diff options
Diffstat (limited to 'drivers/serial')
| -rw-r--r-- | drivers/serial/8250.c | 4 | ||||
| -rw-r--r-- | drivers/serial/Makefile | 1 | ||||
| -rw-r--r-- | drivers/serial/bfin_5xx.c | 2 | ||||
| -rw-r--r-- | drivers/serial/cpm_uart/cpm_uart.h | 11 | ||||
| -rw-r--r-- | drivers/serial/cpm_uart/cpm_uart_core.c | 66 | ||||
| -rw-r--r-- | drivers/serial/crisv10.c | 79 | ||||
| -rw-r--r-- | drivers/serial/crisv10.h | 3 | ||||
| -rw-r--r-- | drivers/serial/sh-sci.c | 17 | ||||
| -rw-r--r-- | drivers/serial/sh-sci.h | 40 | ||||
| -rw-r--r-- | drivers/serial/v850e_uart.c | 548 |
10 files changed, 157 insertions, 614 deletions
diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c index a97f1ae11f78..342e12fb1c25 100644 --- a/drivers/serial/8250.c +++ b/drivers/serial/8250.c @@ -1885,7 +1885,7 @@ static int serial8250_startup(struct uart_port *port) * the interrupt is enabled. Delays are necessary to * allow register changes to become visible. */ - spin_lock(&up->port.lock); + spin_lock_irqsave(&up->port.lock, flags); if (up->port.flags & UPF_SHARE_IRQ) disable_irq_nosync(up->port.irq); @@ -1901,7 +1901,7 @@ static int serial8250_startup(struct uart_port *port) if (up->port.flags & UPF_SHARE_IRQ) enable_irq(up->port.irq); - spin_unlock(&up->port.lock); + spin_unlock_irqrestore(&up->port.lock, flags); /* * If the interrupt is not reasserted, setup a timer to diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile index 3a0bbbe17aa3..7e7383e890d8 100644 --- a/drivers/serial/Makefile +++ b/drivers/serial/Makefile @@ -42,7 +42,6 @@ obj-$(CONFIG_SERIAL_68328) += 68328serial.o obj-$(CONFIG_SERIAL_68360) += 68360serial.o obj-$(CONFIG_SERIAL_COLDFIRE) += mcfserial.o obj-$(CONFIG_SERIAL_MCF) += mcf.o -obj-$(CONFIG_V850E_UART) += v850e_uart.o obj-$(CONFIG_SERIAL_PMACZILOG) += pmac_zilog.o obj-$(CONFIG_SERIAL_LH7A40X) += serial_lh7a40x.o obj-$(CONFIG_SERIAL_DZ) += dz.o diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c index 9d8543762a30..efcd44344fb1 100644 --- a/drivers/serial/bfin_5xx.c +++ b/drivers/serial/bfin_5xx.c @@ -817,7 +817,7 @@ static void bfin_serial_set_ldisc(struct uart_port *port) if (line >= port->info->port.tty->driver->num) return; - switch (port->info->port.tty->ldisc.num) { + switch (port->info->port.tty->termios->c_line) { case N_IRDA: val = UART_GET_GCTL(&bfin_serial_ports[line]); val |= (IREN | RPOLC); diff --git a/drivers/serial/cpm_uart/cpm_uart.h b/drivers/serial/cpm_uart/cpm_uart.h index 5c76e0ae0582..7274b527a3c1 100644 --- a/drivers/serial/cpm_uart/cpm_uart.h +++ b/drivers/serial/cpm_uart/cpm_uart.h @@ -50,6 +50,15 @@ #define SCC_WAIT_CLOSING 100 +#define GPIO_CTS 0 +#define GPIO_RTS 1 +#define GPIO_DCD 2 +#define GPIO_DSR 3 +#define GPIO_DTR 4 +#define GPIO_RI 5 + +#define NUM_GPIOS (GPIO_RI+1) + struct uart_cpm_port { struct uart_port port; u16 rx_nrfifos; @@ -68,6 +77,7 @@ struct uart_cpm_port { unsigned char *rx_buf; u32 flags; void (*set_lineif)(struct uart_cpm_port *); + struct clk *clk; u8 brg; uint dp_addr; void *mem_addr; @@ -82,6 +92,7 @@ struct uart_cpm_port { int wait_closing; /* value to combine with opcode to form cpm command */ u32 command; + int gpios[NUM_GPIOS]; }; extern int cpm_uart_nr; diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c index a4f86927a74b..25efca5a7a1f 100644 --- a/drivers/serial/cpm_uart/cpm_uart_core.c +++ b/drivers/serial/cpm_uart/cpm_uart_core.c @@ -43,6 +43,9 @@ #include <linux/dma-mapping.h> #include <linux/fs_uart_pd.h> #include <linux/of_platform.h> +#include <linux/gpio.h> +#include <linux/of_gpio.h> +#include <linux/clk.h> #include <asm/io.h> #include <asm/irq.h> @@ -96,13 +99,41 @@ static unsigned int cpm_uart_tx_empty(struct uart_port *port) static void cpm_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) { - /* Whee. Do nothing. */ + struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port; + + if (pinfo->gpios[GPIO_RTS] >= 0) + gpio_set_value(pinfo->gpios[GPIO_RTS], !(mctrl & TIOCM_RTS)); + + if (pinfo->gpios[GPIO_DTR] >= 0) + gpio_set_value(pinfo->gpios[GPIO_DTR], !(mctrl & TIOCM_DTR)); } static unsigned int cpm_uart_get_mctrl(struct uart_port *port) { - /* Whee. Do nothing. */ - return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS; + struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port; + unsigned int mctrl = TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; + + if (pinfo->gpios[GPIO_CTS] >= 0) { + if (gpio_get_value(pinfo->gpios[GPIO_CTS])) + mctrl &= ~TIOCM_CTS; + } + + if (pinfo->gpios[GPIO_DSR] >= 0) { + if (gpio_get_value(pinfo->gpios[GPIO_DSR])) + mctrl &= ~TIOCM_DSR; + } + + if (pinfo->gpios[GPIO_DCD] >= 0) { + if (gpio_get_value(pinfo->gpios[GPIO_DCD])) + mctrl &= ~TIOCM_CAR; + } + + if (pinfo->gpios[GPIO_RI] >= 0) { + if (!gpio_get_value(pinfo->gpios[GPIO_RI])) + mctrl |= TIOCM_RNG; + } + + return mctrl; } /* @@ -566,7 +597,10 @@ static void cpm_uart_set_termios(struct uart_port *port, out_be16(&sccp->scc_psmr, (sbits << 12) | scval); } - cpm_set_brg(pinfo->brg - 1, baud); + if (pinfo->clk) + clk_set_rate(pinfo->clk, baud); + else + cpm_set_brg(pinfo->brg - 1, baud); spin_unlock_irqrestore(&port->lock, flags); } @@ -991,14 +1025,23 @@ static int cpm_uart_init_port(struct device_node *np, void __iomem *mem, *pram; int len; int ret; + int i; - data = of_get_property(np, "fsl,cpm-brg", &len); - if (!data || len != 4) { - printk(KERN_ERR "CPM UART %s has no/invalid " - "fsl,cpm-brg property.