diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
489 files changed, 5263 insertions, 1064 deletions
diff --git a/Documentation/devicetree/bindings/arc/hsdk.txt b/Documentation/devicetree/bindings/arc/hsdk.txt new file mode 100644 index 000000000000..be50654bbf61 --- /dev/null +++ b/Documentation/devicetree/bindings/arc/hsdk.txt @@ -0,0 +1,7 @@ +Synopsys DesignWare ARC HS Development Kit Device Tree Bindings +--------------------------------------------------------------------------- + +ARC HSDK Board with quad-core ARC HS38x4 in silicon. + +Required root node properties: + - compatible = "snps,hsdk"; diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index 0fff40a6330d..4e4bc0bae597 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -1,6 +1,18 @@ Amlogic MesonX device tree bindings ------------------------------------------- +Work in progress statement: + +Device tree files and bindings applying to Amlogic SoCs and boards are +considered "unstable". Any Amlogic device tree binding may change at +any time. Be sure to use a device tree binary and a kernel image +generated from the same source tree. + +Please refer to Documentation/devicetree/bindings/ABI.txt for a definition of a +stable binding/ABI. + +--------------------------------------------------------------- + Boards with the Amlogic Meson6 SoC shall have the following properties: Required root node property: compatible: "amlogic,meson6" @@ -61,3 +73,32 @@ Board compatible values (alphabetically, grouped by SoC): - "amlogic,q201" (Meson gxm s912) - "kingnovel,r-box-pro" (Meson gxm S912) - "nexbox,a1" (Meson gxm s912) + +Amlogic Meson Firmware registers Interface +------------------------------------------ + +The Meson SoCs have a register bank with status and data shared with the +secure firmware. + +Required properties: + - compatible: For Meson GX SoCs, must be "amlogic,meson-gx-ao-secure", "syscon" + +Properties should indentify components of this register interface : + +Meson GX SoC Information +------------------------ +A firmware register encodes the SoC type, package and revision information on +the Meson GX SoCs. +If present, the following property should be added : + +Optional properties: + - amlogic,has-chip-id: If present, the interface gives the current SoC version. + +Example +------- + +ao-secure@140 { + compatible = "amlogic,meson-gx-ao-secure", "syscon"; + reg = <0x0 0x140 0x0 0x140>; + amlogic,has-chip-id; +}; diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/arm/arch_timer.txt index e926aea1147d..68301b77e854 100644 --- a/Documentation/devicetree/bindings/arm/arch_timer.txt +++ b/Documentation/devicetree/bindings/arm/arch_timer.txt @@ -108,6 +108,5 @@ Example: frame-number = <1> interrupts = <0 15 0x8>; reg = <0xf0003000 0x1000>; - status = "disabled"; }; }; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt index 9c97de23919a..3e3efa046ac5 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt @@ -42,6 +42,10 @@ Raspberry Pi Zero Required root node properties: compatible = "raspberrypi,model-zero", "brcm,bcm2835"; +Raspberry Pi Zero W +Required root node properties: +compatible = "raspberrypi,model-zero-w", "brcm,bcm2835"; + Generic BCM2835 board Required root node properties: compatible = "brcm,bcm2835"; diff --git a/Documentation/devicetree/bindings/arm/bhf.txt b/Documentation/devicetree/bindings/arm/bhf.txt new file mode 100644 index 000000000000..886b503caf9c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bhf.txt @@ -0,0 +1,6 @@ +Beckhoff Automation Platforms Device Tree Bindings +-------------------------------------------------- + +CX9020 Embedded PC +Required root node properties: + - compatible = "bhf,cx9020", "fsl,imx53"; diff --git a/Documentation/devicetree/bindings/arm/coresight.txt b/Documentation/devicetree/bindings/arm/coresight.txt index fcbae6a5e6c1..15ac8e8dcfdf 100644 --- a/Documentation/devicetree/bindings/arm/coresight.txt +++ b/Documentation/devicetree/bindings/arm/coresight.txt @@ -34,8 +34,8 @@ its hardware characteristcs. - Embedded Trace Macrocell (version 4.x): "arm,coresight-etm4x", "arm,primecell"; - - Qualcomm Configurable Replicator (version 1.x): - "qcom,coresight-replicator1x", "arm,primecell"; + - Coresight programmable Replicator : + "arm,coresight-dynamic-replicator", "arm,primecell"; - System Trace Macrocell: "arm,coresight-stm", "arm,primecell"; [1] diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index a44253cad269..b92f12bd5244 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -200,6 +200,7 @@ described below. "arm,realview-smp" "brcm,bcm11351-cpu-method" "brcm,bcm23550" + "brcm,bcm2836-smp" "brcm,bcm-nsp-smp" "brcm,brahma-b15" "marvell,armada-375-smp" diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-8kp.txt b/Documentation/devicetree/bindings/arm/marvell/armada-8kp.txt new file mode 100644 index 000000000000..f3e9624534c6 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell/armada-8kp.txt @@ -0,0 +1,15 @@ +Marvell Armada 8KPlus Platforms Device Tree Bindings +---------------------------------------------------- + +Boards using a SoC of the Marvell Armada 8KP families must carry +the following root node property: + + - compatible, with one of the following values: + + - "marvell,armada-8080", "marvell,armada-ap810-octa", "marvell,armada-ap810" + when the SoC being used is the Armada 8080 + +Example: + +compatible = "marvell,armada-8080-db", "marvell,armada-8080", + "marvell,armada-ap810-octa", "marvell,armada-ap810" diff --git a/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt b/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt index 171d02cadea4..29cdbae6c5ac 100644 --- a/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt +++ b/Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt @@ -183,7 +183,6 @@ cpm_syscon0: system-controller@440000 { gpio-controller; #gpio-cells = <2>; gpio-ranges = <&cpm_pinctrl 0 0 32>; - status = "disabled"; }; }; diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt index da7bd138e6f2..91d517849483 100644 --- a/Documentation/devicetree/bindings/arm/mediatek.txt +++ b/Documentation/devicetree/bindings/arm/mediatek.txt @@ -1,12 +1,12 @@ -MediaTek mt65xx, mt67xx & mt81xx Platforms Device Tree Bindings +MediaTek SoC based Platforms Device Tree Bindings -Boards with a MediaTek mt65xx/mt67xx/mt81xx SoC shall have the -following property: +Boards with a MediaTek SoC shall have the following property: Required root node property: compatible: Must contain one of "mediatek,mt2701" + "mediatek,mt2712" "mediatek,mt6580" "mediatek,mt6589" "mediatek,mt6592" @@ -14,7 +14,8 @@ compatible: Must contain one of "mediatek,mt6795" "mediatek,mt6797" "mediatek,mt7622" - "mediatek,mt7623" + "mediatek,mt7623" which is referred to MT7623N SoC + "mediatek,mt7623a" "mediatek,mt8127" "mediatek,mt8135" "mediatek,mt8173" @@ -25,6 +26,9 @@ Supported boards: - Evaluation board for MT2701: Required root node properties: - compatible = "mediatek,mt2701-evb", "mediatek,mt2701"; +- Evaluation board for MT2712: + Required root node properties: + - compatible = "mediatek,mt2712-evb", "mediatek,mt2712"; - Evaluation board for MT6580: Required root node properties: - compatible = "mediatek,mt6580-evbp1", "mediatek,mt6580"; @@ -46,9 +50,11 @@ Supported boards: - Reference board variant 1 for MT7622: Required root node properties: - compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622"; -- Evaluation board for MT7623: +- Reference board for MT7623n with NAND: Required root node properties: - - compatible = "mediatek,mt7623-evb", "mediatek,mt7623"; + - compatible = "mediatek,mt7623n-rfb-nand", "mediatek,mt7623"; +- Bananapi BPI-R2 board: + - compatible = "bananapi,bpi-r2", "mediatek,mt7623"; - MTK mt8127 tablet moose EVB: Required root node properties: - compatible = "mediatek,mt8127-moose", "mediatek,mt8127"; diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 8219b2c6bb29..2ecc712bf707 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -80,6 +80,9 @@ SoCs: - OMAP5432 compatible = "ti,omap5432", "ti,omap5" +- DRA762 + compatible = "ti,dra762", "ti,dra7" + - DRA742 compatible = "ti,dra742", "ti,dra74", "ti,dra7" @@ -154,6 +157,9 @@ Boards: - AM335X phyCORE-AM335x: Development kit compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx" +- AM335X UC-8100-ME-T: Communication-centric industrial computing platform + compatible = "moxa,uc-8100-me-t", "ti,am33xx"; + - OMAP5 EVM : Evaluation Module compatible = "ti,omap5-evm", "ti,omap5" @@ -184,6 +190,9 @@ Boards: - AM5718 IDK compatible = "ti,am5718-idk", "ti,am5718", "ti,dra7" +- DRA762 EVM: Software Development Board for DRA762 + compatible = "ti,dra76-evm", "ti,dra762", "ti,dra7" + - DRA742 EVM: Software Development Board for DRA742 compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7" diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt index 61c8b4620415..13611a8199bb 100644 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -9,9 +9,11 @@ Required properties: - compatible : should be one of "apm,potenza-pmu" "arm,armv8-pmuv3" + "arm,cortex-a73-pmu" "arm,cortex-a72-pmu" "arm,cortex-a57-pmu" "arm,cortex-a53-pmu" + "arm,cortex-a35-pmu" "arm,cortex-a17-pmu" "arm,cortex-a15-pmu" "arm,cortex-a12-pmu" diff --git a/Documentation/devicetree/bindings/arm/qcom.txt b/Documentation/devicetree/bindings/arm/qcom.txt index 028d16e72186..0ed4d39d7fe1 100644 --- a/Documentation/devicetree/bindings/arm/qcom.txt +++ b/Documentation/devicetree/bindings/arm/qcom.txt @@ -25,6 +25,7 @@ The 'SoC' element must be one of the following strings: msm8994 msm8996 mdm9615 + ipq8074 The 'board' element must be one of the following strings: @@ -33,6 +34,7 @@ The 'board' element must be one of the following strings: dragonboard mtp sbc + hk01 The 'soc_version' and 'board_version' elements take the form of v<Major>.<Minor> where the minor number may be omitted when it's zero, i.e. v1.0 is the same diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 11c0ac4a2d56..b003148e2945 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -134,6 +134,10 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "phytec,rk3288-pcm-947", "phytec,rk3288-phycore-som", "rockchip,rk3288"; +- Pine64 Rock64 board: + Required root node properties: + - compatible = "pine64,rock64", "rockchip,rk3328"; + - Rockchip PX3 Evaluation board: Required root node properties: - compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188"; @@ -173,6 +177,14 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "rockchip,rk3399-evb", "rockchip,rk3399"; +- Rockchip RK3399 Sapphire Excavator board: + Required root node properties: + - compatible = "rockchip,rk3399-sapphire-excavator", "rockchip,rk3399"; + +- Theobroma Systems RK3399-Q7 Haikou Baseboard: + Required root node properties: + - compatible = "tsd,rk3399-q7-haikou", "rockchip,rk3399"; + - Tronsmart Orion R68 Meta Required root node properties: - compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368"; diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index 1a671e329864..ae75cb3b1331 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -39,6 +39,8 @@ SoCs: compatible = "renesas,r8a7795" - R-Car M3-W (R8A77960) compatible = "renesas,r8a7796" + - R-Car D3 (R8A77995) + compatible = "renesas,r8a77995" Boards: @@ -53,6 +55,8 @@ Boards: compatible = "renesas,blanche", "renesas,r8a7792" - BOCK-W compatible = "renesas,bockw", "renesas,r8a7778" + - Draak (RTP0RC77995SEB0010S) + compatible = "renesas,draak", "renesas,r8a77995" - Genmai (RTK772100BC00000BR) compatible = "renesas,genmai", "renesas,r7s72100" - GR-Peach (X28A-M01-E/F) @@ -64,6 +68,10 @@ Boards: compatible = "renesas,h3ulcb", "renesas,r8a7795"; - Henninger compatible = "renesas,henninger", "renesas,r8a7791" + - iWave Systems RZ/G1E SODIMM SOM Development Platform (iW-RainboW-G22D) + compatible = "iwave,g22d", "iwave,g22m", "renesas,r8a7745" + - iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) + compatible = "iwave,g22m", "renesas,r8a7745" - iWave Systems RZ/G1M Qseven Development Platform (iW-RainboW-G20D-Qseven) compatible = "iwave,g20d", "iwave,g20m", "renesas,r8a7743" - iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven) diff --git a/Documentation/devicetree/bindings/ata/ahci-mtk.txt b/Documentation/devicetree/bindings/ata/ahci-mtk.txt new file mode 100644 index 000000000000..d2aa696b161b --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-mtk.txt @@ -0,0 +1,51 @@ +MediaTek Serial ATA controller + +Required properties: + - compatible : Must be "mediatek,<chip>-ahci", "mediatek,mtk-ahci". + When using "mediatek,mtk-ahci" compatible strings, you + need SoC specific ones in addition, one of: + - "mediatek,mt7622-ahci" + - reg : Physical base addresses and length of register sets. + - interrupts : Interrupt associated with the SATA device. + - interrupt-names : Associated name must be: "hostc". + - clocks : A list of phandle and clock specifier pairs, one for each + entry in clock-names. + - clock-names : Associated names must be: "ahb", "axi", "asic", "rbc", "pm". + - phys : A phandle and PHY specifier pair for the PHY port. + - phy-names : Associated name must be: "sata-phy". + - ports-implemented : See ./ahci-platform.txt for details. + +Optional properties: + - power-domains : A phandle and power domain specifier pair to the power + domain which is responsible for collapsing and restoring + power to the peripheral. + - resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names : Associated names must be: "axi", "sw", "reg". + - mediatek,phy-mode : A phandle to the system controller, used to enable + SATA function. + +Example: + + sata: sata@1a200000 { + compatible = "mediatek,mt7622-ahci", + "mediatek,mtk-ahci"; + reg = <0 0x1a200000 0 0x1100>; + interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hostc"; + clocks = <&pciesys CLK_SATA_AHB_EN>, + <&pciesys CLK_SATA_AXI_EN>, + <&pciesys CLK_SATA_ASIC_EN>, + <&pciesys CLK_SATA_RBC_EN>, + <&pciesys CLK_SATA_PM_EN>; + clock-names = "ahb", "axi", "asic", "rbc", "pm"; + phys = <&u3port1 PHY_TYPE_SATA>; + phy-names = "sata-phy"; + ports-implemented = <0x1>; + power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>; + resets = <&pciesys MT7622_SATA_AXI_BUS_RST>, + <&pciesys MT7622_SATA_PHY_SW_RST>, + <&pciesys MT7622_SATA_PHY_REG_RST>; + reset-names = "axi", "sw", "reg"; + mediatek,phy-mode = <&pciesys>; + }; diff --git a/Documentation/devicetree/bindings/ata/apm-xgene.txt b/Documentation/devicetree/bindings/ata/apm-xgene.txt index a668f0e7d001..02e690a675db 100644 --- a/Documentation/devicetree/bindings/ata/apm-xgene.txt +++ b/Documentation/devicetree/bindings/ata/apm-xgene.txt @@ -57,7 +57,6 @@ Example: <0x0 0x1f227000 0x0 0x1000>; interrupts = <0x0 0x87 0x4>; dma-coherent; - status = "ok"; clocks = <&sataclk 0>; phys = <&phy2 0>; phy-names = "sata-phy"; @@ -72,7 +71,6 @@ Example: <0x0 0x1f237000 0x0 0x1000>; interrupts = <0x0 0x88 0x4>; dma-coherent; - status = "ok"; clocks = <&sataclk 0>; phys = <&phy3 0>; phy-names = "sata-phy"; diff --git a/Documentation/devicetree/bindings/ata/imx-pata.txt b/Documentation/devicetree/bindings/ata/imx-pata.txt index e38d73414b0d..f1172f00188a 100644 --- a/Documentation/devicetree/bindings/ata/imx-pata.txt +++ b/Documentation/devicetree/bindings/ata/imx-pata.txt @@ -13,5 +13,4 @@ Example: reg = <0x83fe0000 0x4000>; interrupts = <70>; clocks = <&clks 161>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/bus/mvebu-mbus.txt b/Documentation/devicetree/bindings/bus/mvebu-mbus.txt index fa6cde41b460..f2ab7fd013bd 100644 --- a/Documentation/devicetree/bindings/bus/mvebu-mbus.txt +++ b/Documentation/devicetree/bindings/bus/mvebu-mbus.txt @@ -227,7 +227,6 @@ See the example below, where a more complete device tree is shown: }; devbus-bootcs { - status = "okay"; ranges = <0 MBUS_ID(0x01, 0x2f) 0 0x8000000>; /* NOR */ @@ -240,7 +239,6 @@ See the example below, where a more complete device tree is shown: pcie-controller { compatible = "marvell,armada-xp-pcie"; - status = "okay"; device_type = "pci"; #address-cells = <3>; @@ -258,7 +256,6 @@ See the example below, where a more complete device tree is shown: pcie@1,0 { /* Port 0, Lane 0 */ - status = "okay"; }; }; diff --git a/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt b/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt index 83b0e54f727c..3e21eb822811 100644 --- a/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt +++ b/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt @@ -84,7 +84,6 @@ gmi@70090000 { reset-names = "gmi"; ranges = <4 0 0xd0000000 0xfffffff>; - status = "okay"; bus@4,0 { compatible = "simple-bus"; @@ -121,7 +120,6 @@ gmi@70090000 { reset-names = "gmi"; ranges = <4 0 0xd0000000 0xfffffff>; - status = "okay"; can@4,0 { reg = <4 0 0x100>; diff --git a/Documentation/devicetree/bindings/bus/nvidia,tegra210-aconnect.txt b/Documentation/devicetree/bindings/bus/nvidia,tegra210-aconnect.txt index 7ff13be1750b..3108d03802ee 100644 --- a/Documentation/devicetree/bindings/bus/nvidia,tegra210-aconnect.txt +++ b/Documentation/devicetree/bindings/bus/nvidia,tegra210-aconnect.txt @@ -33,7 +33,6 @@ Example: #size-cells = <1>; ranges = <0x702c0000 0x0 0x702c0000 0x00040000>; - status = "disabled"; child1 { ... diff --git a/Documentation/devicetree/bindings/chosen.txt b/Documentation/devicetree/bindings/chosen.txt index dee3f5d9df26..e3b13ea7d2ae 100644 --- a/Documentation/devicetree/bindings/chosen.txt +++ b/Documentation/devicetree/bindings/chosen.txt @@ -5,9 +5,31 @@ The chosen node does not represent a real device, but serves as a place for passing data between firmware and the operating system, like boot arguments. Data in the chosen node does not represent the hardware. +The following properties are recognized: -stdout-path property --------------------- + +kaslr-seed +----------- + +This property is used when booting with CONFIG_RANDOMIZE_BASE as the +entropy used to randomize the kernel image base address location. Since +it is used directly, this value is intended only for KASLR, and should +not be used for other purposes (as it may leak information about KASLR +offsets). It is parsed as a u64 value, e.g. + +/ { + chosen { + kaslr-seed = <0xfeedbeef 0xc0def00d>; + }; +}; + +Note that if this property is set from UEFI (or a bootloader in EFI +mode) when EFI_RNG_PROTOCOL is supported, it will be overwritten by +the Linux EFI stub (which will populate the property itself, using +EFI_RNG_PROTOCOL). + +stdout-path +----------- Device trees may specify the device to be used for boot console output with a stdout-path property under /chosen, as described in the Devicetree diff --git a/Documentation/devicetree/bindings/clock/alphascale,acc.txt b/Documentation/devicetree/bindings/clock/alphascale,acc.txt index 62e67e883e76..b3205b21c9d0 100644 --- a/Documentation/devicetree/bindings/clock/alphascale,acc.txt +++ b/Documentation/devicetree/bindings/clock/alphascale,acc.txt @@ -102,7 +102,6 @@ uart4: serial@80010000 { reg = <0x80010000 0x4000>; clocks = <&acc CLKID_SYS_UART4>, <&acc CLKID_AHB_UART4>; interrupts = <19>; - status = "disabled"; }; Clock consumer with only one, _AHB_ sink. diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt index a55d31b48d6e..786dc39ca904 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt @@ -5,9 +5,11 @@ controllers within the Always-On part of the SoC. Required Properties: -- compatible: should be "amlogic,gxbb-aoclkc" -- reg: physical base address of the clock controller and length of memory - mapped region. +- compatible: value should be different for each SoC family as : + - GXBB (S905) : "amlogic,meson-gxbb-aoclkc" + - GXL (S905X, S905D) : "amlogic,meson-gxl-aoclkc" + - GXM (S912) : "amlogic,meson-gxm-aoclkc" + followed by the common "amlogic,meson-gx-aoclkc" - #clock-cells: should be 1. @@ -23,14 +25,22 @@ to specify the reset which they consume. All available resets are defined as preprocessor macros in the dt-bindings/reset/gxbb-aoclkc.h header and can be used in device tree sources. +Parent node should have the following properties : +- compatible: "amlogic,meson-gx-ao-sysctrl", "syscon", "simple-mfd" +- reg: base address and size of the AO system control register space. + Example: AO Clock controller node: - clkc_AO: clock-controller@040 { - compatible = "amlogic,gxbb-aoclkc"; - reg = <0x0 0x040 0x0 0x4>; +ao_sysctrl: sys-ctrl@0 { + compatible = "amlogic,meson-gx-ao-sysctrl", "syscon", "simple-mfd"; + reg = <0x0 0x0 0x0 0x100>; + + clkc_AO: clock-controller { + compatible = "amlogic,meson-gxbb-aoclkc", "amlogic,meson-gx-aoclkc"; #clock-cells = <1>; #reset-cells = <1>; }; +}; Example: UART controller node that consumes the clock and reset generated by the clock controller: @@ -41,5 +51,4 @@ Example: UART controller node that consumes the clock and reset generated interrupts = <0 90 1>; clocks = <&clkc_AO CLKID_AO_UART1>; resets = <&clkc_AO RESET_AO_UART1>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt index a09d627b5508..924040769186 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt @@ -33,5 +33,4 @@ Example: UART controller node that consumes the clock generated by the clock reg = <0xc81004c0 0x14>; interrupts = <0 90 1>; clocks = <&clkc CLKID_CLK81>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt index 606da38c0959..b455c5aa9139 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt @@ -16,18 +16,25 @@ Required Properties: mapped region. - #clock-cells: should be 1. +- #reset-cells: should be 1. Each clock is assigned an identifier and client nodes can use this identifier to specify the clock which they consume. All available clocks are defined as preprocessor macros in the dt-bindings/clock/meson8b-clkc.h header and can be used in device tree sources. +Similarly a preprocessor macro for each reset line is defined in +dt-bindings/reset/amlogic,meson8b-clkc-reset.h (which can be used from the +device tree sources). + + Example: Clock controller node: clkc: clock-controller@c1104000 { - #clock-cells = <1>; compatible = "amlogic,meson8b-clkc"; reg = <0xc1108000 0x4>, <0xc1104000 0x460>; + #clock-cells = <1>; + #reset-cells = <1>; }; @@ -39,5 +46,4 @@ Example: UART controller node that consumes the clock generated by the clock reg = <0xc81004c0 0x14>; interrupts = <0 90 1>; clocks = <&clkc CLKID_CLK81>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index 5f3ad65daf69..51c259a92d02 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -81,6 +81,16 @@ Required properties: "atmel,sama5d2-clk-generated": at91 generated clock + "atmel,sama5d2-clk-audio-pll-frac": + at91 audio fractional pll + + "atmel,sama5d2-clk-audio-pll-pad": + at91 audio pll CLK_AUDIO output pin + + "atmel,sama5d2-clk-audio-pll-pmc" + at91 audio pll output on AUDIOPLLCLK that feeds the PMC + and can be used by peripheral clock or generic clock + Required properties for SCKC node: - reg : defines the IO memory reserved for the SCKC. - #size-cells : shall be 0 (reg is used to encode clk id). diff --git a/Documentation/devicetree/bindings/clock/brcm,kona-ccu.txt b/Documentation/devicetree/bindings/clock/brcm,kona-ccu.txt index 5286e260fcae..8e5a7d868557 100644 --- a/Documentation/devicetree/bindings/clock/brcm,kona-ccu.txt +++ b/Documentation/devicetree/bindings/clock/brcm,kona-ccu.txt @@ -46,7 +46,6 @@ Device tree example: uart@3e002000 { compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart"; - status = "disabled"; reg = <0x3e002000 0x1000>; clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB3>; interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/clock/exynos5433-clock.txt b/Documentation/devicetree/bindings/clock/exynos5433-clock.txt index 1dc80f8811fe..fe885abc9cb4 100644 --- a/Documentation/devicetree/bindings/clock/exynos5433-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5433-clock.txt @@ -465,5 +465,4 @@ Example 3: UART controller node that consumes the clock generated by the clock clock-names = "uart", "clk_uart_baud0"; pinctrl-names = "default"; pinctrl-0 = <&uart0_bus>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/hi3660-clock.txt b/Documentation/devicetree/bindings/clock/hi3660-clock.txt index cc9b86c35758..0035a7ecaf20 100644 --- a/Documentation/devicetree/bindings/clock/hi3660-clock.txt +++ b/Documentation/devicetree/bindings/clock/hi3660-clock.txt @@ -38,5 +38,4 @@ Examples: clocks = <&crg_ctrl HI3660_CLK_MUX_UART0>, <&crg_ctrl HI3660_PCLK>; clock-names = "uartclk", "apb_pclk"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/hix5hd2-clock.txt b/Documentation/devicetree/bindings/clock/hix5hd2-clock.txt index 7894a64887cb..4733e58e491b 100644 --- a/Documentation/devicetree/bindings/clock/hix5hd2-clock.txt +++ b/Documentation/devicetree/bindings/clock/hix5hd2-clock.txt @@ -27,5 +27,4 @@ Examples: interrupts = <0 49 4>; clocks = <&clock HIX5HD2_FIXED_83M>; clock-names = "apb_pclk"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/idt,versaclock5.txt b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt index 53d7e50ed875..05a245c9df08 100644 --- a/Documentation/devicetree/bindings/clock/idt,versaclock5.txt +++ b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt @@ -1,24 +1,32 @@ -Binding for IDT VersaClock5 programmable i2c clock generator. +Binding for IDT VersaClock 5,6 programmable i2c clock generators. -The IDT VersaClock5 are programmable i2c clock generators providing -from 3 to 12 output clocks. +The IDT VersaClock 5 and VersaClock 6 are programmable i2c clock +generators providing from 3 to 12 output clocks. ==I2C device node== Required properties: -- compatible: shall be one of "idt,5p49v5923" , "idt,5p49v5933" , - "idt,5p49v5935". +- compatible: shall be one of + "idt,5p49v5923" + "idt,5p49v5925" + "idt,5p49v5933" + "idt,5p49v5935" + "idt,5p49v6901" - reg: i2c device address, shall be 0x68 or 0x6a. - #clock-cells: from common clock binding; shall be set to 1. - clocks: from common clock binding; list of parent clock handles, - - 5p49v5923: (required) either or both of XTAL or CLKIN + - 5p49v5923 and + 5p49v5925 and + 5p49v6901: (required) either or both of XTAL or CLKIN reference clock. - 5p49v5933 and - 5p49v5935: (optional) property not present (internal Xtal used) or CLKIN reference clock. - clock-names: from common clock binding; clock input names, can be - - 5p49v5923: (required) either or both of "xin", "clkin". + - 5p49v5923 and + 5p49v5925 and + 5p49v6901: (required) either or both of "xin", "clkin". - 5p49v5933 and - 5p49v5935: (optional) property not present or "clkin". @@ -37,6 +45,7 @@ clock specifier, the following mapping applies: 1 -- OUT1 2 -- OUT4 +5P49V5925 and 5P49V5935: 0 -- OUT0_SEL_I2CB 1 -- OUT1 @@ -44,6 +53,13 @@ clock specifier, the following mapping applies: 3 -- OUT3 4 -- OUT4 +5P49V6901: + 0 -- OUT0_SEL_I2CB + 1 -- OUT1 + 2 -- OUT2 + 3 -- OUT3 + 4 -- OUT4 + ==Example== /* 25MHz reference crystal */ diff --git a/Documentation/devicetree/bindings/clock/imx21-clock.txt b/Documentation/devicetree/bindings/clock/imx21-clock.txt index c3b0db437c48..806f63d628bd 100644 --- a/Documentation/devicetree/bindings/clock/imx21-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx21-clock.txt @@ -24,5 +24,4 @@ Examples: clocks = <&clks IMX21_CLK_UART1_IPG_GATE>, <&clks IMX21_CLK_PER1>; clock-names = "ipg", "per"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/imx23-clock.txt b/Documentation/devicetree/bindings/clock/imx23-clock.txt index 5083c0b834b2..8385348d3bd9 100644 --- a/Documentation/devicetree/bindings/clock/imx23-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx23-clock.txt @@ -67,5 +67,4 @@ auart0: serial@8006c000 { reg = <0x8006c000 0x2000>; interrupts = <24 25 23>; clocks = <&clks 32>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/imx25-clock.txt b/Documentation/devicetree/bindings/clock/imx25-clock.txt index ba6b312ff8a5..f8135ea9ca4e 100644 --- a/Documentation/devicetree/bindings/clock/imx25-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx25-clock.txt @@ -157,5 +157,4 @@ uart1: serial@43f90000 { interrupts = <45>; clocks = <&clks 79>, <&clks 50>; clock-names = "ipg", "per"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/imx27-clock.txt b/Documentation/devicetree/bindings/clock/imx27-clock.txt index cc05de9ec393..4c95c048d3b2 100644 --- a/Documentation/devicetree/bindings/clock/imx27-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx27-clock.txt @@ -24,5 +24,4 @@ Examples: clocks = <&clks IMX27_CLK_UART1_IPG_GATE>, <&clks IMX27_CLK_PER1_GATE>; clock-names = "ipg", "per"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/imx28-clock.txt b/Documentation/devicetree/bindings/clock/imx28-clock.txt index e6587af62ff0..d84a37d2885f 100644 --- a/Documentation/devicetree/bindings/clock/imx28-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx28-clock.txt @@ -90,5 +90,4 @@ auart0: serial@8006a000 { reg = <0x8006a000 0x2000>; interrupts = <112 70 71>; clocks = <&clks 45>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/imx31-clock.txt b/Documentation/devicetree/bindings/clock/imx31-clock.txt index 8163d565f697..0a291090e562 100644 --- a/Documentation/devicetree/bindings/clock/imx31-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx31-clock.txt @@ -87,5 +87,4 @@ uart1: serial@43f90000 { interrupts = <45>; clocks = <&clks 10>, <&clks 30>; clock-names = "ipg", "per"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/imx5-clock.txt b/Documentation/devicetree/bindings/clock/imx5-clock.txt index cadc4d29ada6..a24ca9e582d2 100644 --- a/Documentation/devicetree/bindings/clock/imx5-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx5-clock.txt @@ -25,5 +25,4 @@ can1: can@53fc8000 { interrupts = <82>; clocks = <&clks IMX5_CLK_CAN1_IPG_GATE>, <&clks IMX5_CLK_CAN1_SERIAL_GATE>; clock-names = "ipg", "per"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt index 9252912a5b0e..aa0a4d423ef5 100644 --- a/Documentation/devicetree/bindings/clock/imx6q-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -27,5 +27,4 @@ uart1: serial@02020000 { interrupts = <0 26 0x04>; clocks = <&clks IMX6QDL_CLK_UART_IPG>, <&clks IMX6QDL_CLK_UART_SERIAL>; clock-names = "ipg", "per"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/mt8173-cpu-dvfs.txt b/Documentation/devicetree/bindings/clock/mt8173-cpu-dvfs.txt deleted file mode 100644 index 52b457c23eed..000000000000 --- a/Documentation/devicetree/bindings/clock/mt8173-cpu-dvfs.txt +++ /dev/null @@ -1,83 +0,0 @@ -Device Tree Clock bindins for CPU DVFS of Mediatek MT8173 SoC - -Required properties: -- clocks: A list of phandle + clock-specifier pairs for the clocks listed in clock names. -- clock-names: Should contain the following: - "cpu" - The multiplexer for clock input of CPU cluster. - "intermediate" - A parent of "cpu" clock which is used as "intermediate" clock - source (usually MAINPLL) when the original CPU PLL is under - transition and not stable yet. - Please refer to Documentation/devicetree/bindings/clk/clock-bindings.txt for - generic clock consumer properties. -- proc-supply: Regulator for Vproc of CPU cluster. - -Optional properties: -- sram-supply: Regulator for Vsram of CPU cluster. When present, the cpufreq driver - needs to do "voltage tracking" to step by step scale up/down Vproc and - Vsram to fit SoC specific needs. When absent, the voltage scaling - flow is handled by hardware, hence no software "voltage tracking" is - needed. - -Example: --------- - cpu0: cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - reg = <0x000>; - enable-method = "psci"; - cpu-idle-states = <&CPU_SLEEP_0>; - clocks = <&infracfg CLK_INFRA_CA53SEL>, - <&apmixedsys CLK_APMIXED_MAINPLL>; - clock-names = "cpu", "intermediate"; - }; - - cpu1: cpu@1 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - reg = <0x001>; - enable-method = "psci"; - cpu-idle-states = <&CPU_SLEEP_0>; - clocks = <&infracfg CLK_INFRA_CA53SEL>, - <&apmixedsys CLK_APMIXED_MAINPLL>; - clock-names = "cpu", "intermediate"; - }; - - cpu2: cpu@100 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x100>; - enable-method = "psci"; - cpu-idle-states = <&CPU_SLEEP_0>; - clocks = <&infracfg CLK_INFRA_CA57SEL>, - <&apmixedsys CLK_APMIXED_MAINPLL>; - clock-names = "cpu", "intermediate"; - }; - - cpu3: cpu@101 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x101>; - enable-method = "psci"; - cpu-idle-states = <&CPU_SLEEP_0>; - clocks = <&infracfg CLK_INFRA_CA57SEL>, - <&apmixedsys CLK_APMIXED_MAINPLL>; - clock-names = "cpu", "intermediate"; - }; - - &cpu0 { - proc-supply = <&mt6397_vpca15_reg>; - }; - - &cpu1 { - proc-supply = <&mt6397_vpca15_reg>; - }; - - &cpu2 { - proc-supply = <&da9211_vcpu_reg>; - sram-supply = <&mt6397_vsramca7_reg>; - }; - - &cpu3 { - proc-supply = <&da9211_vcpu_reg>; - sram-supply = <&mt6397_vsramca7_reg>; - }; diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt index 63f9d8277d48..dff236f524a7 100644 --- a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt @@ -66,7 +66,6 @@ clock@70110000 { #clock-cells = <0>; clock-output-names = "dfllCPU_out"; vdd-cpu-supply = <&vdd_cpu>; - status = "okay"; nvidia,sample-rate = <12500>; nvidia,droop-ctrl = <0x00000f00>; diff --git a/Documentation/devicetree/bindings/clock/pxa-clock.txt b/Documentation/devicetree/bindings/clock/pxa-clock.txt index 4b4a9024bd99..8f67239411fe 100644 --- a/Documentation/devicetree/bindings/clock/pxa-clock.txt +++ b/Documentation/devicetree/bindings/clock/pxa-clock.txt @@ -12,5 +12,4 @@ Examples: pxa2xx_clks: pxa2xx_clks@41300004 { compatible = "marvell,pxa-clocks"; #clock-cells = <1>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt index 0cd894f987a3..316e13686568 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt @@ -22,6 +22,7 @@ Required Properties: - "renesas,r8a7794-cpg-mssr" for the r8a7794 SoC (R-Car E2) - "renesas,r8a7795-cpg-mssr" for the r8a7795 SoC (R-Car H3) - "renesas,r8a7796-cpg-mssr" for the r8a7796 SoC (R-Car M3-W) + - "renesas,r8a77995-cpg-mssr" for the r8a77995 SoC (R-Car D3) - reg: Base address and length of the memory resource used by the CPG/MSSR block @@ -30,7 +31,7 @@ Required Properties: clock-names - clock-names: List of external parent clock names. Valid names are: - "extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7792, r8a7793, r8a7794, - r8a7795, r8a7796) + r8a7795, r8a7796, r8a77995) - "extalr" (r8a7795, r8a7796) - "usb_extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7793, r8a7794) @@ -81,5 +82,4 @@ Examples dma-names = "tx", "rx"; power-domains = <&cpg>; resets = <&cpg 310>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/renesas,r8a7778-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,r8a7778-cpg-clocks.txt index e4cdaf1cb333..7cc4c0330b53 100644 --- a/Documentation/devicetree/bindings/clock/renesas,r8a7778-cpg-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,r8a7778-cpg-clocks.txt @@ -44,5 +44,4 @@ Examples interrupts = <0 87 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7778_CLK_SDHI0>; power-domains = <&cpg_clocks>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt b/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt new file mode 100644 index 000000000000..e96e085271c1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt @@ -0,0 +1,55 @@ +* Renesas R-Car USB 2.0 clock selector + +This file provides information on what the device node for the R-Car USB 2.0 +clock selector. + +If you connect an external clock to the USB_EXTAL pin only, you should set +the clock rate to "usb_extal" node only. +If you connect an oscillator to both the USB_XTAL and USB_EXTAL, this module +is not needed because this is default setting. (Of course, you can set the +clock rates to both "usb_extal" and "usb_xtal" nodes. + +Case 1: An external clock connects to R-Car SoC + +----------+ +--- R-Car ---------------------+ + |External |---|USB_EXTAL ---> all usb channels| + |clock | |USB_XTAL | + +----------+ +-------------------------------+ +In this case, we need this driver with "usb_extal" clock. + +Case 2: An oscillator connects to R-Car SoC + +----------+ +--- R-Car ---------------------+ + |Oscillator|---|USB_EXTAL -+-> all usb channels| + | |---|USB_XTAL --+ | + +----------+ +-------------------------------+ +In this case, we don't need this selector. + +Required properties: +- compatible: "renesas,r8a7795-rcar-usb2-clock-sel" if the device is a part of + an R8A7795 SoC. + "renesas,r8a7796-rcar-usb2-clock-sel" if the device if a part of + an R8A7796 SoC. + "renesas,rcar-gen3-usb2-clock-sel" for a generic R-Car Gen3 + compatible device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + +- reg: offset and length of the USB 2.0 clock selector register block. +- clocks: A list of phandles and specifier pairs. +- clock-names: Name of the clocks. + - The functional clock must be "ehci_ohci" + - The USB_EXTAL clock pin must be "usb_extal" + - The USB_XTAL clock pin must be "usb_xtal" +- #clock-cells: Must be 0 + +Example (R-Car H3): + + usb2_clksel: clock-controller@e6590630 { + compatible = "renesas,r8a77950-rcar-usb2-clock-sel", + "renesas,rcar-gen3-usb2-clock-sel"; + reg = <0 0xe6590630 0 0x02>; + clocks = <&cpg CPG_MOD 703>, <&usb_extal>, <&usb_xtal>; + clock-names = "ehci_ohci", "usb_extal", "usb_xtal"; + #clock-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt index bb51a33a1fbf..bb5d942075fb 100644 --- a/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt @@ -50,5 +50,4 @@ Examples clocks = <&mstp3_clks R7S72100_CLK_MTU2>; clock-names = "fck"; power-domains = <&cpg_clocks>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3128-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3128-cru.txt index 455a9a00a623..6f8744fd301b 100644 --- a/Documentation/devicetree/bindings/clock/rockchip,rk3128-cru.txt +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3128-cru.txt @@ -1,12 +1,14 @@ -* Rockchip RK3128 Clock and Reset Unit +* Rockchip RK3126/RK3128 Clock and Reset Unit -The RK3128 clock controller generates and supplies clock to various +The RK3126/RK3128 clock controller generates and supplies clock to various controllers within the SoC and also implements a reset controller for SoC peripherals. Required Properties: -- compatible: should be "rockchip,rk3128-cru" +- compatible: should be "rockchip,rk3126-cru" or "rockchip,rk3128-cru" + "rockchip,rk3126-cru" - controller compatible with RK3126 SoC. + "rockchip,rk3128-cru" - controller compatible with RK3128 SoC. - reg: physical base address of the controller and length of memory mapped region. - #clock-cells: should be 1. diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt index 822505e715ae..2632d3f13004 100644 --- a/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt +++ b/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt @@ -46,5 +46,4 @@ Example: UART controller node that consumes the clock generated by the clock interrupts = <1 23 3 4>, <1 23 4 4>; clock-names = "uart", "clk_uart_baud2"; clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt index 2b430960ba47..21a8c23e658f 100644 --- a/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt +++ b/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt @@ -46,5 +46,4 @@ Example: UART controller node that consumes the clock generated by the clock clock-names = "uart", "clk_uart_baud2", "clk_uart_baud3"; clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>, <&clocks SCLK_UART>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt index e67bb05478af..985c0f574e9a 100644 --- a/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt +++ b/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt @@ -52,5 +52,4 @@ Example: UART controller node that consumes the clock generated by the clock "clk_uart_baud3"; clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>, <&clocks SCLK_UART>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c64xx-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c64xx-clock.txt index fa171dc4bd3c..872ee8e0f041 100644 --- a/Documentation/devicetree/bindings/clock/samsung,s3c64xx-clock.txt +++ b/Documentation/devicetree/bindings/clock/samsung,s3c64xx-clock.txt @@ -73,5 +73,4 @@ Example: UART controller node that consumes the clock generated by the clock "clk_uart_baud3"; clocks = <&clock PCLK_UART0>, <&clocks PCLK_UART0>, <&clock SCLK_UART>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt index effd9401c133..15b48e20a061 100644 --- a/Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt +++ b/Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt @@ -74,5 +74,4 @@ Example: UART controller node that consumes the clock generated by the clock "clk_uart_baud1"; clocks = <&clocks UART0>, <&clocks UART0>, <&clocks SCLK_UART0>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/silabs,si5351.txt b/Documentation/devicetree/bindings/clock/silabs,si5351.txt index 28b28309f535..a6c4ef343b44 100644 --- a/Documentation/devicetree/bindings/clock/silabs,si5351.txt +++ b/Documentation/devicetree/bindings/clock/silabs,si5351.txt @@ -12,7 +12,11 @@ generators can be found in [1]. ==I2C device node== Required properties: -- compatible: shall be one of "silabs,si5351{a,a-msop,b,c}". +- compatible: shall be one of the following: + "silabs,si5351a" - Si5351a, QFN20 package + "silabs,si5351a-msop" - Si5351a, MSOP10 package + "silabs,si5351b" - Si5351b, QFN20 package + "silabs,si5351c" - Si5351c, QFN20 package - reg: i2c device address, shall be 0x60 or 0x61. - #clock-cells: from common clock binding; shall be set to 1. - clocks: from common clock binding; list of parent clock diff --git a/Documentation/devicetree/bindings/clock/snps,hsdk-pll-clock.txt b/Documentation/devicetree/bindings/clock/snps,hsdk-pll-clock.txt new file mode 100644 index 000000000000..c56c7553c730 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/snps,hsdk-pll-clock.txt @@ -0,0 +1,28 @@ +Binding for the HSDK Generic PLL clock + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: should be "snps,hsdk-<name>-pll-clock" + "snps,hsdk-core-pll-clock" + "snps,hsdk-gp-pll-clock" + "snps,hsdk-hdmi-pll-clock" +- reg : should contain base register location and length. +- clocks: shall be the input parent clock phandle for the PLL. +- #clock-cells: from common clock binding; Should always be set to 0. + +Example: + input_clk: input-clk { + clock-frequency = <33333333>; + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + + cpu_clk: cpu-clk@0 { + compatible = "snps,hsdk-core-pll-clock"; + reg = <0x00 0x10>; + #clock-cells = <0>; + clocks = <&input_clk>; + }; diff --git a/Documentation/devicetree/bindings/clock/snps,pll-clock.txt b/Documentation/devicetree/bindings/clock/snps,pll-clock.txt new file mode 100644 index 000000000000..11fe4876612c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/snps,pll-clock.txt @@ -0,0 +1,28 @@ +Binding for the AXS10X Generic PLL clock + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: should be "snps,axs10x-<name>-pll-clock" + "snps,axs10x-arc-pll-clock" + "snps,axs10x-pgu-pll-clock" +- reg: should always contain 2 pairs address - length: first for PLL config +registers and second for corresponding LOCK CGU register. +- clocks: shall be the input parent clock phandle for the PLL. +- #clock-cells: from common clock binding; Should always be set to 0. + +Example: + input-clk: input-clk { + clock-frequency = <33333333>; + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + + core-clk: core-clk@80 { + compatible = "snps,axs10x-arc-pll-clock"; + reg = <0x80 0x10>, <0x100 0x10>; + #clock-cells = <0>; + clocks = <&input-clk>; + }; diff --git a/Documentation/devicetree/bindings/clock/st,stm32h7-rcc.txt b/Documentation/devicetree/bindings/clock/st,stm32h7-rcc.txt new file mode 100644 index 000000000000..cac24ee10b72 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st,stm32h7-rcc.txt @@ -0,0 +1,71 @@ +STMicroelectronics STM32H7 Reset and Clock Controller +===================================================== + +The RCC IP is both a reset and a clock controller. + +Please refer to clock-bindings.txt for common clock controller binding usage. +Please also refer to reset.txt for common reset controller binding usage. + +Required properties: +- compatible: Should be: + "st,stm32h743-rcc" + +- reg: should be register base and length as documented in the + datasheet + +- #reset-cells: 1, see below + +- #clock-cells : from common clock binding; shall be set to 1 + +- clocks: External oscillator clock phandle + - high speed external clock signal (HSE) + - low speed external clock signal (LSE) + - external I2S clock (I2S_CKIN) + +Optional properties: +- st,syscfg: phandle for pwrcfg, mandatory to disable/enable backup domain + write protection (RTC clock). + +Example: + + rcc: reset-clock-controller@58024400 { + compatible = "st,stm32h743-rcc", "st,stm32-rcc"; + reg = <0x58024400 0x400>; + #reset-cells = <1>; + #clock-cells = <1>; + clocks = <&clk_hse>, <&clk_lse>, <&clk_i2s_ckin>; + + st,syscfg = <&pwrcfg>; +}; + +The peripheral clock consumer should specify the desired clock by +having the clock ID in its "clocks" phandle cell. + +Example: + + timer5: timer@40000c00 { + compatible = "st,stm32-timer"; + reg = <0x40000c00 0x400>; + interrupts = <50>; + clocks = <&rcc TIM5_CK>; + }; + +Specifying softreset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the reset device node and an index specifying +which channel to use. +The index is the bit number within the RCC registers bank, starting from RCC +base address. +It is calculated as: index = register_offset / 4 * 32 + bit_offset. +Where bit_offset is the bit offset within the register. + +For example, for CRC reset: + crc = AHB4RSTR_offset / 4 * 32 + CRCRST_bit_offset = 0x88 / 4 * 32 + 19 = 1107 + +Example: + + timer2 { + resets = <&rcc STM32H7_APB1L_RESET(TIM2)>; + }; diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt index df9fad58facd..7eda08eb8a1e 100644 --- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt +++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt @@ -3,18 +3,24 @@ Allwinner Clock Control Unit Binding Required properties : - compatible: must contain one of the following compatibles: + - "allwinner,sun4i-a10-ccu" + - "allwinner,sun5i-a10s-ccu" + - "allwinner,sun5i-a13-ccu" - "allwinner,sun6i-a31-ccu" + - "allwinner,sun7i-a20-ccu" - "allwinner,sun8i-a23-ccu" - "allwinner,sun8i-a33-ccu" - "allwinner,sun8i-a83t-ccu" - "allwinner,sun8i-a83t-r-ccu" - "allwinner,sun8i-h3-ccu" - "allwinner,sun8i-h3-r-ccu" ++ - "allwinner,sun8i-r40-ccu" - "allwinner,sun8i-v3s-ccu" - "allwinner,sun9i-a80-ccu" - "allwinner,sun50i-a64-ccu" - "allwinner,sun50i-a64-r-ccu" - "allwinner,sun50i-h5-ccu" + - "nextthing,gr8-ccu" - reg: Must contain the registers base address and length - clocks: phandle to the oscillators feeding the CCU. Two are needed: diff --git a/Documentation/devicetree/bindings/clock/ti,sci-clk.txt b/Documentation/devicetree/bindings/clock/ti,sci-clk.txt index 1e884c40ab50..4e59dc6b1778 100644 --- a/Documentation/devicetree/bindings/clock/ti,sci-clk.txt +++ b/Documentation/devicetree/bindings/clock/ti,sci-clk.txt @@ -14,10 +14,9 @@ Required properties: - compatible: Must be "ti,k2g-sci-clk" - #clock-cells: Shall be 2. In clock consumers, this cell represents the device ID and clock ID - exposed by the PM firmware. The assignments can be found in the header - files <dt-bindings/genpd/<soc>.h> (which covers the device IDs) and - <dt-bindings/clock/<soc>.h> (which covers the clock IDs), where <soc> - is the SoC involved, for example 'k2g'. + exposed by the PM firmware. The list of valid values for the device IDs + and clocks IDs for 66AK2G SoC are documented at + http://processors.wiki.ti.com/index.php/TISCI#66AK2G02_Data Examples: -------- diff --git a/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt b/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt index 585e8c191f50..10f7047755f3 100644 --- a/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt +++ b/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt @@ -81,13 +81,11 @@ atl: atl@4843c000 { <&atl_clkin2_ck>, <&atl_clkin3_ck>; clocks = <&atl_gfclk_mux>; clock-names = "fck"; - status = "disabled"; }; #include <dt-bindings/clk/ti-dra7-atl.h> &atl { - status = "okay"; atl2 { bws = <DRA7_ATL_WS_MCASP2_FSX>; diff --git a/Documentation/devicetree/bindings/clock/uniphier-clock.txt b/Documentation/devicetree/bindings/clock/uniphier-clock.txt index 812163060fa3..7b5f602765fe 100644 --- a/Documentation/devicetree/bindings/clock/uniphier-clock.txt +++ b/Documentation/devicetree/bindings/clock/uniphier-clock.txt @@ -6,7 +6,6 @@ System clock Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-clock" - for sLD3 SoC. "socionext,uniphier-ld4-clock" - for LD4 SoC. "socionext,uniphier-pro4-clock" - for Pro4 SoC. "socionext,uniphier-sld8-clock" - for sLD8 SoC. @@ -14,6 +13,7 @@ Required properties: "socionext,uniphier-pxs2-clock" - for PXs2/LD6b SoC. "socionext,uniphier-ld11-clock" - for LD11 SoC. "socionext,uniphier-ld20-clock" - for LD20 SoC. + "socionext,uniphier-pxs3-clock" - for PXs3 SoC - #clock-cells: should be 1. Example: @@ -48,7 +48,6 @@ Media I/O (MIO) clock, SD clock Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-mio-clock" - for sLD3 SoC. "socionext,uniphier-ld4-mio-clock" - for LD4 SoC. "socionext,uniphier-pro4-mio-clock" - for Pro4 SoC. "socionext,uniphier-sld8-mio-clock" - for sLD8 SoC. @@ -56,6 +55,7 @@ Required properties: "socionext,uniphier-pxs2-sd-clock" - for PXs2/LD6b SoC. "socionext,uniphier-ld11-mio-clock" - for LD11 SoC. "socionext,uniphier-ld20-sd-clock" - for LD20 SoC. + "socionext,uniphier-pxs3-sd-clock" - for PXs3 SoC - #clock-cells: should be 1. Example: @@ -82,11 +82,9 @@ Provided clocks: 8: USB2 ch0 host 9: USB2 ch1 host 10: USB2 ch2 host -11: USB2 ch3 host 12: USB2 ch0 PHY 13: USB2 ch1 PHY 14: USB2 ch2 PHY -15: USB2 ch3 PHY Peripheral clock @@ -94,7 +92,6 @@ Peripheral clock Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-peri-clock" - for sLD3 SoC. "socionext,uniphier-ld4-peri-clock" - for LD4 SoC. "socionext,uniphier-pro4-peri-clock" - for Pro4 SoC. "socionext,uniphier-sld8-peri-clock" - for sLD8 SoC. @@ -102,6 +99,7 @@ Required properties: "socionext,uniphier-pxs2-peri-clock" - for PXs2/LD6b SoC. "socionext,uniphier-ld11-peri-clock" - for LD11 SoC. "socionext,uniphier-ld20-peri-clock" - for LD20 SoC. + "socionext,uniphier-pxs3-peri-clock" - for PXs3 SoC - #clock-cells: should be 1. Example: diff --git a/Documentation/devicetree/bindings/clock/zx296702-clk.txt b/Documentation/devicetree/bindings/clock/zx296702-clk.txt index 750442b65505..e85ecb510d56 100644 --- a/Documentation/devicetree/bindings/clock/zx296702-clk.txt +++ b/Documentation/devicetree/bindings/clock/zx296702-clk.txt @@ -31,5 +31,4 @@ uart0: serial@0x09405000 { reg = <0x09405000 0x1000>; interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; clocks = <&lsp1clk ZX296702_UART0_PCLK>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/zx296718-clk.txt b/Documentation/devicetree/bindings/clock/zx296718-clk.txt index 4ad703808407..3a46bf0b2540 100644 --- a/Documentation/devicetree/bindings/clock/zx296718-clk.txt +++ b/Documentation/devicetree/bindings/clock/zx296718-clk.txt @@ -34,5 +34,4 @@ usbphy0:usb-phy0 { #phy-cells = <0>; clocks = <&topclk USB20_PHY_CLK>; clock-names = "phyclk"; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-mediatek.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-mediatek.txt new file mode 100644 index 000000000000..f6403089edcf --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-mediatek.txt @@ -0,0 +1,247 @@ +Binding for MediaTek's CPUFreq driver +===================================== + +Required properties: +- clocks: A list of phandle + clock-specifier pairs for the clocks listed in clock names. +- clock-names: Should contain the following: + "cpu" - The multiplexer for clock input of CPU cluster. + "intermediate" - A parent of "cpu" clock which is used as "intermediate" clock + source (usually MAINPLL) when the original CPU PLL is under + transition and not stable yet. + Please refer to Documentation/devicetree/bindings/clk/clock-bindings.txt for + generic clock consumer properties. +- operating-points-v2: Please refer to Documentation/devicetree/bindings/opp/opp.txt + for detail. +- proc-supply: Regulator for Vproc of CPU cluster. + +Optional properties: +- sram-supply: Regulator for Vsram of CPU cluster. When present, the cpufreq driver + needs to do "voltage tracking" to step by step scale up/down Vproc and + Vsram to fit SoC specific needs. When absent, the voltage scaling + flow is handled by hardware, hence no software "voltage tracking" is + needed. +- #cooling-cells: +- cooling-min-level: +- cooling-max-level: + Please refer to Documentation/devicetree/bindings/thermal/thermal.txt + for detail. + +Example 1 (MT7623 SoC): + + cpu_opp_table: opp_table { + compatible = "operating-points-v2"; + opp-shared; + + opp-598000000 { + opp-hz = /bits/ 64 <598000000>; + opp-microvolt = <1050000>; + }; + + opp-747500000 { + opp-hz = /bits/ 64 <747500000>; + opp-microvolt = <1050000>; + }; + + opp-1040000000 { + opp-hz = /bits/ 64 <1040000000>; + opp-microvolt = <1150000>; + }; + + opp-1196000000 { + opp-hz = /bits/ 64 <1196000000>; + opp-microvolt = <1200000>; + }; + + opp-1300000000 { + opp-hz = /bits/ 64 <1300000000>; + opp-microvolt = <1300000>; + }; + }; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x0>; + clocks = <&infracfg CLK_INFRA_CPUSEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate"; + operating-points-v2 = <&cpu_opp_table>; + #cooling-cells = <2>; + cooling-min-level = <0>; + cooling-max-level = <7>; + }; + cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x1>; + operating-points-v2 = <&cpu_opp_table>; + }; + cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x2>; + operating-points-v2 = <&cpu_opp_table>; + }; + cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x3>; + operating-points-v2 = <&cpu_opp_table>; + }; + +Example 2 (MT8173 SoC): + cpu_opp_table_a: opp_table_a { + compatible = "operating-points-v2"; + opp-shared; + + opp-507000000 { + opp-hz = /bits/ 64 <507000000>; + opp-microvolt = <859000>; + }; + + opp-702000000 { + opp-hz = /bits/ 64 <702000000>; + opp-microvolt = <908000>; + }; + + opp-1001000000 { + opp-hz = /bits/ 64 <1001000000>; + opp-microvolt = <983000>; + }; + + opp-1105000000 { + opp-hz = /bits/ 64 <1105000000>; + opp-microvolt = <1009000>; + }; + + opp-1183000000 { + opp-hz = /bits/ 64 <1183000000>; + opp-microvolt = <1028000>; + }; + + opp-1404000000 { + opp-hz = /bits/ 64 <1404000000>; + opp-microvolt = <1083000>; + }; + + opp-1508000000 { + opp-hz = /bits/ 64 <1508000000>; + opp-microvolt = <1109000>; + }; + + opp-1573000000 { + opp-hz = /bits/ 64 <1573000000>; + opp-microvolt = <1125000>; + }; + }; + + cpu_opp_table_b: opp_table_b { + compatible = "operating-points-v2"; + opp-shared; + + opp-507000000 { + opp-hz = /bits/ 64 <507000000>; + opp-microvolt = <828000>; + }; + + opp-702000000 { + opp-hz = /bits/ 64 <702000000>; + opp-microvolt = <867000>; + }; + + opp-1001000000 { + opp-hz = /bits/ 64 <1001000000>; + opp-microvolt = <927000>; + }; + + opp-1209000000 { + opp-hz = /bits/ 64 <1209000000>; + opp-microvolt = <968000>; + }; + + opp-1404000000 { + opp-hz = /bits/ 64 <1007000000>; + opp-microvolt = <1028000>; + }; + + opp-1612000000 { + opp-hz = /bits/ 64 <1612000000>; + opp-microvolt = <1049000>; + }; + + opp-1807000000 { + opp-hz = /bits/ 64 <1807000000>; + opp-microvolt = <1089000>; + }; + + opp-1989000000 { + opp-hz = /bits/ 64 <1989000000>; + opp-microvolt = <1125000>; + }; + }; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x000>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SLEEP_0>; + clocks = <&infracfg CLK_INFRA_CA53SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate"; + operating-points-v2 = <&cpu_opp_table_a>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x001>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SLEEP_0>; + clocks = <&infracfg CLK_INFRA_CA53SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate"; + operating-points-v2 = <&cpu_opp_table_a>; + }; + + cpu2: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x100>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SLEEP_0>; + clocks = <&infracfg CLK_INFRA_CA57SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate"; + operating-points-v2 = <&cpu_opp_table_b>; + }; + + cpu3: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x101>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SLEEP_0>; + clocks = <&infracfg CLK_INFRA_CA57SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate"; + operating-points-v2 = <&cpu_opp_table_b>; + }; + + &cpu0 { + proc-supply = <&mt6397_vpca15_reg>; + }; + + &cpu1 { + proc-supply = <&mt6397_vpca15_reg>; + }; + + &cpu2 { + proc-supply = <&da9211_vcpu_reg>; + sram-supply = <&mt6397_vsramca7_reg>; + }; + + &cpu3 { + proc-supply = <&da9211_vcpu_reg>; + sram-supply = <&mt6397_vsramca7_reg>; + }; diff --git a/Documentation/devicetree/bindings/crypto/artpec6-crypto.txt b/Documentation/devicetree/bindings/crypto/artpec6-crypto.txt new file mode 100644 index 000000000000..d9cca4875bd6 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/artpec6-crypto.txt @@ -0,0 +1,16 @@ +Axis crypto engine with PDMA interface. + +Required properties: +- compatible : Should be one of the following strings: + "axis,artpec6-crypto" for the version in the Axis ARTPEC-6 SoC + "axis,artpec7-crypto" for the version in the Axis ARTPEC-7 SoC. +- reg: Base address and size for the PDMA register area. +- interrupts: Interrupt handle for the PDMA interrupt line. + +Example: + +crypto@f4264000 { + compatible = "axis,artpec6-crypto"; + reg = <0xf4264000 0x1000>; + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/crypto/atmel-crypto.txt b/Documentation/devicetree/bindings/crypto/atmel-crypto.txt index f2aab3dc2b52..7de1a9674c70 100644 --- a/Documentation/devicetree/bindings/crypto/atmel-crypto.txt +++ b/Documentation/devicetree/bindings/crypto/atmel-crypto.txt @@ -66,3 +66,16 @@ sha@f8034000 { dmas = <&dma1 2 17>; dma-names = "tx"; }; + +* Eliptic Curve Cryptography (I2C) + +Required properties: +- compatible : must be "atmel,atecc508a". +- reg: I2C bus address of the device. +- clock-frequency: must be present in the i2c controller node. + +Example: +atecc508a@C0 { + compatible = "atmel,atecc508a"; + reg = <0xC0>; +}; diff --git a/Documentation/devicetree/bindings/crypto/fsl-dcp.txt b/Documentation/devicetree/bindings/crypto/fsl-dcp.txt index 6949e50f1f16..76a0b4e80e83 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-dcp.