is connected to the + chip's !RESET pin. If specified, the driver will + assert a hardware reset at probe time. + - adi,pll-mode-gpios: An array of two GPIO specs to describe the GPIOs + the ADAU's PLL config pins are connected to. + The state of the pins are set according to the + configured clock divider on ASoC side before the + firmware is loaded. + - adi,pin-config: An array of 12 numerical values selecting one of the + pin configurations as described in the datasheet, + table 53. Note that the value of this property has + to be prefixed with '/bits/ 8'. + +Examples: + + i2c_bus { + adau1701@34 { + compatible = "adi,adau1701"; + reg = <0x34>; + reset-gpio = <&gpio 23 0>; + adi,pll-mode-gpios = <&gpio 24 0 &gpio 25 0>; + adi,pin-config = /bits/ 8 <0x4 0x7 0x5 0x5 0x4 0x4 + 0x4 0x4 0x4 0x4 0x4 0x4>; + }; + }; diff --git a/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt b/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt new file mode 100644 index 000000000000..f49450a87890 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt @@ -0,0 +1,46 @@ +Freescale i.MX audio complex with WM8962 codec + +Required properties: +- compatible : "fsl,imx-audio-wm8962" +- model : The user-visible name of this sound complex +- ssi-controller : The phandle of the i.MX SSI controller +- audio-codec : The phandle of the WM8962 audio codec +- audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names could be power + supplies, WM8962 pins, and the jacks on the board: + + Power supplies: + * Mic Bias + + Board connectors: + * Mic Jack + * Headphone Jack + * Ext Spk + +- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) +- mux-ext-port : The external port of the i.MX audio muxer + +Note: The AUDMUX port numbering should start at 1, which is consistent with +hardware manual. + +Example: + +sound { + compatible = "fsl,imx6q-sabresd-wm8962", + "fsl,imx-audio-wm8962"; + model = "wm8962-audio"; + ssi-controller = <&ssi2>; + audio-codec = <&codec>; + audio-routing = + "Headphone Jack", "HPOUTL", + "Headphone Jack", "HPOUTR", + "Ext Spk", "SPKOUTL", + "Ext Spk", "SPKOUTR", + "MICBIAS", "AMIC", + "IN3R", "MICBIAS", + "DMIC", "MICBIAS", + "DMICDAT", "DMIC"; + mux-int-port = <2>; + mux-ext-port = <3>; +}; diff --git a/Documentation/devicetree/bindings/sound/mxs-saif.txt b/Documentation/devicetree/bindings/sound/mxs-saif.txt index c37ba6143d9b..7ba07a118e37 100644 --- a/Documentation/devicetree/bindings/sound/mxs-saif.txt +++ b/Documentation/devicetree/bindings/sound/mxs-saif.txt @@ -3,8 +3,11 @@ Required properties: - compatible: Should be "fsl,<chip>-saif" - reg: Should contain registers location and length -- interrupts: Should contain ERROR and DMA interrupts -- fsl,saif-dma-channel: APBX DMA channel for the SAIF +- interrupts: Should contain ERROR interrupt number +- dmas: DMA specifier, consisting of a phandle to DMA controller node + and SAIF DMA channel ID. + Refer to dma.txt and fsl-mxs-dma.txt for details. +- dma-names: Must be "rx-tx". Optional properties: - fsl,saif-master: phandle to the master SAIF. It's only required for @@ -23,14 +26,16 @@ aliases { saif0: saif@80042000 { compatible = "fsl,imx28-saif"; reg = <0x80042000 2000>; - interrupts = <59 80>; - fsl,saif-dma-channel = <4>; + interrupts = <59>; + dmas = <&dma_apbx 4>; + dma-names = "rx-tx"; }; saif1: saif@80046000 { compatible = "fsl,imx28-saif"; reg = <0x80046000 2000>; - interrupts = <58 81>; - fsl,saif-dma-channel = <5>; + interrupts = <58>; + dmas = <&dma_apbx 5>; + dma-names = "rx-tx"; fsl,saif-master = <&saif0>; }; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt new file mode 100644 index 000000000000..d130818700b2 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt @@ -0,0 +1,71 @@ +NVIDIA Tegra audio complex, with RT5640 CODEC + +Required properties: +- compatible : "nvidia,tegra-audio-rt5640" +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Must