\n", np->name); - return -EINVAL; + data = of_get_property(np, "clock", NULL); + if (data) { + struct clk *clk = clk_get(NULL, (const char*)data); + if (!IS_ERR(clk)) + pinfo->clk = clk; + } + if (!pinfo->clk) { + data = of_get_property(np, "fsl,cpm-brg", &len); + if (!data || len != 4) { + printk(KERN_ERR "CPM UART %s has no/invalid " + "fsl,cpm-brg property.\n", np->name); + return -EINVAL; + } + pinfo->brg = *data; } - pinfo->brg = *data; data = of_get_property(np, "fsl,cpm-command", &len); if (!data || len != 4) { @@ -1050,6 +1093,9 @@ static int cpm_uart_init_port(struct device_node *np, goto out_pram; } + for (i = 0; i < NUM_GPIOS; i++) + pinfo->gpios[i] = of_get_gpio(np, i); + return cpm_uart_request_port(&pinfo->port); out_pram: diff --git a/drivers/serial/crisv10.c b/drivers/serial/crisv10.c index 8249ac490559..bf94a770bb44 100644 --- a/drivers/serial/crisv10.c +++ b/drivers/serial/crisv10.c @@ -234,7 +234,7 @@ unsigned long r_alt_ser_baudrate_shadow = 0; static struct e100_serial rs_table[] = { { .baud = DEF_BAUD, - .port = (unsigned char *)R_SERIAL0_CTRL, + .ioport = (unsigned char *)R_SERIAL0_CTRL, .irq = 1U << 12, /* uses DMA 6 and 7 */ .oclrintradr = R_DMA_CH6_CLR_INTR, .ofirstadr = R_DMA_CH6_FIRST, @@ -288,7 +288,7 @@ static struct e100_serial rs_table[] = { }, /* ttyS0 */ #ifndef CONFIG_SVINTO_SIM { .baud = DEF_BAUD, - .port = (unsigned char *)R_SERIAL1_CTRL, + .ioport = (unsigned char *)R_SERIAL1_CTRL, .irq = 1U << 16, /* uses DMA 8 and 9 */ .oclrintradr = R_DMA_CH8_CLR_INTR, .ofirstadr = R_DMA_CH8_FIRST, @@ -344,7 +344,7 @@ static struct e100_serial rs_table[] = { }, /* ttyS1 */ { .baud = DEF_BAUD, - .port = (unsigned char *)R_SERIAL2_CTRL, + .ioport = (unsigned char *)R_SERIAL2_CTRL, .irq = 1U << 4, /* uses DMA 2 and 3 */ .oclrintradr = R_DMA_CH2_CLR_INTR, .ofirstadr = R_DMA_CH2_FIRST, @@ -398,7 +398,7 @@ static struct e100_serial rs_table[] = { }, /* ttyS2 */ { .baud = DEF_BAUD, - .port = (unsigned char *)R_SERIAL3_CTRL, + .ioport = (unsigned char *)R_SERIAL3_CTRL, .irq = 1U << 8, /* uses DMA 4 and 5 */ .oclrintradr = R_DMA_CH4_CLR_INTR, .ofirstadr = R_DMA_CH4_FIRST, @@ -939,7 +939,7 @@ static const struct control_pins e100_modem_pins[NR_PORTS] = /* Output */ #define E100_RTS_GET(info) ((info)->rx_ctrl & E100_RTS_MASK) /* Input */ -#define E100_CTS_GET(info) ((info)->port[REG_STATUS] & E100_CTS_MASK) +#define E100_CTS_GET(info) ((info)->ioport[REG_STATUS] & E100_CTS_MASK) /* These are typically PA or PB and 0 means 0V, 1 means 3.3V */ /* Is an output */ @@ -1092,7 +1092,7 @@ e100_rts(struct e100_serial *info, int set) local_irq_save(flags); info->rx_ctrl &= ~E100_RTS_MASK; info->rx_ctrl |= (set ? 0 : E100_RTS_MASK); /* RTS is active low */ - info->port[REG_REC_CTRL] = info->rx_ctrl; + info->ioport[REG_REC_CTRL] = info->rx_ctrl; local_irq_restore(flags); #ifdef SERIAL_DEBUG_IO printk("ser%i rts %i\n", info->line, set); @@ -1142,7 +1142,7 @@ e100_disable_rx(struct e100_serial *info) { #ifndef CONFIG_SVINTO_SIM /* disable the receiver */ - info->port[REG_REC_CTRL] = + info->ioport[REG_REC_CTRL] = (info->rx_ctrl &= ~IO_MASK(R_SERIAL0_REC_CTRL, rec_enable)); #endif } @@ -1152,7 +1152,7 @@ e100_enable_rx(struct e100_serial *info) { #ifndef CONFIG_SVINTO_SIM /* enable the receiver */ - info->port[REG_REC_CTRL] = + info->ioport[REG_REC_CTRL] = (info->rx_ctrl |= IO_MASK(R_SERIAL0_REC_CTRL, rec_enable)); #endif } @@ -1490,7 +1490,7 @@ rs_stop(struct tty_struct *tty) xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable); } - *((unsigned long *)&info->port[REG_XOFF]) = xoff; + *((unsigned long *)&info->ioport[REG_XOFF]) = xoff; local_irq_restore(flags); } } @@ -1513,7 +1513,7 @@ rs_start(struct tty_struct *tty) xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable); } - *((unsigned long *)&info->port[REG_XOFF]) = xoff; + *((unsigned long *)&info->ioport[REG_XOFF]) = xoff; if (!info->uses_dma_out && info->xmit.head != info->xmit.tail && info->xmit.buf) e100_enable_serial_tx_ready_irq(info); @@ -1888,7 +1888,7 @@ static void receive_chars_dma(struct e100_serial *info) handle_all_descr_data(info); /* Read the status register to detect errors */ - rstat = info->port[REG_STATUS]; + rstat = info->ioport[REG_STATUS]; if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect) ) { DFLOW(DEBUG_LOG(info->line, "XOFF