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-dcp.txt @@ -13,5 +13,4 @@ dcp@80028000 { compatible = "fsl,imx28-dcp", "fsl,imx23-dcp"; reg = <0x80028000 0x2000>; interrupts = <52 53>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/crypto/inside-secure-safexcel.txt b/Documentation/devicetree/bindings/crypto/inside-secure-safexcel.txt index 941bb6a6fb13..fbc07d12322f 100644 --- a/Documentation/devicetree/bindings/crypto/inside-secure-safexcel.txt +++ b/Documentation/devicetree/bindings/crypto/inside-secure-safexcel.txt @@ -23,5 +23,4 @@ Example: interrupt-names = "mem", "ring0", "ring1", "ring2", "ring3", "eip"; clocks = <&cpm_syscon0 1 26>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/crypto/marvell-cesa.txt b/Documentation/devicetree/bindings/crypto/marvell-cesa.txt index c6c6a4a045bd..28d3f2496b89 100644 --- a/Documentation/devicetree/bindings/crypto/marvell-cesa.txt +++ b/Documentation/devicetree/bindings/crypto/marvell-cesa.txt @@ -41,5 +41,4 @@ Examples: clock-names = "cesa0", "cesa1"; marvell,crypto-srams = <&crypto_sram0>, <&crypto_sram1>; marvell,crypto-sram-size = <0x600>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/crypto/mv_cesa.txt b/Documentation/devicetree/bindings/crypto/mv_cesa.txt index c0c35f00335b..d9b92e2f3138 100644 --- a/Documentation/devicetree/bindings/crypto/mv_cesa.txt +++ b/Documentation/devicetree/bindings/crypto/mv_cesa.txt @@ -29,5 +29,4 @@ Examples: interrupts = <22>; marvell,crypto-srams = <&crypto_sram>; marvell,crypto-sram-size = <0x600>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/crypto/rockchip-crypto.txt b/Documentation/devicetree/bindings/crypto/rockchip-crypto.txt index 096df34b11c1..5e2ba385b8c9 100644 --- a/Documentation/devicetree/bindings/crypto/rockchip-crypto.txt +++ b/Documentation/devicetree/bindings/crypto/rockchip-crypto.txt @@ -25,5 +25,4 @@ Examples: clock-names = "aclk", "hclk", "sclk", "apb_pclk"; resets = <&cru SRST_CRYPTO>; reset-names = "crypto-rst"; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/crypto/st,stm32-hash.txt b/Documentation/devicetree/bindings/crypto/st,stm32-hash.txt new file mode 100644 index 000000000000..04fc246f02f7 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/st,stm32-hash.txt @@ -0,0 +1,30 @@ +* STMicroelectronics STM32 HASH + +Required properties: +- compatible: Should contain entries for this and backward compatible + HASH versions: + - "st,stm32f456-hash" for stm32 F456. + - "st,stm32f756-hash" for stm32 F756. +- reg: The address and length of the peripheral registers space +- interrupts: the interrupt specifier for the HASH +- clocks: The input clock of the HASH instance + +Optional properties: +- resets: The input reset of the HASH instance +- dmas: DMA specifiers for the HASH. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: DMA request name. Should be "in" if a dma is present. +- dma-maxburst: Set number of maximum dma burst supported + +Example: + +hash1: hash@50060400 { + compatible = "st,stm32f756-hash"; + reg = <0x50060400 0x400>; + interrupts = <80>; + clocks = <&rcc 0 STM32F7_AHB2_CLOCK(HASH)>; + resets = <&rcc STM32F7_AHB2_RESET(HASH)>; + dmas = <&dma2 7 2 0x400 0x0>; + dma-names = "in"; + dma-maxburst = <0>; +}; diff --git a/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt b/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt index f2233138eba9..001dd63979a9 100644 --- a/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt +++ b/Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt @@ -15,5 +15,4 @@ Example: rockchip,pmu = <&pmugrf>; clocks = <&cru PCLK_DDR_MON>; clock-names = "pclk_ddr_mon"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt index 7a9e8603c150..d6d2833482c9 100644 --- a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt +++ b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt @@ -205,5 +205,4 @@ Example: rockchip,phy_lpddr4_ck_cs_drv = <PHY_DRV_ODT_80>; rockchip,phy_lpddr4_dq_drv = <PHY_DRV_ODT_80>; rockchip,phy_lpddr4_odt = <PHY_DRV_ODT_60>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/display/atmel,lcdc.txt b/Documentation/devicetree/bindings/display/atmel,lcdc.txt index ecb8da063d07..1a21202778ee 100644 --- a/Documentation/devicetree/bindings/display/atmel,lcdc.txt +++ b/Documentation/devicetree/bindings/display/atmel,lcdc.txt @@ -34,7 +34,6 @@ Example: pinctrl-names = "default"; pinctrl-0 = <&pinctrl_fb>; display = <&display0>; - status = "okay"; #address-cells = <1>; #size-cells = <1>; diff --git a/Documentation/devicetree/bindings/display/atmel/hlcdc-dc.txt b/Documentation/devicetree/bindings/display/atmel/hlcdc-dc.txt index ec94468b35be..82f2acb3d374 100644 --- a/Documentation/devicetree/bindings/display/atmel/hlcdc-dc.txt +++ b/Documentation/devicetree/bindings/display/atmel/hlcdc-dc.txt @@ -23,7 +23,6 @@ Example: interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>; clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; clock-names = "periph_clk","sys_clk", "slow_clk"; - status = "disabled"; hlcdc-display-controller { compatible = "atmel,hlcdc-display-controller"; diff --git a/Documentation/devicetree/bindings/display/bridge/megachips-stdpxxxx-ge-b850v3-fw.txt b/Documentation/devicetree/bindings/display/bridge/megachips-stdpxxxx-ge-b850v3-fw.txt index 7baa6582517e..aacc8b92968c 100644 --- a/Documentation/devicetree/bindings/display/bridge/megachips-stdpxxxx-ge-b850v3-fw.txt +++ b/Documentation/devicetree/bindings/display/bridge/megachips-stdpxxxx-ge-b850v3-fw.txt @@ -33,7 +33,6 @@ stdp2690-ge-b850v3-fw required properties: Example: &mux2_i2c2 { - status = "okay"; clock-frequency = <100000>; stdp4028@73 { diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt index 81b68580e199..b1a8929c2536 100644 --- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt +++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt @@ -13,6 +13,7 @@ Required properties: - compatible : Shall contain one or more of - "renesas,r8a7795-hdmi" for R8A7795 (R-Car H3) compatible HDMI TX + - "renesas,r8a7796-hdmi" for R8A7796 (R-Car M3-W) compatible HDMI TX - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 compatible HDMI TX When compatible with generic versions, nodes must list the SoC-specific @@ -43,7 +44,6 @@ Example: clocks = <&cpg CPG_CORE R8A7795_CLK_S0D4>, <&cpg CPG_MOD 729>; clock-names = "iahb", "isfr"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; - status = "disabled"; ports { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt index 549c538b38a5..fc2588292a68 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt @@ -25,12 +25,6 @@ Required properties: size-cells must 1 and 0, respectively. - port: contains an endpoint node which is connected to the endpoint in the mic node. The reg value muset be 0. -- i80-if-timings: specify whether the panel which is connected to decon uses - i80 lcd interface or mipi video interface. This node contains - no timing information as that of fimd does. Because there is - no register in decon to specify i80 interface timing value, - it is not needed, but make it remain to use same kind of node - in fimd and exynos7 decon. Example: SoC specific DT entry: @@ -59,9 +53,3 @@ decon: decon@13800000 { }; }; }; - -Board specific DT entry: -&decon { - i80-if-timings { - }; -}; diff --git a/Documentation/devicetree/bindings/display/fsl,tcon.txt b/Documentation/devicetree/bindings/display/fsl,tcon.txt index 6fa4ab668db5..475008747801 100644 --- a/Documentation/devicetree/bindings/display/fsl,tcon.txt +++ b/Documentation/devicetree/bindings/display/fsl,tcon.txt @@ -14,5 +14,4 @@ timing-controller@4003d000 { reg = <0x4003d000 0x1000>; clocks = <&clks VF610_CLK_TCON0>; clock-names = "ipg"; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt b/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt index fa01db7eb66c..f79854783c2c 100644 --- a/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt +++ b/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt @@ -116,7 +116,7 @@ Parallel display support Required properties: - compatible: Should be "fsl,imx-parallel-display" Optional properties: -- interface_pix_fmt: How this display is connected to the +- interface-pix-fmt: How this display is connected to the display interface. Currently supported types: "rgb24", "rgb565", "bgr666" and "lvds666". - edid: verbatim EDID data block describing attached display. diff --git a/Documentation/devicetree/bindings/display/marvell,pxa2xx-lcdc.txt b/Documentation/devicetree/bindings/display/marvell,pxa2xx-lcdc.txt index 309c47f25b87..f79641bd5f18 100644 --- a/Documentation/devicetree/bindings/display/marvell,pxa2xx-lcdc.txt +++ b/Documentation/devicetree/bindings/display/marvell,pxa2xx-lcdc.txt @@ -23,7 +23,6 @@ Example: reg = <0x44000000 0x10000>; interrupts = <17>; clocks = <&clks CLK_LCD>; - status = "okay"; port { lcdc_out: endpoint { diff --git a/Documentation/devicetree/bindings/display/panel/innolux,p079zca.txt b/Documentation/devicetree/bindings/display/panel/innolux,p079zca.txt index 5c70a8380e58..d0f55161579a 100644 --- a/Documentation/devicetree/bindings/display/panel/innolux,p079zca.txt +++ b/Documentation/devicetree/bindings/display/panel/innolux,p079zca.txt @@ -18,6 +18,5 @@ Example: power-supply = <...>; backlight = <&backlight>; enable-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; - status = "okay"; }; }; diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index c6cb96a4fa93..4bbd1e9bf3be 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -36,8 +36,10 @@ Required Properties: When supplied they must be named "dclkin.x" with "x" being the input clock numerical index. - - vsps: A list of phandles to the VSP nodes that handle the memory - interfaces for the DU channels. + - vsps: A list of phandle and channel index tuples to the VSPs that handle + the memory interfaces for the DU channels. The phandle identifies the VSP + instance that serves the DU channel, and the channel index identifies the + LIF instance in that VSP. Required nodes: @@ -59,24 +61,24 @@ corresponding to each DU output. R8A7796 (M3-W) DPAD HDMI LVDS - -Example: R8A7790 (R-Car H2) DU +Example: R8A7795 (R-Car H3) ES2.0 DU - du: du@feb00000 { - compatible = "renesas,du-r8a7790"; - reg = <0 0xfeb00000 0 0x70000>, - <0 0xfeb90000 0 0x1c>, - <0 0xfeb94000 0 0x1c>; - reg-names = "du", "lvds.0", "lvds.1"; - interrupt-parent = <&gic>; - interrupts = <0 256 IRQ_TYPE_LEVEL_HIGH>, - <0 268 IRQ_TYPE_LEVEL_HIGH>, - <0 269 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp7_clks R8A7790_CLK_DU0>, - <&mstp7_clks R8A7790_CLK_DU1>, - <&mstp7_clks R8A7790_CLK_DU2>, - <&mstp7_clks R8A7790_CLK_LVDS0>, - <&mstp7_clks R8A7790_CLK_LVDS1>; - clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1"; + du: display@feb00000 { + compatible = "renesas,du-r8a7795"; + reg = <0 0xfeb00000 0 0x80000>, + <0 0xfeb90000 0 0x14>; + reg-names = "du", "lvds.0"; + interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 724>, + <&cpg CPG_MOD 723>, + <&cpg CPG_MOD 722>, + <&cpg CPG_MOD 721>, + <&cpg CPG_MOD 727>; + clock-names = "du.0", "du.1", "du.2", "du.3", "lvds.0"; + vsps = <&vspd0 0>, <&vspd1 0>, <&vspd2 0>, <&vspd0 1>; ports { #address-cells = <1>; @@ -89,12 +91,19 @@ Example: R8A7790 (R-Car H2) DU }; port@1 { reg = <1>; - du_out_lvds0: endpoint { + du_out_hdmi0: endpoint { + remote-endpoint = <&dw_hdmi0_in>; }; }; port@2 { reg = <2>; - du_out_lvds1: endpoint { + du_out_hdmi1: endpoint { + remote-endpoint = <&dw_hdmi1_in>; + }; + }; + port@3 { + reg = <3>; + du_out_lvds0: endpoint { }; }; }; diff --git a/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt index 47665a12786f..43561584c13a 100644 --- a/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt +++ b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt @@ -59,7 +59,6 @@ Example: pinctrl-names = "default"; pinctrl-0 = <&edp_hpd>; - status = "disabled"; ports { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt index fad8b7619647..adc94fc3c9f8 100644 --- a/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt +++ b/Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt @@ -46,7 +46,6 @@ hdmi: hdmi@ff980000 { interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_HDCP>; clock-names = "iahb", "isfr"; - status = "disabled"; ports { hdmi_in: port { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt index 543b07435f4f..6bb59ab39f2f 100644 --- a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt +++ b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt @@ -36,7 +36,6 @@ Example: resets = <&cru SRST_MIPIDSI0>; reset-names = "apb"; rockchip,grf = <&grf>; - status = "okay"; ports { #address-cells = <1>; @@ -65,6 +64,5 @@ Example: pinctrl-names = "default"; pinctrl-0 = <&lcd_en>; backlight = <&backlight>; - status = "okay"; }; }; diff --git a/Documentation/devicetree/bindings/display/rockchip/inno_hdmi-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/inno_hdmi-rockchip.txt index 8096a29f9776..cec21714f0e0 100644 --- a/Documentation/devicetree/bindings/display/rockchip/inno_hdmi-rockchip.txt +++ b/Documentation/devicetree/bindings/display/rockchip/inno_hdmi-rockchip.txt @@ -25,7 +25,6 @@ hdmi: hdmi@20034000 { clock-names = "pclk"; pinctrl-names = "default"; pinctrl-0 = <&hdmi_ctl>; - status = "disabled"; hdmi_in: port { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/display/simple-framebuffer-sunxi.txt b/Documentation/devicetree/bindings/display/simple-framebuffer-sunxi.txt index c46ba641a1df..a9168ae6946c 100644 --- a/Documentation/devicetree/bindings/display/simple-framebuffer-sunxi.txt +++ b/Documentation/devicetree/bindings/display/simple-framebuffer-sunxi.txt @@ -28,6 +28,5 @@ chosen { allwinner,pipeline = "de_be0-lcd0-hdmi"; clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>, <&ahb_gates 44>; - status = "disabled"; }; }; diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt index b83e6018041d..92441086caba 100644 --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt @@ -4,15 +4,33 @@ Allwinner A10 Display Pipeline The Allwinner A10 Display pipeline is composed of several components that are going to be documented below: -For the input port of all components up to the TCON in the display -pipeline, if there are multiple components, the local endpoint IDs -must correspond to the index of the upstream block. For example, if -the remote endpoint is Frontend 1, then the local endpoint ID must -be 1. - -Conversely, for the output ports of the same group, the remote endpoint -ID must be the index of the local hardware block. If the local backend -is backend 1, then the remote endpoint ID must be 1. +For all connections between components up to the TCONs in the display +pipeline, when there are multiple components of the same type at the +same depth, the local endpoint ID must be the same as the remote +component's index. For example, if the remote endpoint is Frontend 1, +then the local endpoint ID must be 1. + + Frontend 0 [0] ------- [0] Backend 0 [0] ------- [0] TCON 0 + [1] -- -- [1] [1] -- -- [1] + \ / \ / + X X + / \ / \ + [0] -- -- [0] [0] -- -- [0] + Frontend 1 [1] ------- [1] Backend 1 [1] ------- [1] TCON 1 + +For a two pipeline system such as the one depicted above, the lines +represent the connections between the components, while the numbers +within the square brackets corresponds to the ID of the local endpoint. + +The same rule also applies to DE 2.0 mixer-TCON connections: + + Mixer 0 [0] ----------- [0] TCON 0 + [1] ---- ---- [1] + \ / + X + / \ + [0] ---- ---- [0] + Mixer 1 [1] ----------- [1] TCON 1 HDMI Encoder ------------ @@ -260,7 +278,6 @@ hdmi: hdmi@01c16000 { <&dma SUN4I_DMA_NORMAL 16>, <&dma SUN4I_DMA_DEDICATED 24>; dma-names = "ddc-tx", "ddc-rx", "audio-tx"; - status = "disabled"; ports { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/dma/fsl-edma.txt b/Documentation/devicetree/bindings/dma/fsl-edma.txt index 191d7bd8a6fe..97e213e07660 100644 --- a/Documentation/devicetree/bindings/dma/fsl-edma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-edma.txt @@ -72,5 +72,4 @@ sai2: sai@40031000 { dma-names = "tx", "rx"; dmas = <&edma0 0 21>, <&edma0 0 20>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/dma/mv-xor.txt b/Documentation/devicetree/bindings/dma/mv-xor.txt index c075f5988135..0ffb4d8766a8 100644 --- a/Documentation/devicetree/bindings/dma/mv-xor.txt +++ b/Documentation/devicetree/bindings/dma/mv-xor.txt @@ -30,7 +30,6 @@ xor@d0060900 { reg = <0xd0060900 0x100 0xd0060b00 0x100>; clocks = <&coreclk 0>; - status = "okay"; xor00 { interrupts = <51>; diff --git a/Documentation/devicetree/bindings/dma/qcom_adm.txt b/Documentation/devicetree/bindings/dma/qcom_adm.txt index 9bcab9115982..9d3b2f917b7b 100644 --- a/Documentation/devicetree/bindings/dma/qcom_adm.txt +++ b/Documentation/devicetree/bindings/dma/qcom_adm.txt @@ -48,7 +48,6 @@ Each dmas request consists of 3 cells: Example: spi4: spi@1a280000 { - status = "ok"; spi-max-frequency = <50000000>; pinctrl-0 = <&spi_pins>; diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt index 79a204d50234..891db41e9420 100644 --- a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt @@ -25,6 +25,7 @@ Required Properties: - "renesas,dmac-r8a7794" (R-Car E2) - "renesas,dmac-r8a7795" (R-Car H3) - "renesas,dmac-r8a7796" (R-Car M3-W) + - "renesas,dmac-r8a77970" (R-Car V3M) - reg: base address and length of the registers block for the DMAC diff --git a/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt index e7780a186a36..1be6941ac1e5 100644 --- a/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt @@ -8,6 +8,7 @@ Required Properties: - "renesas,r8a7793-usb-dmac" (R-Car M2-N) - "renesas,r8a7794-usb-dmac" (R-Car E2) - "renesas,r8a7795-usb-dmac" (R-Car H3) + - "renesas,r8a7796-usb-dmac" (R-Car M3-W) - reg: base address and length of the registers block for the DMAC - interrupts: interrupt specifiers for the DMAC, one for each entry in interrupt-names. diff --git a/Documentation/devicetree/bindings/dma/snps-dma.txt b/Documentation/devicetree/bindings/dma/snps-dma.txt index 4775c66f4508..a122723907ac 100644 --- a/Documentation/devicetree/bindings/dma/snps-dma.txt +++ b/Documentation/devicetree/bindings/dma/snps-dma.txt @@ -63,7 +63,6 @@ Example: compatible = "arm,pl011", "arm,primecell"; reg = <0xe0000000 0x1000>; interrupts = <0 35 0x4>; - status = "disabled"; dmas = <&dmahost 12 0 1>, <&dmahost 13 0 1 0>; dma-names = "rx", "rx"; diff --git a/Documentation/devicetree/bindings/dma/st_fdma.txt b/Documentation/devicetree/bindings/dma/st_fdma.txt index 495d853c569b..52cfec9e77ad 100644 --- a/Documentation/devicetree/bindings/dma/st_fdma.txt +++ b/Documentation/devicetree/bindings/dma/st_fdma.txt @@ -69,7 +69,6 @@ Example: sti_uni_player2: sti-uni-player@2 { compatible = "st,sti-uni-player"; - status = "disabled"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; clocks = <&clk_s_d0_flexgen CLK_PCM_2>; diff --git a/Documentation/devicetree/bindings/dma/ste-dma40.txt b/Documentation/devicetree/bindings/dma/ste-dma40.txt index 95800ab37bb0..aa7dbd565ad0 100644 --- a/Documentation/devicetree/bindings/dma/ste-dma40.txt +++ b/Documentation/devicetree/bindings/dma/ste-dma40.txt @@ -135,5 +135,4 @@ Example: <&dma 13 0 0x0>; /* Logical - MemToDev */ dma-names = "rx", "rx"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/dma/sun4i-dma.txt b/Documentation/devicetree/bindings/dma/sun4i-dma.txt index f1634a27a830..3b484380c56a 100644 --- a/Documentation/devicetree/bindings/dma/sun4i-dma.txt +++ b/Documentation/devicetree/bindings/dma/sun4i-dma.txt @@ -40,7 +40,6 @@ Example: clock-names = "ahb", "mod"; dmas = <&dma 1 29>, <&dma 1 28>; dma-names = "rx", "tx"; - status = "disabled"; #address-cells = <1>; #size-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/dma/sun6i-dma.txt b/Documentation/devicetree/bindings/dma/sun6i-dma.txt index 6b267045f522..98fbe1a5c6dd 100644 --- a/Documentation/devicetree/bindings/dma/sun6i-dma.txt +++ b/Documentation/devicetree/bindings/dma/sun6i-dma.txt @@ -9,6 +9,7 @@ Required properties: "allwinner,sun8i-a23-dma" "allwinner,sun8i-a83t-dma" "allwinner,sun8i-h3-dma" + "allwinner,sun8i-v3s-dma" - reg: Should contain the registers base address and length - interrupts: Should contain a reference to the interrupt used by this device - clocks: Should contain a reference to the parent AHB clock diff --git a/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt b/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt index aead5869a28d..b849a1ed389d 100644 --- a/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt +++ b/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt @@ -62,7 +62,6 @@ uart1: serial@4806a000 { interrupts-extended = <&gic GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "uart1"; clock-frequency = <48000000>; - status = "disabled"; /* Requesting crossbar input 49 and 50 */ dmas = <&sdma_xbar 49>, <&sdma_xbar 50>; dma-names = "tx", "rx"; diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt index 18090e7226b4..41f0c1a07c56 100644 --- a/Documentation/devicetree/bindings/dma/ti-edma.txt +++ b/Documentation/devicetree/bindings/dma/ti-edma.txt @@ -9,7 +9,12 @@ execute the actual DMA tansfer. eDMA3 Channel Controller Required properties: -- compatible: "ti,edma3-tpcc" for the channel controller(s) +-------------------- +- compatible: Should be: + - "ti,edma3-tpcc" for the channel controller(s) on OMAP, + AM33xx and AM43xx SoCs. + - "ti,k2g-edma3-tpcc", "ti,edma3-tpcc" for the + channel controller(s) on 66AK2G. - #dma-cells: Should be set to <2>. The first number is the DMA request number and the second is the TC the channel is serviced on. - reg: Memory map of eDMA CC @@ -19,8 +24,19 @@ Required properties: - ti,tptcs: List of TPTCs associated with the eDMA in the following form: <&tptc_phandle TC_priority_number>. The highest priority is 0. +SoC-specific Required properties: +-------------------------------- +The following are mandatory properties for OMAP, AM33xx and AM43xx SoCs only: +- ti,hwmods: Name of the hwmods associated to the eDMA CC. + +The following are mandatory properties for 66AK2G SoCs only: +- power-domains:Should contain a phandle to a PM domain provider node + and an args specifier containing the device id + value. This property is as per the binding, + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt + Optional properties: -- ti,hwmods: Name of the hwmods associated to the eDMA CC +------------------- - ti,edma-memcpy-channels: List of channels allocated to be used for memcpy, iow these channels will be SW triggered channels. See example. - ti,edma-reserved-slot-ranges: PaRAM slot ranges which should not be used by @@ -31,17 +47,34 @@ Optional properties: eDMA3 Transfer Controller Required properties: -- compatible: "ti,edma3-tptc" for the transfer controller(s) +-------------------- +- compatible: Should be: + - "ti,edma3-tptc" for the transfer controller(s) on OMAP, + AM33xx and AM43xx SoCs. + - "ti,k2g-edma3-tptc", "ti,edma3-tptc" for the + transfer controller(s) on 66AK2G. - reg: Memory map of eDMA TC - interrupts: Interrupt number for TCerrint. +SoC-specific Required properties: +-------------------------------- +The following are mandatory properties for OMAP, AM33xx and AM43xx SoCs only: +- ti,hwmods: Name of the hwmods associated to the eDMA TC. + +The following are mandatory properties for 66AK2G SoCs only: +- power-domains:Should contain a phandle to a PM domain provider node + and an args specifier containing the device id + value. This property is as per the binding, + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt + Optional properties: -- ti,hwmods: Name of the hwmods associated to the given eDMA TC +------------------- - interrupt-names: "edma3_tcerrint" ------------------------------------------------------------------------------ -Example: +Examples: +1. edma: edma@49000000 { compatible = "ti,edma3-tpcc"; ti,hwmods = "tpcc"; @@ -102,13 +135,64 @@ mcasp0: mcasp@48038000 { reg-names = "mpu", "dat"; interrupts = <80>, <81>; interrupt-names = "tx", "rx"; - status = "disabled"; /* DMA channels 8 and 9 executed on eDMA TC2 - high priority queue */ dmas = <&edma 8 2>, <&edma 9 2>; dma-names = "tx", "rx"; }; +2. +edma1: edma@02728000 { + compatible = "ti,k2g-edma3-tpcc", "ti,edma3-tpcc"; + reg = <0x02728000 0x8000>; + reg-names = "edma3_cc"; + interrupts = <GIC_SPI 208 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 219 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 220 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "edma3_ccint", "emda3_mperr", + "edma3_ccerrint"; + dma-requests = <64>; + #dma-cells = <2>; + + ti,tptcs = <&edma1_tptc0 7>, <&edma1_tptc1 0>; + + /* + * memcpy is disabled, can be enabled with: + * ti,edma-memcpy-channels = <12 13 14 15>; + * for example. + */ + + power-domains = <&k2g_pds 0x4f>; +}; + +edma1_tptc0: tptc@027b0000 { + compatible = "ti,k2g-edma3-tptc", "ti,edma3-tptc"; + reg = <0x027b0000 0x400>; + power-domains = <&k2g_pds 0x4f>; +}; + +edma1_tptc1: tptc@027b8000 { + compatible = "ti, k2g-edma3-tptc", "ti,edma3-tptc"; + reg = <0x027b8000 0x400>; + power-domains = <&k2g_pds 0x4f>; +}; + +mmc0: mmc@23000000 { + compatible = "ti,k2g-hsmmc", "ti,omap4-hsmmc"; + reg = <0x23000000 0x400>; + interrupts = <GIC_SPI 96 IRQ_TYPE_EDGE_RISING>; + dmas = <&edma1 24 0>, <&edma1 25 0>; + dma-names = "tx", "rx"; + bus-width = <4>; + ti,needs-special-reset; + no-1-8-v; + max-frequency = <96000000>; + power-domains = <&k2g_pds 0xb>; + clocks = <&k2g_clks 0xb 1>, <&k2g_clks 0xb 2>; + clock-names = "fck", "mmchsdb_fck"; + status = "disabled"; +}; + ------------------------------------------------------------------------------ DEPRECATED binding, new DTS files must use the ti,edma3-tpcc/ti,edma3-tptc binding. diff --git a/Documentation/devicetree/bindings/eeprom/eeprom.txt b/Documentation/devicetree/bindings/eeprom/eeprom.txt index 5696eb508e95..afc04589eadf 100644 --- a/Documentation/devicetree/bindings/eeprom/eeprom.txt +++ b/Documentation/devicetree/bindings/eeprom/eeprom.txt @@ -16,8 +16,12 @@ Required properties: "renesas,r1ex24002" + The following manufacturers values have been deprecated: + "at", "at24" + If there is no specific driver for <manufacturer>, a generic - driver based on <type> is selected. Possible types are: + device with <type> and manufacturer "atmel" should be used. + Possible types are: "24c00", "24c01", "24c02", "24c04", "24c08", "24c16", "24c32", "24c64", "24c128", "24c256", "24c512", "24c1024", "spd" diff --git a/Documentation/devicetree/bindings/extcon/extcon-usbc-cros-ec.txt b/Documentation/devicetree/bindings/extcon/extcon-usbc-cros-ec.txt new file mode 100644 index 000000000000..8e8625c00dfa --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-usbc-cros-ec.txt @@ -0,0 +1,24 @@ +ChromeOS EC USB Type-C cable and accessories detection + +On ChromeOS systems with USB Type C ports, the ChromeOS Embedded Controller is +able to detect the state of external accessories such as display adapters +or USB devices when said accessories are attached or detached. + +The node for this device must be under a cros-ec node like google,cros-ec-spi +or google,cros-ec-i2c. + +Required properties: +- compatible: Should be "google,extcon-usbc-cros-ec". +- google,usb-port-id: Specifies the USB port ID to use. + +Example: + cros-ec@0 { + compatible = "google,cros-ec-i2c"; + + ... + + extcon { + compatible = "google,extcon-usbc-cros-ec"; + google,usb-port-id = <0>; + }; + } diff --git a/Documentation/devicetree/bindings/fpga/altera-passive-serial.txt b/Documentation/devicetree/bindings/fpga/altera-passive-serial.txt new file mode 100644 index 000000000000..48478bc07e29 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/altera-passive-serial.txt @@ -0,0 +1,29 @@ +Altera Passive Serial SPI FPGA Manager + +Altera FPGAs support a method of loading the bitstream over what is +referred to as "passive serial". +The passive serial link is not technically SPI, and might require extra +circuits in order to play nicely with other SPI slaves on the same bus. + +See https://www.altera.com/literature/hb/cyc/cyc_c51013.pdf + +Required properties: +- compatible: Must be one of the following: + "altr,fpga-passive-serial", + "altr,fpga-arria10-passive-serial" +- reg: SPI chip select of the FPGA +- nconfig-gpios: config pin (referred to as nCONFIG in the manual) +- nstat-gpios: status pin (referred to as nSTATUS in the manual) + +Optional properties: +- confd-gpios: confd pin (referred to as CONF_DONE in the manual) + +Example: + fpga: fpga@0 { + compatible = "altr,fpga-passive-serial"; + spi-max-frequency = <20000000>; + reg = <0>; + nconfig-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>; + nstat-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; + confd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt new file mode 100644 index 000000000000..8dcfba926bc7 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt @@ -0,0 +1,36 @@ +Xilinx LogiCORE Partial Reconfig Decoupler Softcore + +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more +decouplers / fpga bridges. +The controller can decouple/disable the bridges which prevents signal +changes from passing through the bridge. The controller can also +couple / enable the bridges which allows traffic to pass through the +bridge normally. + +The Driver supports only MMIO handling. A PR region can have multiple +PR Decouplers which can be handled independently or chained via decouple/ +decouple_status signals. + +Required properties: +- compatible : Should contain "xlnx,pr-decoupler-1.00" followed by + "xlnx,pr-decoupler" +- regs : base address and size for decoupler module +- clocks : input clock to IP +- clock-names : should contain "aclk" + +Optional properties: +- bridge-enable : 0 if driver should disable bridge at startup + 1 if driver should enable bridge at startup + Default is to leave bridge in current state. + +See Documentation/devicetree/bindings/fpga/fpga-region.txt for generic bindings. + +Example: + fpga-bridge@100000450 { + compatible = "xlnx,pr-decoupler-1.00", + "xlnx-pr-decoupler"; + regs = <0x10000045 0x10>; + clocks = <&clkc 15>; + clock-names = "aclk"; + bridge-enable = <0>; + }; diff --git a/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt b/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt index 9766f7472f51..cfa4ed42b62f 100644 --- a/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt +++ b/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt @@ -31,7 +31,6 @@ Example for full FPGA configuration: cell-index = <1>; interrupts = <92>; clocks = <&coreclk 0>; - status = "okay"; fpga_mgr_spi: fpga-mgr@0 { compatible = "xlnx,fpga-slave-serial"; diff --git a/Documentation/devicetree/bindings/gpio/gpio-74x164.txt b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt index ce1b2231bf5d..2a97553d8d76 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-74x164.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt @@ -12,6 +12,9 @@ Required properties: 1 = active low - registers-number: Number of daisy-chained shift registers +Optional properties: +- enable-gpios: GPIO connected to the OE (Output Enable) pin. + Example: gpio5: gpio5@0 { diff --git a/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt b/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt index c756afa88cc6..fc6378c778c5 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-aspeed.txt @@ -18,7 +18,7 @@ Required properties: Optional properties: - interrupt-parent : The parent interrupt controller, optional if inherited -- clocks : A phandle to the HPLL clock node for debounce timings +- clocks : A phandle to the clock to use for debounce timings The gpio and interrupt properties are further described in their respective bindings documentation: diff --git a/Documentation/devicetree/bindings/gpio/gpio-davinci.txt b/Documentation/devicetree/bindings/gpio/gpio-davinci.txt index 5079ba7d6568..8beb0539b6d8 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-davinci.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-davinci.txt @@ -1,7 +1,10 @@ Davinci/Keystone GPIO controller bindings Required Properties: -- compatible: should be "ti,dm6441-gpio", "ti,keystone-gpio" +- compatible: should be "ti,dm6441-gpio": for Davinci da850 SoCs + "ti,keystone-gpio": for Keystone 2 66AK2H/K, 66AK2L, + 66AK2E SoCs + "ti,k2g-gpio", "ti,keystone-gpio": for 66AK2G - reg: Physical base address of the controller and the size of memory mapped registers. @@ -20,7 +23,21 @@ Required Properties: - ti,ngpio: The number of GPIO pins supported. - ti,davinci-gpio-unbanked: The number of GPIOs that have an individual interrupt - line to processor. + line to processor. + +- clocks: Should contain the device's input clock, and should be defined as per + the appropriate clock bindings consumer usage in, + + Documentation/devicetree/bindings/clock/keystone-gate.txt + for 66AK2HK/66AK2L/66AK2E SoCs or, + + Documentation/devicetree/bindings/clock/ti,sci-clk.txt + for 66AK2G SoCs + +- clock-names: Name should be "gpio"; + +Currently clock-names and clocks are needed for all keystone 2 platforms +Davinci platforms do not have DT clocks as of now. The GPIO controller also acts as an interrupt controller. It uses the default two cells specifier as described in Documentation/devicetree/bindings/ @@ -60,3 +77,73 @@ leds { ... }; }; + +Example for 66AK2G: + +gpio0: gpio@2603000 { + compatible = "ti,k2g-gpio", "ti,keystone-gpio"; + reg = <0x02603000 0x100>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <GIC_SPI 432 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 433 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 434 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 435 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 436 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 437 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 438 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 439 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 440 IRQ_TYPE_EDGE_RISING>; + interrupt-controller; + #interrupt-cells = <2>; + ti,ngpio = <144>; + ti,davinci-gpio-unbanked = <0>; + clocks = <&k2g_clks 0x001b 0x0>; + clock-names = "gpio"; +}; + +Example for 66AK2HK/66AK2L/66AK2E: + +gpio0: gpio@260bf00 { + compatible = "ti,keystone-gpio"; + reg = <0x0260bf00 0x100>; + gpio-controller; + #gpio-cells = <2>; + /* HW Interrupts mapped to GPIO pins */ + interrupts = <GIC_SPI 120 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 121 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 122 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 123 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 124 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 125 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 126 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 127 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 128 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 129 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 130 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 131 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 132 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 133 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 134 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 135 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 136 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 137 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 138 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 139 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 140 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 141 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 145 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 146 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 147 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 148 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 149 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 150 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 151 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkgpio>; + clock-names = "gpio"; + ti,ngpio = <32>; + ti,davinci-gpio-unbanked = <32>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt index 4b6cc632ca5c..69d46162d0f5 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt @@ -23,7 +23,6 @@ gpio0: gpio@1100 { #gpio-cells = <2>; reg = <0x1100 0x080>; interrupts = <78 0x8>; - status = "okay"; }; Example of gpio-controller node for a ls2080a SoC: diff --git a/Documentation/devicetree/bindings/gpio/gpio-vf610.txt b/Documentation/devicetree/bindings/gpio/gpio-vf610.txt index 436cc99c6598..0ccbae44019c 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-vf610.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-vf610.txt @@ -5,7 +5,9 @@ functionality. Each pair serves 32 GPIOs. The VF610 has 5 instances of each, and each PORT module has its own interrupt. Required properties for GPIO node: -- compatible : Should be "fsl,<soc>-gpio", currently "fsl,vf610-gpio" +- compatible : Should be "fsl,<soc>-gpio", below is supported list: + "fsl,vf610-gpio" + "fsl,imx7ulp-gpio" - reg : The first reg tuple represents the PORT module, the second tuple the GPIO module. - interrupts : Should be the port interrupt shared by all 32 pins. diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index 6826a371fb69..51c86f69995e 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -2,8 +2,9 @@ Required Properties: - - compatible: should contain one of the following. + - compatible: should contain one or more of the following: - "renesas,gpio-r8a7743": for R8A7743 (RZ/G1M) compatible GPIO controller. + - "renesas,gpio-r8a7745": for R8A7745 (RZ/G1E) compatible GPIO controller. - "renesas,gpio-r8a7778": for R8A7778 (R-Mobile M1) compatible GPIO controller. - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller. - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller. @@ -13,7 +14,14 @@ Required Properties: - "renesas,gpio-r8a7794": for R8A7794 (R-Car E2) compatible GPIO controller. - "renesas,gpio-r8a7795": for R8A7795 (R-Car H3) compatible GPIO controller. - "renesas,gpio-r8a7796": for R8A7796 (R-Car M3-W) compatible GPIO controller. - - "renesas,gpio-rcar": for generic R-Car GPIO controller. + - "renesas,rcar-gen1-gpio": for a generic R-Car Gen1 GPIO controller. + - "renesas,rcar-gen2-gpio": for a generic R-Car Gen2 or RZ/G1 GPIO controller. + - "renesas,rcar-gen3-gpio": for a generic R-Car Gen3 GPIO controller. + - "renesas,gpio-rcar": deprecated. + + When compatible with the generic version nodes must list the + SoC-specific version corresponding to the platform first followed by + the generic version. - reg: Base address and length of each memory resource used by the GPIO controller hardware module. @@ -43,7 +51,7 @@ interrupt-controller/interrupts.txt. Example: R8A7779 (R-Car H1) GPIO controller nodes gpio0: gpio@ffc40000 { - compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar"; + compatible = "renesas,gpio-r8a7779", "renesas,rcar-gen1-gpio"; reg = <0xffc40000 0x2c>; interrupt-parent = <&gic>; interrupts = <0 141 0x4>; @@ -55,7 +63,7 @@ Example: R8A7779 (R-Car H1) GPIO controller nodes }; ... gpio6: gpio@ffc46000 { - compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar"; + compatible = "renesas,gpio-r8a7779", "renesas,rcar-gen1-gpio"; reg = <0xffc46000 0x2c>; interrupt-parent = <&gic>; interrupts = <0 147 0x4>; diff --git a/Documentation/devicetree/bindings/gpio/spear_spics.txt b/Documentation/devicetree/bindings/gpio/spear_spics.txt index 96c37eb15075..dd04d96e6ff1 100644 --- a/Documentation/devicetree/bindings/gpio/spear_spics.txt +++ b/Documentation/devicetree/bindings/gpio/spear_spics.txt @@ -42,7 +42,6 @@ spics: spics@e0700000{ spi0: spi@e0100000 { - status = "okay"; num-cs = <3>; cs-gpios = <&gpio1 7 0>, <&spics 0>, <&spics 1>; diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt index 5aa5926029ee..039219df05c5 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt +++ b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt @@ -17,6 +17,7 @@ Required properties: * which must be preceded by one of the following vendor specifics: + "amlogic,meson-gxm-mali" + "rockchip,rk3288-mali" + + "rockchip,rk3399-mali" - reg : Physical base address of the device and length of the register area. diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt index 2b6243e730f6..b4ebd56d03f3 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt +++ b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt @@ -10,6 +10,7 @@ Required properties: * And, optionally, one of the vendor specific compatible: + allwinner,sun4i-a10-mali + allwinner,sun7i-a20-mali + + allwinner,sun50i-h5-mali + amlogic,meson-gxbb-mali + amlogic,meson-gxl-mali + stericsson,db8500-mali @@ -58,6 +59,10 @@ to specify one more vendor-specific compatible, among: Required properties: * resets: phandle to the reset line for the GPU + - allwinner,sun50i-h5-mali + Required properties: + * resets: phandle to the reset line for the GPU + - stericsson,db8500-mali Required properties: * interrupt-names and interrupts: diff --git a/Documentation/devicetree/bindings/gpu/nvidia,gk20a.txt b/Documentation/devicetree/bindings/gpu/nvidia,gk20a.txt index b7e4c7444510..f32bbba4d3bc 100644 --- a/Documentation/devicetree/bindings/gpu/nvidia,gk20a.txt +++ b/Documentation/devicetree/bindings/gpu/nvidia,gk20a.txt @@ -51,7 +51,6 @@ Example for GK20A: resets = <&tegra_car 184>; reset-names = "gpu"; iommus = <&mc TEGRA_SWGROUP_GPU>; - status = "disabled"; }; Example for GM20B: @@ -70,7 +69,6 @@ Example for GM20B: resets = <&tegra_car 184>; reset-names = "gpu"; iommus = <&mc TEGRA_SWGROUP_GPU>; - status = "disabled"; }; Example for GP10B: @@ -89,5 +87,4 @@ Example for GP10B: reset-names = "gpu"; power-domains = <&bpmp TEGRA186_POWER_DOMAIN_GPU>; iommus = <&smmu TEGRA186_SID_GPU>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/gpu/samsung-g2d.txt b/Documentation/devicetree/bindings/gpu/samsung-g2d.txt index c4f358dafdaa..1e7959332dbc 100644 --- a/Documentation/devicetree/bindings/gpu/samsung-g2d.txt +++ b/Documentation/devicetree/bindings/gpu/samsung-g2d.txt @@ -24,5 +24,4 @@ Example: interrupts = <0 89 0>; clocks = <&clock 177>, <&clock 277>; clock-names = "sclk_fimg2d", "fimg2d"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/hsi/omap-ssi.txt b/Documentation/devicetree/bindings/hsi/omap-ssi.txt index f26625e42693..b8eca3c7810d 100644 --- a/Documentation/devicetree/bindings/hsi/omap-ssi.txt +++ b/Documentation/devicetree/bindings/hsi/omap-ssi.txt @@ -92,6 +92,5 @@ ssi-controller@48058000 { interrupts = <69>, <70>; - status = "disabled"; /* second port is not used on N900 */ } } diff --git a/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt b/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt index cf4460564adb..367c8203213b 100644 --- a/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt +++ b/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt @@ -11,6 +11,8 @@ Required properties for pwm-tacho node: - #size-cells : should be 1. +- #cooling-cells: should be 2. + - reg : address and length of the register set for the device. - pinctrl-names : a pinctrl state named "default" must be defined. @@ -28,12 +30,17 @@ fan subnode format: Under fan subnode there can upto 8 child nodes, with each child node representing a fan. If there are 8 fans each fan can have one PWM port and one/two Fan tach inputs. +For PWM port can be configured cooling-levels to create cooling device. +Cooling device could be bound to a thermal zone for the thermal control. Required properties for each child node: - reg : should specify PWM source port. integer value in the range 0 to 7 with 0 indicating PWM port A and 7 indicating PWM port H. +- cooling-levels: PWM duty cycle values in a range from 0 to 255 + which correspond to thermal cooling states. + - aspeed,fan-tach-ch : should specify the Fan tach input channel. integer value in the range 0 through 15, with 0 indicating Fan tach channel 0 and 15 indicating Fan tach channel 15. @@ -50,6 +57,7 @@ pwm_tacho_fixed_clk: fixedclk { pwm_tacho: pwmtachocontroller@1e786000 { #address-cells = <1>; #size-cells = <1>; + #cooling-cells = <2>; reg = <0x1E786000 0x1000>; compatible = "aspeed,ast2500-pwm-tacho"; clocks = <&pwm_tacho_fixed_clk>; @@ -58,6 +66,7 @@ pwm_tacho: pwmtachocontroller@1e786000 { fan@0 { reg = <0x00>; + cooling-levels = /bits/ 8 <125 151 177 203 229 255>; aspeed,fan-tach-ch = /bits/ 8 <0x00>; }; diff --git a/Documentation/devicetree/bindings/hwmon/ibm,cffps1.txt b/Documentation/devicetree/bindings/hwmon/ibm,cffps1.txt new file mode 100644 index 000000000000..f68a0a68fc52 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ibm,cffps1.txt @@ -0,0 +1,21 @@ +Device-tree bindings for IBM Common Form Factor Power Supply Version 1 +---------------------------------------------------------------------- + +Required properties: + - compatible = "ibm,cffps1"; + - reg = < I2C bus address >; : Address of the power supply on the + I2C bus. + +Example: + + i2c-bus@100 { + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + < more properties > + + power-supply@68 { + compatible = "ibm,cffps1"; + reg = <0x68>; + }; + }; diff --git a/Documentation/devicetree/bindings/hwmon/ltq-cputemp.txt b/Documentation/devicetree/bindings/hwmon/ltq-cputemp.txt new file mode 100644 index 000000000000..33fd00a987c7 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ltq-cputemp.txt @@ -0,0 +1,10 @@ +Lantiq cpu temperatur sensor + +Requires node properties: +- compatible value : + "lantiq,cputemp" + +Example: + cputemp@0 { + compatible = "lantiq,cputemp"; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-altera.txt b/Documentation/devicetree/bindings/i2c/i2c-altera.txt new file mode 100644 index 000000000000..767664f448ec --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-altera.txt @@ -0,0 +1,39 @@ +* Altera I2C Controller +* This is Altera's synthesizable logic block I2C Controller for use +* in Altera's FPGAs. + +Required properties : + - compatible : should be "altr,softip-i2c-v1.0" + - reg : Offset and length of the register set for the device + - interrupts : <IRQ> where IRQ is the interrupt number. + - clocks : phandle to input clock. + - #address-cells = <1>; + - #size-cells = <0>; + +Recommended properties : + - clock-frequency : desired I2C bus clock frequency in Hz. + +Optional properties : + - fifo-size : Size of the RX and TX FIFOs in bytes. + - Child nodes conforming to i2c bus binding + +Example : + + i2c@100080000 { + compatible = "altr,softip-i2c-v1.0"; + reg = <0x00000001 0x00080000 0x00000040>; + interrupt-parent = <&intc>; + interrupts = <0 43 4>; + clocks = <&clk_0>; + clock-frequency = <100000>; + #address-cells = <1>; + #size-cells = <0>; + fifo-size = <4>; + + eeprom@51 { + compatible = "atmel,24c32"; + reg = <0x51>; + pagesize = <32>; + }; + }; + diff --git a/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt index 8ce9cd2855b5..c143948b2a37 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt @@ -20,8 +20,8 @@ i2c@0 { #address-cells = <1>; #size-cells = <0>; - retu-mfd: retu@1 { - compatible = "retu-mfd"; + retu: retu@1 { + compatible = "nokia,retu"; reg = <0x1>; }; }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt index 7ce23ac61308..81b5d55086fa 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt @@ -102,7 +102,6 @@ And for clarification, here are the snipplets for the i2c-parents: #address-cells = <1>; #size-cells = <0>; compatible = "i2c-gpio"; - status = "disabled"; gpios = <&gpio5 6 GPIO_ACTIVE_HIGH /* sda */ &gpio5 5 GPIO_ACTIVE_HIGH /* scl */ >; diff --git a/Documentation/devicetree/bindings/i2c/i2c-efm32.txt b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt index 50b25c3da186..3b30e54ae3c7 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-efm32.