1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
|
LIS302 accelerometer devicetree bindings
This device is matched via its bus drivers, and has a number of properties
that apply in on the generic device (independent from the bus).
Required properties for the SPI bindings:
- compatible: should be set to "st,lis3lv02d_spi"
- reg: the chipselect index
- spi-max-frequency: maximal bus speed, should be set to 1000000 unless
constrained by external circuitry
- interrupts: the interrupt generated by the device
Required properties for the I2C bindings:
- compatible: should be set to "st,lis3lv02d"
- reg: i2c slave address
- Vdd-supply: The input supply for Vdd
- Vdd_IO-supply: The input supply for Vdd_IO
Optional properties for all bus drivers:
- st,click-single-{x,y,z}: if present, tells the device to issue an
interrupt on single click events on the
x/y/z axis.
- st,click-double-{x,y,z}: if present, tells the device to issue an
interrupt on double click events on the
x/y/z axis.
- st,click-thresh-{x,y,z}: set the x/y/z axis threshold
- st,click-click-time-limit: click time limit, from 0 to 127.5msec
with step of 0.5 msec
- st,click-latency: click latency, from 0 to 255 msec with
step of 1 msec.
- st,click-window: click window, from 0 to 255 msec with
step of 1 msec.
- st,irq{1,2}-disable: disable IRQ 1/2
- st,irq{1,2}-ff-wu-1: raise IRQ 1/2 on FF_WU_1 condition
- st,irq{1,2}-ff-wu-2: raise IRQ 1/2 on FF_WU_2 condition
- st,irq{1,2}-data-ready: raise IRQ 1/2 on data ready contition
- st,irq{1,2}-click: raise IRQ 1/2 on click condition
- st,irq-open-drain: consider IRQ lines open-drain
- st,irq-active-low: make IRQ lines active low
- st,wu-duration-1: duration register for Free-Fall/Wake-Up
interrupt 1
- st,wu-duration-2: duration register for Free-Fall/Wake-Up
interrupt 2
- st,wakeup-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for
upper/lower limit
- st,highpass-cutoff-hz=: 1, 2, 4 or 8 for 1Hz, 2Hz, 4Hz or 8Hz of
highpass cut-off frequency
- st,hipass{1,2}-disable: disable highpass 1/2.
- st,default-rate=: set the default rate
- st,axis-{x,y,z}=: set the axis to map to the three coordinates
- st,{min,max}-limit-{x,y,z} set the min/max limits for x/y/z axis
(used by self-test)
Example for a SPI device node:
lis302@0 {
compatible = "st,lis302dl-spi";
reg = <0>;
spi-max-frequency = <1000000>;
interrupt-parent = <&gpio>;
interrupts = <104 0>;
st,click-single-x;
st,click-single-y;
st,click-single-z;
st,click-thresh-x = <10>;
st,click-thresh-y = <10>;
st,click-thresh-z = <10>;
st,irq1-click;
st,irq2-click;
st,wakeup-x-lo;
st,wakeup-x-hi;
st,wakeup-y-lo;
st,wakeup-y-hi;
st,wakeup-z-lo;
st,wakeup-z-hi;
};
Example for a I2C device node:
lis331dlh: lis331dlh@18 {
compatible = "st,lis331dlh", "st,lis3lv02d";
reg = <0x18>;
Vdd-supply = <&lis3_reg>;
Vdd_IO-supply = <&lis3_reg>;
st,click-single-x;
st,click-single-y;
st,click-single-z;
st,click-thresh-x = <10>;
st,click-thresh-y = <10>;
st,click-thresh-z = <10>;
st,irq1-click;
st,irq2-click;
st,wakeup-x-lo;
st,wakeup-x-hi;
st,wakeup-y-lo;
st,wakeup-y-hi;
st,wakeup-z-lo;
st,wakeup-z-hi;
st,min-limit-x = <120>;
st,min-limit-y = <120>;
st,min-limit-z = <140>;
st,max-limit-x = <550>;
st,max-limit-y = <550>;
st,max-limit-z = <750>;
};
|
