summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/mtd/gpmc-nand.txt')
-rw-r--r--Documentation/devicetree/bindings/mtd/gpmc-nand.txt80
1 files changed, 80 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
new file mode 100644
index 000000000000..e7f8d7ed47eb
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
@@ -0,0 +1,80 @@
+Device tree bindings for GPMC connected NANDs
+
+GPMC connected NAND (found on OMAP boards) are represented as child nodes of
+the GPMC controller with a name of "nand".
+
+All timing relevant properties as well as generic gpmc child properties are
+explained in a separate documents - please refer to
+Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+For NAND specific properties such as ECC modes or bus width, please refer to
+Documentation/devicetree/bindings/mtd/nand.txt
+
+
+Required properties:
+
+ - reg: The CS line the peripheral is connected to
+
+Optional properties:
+
+ - nand-bus-width: Set this numeric value to 16 if the hardware
+ is wired that way. If not specified, a bus
+ width of 8 is assumed.
+
+ - ti,nand-ecc-opt: A string setting the ECC layout to use. One of:
+
+ "sw" Software method (default)
+ "hw" Hardware method
+ "hw-romcode" gpmc hamming mode method & romcode layout
+ "bch4" 4-bit BCH ecc code
+ "bch8" 8-bit BCH ecc code
+
+ - elm_id: Specifies elm device node. This is required to support BCH
+ error correction using ELM module.
+
+For inline partiton table parsing (optional):
+
+ - #address-cells: should be set to 1
+ - #size-cells: should be set to 1
+
+Example for an AM33xx board:
+
+ gpmc: gpmc@50000000 {
+ compatible = "ti,am3352-gpmc";
+ ti,hwmods = "gpmc";
+ reg = <0x50000000 0x1000000>;
+ interrupts = <100>;
+ gpmc,num-cs = <8>;
+ gpmc,num-waitpins = <2>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x2000>; /* CS0: NAND */
+ elm_id = <&elm>;
+
+ nand@0,0 {
+ reg = <0 0 0>; /* CS0, offset 0 */
+ nand-bus-width = <16>;
+ ti,nand-ecc-opt = "bch8";
+
+ gpmc,sync-clk = <0>;
+ gpmc,cs-on = <0>;
+ gpmc,cs-rd-off = <44>;
+ gpmc,cs-wr-off = <44>;
+ gpmc,adv-on = <6>;
+ gpmc,adv-rd-off = <34>;
+ gpmc,adv-wr-off = <44>;
+ gpmc,we-off = <40>;
+ gpmc,oe-off = <54>;
+ gpmc,access = <64>;
+ gpmc,rd-cycle = <82>;
+ gpmc,wr-cycle = <82>;
+ gpmc,wr-access = <40>;
+ gpmc,wr-data-mux-bus = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* partitions go here */
+ };
+ };
+
OpenPOWER on IntegriCloud