diff options
Diffstat (limited to 'drivers/net/wireless/intersil/orinoco/hermes.h')
| -rw-r--r-- | drivers/net/wireless/intersil/orinoco/hermes.h | 520 |
1 files changed, 520 insertions, 0 deletions
diff --git a/drivers/net/wireless/intersil/orinoco/hermes.h b/drivers/net/wireless/intersil/orinoco/hermes.h new file mode 100644 index 000000000000..28a42448d329 --- /dev/null +++ b/drivers/net/wireless/intersil/orinoco/hermes.h @@ -0,0 +1,520 @@ +/* hermes.h + * + * Driver core for the "Hermes" wireless MAC controller, as used in + * the Lucent Orinoco and Cabletron RoamAbout cards. It should also + * work on the hfa3841 and hfa3842 MAC controller chips used in the + * Prism I & II chipsets. + * + * This is not a complete driver, just low-level access routines for + * the MAC controller itself. + * + * Based on the prism2 driver from Absolute Value Systems' linux-wlan + * project, the Linux wvlan_cs driver, Lucent's HCF-Light + * (wvlan_hcf.c) library, and the NetBSD wireless driver. + * + * Copyright (C) 2000, David Gibson, Linuxcare Australia. + * (C) Copyright David Gibson, IBM Corp. 2001-2003. + * + * Portions taken from hfa384x.h. + * Copyright (C) 1999 AbsoluteValue Systems, Inc. All Rights Reserved. + * + * This file distributed under the GPL, version 2. + */ + +#ifndef _HERMES_H +#define _HERMES_H + +/* Notes on locking: + * + * As a module of low level hardware access routines, there is no + * locking. Users of this module should ensure that they serialize + * access to the hermes structure, and to the hardware +*/ + +#include <linux/if_ether.h> +#include <linux/io.h> + +/* + * Limits and constants + */ +#define HERMES_ALLOC_LEN_MIN (4) +#define HERMES_ALLOC_LEN_MAX (2400) +#define HERMES_LTV_LEN_MAX (34) +#define HERMES_BAP_DATALEN_MAX (4096) +#define HERMES_BAP_OFFSET_MAX (4096) +#define HERMES_PORTID_MAX (7) +#define HERMES_NUMPORTS_MAX (HERMES_PORTID_MAX + 1) +#define HERMES_PDR_LEN_MAX (260) /* in bytes, from EK */ +#define HERMES_PDA_RECS_MAX (200) /* a guess */ +#define HERMES_PDA_LEN_MAX (1024) /* in bytes, from EK */ +#define HERMES_SCANRESULT_MAX (35) +#define HERMES_CHINFORESULT_MAX (8) +#define HERMES_MAX_MULTICAST (16) +#define HERMES_MAGIC (0x7d1f) + +/* + * Hermes register offsets + */ +#define HERMES_CMD (0x00) +#define HERMES_PARAM0 (0x02) +#define HERMES_PARAM1 (0x04) +#define HERMES_PARAM2 (0x06) +#define HERMES_STATUS (0x08) +#define HERMES_RESP0 (0x0A) +#define HERMES_RESP1 (0x0C) +#define HERMES_RESP2 (0x0E) +#define HERMES_INFOFID (0x10) +#define HERMES_RXFID (0x20) +#define HERMES_ALLOCFID (0x22) +#define HERMES_TXCOMPLFID (0x24) +#define HERMES_SELECT0 (0x18) +#define HERMES_OFFSET0 (0x1C) +#define HERMES_DATA0 (0x36) +#define HERMES_SELECT1 (0x1A) +#define HERMES_OFFSET1 (0x1E) +#define HERMES_DATA1 (0x38) +#define HERMES_EVSTAT (0x30) +#define HERMES_INTEN (0x32) +#define HERMES_EVACK (0x34) +#define HERMES_CONTROL (0x14) +#define HERMES_SWSUPPORT0 (0x28) +#define HERMES_SWSUPPORT1 (0x2A) +#define HERMES_SWSUPPORT2 (0x2C) +#define HERMES_AUXPAGE (0x3A) +#define HERMES_AUXOFFSET (0x3C) +#define HERMES_AUXDATA (0x3E) + +/* + * CMD register bitmasks + */ +#define HERMES_CMD_BUSY (0x8000) +#define HERMES_CMD_AINFO (0x7f00) +#define HERMES_CMD_MACPORT (0x0700) +#define HERMES_CMD_RECL (0x0100) +#define HERMES_CMD_WRITE (0x0100) +#define HERMES_CMD_PROGMODE (0x0300) +#define HERMES_CMD_CMDCODE (0x003f) + +/* + * STATUS register bitmasks + */ +#define HERMES_STATUS_RESULT (0x7f00) +#define HERMES_STATUS_CMDCODE (0x003f) + +/* + * OFFSET register bitmasks + */ +#define HERMES_OFFSET_BUSY (0x8000) +#define HERMES_OFFSET_ERR (0x4000) +#define HERMES_OFFSET_DATAOFF (0x0ffe) + +/* + * Event register bitmasks (INTEN, EVSTAT, EVACK) + */ +#define HERMES_EV_TICK (0x8000) +#define HERMES_EV_WTERR (0x4000) +#define HERMES_EV_INFDROP (0x2000) +#define HERMES_EV_INFO (0x0080) +#define HERMES_EV_DTIM (0x0020) +#define HERMES_EV_CMD (0x0010) +#define HERMES_EV_ALLOC (0x0008) +#define HERMES_EV_TXEXC (0x0004) +#define HERMES_EV_TX (0x0002) +#define HERMES_EV_RX (0x0001) + +/* + * Command codes + */ +/*--- Controller Commands ----------------------------*/ +#define HERMES_CMD_INIT (0x0000) +#define HERMES_CMD_ENABLE (0x0001) +#define HERMES_CMD_DISABLE (0x0002) +#define HERMES_CMD_DIAG (0x0003) + +/*--- Buffer Mgmt Commands ---------------------------*/ +#define HERMES_CMD_ALLOC (0x000A) +#define HERMES_CMD_TX (0x000B) + +/*--- Regulate Commands ------------------------------*/ +#define HERMES_CMD_NOTIFY (0x0010) +#define HERMES_CMD_INQUIRE (0x0011) + +/*--- Configure Commands -----------------------------*/ +#define HERMES_CMD_ACCESS (0x0021) +#define HERMES_CMD_DOWNLD (0x0022) + +/*--- Serial I/O Commands ----------------------------*/ +#define HERMES_CMD_READMIF (0x0030) +#define HERMES_CMD_WRITEMIF (0x0031) + +/*--- Debugging Commands -----------------------------*/ +#define HERMES_CMD_TEST (0x0038) + + +/* Test command arguments */ +#define HERMES_TEST_SET_CHANNEL 0x0800 +#define HERMES_TEST_MONITOR 0x0b00 +#define HERMES_TEST_STOP 0x0f00 + +/* Authentication algorithms */ +#define HERMES_AUTH_OPEN 1 +#define HERMES_AUTH_SHARED_KEY 2 + +/* WEP settings */ +#define HERMES_WEP_PRIVACY_INVOKED 0x0001 +#define HERMES_WEP_EXCL_UNENCRYPTED 0x0002 +#define HERMES_WEP_HOST_ENCRYPT 0x0010 +#define HERMES_WEP_HOST_DECRYPT 0x0080 + +/* Symbol hostscan options */ +#define HERMES_HOSTSCAN_SYMBOL_5SEC 0x0001 +#define HERMES_HOSTSCAN_SYMBOL_ONCE 0x0002 +#define HERMES_HOSTSCAN_SYMBOL_PASSIVE 0x0040 +#define HERMES_HOSTSCAN_SYMBOL_BCAST 0x0080 + +/* + * Frame structures and constants + */ + +#define HERMES_DESCRIPTOR_OFFSET 0 +#define HERMES_802_11_OFFSET (14) +#define HERMES_802_3_OFFSET (14 + 32) +#define HERMES_802_2_OFFSET (14 + 32 + 14) +#define HERMES_TXCNTL2_OFFSET (HERMES_802_3_OFFSET - 2) + +#define HERMES_RXSTAT_ERR (0x0003) +#define HERMES_RXSTAT_BADCRC (0x0001) +#define HERMES_RXSTAT_UNDECRYPTABLE (0x0002) +#define HERMES_RXSTAT_MIC (0x0010) /* Frame contains MIC */ +#define HERMES_RXSTAT_MACPORT (0x0700) +#define HERMES_RXSTAT_PCF (0x1000) /* Frame was received in CF period */ +#define HERMES_RXSTAT_MIC_KEY_ID (0x1800) /* MIC key used */ +#define HERMES_RXSTAT_MSGTYPE (0xE000) +#define HERMES_RXSTAT_1042 (0x2000) /* RFC-1042 frame */ +#define HERMES_RXSTAT_TUNNEL (0x4000) /* bridge-tunnel encoded frame */ +#define HERMES_RXSTAT_WMP (0x6000) /* Wavelan-II Management Protocol frame */ + +/* Shift amount for key ID in RXSTAT and TXCTRL */ +#define HERMES_MIC_KEY_ID_SHIFT 11 + +struct hermes_tx_descriptor { + __le16 status; + __le16 reserved1; + __le16 reserved2; + __le32 sw_support; + u8 retry_count; + u8 tx_rate; + __le16 tx_control; +} __packed; + +#define HERMES_TXSTAT_RETRYERR (0x0001) +#define HERMES_TXSTAT_AGEDERR (0x0002) +#define HERMES_TXSTAT_DISCON (0x0004) +#define HERMES_TXSTAT_FORMERR (0x0008) + +#define HERMES_TXCTRL_TX_OK (0x0002) /* ?? interrupt on Tx complete */ +#define HERMES_TXCTRL_TX_EX (0x0004) /* ?? interrupt on Tx exception */ +#define HERMES_TXCTRL_802_11 (0x0008) /* We supply 802.11 header */ +#define HERMES_TXCTRL_MIC (0x0010) /* 802.3 + TKIP */ +#define HERMES_TXCTRL_MIC_KEY_ID (0x1800) /* MIC Key ID mask */ +#define HERMES_TXCTRL_ALT_RTRY (0x0020) + +/* Inquiry constants and data types */ + +#define HERMES_INQ_TALLIES (0xF100) +#define HERMES_INQ_SCAN (0xF101) +#define HERMES_INQ_CHANNELINFO (0xF102) +#define HERMES_INQ_HOSTSCAN (0xF103) +#define HERMES_INQ_HOSTSCAN_SYMBOL (0xF104) +#define HERMES_INQ_LINKSTATUS (0xF200) +#define HERMES_INQ_SEC_STAT_AGERE (0xF202) + +struct hermes_tallies_frame { + __le16 TxUnicastFrames; + __le16 TxMulticastFrames; + __le16 TxFragments; + __le16 TxUnicastOctets; + __le16 TxMulticastOctets; + __le16 TxDeferredTransmissions; + __le16 TxSingleRetryFrames; + __le16 TxMultipleRetryFrames; + __le16 TxRetryLimitExceeded; + __le16 TxDiscards; + __le16 RxUnicastFrames; + __le16 RxMulticastFrames; + __le16 RxFragments; + __le16 RxUnicastOctets; + __le16 RxMulticastOctets; + __le16 RxFCSErrors; + __le16 RxDiscards_NoBuffer; + __le16 TxDiscardsWrongSA; + __le16 RxWEPUndecryptable; + __le16 RxMsgInMsgFragments; + __le16 RxMsgInBadMsgFragments; + /* Those last are probably not available in very old firmwares */ + __le16 RxDiscards_WEPICVError; + __le16 RxDiscards_WEPExcluded; +} __packed; + +/* Grabbed from wlan-ng - Thanks Mark... - Jean II + * This is the result of a scan inquiry command */ +/* Structure describing info about an Access Point */ +struct prism2_scan_apinfo { + __le16 channel; /* Channel where the AP sits */ + __le16 noise; /* Noise level */ + __le16 level; /* Signal level */ + u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ + __le16 beacon_interv; /* Beacon interval */ + __le16 capabilities; /* Capabilities */ + __le16 essid_len; /* ESSID length */ + u8 essid[32]; /* ESSID of the network */ + u8 rates[10]; /* Bit rate supported */ + __le16 proberesp_rate; /* Data rate of the response frame */ + __le16 atim; /* ATIM window time, Kus (hostscan only) */ +} __packed; + +/* Same stuff for the Lucent/Agere card. + * Thanks to h1kari <h1kari AT dachb0den.com> - Jean II */ +struct agere_scan_apinfo { + __le16 channel; /* Channel where the AP sits */ + __le16 noise; /* Noise level */ + __le16 level; /* Signal level */ + u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ + __le16 beacon_interv; /* Beacon interval */ + __le16 capabilities; /* Capabilities */ + /* bits: 0-ess, 1-ibss, 4-privacy [wep] */ + __le16 essid_len; /* ESSID length */ + u8 essid[32]; /* ESSID of the network */ +} __packed; + +/* Moustafa: Scan structure for Symbol cards */ +struct symbol_scan_apinfo { + u8 channel; /* Channel where the AP sits */ + u8 unknown1; /* 8 in 2.9x and 3.9x f/w, 0 otherwise */ + __le16 noise; /* Noise level */ + __le16 level; /* Signal level */ + u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ + __le16 beacon_interv; /* Beacon interval */ + __le16 capabilities; /* Capabilities */ + /* bits: 0-ess, 1-ibss, 4-privacy [wep] */ + __le16 essid_len; /* ESSID length */ + u8 essid[32]; /* ESSID of the network */ + __le16 rates[5]; /* Bit rate supported */ + __le16 basic_rates; /* Basic rates bitmask */ + u8 unknown2[6]; /* Always FF:FF:FF:FF:00:00 */ + u8 unknown3[8]; /* Always 0, appeared in f/w 3.91-68 */ +} __packed; + +union hermes_scan_info { + struct agere_scan_apinfo a; + struct prism2_scan_apinfo p; + struct symbol_scan_apinfo s; +}; + +/* Extended scan struct for HERMES_INQ_CHANNELINFO. + * wl_lkm calls this an ACS scan (Automatic Channel Select). + * Keep out of union hermes_scan_info because it is much bigger than + * the older scan structures. */ +struct agere_ext_scan_info { + __le16 reserved0; + + u8 noise; + u8 level; + u8 rx_flow; + u8 rate; + __le16 reserved1[2]; + + __le16 frame_control; + __le16 dur_id; + u8 addr1[ETH_ALEN]; + u8 addr2[ETH_ALEN]; + u8 bssid[ETH_ALEN]; + __le16 sequence; + u8 addr4[ETH_ALEN]; + + __le16 data_length; + + /* Next 3 fields do not get filled in. */ + u8 daddr[ETH_ALEN]; + u8 saddr[ETH_ALEN]; + __le16 len_type; + + __le64 timestamp; + __le16 beacon_interval; + __le16 capabilities; + u8 data[0]; +} __packed; + +#define HERMES_LINKSTATUS_NOT_CONNECTED (0x0000) +#define HERMES_LINKSTATUS_CONNECTED (0x0001) +#define HERMES_LINKSTATUS_DISCONNECTED (0x0002) +#define HERMES_LINKSTATUS_AP_CHANGE (0x0003) +#define HERMES_LINKSTATUS_AP_OUT_OF_RANGE (0x0004) +#define HERMES_LINKSTATUS_AP_IN_RANGE (0x0005) +#define HERMES_LINKSTATUS_ASSOC_FAILED (0x0006) + +struct hermes_linkstatus { + __le16 linkstatus; /* Link status */ +} __packed; + +struct hermes_response { + u16 status, resp0, resp1, resp2; +}; + +/* "ID" structure - used for ESSID and station nickname */ +struct hermes_idstring { + __le16 len; + __le16 val[16]; +} __packed; + +struct hermes_multicast { + u8 addr[HERMES_MAX_MULTICAST][ETH_ALEN]; +} __packed; + +/* Timeouts */ +#define HERMES_BAP_BUSY_TIMEOUT (10000) /* In iterations of ~1us */ + +struct hermes; + +/* Functions to access hardware */ +struct hermes_ops { + int (*init)(struct hermes *hw); + int (*cmd_wait)(struct hermes *hw, u16 cmd, u16 parm0, + struct hermes_response *resp); + int (*init_cmd_wait)(struct hermes *hw, u16 cmd, + u16 parm0, u16 parm1, u16 parm2, + struct hermes_response *resp); + int (*allocate)(struct hermes *hw, u16 size, u16 *fid); + int (*read_ltv)(struct hermes *hw, int bap, u16 rid, unsigned buflen, + u16 *length, void *buf); + int (*write_ltv)(struct hermes *hw, int bap, u16 rid, + u16 length, const void *value); + int (*bap_pread)(struct hermes *hw, int bap, void *buf, int len, + u16 id, u16 offset); + int (*bap_pwrite)(struct hermes *hw, int bap, const void *buf, + int len, u16 id, u16 offset); + int (*read_pda)(struct hermes *hw, __le16 *pda, + u32 pda_addr, u16 pda_len); + int (*program_init)(struct hermes *hw, u32 entry_point); + int (*program_end)(struct hermes *hw); + int (*program)(struct hermes *hw, const char *buf, + u32 addr, u32 len); + void (*lock_irqsave)(spinlock_t *lock, unsigned long *flags); + void (*unlock_irqrestore)(spinlock_t *lock, unsigned long *flags); + void (*lock_irq)(spinlock_t *lock); + void (*unlock_irq)(spinlock_t *lock); +}; + +/* Basic control structure */ +struct hermes { + void __iomem *iobase; + int reg_spacing; +#define HERMES_16BIT_REGSPACING 0 +#define HERMES_32BIT_REGSPACING 1 + u16 inten; /* Which interrupts should be enabled? */ + bool eeprom_pda; + const struct hermes_ops *ops; + void *priv; +}; + +/* Register access convenience macros */ +#define hermes_read_reg(hw, off) \ + (ioread16((hw)->iobase + ((off) << (hw)->reg_spacing))) +#define hermes_write_reg(hw, off, val) \ + (iowrite16((val), (hw)->iobase + ((off) << (hw)->reg_spacing))) +#define hermes_read_regn(hw, name) hermes_read_reg((hw), HERMES_##name) +#define hermes_write_regn(hw, name, val) \ + hermes_write_reg((hw), HERMES_##name, (val)) + +/* Function prototypes */ +void hermes_struct_init(struct hermes *hw, void __iomem *address, + int reg_spacing); + +/* Inline functions */ + +static inline int hermes_present(struct hermes *hw) +{ + return hermes_read_regn(hw, SWSUPPORT0) == HERMES_MAGIC; +} + +static inline void hermes_set_irqmask(struct hermes *hw, u16 events) +{ + hw->inten = events; + hermes_write_regn(hw, INTEN, events); +} + +static inline int hermes_enable_port(struct hermes *hw, int port) +{ + return hw->ops->cmd_wait(hw, HERMES_CMD_ENABLE | (port << 8), + 0, NULL); +} + +static inline int hermes_disable_port(struct hermes *hw, int port) +{ + return hw->ops->cmd_wait(hw, HERMES_CMD_DISABLE | (port << 8), + 0, NULL); +} + +/* Initiate an INQUIRE command (tallies or scan). The result will come as an + * information frame in __orinoco_ev_info() */ +static inline int hermes_inquire(struct hermes *hw, u16 rid) +{ + return hw->ops->cmd_wait(hw, HERMES_CMD_INQUIRE, rid, NULL); +} + +#define HERMES_BYTES_TO_RECLEN(n) ((((n) + 1) / 2) + 1) +#define HERMES_RECLEN_TO_BYTES(n) (((n) - 1) * 2) + +/* Note that for the next two, the count is in 16-bit words, not bytes */ +static inline void hermes_read_words(struct hermes *hw, int off, + void *buf, unsigned count) +{ + off = off << hw->reg_spacing; + ioread16_rep(hw->iobase + off, buf, count); +} + +static inline void hermes_write_bytes(struct hermes *hw, int off, + const char *buf, unsigned count) +{ + off = off << hw->reg_spacing; + iowrite16_rep(hw->iobase + off, buf, count >> 1); + if (unlikely(count & 1)) + iowrite8(buf[count - 1], hw->iobase + off); +} + +static inline void hermes_clear_words(struct hermes *hw, int off, + unsigned count) +{ + unsigned i; + + off = off << hw->reg_spacing; + + for (i = 0; i < count; i++) + iowrite16(0, hw->iobase + off); +} + +#define HERMES_READ_RECORD(hw, bap, rid, buf) \ + (hw->ops->read_ltv((hw), (bap), (rid), sizeof(*buf), NULL, (buf))) +#define HERMES_WRITE_RECORD(hw, bap, rid, buf) \ + (hw->ops->write_ltv((hw), (bap), (rid), \ + HERMES_BYTES_TO_RECLEN(sizeof(*buf)), (buf))) + +static inline int hermes_read_wordrec(struct hermes *hw, int bap, u16 rid, + u16 *word) +{ + __le16 rec; + int err; + + err = HERMES_READ_RECORD(hw, bap, rid, &rec); + *word = le16_to_cpu(rec); + return err; +} + +static inline int hermes_write_wordrec(struct hermes *hw, int bap, u16 rid, + u16 word) +{ + __le16 rec = cpu_to_le16(word); + return HERMES_WRITE_RECORD(hw, bap, rid, &rec); +} + +#endif /* _HERMES_H */ |