detect stat %x\n", rstat)); } @@ -1897,7 +1897,7 @@ static void receive_chars_dma(struct e100_serial *info) /* If we got an error, we must reset it by reading the * data_in field */ - unsigned char data = info->port[REG_DATA]; + unsigned char data = info->ioport[REG_DATA]; PROCSTAT(ser_stat[info->line].errors_cnt++); DEBUG_LOG(info->line, "#dERR: s d 0x%04X\n", @@ -2077,7 +2077,7 @@ static int force_eop_if_needed(struct e100_serial *info) /* We check data_avail bit to determine if data has * arrived since last time */ - unsigned char rstat = info->port[REG_STATUS]; + unsigned char rstat = info->ioport[REG_STATUS]; /* error or datavail? */ if (rstat & SER_ERROR_MASK) { @@ -2096,7 +2096,7 @@ static int force_eop_if_needed(struct e100_serial *info) TIMERD(DEBUG_LOG(info->line, "timeout: rstat 0x%03X\n", rstat | (info->line << 8))); /* Read data to clear status flags */ - (void)info->port[REG_DATA]; + (void)info->ioport[REG_DATA]; info->forced_eop = 0; START_FLUSH_FAST_TIMER(info, "magic"); @@ -2296,7 +2296,7 @@ struct e100_serial * handle_ser_rx_interrupt_no_dma(struct e100_serial *info) } /* Read data and status at the same time */ - data_read = *((unsigned long *)&info->port[REG_DATA_STATUS32]); + data_read = *((unsigned long *)&info->ioport[REG_DATA_STATUS32]); more_data: if (data_read & IO_MASK(R_SERIAL0_READ, xoff_detect) ) { DFLOW(DEBUG_LOG(info->line, "XOFF detect\n", 0)); @@ -2391,7 +2391,7 @@ more_data: info->icount.rx++; - data_read = *((unsigned long *)&info->port[REG_DATA_STATUS32]); + data_read = *((unsigned long *)&info->ioport[REG_DATA_STATUS32]); if (data_read & IO_MASK(R_SERIAL0_READ, data_avail)) { DEBUG_LOG(info->line, "ser_rx %c in loop\n", IO_EXTRACT(R_SERIAL0_READ, data_in, data_read)); goto more_data; @@ -2413,7 +2413,7 @@ static struct e100_serial* handle_ser_rx_interrupt(struct e100_serial *info) return handle_ser_rx_interrupt_no_dma(info); } /* DMA is used */ - rstat = info->port[REG_STATUS]; + rstat = info->ioport[REG_STATUS]; if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect) ) { DFLOW(DEBUG_LOG(info->line, "XOFF detect\n", 0)); } @@ -2426,7 +2426,7 @@ static struct e100_serial* handle_ser_rx_interrupt(struct e100_serial *info) /* If we got an error, we must reset it by reading the * data_in field */ - data = info->port[REG_DATA]; + data = info->ioport[REG_DATA]; DINTR1(DEBUG_LOG(info->line, "ser_rx! %c\n", data)); DINTR1(DEBUG_LOG(info->line, "ser_rx err stat %02X\n", rstat)); if (!data && (rstat & SER_FRAMING_ERR_MASK)) { @@ -2528,10 +2528,10 @@ static void handle_ser_tx_interrupt(struct e100_serial *info) unsigned char rstat; DFLOW(DEBUG_LOG(info->line, "tx_int: xchar 0x%02X\n", info->x_char)); local_irq_save(flags); - rstat = info->port[REG_STATUS]; + rstat = info->ioport[REG_STATUS]; DFLOW(DEBUG_LOG(info->line, "stat %x\n", rstat)); - info->port[REG_TR_DATA] = info->x_char; + info->ioport[REG_TR_DATA] = info->x_char; info->icount.tx++; info->x_char = 0; /* We must enable since it is disabled in ser_interrupt */ @@ -2545,7 +2545,7 @@ static void handle_ser_tx_interrupt(struct e100_serial *info) /* We only use normal tx interrupt when sending x_char */ DFLOW(DEBUG_LOG(info->line, "tx_int: xchar sent\n", 0)); local_irq_save(flags); - rstat = info->port[REG_STATUS]; + rstat = info->ioport[REG_STATUS]; DFLOW(DEBUG_LOG(info->line, "stat %x\n", rstat)); e100_disable_serial_tx_ready_irq(info); if (info->port.tty->stopped) @@ -2573,7 +2573,7 @@ static void handle_ser_tx_interrupt(struct e100_serial *info) DINTR2(DEBUG_LOG(info->line, "tx_int %c\n", info->xmit.buf[info->xmit.tail])); /* Send a byte, rs485 timing is critical so turn of ints */ local_irq_save(flags); - info->port[REG_TR_DATA] = info->xmit.buf[info->xmit.tail]; + info->ioport[REG_TR_DATA] = info->xmit.buf[info->xmit.tail]; info->xmit.tail = (info->xmit.tail + 1) & (SERIAL_XMIT_SIZE-1); info->icount.tx++; if (info->xmit.head == info->xmit.tail) { @@ -2848,7 +2848,7 @@ startup(struct e100_serial * info) /* dummy read to reset any serial errors */ - (void)info->port[REG_DATA]; + (void)info->ioport[REG_DATA]; /* enable the interrupts */ if (info->uses_dma_out) @@ -2897,7 +2897,7 @@ shutdown(struct e100_serial * info) /* shut down the transmitter and receiver */ DFLOW(DEBUG_LOG(info->line, "shutdown %i\n", info->line)); e100_disable_rx(info); - info->port[REG_TR_CTRL] = (info->tx_ctrl &= ~0x40); + info->ioport[REG_TR_CTRL] = (info->tx_ctrl &= ~0x40); /* disable interrupts, reset dma channels */ if (info->uses_dma_in) { @@ -2968,7 +2968,7 @@ change_speed(struct e100_serial *info) if (!info->port.tty || !info->port.tty->termios) return; - if (!info->port) + if (!info->ioport) return; cflag = info->port.tty->termios->c_cflag; @@ -3037,7 +3037,7 @@ change_speed(struct e100_serial *info) info->baud = cflag_to_baud(cflag); #ifndef