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt @@ -22,7 +22,6 @@ Example: interrupts = <9>; clocks = <&cmu clk_HFPERCLKI2C0>; clock-frequency = <100000>; - status = "ok"; energymicro,location = <3>; eeprom@50 { diff --git a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt index bd5a7befd951..ff7bf37deb43 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt @@ -1,14 +1,15 @@ -* Mediatek's I2C controller +* MediaTek's I2C controller -The Mediatek's I2C controller is used to interface with I2C devices. +The MediaTek's I2C controller is used to interface with I2C devices. Required properties: - compatible: value should be either of the following. - "mediatek,mt2701-i2c", "mediatek,mt6577-i2c": for Mediatek mt2701 - "mediatek,mt6577-i2c": for i2c compatible with mt6577. - "mediatek,mt6589-i2c": for i2c compatible with mt6589. - "mediatek,mt7623-i2c", "mediatek,mt6577-i2c": for i2c compatible with mt7623. - "mediatek,mt8173-i2c": for i2c compatible with mt8173. + "mediatek,mt2701-i2c", "mediatek,mt6577-i2c": for MediaTek MT2701 + "mediatek,mt6577-i2c": for MediaTek MT6577 + "mediatek,mt6589-i2c": for MediaTek MT6589 + "mediatek,mt7622-i2c": for MediaTek MT7622 + "mediatek,mt7623-i2c", "mediatek,mt6577-i2c": for MediaTek MT7623 + "mediatek,mt8173-i2c": for MediaTek MT8173 - reg: physical base address of the controller and dma base, length of memory mapped region. - interrupts: interrupt number to the cpu. diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index 2b8bd33dbf8d..cad39aee9f73 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -2,6 +2,8 @@ I2C for R-Car platforms Required properties: - compatible: + "renesas,i2c-r8a7743" if the device is a part of a R8A7743 SoC. + "renesas,i2c-r8a7745" if the device is a part of a R8A7745 SoC. "renesas,i2c-r8a7778" if the device is a part of a R8A7778 SoC. "renesas,i2c-r8a7779" if the device is a part of a R8A7779 SoC. "renesas,i2c-r8a7790" if the device is a part of a R8A7790 SoC. @@ -12,7 +14,8 @@ Required properties: "renesas,i2c-r8a7795" if the device is a part of a R8A7795 SoC. "renesas,i2c-r8a7796" if the device is a part of a R8A7796 SoC. "renesas,rcar-gen1-i2c" for a generic R-Car Gen1 compatible device. - "renesas,rcar-gen2-i2c" for a generic R-Car Gen2 compatible device. + "renesas,rcar-gen2-i2c" for a generic R-Car Gen2 or RZ/G1 compatible + device. "renesas,rcar-gen3-i2c" for a generic R-Car Gen3 compatible device. "renesas,i2c-rcar" (deprecated) diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt index e18445d0980c..22f2eeb2c4c9 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt @@ -7,6 +7,7 @@ Required properties : - reg : Offset and length of the register set for the device - compatible: should be one of the following: + - "rockchip,rv1108-i2c": for rv1108 - "rockchip,rk3066-i2c": for rk3066 - "rockchip,rk3188-i2c": for rk3188 - "rockchip,rk3228-i2c": for rk3228 diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt index ae9c2a735f39..224390999e81 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -4,6 +4,8 @@ Required properties: - compatible : - "renesas,iic-r8a73a4" (R-Mobile APE6) - "renesas,iic-r8a7740" (R-Mobile A1) + - "renesas,iic-r8a7743" (RZ/G1M) + - "renesas,iic-r8a7745" (RZ/G1E) - "renesas,iic-r8a7790" (R-Car H2) - "renesas,iic-r8a7791" (R-Car M2-W) - "renesas,iic-r8a7792" (R-Car V2H) @@ -12,7 +14,8 @@ Required properties: - "renesas,iic-r8a7795" (R-Car H3) - "renesas,iic-r8a7796" (R-Car M3-W) - "renesas,iic-sh73a0" (SH-Mobile AG5) - - "renesas,rcar-gen2-iic" (generic R-Car Gen2 compatible device) + - "renesas,rcar-gen2-iic" (generic R-Car Gen2 or RZ/G1 + compatible device) - "renesas,rcar-gen3-iic" (generic R-Car Gen3 compatible device) - "renesas,rmobile-iic" (generic device) diff --git a/Documentation/devicetree/bindings/i2c/i2c-sprd.txt b/Documentation/devicetree/bindings/i2c/i2c-sprd.txt new file mode 100644 index 000000000000..60b7cda15dd2 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-sprd.txt @@ -0,0 +1,31 @@ +I2C for Spreadtrum platforms + +Required properties: +- compatible: Should be "sprd,sc9860-i2c". +- reg: Specify the physical base address of the controller and length + of memory mapped region. +- interrupts: Should contain I2C interrupt. +- clock-names: Should contain following entries: + "i2c" for I2C clock, + "source" for I2C source (parent) clock, + "enable" for I2C module enable clock. +- clocks: Should contain a clock specifier for each entry in clock-names. +- clock-frequency: Constains desired I2C bus clock frequency in Hz. +- #address-cells: Should be 1 to describe address cells for I2C device address. +- #size-cells: Should be 0 means no size cell for I2C device address. + +Optional properties: +- Child nodes conforming to I2C bus binding + +Examples: +i2c0: i2c@70500000 { + compatible = "sprd,sc9860-i2c"; + reg = <0 0x70500000 0 0x1000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "i2c", "source", "enable"; + clocks = <&clk_i2c3>, <&ext_26m>, <&clk_ap_apb_gates 11>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; +}; + diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt index 78eaf7b718ed..3b5489966634 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt @@ -1,7 +1,9 @@ * I2C controller embedded in STMicroelectronics STM32 I2C platform Required properties : -- compatible : Must be "st,stm32f4-i2c" +- compatible : Must be one of the following + - "st,stm32f4-i2c" + - "st,stm32f7-i2c" - reg : Offset and length of the register set for the device - interrupts : Must contain the interrupt id for I2C event and then the interrupt id for I2C error. @@ -14,8 +16,16 @@ Required properties : Optional properties : - clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, - the default 100 kHz frequency will be used. As only Normal and Fast modes - are supported, possible values are 100000 and 400000. + the default 100 kHz frequency will be used. + For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are + 100000 and 400000. + For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, + possible values are 100000, 400000 and 1000000. +- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board + (default: 25) +- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board + (default: 10) + I2C Timings are derived from these 2 values Example : @@ -31,3 +41,16 @@ Example : pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>; pinctrl-names = "default"; }; + + i2c@40005400 { + compatible = "st,stm32f7-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x40005400 0x400>; + interrupts = <31>, + <32>; + resets = <&rcc STM32F7_APB1_RESET(I2C1)>; + clocks = <&rcc 1 CLK_I2C1>; + pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>; + pinctrl-names = "default"; + }; diff --git a/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt index 656716b72cc4..f64064f8bdc2 100644 --- a/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt @@ -71,5 +71,4 @@ Example: reset-names = "i2c"; dmas = <&apbdma 16>, <&apbdma 16>; dma-names = "rx", "tx"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt index 3223684a643b..552e7a83951d 100644 --- a/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt @@ -11,6 +11,11 @@ Required properties: - atmel,min-sample-rate-hz: Minimum sampling rate, it depends on SoC. - atmel,max-sample-rate-hz: Maximum sampling rate, it depends on SoC. - atmel,startup-time-ms: Startup time expressed in ms, it depends on SoC. + - atmel,trigger-edge-type: One of possible edge types for the ADTRG hardware + trigger pin. When the specific edge type is detected, the conversion will + start. Possible values are rising, falling, or both. + This property uses the IRQ edge types values: IRQ_TYPE_EDGE_RISING , + IRQ_TYPE_EDGE_FALLING or IRQ_TYPE_EDGE_BOTH Example: @@ -25,4 +30,5 @@ adc: adc@fc030000 { atmel,startup-time-ms = <4>; vddana-supply = <&vdd_3v3_lp_reg>; vref-supply = <&vdd_3v3_lp_reg>; + atmel,trigger-edge-type = <IRQ_TYPE_EDGE_BOTH>; } diff --git a/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt b/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt index caaaed765ce4..7b1b1e4086d4 100644 --- a/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt @@ -37,5 +37,4 @@ For example: clocks = <&asiu_clks BCM_CYGNUS_ASIU_ADC_CLK>; clock-names = "tsc_clk"; interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/iio/adc/lpc1850-adc.txt b/Documentation/devicetree/bindings/iio/adc/lpc1850-adc.txt index 0bcae5140bc5..9ada5abd45fa 100644 --- a/Documentation/devicetree/bindings/iio/adc/lpc1850-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/lpc1850-adc.txt @@ -17,5 +17,4 @@ adc0: adc@400e3000 { clocks = <&ccu1 CLK_APB3_ADC0>; vref-supply = <®_vdda>; resets = <&rgu 40>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt b/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt index 68c45cbbe3d9..64dc4843c180 100644 --- a/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt +++ b/Documentation/devicetree/bindings/iio/adc/mt6577_auxadc.txt @@ -12,6 +12,7 @@ for the Thermal Controller which holds a phandle to the AUXADC. Required properties: - compatible: Should be one of: - "mediatek,mt2701-auxadc": For MT2701 family of SoCs + - "mediatek,mt7622-auxadc": For MT7622 family of SoCs - "mediatek,mt8173-auxadc": For MT8173 family of SoCs - reg: Address range of the AUXADC unit. - clocks: Should contain a clock specifier for each entry in clock-names diff --git a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt index e0a9b9d6d6fd..c2c50b59873d 100644 --- a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt +++ b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt @@ -6,6 +6,7 @@ Required properties: - "rockchip,rk3066-tsadc": for rk3036 - "rockchip,rk3328-saradc", "rockchip,rk3399-saradc": for rk3328 - "rockchip,rk3399-saradc": for rk3399 + - "rockchip,rv1108-saradc", "rockchip,rk3399-saradc": for rv1108 - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt index 8310073f14e1..48bfcaa3ffcd 100644 --- a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt @@ -74,6 +74,11 @@ Optional properties: * can be 6, 8, 10 or 12 on stm32f4 * can be 8, 10, 12, 14 or 16 on stm32h7 Default is maximum resolution if unset. +- st,min-sample-time-nsecs: Minimum sampling time in nanoseconds. + Depending on hardware (board) e.g. high/low analog input source impedance, + fine tune of ADC sampling time may be recommended. + This can be either one value or an array that matches 'st,adc-channels' list, + to set sample time resp. for all channels, or independently for each channel. Example: adc: adc@40012000 { diff --git a/Documentation/devicetree/bindings/iio/counter/stm32-lptimer-cnt.txt b/Documentation/devicetree/bindings/iio/counter/stm32-lptimer-cnt.txt new file mode 100644 index 000000000000..a04aa5c04103 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/counter/stm32-lptimer-cnt.txt @@ -0,0 +1,27 @@ +STMicroelectronics STM32 Low-Power Timer quadrature encoder and counter + +STM32 Low-Power Timer provides several counter modes. It can be used as: +- quadrature encoder to detect angular position and direction of rotary + elements, from IN1 and IN2 input signals. +- simple counter from IN1 input signal. + +Must be a sub-node of an STM32 Low-Power Timer device tree node. +See ../mfd/stm32-lptimer.txt for details about the parent node. + +Required properties: +- compatible: Must be "st,stm32-lptimer-counter". +- pinctrl-names: Set to "default". +- pinctrl-0: List of phandles pointing to pin configuration nodes, + to set IN1/IN2 pins in mode of operation for Low-Power + Timer input on external pin. + +Example: + timer@40002400 { + compatible = "st,stm32-lptimer"; + ... + counter { + compatible = "st,stm32-lptimer-counter"; + pinctrl-names = "default"; + pinctrl-0 = <&lptim1_in_pins>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt b/Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt index 7d6647d4af5e..42db783c4e75 100644 --- a/Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt +++ b/Documentation/devicetree/bindings/iio/dac/lpc1850-dac.txt @@ -16,5 +16,4 @@ dac: dac@400e1000 { clocks = <&ccu1 CLK_APB3_DAC>; vref-supply = <®_vdda>; resets = <&rgu 42>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.txt b/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.txt index bcee71f808d0..bf2925c671c6 100644 --- a/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.txt +++ b/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.txt @@ -10,7 +10,9 @@ current. Contents of a stm32 dac root node: ----------------------------------- Required properties: -- compatible: Must be "st,stm32h7-dac-core". +- compatible: Should be one of: + "st,stm32f4-dac-core" + "st,stm32h7-dac-core" - reg: Offset and length of the device's register set. - clocks: Must contain an entry for pclk (which feeds the peripheral bus interface) diff --git a/Documentation/devicetree/bindings/iio/humidity/hdc100x.txt b/Documentation/devicetree/bindings/iio/humidity/hdc100x.txt new file mode 100644 index 000000000000..c52333bdfd19 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/humidity/hdc100x.txt @@ -0,0 +1,17 @@ +* HDC100x temperature + humidity sensors + +Required properties: + - compatible: Should contain one of the following: + ti,hdc1000 + ti,hdc1008 + ti,hdc1010 + ti,hdc1050 + ti,hdc1080 + - reg: i2c address of the sensor + +Example: + +hdc100x@40 { + compatible = "ti,hdc1000"; + reg = <0x40>; +}; diff --git a/Documentation/devicetree/bindings/iio/humidity/hts221.txt b/Documentation/devicetree/bindings/iio/humidity/hts221.txt index b20ab9c12080..10adeb0d703d 100644 --- a/Documentation/devicetree/bindings/iio/humidity/hts221.txt +++ b/Documentation/devicetree/bindings/iio/humidity/hts221.txt @@ -5,9 +5,18 @@ Required properties: - reg: i2c address of the sensor / spi cs line Optional properties: +- drive-open-drain: the interrupt/data ready line will be configured + as open drain, which is useful if several sensors share the same + interrupt line. This is a boolean property. + If the requested interrupt is configured as IRQ_TYPE_LEVEL_HIGH or + IRQ_TYPE_EDGE_RISING a pull-down resistor is needed to drive the line + when it is not active, whereas a pull-up one is needed when interrupt + line is configured as IRQ_TYPE_LEVEL_LOW or IRQ_TYPE_EDGE_FALLING. + Refer to pinctrl/pinctrl-bindings.txt for the property description. - interrupt-parent: should be the phandle for the interrupt controller - interrupts: interrupt mapping for IRQ. It should be configured with - flags IRQ_TYPE_LEVEL_HIGH or IRQ_TYPE_EDGE_RISING. + flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or + IRQ_TYPE_EDGE_FALLING. Refer to interrupt-controller/interrupts.txt for generic interrupt client node bindings. diff --git a/Documentation/devicetree/bindings/iio/humidity/htu21.txt b/Documentation/devicetree/bindings/iio/humidity/htu21.txt new file mode 100644 index 000000000000..97d79636f7ae --- /dev/null +++ b/Documentation/devicetree/bindings/iio/humidity/htu21.txt @@ -0,0 +1,13 @@ +*HTU21 - Measurement-Specialties htu21 temperature & humidity sensor and humidity part of MS8607 sensor + +Required properties: + + - compatible: should be "meas,htu21" or "meas,ms8607-humidity" + - reg: I2C address of the sensor + +Example: + +htu21@40 { + compatible = "meas,htu21"; + reg = <0x40>; +}; diff --git a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt index 6f28ff55f3ec..1ff1af799c76 100644 --- a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt +++ b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt @@ -11,6 +11,14 @@ Required properties: Optional properties: - st,drdy-int-pin: the pin on the package that will be used to signal "data ready" (valid values: 1 or 2). +- drive-open-drain: the interrupt/data ready line will be configured + as open drain, which is useful if several sensors share the same + interrupt line. This is a boolean property. + (This binding is taken from pinctrl/pinctrl-bindings.txt) + If the requested interrupt is configured as IRQ_TYPE_LEVEL_HIGH or + IRQ_TYPE_EDGE_RISING a pull-down resistor is needed to drive the line + when it is not active, whereas a pull-up one is needed when interrupt + line is configured as IRQ_TYPE_LEVEL_LOW or IRQ_TYPE_EDGE_FALLING. - interrupt-parent: should be the phandle for the interrupt controller - interrupts: interrupt mapping for IRQ. It should be configured with flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or diff --git a/Documentation/devicetree/bindings/iio/pressure/ms5637.txt b/Documentation/devicetree/bindings/iio/pressure/ms5637.txt new file mode 100644 index 000000000000..1f43ffa068ac --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/ms5637.txt @@ -0,0 +1,17 @@ +* MS5637 - Measurement-Specialties MS5637, MS5805, MS5837 and MS8607 pressure & temperature sensor + +Required properties: + + -compatible: should be one of the following + meas,ms5637 + meas,ms5805 + meas,ms5837 + meas,ms8607-temppressure + -reg: I2C address of the sensor + +Example: + +ms5637@76 { + compatible = "meas,ms5637"; + reg = <0x76>; +}; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index eaa8fbba34e2..9ec6f5ce54fc 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -45,6 +45,7 @@ Accelerometers: - st,lis2dh12-accel - st,h3lis331dl-accel - st,lng2dm-accel +- st,lis3l02dq Gyroscopes: - st,l3g4200d-gyro @@ -52,6 +53,7 @@ Gyroscopes: - st,lsm330dl-gyro - st,lsm330dlc-gyro - st,l3gd20-gyro +- st,l3gd20h-gyro - st,l3g4is-gyro - st,lsm330-gyro - st,lsm9ds0-gyro @@ -62,6 +64,7 @@ Magnetometers: - st,lsm303dlhc-magn - st,lsm303dlm-magn - st,lis3mdl-magn +- st,lis2mdl Pressure sensors: - st,lps001wp-press diff --git a/Documentation/devicetree/bindings/iio/temperature/tsys01.txt b/Documentation/devicetree/bindings/iio/temperature/tsys01.txt new file mode 100644 index 000000000000..0d5cc5595d0c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/tsys01.txt @@ -0,0 +1,19 @@ +* TSYS01 - Measurement Specialties temperature sensor + +Required properties: + + - compatible: should be "meas,tsys01" + - reg: I2C address of the sensor (changeable via CSB pin) + + ------------------------ + | CSB | Device Address | + ------------------------ + 1 0x76 + 0 0x77 + +Example: + +tsys01@76 { + compatible = "meas,tsys01"; + reg = <0x76>; +}; diff --git a/Documentation/devicetree/bindings/iio/timer/stm32-lptimer-trigger.txt b/Documentation/devicetree/bindings/iio/timer/stm32-lptimer-trigger.txt new file mode 100644 index 000000000000..85e6806b17d7 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/timer/stm32-lptimer-trigger.txt @@ -0,0 +1,23 @@ +STMicroelectronics STM32 Low-Power Timer Trigger + +STM32 Low-Power Timer provides trigger source (LPTIM output) that can be used +by STM32 internal ADC and/or DAC. + +Must be a sub-node of an STM32 Low-Power Timer device tree node. +See ../mfd/stm32-lptimer.txt for details about the parent node. + +Required properties: +- compatible: Must be "st,stm32-lptimer-trigger". +- reg: Identify trigger hardware block. Must be 0, 1 or 2 + respectively for lptimer1, lptimer2 or lptimer3 + trigger output. + +Example: + timer@40002400 { + compatible = "st,stm32-lptimer"; + ... + trigger@0 { + compatible = "st,stm32-lptimer-trigger"; + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt b/Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt index 55a653d15303..b8e8c769d434 100644 --- a/Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt +++ b/Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt @@ -4,7 +4,9 @@ Must be a sub-node of an STM32 Timers device tree node. See ../mfd/stm32-timers.txt for details about the parent node. Required parameters: -- compatible: Must be "st,stm32-timer-trigger". +- compatible: Must be one of: + "st,stm32-timer-trigger" + "st,stm32h7-timer-trigger" - reg: Identify trigger hardware block. Example: @@ -14,7 +16,7 @@ Example: compatible = "st,stm32-timers"; reg = <0x40010000 0x400>; clocks = <&rcc 0 160>; - clock-names = "clk_int"; + clock-names = "int"; timer@0 { compatible = "st,stm32-timer-trigger"; diff --git a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt index 1852906517ab..23e3abc3fdef 100644 --- a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt +++ b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt @@ -22,6 +22,8 @@ Optional properties for main touchpad device: experiment to determine which bit corresponds to which input. Use KEY_RESERVED for unused padding values. +- reset-gpios: GPIO specifier for the touchscreen's reset pin (active low) + Example: touch@4b { diff --git a/Documentation/devicetree/bindings/input/brcm,bcm-keypad.txt b/Documentation/devicetree/bindings/input/brcm,bcm-keypad.txt index b77f50bd6403..262deab73588 100644 --- a/Documentation/devicetree/bindings/input/brcm,bcm-keypad.txt +++ b/Documentation/devicetree/bindings/input/brcm,bcm-keypad.txt @@ -72,7 +72,6 @@ Example: /* Required Board specific properties */ keypad,num-rows = <5>; keypad,num-columns = <5>; - status = "okay"; linux,keymap = <MATRIX_KEY(0x00, 0x02, KEY_F) /* key_forward */ MATRIX_KEY(0x00, 0x03, KEY_HOME) /* key_home */ diff --git a/Documentation/devicetree/bindings/input/pwm-vibrator.txt b/Documentation/devicetree/bindings/input/pwm-vibrator.txt new file mode 100644 index 000000000000..09145d18491d --- /dev/null +++ b/Documentation/devicetree/bindings/input/pwm-vibrator.txt @@ -0,0 +1,66 @@ +* PWM vibrator device tree bindings + +Registers a PWM device as vibrator. It is expected, that the vibrator's +strength increases based on the duty cycle of the enable PWM channel +(100% duty cycle meaning strongest vibration, 0% meaning no vibration). + +The binding supports an optional direction PWM channel, that can be +driven at fixed duty cycle. If available this is can be used to increase +the vibration effect of some devices. + +Required properties: +- compatible: should contain "pwm-vibrator" +- pwm-names: Should contain "enable" and optionally "direction" +- pwms: Should contain a PWM handle for each entry in pwm-names + +Optional properties: +- vcc-supply: Phandle for the regulator supplying power +- direction-duty-cycle-ns: Duty cycle of the direction PWM channel in + nanoseconds, defaults to 50% of the channel's + period. + +Example from Motorola Droid 4: + +&omap4_pmx_core { + vibrator_direction_pin: pinmux_vibrator_direction_pin { + pinctrl-single,pins = < + OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1) /* dmtimer8_pwm_evt (gpio_27) */ + >; + }; + + vibrator_enable_pin: pinmux_vibrator_enable_pin { + pinctrl-single,pins = < + OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1) /* dmtimer9_pwm_evt (gpio_28) */ + >; + }; +}; + +/ { + pwm8: dmtimer-pwm { + pinctrl-names = "default"; + pinctrl-0 = <&vibrator_direction_pin>; + + compatible = "ti,omap-dmtimer-pwm"; + #pwm-cells = <3>; + ti,timers = <&timer8>; + ti,clock-source = <0x01>; + }; + + pwm9: dmtimer-pwm { + pinctrl-names = "default"; + pinctrl-0 = <&vibrator_enable_pin>; + + compatible = "ti,omap-dmtimer-pwm"; + #pwm-cells = <3>; + ti,timers = <&timer9>; + ti,clock-source = <0x01>; + }; + + vibrator { + compatible = "pwm-vibrator"; + pwms = <&pwm8 0 1000000000 0>, + <&pwm9 0 1000000000 0>; + pwm-names = "enable", "direction"; + direction-duty-cycle-ns = <1000000000>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/ti,drv260x.txt b/Documentation/devicetree/bindings/input/ti,drv260x.txt index ee09c8f4474a..4c5312eaaa85 100644 --- a/Documentation/devicetree/bindings/input/ti,drv260x.txt +++ b/Documentation/devicetree/bindings/input/ti,drv260x.txt @@ -43,7 +43,7 @@ haptics: haptics@5a { mode = <DRV260X_LRA_MODE>; library-sel = <DRV260X_LIB_LRA>; vib-rated-mv = <3200>; - vib-overdriver-mv = <3200>; + vib-overdrive-mv = <3200>; } For more product information please see the link below: diff --git a/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt index 9d9e930f3251..df531b5b6a0d 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt @@ -32,5 +32,4 @@ Example: pinctrl-1 = <&pinctrl_touchctrl_default>; pinctrl-2 = <&pinctrl_touchctrl_gpios>; vf50-ts-min-pressure = <200>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt index d4927c202aef..e67e58b61706 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt @@ -35,5 +35,4 @@ Example: measure-delay-time = <0xfff>; pre-charge-time = <0xffff>; touchscreen-average-samples = <32>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt b/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt index 9e389493203f..49ccabbfa6f3 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt @@ -4,8 +4,10 @@ Required properties: - compatible: should be "fsl,<soc-name>-msi" to identify Layerscape PCIe MSI controller block such as: - "fsl,1s1021a-msi" - "fsl,1s1043a-msi" + "fsl,ls1021a-msi" + "fsl,ls1043a-msi" + "fsl,ls1046a-msi" + "fsl,ls1043a-v1.1-msi" - msi-controller: indicates that this is a PCIe MSI controller node - reg: physical base address of the controller and length of memory mapped. - interrupts: an interrupt to the parent interrupt controller. @@ -23,7 +25,7 @@ MSI controller node Examples: msi1: msi-controller@1571000 { - compatible = "fsl,1s1043a-msi"; + compatible = "fsl,ls1043a-msi"; reg = <0x0 0x1571000 0x0 0x8>, msi-controller; interrupts = <0 116 0x4>; diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt index 11cc87aeb276..07bf0b9a5139 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt @@ -17,6 +17,7 @@ Required properties: "mediatek,mt6582-sysirq", "mediatek,mt6577-sysirq": for MT6582 "mediatek,mt6580-sysirq", "mediatek,mt6577-sysirq": for MT6580 "mediatek,mt6577-sysirq": for MT6577 + "mediatek,mt2712-sysirq", "mediatek,mt6577-sysirq": for MT2712 "mediatek,mt2701-sysirq", "mediatek,mt6577-sysirq": for MT2701 - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Use the same format as specified by GIC in arm,gic.txt. diff --git a/Documentation/devicetree/bindings/interrupt-controller/socionext,uniphier-aidet.txt b/Documentation/devicetree/bindings/interrupt-controller/socionext,uniphier-aidet.txt new file mode 100644 index 000000000000..48e71d3ac2ad --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/socionext,uniphier-aidet.txt @@ -0,0 +1,32 @@ +UniPhier AIDET + +UniPhier AIDET (ARM Interrupt Detector) is an add-on block for ARM GIC (Generic +Interrupt Controller). GIC itself can handle only high level and rising edge +interrupts. The AIDET provides logic inverter to support low level and falling +edge interrupts. + +Required properties: +- compatible: Should be one of the following: + "socionext,uniphier-ld4-aidet" - for LD4 SoC + "socionext,uniphier-pro4-aidet" - for Pro4 SoC + "socionext,uniphier-sld8-aidet" - for sLD8 SoC + "socionext,uniphier-pro5-aidet" - for Pro5 SoC + "socionext,uniphier-pxs2-aidet" - for PXs2/LD6b SoC + "socionext,uniphier-ld11-aidet" - for LD11 SoC + "socionext,uniphier-ld20-aidet" - for LD20 SoC + "socionext,uniphier-pxs3-aidet" - for PXs3 SoC +- reg: Specifies offset and length of the register set for the device. +- interrupt-controller: Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an interrupt + source. The value should be 2. The first cell defines the interrupt number + (corresponds to the SPI interrupt number of GIC). The second cell specifies + the trigger type as defined in interrupts.txt in this directory. + +Example: + + aidet: aidet@5fc20000 { + compatible = "socionext,uniphier-pro4-aidet"; + reg = <0x5fc20000 0x200>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/iommu/qcom,iommu.txt b/Documentation/devicetree/bindings/iommu/qcom,iommu.txt new file mode 100644 index 000000000000..b2641ceb2b40 --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/qcom,iommu.txt @@ -0,0 +1,121 @@ +* QCOM IOMMU v1 Implementation + +Qualcomm "B" family devices which are not compatible with arm-smmu have +a similar looking IOMMU but without access to the global register space, +and optionally requiring additional configuration to route context irqs +to non-secure vs secure interrupt line. + +** Required properties: + +- compatible : Should be one of: + + "qcom,msm8916-iommu" + + Followed by "qcom,msm-iommu-v1". + +- clock-names : Should be a pair of "iface" (required for IOMMUs + register group access) and "bus" (required for + the IOMMUs underlying bus access). + +- clocks : Phandles for respective clocks described by + clock-names. + +- #address-cells : must be 1. + +- #size-cells : must be 1. + +- #iommu-cells : Must be 1. Index identifies the context-bank #. + +- ranges : Base address and size of the iommu context banks. + +- qcom,iommu-secure-id : secure-id. + +- List of sub-nodes, one per translation context bank. Each sub-node + has the following required properties: + + - compatible : Should be one of: + - "qcom,msm-iommu-v1-ns" : non-secure context bank + - "qcom,msm-iommu-v1-sec" : secure context bank + - reg : Base address and size of context bank within the iommu + - interrupts : The context fault irq. + +** Optional properties: + +- reg : Base address and size of the SMMU local base, should + be only specified if the iommu requires configuration + for routing of context bank irq's to secure vs non- + secure lines. (Ie. if the iommu contains secure + context banks) + + +** Examples: + + apps_iommu: iommu@1e20000 { + #address-cells = <1>; + #size-cells = <1>; + #iommu-cells = <1>; + compatible = "qcom,msm8916-iommu", "qcom,msm-iommu-v1"; + ranges = <0 0x1e20000 0x40000>; + reg = <0x1ef0000 0x3000>; + clocks = <&gcc GCC_SMMU_CFG_CLK>, + <&gcc GCC_APSS_TCU_CLK>; + clock-names = "iface", "bus"; + qcom,iommu-secure-id = <17>; + + // mdp_0: + iommu-ctx@4000 { + compatible = "qcom,msm-iommu-v1-ns"; + reg = <0x4000 0x1000>; + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + }; + + // venus_ns: + iommu-ctx@5000 { + compatible = "qcom,msm-iommu-v1-sec"; + reg = <0x5000 0x1000>; + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpu_iommu: iommu@1f08000 { + #address-cells = <1>; + #size-cells = <1>; + #iommu-cells = <1>; + compatible = "qcom,msm8916-iommu", "qcom,msm-iommu-v1"; + ranges = <0 0x1f08000 0x10000>; + clocks = <&gcc GCC_SMMU_CFG_CLK>, + <&gcc GCC_GFX_TCU_CLK>; + clock-names = "iface", "bus"; + qcom,iommu-secure-id = <18>; + + // gfx3d_user: + iommu-ctx@1000 { + compatible = "qcom,msm-iommu-v1-ns"; + reg = <0x1000 0x1000>; + interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>; + }; + + // gfx3d_priv: + iommu-ctx@2000 { + compatible = "qcom,msm-iommu-v1-ns"; + reg = <0x2000 0x1000>; + interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + ... + + venus: video-codec@1d00000 { + ... + iommus = <&apps_iommu 5>; + }; + + mdp: mdp@1a01000 { + ... + iommus = <&apps_iommu 4>; + }; + + gpu@01c00000 { + ... + iommus = <&gpu_iommu 1>, <&gpu_iommu 2>; + }; diff --git a/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt b/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt index 9a55ac3735e5..2098f7732264 100644 --- a/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt +++ b/Documentation/devicetree/bindings/iommu/rockchip,iommu.txt @@ -15,6 +15,11 @@ Required properties: to associate with its master device. See: Documentation/devicetree/bindings/iommu/iommu.txt +Optional properties: +- rockchip,disable-mmu-reset : Don't use the mmu reset operation. + Some mmu instances may produce unexpected results + when the reset operation is used. + Example: vopl_mmu: iommu@ff940300 { diff --git a/Documentation/devicetree/bindings/leds/ams,as3645a.txt b/Documentation/devicetree/bindings/leds/ams,as3645a.txt new file mode 100644 index 000000000000..fdc40e354a64 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/ams,as3645a.txt @@ -0,0 +1,79 @@ +Analog devices AS3645A device tree bindings + +The AS3645A flash LED controller can drive two LEDs, one high current +flash LED and one indicator LED. The high current flash LED can be +used in torch mode as well. + +Ranges below noted as [a, b] are closed ranges between a and b, i.e. a +and b are included in the range. + +Please also see common.txt in the same directory. + + +Required properties +=================== + +compatible : Must be "ams,as3645a". +reg : The I2C address of the device. Typically 0x30. +#address-cells : 1 +#size-cells : 0 + + +Required properties of the flash child node (0) +=============================================== + +reg: 0 +flash-timeout-us: Flash timeout in microseconds. The value must be in + the range [100000, 850000] and divisible by 50000. +flash-max-microamp: Maximum flash current in microamperes. Has to be + in the range between [200000, 500000] and + divisible by 20000. +led-max-microamp: Maximum torch (assist) current in microamperes. The + value must be in the range between [20000, 160000] and + divisible by 20000. +ams,input-max-microamp: Maximum flash controller input current. The + value must be in the range [1250000, 2000000] + and divisible by 50000. + + +Optional properties of the flash child node +=========================================== + +label : The label of the flash LED. + + +Required properties of the indicator child node (1) +=================================================== + +reg: 1 +led-max-microamp: Maximum indicator current. The allowed values are + 2500, 5000, 7500 and 10000. + +Optional properties of the indicator child node +=============================================== + +label : The label of the indicator LED. + + +Example +======= + + as3645a@30 { + #address-cells: 1 + #size-cells: 0 + reg = <0x30>; + compatible = "ams,as3645a"; + flash@0 { + reg = <0x0>; + flash-timeout-us = <150000>; + flash-max-microamp = <320000>; + led-max-microamp = <60000>; + ams,input-max-microamp = <1750000>; + label = "as3645a:flash"; + }; + indicator@1 { + reg = <0x1>; + led-max-microamp = <10000>; + label = "as3645a:indicator"; + }; + }; diff --git a/Documentation/devicetree/bindings/leds/irled/gpio-ir-tx.txt b/Documentation/devicetree/bindings/leds/irled/gpio-ir-tx.txt new file mode 100644 index 000000000000..cbe8dfd29715 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/irled/gpio-ir-tx.txt @@ -0,0 +1,14 @@ +Device tree bindings for IR LED connected through gpio pin which is used as +remote controller transmitter. + +Required properties: + - compatible: should be "gpio-ir-tx". + - gpios : Should specify the IR LED GPIO, see "gpios property" in + Documentation/devicetree/bindings/gpio/gpio.txt. Active low LEDs + should be indicated using flags in the GPIO specifier. + +Example: + irled@0 { + compatible = "gpio-ir-tx"; + gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/leds/irled/pwm-ir-tx.txt b/Documentation/devicetree/bindings/leds/irled/pwm-ir-tx.txt new file mode 100644 index 000000000000..66e5672c2e3d --- /dev/null +++ b/Documentation/devicetree/bindings/leds/irled/pwm-ir-tx.txt @@ -0,0 +1,13 @@ +Device tree bindings for IR LED connected through pwm pin which is used as +remote controller transmitter. + +Required properties: + - compatible: should be "pwm-ir-tx". + - pwms : PWM property to point to the PWM device (phandle)/port (id) + and to specify the period time to be used: <&phandle id period_ns>; + +Example: + irled { + compatible = "pwm-ir-tx"; + pwms = <&pwm0 0 10000000>; + }; diff --git a/Documentation/devicetree/bindings/leds/leds-gpio.txt b/Documentation/devicetree/bindings/leds/leds-gpio.txt index 76535ca37120..a48dda268f81 100644 --- a/Documentation/devicetree/bindings/leds/leds-gpio.txt +++ b/Documentation/devicetree/bindings/leds/leds-gpio.txt @@ -18,6 +18,9 @@ LED sub-node properties: see Documentation/devicetree/bindings/leds/common.txt - retain-state-suspended: (optional) The suspend state can be retained.Such as charge-led gpio. +- retain-state-shutdown: (optional) Retain the state of the LED on shutdown. + Useful in BMC systems, for example when the BMC is rebooted while the host + remains up. - panic-indicator : (optional) see Documentation/devicetree/bindings/leds/common.txt diff --git a/Documentation/devicetree/bindings/leds/leds-pca955x.txt b/Documentation/devicetree/bindings/leds/leds-pca955x.txt new file mode 100644 index 000000000000..7984efb767b4 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-pca955x.txt @@ -0,0 +1,88 @@ +* NXP - pca955x LED driver + +The PCA955x family of chips are I2C LED blinkers whose pins not used +to control LEDs can be used as general purpose I/Os. The GPIO pins can +be input or output, and output pins can also be pulse-width controlled. + +Required properties: +- compatible : should be one of : + "nxp,pca9550" + "nxp,pca9551" + "nxp,pca9552" + "nxp,pca9553" +- #address-cells: must be 1 +- #size-cells: must be 0 +- reg: I2C slave address. depends on the model. + +Optional properties: +- gpio-controller: allows pins to be used as GPIOs. +- #gpio-cells: must be 2. +- gpio-line-names: define the names of the GPIO lines + +LED sub-node properties: +- reg : number of LED line. + from 0 to 1 for the pca9550 + from 0 to 7 for the pca9551 + from 0 to 15 for the pca9552 + from 0 to 3 for the pca9553 +- type: (optional) either + PCA9532_TYPE_NONE + PCA9532_TYPE_LED + PCA9532_TYPE_GPIO + see dt-bindings/leds/leds-pca955x.h (default to LED) +- label : (optional) + see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt + +Examples: + +pca9552: pca9552@60 { + compatible = "nxp,pca9552"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x60>; + + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "GPIO12", "GPIO13", "GPIO14", "GPIO15"; + + gpio@12 { + reg = <12>; + type = <PCA955X_TYPE_GPIO>; + }; + gpio@13 { + reg = <13>; + type = <PCA955X_TYPE_GPIO>; + }; + gpio@14 { + reg = <14>; + type = <PCA955X_TYPE_GPIO>; + }; + gpio@15 { + reg = <15>; + type = <PCA955X_TYPE_GPIO>; + }; + + led@0 { + label = "red:power"; + linux,default-trigger = "default-on"; + reg = <0>; + type = <PCA955X_TYPE_LED>; + }; + led@1 { + label = "green:power"; + reg = <1>; + type = <PCA955X_TYPE_LED>; + }; + led@2 { + label = "pca9552:yellow"; + reg = <2>; + type = <PCA955X_TYPE_LED>; + }; + led@3 { + label = "pca9552:white"; + reg = <3>; + type = <PCA955X_TYPE_LED>; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt b/Documentation/devicetree/bindings/media/i2c/adv748x.txt new file mode 100644 index 000000000000..21ffb5ed8183 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv748x.txt @@ -0,0 +1,95 @@ +* Analog Devices ADV748X video decoder with HDMI receiver + +The ADV7481 and ADV7482 are multi format video decoders with an integrated +HDMI receiver. They can output CSI-2 on two independent outputs TXA and TXB +from three input sources HDMI, analog and TTL. + +Required Properties: + + - compatible: Must contain one of the following + - "adi,adv7481" for the ADV7481 + - "adi,adv7482" for the ADV7482 + + - reg: I2C slave address + +Optional Properties: + + - interrupt-names: Should specify the interrupts as "intrq1", "intrq2" and/or + "intrq3". All interrupts are optional. The "intrq3" interrupt + is only available on the adv7481 + - interrupts: Specify the interrupt lines for the ADV748x + +The device node must contain one 'port' child node per device input and output +port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes +are numbered as follows. + + Name Type Port + --------------------------------------- + AIN0 sink 0 + AIN1 sink 1 + AIN2 sink 2 + AIN3 sink 3 + AIN4 sink 4 + AIN5 sink 5 + AIN6 sink 6 + AIN7 sink 7 + HDMI sink 8 + TTL sink 9 + TXA source 10 + TXB source 11 + +The digital output port nodes must contain at least one endpoint. + +Ports are optional if they are not connected to anything at the hardware level. + +Example: + + video-receiver@70 { + compatible = "adi,adv7482"; + reg = <0x70>; + + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&gpio6>; + interrupt-names = "intrq1", "intrq2"; + interrupts = <30 IRQ_TYPE_LEVEL_LOW>, + <31 IRQ_TYPE_LEVEL_LOW>; + + port@7 { + reg = <7>; + + adv7482_ain7: endpoint { + remote-endpoint = <&cvbs_in>; + }; + }; + + port@8 { + reg = <8>; + + adv7482_hdmi: endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + + port@10 { + reg = <10>; + + adv7482_txa: endpoint { + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&csi40_in>; + }; + }; + + port@11 { + reg = <11>; + + adv7482_txb: endpoint { + clock-lanes = <0>; + data-lanes = <1>; + remote-endpoint = <&csi20_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt new file mode 100644 index 000000000000..b88dcdd41def --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt @@ -0,0 +1,9 @@ +Dongwoon Anatech DW9714 camera voice coil lens driver + +DW9174 is a 10-bit DAC with current sink capability. It is intended +for driving voice coil lenses in camera modules. + +Mandatory properties: + +- compatible: "dongwoon,dw9714" +- reg: I²C slave address diff --git a/Documentation/devicetree/bindings/media/meson-ao-cec.txt b/Documentation/devicetree/bindings/media/meson-ao-cec.txt new file mode 100644 index 000000000000..8671bdb08080 --- /dev/null +++ b/Documentation/devicetree/bindings/media/meson-ao-cec.txt @@ -0,0 +1,28 @@ +* Amlogic Meson AO-CEC driver + +The Amlogic Meson AO-CEC module is present is Amlogic SoCs and its purpose is +to handle communication between HDMI connected devices over the CEC bus. + +Required properties: + - compatible : value should be following + "amlogic,meson-gx-ao-cec" + + - reg : Physical base address of the IP registers and length of memory + mapped region. + + - interrupts : AO-CEC interrupt number to the CPU. + - clocks : from common clock binding: handle to AO-CEC clock. + - clock-names : from common clock binding: must contain "core", + corresponding to entry in the clocks property. + - hdmi-phandle: phandle to the HDMI controller + +Example: + +cec_AO: cec@100 { + compatible = "amlogic,meson-gx-ao-cec"; + reg = <0x0 0x00100 0x0 0x14>; + interrupts = <GIC_SPI 199 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc_AO CLKID_AO_CEC_32K>; + clock-names = "core"; + hdmi-phandle = <&hdmi_tx>; +}; diff --git a/Documentation/devicetree/bindings/media/mtk-cir.txt b/Documentation/devicetree/bindings/media/mtk-cir.txt index 2be2005577d6..5e18087ce11f 100644 --- a/Documentation/devicetree/bindings/media/mtk-cir.txt +++ b/Documentation/devicetree/bindings/media/mtk-cir.txt @@ -2,10 +2,14 @@ Device-Tree bindings for Mediatek consumer IR controller found in Mediatek SoC family Required properties: -- compatible : "mediatek,mt7623-cir" +- compatible : Should be + "mediatek,mt7623-cir": for MT7623 SoC + "mediatek,mt7622-cir": for MT7622 SoC - clocks : list of clock specifiers, corresponding to entries in clock-names property; -- clock-names : should contain "clk" entries; +- clock-names : should contain + - "clk" entries: for MT7623 SoC + - "clk", "bus" entries: for MT7622 SoC - interrupts : should contain IR IRQ number; - reg : should contain IO map address for IR. diff --git a/Documentation/devicetree/bindings/media/pxa-camera.txt b/Documentation/devicetree/bindings/media/pxa-camera.txt index 11f5b5d51af8..bc03ec096269 100644 --- a/Documentation/devicetree/bindings/media/pxa-camera.txt +++ b/Documentation/devicetree/bindings/media/pxa-camera.txt @@ -24,7 +24,6 @@ Example: clock-frequency = <50000000>; clock-output-names = "qci_mclk"; - status = "okay"; port { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/media/qcom,camss.txt b/Documentation/devicetree/bindings/media/qcom,camss.txt new file mode 100644 index 000000000000..cadecebc73f7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,camss.txt @@ -0,0 +1,197 @@ +Qualcomm Camera Subsystem + +* Properties + +- compatible: + Usage: required + Value type: <stringlist> + Definition: Should contain: + - "qcom,msm8916-camss" +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: Register ranges as listed in the reg-names property. +- reg-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the following entries: + - "csiphy0" + - "csiphy0_clk_mux" + - "csiphy1" + - "csiphy1_clk_mux" + - "csid0" + - "csid1" + - "ispif" + - "csi_clk_mux" + - "vfe0" +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: Interrupts as listed in the interrupt-names property. +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the following entries: + - "csiphy0" + - "csiphy1" + - "csid0" + - "csid1" + - "ispif" + - "vfe0" +- power-domains: + Usage: required + Value type: <prop-encoded-array> + Definition: A phandle and power domain specifier pairs to the + power domain which is responsible for collapsing + and restoring power to the peripheral. +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: A list of phandle and clock specifier pairs as listed + in clock-names property. +- clock-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the following entries: + - "camss_top_ahb" + - "ispif_ahb" + - "csiphy0_timer" + - "csiphy1_timer" + - "csi0_ahb" + - "csi0" + - "csi0_phy" + - "csi0_pix" + - "csi0_rdi" + - "csi1_ahb" + - "csi1" + - "csi1_phy" + - "csi1_pix" + - "csi1_rdi" + - "camss_ahb" + - "camss_vfe_vfe" + - "camss_csi_vfe" + - "iface" + - "bus" +- vdda-supply: + Usage: required + Value type: <phandle> + Definition: A phandle to voltage supply for CSI2. +- iommus: + Usage: required + Value type: <prop-encoded-array> + Definition: A list of phandle and IOMMU specifier pairs. + +* Nodes + +- ports: + Usage: required + Definition: As described in video-interfaces.txt in same directory. + Properties: + - reg: + Usage: required + Value type: <u32> + Definition: Selects CSI2 PHY interface - PHY0 or PHY1. + Endpoint node properties: + - clock-lanes: + Usage: required + Value type: <u32> + Definition: The physical clock lane index. The value + must always be <1> as the physical clock + lane is lane 1. + - data-lanes: + Usage: required + Value type: <prop-encoded-array> + Definition: An array of physical data lanes indexes. + Position of an entry determines the logical + lane number, while the value of an entry + indicates physical lane index. Lane swapping + is supported. + +* An Example + + camss: camss@1b00000 { + compatible = "qcom,msm8916-camss"; + reg = <0x1b0ac00 0x200>, + <0x1b00030 0x4>, + <0x1b0b000 0x200>, + <0x1b00038 0x4>, + <0x1b08000 0x100>, + <0x1b08400 0x100>, + <0x1b0a000 0x500>, + <0x1b00020 0x10>, + <0x1b10000 0x1000>; + reg-names = "csiphy0", + "csiphy0_clk_mux", + "csiphy1", + "csiphy1_clk_mux", + "csid0", + "csid1", + "ispif", + "csi_clk_mux", + "vfe0"; + interrupts = <GIC_SPI 78 0>, + <GIC_SPI 79 0>, + <GIC_SPI 51 0>, + <GIC_SPI 52 0>, + <GIC_SPI 55 0>, + <GIC_SPI 57 0>; + interrupt-names = "csiphy0", + "csiphy1", + "csid0", + "csid1", + "ispif", + "vfe0"; + power-domains = <&gcc VFE_GDSC>; + clocks = <&gcc GCC_CAMSS_TOP_AHB_CLK>, + <&gcc GCC_CAMSS_ISPIF_AHB_CLK>, + <&gcc GCC_CAMSS_CSI0PHYTIMER_CLK>, + <&gcc GCC_CAMSS_CSI1PHYTIMER_CLK>, + <&gcc GCC_CAMSS_CSI0_AHB_CLK>, + <&gcc GCC_CAMSS_CSI0_CLK>, + <&gcc GCC_CAMSS_CSI0PHY_CLK>, + <&gcc GCC_CAMSS_CSI0PIX_CLK>, + <&gcc GCC_CAMSS_CSI0RDI_CLK>, + <&gcc GCC_CAMSS_CSI1_AHB_CLK>, + <&gcc GCC_CAMSS_CSI1_CLK>, + <&gcc GCC_CAMSS_CSI1PHY_CLK>, + <&gcc GCC_CAMSS_CSI1PIX_CLK>, + <&gcc GCC_CAMSS_CSI1RDI_CLK>, + <&gcc GCC_CAMSS_AHB_CLK>, + <&gcc GCC_CAMSS_VFE0_CLK>, + <&gcc GCC_CAMSS_CSI_VFE0_CLK>, + <&gcc GCC_CAMSS_VFE_AHB_CLK>, + <&gcc GCC_CAMSS_VFE_AXI_CLK>; + clock-names = "camss_top_ahb", + "ispif_ahb", + "csiphy0_timer", + "csiphy1_timer", + "csi0_ahb", + "csi0", + "csi0_phy", + "csi0_pix", + "csi0_rdi", + "csi1_ahb", + "csi1", + "csi1_phy", + "csi1_pix", + "csi1_rdi", + "camss_ahb", + "camss_vfe_vfe", + "camss_csi_vfe", + "iface", + "bus"; + vdda-supply = <&pm8916_l2>; + iommus = <&apps_iommu 3>; + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + csiphy0_ep: endpoint { + clock-lanes = <1>; + data-lanes = <0 2>; + remote-endpoint = <&ov5645_ep>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,drif.txt b/Documentation/devicetree/bindings/media/renesas,drif.txt index 39516b94c28f..0d8974aa8b38 100644 --- a/Documentation/devicetree/bindings/media/renesas,drif.txt +++ b/Documentation/devicetree/bindings/media/renesas,drif.txt @@ -40,6 +40,7 @@ To summarize, Required properties of an internal channel: ------------------------------------------- - compatible: "renesas,r8a7795-drif" if DRIF controller is a part of R8A7795 SoC. + "renesas,r8a7796-drif" if DRIF controller is a part of R8A7796 SoC. "renesas,rcar-gen3-drif" for a generic R-Car Gen3 compatible device. When compatible with the generic version, nodes must list the diff --git a/Documentation/devicetree/bindings/media/s5p-cec.txt b/Documentation/devicetree/bindings/media/s5p-cec.txt index 1b1a10ba48ce..6f3756da900f 100644 --- a/Documentation/devicetree/bindings/media/s5p-cec.txt +++ b/Documentation/devicetree/bindings/media/s5p-cec.txt @@ -33,5 +33,4 @@ hdmicec: cec@100B0000 { hdmi-phandle = <&hdmi>; pinctrl-names = "default"; pinctrl-0 = <&hdmi_cec>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/media/samsung-fimc.txt b/Documentation/devicetree/bindings/media/samsung-fimc.txt index 922d6f8e74be..e4e15d8d7521 100644 --- a/Documentation/devicetree/bindings/media/samsung-fimc.txt +++ b/Documentation/devicetree/bindings/media/samsung-fimc.txt @@ -166,7 +166,6 @@ Example: clock-output-names = "cam_a_clkout", "cam_b_clkout"; pinctrl-names = "default"; pinctrl-0 = <&cam_port_a_clk_active>; - status = "okay"; #address-cells = <1>; #size-cells = <1>; @@ -189,7 +188,6 @@ Example: compatible = "samsung,exynos4210-fimc"; reg = <0x11800000 0x1000>; interrupts = <0 85 0>; - status = "okay"; }; csis_0: csis@11880000 { diff --git a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt index cc51b1fd6e0c..6af3fc210ecc 100644 --- a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt +++ b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt @@ -52,7 +52,6 @@ Example: c8sectpfe@08a20000 { compatible = "st,stih407-c8sectpfe"; - status = "okay"; reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>; reg-names = "stfe", "stfe-ram"; interrupts = <GIC_SPI 34 IRQ_TYPE_NONE>, <GIC_SPI 35 IRQ_TYPE_NONE>; diff --git a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt index df7182a63e59..e47c7ccc57f1 100644 --- a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt +++ b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt @@ -59,7 +59,6 @@ I2C-connected TVP5147 decoder: tvp5147@5d { compatible = "ti,tvp5147"; reg = <0x5d>; - status = "okay"; port { composite_in: endpoint { diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt index 9cd2a369125d..852041a7480c 100644 --- a/Documentation/devicetree/bindings/media/video-interfaces.txt +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt @@ -76,6 +76,11 @@ Optional endpoint properties mode horizontal and vertical synchronization signals are provided to the slave device (data source) by the master device (data sink). In the master mode the data source device is also the source of the synchronization signals. +- bus-type: data bus type. Possible values are: + 0 - autodetect based on other properties (MIPI CSI-2 D-PHY, parallel or Bt656) + 1 - MIPI CSI-2 C-PHY + 2 - MIPI CSI1 + 3 - CCP2 - bus-width: number of data lines actively used, valid for the parallel busses. - data-shift: on the parallel data busses, if bus-width is used to specify the number of data lines, data-shift can be used to specify which data lines are @@ -112,7 +117,8 @@ Optional endpoint properties should be the combined length of data-lanes and clock-lanes properties. If the lane-polarities property is omitted, the value must be interpreted as 0 (normal). This property is valid for serial busses only. - +- strobe: Whether the clock signal is used as clock (0) or strobe (1). Used + with CCP2, for instance. Example ------- diff --git a/Documentation/devicetree/bindings/media/zx-irdec.txt b/Documentation/devicetree/bindings/media/zx-irdec.txt new file mode 100644 index 000000000000..295b9fab593e --- /dev/null +++ b/Documentation/devicetree/bindings/media/zx-irdec.txt @@ -0,0 +1,14 @@ +IR Decoder (IRDEC) on ZTE ZX family SoCs + +Required properties: + - compatible: Should be "zte,zx296718-irdec". + - reg: Physical base address and length of IRDEC registers. + - interrupts: Interrupt number of IRDEC. + +Exmaples: + + irdec: ir-decoder@111000 { + compatible = "zte,zx296718-irdec"; + reg = <0x111000 0x1000>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt index 21277a56e94c..ddf46b8856a5 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt @@ -15,6 +15,9 @@ Required properties: the register. - "smi" : It's the clock for transfer data and command. +Required property for mt2701: +- mediatek,larb-id :the hardware id of this larb. + Example: larb1: larb@16010000 { compatible = "mediatek,mt8173-smi-larb"; @@ -25,3 +28,15 @@ Example: <&vdecsys CLK_VDEC_LARB_CKEN>; clock-names = "apb", "smi"; }; + +Example for mt2701: + larb0: larb@14010000 { + compatible = "mediatek,mt2701-smi-larb"; + reg = <0 0x14010000 0 0x1000>; + mediatek,smi = <&smi_common>; + mediatek,larb-id = <0>; + clocks = <&mmsys CLK_MM_SMI_LARB0>, + <&mmsys CLK_MM_SMI_LARB0>; + clock-names = "apb", "smi"; + power-domains = <&scpsys MT2701_POWER_DOMAIN_DISP>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt index 1ee3bc09f319..8b9388cc1ccc 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt @@ -130,7 +130,6 @@ The reg property implicitly specifies the chip select as this: Example: devbus-bootcs@d0010400 { - status = "okay"; ranges = <0 0xf0000000 0x1000000>; /* @addr 0xf0000000, size 0x1000000 */ #address-cells = <1>; #size-cells = <1>; diff --git a/Documentation/devicetree/bindings/mfd/act8945a.txt b/Documentation/devicetree/bindings/mfd/act8945a.txt index 462819ac3da8..e6f168db6c72 100644 --- a/Documentation/devicetree/bindings/mfd/act8945a.txt +++ b/Documentation/devicetree/bindings/mfd/act8945a.txt @@ -12,7 +12,6 @@ Example: pmic@5b { compatible = "active-semi,act8945a"; reg = <0x5b>; - status = "okay"; active-semi,vsel-high; @@ -79,6 +78,5 @@ Example: active-semi,input-voltage-threshold-microvolt = <6600>; active-semi,precondition-timeout = <40>; active-semi,total-timeout = <3>; - status = "okay"; }; }; diff --git a/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt index eec40be7f79a..3f643ef121ff 100644 --- a/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt +++ b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt @@ -25,7 +25,6 @@ Example: clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; clock-names = "periph_clk","sys_clk", "slow_clk"; interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>; - status = "disabled"; hlcdc-display-controller { compatible = "atmel,hlcdc-display-controller"; diff --git a/Documentation/devicetree/bindings/mfd/atmel-smc.txt b/Documentation/devicetree/bindings/mfd/atmel-smc.txt index 26eeed373934..1103ce2030fb 100644 --- a/Documentation/devicetree/bindings/mfd/atmel-smc.txt +++ b/Documentation/devicetree/bindings/mfd/atmel-smc.txt @@ -8,6 +8,7 @@ Required properties: - compatible: Should be one of the following "atmel,at91sam9260-smc", "syscon" "atmel,sama5d3-smc", "syscon" + "atmel,sama5d2-smc", "syscon" - reg: Contains offset/length value of the SMC memory region. diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt index aca09af66514..9455503b0299 100644 --- a/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -7,7 +7,14 @@ axp209 (X-Powers) axp221 (X-Powers) axp223 (X-Powers) axp803 (X-Powers) +axp806 (X-Powers) axp809 (X-Powers) +axp813 (X-Powers) + +The AXP813 is 2 chips packaged into 1. The 2 chips do not share anything +other than the packaging. Pins are routed separately. As such they should +be treated as separate entities. The other half is an AC100 RTC/codec +combo chip. Please see ./ac100.txt for its bindings. Required properties: - compatible: should be one of: @@ -19,6 +26,7 @@ Required properties: * "x-powers,axp803" * "x-powers,axp806" * "x-powers,axp809" + * "x-powers,axp813" - reg: The I2C slave address or RSB hardware address for the AXP chip - interrupt-parent: The parent interrupt controller - interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin @@ -28,12 +36,14 @@ Required properties: Optional properties: - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz AXP152/20X: range: 750-1875, Default: 1.5 MHz - AXP22X/80X: range: 1800-4050, Default: 3 MHz + AXP22X/8XX: range: 1800-4050, Default: 3 MHz -- x-powers,drive-vbus-en: axp221 / axp223 only boolean, set this when the - N_VBUSEN pin is used as an output pin to control an external - regulator to drive the OTG VBus, rather then as an input pin - which signals whether the board is driving OTG VBus or not. +- x-powers,drive-vbus-en: boolean, set this when the N_VBUSEN pin is + used as an output pin to control an external + regulator to drive the OTG VBus, rather then + as an input pin which signals whether the + board is driving OTG VBus or not. + (axp221 / axp223 / axp813 only) - x-powers,master-mode: Boolean (axp806 only). Set this when the PMIC is wired for master mode. The default is slave mode. @@ -171,6 +181,36 @@ LDO_IO1 : LDO : ips-supply : GPIO 1 RTC_LDO : LDO : ips-supply : always on SW : On/Off Switch : swin-supply +AXP813 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDC1 : DC-DC buck : vin1-supply +DCDC2 : DC-DC buck : vin2-supply : poly-phase capable +DCDC3 : DC-DC buck : vin3-supply : poly-phase capable +DCDC4 : DC-DC buck : vin4-supply +DCDC5 : DC-DC buck : vin5-supply : poly-phase capable +DCDC6 : DC-DC buck : vin6-supply : poly-phase capable +DCDC7 : DC-DC buck : vin7-supply +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +DLDO1 : LDO : dldoin-supply : shared supply +DLDO2 : LDO : dldoin-supply : shared supply +DLDO3 : LDO : dldoin-supply : shared supply +DLDO4 : LDO : dldoin-supply : shared supply +ELDO1 : LDO : eldoin-supply : shared supply +ELDO2 : LDO : eldoin-supply : shared supply +ELDO3 : LDO : eldoin-supply : shared supply +FLDO1 : LDO : fldoin-supply : shared supply +FLDO2 : LDO : fldoin-supply : shared supply +FLDO3 : LDO : fldoin-supply : shared supply +LDO_IO0 : LDO : ips-supply : GPIO 0 +LDO_IO1 : LDO : ips-supply : GPIO 1 +RTC_LDO : LDO : ips-supply : always on +SW : On/Off Switch : swin-supply +DRIVEVBUS : Enable output : drivevbus-supply : external regulator + Example: axp209: pmic@34 { diff --git a/Documentation/devicetree/bindings/mfd/bd9571mwv.txt b/Documentation/devicetree/bindings/mfd/bd9571mwv.txt new file mode 100644 index 000000000000..9ab216a851d5 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/bd9571mwv.txt @@ -0,0 +1,49 @@ +* ROHM BD9571MWV Power Management Integrated Circuit (PMIC) bindings + +Required properties: + - compatible : Should be "rohm,bd9571mwv". + - reg : I2C slave address. + - interrupt-parent : Phandle to the parent interrupt controller. + - interrupts : The interrupt line the device is connected to. + - interrupt-controller : Marks the device node as an interrupt controller. + - #interrupt-cells : The number of cells to describe an IRQ, should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as trigger + masks from ../interrupt-controller/interrupts.txt. + - gpio-controller : Marks the device node as a GPIO Controller. + - #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - regulators: : List of child nodes that specify the regulator + initialization data. Child nodes must be named + after their hardware counterparts: + - vd09 + - vd18 + - vd25 + - vd33 + - dvfs + Each child node is defined using the standard + binding for regulators. + +Example: + + pmic: pmic@30 { + compatible = "rohm,bd9571mwv"; + reg = <0x30>; + interrupt-parent = <&gpio2>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + + regulators { + dvfs: dvfs { + regulator-name = "dvfs"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1030000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt index 9554292dc6cb..07c69c0c6624 100644 --- a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt +++ b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt @@ -4,6 +4,14 @@ Required properties: - compatible : Should be "dlg,da9052", "dlg,da9053-aa", "dlg,da9053-ab", or "dlg,da9053-bb" +Optional properties: +- dlg,tsi-as-adc : Boolean, if set the X+, X-, Y+, Y- touchscreen + input lines are used as general purpose analogue + input. +- tsiref-supply: Phandle to the regulator, which provides the reference + voltage for the TSIREF pin. Must be provided when the + touchscreen pins are used for ADC purposes. + Sub-nodes: - regulators : Contain the regulator nodes. The DA9052/53 regulators are bound using their names as listed below: @@ -29,7 +37,6 @@ Sub-nodes: Examples: i2c@63fc8000 { /* I2C1 */ - status = "okay"; pmic: dialog@48 { compatible = "dlg,da9053-aa"; diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt index 8aba48821a85..39ba4146769d 100644 --- a/Documentation/devicetree/bindings/mfd/mc13xxx.txt +++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt @@ -116,7 +116,6 @@ ecspi@70010000 { /* ECSPI1 */ fsl,spi-num-chipselects = <2>; cs-gpios = <&gpio4 24 0>, /* GPIO4_24 */ <&gpio4 25 0>; /* GPIO4_25 */ - status = "okay"; pmic: mc13892@0 { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/mfd/mxs-lradc.txt b/Documentation/devicetree/bindings/mfd/mxs-lradc.txt index 555fb117d4fa..755cbef0647d 100644 --- a/Documentation/devicetree/bindings/mfd/mxs-lradc.txt +++ b/Documentation/devicetree/bindings/mfd/mxs-lradc.txt @@ -26,7 +26,6 @@ Example for i.MX23 SoC: compatible = "fsl,imx23-lradc"; reg = <0x80050000 0x2000>; interrupts = <36 37 38 39 40 41 42 43 44>; - status = "okay"; fsl,lradc-touchscreen-wires = <4>; fsl,ave-ctrl = <4>; fsl,ave-delay = <2>; @@ -39,7 +38,6 @@ Example for i.MX28 SoC: compatible = "fsl,imx28-lradc"; reg = <0x80050000 0x2000>; interrupts = <10 14 15 16 17 18 19 20 21 22 23 24 25>; - status = "okay"; fsl,lradc-touchscreen-wires = <5>; fsl,ave-ctrl = <4>; fsl,ave-delay = <2>; diff --git a/Documentation/devicetree/bindings/mfd/retu.txt b/Documentation/devicetree/bindings/mfd/retu.txt new file mode 100644 index 000000000000..876242394a16 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/retu.txt @@ -0,0 +1,25 @@ +* Device tree bindings for Nokia Retu and Tahvo multi-function device + +Retu and Tahvo are a multi-function devices found on Nokia Internet +Tablets (770, N800 and N810). The Retu chip provides watchdog timer +and power button control functionalities while Tahvo chip provides +USB transceiver functionality. + +Required properties: +- compatible: "nokia,retu" or "nokia,tahvo" +- reg: Specifies the CBUS slave address of the ASIC chip +- interrupts: The interrupt line the device is connected to +- interrupt-parent: The parent interrupt controller + +Example: + +cbus0 { + compatible = "i2c-cbus-gpio"; + ... + retu: retu@1 { + compatible = "nokia,retu"; + interrupt-parent = <&gpio4>; + interrupts = <12 IRQ_TYPE_EDGE_RISING>; + reg = <0x1>; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt index 9636ae8d8d41..91b65227afeb 100644 --- a/Documentation/devicetree/bindings/mfd/rk808.txt +++ b/Documentation/devicetree/bindings/mfd/rk808.txt @@ -1,11 +1,14 @@ RK8XX Power Management Integrated Circuit The rk8xx family current members: +rk805 rk808 rk818 Required properties: -- compatible: "rockchip,rk808", "rockchip,rk818" +- compatible: "rockchip,rk805" +- compatible: "rockchip,rk808" +- compatible: "rockchip,rk818" - reg: I2C slave address - interrupt-parent: The parent interrupt controller. - interrupts: the interrupt outputs of the controller. @@ -18,6 +21,14 @@ Optional properties: - rockchip,system-power-controller: Telling whether or not this pmic is controlling the system power. +Optional RK805 properties: +- vcc1-supply: The input supply for DCDC_REG1 +- vcc2-supply: The input supply for DCDC_REG2 +- vcc3-supply: The input supply for DCDC_REG3 +- vcc4-supply: The input supply for DCDC_REG4 +- vcc5-supply: The input supply for LDO_REG1 and LDO_REG2 +- vcc6-supply: The input supply for LDO_REG3 + Optional RK808 properties: - vcc1-supply: The input supply for DCDC_REG1 - vcc2-supply: The input supply for DCDC_REG2 @@ -56,6 +67,15 @@ by a child node of the 'regulators' node. /* standard regulator bindings here */ }; +Following regulators of the RK805 PMIC regulators are supported. Note that +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO +number as described in RK805 datasheet. + + - DCDC_REGn + - valid values for n are 1 to 4. + - LDO_REGn + - valid values for n are 1 to 3 + Following regulators of the RK808 PMIC block are supported. Note that the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO number as described in RK808 datasheet. diff --git a/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt b/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt index df664018c148..d759da606f75 100644 --- a/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt +++ b/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt @@ -57,7 +57,6 @@ audio-subsystem { clock-names = "iis", "i2s_opclk0", "i2s_opclk1"; pinctrl-names = "default"; pinctrl-0 = <&i2s0_bus>; - status = "disabled"; }; serial_3: serial@11460000 { @@ -69,6 +68,5 @@ audio-subsystem { clock-names = "uart", "clk_uart_baud0"; pinctrl-names = "default"; pinctrl-0 = <&uart_aud_bus>; - status = "disabled"; }; }; diff --git a/Documentation/devicetree/bindings/mfd/stm32-lptimer.txt b/Documentation/devicetree/bindings/mfd/stm32-lptimer.txt new file mode 100644 index 000000000000..2a9ff29db9c9 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/stm32-lptimer.txt @@ -0,0 +1,48 @@ +STMicroelectronics STM32 Low-Power Timer + +The STM32 Low-Power Timer (LPTIM) is a 16-bit timer that provides several +functions: +- PWM output (with programmable prescaler, configurable polarity) +- Quadrature encoder, counter +- Trigger source for STM32 ADC/DAC (LPTIM_OUT) + +Required properties: +- compatible: Must be "st,stm32-lptimer". +- reg: Offset and length of the device's register set. +- clocks: Phandle to the clock used by the LP Timer module. +- clock-names: Must be "mux". +- #address-cells: Should be '<1>'. +- #size-cells: Should be '<0>'. + +Optional subnodes: +- pwm: See ../pwm/pwm-stm32-lp.txt +- counter: See ../iio/timer/stm32-lptimer-cnt.txt +- trigger: See ../iio/timer/stm32-lptimer-trigger.txt + +Example: + + timer@40002400 { + compatible = "st,stm32-lptimer"; + reg = <0x40002400 0x400>; + clocks = <&timer_clk>; + clock-names = "mux"; + #address-cells = <1>; + #size-cells = <0>; + + pwm { + compatible = "st,stm32-pwm-lp"; + pinctrl-names = "default"; + pinctrl-0 = <&lppwm1_pins>; + }; + + trigger@0 { + compatible = "st,stm32-lptimer-trigger"; + reg = <0>; + }; + + counter { + compatible = "st,stm32-lptimer-counter"; + pinctrl-names = "default"; + pinctrl-0 = <&lptim1_in_pins>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/tps6105x.txt b/Documentation/devicetree/bindings/mfd/tps6105x.txt new file mode 100644 index 000000000000..93602c7a19c8 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tps6105x.txt @@ -0,0 +1,17 @@ +* Device tree bindings for TI TPS61050/61052 Boost Converters + +The TP61050/TPS61052 is a high-power "white LED driver". The +device provides LED, GPIO and regulator functionalities. + +Required properties: +- compatible: "ti,tps61050" or "ti,tps61052" +- reg: Specifies the I2C slave address + +Example: + +i2c0 { + tps61052@33 { + compatible = "ti,tps61052"; + reg = <0x33>; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/wm831x.txt b/Documentation/devicetree/bindings/mfd/wm831x.txt index 9f8b7430673c..505709403d3f 100644 --- a/Documentation/devicetree/bindings/mfd/wm831x.txt +++ b/Documentation/devicetree/bindings/mfd/wm831x.txt @@ -31,6 +31,7 @@ Required properties: ../interrupt-controller/interrupts.txt Optional sub-nodes: + - phys : Contains a phandle to the USB PHY. - regulators : Contains sub-nodes for each of the regulators supplied by the device. The regulators are bound using their names listed below: diff --git a/Documentation/devicetree/bindings/mfd/zii,rave-sp.txt b/Documentation/devicetree/bindings/mfd/zii,rave-sp.txt new file mode 100644 index 000000000000..088eff9ddb78 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/zii,rave-sp.txt @@ -0,0 +1,39 @@ +Zodiac Inflight Innovations RAVE Supervisory Processor + +RAVE Supervisory Processor communicates with SoC over UART. It is +expected that its Device Tree node is specified as a child of a node +corresponding to UART controller used for communication. + +Required parent device properties: + + - compatible: Should be one of: + - "zii,rave-sp-niu" + - "zii,rave-sp-mezz" + - "zii,rave-sp-esb" + - "zii,rave-sp-rdu1" + - "zii,rave-sp-rdu2" + + - current-speed: Should be set to baud rate SP device is using + +RAVE SP consists of the following sub-devices: + +Device Description +------ ----------- +rave-sp-wdt : Watchdog +rave-sp-nvmem : Interface to onborad EEPROM +rave-sp-backlight : Display backlight +rave-sp-hwmon : Interface to onboard hardware sensors +rave-sp-leds : Interface to onboard LEDs +rave-sp-input : Interface to onboard power button + +Example of usage: + + rdu { + compatible = "zii,rave-sp-rdu2"; + current-speed = <1000000>; + + watchdog { + compatible = "zii,rave-sp-watchdog"; + }; + }; + diff --git a/Documentation/devicetree/bindings/mips/lantiq/fpi-bus.txt b/Documentation/devicetree/bindings/mips/lantiq/fpi-bus.txt new file mode 100644 index 000000000000..0a2df4338332 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/lantiq/fpi-bus.txt @@ -0,0 +1,31 @@ +Lantiq XWAY SoC FPI BUS binding +============================ + + +------------------------------------------------------------------------------- +Required properties: +- compatible : Should be one of + "lantiq,xrx200-fpi" +- reg : The address and length of the XBAR + configuration register. + Address and length of the FPI bus itself. +- lantiq,rcu : A phandle to the RCU syscon +- lantiq,offset-endianness : Offset of the endianness configuration + register + +------------------------------------------------------------------------------- +Example for the FPI on the xrx200 SoCs: + fpi@10000000 { + compatible = "lantiq,xrx200-fpi"; + ranges = <0x0 0x10000000 0xf000000>; + reg = <0x1f400000 0x1000>, + <0x10000000 0xf000000>; + lantiq,rcu = <&rcu0>; + lantiq,offset-endianness = <0x4c>; + #address-cells = <1>; + #size-cells = <1>; + + gptu@e100a00 { + ...... + }; + }; diff --git a/Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt b/Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt new file mode 100644 index 000000000000..a0c19bd1ce66 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt @@ -0,0 +1,36 @@ +Lantiq XWAY SoC GPHY binding +============================ + +This binding describes a software-defined ethernet PHY, provided by the RCU +module on newer Lantiq XWAY SoCs (xRX200 and newer). + +------------------------------------------------------------------------------- +Required properties: +- compatible : Should be one of + "lantiq,xrx200a1x-gphy" + "lantiq,xrx200a2x-gphy" + "lantiq,xrx300-gphy" + "lantiq,xrx330-gphy" +- reg : Addrress of the GPHY FW load address register +- resets : Must reference the RCU GPHY reset bit +- reset-names : One entry, value must be "gphy" or optional "gphy2" +- clocks : A reference to the (PMU) GPHY clock gate + +Optional properties: +- lantiq,gphy-mode : GPHY_MODE_GE (default) or GPHY_MODE_FE as defined in + <dt-bindings/mips/lantiq_xway_gphy.h> + + +------------------------------------------------------------------------------- +Example for the GPHys on the xRX200 SoCs: + +#include <dt-bindings/mips/lantiq_rcu_gphy.h> + gphy0: gphy@20 { + compatible = "lantiq,xrx200a2x-gphy"; + reg = <0x20 0x4>; + + resets = <&reset0 31 30>, <&reset1 7 7>; + reset-names = "gphy", "gphy2"; + clocks = <&pmu0 XRX200_PMU_GATE_GPHY>; + lantiq,gphy-mode = <GPHY_MODE_GE>; + }; diff --git a/Documentation/devicetree/bindings/mips/lantiq/rcu.txt b/Documentation/devicetree/bindings/mips/lantiq/rcu.txt new file mode 100644 index 000000000000..a086f1e1cdd7 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/lantiq/rcu.txt @@ -0,0 +1,89 @@ +Lantiq XWAY SoC RCU binding +=========================== + +This binding describes the RCU (reset controller unit) multifunction device, +where each sub-device has it's own set of registers. + +The RCU register range is used for multiple purposes. Mostly one device +uses one or multiple register exclusively, but for some registers some +bits are for one driver and some other bits are for a different driver. +With this patch all accesses to the RCU registers will go through +syscon. + + +------------------------------------------------------------------------------- +Required properties: +- compatible : The first and second values must be: + "lantiq,xrx200-rcu", "simple-mfd", "syscon" +- reg : The address and length of the system control registers + + +------------------------------------------------------------------------------- +Example of the RCU bindings on a xRX200 SoC: + rcu0: rcu@203000 { + compatible = "lantiq,xrx200-rcu", "simple-mfd", "syscon"; + reg = <0x203000 0x100>; + ranges = <0x0 0x203000 0x100>; + big-endian; + + gphy0: gphy@20 { + compatible = "lantiq,xrx200a2x-gphy"; + reg = <0x20 0x4>; + + resets = <&reset0 31 30>, <&reset1 7 7>; + reset-names = "gphy", "gphy2"; + lantiq,gphy-mode = <GPHY_MODE_GE>; + }; + + gphy1: gphy@68 { + compatible = "lantiq,xrx200a2x-gphy"; + reg = <0x68 0x4>; + + resets = <&reset0 29 28>, <&reset1 6 6>; + reset-names = "gphy", "gphy2"; + lantiq,gphy-mode = <GPHY_MODE_GE>; + }; + + reset0: reset-controller@10 { + compatible = "lantiq,xrx200-reset"; + reg = <0x10 4>, <0x14 4>; + + #reset-cells = <2>; + }; + + reset1: reset-controller@48 { + compatible = "lantiq,xrx200-reset"; + reg = <0x48 4>, <0x24 4>; + + #reset-cells = <2>; + }; + + usb_phy0: usb2-phy@18 { + compatible = "lantiq,xrx200-usb2-phy"; + reg = <0x18 4>, <0x38 4>; + status = "disabled"; + + resets = <&reset1 4 4>, <&reset0 4 4>; + reset-names = "phy", "ctrl"; + #phy-cells = <0>; + }; + + usb_phy1: usb2-phy@34 { + compatible = "lantiq,xrx200-usb2-phy"; + reg = <0x34 4>, <0x3C 4>; + status = "disabled"; + + resets = <&reset1 5 4>, <&reset0 4 4>; + reset-names = "phy", "ctrl"; + #phy-cells = <0>; + }; + + reboot@10 { + compatible = "syscon-reboot"; + reg = <0x10 4>; + + regmap = <&rcu0>; + offset = <0x10>; + mask = <0x40000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/mips/ni.txt b/Documentation/devicetree/bindings/mips/ni.txt new file mode 100644 index 000000000000..722bf2d62da9 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/ni.txt @@ -0,0 +1,7 @@ +National Instruments MIPS platforms + +required root node properties: + - compatible: must be "ni,169445" + +CPU Nodes + - compatible: must be "mti,mips14KEc" diff --git a/Documentation/devicetree/bindings/mips/ralink.txt b/Documentation/devicetree/bindings/mips/ralink.txt index b35a8d04f8b6..a16e8d7fe56c 100644 --- a/Documentation/devicetree/bindings/mips/ralink.txt +++ b/Documentation/devicetree/bindings/mips/ralink.txt @@ -15,3 +15,4 @@ value must be one of the following values: ralink,rt5350-soc ralink,mt7620a-soc ralink,mt7620n-soc + ralink,mt7628a-soc diff --git a/Documentation/devicetree/bindings/misc/atmel-ssc.txt b/Documentation/devicetree/bindings/misc/atmel-ssc.txt index f8629bb73945..f9fb412642fe 100644 --- a/Documentation/devicetree/bindings/misc/atmel-ssc.txt +++ b/Documentation/devicetree/bindings/misc/atmel-ssc.txt @@ -47,5 +47,4 @@ ssc0: ssc@f0010000 { dma-names = "tx", "rx"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt index 49df630bd44f..60481bfc3d31 100644 --- a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt @@ -74,5 +74,4 @@ Example: phys = <&emmc_phy>; phy-names = "phy_arasan"; #clock-cells = <0>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/mmc/davinci_mmc.txt b/Documentation/devicetree/bindings/mmc/davinci_mmc.txt index e5a0140b2381..516fb0143d4c 100644 --- a/Documentation/devicetree/bindings/mmc/davinci_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/davinci_mmc.txt @@ -24,7 +24,6 @@ mmc0: mmc@1c40000 { compatible = "ti,da830-mmc", reg = <0x40000 0x1000>; interrupts = <16>; - status = "okay"; bus-width = <4>; max-frequency = <50000000>; dmas = <&edma 16 diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.txt index db442355cd24..184ccffe2739 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.txt @@ -20,5 +20,4 @@ sdhci1: sdhci@10014000 { dma-names = "rx-tx"; bus-width = <4>; cd-gpios = <&gpio3 29>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/mmc/mmc-card.txt b/Documentation/devicetree/bindings/mmc/mmc-card.txt index a70fcd65b9ea..8d2d71758907 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-card.txt +++ b/Documentation/devicetree/bindings/mmc/mmc-card.txt @@ -21,7 +21,6 @@ Example: vmmc-supply = <®_vcc3v3>; bus-width = <8>; non-removable; - status = "okay"; mmccard: mmccard@0 { reg = <0>; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index c7f4a0ec48ed..b32ade645ad9 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -153,7 +153,6 @@ mmc3: mmc@01c12000 { bus-width = <4>; non-removable; mmc-pwrseq = <&sdhci0_pwrseq> - status = "okay"; brcmf: bcrmf@1 { reg = <1>; diff --git a/Documentation/devicetree/bindings/mmc/orion-sdio.txt b/Documentation/devicetree/bindings/mmc/orion-sdio.txt index 84f0ebd67a13..10f0818a34c5 100644 --- a/Documentation/devicetree/bindings/mmc/orion-sdio.txt +++ b/Documentation/devicetree/bindings/mmc/orion-sdio.txt @@ -13,5 +13,4 @@ Example: reg = <0xd00d4000 0x200>; interrupts = <54>; clocks = <&gateclk 17>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt index c32dc5a9dbe6..5ff1e12c655a 100644 --- a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt +++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt @@ -11,6 +11,8 @@ Required properties: - "renesas,mmcif-r7s72100" for the MMCIF found in r7s72100 SoCs - "renesas,mmcif-r8a73a4" for the MMCIF found in r8a73a4 SoCs - "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs + - "renesas,mmcif-r8a7743" for the MMCIF found in r8a7743 SoCs + - "renesas,mmcif-r8a7745" for the MMCIF found in r8a7745 SoCs - "renesas,mmcif-r8a7778" for the MMCIF found in r8a7778 SoCs - "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs - "renesas,mmcif-r8a7791" for the MMCIF found in r8a7791 SoCs @@ -21,7 +23,7 @@ Required properties: - interrupts: Some SoCs have only 1 shared interrupt, while others have either 2 or 3 individual interrupts (error, int, card detect). Below is the number of interrupts for each SoC: - 1: r8a73a4, r8a7778, r8a7790, r8a7791, r8a7793, r8a7794 + 1: r8a73a4, r8a7743, r8a7745, r8a7778, r8a7790, r8a7791, r8a7793, r8a7794 2: r8a7740, sh73a0 3: r7s72100 diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index 49ed3ad2524a..c6558785e61b 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -15,6 +15,7 @@ Required Properties: - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 - "rockchip,rv1108-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RV1108 - "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3036 + - "rockchip,rk3228-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK322x - "rockchip,rk3328-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3328 - "rockchip,rk3368-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3368 - "rockchip,rk3399-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3399 diff --git a/Documentation/devicetree/bindings/mmc/sdhci-st.txt b/Documentation/devicetree/bindings/mmc/sdhci-st.txt index 230fd696eb92..e35645598315 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-st.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-st.txt @@ -63,7 +63,6 @@ Example: mmc0: sdhci@fe81e000 { compatible = "st,sdhci"; - status = "disabled"; reg = <0xfe81e000 0x1000>; interrupts = <GIC_SPI 127 IRQ_TYPE_NONE>; interrupt-names = "mmcirq"; @@ -77,7 +76,6 @@ mmc0: sdhci@fe81e000 { mmc1: sdhci@09080000 { compatible = "st,sdhci-stih407", "st,sdhci"; - status = "disabled"; reg = <0x09080000 0x7ff>; reg-names = "mmc"; interrupts = <GIC_SPI 90 IRQ_TYPE_NONE>; @@ -94,7 +92,6 @@ mmc1: sdhci@09080000 { mmc0: sdhci@09060000 { compatible = "st,sdhci-stih407", "st,sdhci"; - status = "disabled"; reg = <0x09060000 0x7ff>, <0x9061008 0x20>; reg-names = "mmc", "top-mmc-delay"; interrupts = <GIC_SPI 92 IRQ_TYPE_NONE>; diff --git a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt index 7d53a799f140..63b57e2a10fb 100644 --- a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt +++ b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt @@ -12,6 +12,7 @@ Required properties: * "allwinner,sun4i-a10-mmc" * "allwinner,sun5i-a13-mmc" * "allwinner,sun7i-a20-mmc" + * "allwinner,sun8i-a83t-emmc" * "allwinner,sun9i-a80-mmc" * "allwinner,sun50i-a64-emmc" * "allwinner,sun50i-a64-mmc" diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index 0e026c151c1c..3a4ac401e6f9 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -1,33 +1,55 @@ -* TI Highspeed MMC host controller for OMAP +* TI Highspeed MMC host controller for OMAP and 66AK2G family. -The Highspeed MMC Host Controller on TI OMAP family +The Highspeed MMC Host Controller on TI OMAP and 66AK2G family provides an interface for MMC, SD, and SDIO types of memory cards. This file documents differences between the core properties described by mmc.txt and the properties used by the omap_hsmmc driver. Required properties: +-------------------- - compatible: Should be "ti,omap2-hsmmc", for OMAP2 controllers Should be "ti,omap3-hsmmc", for OMAP3 controllers Should be "ti,omap3-pre-es3-hsmmc" for OMAP3 controllers pre ES3.0 Should be "ti,omap4-hsmmc", for OMAP4 controllers Should be "ti,am33xx-hsmmc", for AM335x controllers -- ti,hwmods: Must be "mmc<n>", n is controller instance starting 1 + Should be "ti,k2g-hsmmc", "ti,omap4-hsmmc" for 66AK2G controllers. + +SoC specific required properties: +--------------------------------- +The following are mandatory properties for OMAPs, AM33xx and AM43xx SoCs only: +- ti,hwmods: Must be "mmc<n>", n is controller instance starting 1. + +The following are mandatory properties for 66AK2G SoCs only: +- power-domains:Should contain a phandle to a PM domain provider node + and an args specifier containing the MMC device id + value. This property is as per the binding, + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt +- clocks: Must contain an entry for each entry in clock-names. Should + be defined as per the he appropriate clock bindings consumer + usage in Documentation/devicetree/bindings/clock/ti,sci-clk.txt +- clock-names: Shall be "fck" for the functional clock, + and "mmchsdb_fck" for the debounce clock. + Optional properties: -ti,dual-volt: boolean, supports dual voltage cards -<supply-name>-supply: phandle to the regulator device tree node -"supply-name" examples are "vmmc", "vmmc_aux"(deprecated)/"vqmmc" etc -ti,non-removable: non-removable slot (like eMMC) -ti,needs-special-reset: Requires a special softreset sequence -ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed -dmas: List of DMA specifiers with the controller specific format -as described in the generic DMA client binding. A tx and rx -specifier is required. -dma-names: List of DMA request names. These strings correspond -1:1 with the DMA specifiers listed in dmas. The string naming is -to be "rx" and "tx" for RX and TX DMA requests, respectively. +-------------------- +- ti,dual-volt: boolean, supports dual voltage cards +- <supply-name>-supply: phandle to the regulator device tree node + "supply-name" examples are "vmmc", + "vmmc_aux"(deprecated)/"vqmmc" etc +- ti,non-removable: non-removable slot (like eMMC) +- ti,needs-special-reset: Requires a special softreset sequence +- ti,needs-special-hs-handling: HSMMC IP needs special setting + for handling High Speed +- dmas: List of DMA specifiers with the controller specific + format as described in the generic DMA client + binding. A tx and rx specifier is required. +- dma-names: List of DMA request names. These strings correspond + 1:1 with the DMA specifiers listed in dmas. + The string naming is to be "rx" and "tx" for + RX and TX DMA requests, respectively. Examples: diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 4fd8b7acc510..54ef642f23a0 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -15,6 +15,8 @@ Required properties: "renesas,sdhi-r7s72100" - SDHI IP on R7S72100 SoC "renesas,sdhi-r8a73a4" - SDHI IP on R8A73A4 SoC "renesas,sdhi-r8a7740" - SDHI IP on R8A7740 SoC + "renesas,sdhi-r8a7743" - SDHI IP on R8A7743 SoC + "renesas,sdhi-r8a7745" - SDHI IP on R8A7745 SoC "renesas,sdhi-r8a7778" - SDHI IP on R8A7778 SoC "renesas,sdhi-r8a7779" - SDHI IP on R8A7779 SoC "renesas,sdhi-r8a7790" - SDHI IP on R8A7790 SoC @@ -33,10 +35,8 @@ Required properties: If 2 clocks are specified by the hardware, you must name them as "core" and "cd". If the controller only has 1 clock, naming is not required. - Below is the number clocks for each supported SoC: - 1: SH73A0, R8A73A4, R8A7740, R8A7778, R8A7779, R8A7790 - R8A7791, R8A7792, R8A7793, R8A7794, R8A7795, R8A7796 - 2: R7S72100 + Devices which have more than 1 clock are listed below: + 2: R7S72100 Optional properties: - toshiba,mmc-wrprotect-disable: write-protect detection is unavailable diff --git a/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt index 906819a90c2b..0f59bd5361f5 100644 --- a/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/zx-dw-mshc.txt @@ -28,5 +28,4 @@ Example: max-frequency = <50000000>; cap-sdio-irq; cap-sd-highspeed; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/mtd/atmel-quadspi.txt b/Documentation/devicetree/bindings/mtd/atmel-quadspi.txt index 489807005eda..b93c1e2f25dd 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-quadspi.txt @@ -24,7 +24,6 @@ spi@f0020000 { #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi0_default>; - status = "okay"; m25p80@0 { ... diff --git a/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt b/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt index 5ded66ad7aef..840f9405dcf0 100644 --- a/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt @@ -37,7 +37,6 @@ nor_flash: spi@1100d000 { clock-names = "spi", "sf"; #address-cells = <1>; #size-cells = <0>; - status = "disabled"; flash@0 { compatible = "jedec,spi-nor"; diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt index 70dd5118a324..73d336befa08 100644 --- a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt +++ b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt @@ -1,11 +1,20 @@ * Qualcomm NAND controller Required properties: -- compatible: should be "qcom,ipq806x-nand" +- compatible: must be one of the following: + * "qcom,ipq806x-nand" - for EBI2 NAND controller being used in IPQ806x + SoC and it uses ADM DMA + * "qcom,ipq4019-nand" - for QPIC NAND controller v1.4.0 being used in + IPQ4019 SoC and it uses BAM DMA + * "qcom,ipq8074-nand" - for QPIC NAND controller v1.5.0 being used in + IPQ8074 SoC and it uses BAM DMA + - reg: MMIO address range - clocks: must contain core clock and always on clock - clock-names: must contain "core" for the core clock and "aon" for the always on clock + +EBI2 specific properties: - dmas: DMA specifier, consisting of a phandle to the ADM DMA controller node and the channel number to be used for NAND. Refer to dma.txt and qcom_adm.txt for more details @@ -16,6 +25,12 @@ Required properties: - qcom,data-crci: must contain the ADM data type CRCI block instance number specified for the NAND controller on the given platform + +QPIC specific properties: +- dmas: DMA specifier, consisting of a phandle to the BAM DMA + and the channel number to be used for NAND. Refer to + dma.txt, qcom_bam_dma.txt for more details +- dma-names: must contain all 3 channel names : "tx", "rx", "cmd" - #address-cells: <1> - subnodes give the chip-select number - #size-cells: <0> @@ -26,7 +41,6 @@ chip-selects which (may) contain NAND flash chips. Their properties are as follows. Required properties: -- compatible: should contain "qcom,nandcs" - reg: a single integer representing the chip-select number (e.g., 0, 1, 2, etc.) - #address-cells: see partition.txt @@ -43,8 +57,8 @@ partition.txt for more detail. Example: -nand@1ac00000 { - compatible = "qcom,ebi2-nandc"; +nand-controller@1ac00000 { + compatible = "qcom,ipq806x-nand"; reg = <0x1ac00000 0x800>; clocks = <&gcc EBI2_CLK>, @@ -59,8 +73,7 @@ nand@1ac00000 { #address-cells = <1>; #size-cells = <0>; - nandcs@0 { - compatible = "qcom,nandcs"; + nand@0 { reg = <0>; nand-ecc-strength = <4>; @@ -84,3 +97,43 @@ nand@1ac00000 { }; }; }; + +nand-controller@79b0000 { + compatible = "qcom,ipq4019-nand"; + reg = <0x79b0000 0x1000>; + + clocks = <&gcc GCC_QPIC_CLK>, + <&gcc GCC_QPIC_AHB_CLK>; + clock-names = "core", "aon"; + + dmas = <&qpicbam 0>, + <&qpicbam 1>, + <&qpicbam 2>; + dma-names = "tx", "rx", "cmd"; + + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "boot-nand"; + reg = <0 0x58a0000>; + }; + + partition@58a0000 { + label = "fs-nand"; + reg = <0x58a0000 0x4000000>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/st-fsm.txt b/Documentation/devicetree/bindings/mtd/st-fsm.txt index c2489391c437..54cef9ef3083 100644 --- a/Documentation/devicetree/bindings/mtd/st-fsm.txt +++ b/Documentation/devicetree/bindings/mtd/st-fsm.txt @@ -21,6 +21,5 @@ Example: st,syscfg = <&syscfg_rear>; st,boot-device-reg = <0x958>; st,boot-device-spi = <0x1a>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt index f322f56aef74..a37c67bcb43b 100644 --- a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt @@ -41,7 +41,6 @@ nfc: nand@01c03000 { #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&nand_pins_a &nand_cs0_pins_a &nand_rb0_pins_a>; - status = "okay"; nand@0 { reg = <0>; diff --git a/Documentation/devicetree/bindings/net/anarion-gmac.txt b/Documentation/devicetree/bindings/net/anarion-gmac.txt new file mode 100644 index 000000000000..fe678965ae69 --- /dev/null +++ b/Documentation/devicetree/bindings/net/anarion-gmac.txt @@ -0,0 +1,25 @@ +* Adaptrum Anarion ethernet controller + +This device is a platform glue layer for stmmac. +Please see stmmac.txt for the other unchanged properties. + +Required properties: + - compatible: Should be "adaptrum,anarion-gmac", "snps,dwmac" + - phy-mode: Should be "rgmii". Other modes are not currently supported. + + +Examples: + + gmac1: ethernet@f2014000 { + compatible = "adaptrum,anarion-gmac", "snps,dwmac"; + reg = <0xf2014000 0x4000>, <0xf2018100 8>; + + interrupt-parent = <&core_intc>; + interrupts = <21>; + interrupt-names = "macirq"; + + clocks = <&core_clk>; + clock-names = "stmmaceth"; + + phy-mode = "rgmii"; + }; diff --git a/Documentation/devicetree/bindings/net/brcm,amac.txt b/Documentation/devicetree/bindings/net/brcm,amac.txt index ad16c1f481f7..0bfad656a9ff 100644 --- a/Documentation/devicetree/bindings/net/brcm,amac.txt +++ b/Documentation/devicetree/bindings/net/brcm,amac.txt @@ -27,5 +27,4 @@ amac0: ethernet@18022000 { <0x18110000 0x1000>; reg-names = "amac_base", "idm_base"; interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt new file mode 100644 index 000000000000..4194ff7e6ee6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt @@ -0,0 +1,35 @@ +Broadcom Bluetooth Chips +--------------------- + +This documents the binding structure and common properties for serial +attached Broadcom devices. + +Serial attached Broadcom devices shall be a child node of the host UART +device the slave device is attached to. + +Required properties: + + - compatible: should contain one of the following: + * "brcm,bcm43438-bt" + +Optional properties: + + - max-speed: see Documentation/devicetree/bindings/serial/slave-device.txt + - shutdown-gpios: GPIO specifier, used to enable the BT module + - device-wakeup-gpios: GPIO specifier, used to wakeup the controller + - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor + - clocks: clock specifier if external clock provided to the controller + - clock-names: should be "extclk" + + +Example: + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <921600>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/btusb.txt b/Documentation/devicetree/bindings/net/btusb.txt index 01fa2d4188d4..9c5e663fa1af 100644 --- a/Documentation/devicetree/bindings/net/btusb.txt +++ b/Documentation/devicetree/bindings/net/btusb.txt @@ -29,7 +29,6 @@ Example: Following example uses irq pin number 3 of gpio0 for out of band wake-on-bt: &usb_host1_ehci { - status = "okay"; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/net/can/c_can.txt b/Documentation/devicetree/bindings/net/can/c_can.txt index 5a1d8b0c39e9..2d504256b0d8 100644 --- a/Documentation/devicetree/bindings/net/can/c_can.txt +++ b/Documentation/devicetree/bindings/net/can/c_can.txt @@ -11,9 +11,20 @@ Required properties: - interrupts : property with a value describing the interrupt number -Optional properties: +The following are mandatory properties for DRA7x, AM33xx and AM43xx SoCs only: - ti,hwmods : Must be "d_can<n>" or "c_can<n>", n being the instance number + +The following are mandatory properties for Keystone 2 66AK2G SoCs only: +- power-domains : Should contain a phandle to a PM domain provider node + and an args specifier containing the DCAN device id + value. This property is as per the binding, + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt +- clocks : CAN functional clock phandle. This property is as per the + binding, + Documentation/devicetree/bindings/clock/ti,sci-clk.txt + +Optional properties: - syscon-raminit : Handle to system control region that contains the RAMINIT register, register offset to the RAMINIT register and the CAN instance number (0 offset). diff --git a/Documentation/devicetree/bindings/net/can/m_can.txt b/Documentation/devicetree/bindings/net/can/m_can.txt index 9e331777c203..78138333ff7a 100644 --- a/Documentation/devicetree/bindings/net/can/m_can.txt +++ b/Documentation/devicetree/bindings/net/can/m_can.txt @@ -56,7 +56,6 @@ m_can1: can@020e8000 { <&clks IMX6SX_CLK_CANFD>; clock-names = "hclk", "cclk"; bosch,mram-cfg = <0x0 0 0 32 0 0 0 1>; - status = "disabled"; }; Board dts: diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt index 0ab8b39d0b30..fd23904ac68e 100644 --- a/Documentation/devicetree/bindings/net/dsa/ksz.txt +++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt @@ -24,7 +24,6 @@ Ethernet switch connected via SPI to the host, CPU port wired to eth0: pinctrl-0 = <&pinctrl_spi_ksz>; cs-gpios = <&pioC 25 0>; id = <1>; - status = "okay"; ksz9477: ksz9477@0 { compatible = "microchip,ksz9477"; @@ -34,7 +33,6 @@ Ethernet switch connected via SPI to the host, CPU port wired to eth0: spi-cpha; spi-cpol; - status = "okay"; ports { #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/net/dsa/lan9303.txt b/Documentation/devicetree/bindings/net/dsa/lan9303.txt index 04f2965a4467..4448d063ddf6 100644 --- a/Documentation/devicetree/bindings/net/dsa/lan9303.txt +++ b/Documentation/devicetree/bindings/net/dsa/lan9303.txt @@ -27,7 +27,6 @@ Example: I2C managed mode: master: masterdevice@X { - status = "okay"; fixed-link { /* RMII fixed link to LAN9303 */ speed = <100>; @@ -38,7 +37,6 @@ I2C managed mode: switch: switch@a { compatible = "smsc,lan9303-i2c"; reg = <0xa>; - status = "okay"; reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>; reset-duration = <200>; @@ -67,7 +65,6 @@ I2C managed mode: MDIO managed mode: master: masterdevice@X { - status = "okay"; phy-handle = <&switch>; mdio { diff --git a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt deleted file mode 100644 index 725f3b187886..000000000000 --- a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt +++ /dev/null @@ -1,84 +0,0 @@ -* Allwinner sun8i GMAC ethernet controller - -This device is a platform glue layer for stmmac. -Please see stmmac.txt for the other unchanged properties. - -Required properties: -- compatible: should be one of the following string: - "allwinner,sun8i-a83t-emac" - "allwinner,sun8i-h3-emac" - "allwinner,sun8i-v3s-emac" - "allwinner,sun50i-a64-emac" -- reg: address and length of the register for the device. -- interrupts: interrupt for the device -- interrupt-names: should be "macirq" -- clocks: A phandle to the reference clock for this device -- clock-names: should be "stmmaceth" -- resets: A phandle to the reset control for this device -- reset-names: should be "stmmaceth" -- phy-mode: See ethernet.txt -- phy-handle: See ethernet.txt -- #address-cells: shall be 1 -- #size-cells: shall be 0 -- syscon: A phandle to the syscon of the SoC with one of the following - compatible string: - - allwinner,sun8i-h3-system-controller - - allwinner,sun8i-v3s-system-controller - - allwinner,sun50i-a64-system-controller - - allwinner,sun8i-a83t-system-controller - -Optional properties: -- allwinner,tx-delay-ps: TX clock delay chain value in ps. Range value is 0-700. Default is 0) -- allwinner,rx-delay-ps: RX clock delay chain value in ps. Range value is 0-3100. Default is 0) -Both delay properties need to be a multiple of 100. They control the delay for -external PHY. - -Optional properties for the following compatibles: - - "allwinner,sun8i-h3-emac", - - "allwinner,sun8i-v3s-emac": -- allwinner,leds-active-low: EPHY LEDs are active low - -Required child node of emac: -- mdio bus node: should be named mdio - -Required properties of the mdio node: -- #address-cells: shall be 1 -- #size-cells: shall be 0 - -The device node referenced by "phy" or "phy-handle" should be a child node -of the mdio node. See phy.txt for the generic PHY bindings. - -Required properties of the phy node with the following compatibles: - - "allwinner,sun8i-h3-emac", - - "allwinner,sun8i-v3s-emac": -- clocks: a phandle to the reference clock for the EPHY -- resets: a phandle to the reset control for the EPHY - -Example: - -emac: ethernet@1c0b000 { - compatible = "allwinner,sun8i-h3-emac"; - syscon = <&syscon>; - reg = <0x01c0b000 0x104>; - interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "macirq"; - resets = <&ccu RST_BUS_EMAC>; - reset-names = "stmmaceth"; - clocks = <&ccu CLK_BUS_EMAC>; - clock-names = "stmmaceth"; - #address-cells = <1>; - #size-cells = <0>; - - phy-handle = <&int_mii_phy>; - phy-mode = "mii"; - allwinner,leds-active-low; - mdio: mdio { - #address-cells = <1>; - #size-cells = <0>; - int_mii_phy: ethernet-phy@1 { - reg = <1>; - clocks = <&ccu CLK_BUS_EPHY>; - resets = <&ccu RST_BUS_EPHY>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt index 7da86f22a13b..2974e63ba311 100644 --- a/Documentation/devicetree/bindings/net/ethernet.txt +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -1,5 +1,9 @@ The following properties are common to the Ethernet controllers: +NOTE: All 'phy*' properties documented below are Ethernet specific. For the +generic PHY 'phys' property, see +Documentation/devicetree/bindings/phy/phy-bindings.txt. + - local-mac-address: array of 6 bytes, specifies the MAC address that was assigned to the network device; - mac-address: array of 6 bytes, specifies the MAC address that was last used by diff --git a/Documentation/devicetree/bindings/net/ftgmac100.txt b/Documentation/devicetree/bindings/net/ftgmac100.txt index c1ce1680246f..72e7aaf7242e 100644 --- a/Documentation/devicetree/bindings/net/ftgmac100.txt +++ b/Documentation/devicetree/bindings/net/ftgmac100.txt @@ -30,6 +30,5 @@ Example: compatible = "aspeed,ast2500-mac", "faraday,ftgmac100"; reg = <0x1e660000 0x180>; interrupts = <2>; - status = "okay"; use-ncsi; }; diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt index ae4234ca4ee4..bedcfd5a52cd 100644 --- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -41,7 +41,6 @@ ethernet@70000 { interrupts = <8>; clocks = <&gate_clk 4>; tx-csum-limit = <9800> - status = "okay"; phy = <&phy0>; phy-mode = "rgmii-id"; buffer-manager = <&bm>; diff --git a/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt b/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt index 9be1059ff03f..3d27c68613a6 100644 --- a/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt +++ b/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt @@ -44,7 +44,6 @@ Example for SDIO device follows (calibration data is also available in below example). &mmc3 { - status = "okay"; vmmc-supply = <&wlan_en_reg>; bus-width = <4>; cap-power-off-card; @@ -70,7 +69,6 @@ below example). Example for USB device: &usb_host1_ohci { - status = "okay"; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/net/marvell-neta-bm.txt b/Documentation/devicetree/bindings/net/marvell-neta-bm.txt index c1b1d7c3bde1..07b31050dbe5 100644 --- a/Documentation/devicetree/bindings/net/marvell-neta-bm.txt +++ b/Documentation/devicetree/bindings/net/marvell-neta-bm.txt @@ -31,7 +31,6 @@ bm: bm@c8000 { reg = <0xc8000 0xac>; clocks = <&gateclk 13>; internal-mem = <&bm_bppi>; - status = "okay"; pool2,capacity = <4096>; pool1,pkt-size = <512>; }; @@ -45,5 +44,4 @@ bm_bppi: bm-bppi { #address-cells = <1>; #size-cells = <1>; clocks = <&gateclk 13>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt index 6b4956beff8c..7e2dad08a12e 100644 --- a/Documentation/devicetree/bindings/net/marvell-pp2.txt +++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt @@ -41,6 +41,11 @@ Optional properties (port): - marvell,loopback: port is loopback mode - phy: a phandle to a phy node defining the PHY address (as the reg property, a single integer). +- interrupt-names: if more than a single interrupt for rx is given, must + be the name associated to the interrupts listed. Valid + names are: "tx-cpu0", "tx-cpu1", "tx-cpu2", "tx-cpu3", + "rx-shared", "link". +- marvell,system-controller: a phandle to the system controller. Example for marvell,armada-375-pp2: @@ -52,12 +57,10 @@ ethernet@f0000 { <0xc5000 0x100>; clocks = <&gateclk 3>, <&gateclk 19>; clock-names = "pp_clk", "gop_clk"; - status = "okay"; eth0: eth0@c4000 { interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; port-id = <0>; - status = "okay"; phy = <&phy0>; phy-mode = "gmii"; }; @@ -65,7 +68,6 @@ ethernet@f0000 { eth1: eth1@c5000 { interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; port-id = <1>; - status = "okay"; phy = <&phy3>; phy-mode = "gmii"; }; @@ -80,19 +82,37 @@ cpm_ethernet: ethernet@0 { clock-names = "pp_clk", "gop_clk", "gp_clk"; eth0: eth0 { - interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <ICU_GRP_NSR 39 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 43 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 47 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 51 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", + "tx-cpu3", "rx-shared"; port-id = <0>; gop-port-id = <0>; }; eth1: eth1 { - interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <ICU_GRP_NSR 40 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 44 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 48 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 52 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", + "tx-cpu3", "rx-shared"; port-id = <1>; gop-port-id = <2>; }; eth2: eth2 { - interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <ICU_GRP_NSR 41 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 45 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 49 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 53 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", + "tx-cpu3", "rx-shared"; port-id = <2>; gop-port-id = <3>; }; diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt index c7194e87d5f4..214eaa9a6683 100644 --- a/Documentation/devicetree/bindings/net/mediatek-net.txt +++ b/Documentation/devicetree/bindings/net/mediatek-net.txt @@ -7,24 +7,32 @@ have dual GMAC each represented by a child node.. * Ethernet controller node Required properties: -- compatible: Should be "mediatek,mt2701-eth" +- compatible: Should be + "mediatek,mt2701-eth": for MT2701 SoC + "mediatek,mt7623-eth", "mediatek,mt2701-eth": for MT7623 SoC + "mediatek,mt7622-eth": for MT7622 SoC - reg: Address and length of the register set for the device - interrupts: Should contain the three frame engines interrupts in numeric order. These are fe_int0, fe_int1 and fe_int2. - clocks: the clock used by the core - clock-names: the names of the clock listed in the clocks property. These are - "ethif", "esw", "gp2", "gp1" + "ethif", "esw", "gp2", "gp1" : For MT2701 and MT7623 SoC + "ethif", "esw", "gp0", "gp1", "gp2", "sgmii_tx250m", "sgmii_rx250m", + "sgmii_cdr_ref", "sgmii_cdr_fb", "sgmii_ck", "eth2pll" : For MT7622 SoC - power-domains: phandle to the power domain that the ethernet is part of -- resets: Should contain a phandle to the ethsys reset signal -- reset-names: Should contain the reset signal name "eth" +- resets: Should contain phandles to the ethsys reset signals +- reset-names: Should contain the names of reset signal listed in the resets + property + These are "fe", "gmac" and "ppe" - mediatek,ethsys: phandle to the syscon node that handles the port setup +- mediatek,sgmiisys: phandle to the syscon node that handles the SGMII setup + which is required for those SoCs equipped with SGMII such as MT7622 SoC. - mediatek,pctl: phandle to the syscon node that handles the ports slew rate and driver current Optional properties: - interrupt-parent: Should be the phandle for the interrupt controller that services interrupts for this device - * Ethernet MAC node Required properties: diff --git a/Documentation/devicetree/bindings/net/meson-dwmac.txt b/Documentation/devicetree/bindings/net/meson-dwmac.txt index 0703ad3f3c1e..354dd9896bb5 100644 --- a/Documentation/devicetree/bindings/net/meson-dwmac.txt +++ b/Documentation/devicetree/bindings/net/meson-dwmac.txt @@ -66,5 +66,4 @@ Example for GXBB: <&clkc CLKID_MPLL2>; clock-names = "stmmaceth", "clkin0", "clkin1"; phy-mode = "rgmii"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt index c35b5b428a7f..42a248301615 100644 --- a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt +++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt @@ -69,7 +69,6 @@ Examples: }; }; ethernet@70000 { - status = "okay"; phy = <&phy0>; phy-mode = "rgmii-id"; }; diff --git a/Documentation/devicetree/bindings/net/microchip,enc28j60.txt b/Documentation/devicetree/bindings/net/microchip,enc28j60.txt index 1dc3bc75539d..44dff53d4dda 100644 --- a/Documentation/devicetree/bindings/net/microchip,enc28j60.txt +++ b/Documentation/devicetree/bindings/net/microchip,enc28j60.txt @@ -33,7 +33,6 @@ Example (for NXP i.MX28 with pin control stuff for GPIO irq): compatible = "fsl,imx28-spi"; pinctrl-names = "default"; pinctrl-0 = <&spi2_pins_b &spi2_sck_cfg>; - status = "okay"; enc28j60: ethernet@0 { compatible = "microchip,enc28j60"; diff --git a/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt b/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt index 76df9173825a..c9b35251bb20 100644 --- a/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt +++ b/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt @@ -25,7 +25,6 @@ Optional I2C-based chip specific properties: Example (for ARM-based BeagleBoard Black with 88W8887 on UART5): &uart5 { - status = "okay"; nfcmrvluart: nfcmrvluart@5 { compatible = "marvell,nfc-uart"; @@ -41,7 +40,6 @@ Example (for ARM-based BeagleBoard Black with 88W8887 on UART5): Example (for ARM-based BeagleBoard Black with 88W8887 on I2C1): &i2c1 { - status = "okay"; clock-frequency = <400000>; nfcmrvli2c0: i2c@1 { diff --git a/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt b/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt index 5b6cd9b3f628..92486733df71 100644 --- a/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt +++ b/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt @@ -17,7 +17,6 @@ Example (for ARM-based BeagleBone with NPC100 NFC controller on I2C2): &i2c2 { - status = "okay"; npc100: npc100@29 { diff --git a/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt b/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt index 1aea822d4530..122460e42e3c 100644 --- a/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt +++ b/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt @@ -15,7 +15,6 @@ Example (for ARM-based BeagleBone with PN532 on I2C2): &i2c2 { - status = "okay"; pn532: pn532@24 { diff --git a/Documentation/devicetree/bindings/net/nfc/pn544.txt b/Documentation/devicetree/bindings/net/nfc/pn544.txt index dab69f36167c..538a86f7b2b0 100644 --- a/Documentation/devicetree/bindings/net/nfc/pn544.txt +++ b/Documentation/devicetree/bindings/net/nfc/pn544.txt @@ -17,7 +17,6 @@ Example (for ARM-based BeagleBone with PN544 on I2C2): &i2c2 { - status = "okay"; pn544: pn544@28 { diff --git a/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt b/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt index fb1e75facf1b..ed5b3eaadb39 100644 --- a/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt +++ b/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt @@ -12,7 +12,6 @@ Required properties: Example: &hsi2c_4 { - status = "okay"; s3fwrn5@27 { compatible = "samsung,s3fwrn5-i2c"; diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt index 263732e8879f..b46d473be425 100644 --- a/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt +++ b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt @@ -20,7 +20,6 @@ Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2): &i2c2 { - status = "okay"; st21nfcb: st21nfcb@8 { diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt index 711ca85a363d..54ce8e7ac681 100644 --- a/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt +++ b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt @@ -19,7 +19,6 @@ Example (for ARM-based BeagleBoard xM with ST21NFCB on SPI4): &mcspi4 { - status = "okay"; st21nfcb: st21nfcb@0 { diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfca.txt b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt index 7bb2e213d6f9..5ee9440fa9ad 100644 --- a/Documentation/devicetree/bindings/net/nfc/st21nfca.txt +++ b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt @@ -20,7 +20,6 @@ Example (for ARM-based BeagleBoard xM with ST21NFCA on I2C2): &i2c2 { - status = "okay"; st21nfca: st21nfca@1 { diff --git a/Documentation/devicetree/bindings/net/nfc/st95hf.txt b/Documentation/devicetree/bindings/net/nfc/st95hf.txt index ea3178bc9ddd..08a202e00d47 100644 --- a/Documentation/devicetree/bindings/net/nfc/st95hf.txt +++ b/Documentation/devicetree/bindings/net/nfc/st95hf.txt @@ -35,12 +35,10 @@ spi@9840000 { #address-cells = <1>; #size-cells = <0>; cs-gpios = <&pio0 4>; - status = "okay"; st95hf@0{ reg = <0>; compatible = "st,st95hf"; - status = "okay"; spi-max-frequency = <1000000>; enable-gpio = <&pio4 0>; interrupt-parent = <&pio0>; diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt index 60c833d62181..5ca9362ef127 100644 --- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt +++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt @@ -23,7 +23,6 @@ Optional SoC Specific Properties: Example (for ARM-based BeagleBone with TRF7970A on SPI1): &spi1 { - status = "okay"; nfc@0 { compatible = "ti,trf7970a"; @@ -41,6 +40,5 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1): irq-status-read-quirk; en2-rf-quirk; clock-frequency = <27120000>; - status = "okay"; }; }; diff --git a/Documentation/devicetree/bindings/net/oxnas-dwmac.txt b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt index df0534e2eda1..d7117a22fd87 100644 --- a/Documentation/devicetree/bindings/net/oxnas-dwmac.txt +++ b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt @@ -35,5 +35,4 @@ etha: ethernet@40400000 { /* Regmap for sys registers */ oxsemi,sys-ctrl = <&sys>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index b55857696fc3..77d0b2a61ffa 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -2,11 +2,7 @@ PHY nodes Required properties: - - interrupts : <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. + - interrupts : interrupt specifier for the sole interrupt. - interrupt-parent : the phandle for the interrupt controller that services interrupts for this device. - reg : The ID number for the phy, usually a small integer @@ -52,11 +48,16 @@ Optional Properties: Mark the corresponding energy efficient ethernet mode as broken and request the ethernet to stop advertising it. +- phy-is-integrated: If set, indicates that the PHY is integrated into the same + physical package as the Ethernet MAC. If needed, muxers should be configured + to ensure the integrated PHY is used. The absence of this property indicates + the muxers should be configured so that the external PHY is used. + Example: ethernet-phy@0 { compatible = "ethernet-phy-id0141.0e90", "ethernet-phy-ieee802.3-c22"; - interrupt-parent = <40000>; - interrupts = <35 1>; + interrupt-parent = <&PIC>; + interrupts = <35 IRQ_TYPE_EDGE_RISING>; reg = <0>; }; diff --git a/Documentation/devicetree/bindings/net/qca,qca7000.txt b/Documentation/devicetree/bindings/net/qca,qca7000.txt index 6d9efb2eb9a5..3987846b3fd3 100644 --- a/Documentation/devicetree/bindings/net/qca,qca7000.txt +++ b/Documentation/devicetree/bindings/net/qca,qca7000.txt @@ -41,7 +41,6 @@ ssp2: spi@80014000 { compatible = "fsl,imx28-spi"; pinctrl-names = "default"; pinctrl-0 = <&spi2_pins_a>; - status = "okay"; qca7000: ethernet@0 { compatible = "qca,qca7000"; @@ -78,7 +77,6 @@ auart0: serial@8006a000 { reg = <0x8006a000 0x2000>; pinctrl-names = "default"; pinctrl-0 = <&auart0_2pins_a>; - status = "okay"; qca7000: ethernet { compatible = "qca,qca7000"; diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index b519503be51a..16723535e1aa 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -4,19 +4,25 @@ This file provides information on what the device node for the Ethernet AVB interface contains. Required properties: -- compatible: "renesas,etheravb-r8a7790" if the device is a part of R8A7790 SoC. - "renesas,etheravb-r8a7791" if the device is a part of R8A7791 SoC. - "renesas,etheravb-r8a7792" if the device is a part of R8A7792 SoC. - "renesas,etheravb-r8a7793" if the device is a part of R8A7793 SoC. - "renesas,etheravb-r8a7794" if the device is a part of R8A7794 SoC. - "renesas,etheravb-r8a7795" if the device is a part of R8A7795 SoC. - "renesas,etheravb-r8a7796" if the device is a part of R8A7796 SoC. - "renesas,etheravb-rcar-gen2" for generic R-Car Gen 2 compatible interface. - "renesas,etheravb-rcar-gen3" for generic R-Car Gen 3 compatible interface. +- compatible: Must contain one or more of the following: + - "renesas,etheravb-r8a7743" for the R8A7743 SoC. + - "renesas,etheravb-r8a7745" for the R8A7745 SoC. + - "renesas,etheravb-r8a7790" for the R8A7790 SoC. + - "renesas,etheravb-r8a7791" for the R8A7791 SoC. + - "renesas,etheravb-r8a7792" for the R8A7792 SoC. + - "renesas,etheravb-r8a7793" for the R8A7793 SoC. + - "renesas,etheravb-r8a7794" for the R8A7794 SoC. + - "renesas,etheravb-rcar-gen2" as a fallback for the above + R-Car Gen2 and RZ/G1 devices. - When compatible with the generic version, nodes must list the - SoC-specific version corresponding to the platform first - followed by the generic version. + - "renesas,etheravb-r8a7795" for the R8A7795 SoC. + - "renesas,etheravb-r8a7796" for the R8A7796 SoC. + - "renesas,etheravb-rcar-gen3" as a fallback for the above + R-Car Gen3 devices. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first followed by + the generic version. - reg: offset and length of (1) the register block and (2) the stream buffer. - interrupts: A list of interrupt-specifiers, one for each entry in diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt index 8f427550720a..6af8eed1adeb 100644 --- a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt +++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt @@ -10,6 +10,7 @@ Required properties: "rockchip,rk3366-gmac": found on RK3366 SoCs "rockchip,rk3368-gmac": found on RK3368 SoCs "rockchip,rk3399-gmac": found on RK3399 SoCs + "rockchip,rv1108-gmac": found on RV1108 SoCs - reg: addresses and length of the register sets for the device. - interrupts: Should contain the GMAC interrupts. - interrupt-names: Should contain the interrupt names "macirq". @@ -70,5 +71,4 @@ gmac: ethernet@ff290000 { tx_delay = <0x30>; rx_delay = <0x10>; - status = "ok"; }; diff --git a/Documentation/devicetree/bindings/net/sff,sfp.txt b/Documentation/devicetree/bindings/net/sff,sfp.txt new file mode 100644 index 000000000000..60e970ce10ee --- /dev/null +++ b/Documentation/devicetree/bindings/net/sff,sfp.txt @@ -0,0 +1,76 @@ +Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP) +Transceiver + +Required properties: + +- compatible : must be "sff,sfp" + +Optional Properties: + +- i2c-bus : phandle of an I2C bus controller for the SFP two wire serial + interface + +- mod-def0-gpios : GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) + module presence input gpio signal, active (module absent) high + +- los-gpios : GPIO phandle and a specifier of the Receiver Loss of Signal + Indication input gpio signal, active (signal lost) high + +- tx-fault-gpios : GPIO phandle and a specifier of the Module Transmitter + Fault input gpio signal, active (fault condition) high + +- tx-disable-gpios : GPIO phandle and a specifier of the Transmitter Disable + output gpio signal, active (Tx disable) high + +- rate-select0-gpios : GPIO phandle and a specifier of the Rx Signaling Rate + Select (AKA RS0) output gpio signal, low: low Rx rate, high: high Rx rate + +- rate-select1-gpios : GPIO phandle and a specifier of the Tx Signaling Rate + Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high: + high Tx rate + +Example #1: Direct serdes to SFP connection + +sfp_eth3: sfp-eth3 { + compatible = "sff,sfp"; + i2c-bus = <&sfp_1g_i2c>; + los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>; + tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>; +}; + +&cps_emac3 { + phy-names = "comphy"; + phys = <&cps_comphy5 0>; + sfp = <&sfp_eth3>; +}; + +Example #2: Serdes to PHY to SFP connection + +sfp_eth0: sfp-eth0 { + compatible = "sff,sfp"; + i2c-bus = <&sfpp0_i2c>; + los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&cps_sfpp0_pins>; + tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>; +}; + +p0_phy: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + pinctrl-names = "default"; + pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>; + reg = <0>; + interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>; + sfp = <&sfp_eth0>; +}; + +&cpm_eth0 { + phy = <&p0_phy>; + phy-mode = "10gbase-kr"; +}; diff --git a/Documentation/devicetree/bindings/net/smsc-lan87xx.txt b/Documentation/devicetree/bindings/net/smsc-lan87xx.txt index 974edd5c85cc..8b7c719b0bb9 100644 --- a/Documentation/devicetree/bindings/net/smsc-lan87xx.txt +++ b/Documentation/devicetree/bindings/net/smsc-lan87xx.txt @@ -15,7 +15,6 @@ smsc phy with disabled energy detect mode on an am335x based board. pinctrl-names = "default", "sleep"; pinctrl-0 = <&davinci_mdio_default>; pinctrl-1 = <&davinci_mdio_sleep>; - status = "okay"; ethernetphy0: ethernet-phy@0 { reg = <0>; diff --git a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt index 2e68a3cd8513..b30d04b54ee9 100644 --- a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt +++ b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt @@ -40,7 +40,6 @@ gmii_to_sgmii_converter: phy@0x100000240 { gmac0: ethernet@ff700000 { compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac"; altr,sysmgr-syscon = <&sysmgr 0x60 0>; - status = "disabled"; reg = <0xff700000 0x2000>; interrupts = <0 115 4>; interrupt-names = "macirq"; diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt index d05c1e1fd9b6..062c5174add3 100644 --- a/Documentation/devicetree/bindings/net/sti-dwmac.txt +++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt @@ -34,7 +34,6 @@ Example: ethernet0: dwmac@9630000 { device_type = "network"; - status = "disabled"; compatible = "st,stih407-dwmac", "snps,dwmac", "snps,dwmac-3.710"; reg = <0x9630000 0x8000>; reg-names = "stmmaceth"; diff --git a/Documentation/devicetree/bindings/net/stm32-dwmac.txt b/Documentation/devicetree/bindings/net/stm32-dwmac.txt index c35afb7e956a..489dbcb66c5a 100644 --- a/Documentation/devicetree/bindings/net/stm32-dwmac.txt +++ b/Documentation/devicetree/bindings/net/stm32-dwmac.txt @@ -18,7 +18,6 @@ Example: ethernet@40028000 { compatible = "st,stm32-dwmac", "snps,dwmac-3.50a"; - status = "disabled"; reg = <0x40028000 0x8000>; reg-names = "stmmaceth"; interrupts = <0 61 0>, <0 62 0>; diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt index 590f622188de..b2bd4704f859 100644 --- a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt +++ b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt @@ -29,7 +29,6 @@ mmc3: mmc@01c12000 { vmmc-supply = <®_vmmc3>; bus-width = <4>; non-removable; - status = "okay"; brcmf: wifi@1 { reg = <1>; diff --git a/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt index 19331bb4ff6e..6830c4786f8a 100644 --- a/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt +++ b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt @@ -21,7 +21,6 @@ Example: mmc-pwrseq = <&wifi_pwrseq>; bus-width = <4>; non-removable; - status = "okay"; esp8089: sdio_wifi@1 { compatible = "esp,esp8089"; diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt index 0854451ff91d..59de8646862d 100644 --- a/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt +++ b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt @@ -48,7 +48,6 @@ IRQ pin 38 is used as system wakeup source interrupt. wakeup pin 3 is configured so that firmware can wakeup host using this device side pin. &mmc3 { - status = "okay"; vmmc-supply = <&wlan_en_reg>; mmc-pwrseq = <&wifi_pwrseq>; bus-width = <4>; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt index 7b2cbb14113e..f42f6b0f1bc7 100644 --- a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt @@ -31,7 +31,6 @@ clock, new bindings (for parsing the clock nodes) have to be added. Example: &mmc3 { - status = "okay"; vmmc-supply = <&wlan_en_reg>; bus-width = <4>; cap-power-off-card; diff --git a/Documentation/devicetree/bindings/net/xilinx_axienet.txt b/Documentation/devicetree/bindings/net/xilinx_axienet.txt new file mode 100644 index 000000000000..38f9ec076743 --- /dev/null +++ b/Documentation/devicetree/bindings/net/xilinx_axienet.txt @@ -0,0 +1,55 @@ +XILINX AXI ETHERNET Device Tree Bindings +-------------------------------------------------------- + +Also called AXI 1G/2.5G Ethernet Subsystem, the xilinx axi ethernet IP core +provides connectivity to an external ethernet PHY supporting different +interfaces: MII, GMII, RGMII, SGMII, 1000BaseX. It also includes two +segments of memory for buffering TX and RX, as well as the capability of +offloading TX/RX checksum calculation off the processor. + +Management configuration is done through the AXI interface, while payload is +sent and received through means of an AXI DMA controller. This driver +includes the DMA driver code, so this driver is incompatible with AXI DMA +driver. + +For more details about mdio please refer phy.txt file in the same directory. + +Required properties: +- compatible : Must be one of "xlnx,axi-ethernet-1.00.a", + "xlnx,axi-ethernet-1.01.a", "xlnx,axi-ethernet-2.01.a" +- reg : Address and length of the IO space. +- interrupts : Should be a list of two interrupt, TX and RX. +- phy-handle : Should point to the external phy device. + See ethernet.txt file in the same directory. +- xlnx,rxmem : Set to allocated memory buffer for Rx/Tx in the hardware + +Optional properties: +- phy-mode : See ethernet.txt +- xlnx,phy-type : Deprecated, do not use, but still accepted in preference + to phy-mode. +- xlnx,txcsum : 0 or empty for disabling TX checksum offload, + 1 to enable partial TX checksum offload, + 2 to enable full TX checksum offload +- xlnx,rxcsum : Same values as xlnx,txcsum but for RX checksum offload + +Example: + axi_ethernet_eth: ethernet@40c00000 { + compatible = "xlnx,axi-ethernet-1.00.a"; + device_type = "network"; + interrupt-parent = <µblaze_0_axi_intc>; + interrupts = <2 0>; + phy-mode = "mii"; + reg = <0x40c00000 0x40000>; + xlnx,rxcsum = <0x2>; + xlnx,rxmem = <0x800>; + xlnx,txcsum = <0x2>; + phy-handle = <&phy0>; + axi_ethernetlite_0_mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: phy@0 { + device_type = "ethernet-phy"; + reg = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt b/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt index 74cf52908a6c..0668c45a156d 100644 --- a/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt +++ b/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt @@ -3,7 +3,10 @@ This binding is intended to represent MTK-EFUSE which is found in most Mediatek SOCs. Required properties: -- compatible: should be "mediatek,mt8173-efuse" or "mediatek,efuse" +- compatible: should be + "mediatek,mt7622-efuse", "mediatek,efuse": for MT7622 + "mediatek,mt7623-efuse", "mediatek,efuse": for MT7623 + "mediatek,mt8173-efuse" or "mediatek,efuse": for MT8173 - reg: Should contain registers location and length = Data cells = diff --git a/Documentation/devicetree/bindings/nvmem/mxs-ocotp.txt b/Documentation/devicetree/bindings/nvmem/mxs-ocotp.txt index daebce9e6b07..372c72fd64dc 100644 --- a/Documentation/devicetree/bindings/nvmem/mxs-ocotp.txt +++ b/Documentation/devicetree/bindings/nvmem/mxs-ocotp.txt @@ -21,5 +21,4 @@ Example for i.MX28: #size-cells = <1>; reg = <0x8002c000 0x2000>; clocks = <&clks 25>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index e36d261b9ba6..9d733af26be7 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -464,7 +464,6 @@ Example 5: opp-supported-hw opp_table { compatible = "operating-points-v2"; - status = "okay"; opp-shared; opp-600000000 { diff --git a/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt b/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt index 35a465362408..b9165b72473c 100644 --- a/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt +++ b/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt @@ -1,11 +1,11 @@ * Freescale 83xx and 512x PCI bridges -Freescale 83xx and 512x SOCs include the same pci bridge core. +Freescale 83xx and 512x SOCs include the same PCI bridge core. 83xx/512x specific notes: - reg: should contain two address length tuples - The first is for the internal pci bridge registers - The second is for the pci config space access registers + The first is for the internal PCI bridge registers + The second is for the PCI config space access registers Example (MPC8313ERDB) pci0: pci@e0008500 { diff --git a/Documentation/devicetree/bindings/pci/aardvark-pci.txt b/Documentation/devicetree/bindings/pci/aardvark-pci.txt index bbcd9f4c501f..310ef7145c47 100644 --- a/Documentation/devicetree/bindings/pci/aardvark-pci.txt +++ b/Documentation/devicetree/bindings/pci/aardvark-pci.txt @@ -33,7 +33,6 @@ Example: pcie0: pcie@d0070000 { compatible = "marvell,armada-3700-pcie"; device_type = "pci"; - status = "disabled"; reg = <0 0xd0070000 0 0x20000>; #address-cells = <3>; #size-cells = <2>; diff --git a/Documentation/devicetree/bindings/pci/altera-pcie.txt b/Documentation/devicetree/bindings/pci/altera-pcie.txt index 2951a6a50704..495880193adc 100644 --- a/Documentation/devicetree/bindings/pci/altera-pcie.txt +++ b/Documentation/devicetree/bindings/pci/altera-pcie.txt @@ -7,21 +7,21 @@ Required properties: "Txs": TX slave port region "Cra": Control register access region - interrupt-parent: interrupt source phandle. -- interrupts: specifies the interrupt source of the parent interrupt controller. - The format of the interrupt specifier depends on the parent interrupt - controller. +- interrupts: specifies the interrupt source of the parent interrupt + controller. The format of the interrupt specifier depends + on the parent interrupt controller. - device_type: must be "pci" - #address-cells: set to <3> -- #size-cells: set to <2> +- #size-cells: set to <2> - #interrupt-cells: set to <1> -- ranges: describes the translation of addresses for root ports and standard - PCI regions. +- ranges: describes the translation of addresses for root ports and + standard PCI regions. - interrupt-map-mask and interrupt-map: standard PCI properties to define the mapping of the PCIe interface to interrupt numbers. Optional properties: -- msi-parent: Link to the hardware entity that serves as the MSI controller for this PCIe - controller. +- msi-parent: Link to the hardware entity that serves as the MSI controller + for this PCIe controller. - bus-range: PCI bus numbers covered Example @@ -45,5 +45,5 @@ Example <0 0 0 3 &pcie_0 3>, <0 0 0 4 &pcie_0 4>; ranges = <0x82000000 0x00000000 0x00000000 0xc0000000 0x00000000 0x10000000 - 0x82000000 0x00000000 0x10000000 0xd0000000 0x00000000 0x10000000>; + 0x82000000 0x00000000 0x10000000 0xd0000000 0x00000000 0x10000000>; }; diff --git a/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt index 5ecaea1e6eee..4e4aee4439ea 100644 --- a/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt +++ b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt @@ -6,7 +6,7 @@ and thus inherits all the common properties defined in designware-pcie.txt. Required properties: - compatible: "axis,artpec6-pcie", "snps,dw-pcie" - reg: base addresses and lengths of the PCIe controller (DBI), - the phy controller, and configuration address space. + the PHY controller, and configuration address space. - reg-names: Must include the following entries: - "dbi" - "phy" diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index b2480dd38c11..1da7ade3183c 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -1,4 +1,4 @@ -* Synopsys Designware PCIe interface +* Synopsys DesignWare PCIe interface Required properties: - compatible: should contain "snps,dw-pcie" to identify the core. @@ -17,29 +17,27 @@ RC mode: properties to define the mapping of the PCIe interface to interrupt numbers. EP mode: -- num-ib-windows: number of inbound address translation - windows -- num-ob-windows: number of outbound address translation - windows +- num-ib-windows: number of inbound address translation windows +- num-ob-windows: number of outbound address translation windows Optional properties: - num-lanes: number of lanes to use (this property should be specified unless the link is brought already up in BIOS) -- reset-gpio: gpio pin number of power good signal +- reset-gpio: GPIO pin number of power good signal - clocks: Must contain an entry for each entry in clock-names. See ../clocks/clock-bindings.txt for details. - clock-names: Must include the following entries: - "pcie" - "pcie_bus" RC mode: -- num-viewport: number of view ports configured in - hardware. If a platform does not specify it, the driver assumes 2. -- bus-range: PCI bus numbers covered (it is recommended - for new devicetrees to specify this property, to keep backwards - compatibility a range of 0x00-0xff is assumed if not present) +- num-viewport: number of view ports configured in hardware. If a platform + does not specify it, the driver assumes 2. +- bus-range: PCI bus numbers covered (it is recommended for new devicetrees + to specify this property, to keep backwards compatibility a range of + 0x00-0xff is assumed if not present) + EP mode: -- max-functions: maximum number of functions that can be - configured +- max-functions: maximum number of functions that can be configured Example configuration: diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index cf92d3ba5a26..7b1e48bf172b 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -1,6 +1,6 @@ * Freescale i.MX6 PCIe interface -This PCIe host controller is based on the Synopsis Designware PCIe IP +This PCIe host controller is based on the Synopsys DesignWare PCIe IP and thus inherits all the common properties defined in designware-pcie.txt. Required properties: diff --git a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt index a339dbb15493..bdb7ab39d2d7 100644 --- a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt +++ b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt @@ -1,7 +1,7 @@ HiSilicon Hip05 and Hip06 PCIe host bridge DT description -HiSilicon PCIe host controller is based on Designware PCI core. -It shares common functions with PCIe Designware core driver and inherits +HiSilicon PCIe host controller is based on the Synopsys DesignWare PCI core. +It shares common functions with the PCIe DesignWare core driver and inherits common properties defined in Documentation/devicetree/bindings/pci/designware-pci.txt. @@ -40,7 +40,6 @@ Hip05 Example (note that Hip06 is the same except compatible): 0x0 0 0 2 &mbigen_pcie 2 11 0x0 0 0 3 &mbigen_pcie 3 12 0x0 0 0 4 &mbigen_pcie 4 13>; - status = "ok"; }; HiSilicon Hip06/Hip07 PCIe host bridge DT (almost-ECAM) description. @@ -83,5 +82,4 @@ Example: 0x0 0 0 2 &mbigen_pcie0 650 4 0x0 0 0 3 &mbigen_pcie0 650 4 0x0 0 0 4 &mbigen_pcie0 650 4>; - status = "ok"; }; diff --git a/Documentation/devicetree/bindings/pci/kirin-pcie.txt b/Documentation/devicetree/bindings/pci/kirin-pcie.txt index 68ffa0fbcd73..6e217c63123d 100644 --- a/Documentation/devicetree/bindings/pci/kirin-pcie.txt +++ b/Documentation/devicetree/bindings/pci/kirin-pcie.txt @@ -1,8 +1,8 @@ HiSilicon Kirin SoCs PCIe host DT description -Kirin PCIe host controller is based on Designware PCI core. -It shares common functions with PCIe Designware core driver -and inherits common properties defined in +Kirin PCIe host controller is based on the Synopsys DesignWare PCI core. +It shares common functions with the PCIe DesignWare core driver and +inherits common properties defined in Documentation/devicetree/bindings/pci/designware-pci.txt. Additional properties are described here: @@ -16,7 +16,7 @@ Required properties "apb": apb Ctrl register defined by Kirin; "phy": apb PHY register defined by Kirin; "config": PCIe configuration space registers. -- reset-gpios: The gpio to generate PCIe perst assert and deassert signal. +- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal. Optional properties: diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt index ee1c72d5162e..c0484da0f20d 100644 --- a/Documentation/devicetree/bindings/pci/layerscape-pci.txt +++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -15,8 +15,10 @@ Required properties: - compatible: should contain the platform identifier such as: "fsl,ls1021a-pcie", "snps,dw-pcie" "fsl,ls2080a-pcie", "fsl,ls2085a-pcie", "snps,dw-pcie" + "fsl,ls2088a-pcie" + "fsl,ls1088a-pcie" "fsl,ls1046a-pcie" -- reg: base addresses and lengths of the PCIe controller +- reg: base addresses and lengths of the PCIe controller register blocks. - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. - interrupt-names: Must include the following entries: diff --git a/Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt deleted file mode 100644 index fe80dda9bf73..000000000000 --- a/Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt +++ /dev/null @@ -1,130 +0,0 @@ -MediaTek Gen2 PCIe controller which is available on MT7623 series SoCs - -PCIe subsys supports single root complex (RC) with 3 Root Ports. Each root -ports supports a Gen2 1-lane Link and has PIPE interface to PHY. - -Required properties: -- compatible: Should contain "mediatek,mt7623-pcie". -- device_type: Must be "pci" -- reg: Base addresses and lengths of the PCIe controller. -- #address-cells: Address representation for root ports (must be 3) -- #size-cells: Size representation for root ports (must be 2) -- #interrupt-cells: Size representation for interrupts (must be 1) -- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties - Please refer to the standard PCI bus binding document for a more detailed - explanation. -- clocks: Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. -- clock-names: Must include the following entries: - - free_ck :for reference clock of PCIe subsys - - sys_ck0 :for clock of Port0 - - sys_ck1 :for clock of Port1 - - sys_ck2 :for clock of Port2 -- resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. -- reset-names: Must include the following entries: - - pcie-rst0 :port0 reset - - pcie-rst1 :port1 reset - - pcie-rst2 :port2 reset -- phys: List of PHY specifiers (used by generic PHY framework). -- phy-names : Must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the - number of PHYs as specified in *phys* property. -- power-domains: A phandle and power domain specifier pair to the power domain - which is responsible for collapsing and restoring power to the peripheral. -- bus-range: Range of bus numbers associated with this controller. -- ranges: Ranges for the PCI memory and I/O regions. - -In addition, the device tree node must have sub-nodes describing each -PCIe port interface, having the following mandatory properties: - -Required properties: -- device_type: Must be "pci" -- reg: Only the first four bytes are used to refer to the correct bus number - and device number. -- #address-cells: Must be 3 -- #size-cells: Must be 2 -- #interrupt-cells: Must be 1 -- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties - Please refer to the standard PCI bus binding document for a more detailed - explanation. -- ranges: Sub-ranges distributed from the PCIe controller node. An empty - property is sufficient. -- num-lanes: Number of lanes to use for this port. - -Examples: - - hifsys: syscon@1a000000 { - compatible = "mediatek,mt7623-hifsys", - "mediatek,mt2701-hifsys", - "syscon"; - reg = <0 0x1a000000 0 0x1000>; - #clock-cells = <1>; - #reset-cells = <1>; - }; - - pcie: pcie-controller@1a140000 { - compatible = "mediatek,mt7623-pcie"; - device_type = "pci"; - reg = <0 0x1a140000 0 0x1000>, /* PCIe shared registers */ - <0 0x1a142000 0 0x1000>, /* Port0 registers */ - <0 0x1a143000 0 0x1000>, /* Port1 registers */ - <0 0x1a144000 0 0x1000>; /* Port2 registers */ - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - interrupt-map-mask = <0xf800 0 0 0>; - interrupt-map = <0x0000 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>, - <0x0800 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>, - <0x1000 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>; - clocks = <&topckgen CLK_TOP_ETHIF_SEL>, - <&hifsys CLK_HIFSYS_PCIE0>, - <&hifsys CLK_HIFSYS_PCIE1>, - <&hifsys CLK_HIFSYS_PCIE2>; - clock-names = "free_ck", "sys_ck0", "sys_ck1", "sys_ck2"; - resets = <&hifsys MT2701_HIFSYS_PCIE0_RST>, - <&hifsys MT2701_HIFSYS_PCIE1_RST>, - <&hifsys MT2701_HIFSYS_PCIE2_RST>; - reset-names = "pcie-rst0", "pcie-rst1", "pcie-rst2"; - phys = <&pcie0_phy>, <&pcie1_phy>, <&pcie2_phy>; - phy-names = "pcie-phy0", "pcie-phy1", "pcie-phy2"; - power-domains = <&scpsys MT2701_POWER_DOMAIN_HIF>; - bus-range = <0x00 0xff>; - ranges = <0x81000000 0 0x1a160000 0 0x1a160000 0 0x00010000 /* I/O space */ - 0x83000000 0 0x60000000 0 0x60000000 0 0x10000000>; /* memory space */ - - pcie@0,0 { - device_type = "pci"; - reg = <0x0000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>; - ranges; - num-lanes = <1>; - }; - - pcie@1,0 { - device_type = "pci"; - reg = <0x0800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>; - ranges; - num-lanes = <1>; - }; - - pcie@2,0 { - device_type = "pci"; - reg = <0x1000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>; - ranges; - num-lanes = <1>; - }; - }; diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt new file mode 100644 index 000000000000..3a6ce55dd310 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt @@ -0,0 +1,284 @@ +MediaTek Gen2 PCIe controller + +Required properties: +- compatible: Should contain one of the following strings: + "mediatek,mt2701-pcie" + "mediatek,mt2712-pcie" + "mediatek,mt7622-pcie" + "mediatek,mt7623-pcie" +- device_type: Must be "pci" +- reg: Base addresses and lengths of the PCIe subsys and root ports. +- reg-names: Names of the above areas to use during resource lookup. +- #address-cells: Address representation for root ports (must be 3) +- #size-cells: Size representation for root ports (must be 2) +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: + Mandatory entries: + - sys_ckN :transaction layer and data link layer clock + Required entries for MT2701/MT7623: + - free_ck :for reference clock of PCIe subsys + Required entries for MT2712/MT7622: + - ahb_ckN :AHB slave interface operating clock for CSR access and RC + initiated MMIO access + Required entries for MT7622: + - axi_ckN :application layer MMIO channel operating clock + - aux_ckN :pe2_mac_bridge and pe2_mac_core operating clock when + pcie_mac_ck/pcie_pipe_ck is turned off + - obff_ckN :OBFF functional block operating clock + - pipe_ckN :LTSSM and PHY/MAC layer operating clock + where N starting from 0 to one less than the number of root ports. +- phys: List of PHY specifiers (used by generic PHY framework). +- phy-names : Must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the + number of PHYs as specified in *phys* property. +- power-domains: A phandle and power domain specifier pair to the power domain + which is responsible for collapsing and restoring power to the peripheral. +- bus-range: Range of bus numbers associated with this controller. +- ranges: Ranges for the PCI memory and I/O regions. + +Required properties for MT7623/MT2701: +- #interrupt-cells: Size representation for interrupts (must be 1) +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must be "pcie-rst0", "pcie-rst1", "pcie-rstN".. based on the + number of root ports. + +Required properties for MT2712/MT7622: +-interrupts: A list of interrupt outputs of the controller, must have one + entry for each PCIe port + +In addition, the device tree node must have sub-nodes describing each +PCIe port interface, having the following mandatory properties: + +Required properties: +- device_type: Must be "pci" +- reg: Only the first four bytes are used to refer to the correct bus number + and device number. +- #address-cells: Must be 3 +- #size-cells: Must be 2 +- #interrupt-cells: Must be 1 +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- ranges: Sub-ranges distributed from the PCIe controller node. An empty + property is sufficient. +- num-lanes: Number of lanes to use for this port. + +Examples for MT7623: + + hifsys: syscon@1a000000 { + compatible = "mediatek,mt7623-hifsys", + "mediatek,mt2701-hifsys", + "syscon"; + reg = <0 0x1a000000 0 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + pcie: pcie-controller@1a140000 { + compatible = "mediatek,mt7623-pcie"; + device_type = "pci"; + reg = <0 0x1a140000 0 0x1000>, /* PCIe shared registers */ + <0 0x1a142000 0 0x1000>, /* Port0 registers */ + <0 0x1a143000 0 0x1000>, /* Port1 registers */ + <0 0x1a144000 0 0x1000>; /* Port2 registers */ + reg-names = "subsys", "port0", "port1", "port2"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 0>; + interrupt-map = <0x0000 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_ETHIF_SEL>, + <&hifsys CLK_HIFSYS_PCIE0>, + <&hifsys CLK_HIFSYS_PCIE1>, + <&hifsys CLK_HIFSYS_PCIE2>; + clock-names = "free_ck", "sys_ck0", "sys_ck1", "sys_ck2"; + resets = <&hifsys MT2701_HIFSYS_PCIE0_RST>, + <&hifsys MT2701_HIFSYS_PCIE1_RST>, + <&hifsys MT2701_HIFSYS_PCIE2_RST>; + reset-names = "pcie-rst0", "pcie-rst1", "pcie-rst2"; + phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>, + <&pcie2_phy PHY_TYPE_PCIE>; + phy-names = "pcie-phy0", "pcie-phy1", "pcie-phy2"; + power-domains = <&scpsys MT2701_POWER_DOMAIN_HIF>; + bus-range = <0x00 0xff>; + ranges = <0x81000000 0 0x1a160000 0 0x1a160000 0 0x00010000 /* I/O space */ + 0x83000000 0 0x60000000 0 0x60000000 0 0x10000000>; /* memory space */ + + pcie@0,0 { + device_type = "pci"; + reg = <0x0000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>; + ranges; + num-lanes = <1>; + }; + + pcie@1,0 { + device_type = "pci"; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>; + ranges; + num-lanes = <1>; + }; + + pcie@2,0 { + device_type = "pci"; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>; + ranges; + num-lanes = <1>; + }; + }; + +Examples for MT2712: + pcie: pcie@11700000 { + compatible = "mediatek,mt2712-pcie"; + device_type = "pci"; + reg = <0 0x11700000 0 0x1000>, + <0 0x112ff000 0 0x1000>; + reg-names = "port0", "port1"; + #address-cells = <3>; + #size-cells = <2>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>, + <&topckgen CLK_TOP_PE2_MAC_P1_SEL>, + <&pericfg CLK_PERI_PCIE0>, + <&pericfg CLK_PERI_PCIE1>; + clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1"; + phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>; + phy-names = "pcie-phy0", "pcie-phy1"; + bus-range = <0x00 0xff>; + ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; + + pcie0: pcie@0,0 { + device_type = "pci"; + reg = <0x0000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + num-lanes = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc0 0>, + <0 0 0 2 &pcie_intc0 1>, + <0 0 0 3 &pcie_intc0 2>, + <0 0 0 4 &pcie_intc0 3>; + pcie_intc0: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; + + pcie1: pcie@1,0 { + device_type = "pci"; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + num-lanes = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc1 0>, + <0 0 0 2 &pcie_intc1 1>, + <0 0 0 3 &pcie_intc1 2>, + <0 0 0 4 &pcie_intc1 3>; + pcie_intc1: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; + }; + +Examples for MT7622: + pcie: pcie@1a140000 { + compatible = "mediatek,mt7622-pcie"; + device_type = "pci"; + reg = <0 0x1a140000 0 0x1000>, + <0 0x1a143000 0 0x1000>, + <0 0x1a145000 0 0x1000>; + reg-names = "subsys", "port0", "port1"; + #address-cells = <3>; + #size-cells = <2>; + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pciesys CLK_PCIE_P0_MAC_EN>, + <&pciesys CLK_PCIE_P1_MAC_EN>, + <&pciesys CLK_PCIE_P0_AHB_EN>, + <&pciesys CLK_PCIE_P1_AHB_EN>, + <&pciesys CLK_PCIE_P0_AUX_EN>, + <&pciesys CLK_PCIE_P1_AUX_EN>, + <&pciesys CLK_PCIE_P0_AXI_EN>, + <&pciesys CLK_PCIE_P1_AXI_EN>, + <&pciesys CLK_PCIE_P0_OBFF_EN>, + <&pciesys CLK_PCIE_P1_OBFF_EN>, + <&pciesys CLK_PCIE_P0_PIPE_EN>, + <&pciesys CLK_PCIE_P1_PIPE_EN>; + clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1", + "aux_ck0", "aux_ck1", "axi_ck0", "axi_ck1", + "obff_ck0", "obff_ck1", "pipe_ck0", "pipe_ck1"; + phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>; + phy-names = "pcie-phy0", "pcie-phy1"; + power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>; + bus-range = <0x00 0xff>; + ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; + + pcie0: pcie@0,0 { + device_type = "pci"; + reg = <0x0000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + num-lanes = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc0 0>, + <0 0 0 2 &pcie_intc0 1>, + <0 0 0 3 &pcie_intc0 2>, + <0 0 0 4 &pcie_intc0 3>; + pcie_intc0: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; + + pcie1: pcie@1,0 { + device_type = "pci"; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + num-lanes = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc1 0>, + <0 0 0 2 &pcie_intc1 1>, + <0 0 0 3 &pcie_intc1 2>, + <0 0 0 4 &pcie_intc1 3>; + pcie_intc1: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/mvebu-pci.txt b/Documentation/devicetree/bindings/pci/mvebu-pci.txt index 2de6f65ecfb1..6173af6885f8 100644 --- a/Documentation/devicetree/bindings/pci/mvebu-pci.txt +++ b/Documentation/devicetree/bindings/pci/mvebu-pci.txt @@ -77,7 +77,7 @@ and the following optional properties: - marvell,pcie-lane: the physical PCIe lane number, for ports having multiple lanes. If this property is not found, we assume that the value is 0. -- reset-gpios: optional gpio to PERST# +- reset-gpios: optional GPIO to PERST# - reset-delay-us: delay in us to wait after reset de-assertion, if not specified will default to 100ms, as required by the PCIe specification. @@ -85,7 +85,6 @@ Example: pcie-controller { compatible = "marvell,armada-xp-pcie"; - status = "disabled"; device_type = "pci"; #address-cells = <3>; @@ -147,7 +146,6 @@ pcie-controller { /* wait 20ms for device settle after reset deassertion */ reset-delay-us = <20000>; clocks = <&gateclk 5>; - status = "disabled"; }; pcie@2,0 { @@ -164,7 +162,6 @@ pcie-controller { marvell,pcie-port = <0>; marvell,pcie-lane = <1>; clocks = <&gateclk 6>; - status = "disabled"; }; pcie@3,0 { @@ -181,7 +178,6 @@ pcie-controller { marvell,pcie-port = <0>; marvell,pcie-lane = <2>; clocks = <&gateclk 7>; - status = "disabled"; }; pcie@4,0 { @@ -198,7 +194,6 @@ pcie-controller { marvell,pcie-port = <0>; marvell,pcie-lane = <3>; clocks = <&gateclk 8>; - status = "disabled"; }; pcie@5,0 { @@ -215,7 +210,6 @@ pcie-controller { marvell,pcie-port = <1>; marvell,pcie-lane = <0>; clocks = <&gateclk 9>; - status = "disabled"; }; pcie@6,0 { @@ -232,7 +226,6 @@ pcie-controller { marvell,pcie-port = <1>; marvell,pcie-lane = <1>; clocks = <&gateclk 10>; - status = "disabled"; }; pcie@7,0 { @@ -249,7 +242,6 @@ pcie-controller { marvell,pcie-port = <1>; marvell,pcie-lane = <2>; clocks = <&gateclk 11>; - status = "disabled"; }; pcie@8,0 { @@ -266,7 +258,6 @@ pcie-controller { marvell,pcie-port = <1>; marvell,pcie-lane = <3>; clocks = <&gateclk 12>; - status = "disabled"; }; pcie@9,0 { @@ -283,10 +274,9 @@ pcie-controller { marvell,pcie-port = <2>; marvell,pcie-lane = <0>; clocks = <&gateclk 26>; - status = "disabled"; }; - pcie@10,0 { + pcie@a,0 { device_type = "pci"; assigned-addresses = <0x82005000 0 0x82000 0 0x2000>; reg = <0x5000 0 0 0 0>; @@ -300,6 +290,5 @@ pcie-controller { marvell,pcie-port = <3>; marvell,pcie-lane = <0>; clocks = <&gateclk 27>; - status = "disabled"; }; }; diff --git a/Documentation/devicetree/bindings/pci/pci-armada8k.txt b/Documentation/devicetree/bindings/pci/pci-armada8k.txt index 598533a57d79..c1e4c3d10a74 100644 --- a/Documentation/devicetree/bindings/pci/pci-armada8k.txt +++ b/Documentation/devicetree/bindings/pci/pci-armada8k.txt @@ -1,6 +1,6 @@ * Marvell Armada 7K/8K PCIe interface -This PCIe host controller is based on the Synopsis Designware PCIe IP +This PCIe host controller is based on the Synopsys DesignWare PCIe IP and thus inherits all the common properties defined in designware-pcie.txt. Required properties: @@ -34,5 +34,4 @@ Example: interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; num-lanes = <1>; clocks = <&cpm_syscon0 1 13>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt index d08a4d51108f..7e05487544ed 100644 --- a/Documentation/devicetree/bindings/pci/pci-keystone.txt +++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt @@ -1,12 +1,12 @@ TI Keystone PCIe interface -Keystone PCI host Controller is based on Designware PCI h/w version 3.65. -It shares common functions with PCIe Designware core driver and inherit -common properties defined in +Keystone PCI host Controller is based on the Synopsys DesignWare PCI +hardware version 3.65. It shares common functions with the PCIe DesignWare +core driver and inherits common properties defined in Documentation/devicetree/bindings/pci/designware-pci.txt Please refer to Documentation/devicetree/bindings/pci/designware-pci.txt -for the details of Designware DT bindings. Additional properties are +for the details of DesignWare DT bindings. Additional properties are described here as well as properties that are not applicable. Required Properties:- @@ -52,13 +52,12 @@ pcie_intc: Interrupt controller device node for Legacy IRQ chip }; Optional properties:- - phys: phandle to Generic Keystone SerDes phy for PCI - phy-names: name of the Generic Keystine SerDes phy for PCI + phys: phandle to generic Keystone SerDes PHY for PCI + phy-names: name of the generic Keystone SerDes PHY for PCI - If boot loader already does PCI link establishment, then phys and phy-names shouldn't be present. interrupts: platform interrupt for error interrupts. -Designware DT Properties not applicable for Keystone PCI +DesignWare DT Properties not applicable for Keystone PCI 1. pcie_bus clock-names not used. Instead, a phandle to phys is used. - diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt index 07a75094c5a8..3d038638612b 100644 --- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -6,11 +6,14 @@ AHB. There is one bridge instance per USB port connected to the internal OHCI and EHCI controllers. Required properties: -- compatible: "renesas,pci-r8a7790" for the R8A7790 SoC; +- compatible: "renesas,pci-r8a7743" for the R8A7743 SoC; + "renesas,pci-r8a7745" for the R8A7745 SoC; + "renesas,pci-r8a7790" for the R8A7790 SoC; "renesas,pci-r8a7791" for the R8A7791 SoC; "renesas,pci-r8a7793" for the R8A7793 SoC; "renesas,pci-r8a7794" for the R8A7794 SoC; - "renesas,pci-rcar-gen2" for a generic R-Car Gen2 compatible device + "renesas,pci-rcar-gen2" for a generic R-Car Gen2 or + RZ/G1 compatible device. When compatible with the generic version, nodes must list the diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt index 50f9e2ca5b13..c77981c5dd18 100644 --- a/Documentation/devicetree/bindings/pci/pci.txt +++ b/Documentation/devicetree/bindings/pci/pci.txt @@ -1,12 +1,12 @@ PCI bus bridges have standardized Device Tree bindings: PCI Bus Binding to: IEEE Std 1275-1994 -http://www.firmware.org/1275/bindings/pci/pci2_1.pdf +http://www.devicetree.org/open-firmware/bindings/pci/pci2_1.pdf And for the interrupt mapping part: Open Firmware Recommended Practice: Interrupt Mapping -http://www.firmware.org/1275/practice/imap/imap0_9d.pdf +http://www.devicetree.org/open-firmware/practice/imap/imap0_9d.pdf Additionally to the properties specified in the above standards a host bridge driver implementation may support the following properties: diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt index 9d418b71774f..3c9d321b3d3b 100644 --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt @@ -9,6 +9,7 @@ - "qcom,pcie-apq8084" for apq8084 - "qcom,pcie-msm8996" for msm8996 or apq8096 - "qcom,pcie-ipq4019" for ipq4019 + - "qcom,pcie-ipq8074" for ipq8074 - reg: Usage: required @@ -20,7 +21,7 @@ Value type: <stringlist> Definition: Must include the following entries - "parf" Qualcomm specific registers - - "dbi" Designware PCIe registers + - "dbi" DesignWare PCIe registers - "elbi" External local bus interface registers - "config" PCIe configuration space @@ -105,6 +106,16 @@ - "bus_master" Master AXI clock - "bus_slave" Slave AXI clock +- clock-names: + Usage: required for ipq8074 + Value type: <stringlist> + Definition: Should contain the following entries + - "iface" PCIe to SysNOC BIU clock + - "axi_m" AXI Master clock + - "axi_s" AXI Slave clock + - "ahb" AHB clock + - "aux" Auxiliary clock + - resets: Usage: required Value type: <prop-encoded-array> @@ -144,6 +155,18 @@ - "ahb" AHB reset - "phy_ahb" PHY AHB reset +- reset-names: + Usage: required for ipq8074 + Value type: <stringlist> + Definition: Should contain the following entries + - "pipe" PIPE reset + - "sleep" Sleep reset + - "sticky" Core Sticky reset + - "axi_m" AXI Master reset + - "axi_s" AXI Slave reset + - "ahb" AHB Reset + - "axi_m_sticky" AXI Master Sticky reset + - power-domains: Usage: required for apq8084 and msm8996/apq8096 Value type: <prop-encoded-array> @@ -180,7 +203,7 @@ - <name>-gpios: Usage: optional Value type: <prop-encoded-array> - Definition: List of phandle and gpio specifier pairs. Should contain + Definition: List of phandle and GPIO specifier pairs. Should contain - "perst-gpios" PCIe endpoint reset signal line - "wake-gpios" PCIe endpoint wake signal line diff --git a/Documentation/devicetree/bindings/pci/ralink,rt3883-pci.txt b/Documentation/devicetree/bindings/pci/ralink,rt3883-pci.txt index 8e0a1eb0acbb..a04ab1b76211 100644 --- a/Documentation/devicetree/bindings/pci/ralink,rt3883-pci.txt +++ b/Documentation/devicetree/bindings/pci/ralink,rt3883-pci.txt @@ -71,7 +71,7 @@ - interrupt-map: standard PCI properties to define the mapping of the PCI interface to interrupt numbers. - The PCI host bridge node migh have additional sub-nodes representing + The PCI host bridge node might have additional sub-nodes representing the onboard PCI devices/PCI slots. Each such sub-node must have the following mandatory properties: diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index bd27428dda61..76ba3a61d1a3 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -14,7 +14,7 @@ compatible: "renesas,pcie-r8a7779" for the R8A7779 SoC; SoC-specific version corresponding to the platform first followed by the generic version. -- reg: base address and length of the pcie controller registers. +- reg: base address and length of the PCIe controller registers. - #address-cells: set to <3> - #size-cells: set to <2> - bus-range: PCI bus numbers covered @@ -25,15 +25,14 @@ compatible: "renesas,pcie-r8a7779" for the R8A7779 SoC; source for hardware related interrupts (e.g. link speed change). - #interrupt-cells: set to <1> - interrupt-map-mask and interrupt-map: standard PCI properties - to define the mapping of the PCIe interface to interrupt - numbers. + to define the mapping of the PCIe interface to interrupt numbers. - clocks: from common clock binding: clock specifiers for the PCIe controller and PCIe bus clocks. - clock-names: from common clock binding: should be "pcie" and "pcie_bus". Example: -SoC specific DT Entry: +SoC-specific DT Entry: pcie: pcie@fe000000 { compatible = "renesas,pcie-r8a7791", "renesas,pcie-rcar-gen2"; @@ -54,5 +53,4 @@ SoC specific DT Entry: interrupt-map = <0 0 0 0 &gic 0 116 4>; clocks = <&mstp3_clks R8A7791_CLK_PCIE>, <&pcie_bus_clk>; clock-names = "pcie", "pcie_bus"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt index 1453a734c2f5..af34c65773fd 100644 --- a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt @@ -19,8 +19,6 @@ Required properties: - "pm" - msi-map: Maps a Requester ID to an MSI controller and associated msi-specifier data. See ./pci-msi.txt -- phys: From PHY bindings: Phandle for the Generic PHY for PCIe. -- phy-names: MUST be "pcie-phy". - interrupts: Three interrupt entries must be specified. - interrupt-names: Must include the following names - "sys" @@ -42,11 +40,24 @@ Required properties: interrupt source. The value must be 1. - interrupt-map-mask and interrupt-map: standard PCI properties +Required properties for legacy PHY model (deprecated): +- phys: From PHY bindings: Phandle for the Generic PHY for PCIe. +- phy-names: MUST be "pcie-phy". + +Required properties for per-lane PHY model (preferred): +- phys: Must contain an phandle to a PHY for each entry in phy-names. +- phy-names: Must include 4 entries for all 4 lanes even if some of + them won't be used for your cases. Entries are of the form "pcie-phy-N": + where N ranges from 0 to 3. + (see example below and you MUST also refer to ../phy/rockchip-pcie-phy.txt + for changing the #phy-cells of phy node to support it) + Optional Property: - aspm-no-l0s: RC won't support ASPM L0s. This property is needed if using 24MHz OSC for RC's PHY. -- ep-gpios: contain the entry for pre-reset gpio +- ep-gpios: contain the entry for pre-reset GPIO - num-lanes: number of lanes to use +- vpcie12v-supply: The phandle to the 12v regulator to use for PCIe. - vpcie3v3-supply: The phandle to the 3.3v regulator to use for PCIe. - vpcie1v8-supply: The phandle to the 1.8v regulator to use for PCIe. - vpcie0v9-supply: The phandle to the 0.9v regulator to use for PCIe. @@ -95,6 +106,7 @@ pcie0: pcie@f8000000 { <&cru SRST_PCIE_PM>, <&cru SRST_P_PCIE>, <&cru SRST_A_PCIE>; reset-names = "core", "mgmt", "mgmt-sticky", "pipe", "pm", "pclk", "aclk"; + /* deprecated legacy PHY model */ phys = <&pcie_phy>; phy-names = "pcie-phy"; pinctrl-names = "default"; @@ -111,3 +123,13 @@ pcie0: pcie@f8000000 { #interrupt-cells = <1>; }; }; + +pcie0: pcie@f8000000 { + ... + + /* preferred per-lane PHY model */ + phys = <&pcie_phy 0>, <&pcie_phy 1>, <&pcie_phy 2>, <&pcie_phy 3>; + phy-names = "pcie-phy-0", "pcie-phy-1", "pcie-phy-2", "pcie-phy-3"; + + ... +}; diff --git a/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt index 7d3b09474657..34a11bfbfb60 100644 --- a/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt +++ b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt @@ -1,29 +1,29 @@ * Samsung Exynos 5440 PCIe interface -This PCIe host controller is based on the Synopsis Designware PCIe IP +This PCIe host controller is based on the Synopsys DesignWare PCIe IP and thus inherits all the common properties defined in designware-pcie.txt. Required properties: - compatible: "samsung,exynos5440-pcie" -- reg: base addresses and lengths of the pcie controller, - the phy controller, additional register for the phy controller. - (Registers for the phy controller are DEPRECATED. +- reg: base addresses and lengths of the PCIe controller, + the PHY controller, additional register for the PHY controller. + (Registers for the PHY controller are DEPRECATED. Use the PHY framework.) - reg-names : First name should be set to "elbi". - And use the "config" instead of getting the confgiruation address space + And use the "config" instead of getting the configuration address space from "ranges". - NOTE: When use the "config" property, reg-names must be set. + NOTE: When using the "config" property, reg-names must be set. - interrupts: A list of interrupt outputs for level interrupt, pulse interrupt, special interrupt. -- phys: From PHY binding. Phandle for the Generic PHY. +- phys: From PHY binding. Phandle for the generic PHY. Refer to Documentation/devicetree/bindings/phy/samsung-phy.txt -Other common properties refer to - Documentation/devicetree/binding/pci/designware-pcie.txt +For other common properties, refer to + Documentation/devicetree/bindings/pci/designware-pcie.txt Example: -SoC specific DT Entry: +SoC-specific DT Entry: pcie@290000 { compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; @@ -83,7 +83,7 @@ With using PHY framework: ... }; -Board specific DT Entry: +Board-specific DT Entry: pcie@290000 { reset-gpio = <&pin_ctrl 5 0>; diff --git a/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt b/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt index 49ea76da7718..d5a14f5dad46 100644 --- a/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt +++ b/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt @@ -1,12 +1,12 @@ SPEAr13XX PCIe DT detail: ================================ -SPEAr13XX uses synopsis designware PCIe controller and ST MiPHY as phy +SPEAr13XX uses the Synopsys DesignWare PCIe controller and ST MiPHY as PHY controller. Required properties: -- compatible : should be "st,spear1340-pcie", "snps,dw-pcie". -- phys : phandle to phy node associated with pcie controller +- compatible : should be "st,spear1340-pcie", "snps,dw-pcie". +- phys : phandle to PHY node associated with PCIe controller - phy-names : must be "pcie-phy" - All other definitions as per generic PCI bindings diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt index 6a07c96227e0..7f7af3044016 100644 --- a/Documentation/devicetree/bindings/pci/ti-pci.txt +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt @@ -1,6 +1,6 @@ TI PCI Controllers -PCIe Designware Controller +PCIe DesignWare Controller - compatible: Should be "ti,dra7-pcie" for RC Should be "ti,dra7-pcie-ep" for EP - phys : list of PHY specifiers (used by generic PHY framework) @@ -13,7 +13,7 @@ PCIe Designware Controller HOST MODE ========= - reg : Two register ranges as listed in the reg-names property - - reg-names : The first entry must be "ti-conf" for the TI specific registers + - reg-names : The first entry must be "ti-conf" for the TI-specific registers The second entry must be "rc-dbics" for the DesignWare PCIe registers The third entry must be "config" for the PCIe configuration space @@ -30,7 +30,7 @@ HOST MODE DEVICE MODE =========== - reg : Four register ranges as listed in the reg-names property - - reg-names : "ti-conf" for the TI specific registers + - reg-names : "ti-conf" for the TI-specific registers "ep_dbics" for the standard configuration registers as they are locally accessed within the DIF CS space "ep_dbics2" for the standard configuration registers as @@ -46,7 +46,7 @@ DEVICE MODE access. Optional Property: - - gpios : Should be added if a gpio line is required to drive PERST# line + - gpios : Should be added if a GPIO line is required to drive PERST# line NOTE: Two DT nodes may be added for each PCI controller; one for host mode and another for device mode. So in order for PCI to diff --git a/Documentation/devicetree/bindings/pci/versatile.txt b/Documentation/devicetree/bindings/pci/versatile.txt index ebd1e7d0403e..0a702b13d2ac 100644 --- a/Documentation/devicetree/bindings/pci/versatile.txt +++ b/Documentation/devicetree/bindings/pci/versatile.txt @@ -5,7 +5,7 @@ PCI host controller found on the ARM Versatile PB board's FPGA. Required properties: - compatible: should contain "arm,versatile-pci" to identify the Versatile PCI controller. -- reg: base addresses and lengths of the pci controller. There must be 3 +- reg: base addresses and lengths of the PCI controller. There must be 3 entries: - Versatile-specific registers - Self Config space diff --git a/Documentation/devicetree/bindings/pci/xgene-pci-msi.txt b/Documentation/devicetree/bindings/pci/xgene-pci-msi.txt index 36d881c8e6d4..85d9b95234f7 100644 --- a/Documentation/devicetree/bindings/pci/xgene-pci-msi.txt +++ b/Documentation/devicetree/bindings/pci/xgene-pci-msi.txt @@ -4,7 +4,7 @@ Required properties: - compatible: should be "apm,xgene1-msi" to identify X-Gene v1 PCIe MSI controller block. -- msi-controller: indicates that this is X-Gene v1 PCIe MSI controller node +- msi-controller: indicates that this is an X-Gene v1 PCIe MSI controller node - reg: physical base address (0x79000000) and length (0x900000) for controller registers. These registers include the MSI termination address and data registers as well as the MSI interrupt status registers. @@ -13,7 +13,8 @@ Required properties: interrupt number 0x10 to 0x1f. - interrupt-names: not required -Each PCIe node needs to have property msi-parent that points to msi controller node +Each PCIe node needs to have property msi-parent that points to an MSI +controller node Examples: @@ -44,7 +45,6 @@ SoC DTSI: + PCIe controller node with msi-parent property pointing to MSI node: pcie0: pcie@1f2b0000 { - status = "disabled"; device_type = "pci"; compatible = "apm,xgene-storm-pcie", "apm,xgene-pcie"; #interrupt-cells = <1>; diff --git a/Documentation/devicetree/bindings/pci/xgene-pci.txt b/Documentation/devicetree/bindings/pci/xgene-pci.txt index 1070b068c7c6..6fd2decfa66c 100644 --- a/Documentation/devicetree/bindings/pci/xgene-pci.txt +++ b/Documentation/devicetree/bindings/pci/xgene-pci.txt @@ -8,7 +8,7 @@ Required properties: property. - reg-names: Must include the following entries: "csr": controller configuration registers. - "cfg": pcie configuration space registers. + "cfg": PCIe configuration space registers. - #address-cells: set to <3> - #size-cells: set to <2> - ranges: ranges for the outbound memory, I/O regions. @@ -21,11 +21,11 @@ Required properties: Optional properties: - status: Either "ok" or "disabled". -- dma-coherent: Present if dma operations are coherent +- dma-coherent: Present if DMA operations are coherent Example: -SoC specific DT Entry: +SoC-specific DT Entry: pcie0: pcie@1f2b0000 { status = "disabled"; @@ -51,7 +51,7 @@ SoC specific DT Entry: }; -Board specific DT Entry: +Board-specific DT Entry: &pcie0 { status = "ok"; }; diff --git a/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt index 3259798a1192..01bf7fdf4c19 100644 --- a/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt +++ b/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt @@ -15,9 +15,9 @@ Required properties: - device_type: must be "pci" - interrupts: Should contain NWL PCIe interrupt - interrupt-names: Must include the following entries: - "msi1, msi0": interrupt asserted when MSI is received + "msi1, msi0": interrupt asserted when an MSI is received "intx": interrupt asserted when a legacy interrupt is received - "misc": interrupt asserted when miscellaneous is received + "misc": interrupt asserted when miscellaneous interrupt is received - interrupt-map-mask and interrupt-map: standard PCI properties to define the mapping of the PCI interface to interrupt numbers. - ranges: ranges for the PCI memory regions (I/O space region is not @@ -26,7 +26,8 @@ Required properties: detailed explanation - msi-controller: indicates that this is MSI controller node - msi-parent: MSI parent of the root complex itself -- legacy-interrupt-controller: Interrupt controller device node for Legacy interrupts +- legacy-interrupt-controller: Interrupt controller device node for Legacy + interrupts - interrupt-controller: identifies the node as an interrupt controller - #interrupt-cells: should be set to 1 - #address-cells: specifies the number of cells needed to encode an diff --git a/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt b/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt index 5f3a65a9dd88..e1bb12711fbf 100644 --- a/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt +++ b/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt @@ -61,19 +61,16 @@ Example: compatible = "apm,xgene-phy"; reg = <0x0 0x1f21a000 0x0 0x100>; #phy-cells = <1>; - status = "disabled"; }; phy2: phy@1f22a000 { compatible = "apm,xgene-phy"; reg = <0x0 0x1f22a000 0x0 0x100>; #phy-cells = <1>; - status = "ok"; }; phy3: phy@1f23a000 { compatible = "apm,xgene-phy"; reg = <0x0 0x1f23a000 0x0 0x100>; #phy-cells = <1>; - status = "ok"; }; diff --git a/Documentation/devicetree/bindings/phy/keystone-usb-phy.txt b/Documentation/devicetree/bindings/phy/keystone-usb-phy.txt index f37b3a86341d..300830dda0bf 100644 --- a/Documentation/devicetree/bindings/phy/keystone-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/keystone-usb-phy.txt @@ -16,5 +16,4 @@ usb_phy: usb_phy@2620738 { #address-cells = <1>; #size-cells = <1>; reg = <0x2620738 32>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/phy/phy-bindings.txt b/Documentation/devicetree/bindings/phy/phy-bindings.txt index 1293c321754c..a403b81d0679 100644 --- a/Documentation/devicetree/bindings/phy/phy-bindings.txt +++ b/Documentation/devicetree/bindings/phy/phy-bindings.txt @@ -34,7 +34,9 @@ PHY user node ============= Required Properties: -phys : the phandle for the PHY device (used by the PHY subsystem) +phys : the phandle for the PHY device (used