diff options
Diffstat (limited to 'arch')
50 files changed, 4413 insertions, 139 deletions
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms index ca196d8e76f2..bb2616b16157 100644 --- a/arch/arm64/Kconfig.platforms +++ b/arch/arm64/Kconfig.platforms @@ -140,6 +140,12 @@ config ARCH_R8A7795 help This enables support for the Renesas R-Car H3 SoC. +config ARCH_R8A7796 + bool "Renesas R-Car M3-W SoC Platform" + depends on ARCH_RENESAS + help + This enables support for the Renesas R-Car M3-W SoC. + config ARCH_STRATIX10 bool "Altera's Stratix 10 SoCFPGA Family" help diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts index 7f2c6747a71e..90a84c514d3d 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts @@ -45,6 +45,7 @@ /dts-v1/; #include "meson-gxbb.dtsi" +#include <dt-bindings/gpio/gpio.h> / { compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb"; @@ -62,8 +63,27 @@ device_type = "memory"; reg = <0x0 0x0 0x0 0x80000000>; }; + + leds { + compatible = "gpio-leds"; + blue { + label = "c2:blue:alive"; + gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + }; }; &uart_AO { status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +ðmac { + status = "okay"; + pinctrl-0 = <ð_pins>; + pinctrl-names = "default"; }; + diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi index bf7ff1d41851..f4f30f674b4c 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi @@ -62,4 +62,13 @@ /* This UART is brought out to the DB9 connector */ &uart_AO { status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; }; + +ðmac { + status = "okay"; + pinctrl-0 = <ð_pins>; + pinctrl-names = "default"; +}; + diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi index 012cdccc8a35..54bb7c739089 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi @@ -56,4 +56,7 @@ &uart_AO { status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; + }; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi index 832815d80462..e502c24b0ac7 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi @@ -43,6 +43,8 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/gpio/meson-gxbb-gpio.h> +#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h> / { compatible = "amlogic,meson-gxbb"; @@ -129,13 +131,35 @@ #size-cells = <2>; ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>; + reset: reset-controller@4404 { + compatible = "amlogic,meson-gxbb-reset"; + reg = <0x0 0x04404 0x0 0x20>; + #reset-cells = <1>; + }; + uart_A: serial@84c0 { compatible = "amlogic,meson-uart"; - reg = <0x0 0x084c0 0x0 0x14>; + reg = <0x0 0x84c0 0x0 0x14>; interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>; clocks = <&xtal>; status = "disabled"; }; + + uart_B: serial@84dc { + compatible = "amlogic,meson-uart"; + reg = <0x0 0x84dc 0x0 0x14>; + interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>; + clocks = <&xtal>; + status = "disabled"; + }; + + uart_C: serial@8700 { + compatible = "amlogic,meson-uart"; + reg = <0x0 0x8700 0x0 0x14>; + interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>; + clocks = <&xtal>; + status = "disabled"; + }; }; gic: interrupt-controller@c4301000 { @@ -158,6 +182,29 @@ #size-cells = <2>; ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>; + pinctrl_aobus: pinctrl@14 { + compatible = "amlogic,meson-gxbb-aobus-pinctrl"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + gpio_ao: bank@14 { + reg = <0x0 0x00014 0x0 0x8>, + <0x0 0x0002c 0x0 0x4>, + <0x0 0x00024 0x0 0x8>; + reg-names = "mux", "pull", "gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + uart_ao_a_pins: uart_ao_a { + mux { + groups = "uart_tx_ao_a", "uart_rx_ao_a"; + function = "uart_ao"; + }; + }; + }; + uart_AO: serial@4c0 { compatible = "amlogic,meson-uart"; reg = <0x0 0x004c0 0x0 0x14>; @@ -167,6 +214,115 @@ }; }; + periphs: periphs@c8834000 { + compatible = "simple-bus"; + reg = <0x0 0xc8834000 0x0 0x2000>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0x0 0x0 0x0 0xc8834000 0x0 0x2000>; + + rng { + compatible = "amlogic,meson-rng"; + reg = <0x0 0x0 0x0 0x4>; + }; + + pinctrl_periphs: pinctrl@4b0 { + compatible = "amlogic,meson-gxbb-periphs-pinctrl"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + gpio: bank@4b0 { + reg = <0x0 0x004b0 0x0 0x28>, + <0x0 0x004e8 0x0 0x14>, + <0x0 0x00120 0x0 0x14>, + <0x0 0x00430 0x0 0x40>; + reg-names = "mux", "pull", "pull-enable", "gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + emmc_pins: emmc { + mux { + groups = "emmc_nand_d07", + "emmc_cmd", + "emmc_clk"; + function = "emmc"; + }; + }; + + sdcard_pins: sdcard { + mux { + groups = "sdcard_d0", + "sdcard_d1", + "sdcard_d2", + "sdcard_d3", + "sdcard_cmd", + "sdcard_clk"; + function = "sdcard"; + }; + }; + + uart_a_pins: uart_a { + mux { + groups = "uart_tx_a", + "uart_rx_a"; + function = "uart_a"; + }; + }; + + uart_b_pins: uart_b { + mux { + groups = "uart_tx_b", + "uart_rx_b"; + function = "uart_b"; + }; + }; + + uart_c_pins: uart_c { + mux { + groups = "uart_tx_c", + "uart_rx_c"; + function = "uart_c"; + }; + }; + + eth_pins: eth_c { + mux { + groups = "eth_mdio", + "eth_mdc", + "eth_clk_rx_clk", + "eth_rx_dv", + "eth_rxd0", + "eth_rxd1", + "eth_rxd2", + "eth_rxd3", + "eth_rgmii_tx_clk", + "eth_tx_en", + "eth_txd0", + "eth_txd1", + "eth_txd2", + "eth_txd3"; + function = "eth"; + }; + }; + }; + }; + + hiubus: hiubus@c883c000 { + compatible = "simple-bus"; + reg = <0x0 0xc883c000 0x0 0x2000>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0x0 0x0 0x0 0xc883c000 0x0 0x2000>; + + clkc: clock-controller@0 { + compatible = "amlogic,gxbb-clkc"; + #clock-cells = <1>; + reg = <0x0 0x0 0x0 0x3db>; + }; + }; + apb: apb@d0000000 { compatible = "simple-bus"; reg = <0x0 0xd0000000 0x0 0x200000>; @@ -174,5 +330,17 @@ #size-cells = <2>; ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>; }; + + ethmac: ethernet@c9410000 { + compatible = "amlogic,meson6-dwmac", "snps,dwmac"; + reg = <0x0 0xc9410000 0x0 0x10000 + 0x0 0xc8834540 0x0 0x4>; + interrupts = <0 8 1>; + interrupt-names = "macirq"; + clocks = <&xtal>; + clock-names = "stmmaceth"; + phy-mode = "rgmii"; + status = "disabled"; + }; }; }; diff --git a/arch/arm64/boot/dts/apm/apm-shadowcat.dtsi b/arch/arm64/boot/dts/apm/apm-shadowcat.dtsi index 2e1e5daa1dc7..1425ed41620c 100644 --- a/arch/arm64/boot/dts/apm/apm-shadowcat.dtsi +++ b/arch/arm64/boot/dts/apm/apm-shadowcat.dtsi @@ -106,88 +106,88 @@ interrupts = <1 9 0xf04>; /* GIC Maintenence IRQ */ ranges = <0 0 0 0x79000000 0x0 0x800000>; /* MSI Range */ reg = <0x0 0x78090000 0x0 0x10000>, /* GIC Dist */ - <0x0 0x780A0000 0x0 0x20000>, /* GIC CPU */ - <0x0 0x780C0000 0x0 0x10000>, /* GIC VCPU Control */ - <0x0 0x780E0000 0x0 0x20000>; /* GIC VCPU */ - v2m0: v2m@0x00000 { + <0x0 0x780a0000 0x0 0x20000>, /* GIC CPU */ + <0x0 0x780c0000 0x0 0x10000>, /* GIC VCPU Control */ + <0x0 0x780e0000 0x0 0x20000>; /* GIC VCPU */ + v2m0: v2m@00000 { compatible = "arm,gic-v2m-frame"; msi-controller; reg = <0x0 0x0 0x0 0x1000>; }; - v2m1: v2m@0x10000 { + v2m1: v2m@10000 { compatible = "arm,gic-v2m-frame"; msi-controller; reg = <0x0 0x10000 0x0 0x1000>; }; - v2m2: v2m@0x20000 { + v2m2: v2m@20000 { compatible = "arm,gic-v2m-frame"; msi-controller; reg = <0x0 0x20000 0x0 0x1000>; }; - v2m3: v2m@0x30000 { + v2m3: v2m@30000 { compatible = "arm,gic-v2m-frame"; msi-controller; reg = <0x0 0x30000 0x0 0x1000>; }; - v2m4: v2m@0x40000 { + v2m4: v2m@40000 { compatible = "arm,gic-v2m-frame"; msi-controller; reg = <0x0 0x40000 0x0 0x1000>; }; - v2m5: v2m@0x50000 { + v2m5: v2m@50000 { compatible = "arm,gic-v2m-frame"; msi-controller; reg = <0x0 0x50000 0x0 0x1000>; }; - v2m6: v2m@0x60000 { + v2m6: v2m@60000 { compatible = "arm,gic-v2m-frame"; msi-controller; reg = <0x0 0x60000 0x0 0x1000>; }; - v2m7: v2m@0x70000 { + v2m7: v2m@70000 { compatible = "arm,gic-v2m-frame"; msi-controller; reg = <0x0 0x70000 0x0 0x1000>; }; - v2m8: v2m@0x80000 { + v2m8: v2m@80000 { compatible = "arm,gic-v2m-frame"; msi-controller; reg = <0x0 0x80000 0x0 0x1000>; }; - v2m9: v2m@0x90000 { + v2m9: v2m@90000 { compatible = "arm,gic-v2m-frame"; msi-controller; reg = <0x0 0x90000 0x0 0x1000>; }; - v2m10: v2m@0xA0000 { + v2m10: v2m@a0000 { compatible = "arm,gic-v2m-frame"; msi-controller; - reg = <0x0 0xA0000 0x0 0x1000>; + reg = <0x0 0xa0000 0x0 0x1000>; }; - v2m11: v2m@0xB0000 { + v2m11: v2m@b0000 { compatible = "arm,gic-v2m-frame"; msi-controller; - reg = <0x0 0xB0000 0x0 0x1000>; + reg = <0x0 0xb0000 0x0 0x1000>; }; - v2m12: v2m@0xC0000 { + v2m12: v2m@c0000 { compatible = "arm,gic-v2m-frame"; msi-controller; - reg = <0x0 0xC0000 0x0 0x1000>; + reg = <0x0 0xc0000 0x0 0x1000>; }; - v2m13: v2m@0xD0000 { + v2m13: v2m@d0000 { compatible = "arm,gic-v2m-frame"; msi-controller; - reg = <0x0 0xD0000 0x0 0x1000>; + reg = <0x0 0xd0000 0x0 0x1000>; }; - v2m14: v2m@0xE0000 { + v2m14: v2m@e0000 { compatible = "arm,gic-v2m-frame"; msi-controller; - reg = <0x0 0xE0000 0x0 0x1000>; + reg = <0x0 0xe0000 0x0 0x1000>; }; - v2m15: v2m@0xF0000 { + v2m15: v2m@f0000 { compatible = "arm,gic-v2m-frame"; msi-controller; - reg = <0x0 0xF0000 0x0 0x1000>; + reg = <0x0 0xf0000 0x0 0x1000>; }; }; @@ -198,10 +198,10 @@ timer { compatible = "arm,armv8-timer"; - interrupts = <1 0 0xff04>, /* Secure Phys IRQ */ - <1 13 0xff04>, /* Non-secure Phys IRQ */ - <1 14 0xff04>, /* Virt IRQ */ - <1 15 0xff04>; /* Hyp IRQ */ + interrupts = <1 0 0xff08>, /* Secure Phys IRQ */ + <1 13 0xff08>, /* Non-secure Phys IRQ */ + <1 14 0xff08>, /* Virt IRQ */ + <1 15 0xff08>; /* Hyp IRQ */ clock-frequency = <50000000>; }; @@ -637,8 +637,8 @@ compatible = "apm,xgene2-sgenet"; status = "disabled"; reg = <0x0 0x1f610000 0x0 0xd100>, - <0x0 0x1f600000 0x0 0Xd100>, - <0x0 0x20000000 0x0 0X20000>; + <0x0 0x1f600000 0x0 0xd100>, + <0x0 0x20000000 0x0 0x20000>; interrupts = <0 96 4>, <0 97 4>; dma-coherent; @@ -652,8 +652,8 @@ compatible = "apm,xgene2-xgenet"; status = "disabled"; reg = <0x0 0x1f620000 0x0 0x10000>, - <0x0 0x1f600000 0x0 0Xd100>, - <0x0 0x20000000 0x0 0X220000>; + <0x0 0x1f600000 0x0 0xd100>, + <0x0 0x20000000 0x0 0x220000>; interrupts = <0 108 4>, <0 109 4>, <0 110 4>, @@ -693,7 +693,7 @@ #size-cells = <0>; compatible = "snps,designware-i2c"; reg = <0x0 0x10640000 0x0 0x1000>; - interrupts = <0 0x3A 0x4>; + interrupts = <0 0x3a 0x4>; clocks = <&i2c4clk 0>; bus_num = <4>; }; diff --git a/arch/arm64/boot/dts/apm/apm-storm.dtsi b/arch/arm64/boot/dts/apm/apm-storm.dtsi index 6bf7cbe2e72d..f1c2c713f9b0 100644 --- a/arch/arm64/boot/dts/apm/apm-storm.dtsi +++ b/arch/arm64/boot/dts/apm/apm-storm.dtsi @@ -199,16 +199,6 @@ clock-output-names = "sdioclk"; }; - qmlclk: qmlclk { - compatible = "apm,xgene-device-clock"; - #clock-cells = <1>; - clocks = <&socplldiv2 0>; - clock-names = "qmlclk"; - reg = <0x0 0x1703C000 0x0 0x1000>; - reg-names = "csr-reg"; - clock-output-names = "qmlclk"; - }; - ethclk: ethclk { compatible = "apm,xgene-device-clock"; #clock-cells = <1>; @@ -226,7 +216,7 @@ compatible = "apm,xgene-device-clock"; #clock-cells = <1>; clocks = <ðclk 0>; - reg = <0x0 0x1702C000 0x0 0x1000>; + reg = <0x0 0x1702c000 0x0 0x1000>; reg-names = "csr-reg"; clock-output-names = "menetclk"; }; @@ -924,8 +914,8 @@ compatible = "apm,xgene-enet"; status = "disabled"; reg = <0x0 0x17020000 0x0 0xd100>, - <0x0 0X17030000 0x0 0Xc300>, - <0x0 0X10000000 0x0 0X200>; + <0x0 0x17030000 0x0 0xc300>, + <0x0 0x10000000 0x0 0x200>; reg-names = "enet_csr", "ring_csr", "ring_cmd"; interrupts = <0x0 0x3c 0x4>; dma-coherent; @@ -950,11 +940,11 @@ compatible = "apm,xgene1-sgenet"; status = "disabled"; reg = <0x0 0x1f210000 0x0 0xd100>, - <0x0 0x1f200000 0x0 0Xc300>, - <0x0 0x1B000000 0x0 0X200>; + <0x0 0x1f200000 0x0 0xc300>, + <0x0 0x1b000000 0x0 0x200>; reg-names = "enet_csr", "ring_csr", "ring_cmd"; - interrupts = <0x0 0xA0 0x4>, - <0x0 0xA1 0x4>; + interrupts = <0x0 0xa0 0x4>, + <0x0 0xa1 0x4>; dma-coherent; clocks = <&sge0clk 0>; local-mac-address = [00 00 00 00 00 00]; @@ -966,11 +956,11 @@ compatible = "apm,xgene1-sgenet"; status = "disabled"; reg = <0x0 0x1f210030 0x0 0xd100>, - <0x0 0x1f200000 0x0 0Xc300>, - <0x0 0x1B000000 0x0 0X8000>; + <0x0 0x1f200000 0x0 0xc300>, + <0x0 0x1b000000 0x0 0x8000>; reg-names = "enet_csr", "ring_csr", "ring_cmd"; - interrupts = <0x0 0xAC 0x4>, - <0x0 0xAD 0x4>; + interrupts = <0x0 0xac 0x4>, + <0x0 0xad 0x4>; port-id = <1>; dma-coherent; local-mac-address = [00 00 00 00 00 00]; @@ -982,8 +972,8 @@ compatible = "apm,xgene1-xgenet"; status = "disabled"; reg = <0x0 0x1f610000 0x0 0xd100>, - <0x0 0x1f600000 0x0 0Xc300>, - <0x0 0x18000000 0x0 0X200>; + <0x0 0x1f600000 0x0 0xc300>, + <0x0 0x18000000 0x0 0x200>; reg-names = "enet_csr", "ring_csr", "ring_cmd"; interrupts = <0x0 0x60 0x4>, <0x0 0x61 0x4>, @@ -1005,11 +995,11 @@ compatible = "apm,xgene1-xgenet"; status = "disabled"; reg = <0x0 0x1f620000 0x0 0xd100>, - <0x0 0x1f600000 0x0 0Xc300>, - <0x0 0x18000000 0x0 0X8000>; + <0x0 0x1f600000 0x0 0xc300>, + <0x0 0x18000000 0x0 0x8000>; reg-names = "enet_csr", "ring_csr", "ring_cmd"; - interrupts = <0x0 0x6C 0x4>, - <0x0 0x6D 0x4>; + interrupts = <0x0 0x6c 0x4>, + <0x0 0x6d 0x4>; port-id = <1>; dma-coherent; clocks = <&xge1clk 0>; diff --git a/arch/arm64/boot/dts/arm/juno-base.dtsi b/arch/arm64/boot/dts/arm/juno-base.dtsi index dee2386d3b9b..334271a25f70 100644 --- a/arch/arm64/boot/dts/arm/juno-base.dtsi +++ b/arch/arm64/boot/dts/arm/juno-base.dtsi @@ -56,6 +56,315 @@ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>; }; + /* + * Juno TRMs specify the size for these coresight components as 64K. + * The actual size is just 4K though 64K is reserved. Access to the + * unmapped reserved region results in a DECERR response. + */ + etf@20010000 { + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0 0x20010000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* input port */ + port@0 { + reg = <0>; + etf_in_port: endpoint { + slave-mode; + remote-endpoint = <&main_funnel_out_port>; + }; + }; + + /* output port */ + port@1 { + reg = <0>; + etf_out_port: endpoint { + remote-endpoint = <&replicator_in_port0>; + }; + }; + }; + }; + + tpiu@20030000 { + compatible = "arm,coresight-tpiu", "arm,primecell"; + reg = <0 0x20030000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + port { + tpiu_in_port: endpoint { + slave-mode; + remote-endpoint = <&replicator_out_port0>; + }; + }; + }; + + main-funnel@20040000 { + compatible = "arm,coresight-funnel", "arm,primecell"; + reg = <0 0x20040000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + main_funnel_out_port: endpoint { + remote-endpoint = <&etf_in_port>; + }; + }; + + port@1 { + reg = <0>; + main_funnel_in_port0: endpoint { + slave-mode; + remote-endpoint = <&cluster0_funnel_out_port>; + }; + }; + + port@2 { + reg = <1>; + main_funnel_in_port1: endpoint { + slave-mode; + remote-endpoint = <&cluster1_funnel_out_port>; + }; + }; + + }; + }; + + etr@20070000 { + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0 