CONFIG_SVINTO_SIM - info->port[REG_BAUD] = cflag_to_etrax_baud(cflag); + info->ioport[REG_BAUD] = cflag_to_etrax_baud(cflag); #endif /* CONFIG_SVINTO_SIM */ } @@ -3097,8 +3097,8 @@ change_speed(struct e100_serial *info) /* actually write the control regs to the hardware */ - info->port[REG_TR_CTRL] = info->tx_ctrl; - info->port[REG_REC_CTRL] = info->rx_ctrl; + info->ioport[REG_TR_CTRL] = info->tx_ctrl; + info->ioport[REG_REC_CTRL] = info->rx_ctrl; xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(info->port.tty)); xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable); if (info->port.tty->termios->c_iflag & IXON ) { @@ -3107,7 +3107,7 @@ change_speed(struct e100_serial *info) xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable); } - *((unsigned long *)&info->port[REG_XOFF]) = xoff; + *((unsigned long *)&info->ioport[REG_XOFF]) = xoff; local_irq_restore(flags); #endif /* !CONFIG_SVINTO_SIM */ @@ -3156,7 +3156,7 @@ static int rs_raw_write(struct tty_struct *tty, #ifdef SERIAL_DEBUG_DATA if (info->line == SERIAL_DEBUG_LINE) printk("rs_raw_write (%d), status %d\n", - count, info->port[REG_STATUS]); + count, info->ioport[REG_STATUS]); #endif #ifdef CONFIG_SVINTO_SIM @@ -3427,7 +3427,7 @@ get_serial_info(struct e100_serial * info, memset(&tmp, 0, sizeof(tmp)); tmp.type = info->type; tmp.line = info->line; - tmp.port = (int)info->port; + tmp.port = (int)info->ioport; tmp.irq = info->irq; tmp.flags = info->flags; tmp.baud_base = info->baud_base; @@ -3557,14 +3557,14 @@ char *get_control_state_str(int MLines, char *s) } #endif -static void +static int rs_break(struct tty_struct *tty, int break_state) { struct e100_serial *info = (struct e100_serial *)tty->driver_data; unsigned long flags; - if (!info->port) - return; + if (!info->ioport) + return -EIO; local_irq_save(flags); if (break_state == -1) { @@ -3575,8 +3575,9 @@ rs_break(struct tty_struct *tty, int break_state) /* Set bit 7 (txd) and 6 (tr_enable) */ info->tx_ctrl |= (0x80 | 0x40); } - info->port[REG_TR_CTRL] = info->tx_ctrl; + info->ioport[REG_TR_CTRL] = info->tx_ctrl; local_irq_restore(flags); + return 0; } static int @@ -4231,9 +4232,9 @@ static int line_info(char *buf, struct e100_serial *info) unsigned long tmp; ret = sprintf(buf, "%d: uart:E100 port:%lX irq:%d", - info->line, (unsigned long)info->port, info->irq); + info->line, (unsigned long)info->ioport, info->irq); - if (!info->port || (info->type == PORT_UNKNOWN)) { + if (!info->ioport || (info->type == PORT_UNKNOWN)) { ret += sprintf(buf+ret, "\n"); return ret; } @@ -4281,7 +4282,7 @@ static int line_info(char *buf, struct e100_serial *info) } { - unsigned char rstat = info->port[REG_STATUS]; + unsigned char rstat = info->ioport[REG_STATUS]; if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect) ) ret += sprintf(buf+ret, " xoff_detect:1"); } @@ -4502,7 +4503,7 @@ rs_init(void) if (info->enabled) { printk(KERN_INFO "%s%d at 0x%x is a builtin UART with DMA\n", - serial_driver->name, info->line, (unsigned int)info->port); + serial_driver->name, info->line, (unsigned int)info->ioport); } } #ifdef CONFIG_ETRAX_FAST_TIMER diff --git a/drivers/serial/crisv10.h b/drivers/serial/crisv10.h index ccd0f32b7372..e3c5c8c3c09b 100644 --- a/drivers/serial/crisv10.h +++ b/drivers/serial/crisv10.h @@ -36,8 +36,9 @@ struct etrax_recv_buffer { }; struct e100_serial { + struct tty_port port; int baud; - volatile u8 *port; /* R_SERIALx_CTRL */ + volatile u8 *ioport; /* R_SERIALx_CTRL */ u32 irq; /* bitnr in R_IRQ_MASK2 for dmaX_descr */ /* Output registers */ diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c index 208e42ba9455..3df2aaec829f 100644 --- a/drivers/serial/sh-sci.c +++ b/drivers/serial/sh-sci.c @@ -410,7 +410,6 @@ static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag) #endif #if defined(CONFIG_CPU_SUBTYPE_SH7760) || \ - defined(CONFIG_CPU_SUBTYPE_SH7763) || \ defined(CONFIG_CPU_SUBTYPE_SH7780) || \ defined(CONFIG_CPU_SUBTYPE_SH7785) static inline int scif_txroom(struct uart_port *port) @@ -422,6 +421,22 @@ static inline int scif_rxroom(struct uart_port *port) { return sci_in(port, SCRFDR) & 0xff; } +#elif defined(CONFIG_CPU_SUBTYPE_SH7763) +static inline int scif_txroom(struct uart_port *port) +{ + if((port->mapbase == 0xffe00000) || (port->mapbase == 0xffe08000)) /* SCIF0/1*/ + return SCIF_TXROOM_MAX - (sci_in(port, SCTFDR) & 0xff); + else /* SCIF2 */ + return SCIF2_TXROOM_MAX - (sci_in(port, SCFDR) >> 8); +} + +static inline int scif_rxroom(struct uart_port *port) +{ + if((port->mapbase == 0xffe00000) || (port->mapbase == 0xffe08000)) /* SCIF0/1*/ + return sci_in(port, SCRFDR) & 0xff; + else /* SCIF2 */ + return sci_in(port, SCFDR) & SCIF2_RFDC_MASK; +} #else static inline int scif_txroom(struct uart_port *port) { diff --git a/drivers/serial/sh-sci.h b/drivers/serial/sh-sci.h index