include the following entries: + "pll_a" (The Tegra clock of that name), + "pll_a_out0" (The Tegra clock of that name), + "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) +- nvidia,model : The user-visible name of this sound complex. +- nvidia,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the RT5640's pins, and the jacks on the board: + + RT5640 pins: + + * DMIC1 + * DMIC2 + * MICBIAS1 + * IN1P + * IN1R + * IN2P + * IN2R + * HPOL + * HPOR + * LOUTL + * LOUTR + * MONOP + * MONON + * SPOLP + * SPOLN + * SPORP + * SPORN + + Board connectors: + + * Headphones + * Speakers + +- nvidia,i2s-controller : The phandle of the Tegra I2S controller that's + connected to the CODEC. +- nvidia,audio-codec : The phandle of the RT5640 audio codec. This binding + assumes that AIF1 on the CODEC is connected to Tegra. + +Optional properties: +- nvidia,hp-det-gpios : The GPIO that detects headphones are plugged in + +Example: + +sound { + compatible = "nvidia,tegra-audio-rt5640-dalmore", + "nvidia,tegra-audio-rt5640"; + nvidia,model = "NVIDIA Tegra Dalmore"; + + nvidia,audio-routing = + "Headphones", "HPOR", + "Headphones", "HPOL", + "Speakers", "SPORP", + "Speakers", "SPORN", + "Speakers", "SPOLP", + "Speakers", "SPOLN"; + + nvidia,i2s-controller = <&tegra_i2s1>; + nvidia,audio-codec = <&rt5640>; + + nvidia,hp-det-gpios = <&gpio 143 0>; /* GPIO PR7 */ + + clocks = <&tegra_car 216>, <&tegra_car 217>, <&tegra_car 120>; + clock-names = "pll_a", "pll_a_out0", "mclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5640.txt b/Documentation/devicetree/bindings/sound/rt5640.txt new file mode 100644 index 000000000000..005bcb24d72d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5640.txt @@ -0,0 +1,30 @@ +RT5640 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5640". + +- reg : The I2C address of the device. + +- interrupts : The CODEC's interrupt output. + +Optional properties: + +- realtek,in1-differential +- realtek,in2-differential + Boolean. Indicate MIC1/2 input are differential, rather than single-ended. + +- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. + +Example: + +rt5640 { + compatible = "realtek,rt5640"; + reg = <0x1c>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>; + realtek,ldo1-en-gpios = + <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 9cc44449508d..955df60a118c 100644 --- a/Documentation/devicetree/bindings/sound/sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -5,9 +5,12 @@ Required properties: - reg : the I2C address of the device +- clocks : the clock provider of SYS_MCLK + Example: codec: sgtl5000@0a { compatible = "fsl,sgtl5000"; reg = <0x0a>; + clocks = <&clks 150>; }; diff --git a/Documentation/devicetree/bindings/sound/spdif-receiver.txt b/Documentation/devicetree/bindings/sound/spdif-receiver.txt new file mode 100644 index 000000000000..80f807bf8a1d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/spdif-receiver.txt @@ -0,0 +1,10 @@ +Device-Tree bindings for dummy spdif receiver + +Required properties: + - compatible: should be "linux,spdif-dir". + +Example node: + + codec: spdif-receiver { + compatible = "linux,spdif-dir"; + }; diff --git a/Documentation/devicetree/bindings/sound/spdif-transmitter.txt b/Documentation/devicetree/bindings/sound/spdif-transmitter.txt new file mode 100644 index 000000000000..55a85841dd85 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/spdif-transmitter.txt @@ -0,0 +1,10 @@ +Device-Tree bindings for dummy spdif transmitter + +Required properties: + - compatible: should be "linux,spdif-dit". + +Example node: + + codec: spdif-transmitter { + compatible = "linux,spdif-dit"; + }; diff --git a/Documentation/devicetree/bindings/sound/ssm2518.txt b/Documentation/devicetree/bindings/sound/ssm2518.txt new file mode 100644 index 000000000000..59381a778c79 