by the PHY subsystem; not to be + confused with the Ethernet specific 'phy' and 'phy-handle' properties, + see Documentation/devicetree/bindings/net/ethernet.txt for these) phy-names : the names of the PHY corresponding to the PHYs present in the *phys* phandle diff --git a/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt new file mode 100644 index 000000000000..643948b6b576 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt @@ -0,0 +1,40 @@ +Lantiq XWAY SoC RCU USB 1.1/2.0 PHY binding +=========================================== + +This binding describes the USB PHY hardware provided by the RCU module on the +Lantiq XWAY SoCs. + +This node has to be a sub node of the Lantiq RCU block. + +------------------------------------------------------------------------------- +Required properties (controller (parent) node): +- compatible : Should be one of + "lantiq,ase-usb2-phy" + "lantiq,danube-usb2-phy" + "lantiq,xrx100-usb2-phy" + "lantiq,xrx200-usb2-phy" + "lantiq,xrx300-usb2-phy" +- reg : Defines the following sets of registers in the parent + syscon device + - Offset of the USB PHY configuration register + - Offset of the USB Analog configuration + register (only for xrx200 and xrx200) +- clocks : References to the (PMU) "phy" clk gate. +- clock-names : Must be "phy" +- resets : References to the RCU USB configuration reset bits. +- reset-names : Must be one of the following: + "phy" (optional) + "ctrl" (shared) + +------------------------------------------------------------------------------- +Example for the USB PHYs on an xRX200 SoC: + usb_phy0: usb2-phy@18 { + compatible = "lantiq,xrx200-usb2-phy"; + reg = <0x18 4>, <0x38 4>; + + clocks = <&pmu PMU_GATE_USB0_PHY>; + clock-names = "phy"; + resets = <&reset1 4 4>, <&reset0 4 4>; + reset-names = "phy", "ctrl"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mtk-tphy.txt index 0acc5a99fb79..41e09ed2ca70 100644 --- a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt +++ b/Documentation/devicetree/bindings/phy/phy-mtk-tphy.txt @@ -1,13 +1,18 @@ -mt65xx USB3.0 PHY binding +MediaTek T-PHY binding -------------------------- -This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC. +T-phy controller supports physical layer functionality for a number of +controllers on MediaTek SoCs, such as, USB2.0, USB3.0, PCIe, and SATA. Required properties (controller (parent) node): - compatible : should be one of - "mediatek,mt2701-u3phy" - "mediatek,mt2712-u3phy" - "mediatek,mt8173-u3phy" + "mediatek,generic-tphy-v1" + "mediatek,generic-tphy-v2" + "mediatek,mt2701-u3phy" (deprecated) + "mediatek,mt2712-u3phy" (deprecated) + "mediatek,mt8173-u3phy"; + make use of "mediatek,generic-tphy-v1" on mt2701 instead and + "mediatek,generic-tphy-v2" on mt2712 instead. - clocks : (deprecated, use port's clocks instead) a list of phandle + clock-specifier pairs, one for each entry in clock-names - clock-names : (deprecated, use port's one instead) must contain @@ -35,6 +40,8 @@ Required properties (port (child) node): cell after port phandle is phy type from: - PHY_TYPE_USB2 - PHY_TYPE_USB3 + - PHY_TYPE_PCIE + - PHY_TYPE_SATA Example: @@ -44,14 +51,12 @@ u3phy: usb-phy@11290000 { #address-cells = <2>; #size-cells = <2>; ranges; - status = "okay"; u2port0: usb-phy@11290800 { reg = <0 0x11290800 0 0x100>; clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; clock-names = "ref"; #phy-cells = <1>; - status = "okay"; }; u3port0: usb-phy@11290900 { @@ -59,7 +64,6 @@ u3phy: usb-phy@11290000 { clocks = <&clk26m>; clock-names = "ref"; #phy-cells = <1>; - status = "okay"; }; u2port1: usb-phy@11291000 { @@ -67,7 +71,6 @@ u3phy: usb-phy@11290000 { clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; clock-names = "ref"; #phy-cells = <1>; - status = "okay"; }; }; diff --git a/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt b/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt new file mode 100644 index 000000000000..bfcf80341657 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt @@ -0,0 +1,43 @@ +mvebu comphy driver +------------------- + +A comphy controller can be found on Marvell Armada 7k/8k on the CP110. It +provides a number of shared PHYs used by various interfaces (network, sata, +usb, PCIe...). + +Required properties: + +- compatible: should be "marvell,comphy-cp110" +- reg: should contain the comphy register location and length. +- marvell,system-controller: should contain a phandle to the + system controller node. +- #address-cells: should be 1. +- #size-cells: should be 0. + +A sub-node is required for each comphy lane provided by the comphy. + +Required properties (child nodes): + +- reg: comphy lane number. +- #phy-cells : from the generic phy bindings, must be 1. Defines the + input port to use for a given comphy lane. + +Example: + + cpm_comphy: phy@120000 { + compatible = "marvell,comphy-cp110"; + reg = <0x120000 0x6000>; + marvell,system-controller = <&cpm_syscon0>; + #address-cells = <1>; + #size-cells = <0>; + + cpm_comphy0: phy@0 { + reg = <0>; + #phy-cells = <1>; + }; + + cpm_comphy1: phy@1 { + reg = <1>; + #phy-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-mvebu.txt b/Documentation/devicetree/bindings/phy/phy-mvebu.txt index f95b6260a3b3..64afdd13d91d 100644 --- a/Documentation/devicetree/bindings/phy/phy-mvebu.txt +++ b/Documentation/devicetree/bindings/phy/phy-mvebu.txt @@ -18,7 +18,6 @@ Example: clocks = <&gate_clk 15>; clock-names = "sata"; #phy-cells = <0>; - status = "ok"; }; Armada 375 USB cluster diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt index 84d59b0db8df..074a7b3b0425 100644 --- a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt @@ -6,6 +6,7 @@ Required properties (phy (parent) node): * "rockchip,rk3328-usb2phy" * "rockchip,rk3366-usb2phy" * "rockchip,rk3399-usb2phy" + * "rockchip,rv1108-usb2phy" - reg : the address offset of grf for usb-phy configuration. - #clock-cells : should be 0. - clock-output-names : specify the 480m output clock name. @@ -18,6 +19,10 @@ Optional properties: usb-phy output 480m and xin24m. Refer to clk/clock-bindings.txt for generic clock consumer properties. + - rockchip,usbgrf : phandle to the syscon managing the "usb general + register files". When set driver will request its + phandle as one companion-grf for some special SoCs + (e.g RV1108). Required nodes : a sub-node is required for each port the phy provides. The sub-node name is used to identify host or otg port, @@ -28,10 +33,14 @@ Required nodes : a sub-node is required for each port the phy provides. Required properties (port (child) node): - #phy-cells : must be 0. See ./phy-bindings.txt for details. - interrupts : specify an interrupt for each entry in interrupt-names. - - interrupt-names : a list which shall be the following entries: + - interrupt-names : a list which should be one of the following cases: + Regular case: * "otg-id" : for the otg id interrupt. * "otg-bvalid" : for the otg vbus interrupt. * "linestate" : for the host/otg linestate interrupt. + Some SoCs use one interrupt with the above muxed together, so for these + * "otg-mux" : otg-port interrupt, which mux otg-id/otg-bvalid/linestate + to one. Optional properties: - phy-supply : phandle to a regulator that provides power to VBUS. @@ -58,14 +67,12 @@ grf: syscon@ff770000 { <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "otg-id", "otg-bvalid", "linestate"; - status = "okay"; }; u2phy_host: host-port { #phy-cells = <0>; interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "linestate"; - status = "okay"; }; }; }; diff --git a/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt b/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt index 86f2dbe07ed4..a1697c27aecd 100644 --- a/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt @@ -25,7 +25,6 @@ Example: clock-names = "ref"; #phy-cells = <0>; - status = "ok"; }; phy@100f8830 { @@ -35,5 +34,4 @@ Example: clock-names = "ref"; #phy-cells = <0>; - status = "ok"; }; diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt index e11c563a65ec..b6a9f2b92bab 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt @@ -6,6 +6,7 @@ controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB. Required properties: - compatible: compatible list, contains: + "qcom,ipq8074-qmp-pcie-phy" for PCIe phy on IPQ8074 "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996, "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996. @@ -38,6 +39,8 @@ Required properties: "phy", "common", "cfg". For "qcom,msm8996-qmp-usb3-phy" must contain "phy", "common". + For "qcom,ipq8074-qmp-pcie-phy" must contain: + "phy", "common". - vdda-phy-supply: Phandle to a regulator supply to PHY core block. - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block. @@ -60,6 +63,13 @@ Required properties for child node: one for each entry in clock-names. - clock-names: Must contain following for pcie and usb qmp phys: "pipe<lane-number>" for pipe clock specific to each lane. + - clock-output-names: Name of the PHY clock that will be the parent for + the above pipe clock. + + For "qcom,ipq8074-qmp-pcie-phy": + - "pcie20_phy0_pipe_clk" Pipe Clock parent + (or) + "pcie20_phy1_pipe_clk" - resets: a list of phandles and reset controller specifier pairs, one for each entry in reset-names. @@ -96,6 +106,7 @@ Example: clocks = <&gcc GCC_PCIE_0_PIPE_CLK>; clock-names = "pipe0"; + clock-output-names = "pcie_0_pipe_clk_src"; resets = <&gcc GCC_PCIE_0_PHY_BCR>; reset-names = "lane0"; }; diff --git a/Documentation/devicetree/bindings/phy/ralink-usb-phy.txt b/Documentation/devicetree/bindings/phy/ralink-usb-phy.txt new file mode 100644 index 000000000000..9d2868a437ab --- /dev/null +++ b/Documentation/devicetree/bindings/phy/ralink-usb-phy.txt @@ -0,0 +1,23 @@ +Mediatek/Ralink USB PHY + +Required properties: + - compatible: "ralink,rt3352-usbphy" + "mediatek,mt7620-usbphy" + "mediatek,mt7628-usbphy" + - reg: required for "mediatek,mt7628-usbphy", unused otherwise + - #phy-cells: should be 0 + - ralink,sysctl: a phandle to a ralink syscon register region + - resets: the two reset controllers for host and device + - reset-names: the names of the 2 reset controllers + +Example: + +usbphy: phy { + compatible = "mediatek,mt7628-usbphy"; + reg = <0x10120000 0x1000>; + #phy-cells = <0>; + + ralink,sysctl = <&sysc>; + resets = <&rstctrl 22 &rstctrl 25>; + reset-names = "host", "device"; +}; diff --git a/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt index 0f6222a672ce..b496042f1f44 100644 --- a/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt +++ b/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt @@ -3,7 +3,6 @@ Rockchip PCIE PHY Required properties: - compatible: rockchip,rk3399-pcie-phy - - #phy-cells: must be 0 - clocks: Must contain an entry in clock-names. See ../clocks/clock-bindings.txt for details. - clock-names: Must be "refclk" @@ -11,6 +10,12 @@ Required properties: See ../reset/reset.txt for details. - reset-names: Must be "phy" +Required properties for legacy PHY mode (deprecated): + - #phy-cells: must be 0 + +Required properties for per-lane PHY mode (preferred): + - #phy-cells: must be 1 + Example: grf: syscon@ff770000 { diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt index ab80bfe31cb3..1c40ccd40ce4 100644 --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt @@ -82,7 +82,6 @@ usbphy: phy@125b0000 { reg = <0x125b0000 0x100>; clocks = <&clock 305>, <&clock 2>; clock-names = "phy", "ref"; - status = "okay"; #phy-cells = <1>; samsung,sysreg-phandle = <&sys_reg>; samsung,pmureg-phandle = <&pmu_reg>; diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt index 005bc22938ff..cbc7847dbf6c 100644 --- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt @@ -9,6 +9,7 @@ Required properties: * allwinner,sun7i-a20-usb-phy * allwinner,sun8i-a23-usb-phy * allwinner,sun8i-a33-usb-phy + * allwinner,sun8i-a83t-usb-phy * allwinner,sun8i-h3-usb-phy * allwinner,sun8i-v3s-usb-phy * allwinner,sun50i-a64-usb-phy @@ -17,18 +18,22 @@ Required properties: * "phy_ctrl" * "pmu0" for H3, V3s and A64 * "pmu1" - * "pmu2" for sun4i, sun6i or sun7i + * "pmu2" for sun4i, sun6i, sun7i, sun8i-a83t or sun8i-h3 + * "pmu3" for sun8i-h3 - #phy-cells : from the generic phy bindings, must be 1 - clocks : phandle + clock specifier for the phy clocks - clock-names : * "usb_phy" for sun4i, sun5i or sun7i * "usb0_phy", "usb1_phy" and "usb2_phy" for sun6i * "usb0_phy", "usb1_phy" for sun8i + * "usb0_phy", "usb1_phy", "usb2_phy" and "usb2_hsic_12M" for sun8i-a83t + * "usb0_phy", "usb1_phy", "usb2_phy" and "usb3_phy" for sun8i-h3 - resets : a list of phandle + reset specifier pairs - reset-names : * "usb0_reset" * "usb1_reset" - * "usb2_reset" for sun4i, sun6i or sun7i + * "usb2_reset" for sun4i, sun6i, sun7i, sun8i-a83t or sun8i-h3 + * "usb3_reset" for sun8i-h3 Optional properties: - usb0_id_det-gpios : gpio phandle for reading the otg id pin value @@ -37,6 +42,7 @@ Optional properties: - usb0_vbus-supply : regulator phandle for controller usb0 vbus - usb1_vbus-supply : regulator phandle for controller usb1 vbus - usb2_vbus-supply : regulator phandle for controller usb2 vbus +- usb3_vbus-supply : regulator phandle for controller usb3 vbus Example: usbphy: phy@0x01c13400 { diff --git a/Documentation/devicetree/bindings/phy/sun9i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun9i-usb-phy.txt index 1cca85c709d1..f9853156e311 100644 --- a/Documentation/devicetree/bindings/phy/sun9i-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/sun9i-usb-phy.txt @@ -33,6 +33,5 @@ Example: clock-names = "hsic_480M", "hsic_12M", "phy"; resets = <&usb_phy_clk 18>, <&usb_phy_clk 19>; reset-names = "hsic", "phy"; - status = "disabled"; #phy-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt index 590e60378be3..3e23fece99da 100644 --- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt @@ -148,5 +148,4 @@ dbgu: serial@fffff200 { interrupts = <1 4 7>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_dbgu>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt new file mode 100644 index 000000000000..61466c58faae --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt @@ -0,0 +1,59 @@ +Cortina Systems Gemini pin controller + +This pin controller is found in the Cortina Systems Gemini SoC family, +see further arm/gemini.txt. It is a purely group-based multiplexing pin +controller. + +The pin controller node must be a subnode of the system controller node. + +Required properties: +- compatible: "cortina,gemini-pinctrl" + +Subnodes of the pin controller contain pin control multiplexing set-up. +Please refer to pinctrl-bindings.txt for generic pin multiplexing nodes. + +Example: + + +syscon { + compatible = "cortina,gemini-syscon"; + ... + pinctrl { + compatible = "cortina,gemini-pinctrl"; + pinctrl-names = "default"; + pinctrl-0 = <&dram_default_pins>, <&system_default_pins>, + <&vcontrol_default_pins>; + + dram_default_pins: pinctrl-dram { + mux { + function = "dram"; + groups = "dramgrp"; + }; + }; + rtc_default_pins: pinctrl-rtc { + mux { + function = "rtc"; + groups = "rtcgrp"; + }; + }; + power_default_pins: pinctrl-power { + mux { + function = "power"; + groups = "powergrp"; + }; + }; + system_default_pins: pinctrl-system { + mux { + function = "system"; + groups = "systemgrp"; + }; + }; + (...) + uart_default_pins: pinctrl-uart { + mux { + function = "uart"; + groups = "uartrxtxgrp"; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt index 9fde25f1401a..42d74f8a1bcc 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt @@ -61,7 +61,6 @@ Examples: usdhc@0219c000 { /* uSDHC4 */ non-removable; vmmc-supply = <®_3p3v>; - status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usdhc4_1>; }; diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt index 8c5d27c5b562..6666277c3acb 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt @@ -61,7 +61,6 @@ iomuxc-lpsr controller and SDA pad from iomuxc controller as: i2c1: i2c@30a20000 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c1_1 &pinctrl_i2c1_2>; - status = "okay"; }; iomuxc-lpsr@302c0000 { diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7ulp-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7ulp-pinctrl.txt new file mode 100644 index 000000000000..44ad670ae11e --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7ulp-pinctrl.txt @@ -0,0 +1,61 @@ +* Freescale i.MX7ULP IOMUX Controller + +i.MX 7ULP has three IOMUXC instances: IOMUXC0 for M4 ports, IOMUXC1 for A7 +ports and IOMUXC DDR for DDR interface. + +Note: +This binding doc is only for the IOMUXC1 support in A7 Domain and it only +supports generic pin config. + +Please also refer pinctrl-bindings.txt in this directory for generic pinctrl +binding. + +=== Pin Controller Node === + +Required properties: +- compatible: "fsl,imx7ulp-iomuxc1" +- reg: Should contain the base physical address and size of the iomuxc + registers. + +=== Pin Configuration Node === +- pinmux: One integers array, represents a group of pins mux setting. + The format is pinmux = <PIN_FUNC_ID>, PIN_FUNC_ID is a pin working on + a specific function. + + NOTE: i.MX7ULP PIN_FUNC_ID consists of 4 integers as it shares one mux + and config register as follows: + <mux_conf_reg input_reg mux_mode input_val> + + Refer to imx7ulp-pinfunc.h in in device tree source folder for all + available imx7ulp PIN_FUNC_ID. + +Optional Properties: +- drive-strength Integer. Controls Drive Strength + 0: Standard + 1: Hi Driver +- drive-push-pull Bool. Enable Pin Push-pull +- drive-open-drain Bool. Enable Pin Open-drian +- slew-rate: Integer. Controls Slew Rate + 0: Standard + 1: Slow +- bias-disable: Bool. Pull disabled +- bias-pull-down: Bool. Pull down on pin +- bias-pull-up: Bool. Pull up on pin + +Examples: +#include "imx7ulp-pinfunc.h" + +/* Pin Controller Node */ +iomuxc1: iomuxc@40ac0000 { + compatible = "fsl,imx7ulp-iomuxc1"; + reg = <0x40ac0000 0x1000>; + + /* Pin Configuration Node */ + pinctrl_lpuart4: lpuart4grp { + pinmux = < + IMX7ULP_PAD_PTC3__LPUART4_RX + IMX7ULP_PAD_PTC2__LPUART4_TX + >; + bias-pull-up; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-dpaux-padctl.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-dpaux-padctl.txt index f2abdaee9022..e0e886b73527 100644 --- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-dpaux-padctl.txt +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-dpaux-padctl.txt @@ -56,5 +56,4 @@ Example: pinctrl-0 = <&state_dpaux_i2c>; pinctrl-1 = <&state_dpaux_off>; pinctrl-names = "default", "idle"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt index 09e81a95bbfd..b1159434f593 100644 --- a/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt @@ -50,7 +50,6 @@ uart2: serial@900000 { reg-io-width = <1>; current-speed = <115200>; no-loopback-test; - status = "disabled"; resets = <&reset 22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart2>; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt index ca01710ee29a..3b7266c7c438 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt @@ -69,8 +69,9 @@ PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 RGMII1 RGMII2 RMII1 RMII2 ROM16 ROM8 ROMCS1 ROMCS2 ROMCS3 ROMCS4 RXD1 RXD2 RXD3 RXD4 SALT1 SALT2 SALT3 SALT4 SD1 SD2 SGPMCK SGPMI SGPMLD SGPMO SGPSCK SGPSI0 SGPSI1 SGPSLD SIOONCTRL SIOPBI SIOPBO SIOPWREQ SIOPWRGD SIOS3 SIOS5 SIOSCI SPI1 SPI1DEBUG SPI1PASSTHRU SPICS1 TIMER3 TIMER4 -TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 TXD3 TXD4 UART6 USBCKI VGABIOS_ROM VGAHS -VGAVS VPI18 VPI24 VPI30 VPO12 VPO24 WDTRST1 WDTRST2 +TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 TXD3 TXD4 UART6 USB11D1 USB11H2 USB2D1 +USB2H1 USBCKI VGABIOS_ROM VGAHS VGAVS VPI18 VPI24 VPI30 VPO12 VPO24 WDTRST1 +WDTRST2 aspeed,ast2500-pinctrl, aspeed,g5-pinctrl: @@ -86,7 +87,8 @@ SALT11 SALT12 SALT13 SALT14 SALT2 SALT3 SALT4 SALT5 SALT6 SALT7 SALT8 SALT9 SCL1 SCL2 SD1 SD2 SDA1 SDA2 SGPS1 SGPS2 SIOONCTRL SIOPBI SIOPBO SIOPWREQ SIOPWRGD SIOS3 SIOS5 SIOSCI SPI1 SPI1CS1 SPI1DEBUG SPI1PASSTHRU SPI2CK SPI2CS0 SPI2CS1 SPI2MISO SPI2MOSI TIMER3 TIMER4 TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 -TXD3 TXD4 UART6 USBCKI VGABIOSROM VGAHS VGAVS VPI24 VPO WDTRST1 WDTRST2 +TXD3 TXD4 UART6 USB11BHID USB2AD USB2AH USB2BD USB2BH USBCKI VGABIOSROM VGAHS +VGAVS VPI24 VPO WDTRST1 WDTRST2 Examples ======== diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index 62d0f33fa65e..4483cc31e531 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -268,6 +268,8 @@ output-enable - enable output on a pin without actively driving it (such as enabling an output buffer) output-low - set the pin to output mode with low level output-high - set the pin to output mode with high level +sleep-hardware-state - indicate this is sleep related state which will be programmed + into the registers for the sleep state. slew-rate - set the slew rate For example: diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt index 17631d0a9af7..37d744750579 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt @@ -5,6 +5,7 @@ The Mediatek's Pin controller is used to control SoC pins. Required properties: - compatible: value should be one of the following. "mediatek,mt2701-pinctrl", compatible with mt2701 pinctrl. + "mediatek,mt2712-pinctrl", compatible with mt2712 pinctrl. "mediatek,mt6397-pinctrl", compatible with mt6397 pinctrl. "mediatek,mt7623-pinctrl", compatible with mt7623 pinctrl. "mediatek,mt8127-pinctrl", compatible with mt8127 pinctrl. diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-rk805.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-rk805.txt new file mode 100644 index 000000000000..eee3dc260934 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-rk805.txt @@ -0,0 +1,63 @@ +Pincontrol driver for RK805 Power management IC. + +RK805 has 2 pins which can be configured as GPIO output only. + +Please refer file <devicetree/bindings/pinctrl/pinctrl-bindings.txt> +for details of the common pinctrl bindings used by client devices, +including the meaning of the phrase "pin configuration node". + +Optional Pinmux properties: +-------------------------- +Following properties are required if default setting of pins are required +at boot. +- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>. +- pinctrl[0...n]: Properties to contain the phandle for pinctrl states per + <pinctrl-binding.txt>. + +The pin configurations are defined as child of the pinctrl states node. Each +sub-node have following properties: + +Required properties: +------------------ +- #gpio-cells: Should be two. The first cell is the pin number and the + second is the GPIO flags. + +- gpio-controller: Marks the device node as a GPIO controller. + +- pins: List of pins. Valid values of pins properties are: gpio0, gpio1. + +First 2 properties must be added in the RK805 PMIC node, documented in +Documentation/devicetree/bindings/mfd/rk808.txt + +Optional properties: +------------------- +Following are optional properties defined as pinmux DT binding document +<pinctrl-bindings.txt>. Absence of properties will leave the configuration +on default. + function, + output-low, + output-high. + +Valid values for function properties are: gpio. + +Theres is also not customised properties for any GPIO. + +Example: +-------- +rk805: rk805@18 { + compatible = "rockchip,rk805"; + ... + gpio-controller; + #gpio-cells = <2>; + + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int_l>, <&rk805_default>; + + rk805_default: pinmux { + gpio01 { + pins = "gpio0", "gpio1"; + function = "gpio"; + output-high; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-zx.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-zx.txt index e219849b21ca..39170f372599 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-zx.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-zx.txt @@ -81,5 +81,4 @@ pmm: pin-controller@1462000 { &vga { pinctrl-names = "default"; pinctrl-0 = <&vga_pins>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt index a7bde64798c7..a752a4716486 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt @@ -46,7 +46,8 @@ Valid values for pins are: gpio0-gpio89 Valid values for function are: - cam_mclk, codec_mic_i2s, codec_spkr_i2s, gpio, gsbi1, gsbi2, gsbi3, gsbi4, + cam_mclk, codec_mic_i2s, codec_spkr_i2s, gp_clk_0a, gp_clk_0b, gp_clk_1a, + gp_clk_1b, gp_clk_2a, gp_clk_2b, gpio, gsbi1, gsbi2, gsbi3, gsbi4, gsbi4_cam_i2c, gsbi5, gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, gsbi6_spi_cs1, gsbi6_spi_cs2, gsbi6_spi_cs3, gsbi7, gsbi7_spi_cs1, gsbi7_spi_cs2, gsbi7_spi_cs3, gsbi_cam_i2c, hdmi, mi2s, riva_bt, riva_fm, diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt index cfb8500dd56b..93374f478b9e 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt @@ -50,7 +50,11 @@ Valid values for qcom,pins are: Supports mux, bias and drive-strength Valid values for qcom,function are: -gpio, blsp_uart1, blsp_i2c0, blsp_i2c1, blsp_uart0, blsp_spi1, blsp_spi0 +aud_pin, audio_pwm, blsp_i2c0, blsp_i2c1, blsp_spi0, blsp_spi1, blsp_uart0, +blsp_uart1, chip_rst, gpio, i2s_rx, i2s_spdif_in, i2s_spdif_out, i2s_td, i2s_tx, +jtag, led0, led1, led2, led3, led4, led5, led6, led7, led8, led9, led10, led11, +mdc, mdio, pcie, pmu, prng_rosc, qpic, rgmii, rmii, sdio, smart0, smart1, +smart2, smart3, tm, wifi0, wifi1 Example: diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt index 8d893a874634..5b12c57e7f02 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt @@ -16,6 +16,7 @@ PMIC's from Qualcomm. "qcom,pm8941-gpio" "qcom,pm8994-gpio" "qcom,pma8084-gpio" + "qcom,pmi8994-gpio" And must contain either "qcom,spmi-gpio" or "qcom,ssbi-gpio" if the device is on an spmi bus or an ssbi bus respectively @@ -85,6 +86,7 @@ to specify in a pin configuration subnode: gpio1-gpio36 for pm8941 gpio1-gpio22 for pm8994 gpio1-gpio22 for pma8084 + gpio1-gpio10 for pmi8994 - function: Usage: required @@ -98,7 +100,10 @@ to specify in a pin configuration subnode: "dtest1", "dtest2", "dtest3", - "dtest4" + "dtest4", + And following values are supported by LV/MV GPIO subtypes: + "func3", + "func4" - bias-disable: Usage: optional @@ -183,6 +188,25 @@ to specify in a pin configuration subnode: Value type: <none> Definition: The specified pins are configured in open-source mode. +- qcom,analog-pass: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in analog-pass-through mode. + +- qcom,atest: + Usage: optional + Value type: <u32> + Definition: Selects ATEST rail to route to GPIO when it's configured + in analog-pass-through mode. + Valid values are 1-4 corresponding to ATEST1 to ATEST4. + +- qcom,dtest-buffer: + Usage: optional + Value type: <u32> + Definition: Selects DTEST rail to route to GPIO when it's configured + as digital input. + Valid values are 1-4 corresponding to DTEST1 to DTEST4. + Example: pm8921_gpio: gpio@150 { diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index 645082f03259..9b4f8041c36a 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -24,6 +24,7 @@ Required Properties: - "renesas,pfc-r8a7794": for R8A7794 (R-Car E2) compatible pin-controller. - "renesas,pfc-r8a7795": for R8A7795 (R-Car H3) compatible pin-controller. - "renesas,pfc-r8a7796": for R8A7796 (R-Car M3-W) compatible pin-controller. + - "renesas,pfc-r8a77995": for R8A77995 (R-Car D3) compatible pin-controller. - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller. - reg: Base address and length of each memory resource used by the pin @@ -111,7 +112,7 @@ Examples Example 1: SH73A0 (SH-Mobile AG5) pin controller node - pfc: pfc@e6050000 { + pfc: pin-controller@e6050000 { compatible = "renesas,pfc-sh73a0"; reg = <0xe6050000 0x8000>, <0xe605801c 0x1c>; @@ -172,5 +173,4 @@ Example 4: KZM-A9-GT (SH-Mobile AG5) default pin state for the MMCIF device bus-width = <8>; vmmc-supply = <®_1p8v>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt index ee01ab58224d..4864e3a74de3 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -24,6 +24,7 @@ Required properties for iomux controller: "rockchip,rk2928-pinctrl": for Rockchip RK2928 "rockchip,rk3066a-pinctrl": for Rockchip RK3066a "rockchip,rk3066b-pinctrl": for Rockchip RK3066b + "rockchip,rk3128-pinctrl": for Rockchip RK3128 "rockchip,rk3188-pinctrl": for Rockchip RK3188 "rockchip,rk3228-pinctrl": for Rockchip RK3228 "rockchip,rk3288-pinctrl": for Rockchip RK3288 @@ -120,7 +121,6 @@ uart2: serial@20064000 { reg-shift = <2>; reg-io-width = <1>; clocks = <&mux_uart2>; - status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&uart2_xfer>; diff --git a/Documentation/devicetree/bindings/pinctrl/sprd,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/sprd,pinctrl.txt new file mode 100644 index 000000000000..b1cea7a3a071 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/sprd,pinctrl.txt @@ -0,0 +1,83 @@ +* Spreadtrum Pin Controller + +The Spreadtrum pin controller are organized in 3 blocks (types). + +The first block comprises some global control registers, and each +register contains several bit fields with one bit or several bits +to configure for some global common configuration, such as domain +pad driving level, system control select and so on ("domain pad +driving level": One pin can output 3.0v or 1.8v, depending on the +related domain pad driving selection, if the related domain pad +slect 3.0v, then the pin can output 3.0v. "system control" is used +to choose one function (like: UART0) for which system, since we +have several systems (AP/CP/CM4) on one SoC.). + +There are too much various configuration that we can not list all +of them, so we can not make every Spreadtrum-special configuration +as one generic configuration, and maybe it will add more strange +global configuration in future. Then we add one "sprd,control" to +set these various global control configuration, and we need use +magic number for this property. + +Moreover we recognise every fields comprising one bit or several +bits in one global control register as one pin, thus we should +record every pin's bit offset, bit width and register offset to +configure this field (pin). + +The second block comprises some common registers which have unified +register definition, and each register described one pin is used +to configure the pin sleep mode, function select and sleep related +configuration. + +Now we have 4 systems for sleep mode on SC9860 SoC: AP system, +PUBCP system, TGLDSP system and AGDSP system. And the pin sleep +related configuration are: +- input-enable +- input-disable +- output-high +- output-low +- bias-pull-up +- bias-pull-down + +In some situation we need set the pin sleep mode and pin sleep related +configuration, to set the pin sleep related configuration automatically +by hardware when the system specified by sleep mode goes into deep +sleep mode. For example, if we set the pin sleep mode as PUBCP_SLEEP +and set the pin sleep related configuration as "input-enable", which +means when PUBCP system goes into deep sleep mode, this pin will be set +input enable automatically. + +Moreover we can not use the "sleep" state, since some systems (like: +PUBCP system) do not run linux kernel OS (only AP system run linux +kernel on SC9860 platform), then we can not select "sleep" state +when the PUBCP system goes into deep sleep mode. Thus we introduce +"sprd,sleep-mode" property to set pin sleep mode. + +The last block comprises some misc registers which also have unified +register definition, and each register described one pin is used to +configure drive strength, pull up/down and so on. Especially for pull +up, we have two kind pull up resistor: 20K and 4.7K. + +Required properties for Spreadtrum pin controller: +- compatible: "sprd,<soc>-pinctrl" + Please refer to each sprd,<soc>-pinctrl.txt binding doc for supported SoCs. +- reg: The register address of pin controller device. +- pins : An array of pin names. + +Optional properties: +- function: Specified the function name. +- drive-strength: Drive strength in mA. +- input-schmitt-disable: Enable schmitt-trigger mode. +- input-schmitt-enable: Disable schmitt-trigger mode. +- bias-disable: Disable pin bias. +- bias-pull-down: Pull down on pin. +- bias-pull-up: Pull up on pin. +- input-enable: Enable pin input. +- input-disable: Enable pin output. +- output-high: Set the pin as an output level high. +- output-low: Set the pin as an output level low. +- sleep-hardware-state: Indicate these configs in this state are sleep related. +- sprd,control: Control values referring to databook for global control pins. +- sprd,sleep-mode: Sleep mode selection. + +Please refer to each sprd,<soc>-pinctrl.txt binding doc for supported values. diff --git a/Documentation/devicetree/bindings/pinctrl/sprd,sc9860-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/sprd,sc9860-pinctrl.txt new file mode 100644 index 000000000000..5a628333d52f --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/sprd,sc9860-pinctrl.txt @@ -0,0 +1,70 @@ +* Spreadtrum SC9860 Pin Controller + +Please refer to sprd,pinctrl.txt in this directory for common binding part +and usage. + +Required properties: +- compatible: Must be "sprd,sc9860-pinctrl". +- reg: The register address of pin controller device. +- pins : An array of strings, each string containing the name of a pin. + +Optional properties: +- function: A string containing the name of the function, values must be + one of: "func1", "func2", "func3" and "func4". +- drive-strength: Drive strength in mA. Supported values: 2, 4, 6, 8, 10, + 12, 14, 16, 20, 21, 24, 25, 27, 29, 31 and 33. +- input-schmitt-disable: Enable schmitt-trigger mode. +- input-schmitt-enable: Disable schmitt-trigger mode. +- bias-disable: Disable pin bias. +- bias-pull-down: Pull down on pin. +- bias-pull-up: Pull up on pin. Supported values: 20000 for pull-up resistor + is 20K and 4700 for pull-up resistor is 4.7K. +- input-enable: Enable pin input. +- input-disable: Enable pin output. +- output-high: Set the pin as an output level high. +- output-low: Set the pin as an output level low. +- sleep-hardware-state: Indicate these configs in this state are sleep related. +- sprd,control: Control values referring to databook for global control pins. +- sprd,sleep-mode: Choose the pin sleep mode, and supported values are: + AP_SLEEP, PUBCP_SLEEP, TGLDSP_SLEEP and AGDSP_SLEEP. + +Pin sleep mode definition: +enum pin_sleep_mode { + AP_SLEEP = BIT(0), + PUBCP_SLEEP = BIT(1), + TGLDSP_SLEEP = BIT(2), + AGDSP_SLEEP = BIT(3), +}; + +Example: +pin_controller: pinctrl@402a0000 { + compatible = "sprd,sc9860-pinctrl"; + reg = <0x402a0000 0x10000>; + + grp1: sd0 { + pins = "SC9860_VIO_SD2_IRTE", "SC9860_VIO_SD0_IRTE"; + sprd,control = <0x1>; + }; + + grp2: rfctl_33 { + pins = "SC9860_RFCTL33"; + function = "func2"; + sprd,sleep-mode = <AP_SLEEP | PUBCP_SLEEP>; + grp2_sleep_mode: rfctl_33_sleep { + pins = "SC9860_RFCTL33"; + sleep-hardware-state; + output-low; + } + }; + + grp3: rfctl_misc_20 { + pins = "SC9860_RFCTL20_MISC"; + drive-strength = <10>; + bias-pull-up = <4700>; + grp3_sleep_mode: rfctl_misc_sleep { + pins = "SC9860_RFCTL20_MISC"; + sleep-hardware-state; + bias-pull-up; + } + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt index d907a74f8dc0..33e3d3c47552 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -180,5 +180,4 @@ pin-controller { &usart1 { pinctrl-0 = <&usart1_pins_a>; pinctrl-names = "default"; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/power/power-controller.txt b/Documentation/devicetree/bindings/power/power-controller.txt index 4f7a3bc9c407..e45affea8078 100644 --- a/Documentation/devicetree/bindings/power/power-controller.txt +++ b/Documentation/devicetree/bindings/power/power-controller.txt @@ -13,6 +13,5 @@ Example: act8846: act8846@5 { compatible = "active-semi,act8846"; - status = "okay"; system-power-controller; } diff --git a/Documentation/devicetree/bindings/power/renesas,apmu.txt b/Documentation/devicetree/bindings/power/renesas,apmu.txt index 84404c9edff7..af21502e939c 100644 --- a/Documentation/devicetree/bindings/power/renesas,apmu.txt +++ b/Documentation/devicetree/bindings/power/renesas,apmu.txt @@ -1,12 +1,13 @@ DT bindings for the Renesas Advanced Power Management Unit -Renesas R-Car line of SoCs utilize one or more APMU hardware units +Renesas R-Car and RZ/G1 SoCs utilize one or more APMU hardware units for CPU core power domain control including SMP boot and CPU Hotplug. Required properties: - compatible: Should be "renesas,<soctype>-apmu", "renesas,apmu" as fallback. Examples with soctypes are: + - "renesas,r8a7743-apmu" (RZ/G1M) - "renesas,r8a7790-apmu" (R-Car H2) - "renesas,r8a7791-apmu" (R-Car M2-W) - "renesas,r8a7792-apmu" (R-Car V2H) diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt index d91715bc8d52..98cc8c09d02d 100644 --- a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt +++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt @@ -17,6 +17,7 @@ Required properties: - "renesas,r8a7794-sysc" (R-Car E2) - "renesas,r8a7795-sysc" (R-Car H3) - "renesas,r8a7796-sysc" (R-Car M3-W) + - "renesas,r8a77995-sysc" (R-Car D3) - reg: Address start and address range for the device. - #power-domain-cells: Must be 1. diff --git a/Documentation/devicetree/bindings/power/reset/st-reset.txt b/Documentation/devicetree/bindings/power/reset/st-reset.txt index 83734dc3a389..b63948737d80 100644 --- a/Documentation/devicetree/bindings/power/reset/st-reset.txt +++ b/Documentation/devicetree/bindings/power/reset/st-reset.txt @@ -8,5 +8,4 @@ Example node: restart { compatible = "st,stih407-restart"; st,syscfg = <&syscfg_sbc_reg>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt index 43c21fb04564..4a4766e9c254 100644 --- a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt +++ b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt @@ -39,6 +39,8 @@ Required properties: - "rockchip,rk3368-pmu-io-voltage-domain" for rk3368 pmu-domains - "rockchip,rk3399-io-voltage-domain" for rk3399 - "rockchip,rk3399-pmu-io-voltage-domain" for rk3399 pmu-domains + - "rockchip,rv1108-io-voltage-domain" for rv1108 + - "rockchip,rv1108-pmu-io-voltage-domain" for rv1108 pmu-domains Deprecated properties: - rockchip,grf: phandle to the syscon managing the "general register files" diff --git a/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt b/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt index de78d761ce44..b86ecada4f84 100644 --- a/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt +++ b/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt @@ -29,7 +29,6 @@ Example: pmic@5b { compatible = "active-semi,act8945a"; reg = <0x5b>; - status = "okay"; charger { compatible = "active-semi,act8945a-charger"; @@ -43,6 +42,5 @@ Example: active-semi,input-voltage-threshold-microvolt = <6600>; active-semi,precondition-timeout = <40>; active-semi,total-timeout = <3>; - status = "okay"; }; }; diff --git a/Documentation/devicetree/bindings/power/supply/bq24190.txt b/Documentation/devicetree/bindings/power/supply/bq24190.txt new file mode 100644 index 000000000000..9e517d307070 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq24190.txt @@ -0,0 +1,51 @@ +TI BQ24190 Li-Ion Battery Charger + +Required properties: +- compatible: contains one of the following: + * "ti,bq24190" + * "ti,bq24192i" +- reg: integer, I2C address of the charger. +- interrupts[-extended]: configuration for charger INT pin. + +Optional properties: +- monitored-battery: phandle of battery characteristics devicetree node + The charger uses the following battery properties: + + precharge-current-microamp: maximum charge current during precharge + phase (typically 20% of battery capacity). + + charge-term-current-microamp: a charge cycle terminates when the + battery voltage is above recharge threshold, and the current is below + this setting (typically 10% of battery capacity). + See also Documentation/devicetree/bindings/power/supply/battery.txt +- ti,system-minimum-microvolt: when power is connected and the battery is below + minimum system voltage, the system will be regulated above this setting. + +Notes: +- Some circuit boards wire the chip's "OTG" pin high (enabling 500mA default + charge current on USB SDP ports, among other features). To simulate this on + boards that wire the pin to a GPIO, set a gpio-hog. + +Example: + + bat: battery { + compatible = "simple-battery"; + precharge-current-microamp = <256000>; + charge-term-current-microamp = <128000>; + // etc. + }; + + bq24190: charger@6a { + compatible = "ti,bq24190"; + reg = <0x6a>; + interrupts-extended = <&gpiochip 10 IRQ_TYPE_EDGE_FALLING>; + monitored-battery = <&bat>; + ti,system-minimum-microvolt = <3200000>; + }; + + &twl_gpio { + otg { + gpio-hog; + gpios = <6 0>; + output-high; + line-name = "otg-gpio"; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/ltc2941.txt b/Documentation/devicetree/bindings/power/supply/ltc2941.txt index a9d7aa60558b..3b9ba147b041 100644 --- a/Documentation/devicetree/bindings/power/supply/ltc2941.txt +++ b/Documentation/devicetree/bindings/power/supply/ltc2941.txt @@ -1,13 +1,14 @@ -binding for LTC2941 and LTC2943 battery gauges +binding for LTC2941, LTC2942, LTC2943 and LTC2944 battery gauges -Both the LTC2941 and LTC2943 measure battery capacity. -The LTC2943 is compatible with the LTC2941, it adds voltage and -temperature monitoring, and uses a slightly different conversion -formula for the charge counter. +All chips measure battery capacity. +The LTC2942 is pin compatible with the LTC2941, it adds voltage and +temperature monitoring, and is runtime detected. LTC2943 and LTC2944 +is software compatible, uses a slightly different conversion formula +for the charge counter and adds voltage, current and temperature monitoring. Required properties: -- compatible: Should contain "lltc,ltc2941" or "lltc,ltc2943" which also - indicates the type of I2C chip attached. +- compatible: Should contain "lltc,ltc2941", "lltc,ltc2942", "lltc,ltc2943" + or "lltc,ltc2944" which also indicates the type of I2C chip attached. - reg: The 7-bit I2C address. - lltc,resistor-sense: The sense resistor value in milli-ohms. Can be a 32-bit negative value when the battery has been connected to the wrong end of the diff --git a/Documentation/devicetree/bindings/power/supply/max8903-charger.txt b/Documentation/devicetree/bindings/power/supply/max8903-charger.txt index f0f4e12b076e..bab947fef025 100644 --- a/Documentation/devicetree/bindings/power/supply/max8903-charger.txt +++ b/Documentation/devicetree/bindings/power/supply/max8903-charger.txt @@ -21,5 +21,4 @@ Example: flt-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; chg-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; cen-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt b/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt index e03e85ae6572..d6e8dfd0a581 100644 --- a/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt +++ b/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt @@ -12,7 +12,6 @@ Example: clock-frequency = <50000>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c2>; - status = "okay"; max14656@35 { compatible = "maxim,max14656"; diff --git a/Documentation/devicetree/bindings/power/wakeup-source.txt b/Documentation/devicetree/bindings/power/wakeup-source.txt index 963c6dfd484d..3c81f78b5c27 100644 --- a/Documentation/devicetree/bindings/power/wakeup-source.txt +++ b/Documentation/devicetree/bindings/power/wakeup-source.txt @@ -20,13 +20,12 @@ List of legacy properties and respective binding document 1. "enable-sdio-wakeup" Documentation/devicetree/bindings/mmc/mmc.txt 2. "gpio-key,wakeup" Documentation/devicetree/bindings/input/gpio-keys{,-polled}.txt 3. "has-tpo" Documentation/devicetree/bindings/rtc/rtc-opal.txt -4. "isil,irq2-can-wakeup-machine" Documentation/devicetree/bindings/rtc/isil,isl12057.txt -5. "linux,wakeup" Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt +4. "linux,wakeup" Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt Documentation/devicetree/bindings/mfd/tc3589x.txt Documentation/devicetree/bindings/input/ads7846.txt -6. "linux,keypad-wakeup" Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt -7. "linux,input-wakeup" Documentation/devicetree/bindings/input/samsung-keypad.txt -8. "nvidia,wakeup-source" Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt +5. "linux,keypad-wakeup" Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt +6. "linux,input-wakeup" Documentation/devicetree/bindings/input/samsung-keypad.txt +7. "nvidia,wakeup-source" Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt Examples -------- diff --git a/Documentation/devicetree/bindings/powerpc/ibm,vas.txt b/Documentation/devicetree/bindings/powerpc/ibm,vas.txt new file mode 100644 index 000000000000..bf11d2faf7b8 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/ibm,vas.txt @@ -0,0 +1,22 @@ +* IBM Powerpc Virtual Accelerator Switchboard (VAS) + +VAS is a hardware mechanism that allows kernel subsystems and user processes +to directly submit compression and other requests to Nest accelerators (NX) +or other coprocessors functions. + +Required properties: +- compatible : should be "ibm,vas". +- ibm,vas-id : A unique identifier for each instance of VAS in the system +- reg : Should contain 4 pairs of 64-bit fields specifying the Hypervisor + window context start and length, OS/User window context start and length, + "Paste address" start and length, "Paste window id" start bit and number + of bits) + +Example: + + vas@6019100000000 { + compatible = "ibm,vas", "ibm,power9-vas"; + reg = <0x6019100000000 0x2000000 0x6019000000000 0x100000000 0x8000000000000 0x100000000 0x20 0x10>; + name = "vas"; + ibm,vas-id = <0x1>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/opal/sensor-groups.txt b/Documentation/devicetree/bindings/powerpc/opal/sensor-groups.txt new file mode 100644 index 000000000000..6ad881cbffda --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/opal/sensor-groups.txt @@ -0,0 +1,27 @@ +IBM OPAL Sensor Groups Binding +------------------------------- + +Node: /ibm,opal/sensor-groups + +Description: Contains sensor groups available in the Powernv P9 +servers. Each child node indicates a sensor group. + +- compatible : Should be "ibm,opal-sensor-group" + +Each child node contains below properties: + +- type : String to indicate the type of sensor-group + +- sensor-group-id: Abstract unique identifier provided by firmware of + type <u32> which is used for sensor-group + operations like clearing the min/max history of all + sensors belonging to the group. + +- ibm,chip-id : Chip ID + +- sensors : Phandle array of child nodes of /ibm,opal/sensor/ + belonging to this group + +- ops : Array of opal-call numbers indicating available operations on + sensor groups like clearing min/max, enabling/disabling sensor + group. diff --git a/Documentation/devicetree/bindings/pps/pps-gpio.txt b/Documentation/devicetree/bindings/pps/pps-gpio.txt index 40bf9c3564a5..0de23b793657 100644 --- a/Documentation/devicetree/bindings/pps/pps-gpio.txt +++ b/Documentation/devicetree/bindings/pps/pps-gpio.txt @@ -13,8 +13,12 @@ Optional properties: Example: pps { - compatible = "pps-gpio"; - gpios = <&gpio2 6 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pps>; + gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>; assert-falling-edge; + + compatible = "pps-gpio"; + status = "okay"; }; diff --git a/Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt b/Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt index 7c04e22a5d6a..6b1075ee8a30 100644 --- a/Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt +++ b/Documentation/devicetree/bindings/ptp/brcm,ptp-dte.txt @@ -16,5 +16,4 @@ Example: ptp: ptp-dte@180af650 { compatible = "brcm,iproc-ptp-dte", "brcm,ptp-dte"; reg = <0x180af650 0x10>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt index cf573e85b11d..8cf87d1bfca5 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt @@ -6,7 +6,7 @@ Required properties: - clocks: This clock defines the base clock frequency of the PWM hardware system, the period and the duty_cycle of the PWM signal is a multiple of the base period. -- #pwm-cells: Should be 2. See pwm.txt in this directory for a description of +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of the cells format. Examples: @@ -15,7 +15,7 @@ pwm@2020c000 { compatible = "brcm,bcm2835-pwm"; reg = <0x2020c000 0x28>; clocks = <&clk_pwm>; - #pwm-cells = <2>; + #pwm-cells = <3>; }; clocks { diff --git a/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt index 54c59b0560ad..ef8bd3cb67ab 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt @@ -2,6 +2,8 @@ MediaTek PWM controller Required properties: - compatible: should be "mediatek,<name>-pwm": + - "mediatek,mt2712-pwm": found on mt2712 SoC. + - "mediatek,mt7622-pwm": found on mt7622 SoC. - "mediatek,mt7623-pwm": found on mt7623 SoC. - reg: physical base address and length of the controller's registers. - #pwm-cells: must be 2. See pwm.txt in this directory for a description of @@ -10,7 +12,9 @@ Required properties: - clock-names: must contain the following: - "top": the top clock generator - "main": clock used by the PWM core - - "pwm1-5": the five per PWM clocks + - "pwm1-8": the eight per PWM clocks for mt2712 + - "pwm1-6": the six per PWM clocks for mt7622 + - "pwm1-5": the five per PWM clocks for mt7623 - pinctrl-names: Must contain a "default" entry. - pinctrl-0: One property must exist for each entry in pinctrl-names. See pinctrl/pinctrl-bindings.txt for details of the property values. diff --git a/Documentation/devicetree/bindings/pwm/pwm-meson.txt b/Documentation/devicetree/bindings/pwm/pwm-meson.txt index 5b07bebbf6f7..1ee81321c35e 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-meson.