eb84833233fd..8a0749e34ca3 100644 --- a/drivers/serial/sh-sci.h +++ b/drivers/serial/sh-sci.h @@ -123,8 +123,9 @@ #elif defined(CONFIG_CPU_SUBTYPE_SH7763) # define SCSPTR0 0xffe00024 /* 16 bit SCIF */ # define SCSPTR1 0xffe08024 /* 16 bit SCIF */ +# define SCSPTR2 0xffe10020 /* 16 bit SCIF/IRDA */ # define SCIF_ORER 0x0001 /* overrun error bit */ -# define SCSCR_INIT(port) 0x3a /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ +# define SCSCR_INIT(port) 0x38 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ # define SCIF_ONLY #elif defined(CONFIG_CPU_SUBTYPE_SH7770) # define SCSPTR0 0xff923020 /* 16 bit SCIF */ @@ -188,6 +189,7 @@ defined(CONFIG_CPU_SUBTYPE_SH7750S) || \ defined(CONFIG_CPU_SUBTYPE_SH7751) || \ defined(CONFIG_CPU_SUBTYPE_SH7751R) || \ + defined(CONFIG_CPU_SUBTYPE_SH7763) || \ defined(CONFIG_CPU_SUBTYPE_SH7780) || \ defined(CONFIG_CPU_SUBTYPE_SH7785) || \ defined(CONFIG_CPU_SUBTYPE_SHX3) @@ -225,14 +227,21 @@ #if defined(CONFIG_CPU_SUBTYPE_SH7705) || \ defined(CONFIG_CPU_SUBTYPE_SH7720) || \ defined(CONFIG_CPU_SUBTYPE_SH7721) -#define SCIF_ORER 0x0200 -#define SCIF_ERRORS ( SCIF_PER | SCIF_FER | SCIF_ER | SCIF_BRK | SCIF_ORER) -#define SCIF_RFDC_MASK 0x007f -#define SCIF_TXROOM_MAX 64 +# define SCIF_ORER 0x0200 +# define SCIF_ERRORS ( SCIF_PER | SCIF_FER | SCIF_ER | SCIF_BRK | SCIF_ORER) +# define SCIF_RFDC_MASK 0x007f +# define SCIF_TXROOM_MAX 64 +#elif defined(CONFIG_CPU_SUBTYPE_SH7763) +# define SCIF_ERRORS ( SCIF_PER | SCIF_FER | SCIF_ER | SCIF_BRK ) +# define SCIF_RFDC_MASK 0x007f +# define SCIF_TXROOM_MAX 64 +/* SH7763 SCIF2 support */ +# define SCIF2_RFDC_MASK 0x001f +# define SCIF2_TXROOM_MAX 16 #else -#define SCIF_ERRORS ( SCIF_PER | SCIF_FER | SCIF_ER | SCIF_BRK) -#define SCIF_RFDC_MASK 0x001f -#define SCIF_TXROOM_MAX 16 +# define SCIF_ERRORS ( SCIF_PER | SCIF_FER | SCIF_ER | SCIF_BRK) +# define SCIF_RFDC_MASK 0x001f +# define SCIF_TXROOM_MAX 16 #endif #if defined(SCI_ONLY) @@ -442,7 +451,6 @@ SCIx_FNS(SCxSR, 0x08, 8, 0x10, 8, 0x08, 16, 0x10, 16, 0x04, 8) SCIx_FNS(SCxRDR, 0x0a, 8, 0x14, 8, 0x0A, 8, 0x14, 8, 0x05, 8) SCIF_FNS(SCFCR, 0x0c, 8, 0x18, 16) #if defined(CONFIG_CPU_SUBTYPE_SH7760) || \ - defined(CONFIG_CPU_SUBTYPE_SH7763) || \ defined(CONFIG_CPU_SUBTYPE_SH7780) || \ defined(CONFIG_CPU_SUBTYPE_SH7785) SCIF_FNS(SCFDR, 0x0e, 16, 0x1C, 16) @@ -450,6 +458,14 @@ SCIF_FNS(SCTFDR, 0x0e, 16, 0x1C, 16) SCIF_FNS(SCRFDR, 0x0e, 16, 0x20, 16) SCIF_FNS(SCSPTR, 0, 0, 0x24, 16) SCIF_FNS(SCLSR, 0, 0, 0x28, 16) +#elif defined(CONFIG_CPU_SUBTYPE_SH7763) +SCIF_FNS(SCFDR, 0, 0, 0x1C, 16) +SCIF_FNS(SCSPTR2, 0, 0, 0x20, 16) +SCIF_FNS(SCLSR2, 0, 0, 0x24, 16) +SCIF_FNS(SCTFDR, 0x0e, 16, 0x1C, 16) +SCIF_FNS(SCRFDR, 0x0e, 16, 0x20, 16) +SCIF_FNS(SCSPTR, 0, 0, 0x24, 16) +SCIF_FNS(SCLSR, 0, 0, 0x28, 16) #else SCIF_FNS(SCFDR, 0x0e, 16, 0x1C, 16) #if defined(CONFIG_CPU_SUBTYPE_SH7722) @@ -652,6 +668,9 @@ static inline int sci_rxd_in(struct uart_port *port) return ctrl_inw(SCSPTR0) & 0x0001 ? 1 : 0; /* SCIF */ if (port->mapbase == 0xffe08000) return ctrl_inw(SCSPTR1) & 0x0001 ? 1 : 0; /* SCIF */ + if (port->mapbase == 0xffe10000) + return ctrl_inw(SCSPTR2) & 0x0001 ? 1 : 0; /* SCIF/IRDA */ + return 1; } #elif defined(CONFIG_CPU_SUBTYPE_SH7770) @@ -764,8 +783,7 @@ static inline int sci_rxd_in(struct uart_port *port) * -- Mitch Davis - 15 Jul 2000 */ -#if defined(CONFIG_CPU_SUBTYPE_SH7763) || \ - defined(CONFIG_CPU_SUBTYPE_SH7780) || \ +#if defined(CONFIG_CPU_SUBTYPE_SH7780) || \ defined(CONFIG_CPU_SUBTYPE_SH7785) #define SCBRR_VALUE(bps, clk) ((clk+16*bps)/(16*bps)-1) #elif defined(CONFIG_CPU_SUBTYPE_SH7705) || \ diff --git a/drivers/serial/v850e_uart.c b/drivers/serial/v850e_uart.c deleted file mode 100644 index 5acf061b6cd2..000000000000 --- a/drivers/serial/v850e_uart.c +++ /dev/null @@ -1,548 +0,0 @@ -/* - * drivers/serial/v850e_uart.c -- Serial I/O using V850E on-chip UART or UARTB - * - * Copyright (C) 2001,02,03 NEC Electronics Corporation - * Copyright (C) 2001,02,03 Miles Bader <miles@gnu.org> - * - * This file is subject to the terms and conditions of the GNU General - * Public License. See the file COPYING in the main directory of this - * archive for more details. - * - * Written by Miles Bader <miles@gnu.org> - */ - -/* This driver supports both the original V850E UART interface (called - merely `UART' in the docs) and the newer `UARTB' interface, which is - roughly a superset of the first one. The selection is made at - configure time -- if CONFIG_V850E_UARTB is defined, then UARTB is - presumed, otherwise the old UART -- as these are on-CPU UARTS, a system - can never have both. - - The UARTB interface also has a 16-entry FIFO mode, which is not - yet supported by this driver. */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/module.h> -#include <linux/console.h> -#include <linux/tty.h> -#include <linux/tty_flip.h> -#include <linux/serial.h> -#include <linux/serial_core.h> - -#include <asm/v850e_uart.h> - -/* Initial UART state. This may be overridden by machine-dependent headers. */ -#ifndef V850E_UART_INIT_BAUD -#define V850E_UART_INIT_BAUD 115200 -#endif -#ifndef V850E_UART_INIT_CFLAGS -#define V850E_UART_INIT_CFLAGS (B115200 | CS8 | CREAD) -#endif - -/* A string used for prefixing printed descriptions; since the same UART - macro is actually used on other chips than the V850E. This must be a - constant string. */ -#ifndef V850E_UART_CHIP_NAME -#define V850E_UART_CHIP_NAME "V850E" -#endif - -#define V850E_UART_MINOR_BASE 64 /* First tty minor number */ - - -/* Low-level UART functions. */ - -/* Configure and turn on uart channel CHAN, using the termios `control - modes' bits in CFLAGS, and a baud-rate of BAUD. */ -void v850e_uart_configure (unsigned chan, unsigned cflags, unsigned baud) -{ - int flags; - v850e_uart_speed_t old_speed; - v850e_uart_config_t old_config; - v850e_uart_speed_t new_speed = v850e_uart_calc_speed (baud); - v850e_uart_config_t new_config = v850e_uart_calc_config (cflags); - - /* Disable interrupts while we're twiddling the hardware. */ - local_irq_save (flags); - -#ifdef V850E_UART_PRE_CONFIGURE - V850E_UART_PRE_CONFIGURE (chan, cflags, baud); -#endif - - old_config = V850E_UART_CONFIG (chan); - old_speed = v850e_uart_speed (chan); - - if (! v850e_uart_speed_eq (old_speed, new_speed)) { - /* The baud rate has changed. First, disable the UART. */ - V850E_UART_CONFIG (chan) = V850E_UART_CONFIG_FINI; - old_config = 0; /* Force the uart to be re-initialized. */ - - /* Reprogram the baud-rate generator. */ - v850e_uart_set_speed (chan, new_speed); - } - - if (! (old_config & V850E_UART_CONFIG_ENABLED)) { - /* If we are using the uart for the first time, start by - enabling it, which must be done before turning on any - other bits. */ - V850E_UART_CONFIG (chan) = V850E_UART_CONFIG_INIT; - /* See the initial state. */ - old_config = V850E_UART_CONFIG (chan); - } - - if (new_config != old_config) { - /* Which of the TXE/RXE bits we'll temporarily turn off - before changing other control bits. */ - unsigned temp_disable = 0; - /* Which of the TXE/RXE bits will be enabled. */ - unsigned enable = 0; - unsigned changed_bits = new_config ^ old_config; - - /* Which of RX/TX will be enabled in the new configuration. */ - if (new_config & V850E_UART_CONFIG_RX_BITS) - enable |= (new_config & V850E_UART_CONFIG_RX_ENABLE); - if (new_config & V850E_UART_CONFIG_TX_BITS) - enable |= (new_config & V850E_UART_CONFIG_TX_ENABLE); - - /* Figure out which of RX/TX needs to be disabled; note - that this will only happen if they're not already - disabled. */ - if (changed_bits & V850E_UART_CONFIG_RX_BITS) - temp_disable - |= (old_config & V850E_UART_CONFIG_RX_ENABLE); - if (changed_bits & V850E_UART_CONFIG_TX_BITS) - temp_disable - |= (old_config & V850E_UART_CONFIG_TX_ENABLE); - - /* We have to turn off RX and/or TX mode before changing - any associated control bits. */ - if (temp_disable) - V850E_UART_CONFIG (chan) = old_config & ~temp_disable; - - /* Write the new control bits, while RX/TX are disabled. */ - if (changed_bits & ~enable) - V850E_UART_CONFIG (chan) = new_config & ~enable; - - v850e_uart_config_delay (new_config, new_speed); - - /* Write the final version, with enable bits turned on. */ - V850E_UART_CONFIG (chan) = new_config; - } - - local_irq_restore (flags); -} - - -/* Low-level console. */ - -#ifdef CONFIG_V850E_UART_CONSOLE - -static void v850e_uart_cons_write (struct console *co, - const char *s, unsigned count) -{ - if (count > 0) { - unsigned chan = co->index; - unsigned irq = V850E_UART_TX_IRQ (chan); - int irq_was_enabled, irq_was_pending, flags; - - /* We don't want to get `transmission completed' - interrupts, since we're busy-waiting, so we disable them - while sending (we don't disable interrupts entirely - because sending over a serial line is really slow). We - save the status of the tx interrupt and restore it when - we're done so that using printk doesn't interfere with - normal serial transmission (other than interleaving the - output, of course!). This should work correctly even if - this function is interrupted and the interrupt printks - something. */ - - /* Disable interrupts while fiddling with tx interrupt. */ - local_irq_save (flags); - /* Get current tx interrupt status. */ - irq_was_enabled = v850e_intc_irq_enabled (irq); - irq_was_pending = v850e_intc_irq_pending (irq); - /* Disable tx interrupt if necessary. */ - if (irq_was_enabled) - v850e_intc_disable_irq (irq); - /* Turn interrupts back on. */ - local_irq_restore (flags); - - /* Send characters. */ - while (count > 0) { - int ch = *s++; - - if (ch == '\n') { - /* We don't have the benefit of a tty - driver, so translate NL into CR LF. */ - v850e_uart_wait_for_xmit_ok (chan); - v850e_uart_putc (chan, '\r'); - } - - v850e_uart_wait_for_xmit_ok (chan); - v850e_uart_putc (chan, ch); - - count--; - } - - /* Restore saved tx interrupt status. */ - if (irq_was_enabled) { - /* Wait for the last character we sent to be - completely transmitted (as we'll get an - interrupt interrupt at that point). */ - v850e_uart_wait_for_xmit_done (chan); - /* Clear pending interrupts received due - to our transmission, unless there was already - one pending, in which case we want the - handler to be called. */ - if (! irq_was_pending) - v850e_intc_clear_pending_irq (irq); - /* ... and then turn back on handling. */ - v850e_intc_enable_irq (irq); - } - } -} - -extern struct uart_driver v850e_uart_driver; -static struct console v850e_uart_cons = -{ - .name = "ttyS", - .write = v850e_uart_cons_write, - .device = uart_console_device, - .flags = CON_PRINTBUFFER, - .cflag = V850E_UART_INIT_CFLAGS, - .index = -1, - .data = &v850e_uart_driver, -}; - -void v850e_uart_cons_init (unsigned chan) -{ - v850e_uart_configure (chan, V850E_UART_INIT_CFLAGS, - V850E_UART_INIT_BAUD); - v850e_uart_cons.index = chan; - register_console (&v850e_uart_cons); - printk ("Console: %s on-chip UART channel %d\n", - V850E_UART_CHIP_NAME, chan); -} - -/* This is what the init code actually calls. */ -static int v850e_uart_console_init (void) -{ - v850e_uart_cons_init (V850E_UART_CONSOLE_CHANNEL); - return 0; -} -console_initcall(v850e_uart_console_init); - -#define V850E_UART_CONSOLE &v850e_uart_cons - -#else /* !CONFIG_V850E_UART_CONSOLE */ -#define V850E_UART_CONSOLE 0 -#endif /* CONFIG_V850E_UART_CONSOLE */ - -/* TX/RX interrupt handlers. */ - -static void v850e_uart_stop_tx (struct uart_port *port); - -void v850e_uart_tx (struct uart_port *port) -{ - struct circ_buf *xmit = &port->info->xmit; - int stopped = uart_tx_stopped (port); - - if (v850e_uart_xmit_ok (port->line)) { - int tx_ch; - - if (port->x_char) { - tx_ch = port->x_char; - port->x_char = 0; - } else if (!uart_circ_empty (xmit) && !stopped) { - tx_ch = xmit->buf[xmit->tail]; - xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); - } else - goto no_xmit; - - v850e_uart_putc (port->line, tx_ch); - port->icount.tx++; - - if (uart_circ_chars_pending (xmit) < WAKEUP_CHARS) - uart_write_wakeup (port); - } - - no_xmit: - if (uart_circ_empty (xmit) || stopped) - v850e_uart_stop_tx (port, stopped); -} - -static irqreturn_t v850e_uart_tx_irq(int irq, void *data) -{ - struct uart_port *port = data; - v850e_uart_tx (port); - return IRQ_HANDLED; -} - -static irqreturn_t v850e_uart_rx_irq(int irq, void *data) -{ - struct uart_port *port = data; - unsigned ch_stat = TTY_NORMAL; - unsigned ch = v850e_uart_getc (port->line); - unsigned err = v850e_uart_err (port->line); - - if (err) { - if (err & V850E_UART_ERR_OVERRUN) { - ch_stat = TTY_OVERRUN; - port->icount.overrun++; - } else if (err & V850E_UART_ERR_FRAME) { - ch_stat = TTY_FRAME; - port->icount.frame++; - } else if (err & V850E_UART_ERR_PARITY) { - ch_stat = TTY_PARITY; - port->icount.parity++; - } - } - - port->icount.rx++; - - tty_insert_flip_char (port->info->port.tty, ch, ch_stat); - tty_schedule_flip (port->info->port.tty); - - return IRQ_HANDLED; -} - - -/* Control functions for the serial framework. */ - -static void v850e_uart_nop (struct uart_port *port) { } -static int v850e_uart_success (struct uart_port *port) { return 0; } - -static unsigned v850e_uart_tx_empty (struct uart_port *port) -{ - return TIOCSER_TEMT; /* Can't detect. */ -} - -static void v850e_uart_set_mctrl (struct uart_port *port, unsigned mctrl) -{ -#ifdef V850E_UART_SET_RTS - V850E_UART_SET_RTS (port->line, (mctrl & TIOCM_RTS)); -#endif -} - -static unsigned v850e_uart_get_mctrl (struct uart_port *port) -{ - /* We don't support DCD or DSR, so consider them permanently active. */ - int mctrl = TIOCM_CAR | TIOCM_DSR; - - /* We may support CTS. */ -#ifdef V850E_UART_CTS - mctrl |= V850E_UART_CTS(port->line) ? TIOCM_CTS : 0; -#else - mctrl |= TIOCM_CTS; -#endif - - return mctrl; -} - -static void v850e_uart_start_tx (struct uart_port *port) -{ - v850e_intc_disable_irq (V850E_UART_TX_IRQ (port->line)); - v850e_uart_tx (port); - v850e_intc_enable_irq (V850E_UART_TX_IRQ (port->line)); -} - -static void v850e_uart_stop_tx (struct uart_port *port) -{ - v850e_intc_disable_irq (V850E_UART_TX_IRQ (port->line)); -} - -static void v850e_uart_start_rx (struct uart_port *port) -{ - v850e_intc_enable_irq (V850E_UART_RX_IRQ (port->line)); -} - -static void v850e_uart_stop_rx (struct uart_port *port) -{ - v850e_intc_disable_irq (V850E_UART_RX_IRQ (port->line)); -} - -static void v850e_uart_break_ctl (struct uart_port *port, int break_ctl) -{ - /* Umm, do this later. */ -} - -static int v850e_uart_startup (struct uart_port *port) -{ - int err; - - /* Alloc RX irq. */ - err = request_irq (V850E_UART_RX_IRQ (port->line), v850e_uart_rx_irq, - IRQF_DISABLED, "v850e_uart", port); - if (err) - return err; - - /* Alloc TX irq. */ - err = request_irq (V850E_UART_TX_IRQ (port->line), v850e_uart_tx_irq, - IRQF_DISABLED, "v850e_uart", port); - if (err) { - free_irq (V850E_UART_RX_IRQ (port->line), port); - return err; - } - - v850e_uart_start_rx (port); - - return 0; -} - -static void v850e_uart_shutdown (struct uart_port *port) -{ - /* Disable port interrupts. */ - free_irq (V850E_UART_TX_IRQ (port->line), port); - free_irq (V850E_UART_RX_IRQ (port->line), port); - - /* Turn off xmit/recv enable bits. */ - V850E_UART_CONFIG (port->line) - &= ~(V850E_UART_CONFIG_TX_ENABLE - | V850E_UART_CONFIG_RX_ENABLE); - /* Then reset the channel. */ - V850E_UART_CONFIG (port->line) = 0; -} - -static void -v850e_uart_set_termios (struct uart_port *port, struct ktermios *termios, - struct ktermios *old) -{ - unsigned cflags = termios->c_cflag; - - /* Restrict flags to legal values. */ - if ((cflags & CSIZE) != CS7 && (cflags & CSIZE) != CS8) - /* The new value of CSIZE is invalid, use the old value. */ - cflags = (cflags & ~CSIZE) - | (old ? (old->c_cflag & CSIZE) : CS8); - - termios->c_cflag = cflags; - - v850e_uart_configure (port->line, cflags, - uart_get_baud_rate (port, termios, old, - v850e_uart_min_baud(), - v850e_uart_max_baud())); -} - -static const char *v850e_uart_type (struct uart_port *port) -{ - return port->type == PORT_V850E_UART ? "v850e_uart" : 0; -} - -static void v850e_uart_config_port (struct uart_port *port, int flags) -{ - if (flags & UART_CONFIG_TYPE) - port->type = PORT_V850E_UART; -} - -static int -v850e_uart_verify_port (struct uart_port *port, struct serial_struct *ser) -{ - if (ser->type != PORT_UNKNOWN && ser->type != PORT_V850E_UART) - return -EINVAL; - if (ser->irq != V850E_UART_TX_IRQ (port->line)) - return -EINVAL; - return 0; -} - -static struct uart_ops v850e_uart_ops = { - .tx_empty = v850e_uart_tx_empty, - .get_mctrl = v850e_uart_get_mctrl, - .set_mctrl = v850e_uart_set_mctrl, - .start_tx = v850e_uart_start_tx, - .stop_tx = v850e_uart_stop_tx, - .stop_rx = v850e_uart_stop_rx, - .enable_ms = v850e_uart_nop, - .break_ctl = v850e_uart_break_ctl, - .startup = v850e_uart_startup, - .shutdown = v850e_uart_shutdown, - .set_termios = v850e_uart_set_termios, - .type = v850e_uart_type, - .release_port = v850e_uart_nop, - .request_port = v850e_uart_success, - .config_port = v850e_uart_config_port, - .verify_port = v850e_uart_verify_port, -}; - -/* Initialization and cleanup. */ - -static struct uart_driver v850e_uart_driver = { - .owner = THIS_MODULE, - .driver_name = "v850e_uart", - .dev_name = "ttyS", - .major = TTY_MAJOR, - .minor = V850E_UART_MINOR_BASE, - .nr = V850E_UART_NUM_CHANNELS, - .cons = V850E_UART_CONSOLE, -}; - - -static struct uart_port v850e_uart_ports[V850E_UART_NUM_CHANNELS]; - -static int __init v850e_uart_init (void) -{ - int rval; - - printk (KERN_INFO "%s on-chip UART\n", V850E_UART_CHIP_NAME); - - rval = uart_register_driver (&v850e_uart_driver); - if (rval == 0) { - unsigned chan; - - for (chan = 0; chan < V850E_UART_NUM_CHANNELS; chan++) { - struct uart_port *port = &v850e_uart_ports[chan]; - - memset (port, 0, sizeof *port); - - port->ops = &v850e_uart_ops; - port->line = chan; - port->iotype = UPIO_MEM; - port->flags = UPF_BOOT_AUTOCONF; - - /* We actually use multiple IRQs, but the serial - framework seems to mainly use this for - informational purposes anyway. Here we use the TX - irq. */ - port->irq = V850E_UART_TX_IRQ (chan); - - /* The serial framework doesn't really use these - membase/mapbase fields for anything useful, but - it requires that they be something non-zero to - consider the port `valid', and also uses them - for informational purposes. */ - port->membase = (void *)V850E_UART_BASE_ADDR (chan); - port->mapbase = V850E_UART_BASE_ADDR (chan); - - /* The framework insists on knowing the uart's master - clock freq, though it doesn't seem to do anything - useful for us with it. We must make it at least - higher than (the maximum baud rate * 16), otherwise - the framework will puke during its internal - calculations, and force the baud rate to be 9600. - To be accurate though, just repeat the calculation - we use when actually setting the speed. */ - port->uartclk = v850e_uart_max_clock() * 16; - - uart_add_one_port (&v850e_uart_driver, port); - } - } - - return rval; -} - -static void __exit v850e_uart_exit (void) -{ - unsigned chan; - - for (chan = 0; chan < V850E_UART_NUM_CHANNELS; chan++) - uart_remove_one_port (&v850e_uart_driver, - &v850e_uart_ports[chan]); - - uart_unregister_driver (&v850e_uart_driver); -} - -module_init (v850e_uart_init); -module_exit (v850e_uart_exit); - -MODULE_AUTHOR ("Miles Bader"); -MODULE_DESCRIPTION ("NEC " V850E_UART_CHIP_NAME " on-chip UART"); -MODULE_LICENSE ("GPL"); |
