diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
4 files changed, 213 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/thermal/max77620_thermal.txt b/Documentation/devicetree/bindings/thermal/max77620_thermal.txt new file mode 100644 index 000000000000..323a3b3822aa --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/max77620_thermal.txt @@ -0,0 +1,70 @@ +Thermal driver for MAX77620 Power management IC from Maxim Semiconductor. + +Maxim Semiconductor MAX77620 supports alarm interrupts when its +die temperature crosses 120C and 140C. These threshold temperatures +are not configurable. Device does not provide the real temperature +of die other than just indicating whether temperature is above or +below threshold level. + +Required properties: +------------------- +#thermal-sensor-cells: Please refer <devicetree/bindings/thermal/thermal.txt> + for more details. + The value must be 0. + +For more details, please refer generic thermal DT binding document +<devicetree/bindings/thermal/thermal.txt>. + +Please refer <devicetree/bindings/mfd/max77620.txt> for mfd DT binding +document for the MAX77620. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> +#include <dt-bindings/thermal/thermal.h> +... + +i2c@7000d000 { + spmic: max77620@3c { + compatible = "maxim,max77620"; + ::::: + #thermal-sensor-cells = <0>; + ::: + }; +}; + +cool_dev: cool-dev { + compatible = "cooling-dev"; + #cooling-cells = <2>; +}; + +thermal-zones { + PMIC-Die { + polling-delay = <0>; + polling-delay-passive = <0>; + thermal-sensors = <&spmic>; + + trips { + pmic_die_warn_temp_thresh: hot-die { + temperature = <120000>; + type = "hot"; + hysteresis = <0>; + }; + + pmic_die_cirt_temp_thresh: cirtical-die { + temperature = <140000>; + type = "critical"; + hysteresis = <0>; + }; + }; + + cooling-maps { + map0 { + trip = <&pmic_die_warn_temp_thresh>; + cooling-device = <&cool_dev THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>; + contribution = <100>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt index 81f9a512bc2a..e2f494d74d8a 100644 --- a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt @@ -8,7 +8,9 @@ apmixedsys register space via AHB bus accesses, so a phandle to the APMIXEDSYS is also needed. Required properties: -- compatible: "mediatek,mt8173-thermal" +- compatible: + - "mediatek,mt8173-thermal" : For MT8173 family of SoCs + - "mediatek,mt2701-thermal" : For MT2701 family of SoCs - reg: Address range of the thermal controller - interrupts: IRQ for the thermal controller - clocks, clock-names: Clocks needed for the thermal controller. required diff --git a/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt b/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt index edebfa0a985e..b6c0ae53d4dc 100644 --- a/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt +++ b/Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt @@ -10,8 +10,14 @@ Required properties : - compatible : For Tegra124, must contain "nvidia,tegra124-soctherm". For Tegra132, must contain "nvidia,tegra132-soctherm". For Tegra210, must contain "nvidia,tegra210-soctherm". -- reg : Should contain 1 entry: +- reg : Should contain at least 2 entries for each entry in reg-names: - SOCTHERM register set + - Tegra CAR register set: Required for Tegra124 and Tegra210. + - CCROC register set: Required for Tegra132. +- reg-names : Should contain at least 2 entries: + - soctherm-reg + - car-reg + - ccroc-reg - interrupts : Defines the interrupt used by SOCTHERM - clocks : Must contain an entry for each entry in clock-names. See ../clocks/clock-bindings.txt for details. @@ -25,17 +31,45 @@ Required properties : - #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description of this property. See <dt-bindings/thermal/tegra124-soctherm.h> for a list of valid values when referring to thermal sensors. +- throttle-cfgs: A sub-node which is a container of configuration for each + hardware throttle events. These events can be set as cooling devices. + * throttle events: Sub-nodes must be named as "light" or "heavy". + Properties: + - nvidia,priority: Each throttles has its own throttle settings, so the + SW need to set priorities for various throttle, the HW arbiter can select + the final throttle settings. + Bigger value indicates higher priority, In general, higher priority + translates to lower target frequency. SW needs to ensure that critical + thermal alarms are given higher priority, and ensure that there is + no race if priority of two vectors is set to the same value. + The range of this value is 