[media] common: move media/common/tuners to media/tuners

Move the tuners one level up, as the "common" directory will be used
by drivers that are shared between more than one driver.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

1 files changed, 104 insertions, 0 deletions

diff --git a/drivers/media/tuners/mt2060_priv.h b/drivers/media/tuners/mt2060_priv.h
new file mode 100644
index 000000000000..2b60de6c707d
--- /dev/null
+++ b/drivers/media/tuners/mt2060_priv.h
@@ -0,0 +1,104 @@
+/*
+ *  Driver for Microtune MT2060 "Single chip dual conversion broadband tuner"
+ *
+ *  Copyright (c) 2006 Olivier DANET <odanet@caramail.com>
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.=
+ */
+
+#ifndef MT2060_PRIV_H
+#define MT2060_PRIV_H
+
+// Uncomment the #define below to enable spurs checking. The results where quite unconvincing.
+// #define MT2060_SPURCHECK
+
+/* This driver is based on the information available in the datasheet of the
+   "Comtech SDVBT-3K6M" tuner ( K1000737843.pdf ) which features the MT2060 register map :
+
+   I2C Address : 0x60
+
+   Reg.No |   B7   |   B6   |   B5   |   B4   |   B3   |   B2   |   B1   |   B0   | ( defaults )
+   --------------------------------------------------------------------------------
+       00 | [              PART             ] | [              REV              ] | R  = 0x63
+       01 | [             LNABAND           ] | [              NUM1(5:2)        ] | RW = 0x3F
+       02 | [                               DIV1                                ] | RW = 0x74
+       03 | FM1CA  | FM1SS  | [  NUM1(1:0)  ] | [              NUM2(3:0)        ] | RW = 0x00
+       04 |                                 NUM2(11:4)                          ] | RW = 0x08
+       05 | [                               DIV2                       ] |NUM2(12)| RW = 0x93
+       06 | L1LK   | [        TAD1          ] | L2LK   | [         TAD2         ] | R
+       07 | [                               FMF                                 ] | R
+       08 |   ?    | FMCAL  |   ?    |   ?    |   ?    |   ?    |   ?    | TEMP   | R
+       09 |   0    |   0    | [    FMGC     ] |   0    | GP02   | GP01   |   0    | RW = 0x20
+       0A | ??
+       0B |   0    |   0    |   1    |   1    |   0    |   0    | [   VGAG      ] | RW = 0x30
+       0C | V1CSE  |   1    |   1    |   1    |   1    |   1    |   1    |   1    | RW = 0xFF
+       0D |   1    |   0    | [                      V1CS                       ] | RW = 0xB0
+       0E | ??
+       0F | ??
+       10 | ??
+       11 | [             LOTO              ] |   0    |   0    |   1    |   0    | RW = 0x42
+
+       PART    : Part code      : 6 for MT2060
+       REV     : Revision code  : 3 for current revision
+       LNABAND : Input frequency range : ( See code for details )
+       NUM1 / DIV1 / NUM2 / DIV2 : Frequencies programming ( See code for details )
+       FM1CA  : Calibration Start Bit
+       FM1SS  : Calibration Single Step bit
+       L1LK   : LO1 Lock Detect
+       TAD1   : Tune Line ADC ( ? )
+       L2LK   : LO2 Lock Detect
+       TAD2   : Tune Line ADC ( ? )
+       FMF    : Estimated first IF Center frequency Offset ( ? )
+       FM1CAL : Calibration done bit
+       TEMP   : On chip temperature sensor
+       FMCG   : Mixer 1 Cap Gain ( ? )
+       GP01 / GP02 : Programmable digital outputs. Unconnected pins ?
+       V1CSE  : LO1 VCO Automatic Capacitor Select Enable ( ? )
+       V1CS   : LO1 Capacitor Selection Value ( ? )
+       LOTO   : LO Timeout ( ? )
+       VGAG   : Tuner Output gain
+*/
+
+#define I2C_ADDRESS 0x60
+
+#define REG_PART_REV   0
+#define REG_LO1C1      1
+#define REG_LO1C2      2
+#define REG_LO2C1      3
+#define REG_LO2C2      4
+#define REG_LO2C3      5
+#define REG_LO_STATUS  6
+#define REG_FM_FREQ    7
+#define REG_MISC_STAT  8
+#define REG_MISC_CTRL  9
+#define REG_RESERVED_A 0x0A
+#define REG_VGAG       0x0B
+#define REG_LO1B1      0x0C
+#define REG_LO1B2      0x0D
+#define REG_LOTO       0x11
+
+#define PART_REV 0x63 // The current driver works only with PART=6 and REV=3 chips
+
+struct mt2060_priv {
+	struct mt2060_config *cfg;
+	struct i2c_adapter   *i2c;
+
+	u32 frequency;
+	u16 if1_freq;
+	u8  fmfreq;
+};
+
+#endif