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ssm2518.txt @@ -0,0 +1,20 @@ +SSM2518 audio amplifier + +This device supports I2C only. + +Required properties: + - compatible : Must be "adi,ssm2518" + - reg : the I2C address of the device. This will either be 0x34 (ADDR pin low) + or 0x35 (ADDR pin high) + +Optional properties: + - gpios : GPIO connected to the nSD pin. If the property is not present it is + assumed that the nSD pin is hardwired to always on. + +Example: + + ssm2518: ssm2518@34 { + compatible = "adi,ssm2518"; + reg = <0x34>; + gpios = <&gpio 5 0>; + }; diff --git a/Documentation/devicetree/bindings/sound/ti,tas5086.txt b/Documentation/devicetree/bindings/sound/ti,tas5086.txt index 8ea4f5b4818d..d2866a0d6a26 100644 --- a/Documentation/devicetree/bindings/sound/ti,tas5086.txt +++ b/Documentation/devicetree/bindings/sound/ti,tas5086.txt @@ -20,6 +20,17 @@ Optional properties: When not specified, the hardware default of 1300ms is retained. + - ti,mid-z-channel-X: Boolean properties, X being a number from 1 to 6. + If given, channel X will start with the Mid-Z start + sequence, otherwise the default Low-Z scheme is used. + + The correct configuration depends on how the power + stages connected to the PWM output pins work. Not all + power stages are compatible to Mid-Z - please refer + to the datasheets for more details. + + Most systems should not set any of these properties. + Examples: i2c_bus { diff --git a/Documentation/devicetree/bindings/sound/wm8962.txt b/Documentation/devicetree/bindings/sound/wm8962.txt index dceb3b1c2bb7..7f82b59ec8f9 100644 --- a/Documentation/devicetree/bindings/sound/wm8962.txt +++ b/Documentation/devicetree/bindings/sound/wm8962.txt @@ -8,9 +8,32 @@ Required properties: - reg : the I2C address of the device. +Optional properties: + - spk-mono: This is a boolean property. If present, the SPK_MONO bit + of R51 (Class D Control 2) gets set, indicating that the speaker is + in mono mode. + + - mic-cfg : Default register value for R48 (Additional Control 4). + If absent, the default should be the register default. + + - gpio-cfg : A list of GPIO configuration register values. The list must + be 6 entries long. If absent, no configuration of these registers is + performed. And note that only the value within [0x0, 0xffff] is valid. + Any other value is regarded as setting the GPIO register by its reset + value 0x0. + Example: codec: wm8962@1a { compatible = "wlf,wm8962"; reg = <0x1a>; + + gpio-cfg = < + 0x0000 /* 0:Default */ + 0x0000 /* 1:Default */ + 0x0013 /* 2:FN_DMICCLK */ + 0x0000 /* 3:Default */ + 0x8014 /* 4:FN_DMICCDAT */ + 0x0000 /* 5:Default */ + >; }; diff --git a/Documentation/devicetree/bindings/spi/omap-spi.txt b/Documentation/devicetree/bindings/spi/omap-spi.txt index 938809c6829b..4c85c4c69584 100644 --- a/Documentation/devicetree/bindings/spi/omap-spi.txt +++ b/Documentation/devicetree/bindings/spi/omap-spi.txt @@ -10,7 +10,18 @@ Required properties: input. The default is D0 as input and D1 as output. -Example: +Optional properties: +- dmas: List of DMA specifiers with the controller specific format + as described in the generic DMA client binding. A tx and rx + specifier is required for each chip select. +- dma-names: List of DMA request names. These strings correspond + 1:1 with the DMA specifiers listed in dmas. The string naming + is to be "rxN" and "txN" for RX and TX requests, + respectively, where N equals the chip select number. + +Examples: + +[hwmod populated DMA resources] mcspi1: mcspi@1 { #address-cells = <1>; @@ -20,3 +31,17 @@ mcspi1: mcspi@1 { ti,spi-num-cs = <4>; }; +[generic DMA request binding] + +mcspi1: mcspi@1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,omap4-mcspi"; + ti,hwmods = "mcspi1"; + ti,spi-num-cs = <2>; + dmas = <&edma 42 + &edma 43 + &edma 44 + &edma 45>; + dma-names = "tx0", "rx0", "tx1", "rx1"; +}; |