0x20070000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + port { + etr_in_port: endpoint { + slave-mode; + remote-endpoint = <&replicator_out_port1>; + }; + }; + }; + + etm0: etm@22040000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x22040000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + port { + cluster0_etm0_out_port: endpoint { + remote-endpoint = <&cluster0_funnel_in_port0>; + }; + }; + }; + + cluster0-funnel@220c0000 { + compatible = "arm,coresight-funnel", "arm,primecell"; + reg = <0 0x220c0000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + cluster0_funnel_out_port: endpoint { + remote-endpoint = <&main_funnel_in_port0>; + }; + }; + + port@1 { + reg = <0>; + cluster0_funnel_in_port0: endpoint { + slave-mode; + remote-endpoint = <&cluster0_etm0_out_port>; + }; + }; + + port@2 { + reg = <1>; + cluster0_funnel_in_port1: endpoint { + slave-mode; + remote-endpoint = <&cluster0_etm1_out_port>; + }; + }; + }; + }; + + etm1: etm@22140000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x22140000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + port { + cluster0_etm1_out_port: endpoint { + remote-endpoint = <&cluster0_funnel_in_port1>; + }; + }; + }; + + etm2: etm@23040000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x23040000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + port { + cluster1_etm0_out_port: endpoint { + remote-endpoint = <&cluster1_funnel_in_port0>; + }; + }; + }; + + cluster1-funnel@230c0000 { + compatible = "arm,coresight-funnel", "arm,primecell"; + reg = <0 0x230c0000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + cluster1_funnel_out_port: endpoint { + remote-endpoint = <&main_funnel_in_port1>; + }; + }; + + port@1 { + reg = <0>; + cluster1_funnel_in_port0: endpoint { + slave-mode; + remote-endpoint = <&cluster1_etm0_out_port>; + }; + }; + + port@2 { + reg = <1>; + cluster1_funnel_in_port1: endpoint { + slave-mode; + remote-endpoint = <&cluster1_etm1_out_port>; + }; + }; + port@3 { + reg = <2>; + cluster1_funnel_in_port2: endpoint { + slave-mode; + remote-endpoint = <&cluster1_etm2_out_port>; + }; + }; + port@4 { + reg = <3>; + cluster1_funnel_in_port3: endpoint { + slave-mode; + remote-endpoint = <&cluster1_etm3_out_port>; + }; + }; + }; + }; + + etm3: etm@23140000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x23140000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + port { + cluster1_etm1_out_port: endpoint { + remote-endpoint = <&cluster1_funnel_in_port1>; + }; + }; + }; + + etm4: etm@23240000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x23240000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + port { + cluster1_etm2_out_port: endpoint { + remote-endpoint = <&cluster1_funnel_in_port2>; + }; + }; + }; + + etm5: etm@23340000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x23340000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + port { + cluster1_etm3_out_port: endpoint { + remote-endpoint = <&cluster1_funnel_in_port3>; + }; + }; + }; + + coresight-replicator { + /* + * Non-configurable replicators don't show up on the + * AMBA bus. As such no need to add "arm,primecell". + */ + compatible = "arm,coresight-replicator"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* replicator output ports */ + port@0 { + reg = <0>; + replicator_out_port0: endpoint { + remote-endpoint = <&tpiu_in_port>; + }; + }; + + port@1 { + reg = <1>; + replicator_out_port1: endpoint { + remote-endpoint = <&etr_in_port>; + }; + }; + + /* replicator input port */ + port@2 { + reg = <0>; + replicator_in_port0: endpoint { + slave-mode; + remote-endpoint = <&etf_out_port>; + }; + }; + }; + }; + sram: sram@2e000000 { compatible = "arm,juno-sram-ns", "mmio-sram"; reg = <0x0 0x2e000000 0x0 0x8000>; @@ -119,12 +428,60 @@ }; }; + scpi_devpd: scpi-power-domains { + compatible = "arm,scpi-power-domains"; + num-domains = <2>; + #power-domain-cells = <1>; + }; + scpi_sensors0: sensors { compatible = "arm,scpi-sensors"; #thermal-sensor-cells = <1>; }; }; + thermal-zones { + pmic { + polling-delay = <1000>; + polling-delay-passive = <100>; + thermal-sensors = <&scpi_sensors0 0>; + }; + + soc { + polling-delay = <1000>; + polling-delay-passive = <100>; + thermal-sensors = <&scpi_sensors0 3>; + }; + + big_cluster_thermal_zone: big_cluster { + polling-delay = <1000>; + polling-delay-passive = <100>; + thermal-sensors = <&scpi_sensors0 21>; + status = "disabled"; + }; + + little_cluster_thermal_zone: little_cluster { + polling-delay = <1000>; + polling-delay-passive = <100>; + thermal-sensors = <&scpi_sensors0 22>; + status = "disabled"; + }; + + gpu0_thermal_zone: gpu0 { + polling-delay = <1000>; + polling-delay-passive = <100>; + thermal-sensors = <&scpi_sensors0 23>; + status = "disabled"; + }; + + gpu1_thermal_zone: gpu1 { + polling-delay = <1000>; + polling-delay-passive = <100>; + thermal-sensors = <&scpi_sensors0 24>; + status = "disabled"; + }; + }; + /include/ "juno-clocks.dtsi" dma@7ff00000 { diff --git a/arch/arm64/boot/dts/arm/juno-r1.dts b/arch/arm64/boot/dts/arm/juno-r1.dts index d95d9e7e2dc0..123a58b29cbd 100644 --- a/arch/arm64/boot/dts/arm/juno-r1.dts +++ b/arch/arm64/boot/dts/arm/juno-r1.dts @@ -181,3 +181,43 @@ &pcie_ctlr { status = "okay"; }; + +&etm0 { + cpu = <&A57_0>; +}; + +&etm1 { + cpu = <&A57_1>; +}; + +&etm2 { + cpu = <&A53_0>; +}; + +&etm3 { + cpu = <&A53_1>; +}; + +&etm4 { + cpu = <&A53_2>; +}; + +&etm5 { + cpu = <&A53_3>; +}; + +&big_cluster_thermal_zone { + status = "okay"; +}; + +&little_cluster_thermal_zone { + status = "okay"; +}; + +&gpu0_thermal_zone { + status = "okay"; +}; + +&gpu1_thermal_zone { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/arm/juno-r2.dts b/arch/arm64/boot/dts/arm/juno-r2.dts index 88ecd6182b67..007be826efce 100644 --- a/arch/arm64/boot/dts/arm/juno-r2.dts +++ b/arch/arm64/boot/dts/arm/juno-r2.dts @@ -181,3 +181,43 @@ &pcie_ctlr { status = "okay"; }; + +&etm0 { + cpu = <&A72_0>; +}; + +&etm1 { + cpu = <&A72_1>; +}; + +&etm2 { + cpu = <&A53_0>; +}; + +&etm3 { + cpu = <&A53_1>; +}; + +&etm4 { + cpu = <&A53_2>; +}; + +&etm5 { + cpu = <&A53_3>; +}; + +&big_cluster_thermal_zone { + status = "okay"; +}; + +&little_cluster_thermal_zone { + status = "okay"; +}; + +&gpu0_thermal_zone { + status = "okay"; +}; + +&gpu1_thermal_zone { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/arm/juno.dts b/arch/arm64/boot/dts/arm/juno.dts index dcfcf15a17f5..a7270eff6939 100644 --- a/arch/arm64/boot/dts/arm/juno.dts +++ b/arch/arm64/boot/dts/arm/juno.dts @@ -173,3 +173,27 @@ #include "juno-base.dtsi" }; + +&etm0 { + cpu = <&A57_0>; +}; + +&etm1 { + cpu = <&A57_1>; +}; + +&etm2 { + cpu = <&A53_0>; +}; + +&etm3 { + cpu = <&A53_1>; +}; + +&etm4 { + cpu = <&A53_2>; +}; + +&etm5 { + cpu = <&A53_3>; +}; diff --git a/arch/arm64/boot/dts/broadcom/Makefile b/arch/arm64/boot/dts/broadcom/Makefile index bec1f8b36f60..05faf2a8a35c 100644 --- a/arch/arm64/boot/dts/broadcom/Makefile +++ b/arch/arm64/boot/dts/broadcom/Makefile @@ -1,3 +1,4 @@ +dtb-$(CONFIG_ARCH_BCM2835) += bcm2837-rpi-3-b.dtb dtb-$(CONFIG_ARCH_BCM_IPROC) += ns2-svk.dtb dtb-$(CONFIG_ARCH_VULCAN) += vulcan-eval.dtb diff --git a/arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-b.dts b/arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-b.dts new file mode 100644 index 000000000000..6f47dd2bb1db --- /dev/null +++ b/arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-b.dts @@ -0,0 +1,30 @@ +/dts-v1/; +#include "bcm2837.dtsi" +#include "../../../../arm/boot/dts/bcm2835-rpi.dtsi" +#include "../../../../arm/boot/dts/bcm283x-rpi-smsc9514.dtsi" + +/ { + compatible = "raspberrypi,3-model-b", "brcm,bcm2837"; + model = "Raspberry Pi 3 Model B"; + + memory { + reg = <0 0x40000000>; + }; + + leds { + act { + gpios = <&gpio 47 0>; + }; + + pwr { + label = "PWR"; + gpios = <&gpio 35 0>; + default-state = "keep"; + linux,default-trigger = "default-on"; + }; + }; +}; + +&uart1 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/broadcom/bcm2837.dtsi b/arch/arm64/boot/dts/broadcom/bcm2837.dtsi new file mode 100644 index 000000000000..f2a31d06845d --- /dev/null +++ b/arch/arm64/boot/dts/broadcom/bcm2837.dtsi @@ -0,0 +1,76 @@ +#include "../../../../arm/boot/dts/bcm283x.dtsi" + +/ { + compatible = "brcm,bcm2836"; + + soc { + ranges = <0x7e000000 0x3f000000 0x1000000>, + <0x40000000 0x40000000 0x00001000>; + dma-ranges = <0xc0000000 0x00000000 0x3f000000>; + + local_intc: local_intc { + compatible = "brcm,bcm2836-l1-intc"; + reg = <0x40000000 0x100>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&local_intc>; + }; + }; + + timer { + compatible = "arm,armv7-timer"; + interrupt-parent = <&local_intc>; + interrupts = <0>, // PHYS_SECURE_PPI + <1>, // PHYS_NONSECURE_PPI + <3>, // VIRT_PPI + <2>; // HYP_PPI + always-on; + }; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0>; + enable-method = "spin-table"; + cpu-release-addr = <0x0 0x000000d8>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <1>; + enable-method = "spin-table"; + cpu-release-addr = <0x0 0x000000e0>; + }; + + cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <2>; + enable-method = "spin-table"; + cpu-release-addr = <0x0 0x000000e8>; + }; + + cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <3>; + enable-method = "spin-table"; + cpu-release-addr = <0x0 0x000000f0>; + }; + }; +}; + +/* Make the BCM2835-style global interrupt controller be a child of the + * CPU-local interrupt controller. + */ +&intc { + compatible = "brcm,bcm2836-armctrl-ic"; + reg = <0x7e00b200 0x200>; + interrupt-parent = <&local_intc>; + interrupts = <8>; +}; diff --git a/arch/arm64/boot/dts/broadcom/ns2-svk.dts b/arch/arm64/boot/dts/broadcom/ns2-svk.dts index ea5603fd106a..2d7872a36b91 100644 --- a/arch/arm64/boot/dts/broadcom/ns2-svk.dts +++ b/arch/arm64/boot/dts/broadcom/ns2-svk.dts @@ -40,10 +40,14 @@ aliases { serial0 = &uart3; + serial1 = &uart0; + serial2 = &uart1; + serial3 = &uart2; }; chosen { stdout-path = "serial0:115200n8"; + bootargs = "earlycon=uart8250,mmio32,0x66130000"; }; memory { @@ -76,6 +80,18 @@ status = "ok"; }; +&uart0 { + status = "ok"; +}; + +&uart1 { + status = "ok"; +}; + +&uart2 { + status = "ok"; +}; + &uart3 { status = "ok"; }; @@ -125,6 +141,18 @@ }; }; +&sata_phy0 { + status = "ok"; +}; + +&sata_phy1 { + status = "ok"; +}; + +&sata { + status = "ok"; +}; + &sdio0 { status = "ok"; }; @@ -148,3 +176,12 @@ }; }; }; + +&pinctrl { + pinctrl-names = "default"; + pinctrl-0 = <&nand_sel>; + nand_sel: nand_sel { + function = "nand"; + groups = "nand_grp"; + }; +}; diff --git a/arch/arm64/boot/dts/broadcom/ns2.dtsi b/arch/arm64/boot/dts/broadcom/ns2.dtsi index 46b78fa89f4c..f53b0955bfd3 100644 --- a/arch/arm64/boot/dts/broadcom/ns2.dtsi +++ b/arch/arm64/boot/dts/broadcom/ns2.dtsi @@ -251,6 +251,22 @@ mmu-masters; }; + pinctrl: pinctrl@6501d130 { + compatible = "brcm,ns2-pinmux"; + reg = <0x6501d130 0x08>, + <0x660a0028 0x04>, + <0x660009b0 0x40>; + }; + + gpio_aon: gpio@65024800 { + compatible = "brcm,iproc-gpio"; + reg = <0x65024800 0x50>, + <0x65024008 0x18>; + ngpios = <6>; + #gpio-cells = <2>; + gpio-controller; + }; + gic: interrupt-controller@65210000 { compatible = "arm,gic-400"; #interrupt-cells = <3>; @@ -263,6 +279,26 @@ IRQ_TYPE_LEVEL_HIGH)>; }; + cci@65590000 { + compatible = "arm,cci-400"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x65590000 0x1000>; + ranges = <0 0x65590000 0x10000>; + + pmu@9000 { + compatible = "arm,cci-400-pmu,r1", + "arm,cci-400-pmu"; + reg = <0x9000 0x4000>; + interrupts = <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 349 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + mdio_mux_iproc: mdio-mux@6602023c { compatible = "brcm,mdio-mux-iproc"; reg = <0x6602023c 0x14>; @@ -360,6 +396,16 @@ clock-names = "wdogclk", "apb_pclk"; }; + gpio_g: gpio@660a0000 { + compatible = "brcm,iproc-gpio"; + reg = <0x660a0000 0x50>; + ngpios = <32>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + interrupts = <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>; + }; + i2c1: i2c@660b0000 { compatible = "brcm,iproc-i2c"; reg = <0x660b0000 0x100>; @@ -370,6 +416,36 @@ status = "disabled"; }; + uart0: serial@66100000 { + compatible = "snps,dw-apb-uart"; + reg = <0x66100000 0x100>; + interrupts = <GIC_SPI 390 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&iprocslow>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart1: serial@66110000 { + compatible = "snps,dw-apb-uart"; + reg = <0x66110000 0x100>; + interrupts = <GIC_SPI 391 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&iprocslow>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart2: serial@66120000 { + compatible = "snps,dw-apb-uart"; + reg = <0x66120000 0x100>; + interrupts = <GIC_SPI 392 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&iprocslow>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + uart3: serial@66130000 { compatible = "snps,dw-apb-uart"; reg = <0x66130000 0x100>; @@ -407,6 +483,49 @@ reg = <0x66220000 0x28>; }; + sata_phy: sata_phy@663f0100 { + compatible = "brcm,iproc-ns2-sata-phy"; + reg = <0x663f0100 0x1f00>, + <0x663f004c 0x10>; + reg-names = "phy", "phy-ctrl"; + #address-cells = <1>; + #size-cells = <0>; + + sata_phy0: sata-phy@0 { + reg = <0>; + #phy-cells = <0>; + status = "disabled"; + }; + + sata_phy1: sata-phy@1 { + reg = <1>; + #phy-cells = <0>; + status = "disabled"; + }; + }; + + sata: ahci@663f2000 { + compatible = "brcm,iproc-ahci", "generic-ahci"; + reg = <0x663f2000 0x1000>; + reg-names = "ahci"; + interrupts = <GIC_SPI 438 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + sata0: sata-port@0 { + reg = <0>; + phys = <&sata_phy0>; + phy-names = "sata-phy"; + }; + + sata1: sata-port@1 { + reg = <1>; + phys = <&sata_phy1>; + phy-names = "sata-phy"; + }; + }; + sdio0: sdhci@66420000 { compatible = "brcm,sdhci-iproc-cygnus"; reg = <0x66420000 0x100>; diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts index d8767b00862e..299f3ce969ab 100644 --- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts +++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts @@ -249,7 +249,7 @@ buck2_reg: BUCK2 { regulator-name = "vdd_atlas"; - regulator-min-microvolt = <1200000>; + regulator-min-microvolt = <500000>; regulator-max-microvolt = <1200000>; regulator-always-on; regulator-boot-on; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi index 6bd46c133010..e669fbd7f9c3 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi @@ -51,7 +51,7 @@ #size-cells = <2>; cpus { - #address-cells = <2>; + #address-cells = <1>; #size-cells = <0>; /* @@ -63,29 +63,37 @@ cpu0: cpu@0 { device_type = "cpu"; compatible = "arm,cortex-a53"; - reg = <0x0 0x0>; + reg = <0x0>; clocks = <&clockgen 1 0>; + next-level-cache = <&l2>; }; cpu1: cpu@1 { device_type = "cpu"; compatible = "arm,cortex-a53"; - reg = <0x0 0x1>; + reg = <0x1>; clocks = <&clockgen 1 0>; + next-level-cache = <&l2>; }; cpu2: cpu@2 { device_type = "cpu"; compatible = "arm,cortex-a53"; - reg = <0x0 0x2>; + reg = <0x2>; clocks = <&clockgen 1 0>; + next-level-cache = <&l2>; }; cpu3: cpu@3 { device_type = "cpu"; compatible = "arm,cortex-a53"; - reg = <0x0 0x3>; + reg = <0x3>; clocks = <&clockgen 1 0>; + next-level-cache = <&l2>; + }; + + l2: l2-cache { + compatible = "cache"; }; }; @@ -465,6 +473,7 @@ interrupts = <0 60 0x4>; dr_mode = "host"; snps,quirk-frame-length-adjustment = <0x20>; + snps,dis_rxdet_inp3_quirk; }; usb1: usb3@3000000 { @@ -473,6 +482,7 @@ interrupts = <0 61 0x4>; dr_mode = "host"; snps,quirk-frame-length-adjustment = <0x20>; + snps,dis_rxdet_inp3_quirk; }; usb2: usb3@3100000 { @@ -481,6 +491,7 @@ interrupts = <0 63 0x4>; dr_mode = "host"; snps,quirk-frame-length-adjustment = <0x20>; + snps,dis_rxdet_inp3_quirk; }; sata: sata@3200000 { @@ -522,6 +533,7 @@ #address-cells = <3>; #size-cells = <2>; device_type = "pci"; + dma-coherent; num-lanes = <4>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */ @@ -546,6 +558,7 @@ #address-cells = <3>; #size-cells = <2>; device_type = "pci"; + dma-coherent; num-lanes = <2>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x48 0x00010000 0x0 0x00010000 /* downstream I/O */ @@ -570,6 +583,7 @@ #address-cells = <3>; #size-cells = <2>; device_type = "pci"; + dma-coherent; num-lanes = <2>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x50 0x00010000 0x0 0x00010000 /* downstream I/O */ diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi index 3187c822afa3..21023a388c29 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi @@ -51,7 +51,7 @@ #size-cells = <2>; cpus { - #address-cells = <2>; + #address-cells = <1>; #size-cells = <0>; /* @@ -65,57 +65,81 @@ cpu@0 { device_type = "cpu"; compatible = "arm,cortex-a57"; - reg = <0x0 0x0>; + reg = <0x0>; clocks = <&clockgen 1 0>; + next-level-cache = <&cluster0_l2>; }; cpu@1 { device_type = "cpu"; compatible = "arm,cortex-a57"; - reg = <0x0 0x1>; + reg = <0x1>; clocks = <&clockgen 1 0>; + next-level-cache = <&cluster0_l2>; }; cpu@100 { device_type = "cpu"; compatible = "arm,cortex-a57"; - reg = <0x0 0x100>; + reg = <0x100>; clocks = <&clockgen 1 1>; + next-level-cache = <&cluster1_l2>; }; cpu@101 { device_type = "cpu"; compatible = "arm,cortex-a57"; - reg = <0x0 0x101>; + reg = <0x101>; clocks = <&clockgen 1 1>; + next-level-cache = <&cluster1_l2>; }; cpu@200 { device_type = "cpu"; compatible = "arm,cortex-a57"; - reg = <0x0 0x200>; + reg = <0x200>; clocks = <&clockgen 1 2>; + next-level-cache = <&cluster2_l2>; }; cpu@201 { device_type = "cpu"; compatible = "arm,cortex-a57"; - reg = <0x0 0x201>; + reg = <0x201>; clocks = <&clockgen 1 2>; + next-level-cache = <&cluster2_l2>; }; cpu@300 { device_type = "cpu"; compatible = "arm,cortex-a57"; - reg = <0x0 0x300>; + reg = <0x300>; clocks = <&clockgen 1 3>; + next-level-cache = <&cluster3_l2>; }; cpu@301 { device_type = "cpu"; compatible = "arm,cortex-a57"; - reg = <0x0 0x301>; + reg = <0x301>; clocks = <&clockgen 1 3>; + next-level-cache = <&cluster3_l2>; + }; + + cluster0_l2: l2-cache0 { + compatible = "cache"; + }; + + cluster1_l2: l2-cache1 { + compatible = "cache"; + }; + + cluster2_l2: l2-cache2 { + compatible = "cache"; + }; + + cluster3_l2: l2-cache3 { + compatible = "cache"; }; }; @@ -672,6 +696,7 @@ interrupts = <0 80 0x4>; /* Level high type */ dr_mode = "host"; snps,quirk-frame-length-adjustment = <0x20>; + snps,dis_rxdet_inp3_quirk; }; usb1: usb3@3110000 { @@ -681,6 +706,7 @@ interrupts = <0 81 0x4>; /* Level high type */ dr_mode = "host"; snps,quirk-frame-length-adjustment = <0x20>; + snps,dis_rxdet_inp3_quirk; }; ccn@4000000 { diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts index e92a30c87a82..593c7e43de79 100644 --- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts +++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts @@ -66,6 +66,149 @@ status = "ok"; }; + /* + * Legend: proper name = the GPIO line is used as GPIO + * NC = not connected (not routed from the SoC) + * "[PER]" = pin is muxed for peripheral (not GPIO) + * "" = no idea, schematic doesn't say, could be + * unrouted (not connected to any external pin) + * LSEC = Low Speed External Connector + * HSEC = High Speed External Connector + * + * Pin assignments taken from LeMaker and CircuitCo Schematics + * Rev A1. + * + * For the lines routed to the external connectors the + * lines are named after the 96Boards CE Specification 1.0, + * Appendix "Expansion Connector Signal Description". + * + * When the 96Board naming of a line and the schematic name of + * the same line are in conflict, the 96Board specification + * takes precedence, which means that the external UART on the + * LSEC is named UART0 while the schematic and SoC names this + * UART2. This is only for the informational lines i.e. "[FOO]", + * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only + * ones actually used for GPIO. + */ + gpio0: gpio@f8011000 { + gpio-line-names = "PWR_HOLD", "DSI_SEL", + "USB_HUB_RESET_N", "USB_SEL", "HDMI_PD", "WL_REG_ON", + "PWRON_DET", "5V_HUB_EN"; + }; + + gpio1: gpio@f8012000 { + gpio-line-names = "SD_DET", "HDMI_INT", "PMU_IRQ_N", + "WL_HOST_WAKE", "NC", "NC", "NC", "BT_REG_ON"; + }; + + gpio2: gpio@f8013000 { + gpio-line-names = + "GPIO-A", /* LSEC Pin 23: GPIO2_0 */ + "GPIO-B", /* LSEC Pin 24: GPIO2_1 */ + "GPIO-C", /* LSEC Pin 25: GPIO2_2 */ + "GPIO-D", /* LSEC Pin 26: GPIO2_3 */ + "GPIO-E", /* LSEC Pin 27: GPIO2_4 */ + "USB_ID_DET", "USB_VBUS_DET", + "GPIO-H"; /* LSEC Pin 30: GPIO2_7 */ + }; + + gpio3: gpio@f8014000 { + gpio-line-names = "GPIO3_0", "NC", "NC", "", "NC", "", + "WLAN_ACTIVE", "NC", "NC"; + }; + + gpio4: gpio@f7020000 { + gpio-line-names = "USER_LED1", "USER_LED2", "USER_LED3", + "USER_LED4", "SD_SEL", "NC", "NC", "BT_ACTIVE"; + }; + + gpio5: gpio@f7021000 { + gpio-line-names = "NC", "NC", + "[UART1_RxD]", /* LSEC Pin 11: UART3_RX */ + "[UART1_TxD]", /* LSEC Pin 13: UART3_TX */ + "[AUX_SSI1]", "NC", + "[PCM_CLK]", /* LSEC Pin 18: MODEM_PCM_XCLK */ + "[PCM_FS]"; /* LSEC Pin 16: MODEM_PCM_XFS */ + }; + + gpio6: gpio@f7022000 { + gpio-line-names = + "[SPI0_DIN]", /* Pin 10: SPI0_DI */ + "[SPI0_DOUT]", /* Pin 14: SPI0_DO */ + "[SPI0_CS]", /* Pin 12: SPI0_CS_N */ + "[SPI0_SCLK]", /* Pin 8: SPI0_SCLK */ + "NC", "NC", "NC", + "GPIO-G"; /* Pin 29: GPIO6_7_DSI_TE0 */ + }; + + gpio7: gpio@f7023000 { + gpio-line-names = "NC", "NC", "NC", "NC", + "[PCM_DI]", /* Pin 22: MODEM_PCM_DI */ + "[PCM_DO]", /* Pin 20: MODEM_PCM_DO */ + "NC", "NC"; + }; + + gpio8: gpio@f7024000 { + gpio-line-names = "NC", "[CEC_CLK_19_2MHZ]", "NC", + "", "", "", "", "", ""; + }; + + gpio9: gpio@f7025000 { + gpio-line-names = "", + "GPIO-J", /* LSEC Pin 32: ISP_PWDN0_GPIO9_1 */ + "GPIO-L", /* LSEC Pin 34: ISP_PWDN1_GPIO9_2 */ + "NC", "NC", "NC", "NC", "[ISP_CCLK0]"; + }; + + gpio10: gpio@f7026000 { + gpio-line-names = "BOOT_SEL", + "[ISP_CCLK1]", + "GPIO-I", /* LSEC Pin 31: ISP_RSTB0_GPIO10_2 */ + "GPIO-K", /* LSEC Pin 33: ISP_RSTB1_GPIO10_3 */ + "NC", "NC", + "[I2C2_SDA]", /* HSEC Pin 34: ISP0_SDA */ + "[I2C2_SCL]"; /* HSEC Pin 32: ISP0_SCL */ + }; + + gpio11: gpio@f7027000 { + gpio-line-names = + "[I2C3_SDA]", /* HSEC Pin 38: ISP1_SDA */ + "[I2C3_SCL]", /* HSEC Pin 36: ISP1_SCL */ + "", "NC", "NC", "NC", "", ""; + }; + + gpio12: gpio@f7028000 { + gpio-line-names = "[BT_PCM_XFS]", "[BT_PCM_DI]", + "[BT_PCM_DO]", + "NC", "NC", "NC", "NC", + "GPIO-F"; /* LSEC Pin 28: BL_PWM_GPIO12_7 */ + }; + + gpio13: gpio@f7029000 { + gpio-line-names = "[UART0_RX]", "[UART0_TX]", + "[BT_UART1_CTS]", "[BT_UART1_RTS]", + "[BT_UART1_RX]", "[BT_UART1_TX]", + "[UART0_CTS]", /* LSEC Pin 3: UART2_CTS_N */ + "[UART0_RTS]"; /* LSEC Pin 9: UART2_RTS_N */ + }; + + gpio14: gpio@f702a000 { + gpio-line-names = + "[UART0_RxD]", /* LSEC Pin 7: UART2_RX */ + "[UART0_TxD]", /* LSEC Pin 5: UART2_TX */ + "[I2C0_SCL]", /* LSEC Pin 15: I2C0_SCL */ + "[I2C0_SDA]", /* LSEC Pin 17: I2C0_SDA */ + "[I2C1_SCL]", /* LSEC Pin 19: I2C1_SCL */ + "[I2C1_SDA]", /* LSEC Pin 21: I2C1_SDA */ + "[I2C2_SCL]", "[I2C2_SDA]"; + }; + + gpio15: gpio@f702b000 { + gpio-line-names = "", "", "", "", "", "", "NC", ""; + }; + + /* GPIO blocks 16 thru 19 do not appear to be routed to pins */ + dwmmc_2: dwmmc2@f723f000 { ti,non-removable; non-removable; diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi index c19b82799a34..4f270410a5cb 100644 --- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi @@ -338,6 +338,22 @@ clock-names = "timer1", "timer2", "apb_pclk"; }; + rtc0: rtc@f8003000 { + compatible = "arm,pl031", "arm,primecell"; + reg = <0x0 0xf8003000 0x0 0x1000>; + interrupts = <0 12 4>; + clocks = <&ao_ctrl HI6220_RTC0_PCLK>; + clock-names = "apb_pclk"; + }; + + rtc1: rtc@f8004000 { + compatible = "arm,pl031", "arm,primecell"; + reg = <0x0 0xf8004000 0x0 0x1000>; + interrupts = <0 8 4>; + clocks = <&ao_ctrl HI6220_RTC1_PCLK>; + clock-names = "apb_pclk"; + }; + pmx0: pinmux@f7010000 { compatible = "pinctrl-single"; reg = <0x0 0xf7010000 0x0 0x27c>; diff --git a/arch/arm64/boot/dts/lg/Makefile b/arch/arm64/boot/dts/lg/Makefile index b0cc64964171..5c7b54c12adc 100644 --- a/arch/arm64/boot/dts/lg/Makefile +++ b/arch/arm64/boot/dts/lg/Makefile @@ -1,4 +1,5 @@ dtb-$(CONFIG_ARCH_LG1K) += lg1312-ref.dtb +dtb-$(CONFIG_ARCH_LG1K) += lg1313-ref.dtb always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/lg/lg1313-ref.dts b/arch/arm64/boot/dts/lg/lg1313-ref.dts new file mode 100644 index 000000000000..df0ece43cfbf --- /dev/null +++ b/arch/arm64/boot/dts/lg/lg1313-ref.dts @@ -0,0 +1,36 @@ +/* + * dts file for lg1313 Reference Board. + * + * Copyright (C) 2016, LG Electronics + */ + +/dts-v1/; + +#include "lg1313.dtsi" + +/ { + #address-cells = <2>; + #size-cells = <1>; + + model = "LG Electronics, DTV SoC LG1313 Reference Board"; + compatible = "lge,lg1313-ref", "lge,lg1313"; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + }; + + memory { + device_type = "memory"; + reg = <0x0 0x00000000 0x20000000>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/lg/lg1313.dtsi b/arch/arm64/boot/dts/lg/lg1313.dtsi new file mode 100644 index 000000000000..e703e1149c75 --- /dev/null +++ b/arch/arm64/boot/dts/lg/lg1313.dtsi @@ -0,0 +1,351 @@ +/* + * dts file for lg1313 SoC + * + * Copyright (C) 2016, LG Electronics + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> + +/ { + #address-cells = <2>; + #size-cells = <2>; + + compatible = "lge,lg1313"; + interrupt-parent = <&gic>; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x0>; + next-level-cache = <&L2_0>; + }; + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x1>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x2>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x3>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + L2_0: l2-cache0 { + compatible = "cache"; + }; + }; + + psci { + compatible = "arm,psci-0.2", "arm,psci"; + method = "smc"; + cpu_suspend = <0x84000001>; + cpu_off = <0x84000002>; + cpu_on = <0x84000003>; + }; + + gic: interrupt-controller@c0001000 { + #interrupt-cells = <3>; + compatible = "arm,gic-400"; + interrupt-controller; + reg = <0x0 0xc0001000 0x1000>, + <0x0 0xc0002000 0x2000>, + <0x0 0xc0004000 0x2000>, + <0x0 0xc0006000 0x2000>; + }; + + pmu { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, + <&cpu1>, + <&cpu2>, + <&cpu3>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(0x0f) | + IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_RAW(0x0f) | + IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_RAW(0x0f) | + IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_RAW(0x0f) | + IRQ_TYPE_LEVEL_LOW)>; + }; + + clk_bus: clk_bus { + #clock-cells = <0>; + + compatible = "fixed-clock"; + clock-frequency = <198000000>; + clock-output-names = "BUSCLK"; + }; + + soc { + #address-cells = <2>; + #size-cells = <1>; + + compatible = "simple-bus"; + interrupt-parent = <&gic>; + ranges; + + eth0: ethernet@c3700000 { + compatible = "cdns,gem"; + reg = <0x0 0xc3700000 0x1000>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_bus>, <&clk_bus>; + clock-names = "hclk", "pclk"; + phy-mode = "rmii"; + /* Filled in by boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + }; + + amba { + #address-cells = <2>; + #size-cells = <1>; + #interrupts-cells = <3>; + + compatible = "simple-bus"; + interrupt-parent = <&gic>; + ranges; + + timers: timer@fd100000 { + compatible = "arm,sp804"; + reg = <0x0 0xfd100000 0x1000>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + }; + wdog: watchdog@fd200000 { + compatible = "arm,sp805", "arm,primecell"; + reg = <0x0 0xfd200000 0x1000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + }; + uart0: serial@fe000000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0 0xfe000000 0x1000>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + uart1: serial@fe100000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0 0xfe100000 0x1000>; + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + uart2: serial@fe200000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0 0xfe200000 0x1000>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + spi0: ssp@fe800000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x0 0xfe800000 0x1000>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + }; + spi1: ssp@fe900000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x0 0xfe900000 0x1000>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + }; + dmac0: dma@c1128000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xc1128000 0x1000>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + }; + gpio0: gpio@fd400000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd400000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + gpio1: gpio@fd410000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd410000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + gpio2: gpio@fd420000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd420000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + gpio3: gpio@fd430000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd430000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + }; + gpio4: gpio@fd440000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd440000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + gpio5: gpio@fd450000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd450000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + gpio6: gpio@fd460000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd460000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + gpio7: gpio@fd470000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd470000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + gpio8: gpio@fd480000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd480000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + gpio9: gpio@fd490000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd490000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + gpio10: gpio@fd4a0000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd4a0000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + gpio11: gpio@fd4b0000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd4b0000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + }; + gpio12: gpio@fd4c0000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd4c0000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + gpio13: gpio@fd4d0000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd4d0000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + gpio14: gpio@fd4e0000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd4e0000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + gpio15: gpio@fd4f0000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd4f0000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + gpio16: gpio@fd500000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd500000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + status="disabled"; + }; + gpio17: gpio@fd510000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x0 0xfd510000 0x1000>; + clocks = <&clk_bus>; + clock-names = "apb_pclk"; + }; + }; +}; diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi index 9e2efb882983..eb29280962d7 100644 --- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi @@ -105,6 +105,41 @@ status = "disabled"; }; + nb_perih_clk: nb-periph-clk@13000{ + compatible = "marvell,armada-3700-periph-clock-nb"; + reg = <0x13000 0x100>; + clocks = <&tbg 0>, <&tbg 1>, <&tbg 2>, + <&tbg 3>, <&xtalclk>; + #clock-cells = <1>; + }; + + sb_perih_clk: sb-periph-clk@18000{ + compatible = "marvell,armada-3700-periph-clock-sb"; + reg = <0x18000 0x100>; + clocks = <&tbg 0>, <&tbg 1>, <&tbg 2>, + <&tbg 3>, <&xtalclk>; + #clock-cells = <1>; + }; + + tbg: tbg@13200 { + compatible = "marvell,armada-3700-tbg-clock"; + reg = <0x13200 0x100>; + clocks = <&xtalclk>; + #clock-cells = <1>; + }; + + gpio1: gpio@13800 { + compatible = "marvell,mvebu-gpio-3700", + "syscon", "simple-mfd"; + reg = <0x13800 0x500>; + + xtalclk: xtal-clk { + compatible = "marvell,armada-3700-xtal-clock"; + clock-output-names = "xtal"; + #clock-cells = <0>; + }; + }; + usb3: usb@58000 { compatible = "marvell,armada3700-xhci", "generic-xhci"; diff --git a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi index 20d256b32670..eab1a42fb934 100644 --- a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi @@ -141,7 +141,7 @@ }; xor@400000 { - compatible = "marvell,mv-xor-v2"; + compatible = "marvell,armada-7k-xor", "marvell,xor-v2"; reg = <0x400000 0x1000>, <0x410000 0x1000>; msi-parent = <&gic_v2m0>; @@ -149,7 +149,7 @@ }; xor@420000 { - compatible = "marvell,mv-xor-v2"; + compatible = "marvell,armada-7k-xor", "marvell,xor-v2"; reg = <0x420000 0x1000>, <0x430000 0x1000>; msi-parent = <&gic_v2m0>; @@ -157,7 +157,7 @@ }; xor@440000 { - compatible = "marvell,mv-xor-v2"; + compatible = "marvell,armada-7k-xor", "marvell,xor-v2"; reg = <0x440000 0x1000>, <0x450000 0x1000>; msi-parent = <&gic_v2m0>; @@ -165,7 +165,7 @@ }; xor@460000 { - compatible = "marvell,mv-xor-v2"; + compatible = "marvell,armada-7k-xor", "marvell,xor-v2"; reg = <0x460000 0x1000>, <0x470000 0x1000>; msi-parent = <&gic_v2m0>; diff --git a/arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi index 367138bae3e0..da31bbbbb59e 100644 --- a/arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi @@ -107,6 +107,24 @@ status = "disabled"; }; + cpm_xor0: xor@6a0000 { + compatible = "marvell,armada-7k-xor", "marvell,xor-v2"; + reg = <0x6a0000 0x1000>, + <0x6b0000 0x1000>; + dma-coherent; + msi-parent = <&gic_v2m0>; + clocks = <&cpm_syscon0 1 8>; + }; + + cpm_xor1: xor@6c0000 { + compatible = "marvell,armada-7k-xor", "marvell,xor-v2"; + reg = <0x6c0000 0x1000>, + <0x6d0000 0x1000>; + dma-coherent; + msi-parent = <&gic_v2m0>; + clocks = <&cpm_syscon0 1 7>; + }; + cpm_spi0: spi@700600 { compatible = "marvell,armada-380-spi"; reg = <0x700600 0x50>; diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile index e0a4bff2fc17..9fbfd3238469 100644 --- a/arch/arm64/boot/dts/mediatek/Makefile +++ b/arch/arm64/boot/dts/mediatek/Makefile @@ -1,3 +1,4 @@ +dtb-$(CONFIG_ARCH_MEDIATEK) += mt6755-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt6795-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb diff --git a/arch/arm64/boot/dts/mediatek/mt6755-evb.dts b/arch/arm64/boot/dts/mediatek/mt6755-evb.dts new file mode 100644 index 000000000000..c568d49235af --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt6755-evb.dts @@ -0,0 +1,38 @@ +/* + * Copyright (c) 2016 MediaTek Inc. + * Author: Mars.C <mars.cheng@mediatek.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +/dts-v1/; +#include "mt6755.dtsi" + +/ { + model = "MediaTek MT6755 EVB"; + compatible = "mediatek,mt6755-evb", "mediatek,mt6755"; + + aliases { + serial0 = &uart0; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0 0x40000000 0 0x1e800000>; + }; + + chosen { + stdout-path = "serial0:921600n8"; + }; +}; + +&uart0 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt6755.dtsi b/arch/arm64/boot/dts/mediatek/mt6755.dtsi new file mode 100644 index 000000000000..01ba77669717 --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt6755.dtsi @@ -0,0 +1,145 @@ +/* + * Copyright (c) 2016 MediaTek Inc. + * Author: Mars.C <mars.cheng@mediatek.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> + +/ { + compatible = "mediatek,mt6755"; + interrupt-parent = <&sysirq>; + #address-cells = <2>; + #size-cells = <2>; + + psci { + compatible = "arm,psci-0.2"; + method = "smc"; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x000>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x001>; + }; + + cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x002>; + }; + + cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x003>; + }; + + cpu4: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x100>; + }; + + cpu5: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x101>; + }; + + cpu6: cpu@102 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x102>; + }; + + cpu7: cpu@103 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x103>; + }; + }; + + uart_clk: dummy26m { + compatible = "fixed-clock"; + clock-frequency = <26000000>; + #clock-cells = <0>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupt-parent = <&gic>; + interrupts = <GIC_PPI 13 + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; + }; + + sysirq: intpol-controller@10200620 { + compatible = "mediatek,mt6755-sysirq", + "mediatek,mt6577-sysirq"; + interrupt-controller; + #interrupt-cells = <3>; + interrupt-parent = <&gic>; + reg = <0 0x10200620 0 0x20>; + }; + + gic: interrupt-controller@10231000 { + compatible = "arm,gic-400"; + #interrupt-cells = <3>; + interrupt-parent = <&gic>; + interrupt-controller; + reg = <0 0x10231000 0 0x1000>, + <0 0x10232000 0 0x2000>, + <0 0x10234000 0 0x2000>, + <0 0x10236000 0 0x2000>; + }; + + uart0: serial@11002000 { + compatible = "mediatek,mt6755-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11002000 0 0x400>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>; + clocks = <&uart_clk>; + status = "disabled"; + }; + + uart1: serial@11003000 { + compatible = "mediatek,mt6755-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11003000 0 0x400>; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_LOW>; + clocks = <&uart_clk>; + status = "disabled"; + }; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi index 77b8c4e388ca..10f638f4e7d8 100644 --- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi @@ -26,6 +26,23 @@ #address-cells = <2>; #size-cells = <2>; + aliases { + ovl0 = &ovl0; + ovl1 = &ovl1; + rdma0 = &rdma0; + rdma1 = &rdma1; + rdma2 = &rdma2; + wdma0 = &wdma0; + wdma1 = &wdma1; + color0 = &color0; + color1 = &color1; + split0 = &split0; + split1 = &split1; + dpi0 = &dpi0; + dsi0 = &dsi0; + dsi1 = &dsi1; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -366,6 +383,26 @@ #clock-cells = <1>; }; + mipi_tx0: mipi-dphy@10215000 { + compatible = "mediatek,mt8173-mipi-tx"; + reg = <0 0x10215000 0 0x1000>; + clocks = <&clk26m>; + clock-output-names = "mipi_tx0_pll"; + #clock-cells = <0>; + #phy-cells = <0>; + status = "disabled"; + }; + + mipi_tx1: mipi-dphy@10216000 { + compatible = "mediatek,mt8173-mipi-tx"; + reg = <0 0x10216000 0 0x1000>; + clocks = <&clk26m>; + clock-output-names = "mipi_tx1_pll"; + #clock-cells = <0>; + #phy-cells = <0>; + status = "disabled"; + }; + gic: interrupt-controller@10220000 { compatible = "arm,gic-400"; #interrupt-cells = <3>; @@ -675,9 +712,181 @@ mmsys: clock-controller@14000000 { compatible = "mediatek,mt8173-mmsys", "syscon"; reg = <0 0x14000000 0 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; #clock-cells = <1>; }; + ovl0: ovl@1400c000 { + compatible = "mediatek,mt8173-disp-ovl"; + reg = <0 0x1400c000 0 0x1000>; + interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OVL0>; + iommus = <&iommu M4U_PORT_DISP_OVL0>; + mediatek,larb = <&larb0>; + }; + + ovl1: ovl@1400d000 { + compatible = "mediatek,mt8173-disp-ovl"; + reg = <0 0x1400d000 0 0x1000>; + interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OVL1>; + iommus = <&iommu M4U_PORT_DISP_OVL1>; + mediatek,larb = <&larb4>; + }; + + rdma0: rdma@1400e000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x1400e000 0 0x1000>; + interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA0>; + iommus = <&iommu M4U_PORT_DISP_RDMA0>; + mediatek,larb = <&larb0>; + }; + + rdma1: rdma@1400f000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x1400f000 0 0x1000>; + interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA1>; + iommus = <&iommu M4U_PORT_DISP_RDMA1>; + mediatek,larb = <&larb4>; + }; + + rdma2: rdma@14010000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x14010000 0 0x1000>; + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA2>; + iommus = <&iommu M4U_PORT_DISP_RDMA2>; + mediatek,larb = <&larb4>; + }; + + wdma0: wdma@14011000 { + compatible = "mediatek,mt8173-disp-wdma"; + reg = <0 0x14011000 0 0x1000>; + interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_WDMA0>; + iommus = <&iommu M4U_PORT_DISP_WDMA0>; + mediatek,larb = <&larb0>; + }; + + wdma1: wdma@14012000 { + compatible = "mediatek,mt8173-disp-wdma"; + reg = <0 0x14012000 0 0x1000>; + interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_WDMA1>; + iommus = <&iommu M4U_PORT_DISP_WDMA1>; + mediatek,larb = <&larb4>; + }; + + color0: color@14013000 { + compatible = "mediatek,mt8173-disp-color"; + reg = <0 0x14013000 0 0x1000>; + interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_COLOR0>; + }; + + color1: color@14014000 { + compatible = "mediatek,mt8173-disp-color"; + reg = <0 0x14014000 0 0x1000>; + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_COLOR1>; + }; + + aal@14015000 { + compatible = "mediatek,mt8173-disp-aal"; + reg = <0 0x14015000 0 0x1000>; + interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_AAL>; + }; + + gamma@14016000 { + compatible = "mediatek,mt8173-disp-gamma"; + reg = <0 0x14016000 0 0x1000>; + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_GAMMA>; + }; + + merge@14017000 { + compatible = "mediatek,mt8173-disp-merge"; + reg = <0 0x14017000 0 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_MERGE>; + }; + + split0: split@14018000 { + compatible = "mediatek,mt8173-disp-split"; + reg = <0 0x14018000 0 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_SPLIT0>; + }; + + split1: split@14019000 { + compatible = "mediatek,mt8173-disp-split"; + reg = <0 0x14019000 0 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_SPLIT1>; + }; + + ufoe@1401a000 { + compatible = "mediatek,mt8173-disp-ufoe"; + reg = <0 0x1401a000 0 0x1000>; + interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_UFOE>; + }; + + dsi0: dsi@1401b000 { + compatible = "mediatek,mt8173-dsi"; + reg = <0 0x1401b000 0 0x1000>; + interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DSI0_ENGINE>, + <&mmsys CLK_MM_DSI0_DIGITAL>, + <&mipi_tx0>; + clock-names = "engine", "digital", "hs"; + phys = <&mipi_tx0>; + phy-names = "dphy"; + status = "disabled"; + }; + + dsi1: dsi@1401c000 { + compatible = "mediatek,mt8173-dsi"; + reg = <0 0x1401c000 0 0x1000>; + interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DSI1_ENGINE>, + <&mmsys CLK_MM_DSI1_DIGITAL>, + <&mipi_tx1>; + clock-names = "engine", "digital", "hs"; + phy = <&mipi_tx1>; + phy-names = "dphy"; + status = "disabled"; + }; + + dpi0: dpi@1401d000 { + compatible = "mediatek,mt8173-dpi"; + reg = <0 0x1401d000 0 0x1000>; + interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DPI_PIXEL>, + <&mmsys CLK_MM_DPI_ENGINE>, + <&apmixedsys CLK_APMIXED_TVDPLL>; + clock-names = "pixel", "engine", "pll"; + status = "disabled"; + }; + pwm0: pwm@1401e000 { compatible = "mediatek,mt8173-disp-pwm", "mediatek,mt6595-disp-pwm"; @@ -700,6 +909,14 @@ status = "disabled"; }; + mutex: mutex@14020000 { + compatible = "mediatek,mt8173-disp-mutex"; + reg = <0 0x14020000 0 0x1000>; + interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_MUTEX_32K>; + }; + larb0: larb@14021000 { compatible = "mediatek,mt8173-smi-larb"; reg = <0 0x14021000 0 0x1000>; @@ -719,6 +936,12 @@ clock-names = "apb", "smi"; }; + od@14023000 { + compatible = "mediatek,mt8173-disp-od"; + reg = <0 0x14023000 0 0x1000>; + clocks = <&mmsys CLK_MM_DISP_OD>; + }; + larb4: larb@14027000 { compatible = "mediatek,mt8173-smi-larb"; reg = <0 0x14027000 0 0x1000>; diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p2180.dtsi b/arch/arm64/boot/dts/nvidia/tegra210-p2180.dtsi index 316c92c03821..5fda583351d7 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210-p2180.