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-meson.txt @@ -19,7 +19,6 @@ Example: compatible = "amlogic,meson-gxbb-pwm"; reg = <0x0 0x08550 0x0 0x10>; #pwm-cells = <3>; - status = "disabled"; clocks = <&xtal>, <&xtal>; clock-names = "clkin0", "clkin1"; } diff --git a/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt index b8be3d09ee26..2c5e52a5bede 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt @@ -3,10 +3,17 @@ Rockchip PWM controller Required properties: - compatible: should be "rockchip,<name>-pwm" "rockchip,rk2928-pwm": found on RK29XX,RK3066 and RK3188 SoCs - "rockchip,rk3288-pwm": found on RK3288 SoC + "rockchip,rk3288-pwm": found on RK3288 SOC + "rockchip,rv1108-pwm", "rockchip,rk3288-pwm": found on RV1108 SoC "rockchip,vop-pwm": found integrated in VOP on RK3288 SoC - reg: physical base address and length of the controller's registers - - clocks: phandle and clock specifier of the PWM reference clock + - clocks: See ../clock/clock-bindings.txt + - For older hardware (rk2928, rk3066, rk3188, rk3228, rk3288, rk3399): + - There is one clock that's used both to derive the functional clock + for the device and as the bus clock. + - For newer hardware (rk3328 and future socs): specified by name + - "pwm": This is used to derive the functional clock. + - "pclk": This is the APB bus clock. - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.txt in this directory for a description of the cell format. diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt new file mode 100644 index 000000000000..f8338d11fd2b --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt @@ -0,0 +1,24 @@ +STMicroelectronics STM32 Low-Power Timer PWM + +STM32 Low-Power Timer provides single channel PWM. + +Must be a sub-node of an STM32 Low-Power Timer device tree node. +See ../mfd/stm32-lptimer.txt for details about the parent node. + +Required parameters: +- compatible: Must be "st,stm32-pwm-lp". + +Optional properties: +- pinctrl-names: Set to "default". +- pinctrl-0: Phandle pointing to pin configuration node for PWM. + +Example: + timer@40002400 { + compatible = "st,stm32-lptimer"; + ... + pwm { + compatible = "st,stm32-pwm-lp"; + pinctrl-names = "default"; + pinctrl-0 = <&lppwm1_pins>; + }; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt index f1cbeefb3087..c5171660eaf9 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt @@ -19,5 +19,4 @@ Example: reg = <0x01c20e00 0xc>; clocks = <&osc24M>; #pwm-cells = <3>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt index 8007e839a716..06a363d9ccef 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt @@ -6,6 +6,7 @@ Required properties: for am4372 - compatible = "ti,am4372-ecap", "ti,am3352-ecap", "ti,am33xx-ecap"; for da850 - compatible = "ti,da850-ecap", "ti,am3352-ecap", "ti,am33xx-ecap"; for dra746 - compatible = "ti,dra746-ecap", "ti,am3352-ecap"; + for 66ak2g - compatible = "ti,k2g-ecap", "ti,am3352-ecap"; - #pwm-cells: should be 3. See pwm.txt in this directory for a description of the cells format. The PWM channel index ranges from 0 to 4. The only third cell flag supported by this binding is PWM_POLARITY_INVERTED. diff --git a/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt index 1a5d7b71db89..4633697fbda1 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt @@ -26,7 +26,6 @@ epwmss0: epwmss@48300000 { /* PWMSS for am33xx */ ti,hwmods = "epwmss0"; #address-cells = <1>; #size-cells = <1>; - status = "disabled"; ranges = <0x48300100 0x48300100 0x80 /* ECAP */ 0x48300180 0x48300180 0x80 /* EQEP */ 0x48300200 0x48300200 0x80>; /* EHRPWM */ @@ -40,7 +39,6 @@ epwmss0: epwmss@48300000 { /* PWMSS for am4372 */ ti,hwmods = "epwmss0"; #address-cells = <1>; #size-cells = <1>; - status = "disabled"; ranges = <0x48300100 0x48300100 0x80 /* ECAP */ 0x48300180 0x48300180 0x80 /* EQEP */ 0x48300200 0x48300200 0x80>; /* EHRPWM */ diff --git a/Documentation/devicetree/bindings/pwm/pwm-zx.txt b/Documentation/devicetree/bindings/pwm/pwm-zx.txt new file mode 100644 index 000000000000..a6bcc75c9164 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-zx.txt @@ -0,0 +1,22 @@ +ZTE ZX PWM controller + +Required properties: + - compatible: Should be "zte,zx296718-pwm". + - reg: Physical base address and length of the controller's registers. + - clocks : The phandle and specifier referencing the controller's clocks. + - clock-names: "pclk" for PCLK, "wclk" for WCLK to the PWM controller. The + PCLK is for register access, while WCLK is the reference clock for + calculating period and duty cycles. + - #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + the cells format. + +Example: + + pwm: pwm@1439000 { + compatible = "zte,zx296718-pwm"; + reg = <0x1439000 0x1000>; + clocks = <&lsp1crm LSP1_PWM_PCLK>, + <&lsp1crm LSP1_PWM_WCLK>; + clock-names = "pclk", "wclk"; + #pwm-cells = <3>; + }; diff --git a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt index b067e84a94b5..1aadc804dae4 100644 --- a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt @@ -6,7 +6,6 @@ Required Properties: - "renesas,tpu-r8a73a4": for R8A77A4 (R-Mobile APE6) compatible PWM controller. - "renesas,tpu-r8a7740": for R8A7740 (R-Mobile A1) compatible PWM controller. - "renesas,tpu-r8a7790": for R8A7790 (R-Car H2) compatible PWM controller. - - "renesas,tpu-sh7372": for SH7372 (SH-Mobile AP4) compatible PWM controller. - "renesas,tpu": for generic R-Car TPU PWM controller. - reg: Base address and length of each memory resource used by the PWM diff --git a/Documentation/devicetree/bindings/regulator/act8865-regulator.txt b/Documentation/devicetree/bindings/regulator/act8865-regulator.txt index 6067d9830d07..3ae9f1088845 100644 --- a/Documentation/devicetree/bindings/regulator/act8865-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/act8865-regulator.txt @@ -52,7 +52,6 @@ Example: compatible = "active-semi,act8865"; reg = <0x5b>; active-semi,vsel-high; - status = "disabled"; regulators { vcc_1v8_reg: DCDC_REG1 { diff --git a/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt index 5c80a7779552..ac955dea00d1 100644 --- a/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt @@ -23,7 +23,6 @@ Example: pmic@5b { compatible = "active-semi,act8945a"; reg = <0x5b>; - status = "okay"; active-semi,vsel-high; diff --git a/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt index 02649d8b3f5a..84d544d8c1b1 100644 --- a/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt @@ -1,4 +1,4 @@ -Mediatek MT6311 Regulator Driver +Mediatek MT6311 Regulator Required properties: - compatible: "mediatek,mt6311-regulator" diff --git a/Documentation/devicetree/bindings/regulator/mt6323-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6323-regulator.txt index c35d878b0960..a48749db4df3 100644 --- a/Documentation/devicetree/bindings/regulator/mt6323-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/mt6323-regulator.txt @@ -1,4 +1,4 @@ -Mediatek MT6323 Regulator Driver +Mediatek MT6323 Regulator All voltage regulators are defined as subnodes of the regulators node. A list of regulators provided by this controller are defined as subnodes of the diff --git a/Documentation/devicetree/bindings/regulator/mt6380-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6380-regulator.txt new file mode 100644 index 000000000000..0058441f16d2 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/mt6380-regulator.txt @@ -0,0 +1,89 @@ +MediaTek MT6380 Regulator + +All voltage regulators provided by the MT6380 PMIC are described as the +subnodes of the MT6380 regulators node. Each regulator is named according +to its regulator type, buck-<name> and ldo-<name>. The definition for each +of these nodes is defined using the standard binding for regulators at +Documentation/devicetree/bindings/regulator/regulator.txt. + +The valid names for regulators are: +BUCK: + buck-core1, buck-vcore, buck-vrf +LDO: + ldo-vm ,ldo-va , ldo-vphy, ldo-vddr, ldo-vt + +Example: + + regulators { + compatible = "mediatek,mt6380-regulator"; + + mt6380_vcpu_reg: buck-vcore1 { + regulator-name = "vcore1"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1393750>; + regulator-ramp-delay = <6250>; + regulator-always-on; + regulator-boot-on; + }; + + mt6380_vcore_reg: buck-vcore { + regulator-name = "vcore"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1393750>; + regulator-ramp-delay = <6250>; + }; + + mt6380_vrf_reg: buck-vrf { + regulator-name = "vrf"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1575000>; + regulator-ramp-delay = <0>; + regulator-always-on; + regulator-boot-on; + }; + + mt6380_vm_reg: ldo-vm { + regulator-name = "vm"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1400000>; + regulator-ramp-delay = <0>; + regulator-always-on; + regulator-boot-on; + }; + + mt6380_va_reg: ldo-va { + regulator-name = "va"; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <3300000>; + regulator-ramp-delay = <0>; + regulator-always-on; + regulator-boot-on; + }; + + mt6380_vphy_reg: ldo-vphy { + regulator-name = "vphy"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-ramp-delay = <0>; + regulator-always-on; + regulator-boot-on; + }; + + mt6380_vddr_reg: ldo-vddr { + regulator-name = "vddr"; + regulator-min-microvolt = <1240000>; + regulator-max-microvolt = <1840000>; + regulator-ramp-delay = <0>; + regulator-always-on; + regulator-boot-on; + }; + + mt6380_vt_reg: ldo-vt { + regulator-name = "vt"; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <3300000>; + regulator-ramp-delay = <0>; + regulator-always-on; + regulator-boot-on; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt index a42b1d6e9863..01141fb00875 100644 --- a/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt @@ -1,4 +1,4 @@ -Mediatek MT6397 Regulator Driver +Mediatek MT6397 Regulator Required properties: - compatible: "mediatek,mt6397-regulator" diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt index bf85aa9ad6a7..3d78d507e29f 100644 --- a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt @@ -71,7 +71,7 @@ Continuous Voltage With Enable GPIO Example: * Inverted PWM logic, and the duty cycle range is limited * to 30%-70%. */ - pwm-dutycycle-range <700 300>; /* */ + pwm-dutycycle-range = <700 300>; /* */ }; Voltage Table Example: diff --git a/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.txt b/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.txt new file mode 100644 index 000000000000..3944ee3e731e --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.txt @@ -0,0 +1,20 @@ +STM32 VREFBUF - Voltage reference buffer + +Some STM32 devices embed a voltage reference buffer which can be used as +voltage reference for ADCs, DACs and also as voltage reference for external +components through the dedicated VREF+ pin. + +Required properties: +- compatible: Must be "st,stm32-vrefbuf". +- reg: Offset and length of VREFBUF register set. +- clocks: Must contain an entry for peripheral clock. + +Example: + vrefbuf: regulator@58003C00 { + compatible = "st,stm32-vrefbuf"; + reg = <0x58003C00 0x8>; + clocks = <&rcc VREF_CK>; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2500000>; + vdda-supply = <&vdda>; + }; diff --git a/Documentation/devicetree/bindings/remoteproc/imx-rproc.txt b/Documentation/devicetree/bindings/remoteproc/imx-rproc.txt new file mode 100644 index 000000000000..fbcefd965dc4 --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/imx-rproc.txt @@ -0,0 +1,33 @@ +NXP iMX6SX/iMX7D Co-Processor Bindings +---------------------------------------- + +This binding provides support for ARM Cortex M4 Co-processor found on some +NXP iMX SoCs. + +Required properties: +- compatible Should be one of: + "fsl,imx7d-cm4" + "fsl,imx6sx-cm4" +- clocks Clock for co-processor (See: ../clock/clock-bindings.txt) +- syscon Phandle to syscon block which provide access to + System Reset Controller + +Optional properties: +- memory-region list of phandels to the reserved memory regions. + (See: ../reserved-memory/reserved-memory.txt) + +Example: + m4_reserved_sysmem1: cm4@80000000 { + reg = <0x80000000 0x80000>; + }; + + m4_reserved_sysmem2: cm4@81000000 { + reg = <0x81000000 0x80000>; + }; + + imx7d-cm4 { + compatible = "fsl,imx7d-cm4"; + memory-region = <&m4_reserved_sysmem1>, <&m4_reserved_sysmem2>; + syscon = <&src>; + clocks = <&clks IMX7D_ARM_M4_ROOT_CLK>; + }; diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt index 75ad7b8df0b1..728e4193f7a6 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt @@ -63,9 +63,10 @@ on the Qualcomm ADSP Hexagon core. = SUBNODES -The adsp node may have an subnode named "smd-edge" that describes the SMD edge, -channels and devices related to the ADSP. See ../soc/qcom/qcom,smd.txt for -details on how to describe the SMD edge. +The adsp node may have an subnode named either "smd-edge" or "glink-edge" that +describes the communication edge, channels and devices related to the ADSP. +See ../soc/qcom/qcom,smd.txt and ../soc/qcom/qcom,glink.txt for details on how +to describe these. = EXAMPLE diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt index 92347fe6890e..7ff3f7903f26 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt @@ -90,6 +90,11 @@ the memory regions used by the Hexagon firmware. Each sub-node must contain: Value type: <phandle> Definition: reference to the reserved-memory for the region +The Hexagon node may also have an subnode named either "smd-edge" or +"glink-edge" that describes the communication edge, channels and devices +related to the Hexagon. See ../soc/qcom/qcom,smd.txt and +../soc/qcom/qcom,glink.txt for details on how to describe these. + = EXAMPLE The following example describes the resources needed to boot control the Hexagon, as it is found on MSM8974 boards. diff --git a/Documentation/devicetree/bindings/remoteproc/ti,davinci-rproc.txt b/Documentation/devicetree/bindings/remoteproc/ti,davinci-rproc.txt new file mode 100644 index 000000000000..e44a97e21164 --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/ti,davinci-rproc.txt @@ -0,0 +1,86 @@ +TI Davinci DSP devices +======================= + +Binding status: Unstable - Subject to changes for DT representation of clocks + and resets + +The TI Davinci family of SoCs usually contains a TI DSP Core sub-system that +is used to offload some of the processor-intensive tasks or algorithms, for +achieving various system level goals. + +The processor cores in the sub-system usually contain additional sub-modules +like L1 and/or L2 caches/SRAMs, an Interrupt Controller, an external memory +controller, a dedicated local power/sleep controller etc. The DSP processor +core used in Davinci SoCs is usually a C674x DSP CPU. + +DSP Device Node: +================ +Each DSP Core sub-system is represented as a single DT node. + +Required properties: +-------------------- +The following are the mandatory properties: + +- compatible: Should be one of the following, + "ti,da850-dsp" for DSPs on OMAP-L138 SoCs + +- reg: Should contain an entry for each value in 'reg-names'. + Each entry should have the memory region's start address + and the size of the region, the representation matching + the parent node's '#address-cells' and '#size-cells' values. + +- reg-names: Should contain strings with the following names, each + representing a specific internal memory region or a + specific register space, + "l2sram", "l1pram", "l1dram", "host1cfg", "chipsig_base" + +- interrupts: Should contain the interrupt number used to receive the + interrupts from the DSP. The value should follow the + interrupt-specifier format as dictated by the + 'interrupt-parent' node. + +- memory-region: phandle to the reserved memory node to be associated + with the remoteproc device. The reserved memory node + can be a CMA memory node, and should be defined as + per the bindings in + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt + +Optional properties: +-------------------- +- interrupt-parent: phandle to the interrupt controller node. This property + is needed if the device node hierarchy doesn't have an + interrupt controller. + + +Example: +-------- + + /* DSP Reserved Memory node */ + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dsp_memory_region: dsp-memory@c3000000 { + compatible = "shared-dma-pool"; + reg = <0xc3000000 0x1000000>; + reusable; + }; + }; + + /* DSP node */ + { + dsp: dsp@11800000 { + compatible = "ti,da850-dsp"; + reg = <0x11800000 0x40000>, + <0x11e00000 0x8000>, + <0x11f00000 0x8000>, + <0x01c14044 0x4>, + <0x01c14174 0x8>; + reg-names = "l2sram", "l1pram", "l1dram", "host1cfg", + "chipsig"; + interrupt-parent = <&intc>; + interrupts = <28>; + memory-region = <&dsp_memory_region>; + }; + }; diff --git a/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt index 2aac1aa4123d..1eb72874130b 100644 --- a/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt +++ b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt @@ -26,6 +26,7 @@ The following are the mandatory properties: "ti,k2hk-dsp" for DSPs on Keystone 2 66AK2H/K SoCs "ti,k2l-dsp" for DSPs on Keystone 2 66AK2L SoCs "ti,k2e-dsp" for DSPs on Keystone 2 66AK2E SoCs + "ti,k2g-dsp" for DSPs on Keystone 2 66AK2G SoCs - reg: Should contain an entry for each value in 'reg-names'. Each entry should have the memory region's start address @@ -37,20 +38,18 @@ The following are the mandatory properties: should be defined in this order, "l2sram", "l1pram", "l1dram" -- clocks: Should contain the device's input clock, and should be - defined as per the bindings in, - Documentation/devicetree/bindings/clock/keystone-gate.txt - - ti,syscon-dev: Should be a pair of the phandle to the Keystone Device State Control node, and the register offset of the DSP boot address register within that node's address space. - resets: Should contain the phandle to the reset controller node managing the resets for this device, and a reset - specifier. Please refer to the following reset bindings - for the reset argument specifier as per SoC, + specifier. Please refer to either of the following reset + bindings for the reset argument specifier as per SoC, Documentation/devicetree/bindings/reset/ti-syscon-reset.txt - for 66AK2HK/66AK2L/66AK2E SoCs + for 66AK2HK/66AK2L/66AK2E SoCs or, + Documentation/devicetree/bindings/reset/ti,sci-reset.txt + for 66AK2G SoCs - interrupt-parent: Should contain a phandle to the Keystone 2 IRQ controller IP node that is used by the ARM CorePac processor to @@ -75,6 +74,22 @@ The following are the mandatory properties: The gpio device to be used is as per the bindings in, Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt +SoC-specific Required properties: +--------------------------------- +The following are mandatory properties for Keystone 2 66AK2HK, 66AK2L and 66AK2E +SoCs only: + +- clocks: Should contain the device's input clock, and should be + defined as per the bindings in, + Documentation/devicetree/bindings/clock/keystone-gate.txt + +The following are mandatory properties for Keystone 2 66AK2G SoCs only: + +- power-domains: Should contain a phandle to a PM domain provider node + and an args specifier containing the DSP device id + value. This property is as per the binding, + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt + Optional properties: -------------------- @@ -85,8 +100,10 @@ Optional properties: Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt -Example: --------- +Examples: +--------- + +1. /* 66AK2H/K DSP aliases */ aliases { rproc0 = &dsp0; @@ -131,3 +148,41 @@ Example: }; }; + +2. + /* 66AK2G DSP alias */ + aliases { + rproc0 = &dsp0; + }; + + /* 66AK2G DSP memory node */ + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + dsp_common_memory: dsp-common-memory@81f800000 { + compatible = "shared-dma-pool"; + reg = <0x00000008 0x1f800000 0x00000000 0x800000>; + reusable; + }; + }; + + /* 66AK2G DSP node */ + soc { + dsp0: dsp@10800000 { + compatible = "ti,k2g-dsp"; + reg = <0x10800000 0x00100000>, + <0x10e00000 0x00008000>, + <0x10f00000 0x00008000>; + reg-names = "l2sram", "l1pram", "l1dram"; + power-domains = <&k2g_pds 0x0046>; + ti,syscon-dev = <&devctrl 0x40>; + resets = <&k2g_reset 0x0046 0x1>; + interrupt-parent = <&kirq0>; + interrupts = <0 8>; + interrupt-names = "vring", "exception"; + kick-gpios = <&dspgpio0 27 0>; + memory-region = <&dsp_common_memory>; + }; + }; diff --git a/Documentation/devicetree/bindings/reset/lantiq,reset.txt b/Documentation/devicetree/bindings/reset/lantiq,reset.txt new file mode 100644 index 000000000000..c6aef36b7d15 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/lantiq,reset.txt @@ -0,0 +1,30 @@ +Lantiq XWAY SoC RCU reset controller binding +============================================ + +This binding describes a reset-controller found on the RCU module on Lantiq +XWAY SoCs. + +This node has to be a sub node of the Lantiq RCU block. + +------------------------------------------------------------------------------- +Required properties: +- compatible : Should be one of + "lantiq,danube-reset" + "lantiq,xrx200-reset" +- reg : Defines the following sets of registers in the parent + syscon device + - Offset of the reset set register + - Offset of the reset status register +- #reset-cells : Specifies the number of cells needed to encode the + reset line, should be 2. + The first cell takes the reset set bit and the + second cell takes the status bit. + +------------------------------------------------------------------------------- +Example for the reset-controllers on the xRX200 SoCs: + reset0: reset-controller@10 { + compatible = "lantiq,xrx200-reset"; + reg <0x10 0x04>, <0x14 0x04>; + + #reset-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt b/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt index b4e96a278445..05d5be48dae4 100644 --- a/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt +++ b/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt @@ -80,5 +80,4 @@ mac: ethernet@40010000 { clock-names = "stmmaceth"; resets = <&rgu 22>; reset-names = "stmmaceth"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/reset/renesas,rst.txt b/Documentation/devicetree/bindings/reset/renesas,rst.txt index fe5e0f37b3c9..e5a03ffe04fb 100644 --- a/Documentation/devicetree/bindings/reset/renesas,rst.txt +++ b/Documentation/devicetree/bindings/reset/renesas,rst.txt @@ -26,6 +26,7 @@ Required properties: - "renesas,r8a7794-rst" (R-Car E2) - "renesas,r8a7795-rst" (R-Car H3) - "renesas,r8a7796-rst" (R-Car M3-W) + - "renesas,r8a77995-rst" (R-Car D3) - reg: Address start and address range for the device. diff --git a/Documentation/devicetree/bindings/reset/uniphier-reset.txt b/Documentation/devicetree/bindings/reset/uniphier-reset.txt index 83ab0f599c40..68a6f487c409 100644 --- a/Documentation/devicetree/bindings/reset/uniphier-reset.txt +++ b/Documentation/devicetree/bindings/reset/uniphier-reset.txt @@ -6,7 +6,6 @@ System reset Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-reset" - for sLD3 SoC "socionext,uniphier-ld4-reset" - for LD4 SoC "socionext,uniphier-pro4-reset" - for Pro4 SoC "socionext,uniphier-sld8-reset" - for sLD8 SoC @@ -37,7 +36,6 @@ Media I/O (MIO) reset, SD reset Required properties: - compatible: should be one of the following: - "socionext,uniphier-sld3-mio-reset" - for sLD3 SoC "socionext,uniphier-ld4-mio-reset" - for LD4 SoC "socionext,uniphier-pro4-mio-reset" - for Pro4 SoC "socionext,uniphier-sld8-mio-reset" - for sLD8 SoC @@ -92,3 +90,28 @@ Example: other nodes ... }; + + +Analog signal amplifier reset +----------------------------- + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-ld11-adamv-reset" - for LD11 SoC + "socionext,uniphier-ld20-adamv-reset" - for LD20 SoC +- #reset-cells: should be 1. + +Example: + + adamv@57920000 { + compatible = "socionext,uniphier-ld11-adamv", + "simple-mfd", "syscon"; + reg = <0x57920000 0x1000>; + + adamv_rst: reset { + compatible = "socionext,uniphier-ld11-adamv-reset"; + #reset-cells = <1>; + }; + + other nodes ... + }; diff --git a/Documentation/devicetree/bindings/rng/imx-rngc.txt b/Documentation/devicetree/bindings/rng/imx-rngc.txt new file mode 100644 index 000000000000..93c7174a7bed --- /dev/null +++ b/Documentation/devicetree/bindings/rng/imx-rngc.txt @@ -0,0 +1,21 @@ +Freescale RNGC (Random Number Generator Version C) + +The driver also supports version B, which is mostly compatible +to version C. + +Required properties: +- compatible : should be one of + "fsl,imx25-rngb" + "fsl,imx35-rngc" +- reg : offset and length of the register set of this block +- interrupts : the interrupt number for the RNGC block +- clocks : the RNGC clk source + +Example: + +rng@53fb0000 { + compatible = "fsl,imx25-rngb"; + reg = <0x53fb0000 0x4000>; + interrupts = <22>; + clocks = <&trng_clk>; +}; diff --git a/Documentation/devicetree/bindings/rtc/google,goldfish-rtc.txt b/Documentation/devicetree/bindings/rtc/google,goldfish-rtc.txt new file mode 100644 index 000000000000..634312dd95ca --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/google,goldfish-rtc.txt @@ -0,0 +1,17 @@ +Android Goldfish RTC + +Android Goldfish RTC device used by Android emulator. + +Required properties: + +- compatible : should contain "google,goldfish-rtc" +- reg : <registers mapping> +- interrupts : <interrupt mapping> + +Example: + + goldfish_timer@9020000 { + compatible = "google,goldfish-rtc"; + reg = <0x9020000 0x1000>; + interrupts = <0x3>; + }; diff --git a/Documentation/devicetree/bindings/rtc/isil,isl12057.txt b/Documentation/devicetree/bindings/rtc/isil,isl12057.txt index cf83e0940302..fbbdd92e5af9 100644 --- a/Documentation/devicetree/bindings/rtc/isil,isl12057.txt +++ b/Documentation/devicetree/bindings/rtc/isil,isl12057.txt @@ -24,7 +24,6 @@ Optional properties: - "wakeup-source": mark the chip as a wakeup source, independently of the availability of an IRQ line connected to the SoC. - (Legacy property supported: "isil,irq2-can-wakeup-machine") - "interrupt-parent", "interrupts": for passing the interrupt line of the SoC connected to IRQ#2 of the RTC chip. diff --git a/Documentation/devicetree/bindings/rtc/realtek,rtd119x.txt b/Documentation/devicetree/bindings/rtc/realtek,rtd119x.txt new file mode 100644 index 000000000000..bbf1ccb5df31 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/realtek,rtd119x.txt @@ -0,0 +1,16 @@ +Realtek RTD129x Real-Time Clock +=============================== + +Required properties: +- compatible : Should be "realtek,rtd1295-rtc" +- reg : Specifies the physical base address and size +- clocks : Specifies the clock gate + + +Example: + + rtc@9801b600 { + compatible = "realtek,rtd1295-clk"; + reg = <0x9801b600 0x100>; + clocks = <&clkc RTD1295_CLK_EN_MISC_RTC>; + }; diff --git a/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt b/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt index 0a4c371a9b7a..a66692a08ace 100644 --- a/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt @@ -45,5 +45,4 @@ Example: interrupts = <17 1>; interrupt-names = "alarm"; st,syscfg = <&pwrcfg>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt index 945934918b71..d5e26d313f62 100644 --- a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt @@ -10,7 +10,7 @@ Required properties: Required properties for new device trees - clocks : phandle to the 32kHz external oscillator -- clock-output-names : name of the LOSC clock created +- clock-output-names : names of the LOSC and its external output clocks created - #clock-cells : must be equals to 1. The RTC provides two clocks: the LOSC and its external output, with index 0 and 1 respectively. @@ -21,7 +21,7 @@ rtc: rtc@01f00000 { compatible = "allwinner,sun6i-a31-rtc"; reg = <0x01f00000 0x54>; interrupts = <0 40 4>, <0 41 4>; - clock-output-names = "osc32k"; + clock-output-names = "osc32k", "osc32k-out"; clocks = <&ext_osc32k>; #clock-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt index 2a42a323fa1a..b6a869f97715 100644 --- a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt +++ b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt @@ -85,5 +85,4 @@ Example: <366 1>,<367 1>/* cq30-31 */ <376 4>,/* fatal ecc */ <381 4>;/* fatal axi */ - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/security/tpm/st33zp24-i2c.txt b/Documentation/devicetree/bindings/security/tpm/st33zp24-i2c.txt index 3ad115efed1e..6a4e0d30d8c4 100644 --- a/Documentation/devicetree/bindings/security/tpm/st33zp24-i2c.txt +++ b/Documentation/devicetree/bindings/security/tpm/st33zp24-i2c.txt @@ -19,7 +19,6 @@ Example (for ARM-based BeagleBoard xM with ST33ZP24 on I2C2): &i2c2 { - status = "okay"; st33zp24: st33zp24@13 { diff --git a/Documentation/devicetree/bindings/security/tpm/st33zp24-spi.txt b/Documentation/devicetree/bindings/security/tpm/st33zp24-spi.txt index 158b0165e01c..604dce901b60 100644 --- a/Documentation/devicetree/bindings/security/tpm/st33zp24-spi.txt +++ b/Documentation/devicetree/bindings/security/tpm/st33zp24-spi.txt @@ -18,7 +18,6 @@ Example (for ARM-based BeagleBoard xM with ST33ZP24 on SPI4): &mcspi4 { - status = "okay"; st33zp24@0 { diff --git a/Documentation/devicetree/bindings/security/tpm/tpm-i2c.txt b/Documentation/devicetree/bindings/security/tpm/tpm-i2c.txt index 8cb638b7e89c..a65d7b71e81a 100644 --- a/Documentation/devicetree/bindings/security/tpm/tpm-i2c.txt +++ b/Documentation/devicetree/bindings/security/tpm/tpm-i2c.txt @@ -8,6 +8,12 @@ Required properties: the firmware event log - linux,sml-size : size of the memory allocated for the firmware event log +Optional properties: + +- powered-while-suspended: present when the TPM is left powered on between + suspend and resume (makes the suspend/resume + callbacks do nothing). + Example (for OpenPower Systems with Nuvoton TPM 2.0 on I2C) ---------------------------------------------------------- @@ -17,5 +23,4 @@ tpm@57 { compatible = "nuvoton,npct650", "nuvoton,npct601"; linux,sml-base = <0x7f 0xfd450000>; linux,sml-size = <0x10000>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/security/tpm/tpm_tis_spi.txt b/Documentation/devicetree/bindings/security/tpm/tpm_tis_spi.txt index 85741cd468cc..b800667da92b 100644 --- a/Documentation/devicetree/bindings/security/tpm/tpm_tis_spi.txt +++ b/Documentation/devicetree/bindings/security/tpm/tpm_tis_spi.txt @@ -13,7 +13,6 @@ Example (for ARM-based BeagleBoard xM with TPM_TIS on SPI4): &mcspi4 { - status = "okay"; tpm_tis@0 { diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index 419ff6c0a47f..dad3b2ec66d4 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -14,6 +14,8 @@ Required properties: tegra132, or tegra210. - "nxp,lpc3220-uart" - "ralink,rt2880-uart" + - For MediaTek BTIF, must contain '"mediatek,<chip>-btif", + "mediatek,mtk-btif"' where <chip> is mt7622, mt7623. - "altr,16550-FIFO32" - "altr,16550-FIFO64" - "altr,16550-FIFO128" diff --git a/Documentation/devicetree/bindings/serial/arc-uart.txt b/Documentation/devicetree/bindings/serial/arc-uart.txt index 5cae2eb686f8..256cc150ca7e 100644 --- a/Documentation/devicetree/bindings/serial/arc-uart.txt +++ b/Documentation/devicetree/bindings/serial/arc-uart.txt @@ -15,7 +15,6 @@ arcuart0: serial@c0fc1000 { interrupts = <5>; clock-frequency = <80000000>; current-speed = <115200>; - status = "okay"; }; Note: Each port should have an alias correctly numbered in "aliases" node. diff --git a/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt b/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt index 51b3c9e80ad9..048c3818c826 100644 --- a/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt +++ b/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt @@ -15,7 +15,6 @@ serial@b00260000 { compatible = "axis,etraxfs-uart"; reg = <0xb0026000 0x1000>; interrupts = <68>; - status = "disabled"; dtr-gpios = <&sysgpio 0 GPIO_ACTIVE_LOW>; dsr-gpios = <&sysgpio 1 GPIO_ACTIVE_LOW>; rng-gpios = <&sysgpio 2 GPIO_ACTIVE_LOW>; diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt index b6cf384597e1..f73abff3de43 100644 --- a/Documentation/devicetree/bindings/serial/mtk-uart.txt +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -3,6 +3,7 @@ Required properties: - compatible should contain: * "mediatek,mt2701-uart" for MT2701 compatible UARTS + * "mediatek,mt2712-uart" for MT2712 compatible UARTS * "mediatek,mt6580-uart" for MT6580 compatible UARTS * "mediatek,mt6582-uart" for MT6582 compatible UARTS * "mediatek,mt6589-uart" for MT6589 compatible UARTS diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt index c93a2d1c1a65..d7edf732eb7f 100644 --- a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt +++ b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt @@ -33,5 +33,4 @@ serial@70006000 { reset-names = "serial"; dmas = <&apbdma 8>, <&apbdma 8>; dma-names = "rx", "tx"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt index d5f73b8f614f..9d098cf73b53 100644 --- a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt +++ b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt @@ -72,13 +72,10 @@ Examples: }; uarta: serial@12490000 { - status = "ok"; }; uartb: serial@16340000 { - status = "ok"; }; uartc: serial@1a240000 { - status = "ok"; }; diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 8d27d1a603e7..4fc96946f81d 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -41,6 +41,8 @@ Required properties: - "renesas,hscif-r8a7795" for R8A7795 (R-Car H3) HSCIF compatible UART. - "renesas,scif-r8a7796" for R8A7796 (R-Car M3-W) SCIF compatible UART. - "renesas,hscif-r8a7796" for R8A7796 (R-Car M3-W) HSCIF compatible UART. + - "renesas,scif-r8a77995" for R8A77995 (R-Car D3) SCIF compatible UART. + - "renesas,hscif-r8a77995" for R8A77995 (R-Car D3) HSCIF compatible UART. - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. - "renesas,rcar-gen1-scif" for R-Car Gen1 SCIF compatible UART, diff --git a/Documentation/devicetree/bindings/serial/rs485.txt b/Documentation/devicetree/bindings/serial/rs485.txt index 32b1fa1f2a5b..b8415936dfdb 100644 --- a/Documentation/devicetree/bindings/serial/rs485.txt +++ b/Documentation/devicetree/bindings/serial/rs485.txt @@ -5,14 +5,13 @@ the built-in half-duplex mode. The properties described hereafter shall be given to a half-duplex capable UART node. -Required properties: +Optional properties: - rs485-rts-delay: prop-encoded-array <a b> where: * a is the delay between rts signal and beginning of data sent in milliseconds. it corresponds to the delay before sending data. * b is the delay between end of data sent and rts signal in milliseconds it corresponds to the delay after sending data and actual release of the line. - -Optional properties: + If this property is not specified, <0 0> is assumed. - linux,rs485-enabled-at-boot-time: empty property telling to enable the rs485 feature at boot time. It can be disabled later with proper ioctl. - rs485-rx-during-tx: empty property that enables the receiving of data even diff --git a/Documentation/devicetree/bindings/serial/serial.txt b/Documentation/devicetree/bindings/serial/serial.txt index b542a0ecf06e..863c2893759e 100644 --- a/Documentation/devicetree/bindings/serial/serial.txt +++ b/Documentation/devicetree/bindings/serial/serial.txt @@ -43,7 +43,6 @@ Examples: rng-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>; cts-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; rts-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; - status = "okay"; }; scifa4: serial@e6c80000 { @@ -54,5 +53,4 @@ Examples: clock-names = "fck"; power-domains = <&pd_a3sp>; uart-has-rtscts; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/serial/st,stm32-usart.txt b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt index 85ec5f2b1996..3657f9f9d17a 100644 --- a/Documentation/devicetree/bindings/serial/st,stm32-usart.txt +++ b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt @@ -1,12 +1,19 @@ * STMicroelectronics STM32 USART Required properties: -- compatible: Can be either "st,stm32-usart", "st,stm32-uart", -"st,stm32f7-usart" or "st,stm32f7-uart" depending on whether -the device supports synchronous mode and is compatible with -stm32(f4) or stm32f7. +- compatible: can be either: + - "st,stm32-usart", + - "st,stm32-uart", + - "st,stm32f7-usart", + - "st,stm32f7-uart", + - "st,stm32h7-usart" + - "st,stm32h7-uart". + depending on whether the device supports synchronous mode + and is compatible with stm32(f4), stm32f7 or stm32h7. - reg: The address and length of the peripheral registers space -- interrupts: The interrupt line of the USART instance +- interrupts: + - The interrupt line for the USART instance, + - An optional wake-up interrupt. - clocks: The input clock of the USART instance Optional properties: diff --git a/Documentation/devicetree/bindings/serio/allwinner,sun4i-ps2.txt b/Documentation/devicetree/bindings/serio/allwinner,sun4i-ps2.txt index 362a76925bcd..f311472990a7 100644 --- a/Documentation/devicetree/bindings/serio/allwinner,sun4i-ps2.txt +++ b/Documentation/devicetree/bindings/serio/allwinner,sun4i-ps2.txt @@ -19,5 +19,4 @@ Example: reg = <0x01c2a000 0x400>; interrupts = <0 62 4>; clocks = <&apb1_gates 6>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/serio/ps2-gpio.txt b/Documentation/devicetree/bindings/serio/ps2-gpio.txt new file mode 100644 index 000000000000..7b7bc9cdf986 --- /dev/null +++ b/Documentation/devicetree/bindings/serio/ps2-gpio.txt @@ -0,0 +1,23 @@ +Device-Tree binding for ps/2 gpio device + +Required properties: + - compatible = "ps2-gpio" + - data-gpios: the data pin + - clk-gpios: the clock pin + - interrupts: Should trigger on the falling edge of the clock line. + +Optional properties: + - write-enable: Indicates whether write function is provided + to serio device. Possibly providing the write fn will not work, because + of the tough timing requirements. + +Example nodes: + +ps2@0 { + compatible = "ps2-gpio"; + interrupt-parent = <&gpio>; + interrupts = <23 IRQ_TYPE_EDGE_FALLING>; + data-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>; + clk-gpios = <&gpio 23 GPIO_ACTIVE_HIGH>; + write-enable; +}; diff --git a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt index b1d165b4d4b3..40056f7990f8 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt @@ -12,11 +12,13 @@ power/power_domain.txt. It provides the power domains defined in - include/dt-bindings/power/mt8173-power.h - include/dt-bindings/power/mt6797-power.h - include/dt-bindings/power/mt2701-power.h +- include/dt-bindings/power/mt7622-power.h Required properties: - compatible: Should be one of: - "mediatek,mt2701-scpsys" - "mediatek,mt6797-scpsys" + - "mediatek,mt7622-scpsys" - "mediatek,mt8173-scpsys" - #power-domain-cells: Must be 1 - reg: Address range of the SCPSYS unit @@ -26,6 +28,7 @@ Required properties: enabled before enabling certain power domains. Required clocks for MT2701: "mm", "mfg", "ethif" Required clocks for MT6797: "mm", "mfg", "vdec" + Required clocks for MT7622: "hif_sel" Required clocks for MT8173: "mm", "mfg", "venc", "venc_lt" Optional properties: diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt index 50fc20c6ce91..b277eca861f7 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,glink.txt @@ -1,11 +1,12 @@ -Qualcomm RPM GLINK binding +Qualcomm GLINK edge binding -This binding describes the Qualcomm RPM GLINK, a fifo based mechanism for -communication with the Resource Power Management system on various Qualcomm -platforms. +This binding describes a Qualcomm GLINK edge, a fifo based mechanism for +communication between subsystem-pairs on various Qualcomm platforms. Two types +of edges can be described by the binding; the GLINK RPM edge and a SMEM based +edge. - compatible: - Usage: required + Usage: required for glink-rpm Value type: <stringlist> Definition: must be "qcom,glink-rpm" @@ -16,7 +17,7 @@ platforms. signal this processor about communication related events - qcom,rpm-msg-ram: - Usage: required + Usage: required for glink-rpm Value type: <prop-encoded-array> Definition: handle to RPM message memory resource diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt index 2f5ede39bea2..fe1855f09dcc 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt @@ -78,7 +78,6 @@ Example for APQ8064: interrupts = <0 152 0x0>; clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>; clock-names = "core", "iface"; - status = "ok"; }; }; diff --git a/Documentation/devicetree/bindings/soc/rockchip/grf.txt b/Documentation/devicetree/bindings/soc/rockchip/grf.txt index cc9f05d3cbc1..7dc5ce858a0e 100644 --- a/Documentation/devicetree/bindings/soc/rockchip/grf.txt +++ b/Documentation/devicetree/bindings/soc/rockchip/grf.txt @@ -21,6 +21,7 @@ Required Properties: - "rockchip,rk3328-grf", "syscon": for rk3328 - "rockchip,rk3368-grf", "syscon": for rk3368 - "rockchip,rk3399-grf", "syscon": for rk3399 + - "rockchip,rv1108-grf", "syscon": for rv1108 - compatible: PMUGRF should be one of the following: - "rockchip,rk3368-pmugrf", "syscon": for rk3368 - "rockchip,rk3399-pmugrf", "syscon": for rk3399 @@ -28,6 +29,8 @@ Required Properties: - "rockchip,rk3288-sgrf", "syscon": for rk3288 - compatible: USB2PHYGRF should be one of the followings - "rockchip,rk3328-usb2phy-grf", "syscon": for rk3328 +- compatible: USBGRF should be one of the following + - "rockchip,rv1108-usbgrf", "syscon": for rv1108 - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt index 01bfb6745fbd..301d2a9bc1b8 100644 --- a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +++ b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt @@ -7,6 +7,7 @@ Required properties for power domain controller: - compatible: Should be one of the following. "rockchip,rk3288-power-controller" - for RK3288 SoCs. "rockchip,rk3328-power-controller" - for RK3328 SoCs. + "rockchip,rk3366-power-controller" - for RK3366 SoCs. "rockchip,rk3368-power-controller" - for RK3368 SoCs. "rockchip,rk3399-power-controller" - for RK3399 SoCs. - #power-domain-cells: Number of cells in a power-domain specifier. @@ -18,6 +19,7 @@ Required properties for power domain sub nodes: - reg: index of the power domain, should use macros in: "include/dt-bindings/power/rk3288-power.h" - for RK3288 type power domain. "include/dt-bindings/power/rk3328-power.h" - for RK3328 type power domain. + "include/dt-bindings/power/rk3366-power.h" - for RK3366 type power domain. "include/dt-bindings/power/rk3368-power.h" - for RK3368 type power domain. "include/dt-bindings/power/rk3399-power.h" - for RK3399 type power domain. - clocks (optional): phandles to clocks which need to be enabled while power domain @@ -93,6 +95,7 @@ power domain to use. The index should use macros in: "include/dt-bindings/power/rk3288-power.h" - for rk3288 type power domain. "include/dt-bindings/power/rk3328-power.h" - for rk3328 type power domain. + "include/dt-bindings/power/rk3366-power.h" - for rk3366 type power domain. "include/dt-bindings/power/rk3368-power.h" - for rk3368 type power domain. "include/dt-bindings/power/rk3399-power.h" - for rk3399 type power domain. diff --git a/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt b/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt index c705db07d820..66e6265fb0aa 100644 --- a/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt +++ b/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt @@ -46,12 +46,13 @@ Required Properties: - power-domains: phandle pointing to the corresponding PM domain node and an ID representing the device. -See dt-bindings/genpd/k2g.h for the list of valid identifiers for k2g. +See http://processors.wiki.ti.com/index.php/TISCI#66AK2G02_Data for the list +of valid identifiers for k2g. Example (K2G): -------------------- uart0: serial@02530c00 { compatible = "ns16550a"; ... - power-domains = <&k2g_pds K2G_DEV_UART0>; + power-domains = <&k2g_pds 0x002c>; }; diff --git a/Documentation/devicetree/bindings/sound/armada-370db-audio.txt b/Documentation/devicetree/bindings/sound/armada-370db-audio.txt index bf984d238620..953c092db72f 100644 --- a/Documentation/devicetree/bindings/sound/armada-370db-audio.txt +++ b/Documentation/devicetree/bindings/sound/armada-370db-audio.txt @@ -23,5 +23,4 @@ Example: compatible = "marvell,a370db-audio"; marvell,audio-controller = <&audio_controller>; marvell,audio-codec = <&audio_codec &spdif_out &spdif_in>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/sound/atmel-classd.txt b/Documentation/devicetree/bindings/sound/atmel-classd.txt index 549e701cb7a1..898551076382 100644 --- a/Documentation/devicetree/bindings/sound/atmel-classd.txt +++ b/Documentation/devicetree/bindings/sound/atmel-classd.txt @@ -13,13 +13,11 @@ Required properties: Must be "tx". - clock-names Tuple listing input clock names. - Required elements: "pclk", "gclk" and "aclk". + Required elements: "pclk" and "gclk". - clocks Please refer to clock-bindings.txt. - assigned-clocks Should be <&classd_gclk>. -- assigned-clock-parents - Should be <&audio_pll_pmc>. Optional properties: - pinctrl-names, pinctrl-0 @@ -45,10 +43,9 @@ classd: classd@fc048000 { (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(47))>; dma-names = "tx"; - clocks = <&classd_clk>, <&classd_gclk>, <&audio_pll_pmc>; - clock-names = "pclk", "gclk", "aclk"; + clocks = <&classd_clk>, <&classd_gclk>; + clock-names = "pclk", "gclk"; assigned-clocks = <&classd_gclk>; - assigned-clock-parents = <&audio_pll_pmc>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_classd_default>; diff --git a/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt b/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt index fdb25b492514..9d049d4bfd58 100644 --- a/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt +++ b/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt @@ -45,7 +45,6 @@ Example: &ssc0 { #sound-dai-cells = <0>; - status = "okay"; }; &i2c { diff --git a/Documentation/devicetree/bindings/sound/brcm,cygnus-audio.txt b/Documentation/devicetree/bindings/sound/brcm,cygnus-audio.txt index b139e66d2a11..630bf7c0344d 100644 --- a/Documentation/devicetree/bindings/sound/brcm,cygnus-audio.txt +++ b/Documentation/devicetree/bindings/sound/brcm,cygnus-audio.txt @@ -47,21 +47,17 @@ Example: ssp0: ssp_port@0 { reg = <0>; - status = "okay"; }; ssp1: ssp_port@1 { reg = <1>; - status = "disabled"; }; ssp2: ssp_port@2 { reg = <2>; - status = "disabled"; }; spdif: spdif_port@3 { reg = <3>; - status = "disabled"; }; }; diff --git a/Documentation/devicetree/bindings/sound/cs43130.txt b/Documentation/devicetree/bindings/sound/cs43130.txt new file mode 100644 index 000000000000..8b1dd5aeb004 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs43130.txt @@ -0,0 +1,67 @@ +CS43130 DAC + +Required properties: + + - compatible : "cirrus,cs43130", "cirrus,cs4399", "cirrus,cs43131", + "cirrus,cs43198" + + - reg : the I2C address of the device for I2C + + - VA-supply, VP-supply, VL-supply, VCP-supply, VD-supply: + power supplies for the device, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + + +Optional properties: + + - reset-gpios : Active low GPIO used to reset the device + + - cirrus,xtal-ibias: + When external MCLK is generated by external crystal + oscillator, CS43130 can be used to provide bias current + for external crystal. Amount of bias current sent is + set as: + 1 = 7.5uA + 2 = 12.5uA + 3 = 15uA + + - cirrus,dc-measure: + Boolean, define to enable headphone DC impedance measurement. + + - cirrus,ac-measure: + Boolean, define to enable headphone AC impedance measurement. + DC impedance must also be enabled for AC impedance measurement. + + - cirrus,dc-threshold: + Define 2 DC impedance thresholds in ohms for HP output control. + Default values are 50 and 120 Ohms. + + - cirrus,ac-freq: + Define the frequencies at which to measure HP AC impedance. + Only used if "cirrus,dc-measure" is defined. + Exactly 10 frequencies must be defined. + If this properties is undefined, by default, + following frequencies are used: + <24 43 93 200 431 928 2000 4309 9283 20000> + The above frequencies are logarithmically equally spaced. + Log base is 10. + +Example: + +cs43130: audio-codec@30 { + compatible = "cirrus,cs43130"; + reg = <0x30>; + reset-gpios = <&axi_gpio 54 0>; + VA-supply = <&dummy_vreg>; + VP-supply = <&dummy_vreg>; + VL-supply = <&dummy_vreg>; + VCP-supply = <&dummy_vreg>; + VD-supply = <&dummy_vreg>; + cirrus,xtal-ibias = <2>; + interrupt-parent = <&gpio0>; + interrupts = <55 8>; + cirrus,dc-measure; + cirrus,ac-measure; + cirrus,dc-threshold = /bits/ 16 <20 100>; + cirrus,ac-freq = /bits/ 16 <24 43 93 200 431 928 2000 4309 9283 20000>; +}; diff --git a/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt index e0b6165c9cfc..3ffc2562fb31 100644 --- a/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt +++ b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt @@ -47,5 +47,4 @@ mcbsp0: mcbsp@1d10000 { dmas = <&edma0 3 1 &edma0 2 1>; dma-names = "tx", "rx"; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/sound/dmic.txt b/Documentation/devicetree/bindings/sound/dmic.txt new file mode 100644 index 000000000000..54c8ef6498a8 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/dmic.txt @@ -0,0 +1,16 @@ +Device-Tree bindings for Digital microphone (DMIC) codec + +This device support generic PDM digital microphone. + +Required properties: + - compatible: should be "dmic-codec". + +Optional properties: + - dmicen-gpios: GPIO specifier for dmic to control start and stop + +Example node: + + dmic_codec: dmic@0 { + compatible = "dmic-codec"; + dmicen-gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/sound/fsl,asrc.txt b/Documentation/devicetree/bindings/sound/fsl,asrc.txt index 3e26a9478e57..65979b205893 100644 --- a/Documentation/devicetree/bindings/sound/fsl,asrc.txt +++ b/Documentation/devicetree/bindings/sound/fsl,asrc.txt @@ -61,5 +61,4 @@ asrc: asrc@02034000 { "txa", "txb", "txc"; fsl,asrc-rate = <48000>; fsl,asrc-width = <16>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/sound/fsl,esai.txt b/Documentation/devicetree/bindings/sound/fsl,esai.txt index cd3ee5d84f03..21c401e2ccda 100644 --- a/Documentation/devicetree/bindings/sound/fsl,esai.txt +++ b/Documentation/devicetree/bindings/sound/fsl,esai.txt @@ -59,5 +59,4 @@ esai: esai@02024000 { fsl,fifo-depth = <128>; fsl,esai-synchronous; big-endian; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/sound/fsl,spdif.txt b/Documentation/devicetree/bindings/sound/fsl,spdif.txt index 4ca39ddc0417..0f97e54c3d43 100644 --- a/Documentation/devicetree/bindings/sound/fsl,spdif.txt +++ b/Documentation/devicetree/bindings/sound/fsl,spdif.txt @@ -59,5 +59,4 @@ spdif: spdif@02004000 { "rxtx7"; big-endian; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/sound/hdmi.txt b/Documentation/devicetree/bindings/sound/hdmi.txt index 31af7bca3099..56407c30e954 100644 --- a/Documentation/devicetree/bindings/sound/hdmi.txt +++ b/Documentation/devicetree/bindings/sound/hdmi.txt @@ -13,5 +13,4 @@ Example node: hdmi_audio: hdmi_audio@0 { compatible = "linux,hdmi-audio"; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt b/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt index 9800a560e0c2..77a57f84bed4 100644 --- a/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt +++ b/Documentation/devicetree/bindings/sound/mt2701-afe-pcm.txt @@ -3,7 +3,8 @@ Mediatek AFE PCM controller for mt2701 Required properties: - compatible = "mediatek,mt2701-audio"; - reg: register location and size -- interrupts: Should contain AFE interrupt +- interrupts: should contain AFE and ASYS interrupts +- interrupt-names: should be "afe" and "asys" - power-domains: should define the power domain - clock-names: should have these clock names: "infra_sys_audio_clk", @@ -59,6 +60,7 @@ Example: <0 0x112A0000 0 0x20000>; interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>, <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "afe", "asys"; power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>; clocks = <&infracfg CLK_INFRA_AUDIO>, <&topckgen CLK_TOP_AUD_MUX1_SEL>, diff --git a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt index ccb401cfef9d..551ecab67efe 100644 --- a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt +++ b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt @@ -31,8 +31,22 @@ Required properties - vdd-cdc-io-supply: phandle to VDD_CDC_IO regulator DT node. - vdd-cdc-tx-rx-cx-supply: phandle to VDD_CDC_TX/RX/CX regulator DT node. - vdd-micbias-supply: phandle of VDD_MICBIAS supply's regulator DT node. - Optional Properties: + - qcom,mbhc-vthreshold-low: Array of 5 threshold voltages in mV for 5 buttons + detection on headset when the mbhc is powered up + by internal current source, this is a low power. + - qcom,mbhc-vthreshold-high: Array of 5 thresold voltages in mV for 5 buttons + detection on headset when mbhc is powered up + from micbias. +- qcom,micbias-lvl: Voltage (mV) for Mic Bias +- qcom,hphl-jack-type-normally-open: boolean, present if hphl pin on jack is a + NO (Normally Open). If not specified, then + its assumed that hphl pin on jack is NC + (Normally Closed). +- qcom,gnd-jack-type-normally-open: boolean, present if gnd pin on jack is + NO (Normally Open). If not specified, then + its assumed that gnd pin on jack is NC + (Normally Closed). - qcom,micbias1-ext-cap: boolean, present if micbias1 has external capacitor connected. - qcom,micbias2-ext-cap: boolean, present if micbias2 has external capacitor @@ -48,6 +62,8 @@ spmi_bus { reg-names = "pmic-codec-core"; clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>; clock-names = "mclk"; + qcom,mbhc-vthreshold-low = <75 150 237 450 500>; + qcom,mbhc-vthreshold-high = <75 150 237 450 500>; interrupt-parent = <&spmi_bus>; interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>, <0x1 0xf0 0x1 IRQ_TYPE_NONE>, diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index 7246bb268bf9..085bec364caf 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -199,10 +199,10 @@ Ex) sound { compatible = "simple-scu-audio-card"; ... - simple-audio-card,cpu@0 { + simple-audio-card,cpu-0 { sound-dai = <&rcar_sound 0>; }; - simple-audio-card,cpu@1 { + simple-audio-card,cpu-1 { sound-dai = <&rcar_sound 1>; }; simple-audio-card,codec { @@ -441,79 +441,79 @@ rcar_sound: sound@ec500000 { "clk_a", "clk_b", "clk_c", "clk_i"; rcar_sound,dvc { - dvc0: dvc@0 { + dvc0: dvc-0 { dmas = <&audma0 0xbc>; dma-names = "tx"; }; - dvc1: dvc@1 { + dvc1: dvc-1 { dmas = <&audma0 0xbe>; dma-names = "tx"; }; }; rcar_sound,mix { - mix0: mix@0 { }; - mix1: mix@1 { }; + mix0: mix-0 { }; + mix1: mix-1 { }; }; rcar_sound,ctu { - ctu00: ctu@0 { }; - ctu01: ctu@1 { }; - ctu02: ctu@2 { }; - ctu03: ctu@3 { }; - ctu10: ctu@4 { }; - ctu11: ctu@5 { }; - ctu12: ctu@6 { }; - ctu13: ctu@7 { }; + ctu00: ctu-0 { }; + ctu01: ctu-1 { }; + ctu02: ctu-2 { }; + ctu03: ctu-3 { }; + ctu10: ctu-4 { }; + ctu11: ctu-5 { }; + ctu12: ctu-6 { }; + ctu13: ctu-7 { }; }; rcar_sound,src { - src0: src@0 { + src0: src-0 { interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x85>, <&audma1 0x9a>; dma-names = "rx", "tx"; }; - src1: src@1 { + src1: src-1 { interrupts = <0 353 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x87>, <&audma1 0x9c>; dma-names = "rx", "tx"; }; - src2: src@2 { + src2: src-2 { interrupts = <0 354 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x89>, <&audma1 0x9e>; dma-names = "rx", "tx"; }; - src3: src@3 { + src3: src-3 { interrupts = <0 355 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x8b>, <&audma1 0xa0>; dma-names = "rx", "tx"; }; - src4: src@4 { + src4: src-4 { interrupts = <0 356 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x8d>, <&audma1 0xb0>; dma-names = "rx", "tx"; }; - src5: src@5 { + src5: src-5 { interrupts = <0 357 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x8f>, <&audma1 0xb2>; dma-names = "rx", "tx"; }; - src6: src@6 { + src6: src-6 { interrupts = <0 358 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x91>, <&audma1 0xb4>; dma-names = "rx", "tx"; }; - src7: src@7 { + src7: src-7 { interrupts = <0 359 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x93>, <&audma1 0xb6>; dma-names = "rx", "tx"; }; - src8: src@8 { + src8: src-8 { interrupts = <0 360 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x95>, <&audma1 0xb8>; dma-names = "rx", "tx"; }; - src9: src@9 { + src9: src-9 { interrupts = <0 361 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x97>, <&audma1 0xba>; dma-names = "rx", "tx"; @@ -521,52 +521,52 @@ rcar_sound: sound@ec500000 { }; rcar_sound,ssi { - ssi0: ssi@0 { + ssi0: ssi-0 { interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi1: ssi@1 { + ssi1: ssi-1 { interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi2: ssi@2 { + ssi2: ssi-2 { interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi3: ssi@3 { + ssi3: ssi-3 { interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi4: ssi@4 { + ssi4: ssi-4 { interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi5: ssi@5 { + ssi5: ssi-5 { interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi6: ssi@6 { + ssi6: ssi-6 { interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi7: ssi@7 { + ssi7: ssi-7 { interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi8: ssi@8 { + ssi8: ssi-8 { interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi9: ssi@9 { + ssi9: ssi-9 { interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>; dma-names = "rx", "tx", "rxu", "txu"; @@ -621,7 +621,6 @@ Example: simple sound card /* Single DAI */ #sound-dai-cells = <0>; - status = "okay"; rcar_sound,dai { dai0 { @@ -667,7 +666,6 @@ Example: simple sound card for Multi channel /* Single DAI */ #sound-dai-cells = <0>; - status = "okay"; rcar_sound,dai { dai0 { diff --git a/Documentation/devicetree/bindings/sound/rockchip,pdm.txt b/Documentation/devicetree/bindings/sound/rockchip,pdm.txt index 921729de7346..47f164fbd1d7 100644 --- a/Documentation/devicetree/bindings/sound/rockchip,pdm.txt +++ b/Documentation/devicetree/bindings/sound/rockchip,pdm.txt @@ -29,11 +29,13 @@ pdm: pdm@ff040000 { dma-names = "rx"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&pdmm0_clk - &pdmm0_fsync &pdmm0_sdi0 &pdmm0_sdi1 &pdmm0_sdi2 &pdmm0_sdi3>; - pinctrl-1 = <&pdmm0_sleep>; - status = "disabled"; + pinctrl-1 = <&pdmm0_clk_sleep + &pdmm0_sdi0_sleep + &pdmm0_sdi1_sleep + &pdmm0_sdi2_sleep + &pdmm0_sdi3_sleep>; }; diff --git a/Documentation/devicetree/bindings/sound/rockchip,rk3399-gru-sound.txt b/Documentation/devicetree/bindings/sound/rockchip,rk3399-gru-sound.txt index eac91db07178..72d3cf4c2606 100644 --- a/Documentation/devicetree/bindings/sound/rockchip,rk3399-gru-sound.txt +++ b/Documentation/devicetree/bindings/sound/rockchip,rk3399-gru-sound.txt @@ -4,7 +4,7 @@ Required properties: - compatible: "rockchip,rk3399-gru-sound" - rockchip,cpu: The phandle of the Rockchip I2S controller that's connected to the codecs -- rockchip,codec: The phandle of the MAX98357A/RT5514/DA7219 codecs +- rockchip,codec: The phandle of the audio codecs Optional properties: - dmic-wakeup-delay-ms : specify delay time (ms) for DMIC ready. diff --git a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt index 206aba1b34bb..b208a752576c 100644 --- a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt +++ b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt @@ -7,8 +7,12 @@ Required properties: - compatible: should be one of the following: - "rockchip,rk3066-i2s": for rk3066 + - "rockchip,rk3036-i2s", "rockchip,rk3066-i2s": for rk3036 - "rockchip,rk3188-i2s", "rockchip,rk3066-i2s": for rk3188 + - "rockchip,rk3228-i2s", "rockchip,rk3066-i2s": for rk3228 - "rockchip,rk3288-i2s", "rockchip,rk3066-i2s": for rk3288 + - "rockchip,rk3328-i2s", "rockchip,rk3066-i2s": for rk3328 + - "rockchip,rk3366-i2s", "rockchip,rk3066-i2s": for rk3366 - "rockchip,rk3368-i2s", "rockchip,rk3066-i2s": for rk3368 - "rockchip,rk3399-i2s", "rockchip,rk3066-i2s": for rk3399 - reg: physical base address of the controller and length of memory mapped diff --git a/Documentation/devicetree/bindings/sound/rockchip-spdif.txt b/Documentation/devicetree/bindings/sound/rockchip-spdif.txt index 4706b96d450b..0a1dc4e1815c 100644 --- a/Documentation/devicetree/bindings/sound/rockchip-spdif.txt +++ b/Documentation/devicetree/bindings/sound/rockchip-spdif.txt @@ -41,6 +41,5 @@ spdif: spdif@0x1011e000 { dma-names = "tx"; clock-names = "hclk", "mclk"; clocks = <&cru HCLK_SPDIF>, <&cru SCLK_SPDIF>; - status = "disabled"; #sound-dai-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/sound/rt274.txt b/Documentation/devicetree/bindings/sound/rt274.txt new file mode 100644 index 000000000000..e9a6178c78cf --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt274.txt @@ -0,0 +1,33 @@ +RT274 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt274". + +- reg : The I2C address of the device. + +Optional properties: + +- interrupts : The CODEC's interrupt output. + + +Pins on the device (for linking into audio routes) for RT274: + + * DMIC1 Pin + * DMIC2 Pin + * MIC + * LINE1 + * LINE2 + * HPO Pin + * SPDIF + * LINE3 + +Example: + +codec: rt274@1c { + compatible = "realtek,rt274"; + reg = <0x1c>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5663.txt b/Documentation/devicetree/bindings/sound/rt5663.txt index 70eaeaed2b18..ff381718c517 100644 --- a/Documentation/devicetree/bindings/sound/rt5663.txt +++ b/Documentation/devicetree/bindings/sound/rt5663.txt @@ -12,6 +12,14 @@ Required properties: Optional properties: +- "realtek,dc_offset_l_manual" +- "realtek,dc_offset_r_manual" +- "realtek,dc_offset_l_manual_mic" +- "realtek,dc_offset_r_manual_mic" + Based on the different PCB layout, add the manual offset value to + compensate the DC offset for each L and R channel, and they are different + between headphone and headset. + Pins on the device (for linking into audio routes) for RT5663: * IN1P diff --git a/Documentation/devicetree/bindings/sound/samsung,odroid.txt b/Documentation/devicetree/bindings/sound/samsung,odroid.txt index c30934dd975b..625b1b18fd02 100644 --- a/Documentation/devicetree/bindings/sound/samsung,odroid.txt +++ b/Documentation/devicetree/bindings/sound/samsung,odroid.txt @@ -7,9 +7,6 @@ Required properties: - model - the user-visible name of this sound complex - clocks - should contain entries matching clock names in the clock-names property - - clock-names - should contain following entries: - - "epll" - indicating the EPLL output clock - - "i2s_rclk" - indicating the RCLK (root) clock of the I2S0 controller - samsung,audio-widgets - this property specifies off-codec audio elements like headphones or speakers, for details see widgets.txt - samsung,audio-routing - a list of the connections between audio @@ -46,9 +43,6 @@ sound { "IN1", "Mic Jack", "Mic Jack", "MICBIAS"; - clocks = <&clock CLK_FOUT_EPLL>, <&i2s0 CLK_I2S_RCLK_SRC>; - clock-names = "epll", "sclk_i2s"; - cpu { sound-dai = <&i2s0 0>; }; diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt index c7a93931fad2..166f2290233b 100644 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-card.txt @@ -86,6 +86,9 @@ Optional CPU/CODEC subnodes properties: in dai startup() and disabled with clk_disable_unprepare() in dai shutdown(). +- system-clock-direction-out : specifies clock direction as 'out' on + initialization. It is useful for some aCPUs with + fixed clocks. Example 1 - single DAI link: diff --git a/Documentation/devicetree/bindings/sound/simple-scu-card.txt b/Documentation/devicetree/bindings/sound/simple-scu-card.txt index 327d229a51b2..32f8dbce5241 100644 --- a/Documentation/devicetree/bindings/sound/simple-scu-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-scu-card.txt @@ -24,6 +24,7 @@ Optional subnode properties: - simple-audio-card,convert-rate : platform specified sampling rate convert - simple-audio-card,convert-channels : platform specified converted channel size (2 - 8 ch) - simple-audio-card,prefix : see routing +- simple-audio-card,widgets : Please refer to widgets.txt. - simple-audio-card,routing : A list of the connections between audio components. Each entry is a pair of strings, the first being the connection's sink, the second being the connection's source. Valid names for sources. diff --git a/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt index 745dc62f76ea..40068ec0e9a5 100644 --- a/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt +++ b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt @@ -53,7 +53,6 @@ Example: sti_uni_player1: sti-uni-player@0x8D81000 { compatible = "st,stih407-uni-player-hdmi"; - status = "okay"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; clocks = <&clk_s_d0_flexgen CLK_PCM_1>; @@ -66,7 +65,6 @@ Example: sti_uni_player2: sti-uni-player@0x8D82000 { compatible = "st,stih407-uni-player-pcm-out"; - status = "okay"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; clocks = <&clk_s_d0_flexgen CLK_PCM_2>; @@ -78,7 +76,6 @@ Example: sti_uni_player3: sti-uni-player@0x8D85000 { compatible = "st,stih407-uni-player-spdif"; - status = "okay"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; clocks = <&clk_s_d0_flexgen CLK_SPDIFF>; @@ -90,7 +87,6 @@ Example: sti_uni_reader1: sti-uni-reader@0x8D84000 { compatible = "st,stih407-uni-reader-hdmi"; - status = "disabled"; #sound-dai-cells = <0>; st,syscfg = <&syscfg_core>; reg = <0x8D84000 0x158>; @@ -125,7 +121,6 @@ Example of audio card declaration: sound { compatible = "simple-audio-card"; simple-audio-card,name = "sti audio card"; - status = "okay"; simple-audio-card,dai-link@0 { /* DAC */ diff --git a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt index ee21da865771..fc5da6080759 100644 --- a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt +++ b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt @@ -8,6 +8,7 @@ Required properties: - compatible: should be one of the following: - "allwinner,sun4i-a10-i2s" - "allwinner,sun6i-a31-i2s" + - "allwinner,sun8i-h3-i2s" - reg: physical base address of the controller and length of memory mapped region. - interrupts: should contain the I2S interrupt. @@ -22,6 +23,7 @@ Required properties: Required properties for the following compatibles: - "allwinner,sun6i-a31-i2s" + - "allwinner,sun8i-h3-i2s" - resets: phandle to the reset line for this codec Example: diff --git a/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt b/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt index fe0a65e6d629..70ee177901d3 100644 --- a/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt +++ b/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt @@ -39,5 +39,4 @@ spdif: spdif@01c21000 { clock-names = "apb", "spdif"; dmas = <&dma 0 2>, <&dma 0 2>; dma-names = "rx", "tx"; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/sound/tas5720.txt b/Documentation/devicetree/bindings/sound/tas5720.txt index 806ea7381483..40d94f82beb3 100644 --- a/Documentation/devicetree/bindings/sound/tas5720.txt +++ b/Documentation/devicetree/bindings/sound/tas5720.txt @@ -17,7 +17,6 @@ Required properties: Example: tas5720: tas5720@6c { - status = "okay"; compatible = "ti,tas5720"; reg = <0x6c>; dvdd-supply = <&vdd_3v3_reg>; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt b/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt index 5e2741af27be..ca75890f0d07 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt @@ -3,7 +3,9 @@ Texas Instruments - tlv320aic32x4 Codec module The tlv320aic32x4 serial control bus communicates through I2C protocols Required properties: - - compatible: Should be "ti,tlv320aic32x4" + - compatible - "string" - One of: + "ti,tlv320aic32x4" TLV320AIC3204 + "ti,tlv320aic32x6" TLV320AIC3206, TLV320AIC3256 - reg: I2C slave address - supply-*: Required supply regulators are: "iov" - digital IO power supply @@ -18,6 +20,8 @@ Optional properties: - reset-gpios: Reset-GPIO phandle with args as described in gpio/gpio.txt - clocks/clock-names: Clock named 'mclk' for the master clock of the codec. See clock/clock-bindings.txt for information about the detailed format. + - aic32x4-gpio-func - <array of 5 int> + - Types are defined in include/sound/tlv320aic32x4.h Example: @@ -27,4 +31,11 @@ codec: tlv320aic32x4@18 { reg = <0x18>; clocks = <&clks 201>; clock-names = "mclk"; + aic32x4-gpio-func= < + 0xff /* AIC32X4_MFPX_DEFAULT_VALUE */ + 0xff /* AIC32X4_MFPX_DEFAULT_VALUE */ + 0x04 /* MFP3 AIC32X4_MFP3_GPIO_ENABLED */ + 0xff /* AIC32X4_MFPX_DEFAULT_VALUE */ + 0x08 /* MFP5 AIC32X4_MFP5_GPIO_INPUT */ + >; }; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt index 47a213c411ce..ba5b45c483f5 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt @@ -26,6 +26,11 @@ Optional properties: 3 - MICBIAS output is connected to AVDD, If this node is not mentioned or if the value is incorrect, then MicBias is powered down. +- ai3x-ocmv - Output Common-Mode Voltage selection: + 0 - 1.35V, + 1 - 1.5V, + 2 - 1.65V, + 3 - 1.8V - AVDD-supply, IOVDD-supply, DRVDD-supply, DVDD-supply : power supplies for the device as covered in Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/sound/wm8524.txt b/Documentation/devicetree/bindings/sound/wm8524.txt new file mode 100644 index 000000000000..20c62002cbcd --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8524.txt @@ -0,0 +1,16 @@ +WM8524 audio CODEC + +This device does not use I2C or SPI but a simple Hardware Control Interface. + +Required properties: + + - compatible : "wlf,wm8524" + + - wlf,mute-gpios: a GPIO spec for the MUTE pin. + +Example: + +codec: wm8524@0 { + compatible = "wlf,wm8524"; + wlf,mute-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; +}; diff --git a/Documentation/devicetree/bindings/sound/zte,zx-i2s.txt b/Documentation/devicetree/bindings/sound/zte,zx-i2s.txt index 292ad5083704..3927251464f0 100644 --- a/Documentation/devicetree/bindings/sound/zte,zx-i2s.txt +++ b/Documentation/devicetree/bindings/sound/zte,zx-i2s.txt @@ -27,7 +27,6 @@ Example: interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; dmas = <&dma 5>, <&dma 6>; dma-names = "tx", "rx"; - status = "okay"; }; sound { diff --git a/Documentation/devicetree/bindings/sound/zte,zx-spdif.txt b/Documentation/devicetree/bindings/sound/zte,zx-spdif.txt index 989544ea6eb5..b5a5ca4502f9 100644 --- a/Documentation/devicetree/bindings/sound/zte,zx-spdif.txt +++ b/Documentation/devicetree/bindings/sound/zte,zx-spdif.txt @@ -24,5 +24,4 @@ Example: interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; dmas = <&dma 4>; dma-names = "tx"; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/spi/efm32-spi.txt b/Documentation/devicetree/bindings/spi/efm32-spi.txt index 750e29aff9bc..2c1e6a43930b 100644 --- a/Documentation/devicetree/bindings/spi/efm32-spi.txt +++ b/Documentation/devicetree/bindings/spi/efm32-spi.txt @@ -28,7 +28,6 @@ spi1: spi@0x4000c400 { /* USART1 */ clocks = <&cmu 20>; cs-gpios = <&gpio 51 1>; // D3 energymicro,location = <1>; - status = "ok"; ks8851@0 { compatible = "ks8851"; @@ -36,6 +35,5 @@ spi1: spi@0x4000c400 { /* USART1 */ reg = <0>; interrupt-parent = <&boardfpga>; interrupts = <4>; - status = "ok"; }; }; diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index 31b5b21598ff..5bf13960f7f4 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -9,6 +9,7 @@ Required properties: - "fsl,imx31-cspi" for SPI compatible with the one integrated on i.MX31 - "fsl,imx35-cspi" for SPI compatible with the one integrated on i.MX35 - "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51 + - "fsl,imx53-ecspi" for SPI compatible with the one integrated on i.MX53 and later Soc - reg : Offset and length of the register set for the device - interrupts : Should contain CSPI/eCSPI interrupt - cs-gpios : Specifies the gpio pins to be used for chipselects. diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt index b785976fe98a..9ba7c5a273b4 100644 --- a/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt @@ -38,5 +38,4 @@ spi@7000d600 { reset-names = "spi"; dmas = <&apbdma 16>, <&apbdma 16>; dma-names = "rx", "tx"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt index bdf08e6dec9b..c212491929b5 100644 --- a/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt @@ -34,5 +34,4 @@ spi@7000c380 { reset-names = "spi"; dmas = <&apbdma 11>, <&apbdma 11>; dma-names = "rx", "tx"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt index 5db9144a33c8..40d80b93e327 100644 --- a/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt @@ -34,5 +34,4 @@ spi@7000d600 { reset-names = "spi"; dmas = <&apbdma 16>, <&apbdma 16>; dma-names = "rx", "tx"; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/spi/sh-hspi.txt b/Documentation/devicetree/bindings/spi/sh-hspi.txt index 319bad4af875..585fed90376e 100644 --- a/Documentation/devicetree/bindings/spi/sh-hspi.txt +++ b/Documentation/devicetree/bindings/spi/sh-hspi.txt @@ -24,6 +24,5 @@ Example: interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index 64ee489571c4..e865855726a2 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -6,6 +6,7 @@ Required properties: "renesas,msiof-r8a7792" (R-Car V2H) "renesas,msiof-r8a7793" (R-Car M2-N) "renesas,msiof-r8a7794" (R-Car E2) + "renesas,msiof-r8a7795" (R-Car H3) "renesas,msiof-r8a7796" (R-Car M3-W) "renesas,msiof-sh73a0" (SH-Mobile AG5) "renesas,sh-mobile-msiof" (generic SH-Mobile compatibile device) @@ -78,5 +79,4 @@ Example: dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/spi/spi-clps711x.txt b/Documentation/devicetree/bindings/spi/spi-clps711x.txt index 4c3ec13f423f..5122dc7860af 100644 --- a/Documentation/devicetree/bindings/spi/spi-clps711x.txt +++ b/Documentation/devicetree/bindings/spi/spi-clps711x.txt @@ -23,7 +23,6 @@ spi@80000500 { reg = <0x80000500 0x4>; interrupts = <15>; clocks = <&clks CLPS711X_CLK_SPI>; - status = "disabled"; }; syscon3: syscon@80002200 { diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt index ff5893d275a2..13b1fcc8469e 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -39,7 +39,6 @@ dspi0@4002c000 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_dspi0_1>; big-endian; - status = "okay"; sflash: at26df081a@0 { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt index e0318cf92d73..236dcb0faf37 100644 --- a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt +++ b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt @@ -57,5 +57,4 @@ spi: spi@1100a000 { clock-names = "parent-clk", "sel-clk", "spi-clk"; cs-gpios = <&pio 105 GPIO_ACTIVE_LOW>, <&pio 72 GPIO_ACTIVE_LOW>; mediatek,pad-select = <1>, <0>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt index 4f629cc7634a..df8ec31f2f07 100644 --- a/Documentation/devicetree/bindings/spi/spi-orion.txt +++ b/Documentation/devicetree/bindings/spi/spi-orion.txt @@ -29,7 +29,6 @@ Example: cell-index = <0>; reg = <0x10600 0x28>; interrupts = <23>; - status = "disabled"; }; Example with SPI direct mode support (optionally): @@ -48,7 +47,6 @@ Example with SPI direct mode support (optionally): <MBUS_ID(0x01, 0x9f) 0 0xffffffff>, /* CS6 */ <MBUS_ID(0x01, 0xdf) 0 0xffffffff>; /* CS7 */ interrupts = <23>; - status = "disabled"; }; To enable the direct mode, the board specific 'ranges' property in the diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt index 83da4931d832..6e3ffacbba32 100644 --- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt @@ -6,6 +6,7 @@ and display controllers using the SPI communication interface. Required Properties: - compatible: should be one of the following. + "rockchip,rv1108-spi" for rv1108 SoCs. "rockchip,rk3036-spi" for rk3036 SoCS. "rockchip,rk3066-spi" for rk3066 SoCs. "rockchip,rk3188-spi" for rk3188 SoCs. diff --git a/Documentation/devicetree/bindings/spi/spi-sun4i.txt b/Documentation/devicetree/bindings/spi/spi-sun4i.txt index de827f5a301e..484bbff5337e 100644 --- a/Documentation/devicetree/bindings/spi/spi-sun4i.txt +++ b/Documentation/devicetree/bindings/spi/spi-sun4i.txt @@ -18,7 +18,6 @@ spi1: spi@01c06000 { interrupts = <11>; clocks = <&ahb_gates 21>, <&spi1_clk>; clock-names = "ahb", "mod"; - status = "disabled"; #address-cells = <1>; #size-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/spi/spi-sun6i.txt b/Documentation/devicetree/bindings/spi/spi-sun6i.txt index 2ec99b86b622..ab1811354cce 100644 --- a/Documentation/devicetree/bindings/spi/spi-sun6i.txt +++ b/Documentation/devicetree/bindings/spi/spi-sun6i.txt @@ -39,7 +39,6 @@ spi0: spi@01c68000 { pinctrl-names = "default"; pinctrl-0 = <&spi0_pins>; resets = <&ccu RST_BUS_SPI0>; - status = "disabled"; #address-cells = <1>; #size-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/spi/spi_atmel.txt b/Documentation/devicetree/bindings/spi/spi_atmel.txt index fb588b3e6a9a..f99c733d75c1 100644 --- a/Documentation/devicetree/bindings/spi/spi_atmel.txt +++ b/Documentation/devicetree/bindings/spi/spi_atmel.txt @@ -26,7 +26,6 @@ spi1: spi@fffcc000 { clock-names = "spi_clk"; cs-gpios = <&pioB 3 0>; atmel,fifo-size = <32>; - status = "okay"; mmc-slot@0 { compatible = "mmc-spi-slot"; diff --git a/Documentation/devicetree/bindings/sram/renesas,smp-sram.txt b/Documentation/devicetree/bindings/sram/renesas,smp-sram.txt new file mode 100644 index 000000000000..712d05e3e15e --- /dev/null +++ b/Documentation/devicetree/bindings/sram/renesas,smp-sram.txt @@ -0,0 +1,27 @@ +* Renesas SMP SRAM + +Renesas R-Car Gen2 and RZ/G1 SoCs need a small piece of SRAM for the jump stub +for secondary CPU bringup and CPU hotplug. +This memory is reserved by adding a child node to a "mmio-sram" node, cfr. +Documentation/devicetree/bindings/sram/sram.txt. + +Required child node properties: + - compatible: Must be "renesas,smp-sram", + - reg: Address and length of the reserved SRAM. + The full physical (bus) address must be aligned to a 256 KiB boundary. + + +Example: + + icram1: sram@e63c0000 { + compatible = "mmio-sram"; + reg = <0 0xe63c0000 0 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0xe63c0000 0x1000>; + + smp-sram@0 { + compatible = "renesas,smp-sram"; + reg = <0 0x10>; + }; + }; diff --git a/Documentation/devicetree/bindings/sram/sunxi-sram.txt b/Documentation/devicetree/bindings/sram/sunxi-sram.txt index 8d5665468fe7..6bb92a1df753 100644 --- a/Documentation/devicetree/bindings/sram/sunxi-sram.txt +++ b/Documentation/devicetree/bindings/sram/sunxi-sram.txt @@ -9,7 +9,9 @@ Controller Node --------------- Required properties: -- compatible : "allwinner,sun4i-a10-sram-controller" +- compatible : should be: + - "allwinner,sun4i-a10-sram-controller" + - "allwinner,sun50i-a64-sram-controller" - reg : sram controller register offset + length SRAM nodes @@ -22,10 +24,13 @@ Each SRAM will have SRAM sections that are going to be handled by the SRAM controller as subnodes. These sections are represented following once again the representation described in the mmio-sram binding. -The valid sections compatible are: +The valid sections compatible for A10 are: - allwinner,sun4i-a10-sram-a3-a4 - allwinner,sun4i-a10-sram-d +The valid sections compatible for A64 are: + - allwinner,sun50i-a64-sram-c + Devices using SRAM sections --------------------------- @@ -59,7 +64,6 @@ sram-controller@01c00000 { emac_sram: sram-section@8000 { compatible = "allwinner,sun4i-a10-sram-a3-a4"; reg = <0x8000 0x4000>; - status = "disabled"; }; }; }; diff --git a/Documentation/devicetree/bindings/thermal/armada-thermal.txt b/Documentation/devicetree/bindings/thermal/armada-thermal.txt index 4698e0edc205..24aacf8948c5 100644 --- a/Documentation/devicetree/bindings/thermal/armada-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/armada-thermal.txt @@ -20,5 +20,4 @@ Example: compatible = "marvell,armada370-thermal"; reg = <0xd0018300 0x4 0xd0018304 0x4>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt index 70b4c16c7ed8..9b4c7b017495 100644 --- a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt @@ -77,7 +77,6 @@ Example 1): interrupts = <2 4>; clocks = <&clock 383>; clock-names = "tmu_apbif"; - status = "disabled"; vtmu-supply = <&tmu_regulator_node>; #include "exynos4412-tmu-sensor-conf.dtsi" }; diff --git a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt index e2f494d74d8a..0d73ea5e9c0c 100644 --- a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt @@ -11,6 +11,7 @@ Required properties: - compatible: - "mediatek,mt8173-thermal" : For MT8173 family of SoCs - "mediatek,mt2701-thermal" : For MT2701 family of SoCs + - "mediatek,mt2712-thermal" : For MT2712 family of SoCs - reg: Address range of the thermal controller - interrupts: IRQ for the thermal controller - clocks, clock-names: Clocks needed for the thermal controller. required diff --git a/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt index 07a9713ae6a7..fdf5caa6229b 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt @@ -36,7 +36,6 @@ Example: clocks = <&cpg CPG_MOD 522>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; #thermal-sensor-cells = <1>; - status = "okay"; }; thermal-zones { diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt index 43003aec94bd..e3a6234fb1ac 100644 --- a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt @@ -4,6 +4,7 @@ Required properties: - compatible : should be "rockchip,<name>-tsadc" "rockchip,rk3228-tsadc": found on RK3228 SoCs "rockchip,rk3288-tsadc": found on RK3288 SoCs + "rockchip,rk3328-tsadc": found on RK3328 SoCs "rockchip,rk3368-tsadc": found on RK3368 SoCs "rockchip,rk3399-tsadc": found on RK3399 SoCs - reg : physical base address of the controller and length of memory mapped diff --git a/Documentation/devicetree/bindings/thermal/uniphier-thermal.txt b/Documentation/devicetree/bindings/thermal/uniphier-thermal.txt new file mode 100644 index 000000000000..686c0b42ed3f --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/uniphier-thermal.txt @@ -0,0 +1,64 @@ +* UniPhier Thermal bindings + +This describes the devicetree bindings for thermal monitor supported by +PVT(Process, Voltage and Temperature) monitoring unit implemented on Socionext +UniPhier SoCs. + +Required properties: +- compatible : + - "socionext,uniphier-pxs2-thermal" : For UniPhier PXs2 SoC + - "socionext,uniphier-ld20-thermal" : For UniPhier LD20 SoC +- interrupts : IRQ for the temperature alarm +- #thermal-sensor-cells : Should be 0. See ./thermal.txt for details. + +Optional properties: +- socionext,tmod-calibration: A pair of calibrated values referred from PVT, + in case that the values aren't set on SoC, + like a reference board. + +Example: + + sysctrl@61840000 { + compatible = "socionext,uniphier-ld20-sysctrl", + "simple-mfd", "syscon"; + reg = <0x61840000 0x10000>; + ... + pvtctl: pvtctl { + compatible = "socionext,uniphier-ld20-thermal"; + interrupts = <0 3 1>; + #thermal-sensor-cells = <0>; + }; + ... + }; + + thermal-zones { + cpu_thermal { + polling-delay-passive = <250>; /* 250ms */ + polling-delay = <1000>; /* 1000ms */ + thermal-sensors = <&pvtctl>; + + trips { + cpu_crit: cpu_crit { + temperature = <110000>; /* 110C */ + hysteresis = <2000>; + type = "critical"; + }; + cpu_alert: cpu_alert { + temperature = <100000>; /* 100C */ + hysteresis = <2000>; + type = "passive"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu_alert>; + cooling-device = <&cpu0 (-1) (-1)>; + }; + map1 { + trip = <&cpu_alert>; + cooling-device = <&cpu2 (-1) (-1)>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt b/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt new file mode 100644 index 000000000000..b4aa7ddb5b13 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt @@ -0,0 +1,28 @@ +NXP Low Power Timer/Pulse Width Modulation Module (TPM) + +The Timer/PWM Module (TPM) supports input capture, output compare, +and the generation of PWM signals to control electric motor and power +management applications. The counter, compare and capture registers +are clocked by an asynchronous clock that can remain enabled in low +power modes. TPM can support global counter bus where one TPM drives +the counter bus for the others, provided bit width is the same. + +Required properties: + +- compatible : should be "fsl,imx7ulp-tpm" +- reg : Specifies base physical address and size of the register sets + for the clock event device and clock source device. +- interrupts : Should be the clock event device interrupt. +- clocks : The clocks provided by the SoC to drive the timer, must contain + an entry for each entry in clock-names. +- clock-names : Must include the following entries: "igp" and "per". + +Example: +tpm5: tpm@40260000 { + compatible = "fsl,imx7ulp-tpm"; + reg = <0x40260000 0x1000>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7ULP_CLK_NIC1_BUS_DIV>, + <&clks IMX7ULP_CLK_LPTPM5>; + clock-names = "ipg", "per"; +}; diff --git a/Documentation/devicetree/bindings/timer/renesas,cmt.txt b/Documentation/devicetree/bindings/timer/renesas,cmt.txt index 1a05c1b243c1..6ca6b9e582a0 100644 --- a/Documentation/devicetree/bindings/timer/renesas,cmt.txt +++ b/Documentation/devicetree/bindings/timer/renesas,cmt.txt @@ -12,46 +12,29 @@ datasheets. Required Properties: - compatible: must contain one or more of the following: - - "renesas,cmt-32-r8a7740" for the r8a7740 32-bit CMT - (CMT0) - - "renesas,cmt-32-sh7372" for the sh7372 32-bit CMT - (CMT0) - - "renesas,cmt-32-sh73a0" for the sh73a0 32-bit CMT - (CMT0) - - "renesas,cmt-32" for all 32-bit CMT without fast clock support - (CMT0 on sh7372, sh73a0 and r8a7740) - This is a fallback for the above renesas,cmt-32-* entries. - - - "renesas,cmt-32-fast-r8a7740" for the r8a7740 32-bit CMT with fast - clock support (CMT[234]) - - "renesas,cmt-32-fast-sh7372" for the sh7372 32-bit CMT with fast - clock support (CMT[234]) - - "renesas,cmt-32-fast-sh73a0" for the sh73A0 32-bit CMT with fast - clock support (CMT[234]) - - "renesas,cmt-32-fast" for all 32-bit CMT with fast clock support - (CMT[234] on sh7372, sh73a0 and r8a7740) - This is a fallback for the above renesas,cmt-32-fast-* entries. - - - "renesas,cmt-48-sh7372" for the sh7372 48-bit CMT - (CMT1) - "renesas,cmt-48-sh73a0" for the sh73A0 48-bit CMT (CMT1) - "renesas,cmt-48-r8a7740" for the r8a7740 48-bit CMT (CMT1) - "renesas,cmt-48" for all non-second generation 48-bit CMT - (CMT1 on sh7372, sh73a0 and r8a7740) + (CMT1 on sh73a0 and r8a7740) This is a fallback for the above renesas,cmt-48-* entries. - - "renesas,cmt-48-r8a73a4" for the r8a73a4 48-bit CMT - (CMT[01]) - - "renesas,cmt-48-r8a7790" for the r8a7790 48-bit CMT - (CMT[01]) - - "renesas,cmt-48-r8a7791" for the r8a7791 48-bit CMT - (CMT[01]) - - "renesas,cmt-48-gen2" for all second generation 48-bit CMT - (CMT[01] on r8a73a4, r8a7790 and r8a7791) - This is a fallback for the renesas,cmt-48-r8a73a4, - renesas,cmt-48-r8a7790 and renesas,cmt-48-r8a7791 entries. + - "renesas,cmt0-r8a73a4" for the 32-bit CMT0 device included in r8a73a4. + - "renesas,cmt1-r8a73a4" for the 48-bit CMT1 device included in r8a73a4. + - "renesas,cmt0-r8a7790" for the 32-bit CMT0 device included in r8a7790. + - "renesas,cmt1-r8a7790" for the 48-bit CMT1 device included in r8a7790. + - "renesas,cmt0-r8a7791" for the 32-bit CMT0 device included in r8a7791. + - "renesas,cmt1-r8a7791" for the 48-bit CMT1 device included in r8a7791. + - "renesas,cmt0-r8a7793" for the 32-bit CMT0 device included in r8a7793. + - "renesas,cmt1-r8a7793" for the 48-bit CMT1 device included in r8a7793. + - "renesas,cmt0-r8a7794" for the 32-bit CMT0 device included in r8a7794. + - "renesas,cmt1-r8a7794" for the 48-bit CMT1 device included in r8a7794. + + - "renesas,rcar-gen2-cmt0" for 32-bit CMT0 devices included in R-Car Gen2. + - "renesas,rcar-gen2-cmt1" for 48-bit CMT1 devices included in R-Car Gen2. + These are fallbacks for r8a73a4 and all the R-Car Gen2 + entries listed above. - reg: base address and length of the registers block for the timer module. - interrupts: interrupt-specifier for the timer, one per channel. @@ -59,21 +42,29 @@ Required Properties: in clock-names. - clock-names: must contain "fck" for the functional clock. - - renesas,channels-mask: bitmask of the available channels. - -Example: R8A7790 (R-Car H2) CMT0 node - - CMT0 on R8A7790 implements hardware channels 5 and 6 only and names - them channels 0 and 1 in the documentation. +Example: R8A7790 (R-Car H2) CMT0 and CMT1 nodes cmt0: timer@ffca0000 { - compatible = "renesas,cmt-48-r8a7790", "renesas,cmt-48-gen2"; + compatible = "renesas,cmt0-r8a7790", "renesas,rcar-gen2-cmt0"; reg = <0 0xffca0000 0 0x1004>; interrupts = <0 142 IRQ_TYPE_LEVEL_HIGH>, <0 142 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp1_clks R8A7790_CLK_CMT0>; clock-names = "fck"; + }; - renesas,channels-mask = <0x60>; + cmt1: timer@e6130000 { + compatible = "renesas,cmt1-r8a7790", "renesas,rcar-gen2-cmt1"; + reg = <0 0xe6130000 0 0x1004>; + interrupts = <0 120 IRQ_TYPE_LEVEL_HIGH>, + <0 121 IRQ_TYPE_LEVEL_HIGH>, + <0 122 IRQ_TYPE_LEVEL_HIGH>, + <0 123 IRQ_TYPE_LEVEL_HIGH>, + <0 124 IRQ_TYPE_LEVEL_HIGH>, + <0 125 IRQ_TYPE_LEVEL_HIGH>, + <0 126 IRQ_TYPE_LEVEL_HIGH>, + <0 127 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7790_CLK_CMT1>; + clock-names = "fck"; }; diff --git a/Documentation/devicetree/bindings/trivial-devices.txt b/Documentation/devicetree/bindings/trivial-devices.txt index 35f406dd86b6..af284fbd4d23 100644 --- a/Documentation/devicetree/bindings/trivial-devices.txt +++ b/Documentation/devicetree/bindings/trivial-devices.txt @@ -21,6 +21,16 @@ adi,adt7490 +/-1C TDM Extended Temp Range I.C adi,adxl345 Three-Axis Digital Accelerometer adi,adxl346 Three-Axis Digital Accelerometer (backward-compatibility value "adi,adxl345" must be listed too) ams,iaq-core AMS iAQ-Core VOC Sensor +amstaos,tsl2571 AMS/TAOS ALS and proximity sensor +amstaos,tsl2671 AMS/TAOS ALS and proximity sensor +amstaos,tmd2671 AMS/TAOS ALS and proximity sensor +amstaos,tsl2771 AMS/TAOS ALS and proximity sensor +amstaos,tmd2771 AMS/TAOS ALS and proximity sensor +amstaos,tsl2572 AMS/TAOS ALS and proximity sensor +amstaos,tsl2672 AMS/TAOS ALS and proximity sensor +amstaos,tmd2672 AMS/TAOS ALS and proximity sensor +amstaos,tsl2772 AMS/TAOS ALS and proximity sensor +amstaos,tmd2772 AMS/TAOS ALS and proximity sensor at,24c08 i2c serial eeprom (24cxx) atmel,at97sc3204t i2c trusted platform module (TPM) capella,cm32181 CM32181: Ambient Light Sensor @@ -36,7 +46,9 @@ dallas,ds1775 Tiny Digital Thermometer and Thermostat dallas,ds3232 Extremely Accurate I²C RTC with Integrated Crystal and SRAM dallas,ds4510 CPU Supervisor with Nonvolatile Memory and Programmable I/O dallas,ds75 Digital Thermometer and Thermostat +devantech,srf02 Devantech SRF02 ultrasonic ranger in I2C mode devantech,srf08 Devantech SRF08 ultrasonic ranger +devantech,srf10 Devantech SRF10 ultrasonic ranger dlg,da9053 DA9053: flexible system level PMIC with multicore support dlg,da9063 DA9063: system PMIC for quad-core application processors domintech,dmard09 DMARD09: 3-axis Accelerometer @@ -54,6 +66,7 @@ fsl,sgtl5000 SGTL5000: Ultra Low-Power Audio Codec gmt,g751 G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire Interface infineon,slb9635tt Infineon SLB9635 (Soft-) I2C TPM (old protocol, max 100khz) infineon,slb9645tt Infineon SLB9645 I2C TPM (new protocol, max 400khz) +isil,isl1208 Intersil ISL1208 Low Power RTC with Battery Backed SRAM isil,isl29028 Intersil ISL29028 Ambient Light and Proximity Sensor isil,isl29030 Intersil ISL29030 Ambient Light and Proximity Sensor maxim,ds1050 5 Bit Programmable, Pulse-Width Modulator @@ -168,6 +181,7 @@ st,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS taos,tsl2550 Ambient Light Sensor with SMBUS/Two Wire Serial Interface ti,ads7828 8-Channels, 12-bit ADC ti,ads7830 8-Channels, 8-bit ADC +ti,amc6821 Temperature Monitoring and Fan Control ti,tsc2003 I2C Touch-Screen Controller ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface ti,tmp103 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface diff --git a/Documentation/devicetree/bindings/unittest.txt b/Documentation/devicetree/bindings/unittest.txt index 3bf58c20fe94..9a5b311f4434 100644 --- a/Documentation/devicetree/bindings/unittest.txt +++ b/Documentation/devicetree/bindings/unittest.txt @@ -10,7 +10,6 @@ All other properties are optional. Example: unittest { compatible = "unittest"; - status = "okay"; }; 2) OF unittest i2c adapter platform device @@ -25,7 +24,6 @@ Children nodes contain unittest i2c devices. Example: unittest-i2c-bus { compatible = "unittest-i2c-bus"; - status = "okay"; }; 3) OF unittest i2c device @@ -40,7 +38,6 @@ All other properties are optional Example: unittest-i2c-dev { compatible = "unittest-i2c-dev"; - status = "okay"; }; 4) OF unittest i2c mux device @@ -55,7 +52,6 @@ Children nodes contain unittest i2c bus nodes per channel. Example: unittest-i2c-mux { compatible = "unittest-i2c-mux"; - status = "okay"; #address-cells = <1>; #size-cells = <0>; channel-0 { @@ -65,7 +61,6 @@ Example: i2c-dev { reg = <8>; compatible = "unittest-i2c-dev"; - status = "okay"; }; }; }; diff --git a/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt b/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt index d9b42da016f3..cb2bd83fa89a 100644 --- a/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt +++ b/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt @@ -25,5 +25,4 @@ Example: phys = <&usbphy 0>; phy-names = "usb"; extcon = <&usbphy 0>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt index 20c2ff2ba07e..16920d78e1b8 100644 --- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt +++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt @@ -4,9 +4,9 @@ - reg: offset and length of the usbss register sets - ti,hwmods : must be "usb_otg_hs" -The glue layer contains multiple child nodes. It is required the have +The glue layer contains multiple child nodes. It is required to have at least a control module node, USB node and a PHY node. The second USB -node and its PHY node is optional. The DMA node is also optional. +node and its PHY node are optional. The DMA node is also optional. Reset module ~~~~~~~~~~~~ diff --git a/Documentation/devicetree/bindings/usb/brcm,bdc.txt b/Documentation/devicetree/bindings/usb/brcm,bdc.txt new file mode 100644 index 000000000000..63e63af3bf59 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/brcm,bdc.txt @@ -0,0 +1,29 @@ +Broadcom USB Device Controller (BDC) +==================================== + +Required properties: + +- compatible: must be one of: + "brcm,bdc-v0.16" + "brcm,bdc" +- reg: the base register address and length +- interrupts: the interrupt line for this controller + +Optional properties: + +On Broadcom STB platforms, these properties are required: + +- phys: phandle to one or two USB PHY blocks + NOTE: Some SoC's have a single phy and some have + USB 2.0 and USB 3.0 phys +- clocks: phandle to the functional clock of this block + +Example: + + bdc@f0b02000 { + compatible = "brcm,bdc-v0.16"; + reg = <0xf0b02000 0xfc4>; + interrupts = <0x0 0x60 0x0>; + phys = <&usbphy_0 0x0>; + clocks = <&sw_usbd>; + }; diff --git a/Documentation/devicetree/bindings/usb/da8xx-usb.txt b/Documentation/devicetree/bindings/usb/da8xx-usb.txt index 717c5f656237..9ce22551b2b3 100644 --- a/Documentation/devicetree/bindings/usb/da8xx-usb.txt +++ b/Documentation/devicetree/bindings/usb/da8xx-usb.txt @@ -42,7 +42,6 @@ Example: usb_phy: usb-phy { compatible = "ti,da830-usb-phy"; #phy-cells = <0>; - status = "okay"; }; usb0: usb@200000 { compatible = "ti,da830-musb"; @@ -66,7 +65,6 @@ Example: "rx1", "rx2", "rx3", "rx4", "tx1", "tx2", "tx3", "tx4"; - status = "okay"; cppi41dma: dma-controller@201000 { compatible = "ti,da830-cppi41"; diff --git a/Documentation/devicetree/bindings/usb/dwc3-st.txt b/Documentation/devicetree/bindings/usb/dwc3-st.txt index 50dee3b44665..df0e02e1ee43 100644 --- a/Documentation/devicetree/bindings/usb/dwc3-st.txt +++ b/Documentation/devicetree/bindings/usb/dwc3-st.txt @@ -42,7 +42,6 @@ or "device". Example: st_dwc3: dwc3@8f94000 { - status = "disabled"; compatible = "st,stih407-dwc3"; reg = <0x08f94000 0x1000>, <0x110 0x4>; reg-names = "reg-glue", "syscfg-reg"; diff --git a/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt b/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt index 30361b32a460..4aae5b2cef56 100644 --- a/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt +++ b/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt @@ -18,7 +18,6 @@ Example device node: usb@0 { #address-cells = <0x2>; #size-cells = <0x1>; - status = "okay"; compatible = "xlnx,zynqmp-dwc3"; clock-names = "bus_clk" "ref_clk"; clocks = <&clk125>, <&clk125>; diff --git a/Documentation/devicetree/bindings/usb/ehci-st.txt b/Documentation/devicetree/bindings/usb/ehci-st.txt index 410d922cfdd7..9feea6c3e4d9 100644 --- a/Documentation/devicetree/bindings/usb/ehci-st.txt +++ b/Documentation/devicetree/bindings/usb/ehci-st.txt @@ -31,7 +31,6 @@ Example: clocks = <&clk_s_a1_ls 0>; phys = <&usb2_phy>; phy-names = "usb"; - status = "okay"; resets = <&powerdown STIH416_USB1_POWERDOWN>, <&softreset STIH416_USB1_SOFTRESET>; diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt index 78ebebb66dad..c97374315049 100644 --- a/Documentation/devicetree/bindings/usb/exynos-usb.txt +++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt @@ -40,7 +40,6 @@ Example: port@0 { reg = <0>; phys = <&usb2phy 1>; - status = "disabled"; }; }; @@ -75,7 +74,6 @@ Example: port@0 { reg = <0>; phys = <&usb2phy 1>; - status = "disabled"; }; }; diff --git a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt new file mode 100644 index 000000000000..472facfa5a71 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt @@ -0,0 +1,29 @@ +Fairchild FUSB302 Type-C Port controllers + +Required properties : +- compatible : "fcs,fusb302" +- reg : I2C slave address +- interrupts : Interrupt specifier + +Optional properties : +- fcs,max-sink-microvolt : Maximum voltage to negotiate when configured as sink +- fcs,max-sink-microamp : Maximum current to negotiate when configured as sink +- fcs,max-sink-microwatt : Maximum power to negotiate when configured as sink + If this is less then max-sink-microvolt * + max-sink-microamp then the configured current will + be clamped. +- fcs,operating-sink-microwatt : + Minimum amount of power accepted from a sink + when negotiating + +Example: + +fusb302: typec-portc@54 { + compatible = "fcs,fusb302"; + reg = <0x54>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + fcs,max-sink-microvolt = <12000000>; + fcs,max-sink-microamp = <3000000>; + fcs,max-sink-microwatt = <36000000>; +}; diff --git a/Documentation/devicetree/bindings/usb/isp1301.txt b/Documentation/devicetree/bindings/usb/isp1301.txt index 5405d99d9aaa..ecd607dacba5 100644 --- a/Documentation/devicetree/bindings/usb/isp1301.txt +++ b/Documentation/devicetree/bindings/usb/isp1301.txt @@ -21,5 +21,4 @@ Example: interrupt-parent = <&mic>; interrupts = <0x3d 0>, <0x3e 0>, <0x3c 0>, <0x3a 0>; transceiver = <&isp1301>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/usb/keystone-usb.txt b/Documentation/devicetree/bindings/usb/keystone-usb.txt index 60527d335b58..f96e09f784cc 100644 --- a/Documentation/devicetree/bindings/usb/keystone-usb.txt +++ b/Documentation/devicetree/bindings/usb/keystone-usb.txt @@ -12,8 +12,21 @@ Required properties: MPU. - ranges: allows valid 1:1 translation between child's address space and parent's address space. - - clocks: Clock IDs array as required by the controller. - - clock-names: names of clocks correseponding to IDs in the clock property. + +SoC-specific Required Properties: +The following are mandatory properties for Keystone 2 66AK2HK, 66AK2L and 66AK2E +SoCs only: + +- clocks: Clock ID for USB functional clock. +- clock-names: Must be "usb". + + +The following are mandatory properties for Keystone 2 66AK2G SoCs only: + +- power-domains: Should contain a phandle to a PM domain provider node + and an args specifier containing the USB device id + value. This property is as per the binding, + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt Sub-nodes: The dwc3 core should be added as subnode to Keystone DWC3 glue. @@ -31,7 +44,6 @@ Example: clock-names = "usb"; interrupts = <GIC_SPI 393 IRQ_TYPE_EDGE_RISING>; ranges; - status = "disabled"; dwc3@2690000 { compatible = "synopsys,dwc3"; diff --git a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt index 0acfc8acbea1..5611a2e4ddf0 100644 --- a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt +++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt @@ -11,7 +11,11 @@ into two parts. ------------------------------------------------------------------------ Required properties: - - compatible : should contain "mediatek,mt8173-xhci" + - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci", + soc-model is the name of SoC, such as mt8173, mt2712 etc, when using + "mediatek,mtk-xhci" compatible string, you need SoC specific ones in + addition, one of: + - "mediatek,mt8173-xhci" - reg : specifies physical base address and size of the registers - reg-names: should be "mac" for xHCI MAC and "ippc" for IP port control - interrupts : interrupt used by the controller @@ -68,10 +72,14 @@ usb30: usb@11270000 { In the case, xhci is added as subnode to mtu3. An example and the DT binding details of mtu3 can be found in: -Documentation/devicetree/bindings/usb/mt8173-mtu3.txt +Documentation/devicetree/bindings/usb/mediatek,mtu3.txt Required properties: - - compatible : should contain "mediatek,mt8173-xhci" + - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci", + soc-model is the name of SoC, such as mt8173, mt2712 etc, when using + "mediatek,mtk-xhci" compatible string, you need SoC specific ones in + addition, one of: + - "mediatek,mt8173-xhci" - reg : specifies physical base address and size of the registers - reg-names: should be "mac" for xHCI MAC - interrupts : interrupt used by the host controller diff --git a/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt index 1d7c3bc677f7..49f54767cd21 100644 --- a/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt +++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt @@ -1,7 +1,11 @@ The device node for Mediatek USB3.0 DRD controller Required properties: - - compatible : should be "mediatek,mt8173-mtu3" + - compatible : should be "mediatek,<soc-model>-mtu3", "mediatek,mtu3", + soc-model is the name of SoC, such as mt8173, mt2712 etc, + when using "mediatek,mtu3" compatible string, you need SoC specific + ones in addition, one of: + - "mediatek,mt8173-mtu3" - reg : specifies physical base address and size of the registers - reg-names: should be "mac" for device IP and "ippc" for IP port control - interrupts : interrupt used by the device IP @@ -44,7 +48,7 @@ Optional properties: Sub-nodes: The xhci should be added as subnode to mtu3 as shown in the following example if host mode is enabled. The DT binding details of xhci can be found in: -Documentation/devicetree/bindings/usb/mt8173-xhci.txt +Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt Example: ssusb: usb@11271000 { @@ -71,7 +75,6 @@ ssusb: usb@11271000 { #address-cells = <2>; #size-cells = <2>; ranges; - status = "disabled"; usb_host: xhci@11270000 { compatible = "mediatek,mt8173-xhci"; @@ -82,6 +85,5 @@ ssusb: usb@11271000 { clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; clock-names = "sys_ck", "ref_ck"; vusb33-supply = <&mt6397_vusb_reg>; - status = "disabled"; }; }; diff --git a/Documentation/devicetree/bindings/usb/ohci-st.txt b/Documentation/devicetree/bindings/usb/ohci-st.txt index 6d8393748da2..d893ec9131c3 100644 --- a/Documentation/devicetree/bindings/usb/ohci-st.txt +++ b/Documentation/devicetree/bindings/usb/ohci-st.txt @@ -29,7 +29,6 @@ Example: clock-names = "ic", "clk48"; phys = <&usb2_phy>; phy-names = "usb"; - status = "okay"; resets = <&powerdown STIH416_USB0_POWERDOWN>, <&softreset STIH416_USB0_SOFTRESET>; diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt index 73cc0963e823..bc8a2fa5d2bf 100644 --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt @@ -29,7 +29,6 @@ Example device nodes: clock-names = "ref"; #phy-cells = <0>; - status = "ok"; }; ss_phy: phy@100f8830 { @@ -39,7 +38,6 @@ Example device nodes: clock-names = "ref"; #phy-cells = <0>; - status = "ok"; }; usb3_0: usb30@0 { @@ -51,7 +49,6 @@ Example device nodes: ranges; - status = "ok"; dwc3@10000000 { compatible = "snps,dwc3"; diff --git a/Documentation/devicetree/bindings/usb/renesas_usb3.txt b/Documentation/devicetree/bindings/usb/renesas_usb3.txt index 8d52766f07b9..e28025883b79 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usb3.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usb3.txt @@ -3,20 +3,30 @@ Renesas Electronics USB3.0 Peripheral driver Required properties: - compatible: Must contain one of the following: - "renesas,r8a7795-usb3-peri" + - "renesas,r8a7796-usb3-peri" + - "renesas,rcar-gen3-usb3-peri" for a generic R-Car Gen3 compatible + device + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: Base address and length of the register for the USB3.0 Peripheral - interrupts: Interrupt specifier for the USB3.0 Peripheral - clocks: clock phandle and specifier pair -Example: +Example of R-Car H3 ES1.x: usb3_peri0: usb@ee020000 { - compatible = "renesas,r8a7795-usb3-peri"; + compatible = "renesas,r8a7795-usb3-peri", + "renesas,rcar-gen3-usb3-peri"; reg = <0 0xee020000 0 0x400>; interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 328>; }; usb3_peri1: usb@ee060000 { - compatible = "renesas,r8a7795-usb3-peri"; + compatible = "renesas,r8a7795-usb3-peri", + "renesas,rcar-gen3-usb3-peri"; reg = <0 0xee060000 0 0x400>; interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 327>; diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt index 0536a938e3ab..50a31536e975 100644 --- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt @@ -29,13 +29,11 @@ Example device nodes: #address-cells = <2>; #size-cells = <2>; ranges; - status = "disabled"; usbdrd_dwc3_0: dwc3@fe800000 { compatible = "snps,dwc3"; reg = <0x0 0xfe800000 0x0 0x100000>; interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; dr_mode = "otg"; - status = "disabled"; }; }; @@ -48,12 +46,10 @@ Example device nodes: #address-cells = <2>; #size-cells = <2>; ranges; - status = "disabled"; usbdrd_dwc3_1: dwc3@fe900000 { compatible = "snps,dwc3"; reg = <0x0 0xfe900000 0x0 0x100000>; interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; dr_mode = "otg"; - status = "disabled"; }; }; diff --git a/Documentation/devicetree/bindings/usb/usb-device.txt b/Documentation/devicetree/bindings/usb/usb-device.txt index 1c35e7b665e1..ce02cebac26a 100644 --- a/Documentation/devicetree/bindings/usb/usb-device.txt +++ b/Documentation/devicetree/bindings/usb/usb-device.txt @@ -2,7 +2,7 @@ Generic USB Device Properties Usually, we only use device tree for hard wired USB device. The reference binding doc is from: -http://www.firmware.org/1275/bindings/usb/usb-1_0.ps +http://www.devicetree.org/open-firmware/bindings/usb/usb-1_0.ps Required properties: - compatible: usbVID,PID. The textual representation of VID, PID shall @@ -16,7 +16,6 @@ Required properties: Example: &usb1 { - status = "okay"; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 1dff0b5ca6e4..6cf1dc5bc77e 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -3,12 +3,13 @@ Device tree binding vendor prefix registry. Keep list in alphabetical order. This isn't an exhaustive list, but you should add new prefixes to it before using them to avoid name-space collisions. -abcn Abracon Corporation abilis Abilis Systems +abracon Abracon Corporation actions Actions Semiconductor Co., Ltd. active-semi Active-Semi International Inc ad Avionic Design GmbH adapteva Adapteva, Inc. +adaptrum Adaptrum, Inc. adh AD Holdings Plc. adi Analog Devices, Inc. advantech Advantech Corporation @@ -47,6 +48,7 @@ avic Shanghai AVIC Optoelectronics Co., Ltd. axentia Axentia Technologies AB axis Axis Communications AB bananapi BIPAI KEJI LIMITED +bhf Beckhoff Automation GmbH & Co. KG boe BOE Technology Group Co., Ltd. bosch Bosch Sensortec GmbH boundary Boundary Devices Inc. @@ -88,6 +90,7 @@ dlg Dialog Semiconductor dlink D-Link Corporation dmo Data Modul AG domintech Domintech Co., Ltd. +dongwoon Dongwoon Anatech dptechnics DPTechnics dragino Dragino Technology Co., Limited ea Embedded Artists AB @@ -175,6 +178,7 @@ kosagi Sutajio Ko-Usagi PTE Ltd. kyo Kyocera Corporation lacie LaCie lantiq Lantiq Semiconductor +lattice Lattice Semiconductor lego LEGO Systems A/S lenovo Lenovo Group Ltd. lg LG Corporation @@ -195,6 +199,7 @@ mediatek MediaTek Inc. megachips MegaChips melexis Melexis N.V. melfas MELFAS Inc. +mellanox Mellanox Technologies memsic MEMSIC Inc. merrii Merrii Technology Co., Ltd. micrel Micrel Inc. @@ -206,7 +211,7 @@ miramems MiraMEMS Sensing Technology Co., Ltd. mitsubishi Mitsubishi Electric Corporation mosaixtech Mosaix Technologies, Inc. motorola Motorola, Inc. -moxa Moxa +moxa Moxa Inc. mpl MPL AG mqmaker mqmaker Inc. msi Micro-Star International Co. Ltd. @@ -289,6 +294,7 @@ schindler Schindler seagate Seagate Technology PLC semtech Semtech Corporation sensirion Sensirion AG +sff Small Form Factor Committee sgx SGX Sensortech sharp Sharp Corporation si-en Si-En Technology Ltd. @@ -343,6 +349,7 @@ tpo TPO tronfy Tronfy tronsmart Tronsmart truly Truly Semiconductors Limited +tsd Theobroma Systems Design und Consulting GmbH tyan Tyan Computer Corporation ucrobotics uCRobotics udoo Udoo @@ -355,6 +362,7 @@ variscite Variscite Ltd. via VIA Technologies, Inc. virtio Virtual I/O Device Specification, developed by the OASIS consortium vivante Vivante Corporation +vocore VoCore Studio voipac Voipac Technologies s.r.o. wd Western Digital Corp. wetek WeTek Electronics, limited. diff --git a/Documentation/devicetree/bindings/w1/fsl-imx-owire.txt b/Documentation/devicetree/bindings/w1/fsl-imx-owire.txt index ecf42c07684d..cbaa6467ab2c 100644 --- a/Documentation/devicetree/bindings/w1/fsl-imx-owire.txt +++ b/Documentation/devicetree/bindings/w1/fsl-imx-owire.txt @@ -15,5 +15,4 @@ owire: owire@63fa4000 { compatible = "fsl,imx53-owire", "fsl,imx21-owire"; reg = <0x63fa4000 0x4000>; clocks = <&clks 159>; - status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt b/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt index c5e74d7b4406..c5077a1f5cb3 100644 --- a/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt @@ -8,9 +8,49 @@ Required properties: - reg: physical base address of the controller and length of memory mapped region +Optional properties: + + - aspeed,reset-type = "cpu|soc|system|none" + + Reset behavior - Whenever a timeout occurs the watchdog can be programmed + to generate one of three different, mutually exclusive, types of resets. + + Type "none" can be specified to indicate that no resets are to be done. + This is useful in situations where another watchdog engine on chip is + to perform the reset. + + If 'aspeed,reset-type=' is not specfied the default is to enable system + reset. + + Reset types: + + - cpu: Reset CPU on watchdog timeout + + - soc: Reset 'System on Chip' on watchdog timeout + + - system: Reset system on watchdog timeout + + - none: No reset is performed on timeout. Assumes another watchdog + engine is responsible for this. + + - aspeed,alt-boot: If property is present then boot from alternate block. + - aspeed,external-signal: If property is present then signal is sent to + external reset counter (only WDT1 and WDT2). If not + specified no external signal is sent. + - aspeed,ext-pulse-duration: External signal pulse duration in microseconds + +Optional properties for AST2500-compatible watchdogs: + - aspeed,ext-push-pull: If aspeed,external-signal is present, set the pin's + drive type to push-pull. The default is open-drain. + - aspeed,ext-active-high: If aspeed,external-signal is present and and the pin + is configured as push-pull, then set the pulse + polarity to active-high. The default is active-low. + Example: wdt1: watchdog@1e785000 { compatible = "aspeed,ast2400-wdt"; reg = <0x1e785000 0x1c>; + aspeed,reset-type = "system"; + aspeed,external-signal; }; diff --git a/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt index f7cc7c060910..4fec1e3725b4 100644 --- a/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt @@ -31,5 +31,4 @@ Example: atmel,watchdog-type = "hardware"; atmel,dbg-halt; atmel,idle-halt; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt index 86fa6de1019b..711a880b3d3b 100644 --- a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt @@ -48,5 +48,4 @@ Example: atmel,idle-halt; atmel,max-heartbeat-sec = <16>; atmel,min-heartbeat-sec = <0>; - status = "okay"; }; diff --git a/Documentation/devicetree/bindings/watchdog/lantiq-wdt.txt b/Documentation/devicetree/bindings/watchdog/lantiq-wdt.txt new file mode 100644 index 000000000000..18d4d8302702 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/lantiq-wdt.txt @@ -0,0 +1,24 @@ +Lantiq WTD watchdog binding +============================ + +This describes the binding of the Lantiq watchdog driver. + +------------------------------------------------------------------------------- +Required properties: +- compatible : Should be one of + "lantiq,wdt" + "lantiq,xrx100-wdt" + "lantiq,xrx200-wdt", "lantiq,xrx100-wdt" + "lantiq,falcon-wdt" +- reg : Address of the watchdog block +- lantiq,rcu : A phandle to the RCU syscon (required for + "lantiq,falcon-wdt" and "lantiq,xrx100-wdt") + +------------------------------------------------------------------------------- +Example for the watchdog on the xRX200 SoCs: + watchdog@803f0 { + compatible = "lantiq,xrx200-wdt", "lantiq,xrx100-wdt"; + reg = <0x803f0 0x10>; + + lantiq,rcu = <&rcu0>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/marvel.txt b/Documentation/devicetree/bindings/watchdog/marvel.txt index 858ed9221ac4..c1b67a78f00c 100644 --- a/Documentation/devicetree/bindings/watchdog/marvel.txt +++ b/Documentation/devicetree/bindings/watchdog/marvel.txt @@ -41,6 +41,5 @@ Example: reg = <0x20300 0x28>, <0x20108 0x4>; interrupts = <3>; timeout-sec = <10>; - status = "okay"; clocks = <&gate_clk 7>; }; diff --git a/Documentation/devicetree/bindings/watchdog/meson-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt index ae70185d96e6..8a6d84cb36c9 100644 --- a/Documentation/devicetree/bindings/watchdog/meson-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt @@ -2,7 +2,11 @@ Meson SoCs Watchdog timer Required properties: -- compatible : should be "amlogic,meson6-wdt" or "amlogic,meson8b-wdt" +- compatible : depending on the SoC this should be one of: + "amlogic,meson6-wdt" on Meson6 SoCs + "amlogic,meson8-wdt" and "amlogic,meson6-wdt" on Meson8 SoCs + "amlogic,meson8b-wdt" on Meson8b SoCs + "amlogic,meson8m2-wdt" and "amlogic,meson8b-wdt" on Meson8m2 SoCs - reg : Specifies base physical address and size of the registers. Example: diff --git a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt index 6a00939a059a..235de0683bb6 100644 --- a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt @@ -3,9 +3,11 @@ Mediatek SoCs Watchdog timer Required properties: - compatible should contain: - * "mediatek,mt2701-wdt" for MT2701 compatible watchdog timers - * "mediatek,mt6589-wdt" for all compatible watchdog timers (MT2701, - MT6589) + "mediatek,mt2701-wdt", "mediatek,mt6589-wdt": for MT2701 + "mediatek,mt6589-wdt": for MT6589 + "mediatek,mt6797-wdt", "mediatek,mt6589-wdt": for MT6797 + "mediatek,mt7622-wdt", "mediatek,mt6589-wdt": for MT7622 + "mediatek,mt7623-wdt", "mediatek,mt6589-wdt": for MT7623 - reg : Specifies base physical address and size of the registers. diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt index 9e306afbbd49..bf6d1ca58af7 100644 --- a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt @@ -6,6 +6,7 @@ Required properties: Examples with soctypes are: - "renesas,r8a7795-wdt" (R-Car H3) - "renesas,r8a7796-wdt" (R-Car M3-W) + - "renesas,r8a77995-wdt" (R-Car D3) - "renesas,r7s72100-wdt" (RZ/A1) When compatible with the generic version, nodes must list the SoC-specific diff --git a/Documentation/devicetree/bindings/xilinx.txt b/Documentation/devicetree/bindings/xilinx.txt index 299d0923537b..1d11b9002ef8 100644 --- a/Documentation/devicetree/bindings/xilinx.txt +++ b/Documentation/devicetree/bindings/xilinx.txt @@ -281,6 +281,8 @@ capabilities of the underlying ICAP hardware differ between different families. May be 'virtex2p', 'virtex4', or 'virtex5'. + - compatible : should contain "xlnx,xps-hwicap-1.00.a" or + "xlnx,opb-hwicap-1.00.b". vi) Xilinx Uart 16550 |