1~100. + - nvidia,cpu-throt-percent: This property is for Tegra124 and Tegra210. + It is the throttling depth of pulse skippers, it's the percentage + throttling. + - nvidia,cpu-throt-level: This property is only for Tegra132, it is the + level of pulse skippers, which used to throttle clock frequencies. It + indicates cpu clock throttling depth, and the depth can be programmed. + Must set as following values: + TEGRA_SOCTHERM_THROT_LEVEL_LOW, TEGRA_SOCTHERM_THROT_LEVEL_MED + TEGRA_SOCTHERM_THROT_LEVEL_HIGH, TEGRA_SOCTHERM_THROT_LEVEL_NONE + - #cooling-cells: Should be 1. This cooling device only support on/off state. + See ./thermal.txt for a description of this property. Note: - the "critical" type trip points will be set to SOC_THERM hardware as the shut down temperature. Once the temperature of this thermal zone is higher than it, the system will be shutdown or reset by hardware. +- the "hot" type trip points will be set to SOC_THERM hardware as the throttle +temperature. Once the the temperature of this thermal zone is higher +than it, it will trigger the HW throttle event. Example : soctherm@700e2000 { compatible = "nvidia,tegra124-soctherm"; - reg = <0x0 0x700e2000 0x0 0x1000>; + reg = <0x0 0x700e2000 0x0 0x600 /* SOC_THERM reg_base */ + 0x0 0x60006000 0x0 0x400 /* CAR reg_base */ + reg-names = "soctherm-reg", "car-reg"; interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA124_CLK_TSENSOR>, <&tegra_car TEGRA124_CLK_SOC_THERM>; @@ -44,6 +78,76 @@ Example : reset-names = "soctherm"; #thermal-sensor-cells = <1>; + + throttle-cfgs { + /* + * When the "heavy" cooling device triggered, + * the HW will skip cpu clock's pulse in 85% depth + */ + throttle_heavy: heavy { + nvidia,priority = <100>; + nvidia,cpu-throt-percent = <85>; + + #cooling-cells = <1>; + }; + + /* + * When the "light" cooling device triggered, + * the HW will skip cpu clock's pulse in 50% depth + */ + throttle_light: light { + nvidia,priority = <80>; + nvidia,cpu-throt-percent = <50>; + + #cooling-cells = <1>; + }; + + /* + * If these two devices are triggered in same time, the HW throttle + * arbiter will select the highest priority as the final throttle + * settings to skip cpu pulse. + */ + }; + }; + +Example: referring to Tegra132's "reg", "reg-names" and "throttle-cfgs" : + + soctherm@700e2000 { + compatible = "nvidia,tegra132-soctherm"; + reg = <0x0 0x700e2000 0x0 0x600 /* SOC_THERM reg_base */ + 0x0 0x70040000 0x0 0x200>; /* CCROC reg_base */; + reg-names = "soctherm-reg", "ccroc-reg"; + + throttle-cfgs { + /* + * When the "heavy" cooling device triggered, + * the HW will skip cpu clock's pulse in HIGH level + */ + throttle_heavy: heavy { + nvidia,priority = <100>; + nvidia,cpu-throt-level = <TEGRA_SOCTHERM_THROT_LEVEL_HIGH>; + + #cooling-cells = <1>; + }; + + /* + * When the "light" cooling device triggered, + * the HW will skip cpu clock's pulse in MED level + */ + throttle_light: light { + nvidia,priority = <80>; + nvidia,cpu-throt-level = <TEGRA_SOCTHERM_THROT_LEVEL_MED>; + + #cooling-cells = <1>; + }; + + /* + * If these two devices are triggered in same time, the HW throttle + * arbiter will select the highest priority as the final throttle + * settings to skip cpu pulse. + */ + + }; }; Example: referring to thermal sensors : @@ -62,6 +166,19 @@ Example: referring to thermal sensors : hysteresis = <1000>; type = "critical"; }; + + cpu_throttle_trip: throttle-trip { + temperature = <100000>; + hysteresis = <1000>; + type = "hot"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu_throttle_trip>; + cooling-device = <&throttle_heavy 1 1>; + }; }; }; }; diff --git a/Documentation/devicetree/bindings/thermal/qcom-tsens.txt b/Documentation/devicetree/bindings/thermal/qcom-tsens.txt new file mode 100644 index 000000000000..292ed89d900b --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/qcom-tsens.txt @@ -0,0 +1,21 @@ +* QCOM SoC Temperature Sensor (TSENS) + +Required properties: +- compatible : + - "qcom,msm8916-tsens" : For 8916 Family of SoCs + - "qcom,msm8974-tsens" : For 8974 Family of SoCs + - "qcom,msm8996-tsens" : For 8996 Family of SoCs + +- reg: Address range of the thermal registers +- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description. +- Refer to Documentation/devicetree/bindings/nvmem/nvmem.txt to know how to specify +nvmem cells + +Example: +tsens: thermal-sensor@900000 { + compatible = "qcom,msm8916-tsens"; + reg = <0x4a8000 0x2000>; + nvmem-cells = <&tsens_caldata>, <&tsens_calsel>; + nvmem-cell-names = "caldata", "calsel"; + #thermal-sensor-cells = <1>; + }; |