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra210-p2180.dtsi @@ -1,3 +1,5 @@ +#include <dt-bindings/mfd/max77620.h> + #include "tegra210.dtsi" / { @@ -5,10 +7,15 @@ compatible = "nvidia,p2180", "nvidia,tegra210"; aliases { + rtc0 = "/i2c@7000d000/pmic@3c"; rtc1 = "/rtc@7000e000"; serial0 = &uarta; }; + chosen { + stdout-path = "serial0:115200n8"; + }; + memory { device_type = "memory"; reg = <0x0 0x80000000 0x1 0x0>; @@ -19,6 +26,248 @@ status = "okay"; }; + i2c@7000d000 { + status = "okay"; + clock-frequency = <400000>; + + pmic: pmic@3c { + compatible = "maxim,max77620"; + reg = <0x3c>; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; + + #interrupt-cells = <2>; + interrupt-controller; + + #gpio-cells = <2>; + gpio-controller; + + pinctrl-names = "default"; + pinctrl-0 = <&max77620_default>; + + max77620_default: pinmux { + gpio0 { + pins = "gpio0"; + function = "gpio"; + }; + + gpio1 { + pins = "gpio1"; + function = "fps-out"; + drive-push-pull = <1>; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + maxim,active-fps-power-up-slot = <7>; + maxim,active-fps-power-down-slot = <0>; + }; + + gpio2_3 { + pins = "gpio2", "gpio3"; + function = "fps-out"; + drive-open-drain = <1>; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + }; + + gpio4 { + pins = "gpio4"; + function = "32k-out1"; + }; + + gpio5_6_7 { + pins = "gpio5", "gpio6", "gpio7"; + function = "gpio"; + drive-push-pull = <1>; + }; + }; + + fps { + fps0 { + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>; + maxim,suspend-fps-time-period-us = <1280>; + }; + + fps1 { + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>; + maxim,suspend-fps-time-period-us = <1280>; + }; + + fps2 { + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>; + }; + }; + + regulators { + in-ldo0-1-supply = <&vdd_pre>; + in-ldo7-8-supply = <&vdd_pre>; + in-sd3-supply = <&vdd_5v0_sys>; + + vdd_soc: sd0 { + regulator-name = "VDD_SOC"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + regulator-boot-on; + + regulator-enable-ramp-delay = <146>; + regulator-ramp-delay = <27500>; + + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + + vdd_ddr: sd1 { + regulator-name = "VDD_DDR_1V1_PMIC"; + regulator-always-on; + regulator-boot-on; + + regulator-enable-ramp-delay = <130>; + regulator-ramp-delay = <27500>; + + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + }; + + vdd_pre: sd2 { + regulator-name = "VDD_PRE_REG_1V35"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + + regulator-enable-ramp-delay = <176>; + regulator-ramp-delay = <27500>; + + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + + vdd_1v8: sd3 { + regulator-name = "VDD_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + + regulator-enable-ramp-delay = <242>; + regulator-ramp-delay = <27500>; + + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + }; + + vdd_sys_1v2: ldo0 { + regulator-name = "AVDD_SYS_1V2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + + regulator-enable-ramp-delay = <26>; + regulator-ramp-delay = <100000>; + + maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>; + }; + + vdd_pex_1v05: ldo1 { + regulator-name = "VDD_PEX_1V05"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + + regulator-enable-ramp-delay = <22>; + regulator-ramp-delay = <100000>; + + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + + vddio_sdmmc: ldo2 { + regulator-name = "VDDIO_SDMMC"; + /* + * Technically this supply should have + * a supported range from 1.8 - 3.3 V. + * However, that would cause the SDHCI + * driver to request 2.7 V upon access + * and that in turn will cause traffic + * to be broken. Leave it at 3.3 V for + * now. + */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + + regulator-enable-ramp-delay = <62>; + regulator-ramp-delay = <100000>; + + maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>; + }; + + vdd_cam_hv: ldo3 { + regulator-name = "VDD_CAM_HV"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + + regulator-enable-ramp-delay = <50>; + regulator-ramp-delay = <100000>; + + maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>; + }; + + vdd_rtc: ldo4 { + regulator-name = "VDD_RTC"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <850000>; + regulator-always-on; + regulator-boot-on; + + regulator-enable-ramp-delay = <22>; + regulator-ramp-delay = <100000>; + + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + }; + + vdd_ts_hv: ldo5 { + regulator-name = "VDD_TS_HV"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + regulator-enable-ramp-delay = <62>; + regulator-ramp-delay = <100000>; + + maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>; + }; + + vdd_ts: ldo6 { + regulator-name = "VDD_TS_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-enable-ramp-delay = <36>; + regulator-ramp-delay = <100000>; + + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + maxim,active-fps-power-up-slot = <7>; + maxim,active-fps-power-down-slot = <0>; + }; + + avdd_1v05_pll: ldo7 { + regulator-name = "AVDD_1V05_PLL"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + regulator-boot-on; + + regulator-enable-ramp-delay = <24>; + regulator-ramp-delay = <100000>; + + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + + avdd_1v05: ldo8 { + regulator-name = "AVDD_SATA_HDMI_DP_1V05"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + + regulator-enable-ramp-delay = <22>; + regulator-ramp-delay = <100000>; + + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + }; + }; + }; + pmc@7000e400 { nvidia,invert-interrupt; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts b/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts index 683b339a980c..983775e637a4 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts +++ b/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts @@ -6,4 +6,49 @@ / { model = "NVIDIA Jetson TX1 Developer Kit"; compatible = "nvidia,p2371-2180", "nvidia,tegra210"; + + host1x@50000000 { + dsi@54300000 { + status = "okay"; + + avdd-dsi-csi-supply = <&vdd_dsi_csi>; + + panel@0 { + compatible = "auo,b080uan01"; + reg = <0>; + + enable-gpios = <&gpio TEGRA_GPIO(V, 2) + GPIO_ACTIVE_HIGH>; + power-supply = <&vdd_5v0_io>; + backlight = <&backlight>; + }; + }; + }; + + i2c@7000c400 { + backlight: backlight@2c { + compatible = "ti,lp8557"; + reg = <0x2c>; + + dev-ctrl = /bits/ 8 <0x80>; + init-brt = /bits/ 8 <0xff>; + + pwm-period = <29334>; + + pwms = <&pwm 0 29334>; + pwm-names = "lp8557"; + + /* 3 LED string */ + rom_14h { + rom-addr = /bits/ 8 <0x14>; + rom-val = /bits/ 8 <0x87>; + }; + + /* boost frequency 1 MHz */ + rom_13h { + rom-addr = /bits/ 8 <0x13>; + rom-val = /bits/ 8 <0x01>; + }; + }; + }; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi b/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi index a2480c0c7e72..e5fc67bf46c2 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi @@ -4,6 +4,24 @@ model = "NVIDIA Tegra210 P2597 I/O board"; compatible = "nvidia,p2597", "nvidia,tegra210"; + host1x@50000000 { + dpaux@54040000 { + status = "okay"; + }; + + sor@54580000 { + status = "okay"; + + avdd-io-supply = <&avdd_1v05>; + vdd-pll-supply = <&vdd_1v8>; + hdmi-supply = <&vdd_hdmi>; + + nvidia,ddc-i2c-bus = <&hdmi_ddc>; + nvidia,hpd-gpio = <&gpio TEGRA_GPIO(CC, 1) + GPIO_ACTIVE_LOW>; + }; + }; + pinmux: pinmux@700008d4 { pinctrl-names = "boot"; pinctrl-0 = <&state_boot>; @@ -1261,6 +1279,169 @@ }; }; + pwm@7000a000 { + status = "okay"; + }; + + i2c@7000c400 { + status = "okay"; + clock-frequency = <100000>; + + exp1: gpio@74 { + compatible = "ti,tca9539"; + reg = <0x74>; + + #gpio-cells = <2>; + gpio-controller; + }; + }; + + /* HDMI DDC */ + hdmi_ddc: i2c@7000c700 { + status = "okay"; + clock-frequency = <100000>; + }; + + usb@70090000 { + phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>, + <&{/padctl@7009f000/pads/usb2/lanes/usb2-1}>, + <&{/padctl@7009f000/pads/usb2/lanes/usb2-2}>, + <&{/padctl@7009f000/pads/usb2/lanes/usb2-3}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-6}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-5}>; + phy-names = "usb2-0", "usb2-1", "usb2-2", "usb2-3", "usb3-0", + "usb3-1"; + + dvddio-pex-supply = <&vdd_pex_1v05>; + hvddio-pex-supply = <&vdd_1v8>; + avdd-usb-supply = <&vdd_3v3_sys>; + /* XXX what are these? */ + avdd-pll-utmip-supply = <&vdd_1v8>; + avdd-pll-uerefe-supply = <&vdd_pex_1v05>; + dvdd-usb-ss-pll-supply = <&vdd_pex_1v05>; + hvdd-usb-ss-pll-e-supply = <&vdd_1v8>; + + status = "okay"; + }; + + padctl@7009f000 { + status = "okay"; + + pads { + usb2 { + status = "okay"; + + lanes { + usb2-0 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-1 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-2 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-3 { + nvidia,function = "xusb"; + status = "okay"; + }; + }; + }; + + pcie { + status = "okay"; + + lanes { + pcie-0 { + nvidia,function = "pcie-x1"; + status = "okay"; + }; + + pcie-1 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-2 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-3 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-4 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-5 { + nvidia,function = "usb3-ss"; + status = "okay"; + }; + + pcie-6 { + nvidia,function = "usb3-ss"; + status = "okay"; + }; + }; + }; + + sata { + status = "okay"; + + lanes { + sata-0 { + nvidia,function = "sata"; + status = "okay"; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "okay"; + mode = "otg"; + }; + + usb2-1 { + status = "okay"; + vbus-supply = <&vdd_5v0_rtl>; + mode = "host"; + }; + + usb2-2 { + status = "okay"; + vbus-supply = <&vdd_usb_vbus>; + mode = "host"; + }; + + usb2-3 { + status = "okay"; + mode = "host"; + }; + + usb3-0 { + nvidia,usb2-companion = <1>; + status = "okay"; + }; + + usb3-1 { + nvidia,usb2-companion = <2>; + status = "okay"; + }; + }; + }; + /* MMC/SD */ sdhci@700b0000 { status = "okay"; @@ -1268,6 +1449,144 @@ no-1-8-v; cd-gpios = <&gpio TEGRA_GPIO(Z, 1) GPIO_ACTIVE_LOW>; + + vqmmc-supply = <&vddio_sdmmc>; + vmmc-supply = <&vdd_3v3_sd>; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + vdd_sys_mux: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "VDD_SYS_MUX"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_5v0_sys: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "VDD_5V0_SYS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + gpio = <&pmic 1 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_sys_mux>; + }; + + vdd_3v3_sys: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "VDD_3V3_SYS"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + gpio = <&pmic 3 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_sys_mux>; + + regulator-enable-ramp-delay = <160>; + regulator-disable-ramp-delay = <10000>; + }; + + vdd_5v0_io: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "VDD_5V0_IO_SYS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_3v3_sd: regulator@4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "VDD_3V3_SD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio TEGRA_GPIO(Z, 4) GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_3v3_sys>; + + regulator-enable-ramp-delay = <472>; + regulator-disable-ramp-delay = <4880>; + }; + + vdd_dsi_csi: regulator@5 { + compatible = "regulator-fixed"; + reg = <5>; + regulator-name = "AVDD_DSI_CSI_1V2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + vin-supply = <&vdd_sys_1v2>; + }; + + vdd_3v3_dis: regulator@6 { + compatible = "regulator-fixed"; + reg = <6>; + regulator-name = "VDD_DIS_3V3_LCD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + gpio = <&exp1 3 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_3v3_sys>; + }; + + vdd_1v8_dis: regulator@7 { + compatible = "regulator-fixed"; + reg = <7>; + regulator-name = "VDD_LCD_1V8_DIS"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + gpio = <&exp1 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_1v8>; + }; + + vdd_5v0_rtl: regulator@8 { + compatible = "regulator-fixed"; + reg = <8>; + regulator-name = "RTL_5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio TEGRA_GPIO(H, 1) GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_5v0_sys>; + }; + + vdd_usb_vbus: regulator@9 { + compatible = "regulator-fixed"; + reg = <9>; + regulator-name = "USB_VBUS_EN1"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio TEGRA_GPIO(CC, 5) GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_5v0_sys>; + }; + + vdd_hdmi: regulator@10 { + compatible = "regulator-fixed"; + reg = <10>; + regulator-name = "VDD_HDMI_5V0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&exp1 12 GPIO_ACTIVE_LOW>; + enable-active-high; + vin-supply = <&vdd_5v0_sys>; + }; }; gpio-keys { diff --git a/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts b/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts index 4d89f4e02d98..431266a48e9c 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts +++ b/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts @@ -1,6 +1,7 @@ /dts-v1/; #include <dt-bindings/input/input.h> +#include <dt-bindings/mfd/max77620.h> #include <dt-bindings/pinctrl/pinctrl-tegra.h> #include "tegra210.dtsi" @@ -1327,6 +1328,234 @@ }; }; + i2c@7000d000 { + status = "okay"; + clock-frequency = <1000000>; + + max77620: max77620@3c { + compatible = "maxim,max77620"; + reg = <0x3c>; + interrupts = <0 86 IRQ_TYPE_NONE>; + + #interrupt-cells = <2>; + interrupt-controller; + + gpio-controller; + #gpio-cells = <2>; + + pinctrl-names = "default"; + pinctrl-0 = <&max77620_default>; + + max77620_default: pinmux@0 { + pin_gpio { + pins = "gpio0", "gpio1", "gpio2", "gpio7"; + function = "gpio"; + }; + + /* + * GPIO3 is used to en_pp3300, and it is part of power + * sequence, So it must be sequenced up (automatically + * set by OTP) and down properly. + */ + pin_gpio3 { + pins = "gpio3"; + function = "fps-out"; + drive-open-drain = <1>; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + maxim,active-fps-power-up-slot = <4>; + maxim,active-fps-power-down-slot = <2>; + }; + + pin_gpio5_6 { + pins = "gpio5", "gpio6"; + function = "gpio"; + drive-push-pull = <1>; + }; + + pin_32k { + pins = "gpio4"; + function = "32k-out1"; + }; + }; + + fps { + fps0 { + maxim,shutdown-fps-time-period-us = <5120>; + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>; + }; + + fps1 { + maxim,shutdown-fps-time-period-us = <5120>; + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>; + maxim,device-state-on-disabled-event = <MAX77620_FPS_INACTIVE_STATE_SLEEP>; + }; + + fps2 { + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>; + }; + }; + + regulators { + in-ldo0-1-supply = <&pp1350>; + in-ldo2-supply = <&pp3300>; + in-ldo3-5-supply = <&pp3300>; + in-ldo7-8-supply = <&pp1350>; + + ppvar_soc: sd0 { + regulator-name = "PPVAR_SOC"; + regulator-min-microvolt = <825000>; + regulator-max-microvolt = <1125000>; + regulator-always-on; + regulator-boot-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + maxim,active-fps-power-up-slot = <1>; + maxim,active-fps-power-down-slot = <7>; + }; + + pp1100_sd1: sd1 { + regulator-name = "PP1100"; + regulator-min-microvolt = <1125000>; + regulator-max-microvolt = <1125000>; + regulator-always-on; + regulator-boot-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + maxim,active-fps-power-up-slot = <5>; + maxim,active-fps-power-down-slot = <1>; + }; + + pp1350: sd2 { + regulator-name = "PP1350"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>; + maxim,active-fps-power-up-slot = <2>; + maxim,active-fps-power-down-slot = <5>; + }; + + pp1800: sd3 { + regulator-name = "PP1800"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + maxim,active-fps-power-up-slot = <3>; + maxim,active-fps-power-down-slot = <3>; + }; + + pp1200_avdd: ldo0 { + regulator-name = "PP1200_AVDD"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-enable-ramp-delay = <26>; + regulator-ramp-delay = <100000>; + regulator-boot-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>; + maxim,active-fps-power-up-slot = <0>; + maxim,active-fps-power-down-slot = <7>; + }; + + pp1200_rcam: ldo1 { + regulator-name = "PP1200_RCAM"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-enable-ramp-delay = <22>; + regulator-ramp-delay = <100000>; + maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>; + maxim,active-fps-power-up-slot = <0>; + maxim,active-fps-power-down-slot = <7>; + }; + + pp_ldo2: ldo2 { + regulator-name = "PP_LDO2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <62>; + regulator-ramp-delay = <11000>; + regulator-always-on; + regulator-boot-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>; + maxim,active-fps-power-up-slot = <0>; + maxim,active-fps-power-down-slot = <7>; + }; + + pp2800l_rcam: ldo3 { + regulator-name = "PP2800L_RCAM"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <50>; + regulator-ramp-delay = <100000>; + maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>; + maxim,active-fps-power-up-slot = <0>; + maxim,active-fps-power-down-slot = <7>; + }; + + pp100_soc_rtc: ldo4 { + regulator-name = "PP1100_SOC_RTC"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <850000>; + regulator-enable-ramp-delay = <22>; + regulator-ramp-delay = <100000>; + regulator-always-on; /* Check this */ + regulator-boot-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + maxim,active-fps-power-up-slot = <1>; + maxim,active-fps-power-down-slot = <7>; + }; + + pp2800l_fcam: ldo5 { + regulator-name = "PP2800L_FCAM"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <62>; + regulator-ramp-delay = <100000>; + maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>; + maxim,active-fps-power-up-slot = <0>; + maxim,active-fps-power-down-slot = <7>; + }; + + ldo6 { + /* Unused. */ + regulator-name = "PP_LDO6"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <36>; + regulator-ramp-delay = <100000>; + maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>; + maxim,active-fps-power-up-slot = <0>; + maxim,active-fps-power-down-slot = <7>; + }; + + pp1050_avdd: ldo7 { + regulator-name = "PP1050_AVDD"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-enable-ramp-delay = <24>; + regulator-ramp-delay = <100000>; + regulator-always-on; + regulator-boot-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + maxim,active-fps-power-up-slot = <3>; + maxim,active-fps-power-down-slot = <4>; + }; + + avddio_1v05: ldo8 { + regulator-name = "AVDDIO_1V05"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-enable-ramp-delay = <22>; + regulator-ramp-delay = <100000>; + regulator-boot-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>; + maxim,active-fps-power-up-slot = <0>; + maxim,active-fps-power-down-slot = <7>; + }; + }; + }; + }; + pmc@7000e400 { nvidia,invert-interrupt; nvidia,suspend-mode = <0>; @@ -1421,4 +1650,89 @@ compatible = "arm,psci-1.0"; method = "smc"; }; + + regulators { + compatible = "simple-bus"; + device_type = "fixed-regulators"; + #address-cells = <1>; + #size-cells = <0>; + + ppvar_sys: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "PPVAR_SYS"; + regulator-min-microvolt = <4400000>; + regulator-max-microvolt = <4400000>; + regulator-always-on; + }; + + pplcd_vdd: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "PPLCD_VDD"; + regulator-min-microvolt = <4400000>; + regulator-max-microvolt = <4400000>; + gpio = <&gpio TEGRA_GPIO(V, 4) 0>; + enable-active-high; + regulator-boot-on; + }; + + pp3000_always: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "PP3000_ALWAYS"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + pp3300: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "PP3300"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + enable-active-high; + }; + + pp5000: regulator@4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "PP5000"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + pp1800_lcdio: regulator@5 { + compatible = "regulator-fixed"; + reg = <5>; + regulator-name = "PP1800_LCDIO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio TEGRA_GPIO(V, 3) 0>; + enable-active-high; + regulator-boot-on; + }; + + pp1800_cam: regulator@6 { + compatible = "regulator-fixed"; + reg= <6>; + regulator-name = "PP1800_CAM"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio TEGRA_GPIO(K, 3) 0>; + enable-active-high; + }; + + usbc_vbus: regulator@7 { + compatible = "regulator-fixed"; + reg = <7>; + regulator-name = "USBC_VBUS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + }; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra210.dtsi b/arch/arm64/boot/dts/nvidia/tegra210.dtsi index 76fe31faa1a5..c4cfdcf60d26 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra210.dtsi @@ -35,6 +35,26 @@ resets = <&tegra_car 207>; reset-names = "dpaux"; status = "disabled"; + + state_dpaux1_aux: pinmux-aux { + groups = "dpaux-io"; + function = "aux"; + }; + + state_dpaux1_i2c: pinmux-i2c { + groups = "dpaux-io"; + function = "i2c"; + }; + + state_dpaux1_off: pinmux-off { + groups = "dpaux-io"; + function = "off"; + }; + + i2c-bus { + #address-cells = <1>; + #size-cells = <0>; + }; }; vi@54080000 { @@ -154,6 +174,10 @@ clock-names = "sor", "parent", "dp", "safe"; resets = <&tegra_car 182>; reset-names = "sor"; + pinctrl-0 = <&state_dpaux_aux>; + pinctrl-1 = <&state_dpaux_i2c>; + pinctrl-2 = <&state_dpaux_off>; + pinctrl-names = "aux", "i2c", "off"; status = "disabled"; }; @@ -162,12 +186,17 @@ reg = <0x0 0x54580000 0x0 0x00040000>; interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA210_CLK_SOR1>, + <&tegra_car TEGRA210_CLK_SOR1_SRC>, <&tegra_car TEGRA210_CLK_PLL_D2_OUT0>, <&tegra_car TEGRA210_CLK_PLL_DP>, <&tegra_car TEGRA210_CLK_SOR_SAFE>; - clock-names = "sor", "parent", "dp", "safe"; + clock-names = "sor", "source", "parent", "dp", "safe"; resets = <&tegra_car 183>; reset-names = "sor"; + pinctrl-0 = <&state_dpaux1_aux>; + pinctrl-1 = <&state_dpaux1_i2c>; + pinctrl-2 = <&state_dpaux1_off>; + pinctrl-names = "aux", "i2c", "off"; status = "disabled"; }; @@ -181,6 +210,26 @@ resets = <&tegra_car 181>; reset-names = "dpaux"; status = "disabled"; + + state_dpaux_aux: pinmux-aux { + groups = "dpaux-io"; + function = "aux"; + }; + + state_dpaux_i2c: pinmux-i2c { + groups = "dpaux-io"; + function = "i2c"; + }; + + state_dpaux_off: pinmux-off { + groups = "dpaux-io"; + function = "off"; + }; + + i2c-bus { + #address-cells = <1>; + #size-cells = <0>; + }; }; isp@54600000 { @@ -478,6 +527,9 @@ reset-names = "i2c"; dmas = <&apbdma 26>, <&apbdma 26>; dma-names = "rx", "tx"; + pinctrl-0 = <&state_dpaux1_i2c>; + pinctrl-1 = <&state_dpaux1_off>; + pinctrl-names = "default", "idle"; status = "disabled"; }; @@ -508,6 +560,9 @@ reset-names = "i2c"; dmas = <&apbdma 30>, <&apbdma 30>; dma-names = "rx", "tx"; + pinctrl-0 = <&state_dpaux_i2c>; + pinctrl-1 = <&state_dpaux_off>; + pinctrl-names = "default", "idle"; status = "disabled"; }; @@ -584,6 +639,39 @@ reg = <0x0 0x7000e400 0x0 0x400>; clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>; clock-names = "pclk", "clk32k_in"; + + powergates { + pd_audio: aud { + clocks = <&tegra_car TEGRA210_CLK_APE>, + <&tegra_car TEGRA210_CLK_APB2APE>; + resets = <&tegra_car 198>; + #power-domain-cells = <0>; + }; + + pd_xusbss: xusba { + clocks = <&tegra_car TEGRA210_CLK_XUSB_SS>; + clock-names = "xusb-ss"; + resets = <&tegra_car TEGRA210_CLK_XUSB_SS>; + reset-names = "xusb-ss"; + #power-domain-cells = <0>; + }; + + pd_xusbdev: xusbb { + clocks = <&tegra_car TEGRA210_CLK_XUSB_DEV>; + clock-names = "xusb-dev"; + resets = <&tegra_car 95>; + reset-names = "xusb-dev"; + #power-domain-cells = <0>; + }; + + pd_xusbhost: xusbc { + clocks = <&tegra_car TEGRA210_CLK_XUSB_HOST>; + clock-names = "xusb-host"; + resets = <&tegra_car TEGRA210_CLK_XUSB_HOST>; + reset-names = "xusb-host"; + #power-domain-cells = <0>; + }; + }; }; fuse@7000f800 { @@ -621,6 +709,196 @@ status = "disabled"; }; + usb@70090000 { + compatible = "nvidia,tegra210-xusb"; + reg = <0x0 0x70090000 0x0 0x8000>, + <0x0 0x70098000 0x0 0x1000>, + <0x0 0x70099000 0x0 0x1000>; + reg-names = "hcd", "fpci", "ipfs"; + + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&tegra_car TEGRA210_CLK_XUSB_HOST>, + <&tegra_car TEGRA210_CLK_XUSB_HOST_SRC>, + <&tegra_car TEGRA210_CLK_XUSB_FALCON_SRC>, + <&tegra_car TEGRA210_CLK_XUSB_SS>, + <&tegra_car TEGRA210_CLK_XUSB_SS_DIV2>, + <&tegra_car TEGRA210_CLK_XUSB_SS_SRC>, + <&tegra_car TEGRA210_CLK_XUSB_HS_SRC>, + <&tegra_car TEGRA210_CLK_XUSB_FS_SRC>, + <&tegra_car TEGRA210_CLK_PLL_U_480M>, + <&tegra_car TEGRA210_CLK_CLK_M>, + <&tegra_car TEGRA210_CLK_PLL_E>; + clock-names = "xusb_host", "xusb_host_src", + "xusb_falcon_src", "xusb_ss", + "xusb_ss_div2", "xusb_ss_src", + "xusb_hs_src", "xusb_fs_src", + "pll_u_480m", "clk_m", "pll_e"; + resets = <&tegra_car 89>, <&tegra_car 156>, + <&tegra_car 143>; + reset-names = "xusb_host", "xusb_ss", "xusb_src"; + + nvidia,xusb-padctl = <&padctl>; + + status = "disabled"; + }; + + padctl: padctl@7009f000 { + compatible = "nvidia,tegra210-xusb-padctl"; + reg = <0x0 0x7009f000 0x0 0x1000>; + resets = <&tegra_car 142>; + reset-names = "padctl"; + + status = "disabled"; + + pads { + usb2 { + clocks = <&tegra_car TEGRA210_CLK_USB2_TRK>; + clock-names = "trk"; + status = "disabled"; + + lanes { + usb2-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-2 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-3 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + hsic { + clocks = <&tegra_car TEGRA210_CLK_HSIC_TRK>; + clock-names = "trk"; + status = "disabled"; + + lanes { + hsic-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + hsic-1 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + pcie { + clocks = <&tegra_car TEGRA210_CLK_PLL_E>; + clock-names = "pll"; + resets = <&tegra_car 205>; + reset-names = "phy"; + status = "disabled"; + + lanes { + pcie-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-2 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-3 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-4 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-5 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-6 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + sata { + clocks = <&tegra_car TEGRA210_CLK_PLL_E>; + clock-names = "pll"; + resets = <&tegra_car 204>; + reset-names = "phy"; + status = "disabled"; + + lanes { + sata-0 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "disabled"; + }; + + usb2-1 { + status = "disabled"; + }; + + usb2-2 { + status = "disabled"; + }; + + usb2-3 { + status = "disabled"; + }; + + hsic-0 { + status = "disabled"; + }; + + usb3-0 { + status = "disabled"; + }; + + usb3-1 { + status = "disabled"; + }; + + usb3-2 { + status = "disabled"; + }; + + usb3-3 { + status = "disabled"; + }; + }; + }; + sdhci@700b0000 { compatible = "nvidia,tegra210-sdhci", "nvidia,tegra124-sdhci"; reg = <0x0 0x700b0000 0x0 0x200>; @@ -673,6 +951,18 @@ #nvidia,mipi-calibrate-cells = <1>; }; + aconnect@702c0000 { + compatible = "nvidia,tegra210-aconnect"; + clocks = <&tegra_car TEGRA210_CLK_APE>, + <&tegra_car TEGRA210_CLK_APB2APE>; + clock-names = "ape", "apb2ape"; + power-domains = <&pd_audio>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x702c0000 0x0 0x702c0000 0x00040000>; + status = "disabled"; + }; + spi@70410000 { compatible = "nvidia,tegra210-qspi"; reg = <0x0 0x70410000 0x0 0x1000>; diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi index 205ef89b8ca0..18639bc0a506 100644 --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi @@ -33,6 +33,10 @@ }; soc { + dma@7884000 { + status = "okay"; + }; + serial@78af000 { label = "LS-UART0"; status = "okay"; @@ -140,6 +144,18 @@ status = "okay"; }; + sdhci@07864000 { + vmmc-supply = <&pm8916_l11>; + vqmmc-supply = <&pm8916_l12>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; + + cd-gpios = <&msmgpio 38 0x1>; + status = "okay"; + }; + usb@78d9000 { extcon = <&usb_id>, <&usb_id>; status = "okay"; diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi index 96812007850e..11bdc24cfc74 100644 --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi @@ -42,13 +42,48 @@ #size-cells = <2>; ranges; - reserve_aligned@86000000 { - reg = <0x0 0x86000000 0x0 0x0300000>; + tz-apps@86000000 { + reg = <0x0 0x86000000 0x0 0x300000>; no-map; }; smem_mem: smem_region@86300000 { - reg = <0x0 0x86300000 0x0 0x0100000>; + reg = <0x0 0x86300000 0x0 0x100000>; + no-map; + }; + + hypervisor@86400000 { + reg = <0x0 0x86400000 0x0 0x100000>; + no-map; + }; + + tz@86500000 { + reg = <0x0 0x86500000 0x0 0x180000>; + no-map; + }; + + reserved@8668000 { + reg = <0x0 0x86680000 0x0 0x80000>; + no-map; + }; + + rmtfs@86700000 { + reg = <0x0 0x86700000 0x0 0xe0000>; + no-map; + }; + + rfsa@867e00000 { + reg = <0x0 0x867e0000 0x0 0x20000>; + no-map; + }; + + mpss@86800000 { + reg = <0x0 0x86800000 0x0 0x2b00000>; + no-map; + }; + + wcnss@89300000 { + reg = <0x0 0x89300000 0x0 0x600000>; no-map; }; }; @@ -62,6 +97,8 @@ compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x0>; next-level-cache = <&L2_0>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SPC>; }; CPU1: cpu@1 { @@ -69,6 +106,8 @@ compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x1>; next-level-cache = <&L2_0>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SPC>; }; CPU2: cpu@2 { @@ -76,6 +115,8 @@ compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x2>; next-level-cache = <&L2_0>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SPC>; }; CPU3: cpu@3 { @@ -83,12 +124,35 @@ compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x3>; next-level-cache = <&L2_0>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SPC>; }; L2_0: l2-cache { compatible = "cache"; cache-level = <2>; }; + + idle-states { + CPU_SPC: spc { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x40000002>; + entry-latency-us = <130>; + exit-latency-us = <150>; + min-residency-us = <2000>; + local-timer-stop; + }; + }; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <GIC_PPI 7 GIC_CPU_MASK_SIMPLE(4)>; }; timer { @@ -122,6 +186,14 @@ hwlocks = <&tcsr_mutex 3>; }; + firmware { + scm { + compatible = "qcom,scm"; + clocks = <&gcc GCC_CRYPTO_CLK>, <&gcc GCC_CRYPTO_AXI_CLK>, <&gcc GCC_CRYPTO_AHB_CLK>; + clock-names = "core", "bus", "iface"; + }; + }; + soc: soc { #address-cells = <1>; #size-cells = <1>; diff --git a/arch/arm64/boot/dts/qcom/msm8996-pins.dtsi b/arch/arm64/boot/dts/qcom/msm8996-pins.dtsi new file mode 100644 index 000000000000..659940434842 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8996-pins.dtsi @@ -0,0 +1,303 @@ +/* + * Copyright (c) 2013-2016, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +&msmgpio { + + blsp1_spi0_default: blsp1_spi0_default { + pinmux { + function = "blsp_spi1"; + pins = "gpio0", "gpio1", "gpio3"; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio2"; + }; + pinconf { + pins = "gpio0", "gpio1", "gpio3"; + drive-strength = <12>; + bias-disable; + }; + pinconf_cs { + pins = "gpio2"; + drive-strength = <16>; + bias-disable; + output-high; + }; + }; + + blsp1_spi0_sleep: blsp1_spi0_sleep { + pinmux { + function = "gpio"; + pins = "gpio0", "gpio1", "gpio2", "gpio3"; + }; + pinconf { + pins = "gpio0", "gpio1", "gpio2", "gpio3"; + drive-strength = <2>; + bias-pull-down; + }; + }; + + blsp1_i2c2_default: blsp1_i2c2_default { + pinmux { + function = "blsp_i2c3"; + pins = "gpio47", "gpio48"; + }; + pinconf { + pins = "gpio47", "gpio48"; + drive-strength = <16>; + bias-disable = <0>; + }; + }; + + blsp1_i2c2_sleep: blsp1_i2c2_sleep { + pinmux { + function = "gpio"; + pins = "gpio47", "gpio48"; + }; + pinconf { + pins = "gpio47", "gpio48"; + drive-strength = <2>; + bias-disable = <0>; + }; + }; + + blsp2_i2c0_default: blsp2_i2c0 { + pinmux { + function = "blsp_i2c7"; + pins = "gpio55", "gpio56"; + }; + pinconf { + pins = "gpio55", "gpio56"; + drive-strength = <16>; + bias-disable; + }; + }; + + blsp2_i2c0_sleep: blsp2_i2c0_sleep { + pinmux { + function = "gpio"; + pins = "gpio55", "gpio56"; + }; + pinconf { + pins = "gpio55", "gpio56"; + drive-strength = <2>; + bias-disable; + }; + }; + + blsp2_uart1_2pins_default: blsp2_uart1_2pins { + pinmux { + function = "blsp_uart8"; + pins = "gpio4", "gpio5"; + }; + pinconf { + pins = "gpio4", "gpio5"; + drive-strength = <16>; + bias-disable; + }; + }; + + blsp2_uart1_2pins_sleep: blsp2_uart1_2pins_sleep { + pinmux { + function = "gpio"; + pins = "gpio4", "gpio5"; + }; + pinconf { + pins = "gpio4", "gpio5"; + drive-strength = <2>; + bias-disable; + }; + }; + + blsp2_uart1_4pins_default: blsp2_uart1_4pins { + pinmux { + function = "blsp_uart8"; + pins = "gpio4", "gpio5", "gpio6", "gpio7"; + }; + + pinconf { + pins = "gpio4", "gpio5", "gpio6", "gpio7"; + drive-strength = <16>; + bias-disable; + }; + }; + + blsp2_uart1_4pins_sleep: blsp2_uart1_4pins_sleep { + pinmux { + function = "gpio"; + pins = "gpio4", "gpio5", "gpio6", "gpio7"; + }; + + pinconf { + pins = "gpio4", "gpiio5", "gpio6", "gpio7"; + drive-strength = <2>; + bias-disable; + }; + }; + + blsp2_i2c1_default: blsp2_i2c1 { + pinmux { + function = "blsp_i2c8"; + pins = "gpio6", "gpio7"; + }; + pinconf { + pins = "gpio6", "gpio7"; + drive-strength = <16>; + bias-disable; + }; + }; + + blsp2_i2c1_sleep: blsp2_i2c1_sleep { + pinmux { + function = "gpio"; + pins = "gpio6", "gpio7"; + }; + pinconf { + pins = "gpio6", "gpio7"; + drive-strength = <2>; + bias-disable; + }; + }; + + blsp2_uart2_2pins_default: blsp2_uart2_2pins { + pinmux { + function = "blsp_uart9"; + pins = "gpio49", "gpio50"; + }; + pinconf { + pins = "gpio49", "gpio50"; + drive-strength = <16>; + bias-disable; + }; + }; + + blsp2_uart2_2pins_sleep: blsp2_uart2_2pins_sleep { + pinmux { + function = "gpio"; + pins = "gpio49", "gpio50"; + }; + pinconf { + pins = "gpio49", "gpio50"; + drive-strength = <2>; + bias-disable; + }; + }; + + blsp2_uart2_4pins_default: blsp2_uart2_4pins { + pinmux { + function = "blsp_uart9"; + pins = "gpio49", "gpio50", "gpio51", "gpio52"; + }; + + pinconf { + pins = "gpio49", "gpio50", "gpio51", "gpio52"; + drive-strength = <16>; + bias-disable; + }; + }; + + blsp2_uart2_4pins_sleep: blsp2_uart2_4pins_sleep { + pinmux { + function = "gpio"; + pins = "gpio49", "gpio50", "gpio51", "gpio52"; + }; + + pinconf { + pins = "gpio49", "gpio50", "gpio51", "gpio52"; + drive-strength = <2>; + bias-disable; + }; + }; + + blsp2_spi5_default: blsp2_spi5_default { + pinmux { + function = "blsp_spi12"; + pins = "gpio85", "gpio86", "gpio88"; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio87"; + }; + pinconf { + pins = "gpio85", "gpio86", "gpio88"; + drive-strength = <12>; + bias-disable; + }; + pinconf_cs { + pins = "gpio87"; + drive-strength = <16>; + bias-disable; + output-high; + }; + }; + + blsp2_spi5_sleep: blsp2_spi5_sleep { + pinmux { + function = "gpio"; + pins = "gpio85", "gpio86", "gpio87", "gpio88"; + }; + pinconf { + pins = "gpio85", "gpio86", "gpio87", "gpio88"; + drive-strength = <2>; + bias-pull-down; + }; + }; + + sdc2_clk_on: sdc2_clk_on { + config { + pins = "sdc2_clk"; + bias-disable; /* NO pull */ + drive-strength = <16>; /* 16 MA */ + }; + }; + + sdc2_clk_off: sdc2_clk_off { + config { + pins = "sdc2_clk"; + bias-disable; /* NO pull */ + drive-strength = <2>; /* 2 MA */ + }; + }; + + sdc2_cmd_on: sdc2_cmd_on { + config { + pins = "sdc2_cmd"; + bias-pull-up; /* pull up */ + drive-strength = <10>; /* 10 MA */ + }; + }; + + sdc2_cmd_off: sdc2_cmd_off { + config { + pins = "sdc2_cmd"; + bias-pull-up; /* pull up */ + drive-strength = <2>; /* 2 MA */ + }; + }; + + sdc2_data_on: sdc2_data_on { + config { + pins = "sdc2_data"; + bias-pull-up; /* pull up */ + drive-strength = <10>; /* 10 MA */ + }; + }; + + sdc2_data_off: sdc2_data_off { + config { + pins = "sdc2_data"; + bias-pull-up; /* pull up */ + drive-strength = <2>; /* 2 MA */ + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi index 0506fb808c56..55ec3e8326b7 100644 --- a/arch/arm64/boot/dts/qcom/msm8996.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi @@ -151,6 +151,36 @@ reg = <0x300000 0x90000>; }; + blsp1_spi0: spi@07575000 { + compatible = "qcom,spi-qup-v2.2.1"; + reg = <0x07575000 0x600>; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_spi0_default>; + pinctrl-1 = <&blsp1_spi0_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp2_i2c0: i2c@075b5000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x075b5000 0x1000>; + interrupts = <GIC_SPI 101 0>; + clocks = <&gcc GCC_BLSP2_AHB_CLK>, + <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>; + clock-names = "iface", "core"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_i2c0_default>; + pinctrl-1 = <&blsp2_i2c0_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + blsp2_uart1: serial@75b0000 { compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; reg = <0x75b0000 0x1000>; @@ -161,7 +191,77 @@ status = "disabled"; }; - pinctrl@1010000 { + blsp2_i2c1: i2c@075b6000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x075b6000 0x1000>; + interrupts = <GIC_SPI 102 0>; + clocks = <&gcc GCC_BLSP2_AHB_CLK>, + <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>; + clock-names = "iface", "core"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_i2c1_default>; + pinctrl-1 = <&blsp2_i2c1_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp2_uart2: serial@75b1000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x075b1000 0x1000>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP2_UART3_APPS_CLK>, + <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + + blsp1_i2c2: i2c@07577000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x07577000 0x1000>; + interrupts = <GIC_SPI 97 0>; + clocks = <&gcc GCC_BLSP1_AHB_CLK>, + <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>; + clock-names = "iface", "core"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_i2c2_default>; + pinctrl-1 = <&blsp1_i2c2_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp2_spi5: spi@075ba000{ + compatible = "qcom,spi-qup-v2.2.1"; + reg = <0x075ba000 0x600>; + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP2_QUP5_SPI_APPS_CLK>, + <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "core", "iface"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_spi5_default>; + pinctrl-1 = <&blsp2_spi5_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + sdhc2: sdhci@74a4900 { + status = "disabled"; + compatible = "qcom,sdhci-msm-v4"; + reg = <0x74a4900 0x314>, <0x74a4000 0x800>; + reg-names = "hc_mem", "core_mem"; + + interrupts = <0 125 0>, <0 221 0>; + interrupt-names = "hc_irq", "pwr_irq"; + + clock-names = "iface", "core"; + clocks = <&gcc GCC_SDCC2_AHB_CLK>, + <&gcc GCC_SDCC2_APPS_CLK>; + bus-width = <4>; + }; + + msmgpio: pinctrl@1010000 { compatible = "qcom,msm8996-pinctrl"; reg = <0x01010000 0x300000>; interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; @@ -267,3 +367,4 @@ }; }; }; +#include "msm8996-pins.dtsi" diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile index 9ce1890a650e..17139f7003a6 100644 --- a/arch/arm64/boot/dts/renesas/Makefile +++ b/arch/arm64/boot/dts/renesas/Makefile @@ -1,4 +1,5 @@ dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-salvator-x.dtb +dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-x.dtb always := $(dtb-y) clean-files := *.dtb diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts index 9f561c943f6f..98f02631a0f0 100644 --- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts +++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts @@ -62,7 +62,7 @@ clock-frequency = <24576000>; }; - vcc_sdhi0: regulator@1 { + vcc_sdhi0: regulator-vcc-sdhi0 { compatible = "regulator-fixed"; regulator-name = "SDHI0 Vcc"; @@ -73,7 +73,7 @@ enable-active-high; }; - vccq_sdhi0: regulator@2 { + vccq_sdhi0: regulator-vccq-sdhi0 { compatible = "regulator-gpio"; regulator-name = "SDHI0 VccQ"; @@ -86,7 +86,7 @@ 1800000 0>; }; - vcc_sdhi3: regulator@3 { + vcc_sdhi3: regulator-vcc-sdhi3 { compatible = "regulator-fixed"; regulator-name = "SDHI3 Vcc"; @@ -97,7 +97,7 @@ enable-active-high; }; - vccq_sdhi3: regulator@4 { + vccq_sdhi3: regulator-vccq-sdhi3 { compatible = "regulator-gpio"; regulator-name = "SDHI3 VccQ"; @@ -208,6 +208,7 @@ pinctrl-0 = <&scif1_pins>; pinctrl-names = "default"; + uart-has-rtscts; status = "okay"; }; @@ -329,6 +330,11 @@ shared-pin; }; +&wdt0 { + timeout-sec = <60>; + status = "okay"; +}; + &audio_clk_a { clock-frequency = <22579200>; }; diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi index 3285a9286786..b902356873c2 100644 --- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi @@ -53,6 +53,7 @@ next-level-cache = <&L2_CA57>; enable-method = "psci"; }; + a57_2: cpu@2 { compatible = "arm,cortex-a57","arm,armv8"; reg = <0x2>; @@ -61,6 +62,7 @@ next-level-cache = <&L2_CA57>; enable-method = "psci"; }; + a57_3: cpu@3 { compatible = "arm,cortex-a57","arm,armv8"; reg = <0x3>; @@ -69,20 +71,22 @@ next-level-cache = <&L2_CA57>; enable-method = "psci"; }; - }; - L2_CA57: cache-controller@0 { - compatible = "cache"; - power-domains = <&sysc R8A7795_PD_CA57_SCU>; - cache-unified; - cache-level = <2>; - }; + L2_CA57: cache-controller@0 { + compatible = "cache"; + reg = <0>; + power-domains = <&sysc R8A7795_PD_CA57_SCU>; + cache-unified; + cache-level = <2>; + }; - L2_CA53: cache-controller@1 { - compatible = "cache"; - power-domains = <&sysc R8A7795_PD_CA53_SCU>; - cache-unified; - cache-level = <2>; + L2_CA53: cache-controller@100 { + compatible = "cache"; + reg = <0x100>; + power-domains = <&sysc R8A7795_PD_CA53_SCU>; + cache-unified; + cache-level = <2>; + }; }; extal_clk: extal { @@ -151,19 +155,27 @@ #size-cells = <2>; ranges; - gic: interrupt-controller@0xf1010000 { + gic: interrupt-controller@f1010000 { compatible = "arm,gic-400"; #interrupt-cells = <3>; #address-cells = <0>; interrupt-controller; reg = <0x0 0xf1010000 0 0x1000>, - <0x0 0xf1020000 0 0x2000>, + <0x0 0xf1020000 0 0x20000>, <0x0 0xf1040000 0 0x20000>, - <0x0 0xf1060000 0 0x2000>; + <0x0 0xf1060000 0 0x20000>; interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; }; + wdt0: watchdog@e6020000 { + compatible = "renesas,r8a7795-wdt", "renesas,rcar-gen3-wdt"; + reg = <0 0xe6020000 0 0x0c>; + clocks = <&cpg CPG_MOD 402>; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + status = "disabled"; + }; + gpio0: gpio@e6050000 { compatible = "renesas,gpio-r8a7795", "renesas,gpio-rcar"; @@ -571,6 +583,30 @@ status = "disabled"; }; + canfd: can@e66c0000 { + compatible = "renesas,r8a7795-canfd", + "renesas,rcar-gen3-canfd"; + reg = <0 0xe66c0000 0 0x8000>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 914>, + <&cpg CPG_CORE R8A7795_CLK_CANFD>, + <&can_clk>; + clock-names = "fck", "canfd", "can_clk"; + assigned-clocks = <&cpg CPG_CORE R8A7795_CLK_CANFD>; + assigned-clock-rates = <40000000>; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + status = "disabled"; + + channel0 { + status = "disabled"; + }; + + channel1 { + status = "disabled"; + }; + }; + hscif0: serial@e6540000 { compatible = "renesas,hscif-r8a7795", "renesas,rcar-gen3-hscif", @@ -749,6 +785,8 @@ interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 931>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + dmas = <&dmac1 0x91>, <&dmac1 0x90>; + dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <110>; status = "disabled"; }; @@ -761,6 +799,8 @@ interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 930>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + dmas = <&dmac1 0x93>, <&dmac1 0x92>; + dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; @@ -773,6 +813,8 @@ interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 929>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + dmas = <&dmac1 0x95>, <&dmac1 0x94>; + dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; @@ -785,6 +827,8 @@ interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 928>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + dmas = <&dmac0 0x97>, <&dmac0 0x96>; + dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <110>; status = "disabled"; }; @@ -797,6 +841,8 @@ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 927>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + dmas = <&dmac0 0x99>, <&dmac0 0x98>; + dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <110>; status = "disabled"; }; @@ -809,6 +855,8 @@ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 919>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + dmas = <&dmac0 0x9b>, <&dmac0 0x9a>; + dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <110>; status = "disabled"; }; @@ -821,6 +869,8 @@ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 918>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + dmas = <&dmac0 0x9d>, <&dmac0 0x9c>; + dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <6>; status = "disabled"; }; @@ -874,63 +924,63 @@ status = "disabled"; rcar_sound,dvc { - dvc0: dvc@0 { + dvc0: dvc-0 { dmas = <&audma0 0xbc>; dma-names = "tx"; }; - dvc1: dvc@1 { + dvc1: dvc-1 { dmas = <&audma0 0xbe>; dma-names = "tx"; }; }; rcar_sound,src { - src0: src@0 { + src0: src-0 { interrupts = <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x85>, <&audma1 0x9a>; dma-names = "rx", "tx"; }; - src1: src@1 { + src1: src-1 { interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x87>, <&audma1 0x9c>; dma-names = "rx", "tx"; }; - src2: src@2 { + src2: src-2 { interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x89>, <&audma1 0x9e>; dma-names = "rx", "tx"; }; - src3: src@3 { + src3: src-3 { interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x8b>, <&audma1 0xa0>; dma-names = "rx", "tx"; }; - src4: src@4 { + src4: src-4 { interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x8d>, <&audma1 0xb0>; dma-names = "rx", "tx"; }; - src5: src@5 { + src5: src-5 { interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x8f>, <&audma1 0xb2>; dma-names = "rx", "tx"; }; - src6: src@6 { + src6: src-6 { interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x91>, <&audma1 0xb4>; dma-names = "rx", "tx"; }; - src7: src@7 { + src7: src-7 { interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x93>, <&audma1 0xb6>; dma-names = "rx", "tx"; }; - src8: src@8 { + src8: src-8 { interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x95>, <&audma1 0xb8>; dma-names = "rx", "tx"; }; - src9: src@9 { + src9: src-9 { interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x97>, <&audma1 0xba>; dma-names = "rx", "tx"; @@ -938,52 +988,52 @@ }; rcar_sound,ssi { - ssi0: ssi@0 { + ssi0: ssi-0 { interrupts = <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi1: ssi@1 { + ssi1: ssi-1 { interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi2: ssi@2 { + ssi2: ssi-2 { interrupts = <GIC_SPI 372 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi3: ssi@3 { + ssi3: ssi-3 { interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi4: ssi@4 { + ssi4: ssi-4 { interrupts = <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi5: ssi@5 { + ssi5: ssi-5 { interrupts = <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi6: ssi@6 { + ssi6: ssi-6 { interrupts = <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi7: ssi@7 { + ssi7: ssi-7 { interrupts = <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi8: ssi@8 { + ssi8: ssi-8 { interrupts = <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>; dma-names = "rx", "tx", "rxu", "txu"; }; - ssi9: ssi@9 { + ssi9: ssi-9 { interrupts = <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>; dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>; dma-names = "rx", "tx", "rxu", "txu"; diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts new file mode 100644 index 000000000000..e72be3856d79 --- /dev/null +++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts @@ -0,0 +1,50 @@ +/* + * Device Tree Source for the Salvator-X board + * + * Copyright (C) 2016 Renesas Electronics Corp. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +/dts-v1/; +#include "r8a7796.dtsi" + +/ { + model = "Renesas Salvator-X board based on r8a7796"; + compatible = "renesas,salvator-x", "renesas,r8a7796"; + + aliases { + serial0 = &scif2; + }; + + chosen { + bootargs = "ignore_loglevel"; + stdout-path = "serial0:115200n8"; + }; + + memory@48000000 { + device_type = "memory"; + /* first 128MB is reserved for secure area. */ + reg = <0x0 0x48000000 0x0 0x78000000>; + }; +}; + +&extal_clk { + clock-frequency = <16666666>; +}; + +&scif2 { + status = "okay"; +}; + +&scif_clk { + clock-frequency = <14745600>; + status = "okay"; +}; + +&wdt0 { + timeout-sec = <60>; + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi new file mode 100644 index 000000000000..1edf82440d78 --- /dev/null +++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi @@ -0,0 +1,138 @@ +/* + * Device Tree Source for the r8a7796 SoC + * + * Copyright (C) 2016 Renesas Electronics Corp. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#include <dt-bindings/clock/r8a7796-cpg-mssr.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/power/r8a7796-sysc.h> + +/ { + compatible = "renesas,r8a7796"; + #address-cells = <2>; + #size-cells = <2>; + + psci { + compatible = "arm,psci-0.2"; + method = "smc"; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + /* 1 core only at this point */ + a57_0: cpu@0 { + compatible = "arm,cortex-a57", "arm,armv8"; + reg = <0x0>; + device_type = "cpu"; + power-domains = <&sysc R8A7796_PD_CA57_CPU0>; + next-level-cache = <&L2_CA57>; + enable-method = "psci"; + }; + + L2_CA57: cache-controller@0 { + compatible = "cache"; + reg = <0>; + power-domains = <&sysc R8A7796_PD_CA57_SCU>; + cache-unified; + cache-level = <2>; + }; + }; + + extal_clk: extal { + compatible = "fixed-clock"; + #clock-cells = <0>; + /* This value must be overridden by the board */ + clock-frequency = <0>; + }; + + extalr_clk: extalr { + compatible = "fixed-clock"; + #clock-cells = <0>; + /* This value must be overridden by the board */ + clock-frequency = <0>; + }; + + /* External SCIF clock - to be overridden by boards that provide it */ + scif_clk: scif { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + }; + + soc { + compatible = "simple-bus"; + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + gic: interrupt-controller@f1010000 { + compatible = "arm,gic-400"; + #interrupt-cells = <3>; + #address-cells = <0>; + interrupt-controller; + reg = <0x0 0xf1010000 0 0x1000>, + <0x0 0xf1020000 0 0x20000>, + <0x0 0xf1040000 0 0x20000>, + <0x0 0xf1060000 0 0x20000>; + interrupts = <GIC_PPI 9 + (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 + (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 + (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 + (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 + (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>; + }; + + wdt0: watchdog@e6020000 { + compatible = "renesas,r8a7796-wdt", + "renesas,rcar-gen3-wdt"; + reg = <0 0xe6020000 0 0x0c>; + clocks = <&cpg CPG_MOD 402>; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + status = "disabled"; + }; + + cpg: clock-controller@e6150000 { + compatible = "renesas,r8a7796-cpg-mssr"; + reg = <0 0xe6150000 0 0x1000>; + clocks = <&extal_clk>, <&extalr_clk>; + clock-names = "extal", "extalr"; + #clock-cells = <2>; + #power-domain-cells = <0>; + }; + + sysc: system-controller@e6180000 { + compatible = "renesas,r8a7796-sysc"; + reg = <0 0xe6180000 0 0x0400>; + #power-domain-cells = <1>; + }; + + scif2: serial@e6e88000 { + compatible = "renesas,scif-r8a7796", + "renesas,rcar-gen3-scif", "renesas,scif"; + reg = <0 0xe6e88000 0 64>; + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 310>, + <&cpg CPG_CORE R8A7796_CLK_S3D1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + status = "disabled"; + }; + }; +}; diff --git a/arch/arm64/boot/dts/rockchip/rk3368-r88.dts b/arch/arm64/boot/dts/rockchip/rk3368-r88.dts index b56b7205e39b..82a32e5591e2 100644 --- a/arch/arm64/boot/dts/rockchip/rk3368-r88.dts +++ b/arch/arm64/boot/dts/rockchip/rk3368-r88.dts @@ -236,6 +236,15 @@ }; }; +&io_domains { + status = "ok"; + + audio-supply = <&vcc_io>; + gpio30-supply = <&vcc_io>; + gpio1830-supply = <&vcc_io>; + wifi-supply = <&vccio_wl>; +}; + &sdio0 { assigned-clocks = <&cru SCLK_SDIO0>; assigned-clock-parents = <&cru PLL_CPLL>; @@ -329,6 +338,13 @@ }; }; +&pmu_io_domains { + status = "okay"; + + pmu-supply = <&vcc_io>; + vop-supply = <&vcc_io>; +}; + &saradc { vref-supply = <&vcc_18>; status = "okay"; diff --git a/arch/arm64/boot/dts/rockchip/rk3368.dtsi b/arch/arm64/boot/dts/rockchip/rk3368.dtsi index 8b4a7c9154e9..d02a900378e1 100644 --- a/arch/arm64/boot/dts/rockchip/rk3368.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3368.dtsi @@ -632,8 +632,13 @@ }; pmugrf: syscon@ff738000 { - compatible = "rockchip,rk3368-pmugrf", "syscon"; + compatible = "rockchip,rk3368-pmugrf", "syscon", "simple-mfd"; reg = <0x0 0xff738000 0x0 0x1000>; + + pmu_io_domains: io-domains { + compatible = "rockchip,rk3368-pmu-io-voltage-domain"; + status = "disabled"; + }; }; cru: clock-controller@ff760000 { @@ -645,8 +650,13 @@ }; grf: syscon@ff770000 { - compatible = "rockchip,rk3368-grf", "syscon"; + compatible = "rockchip,rk3368-grf", "syscon", "simple-mfd"; reg = <0x0 0xff770000 0x0 0x1000>; + + io_domains: io-domains { + compatible = "rockchip,rk3368-io-voltage-domain"; + status = "disabled"; + }; }; wdt: watchdog@ff800000 { @@ -670,7 +680,7 @@ #address-cells = <0>; reg = <0x0 0xffb71000 0x0 0x1000>, - <0x0 0xffb72000 0x0 0x1000>, + <0x0 0xffb72000 0x0 0x2000>, <0x0 0xffb74000 0x0 0x2000>, <0x0 0xffb76000 0x0 0x2000>; interrupts = <GIC_PPI 9 diff --git a/arch/arm64/boot/dts/rockchip/rk3399-evb.dts b/arch/arm64/boot/dts/rockchip/rk3399-evb.dts index 1a3eb1482050..d33aa06d46f5 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-evb.dts +++ b/arch/arm64/boot/dts/rockchip/rk3399-evb.dts @@ -77,6 +77,10 @@ }; }; +&emmc_phy { + status = "okay"; +}; + &pwm0 { status = "okay"; }; @@ -89,6 +93,14 @@ status = "okay"; }; +&sdhci { + bus-width = <8>; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + non-removable; + status = "okay"; +}; + &uart2 { status = "okay"; }; diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi index 188bbeab92b9..a6dd623a8845 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi @@ -45,6 +45,7 @@ #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/thermal/thermal.h> / { compatible = "rockchip,rk3399"; @@ -54,6 +55,15 @@ #size-cells = <2>; aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + i2c3 = &i2c3; + i2c4 = &i2c4; + i2c5 = &i2c5; + i2c6 = &i2c6; + i2c7 = &i2c7; + i2c8 = &i2c8; serial0 = &uart0; serial1 = &uart1; serial2 = &uart2; @@ -215,6 +225,22 @@ status = "disabled"; }; + sdhci: sdhci@fe330000 { + compatible = "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1"; + reg = <0x0 0xfe330000 0x0 0x10000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + arasan,soc-ctl-syscon = <&grf>; + assigned-clocks = <&cru SCLK_EMMC>; + assigned-clock-rates = <200000000>; + clocks = <&cru SCLK_EMMC>, <&cru ACLK_EMMC>; + clock-names = "clk_xin", "clk_ahb"; + clock-output-names = "emmc_cardclock"; + #clock-cells = <0>; + phys = <&emmc_phy>; + phy-names = "phy_arasan"; + status = "disabled"; + }; + usb_host0_ehci: usb@fe380000 { compatible = "generic-ehci"; reg = <0x0 0xfe380000 0x0 0x20000>; @@ -272,6 +298,96 @@ }; }; + i2c1: i2c@ff110000 { + compatible = "rockchip,rk3399-i2c"; + reg = <0x0 0xff110000 0x0 0x1000>; + assigned-clocks = <&cru SCLK_I2C1>; + assigned-clock-rates = <200000000>; + clocks = <&cru SCLK_I2C1>, <&cru PCLK_I2C1>; + clock-names = "i2c", "pclk"; + interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_xfer>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@ff120000 { + compatible = "rockchip,rk3399-i2c"; + reg = <0x0 0xff120000 0x0 0x1000>; + assigned-clocks = <&cru SCLK_I2C2>; + assigned-clock-rates = <200000000>; + clocks = <&cru SCLK_I2C2>, <&cru PCLK_I2C2>; + clock-names = "i2c", "pclk"; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_xfer>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c3: i2c@ff130000 { + compatible = "rockchip,rk3399-i2c"; + reg = <0x0 0xff130000 0x0 0x1000>; + assigned-clocks = <&cru SCLK_I2C3>; + assigned-clock-rates = <200000000>; + clocks = <&cru SCLK_I2C3>, <&cru PCLK_I2C3>; + clock-names = "i2c", "pclk"; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_xfer>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c5: i2c@ff140000 { + compatible = "rockchip,rk3399-i2c"; + reg = <0x0 0xff140000 0x0 0x1000>; + assigned-clocks = <&cru SCLK_I2C5>; + assigned-clock-rates = <200000000>; + clocks = <&cru SCLK_I2C5>, <&cru PCLK_I2C5>; + clock-names = "i2c", "pclk"; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c5_xfer>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c6: i2c@ff150000 { + compatible = "rockchip,rk3399-i2c"; + reg = <0x0 0xff150000 0x0 0x1000>; + assigned-clocks = <&cru SCLK_I2C6>; + assigned-clock-rates = <200000000>; + clocks = <&cru SCLK_I2C6>, <&cru PCLK_I2C6>; + clock-names = "i2c", "pclk"; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c6_xfer>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c7: i2c@ff160000 { + compatible = "rockchip,rk3399-i2c"; + reg = <0x0 0xff160000 0x0 0x1000>; + assigned-clocks = <&cru SCLK_I2C7>; + assigned-clock-rates = <200000000>; + clocks = <&cru SCLK_I2C7>, <&cru PCLK_I2C7>; + clock-names = "i2c", "pclk"; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c7_xfer>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + uart0: serial@ff180000 { compatible = "rockchip,rk3399-uart", "snps,dw-apb-uart"; reg = <0x0 0xff180000 0x0 0x100>; @@ -389,9 +505,105 @@ status = "disabled"; }; + thermal-zones { + cpu_thermal: cpu { + polling-delay-passive = <100>; + polling-delay = <1000>; + + thermal-sensors = <&tsadc 0>; + + trips { + cpu_alert0: cpu_alert0 { + temperature = <70000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu_alert1: cpu_alert1 { + temperature = <75000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu_crit: cpu_crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu_alert0>; + cooling-device = + <&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu_alert1>; + cooling-device = + <&cpu_l0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + gpu_thermal: gpu { + polling-delay-passive = <100>; + polling-delay = <1000>; + + thermal-sensors = <&tsadc 1>; + + trips { + gpu_alert0: gpu_alert0 { + temperature = <75000>; + hysteresis = <2000>; + type = "passive"; + }; + gpu_crit: gpu_crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&gpu_alert0>; + cooling-device = + <&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + }; + + tsadc: tsadc@ff260000 { + compatible = "rockchip,rk3399-tsadc"; + reg = <0x0 0xff260000 0x0 0x100>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + assigned-clocks = <&cru SCLK_TSADC>; + assigned-clock-rates = <750000>; + clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>; + clock-names = "tsadc", "apb_pclk"; + resets = <&cru SRST_TSADC>; + reset-names = "tsadc-apb"; + rockchip,grf = <&grf>; + rockchip,hw-tshut-temp = <95000>; + pinctrl-names = "init", "default", "sleep"; + pinctrl-0 = <&otp_gpio>; + pinctrl-1 = <&otp_out>; + pinctrl-2 = <&otp_gpio>; + #thermal-sensor-cells = <1>; + status = "disabled"; + }; + pmugrf: syscon@ff320000 { - compatible = "rockchip,rk3399-pmugrf", "syscon"; + compatible = "rockchip,rk3399-pmugrf", "syscon", "simple-mfd"; reg = <0x0 0xff320000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + pmu_io_domains: io-domains { + compatible = "rockchip,rk3399-pmu-io-voltage-domain"; + status = "disabled"; + }; }; spi3: spi@ff350000 { @@ -420,6 +632,51 @@ status = "disabled"; }; + i2c0: i2c@ff3c0000 { + compatible = "rockchip,rk3399-i2c"; + reg = <0x0 0xff3c0000 0x0 0x1000>; + assigned-clocks = <&pmucru SCLK_I2C0_PMU>; + assigned-clock-rates = <200000000>; + clocks = <&pmucru SCLK_I2C0_PMU>, <&pmucru PCLK_I2C0_PMU>; + clock-names = "i2c", "pclk"; + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_xfer>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c4: i2c@ff3d0000 { + compatible = "rockchip,rk3399-i2c"; + reg = <0x0 0xff3d0000 0x0 0x1000>; + assigned-clocks = <&pmucru SCLK_I2C4_PMU>; + assigned-clock-rates = <200000000>; + clocks = <&pmucru SCLK_I2C4_PMU>, <&pmucru PCLK_I2C4_PMU>; + clock-names = "i2c", "pclk"; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_xfer>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c8: i2c@ff3e0000 { + compatible = "rockchip,rk3399-i2c"; + reg = <0x0 0xff3e0000 0x0 0x1000>; + assigned-clocks = <&pmucru SCLK_I2C8_PMU>; + assigned-clock-rates = <200000000>; + clocks = <&pmucru SCLK_I2C8_PMU>, <&pmucru PCLK_I2C8_PMU>; + clock-names = "i2c", "pclk"; + interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c8_xfer>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + pwm0: pwm@ff420000 { compatible = "rockchip,rk3399-pwm", "rockchip,rk3288-pwm"; reg = <0x0 0xff420000 0x0 0x10>; @@ -478,11 +735,43 @@ reg = <0x0 0xff760000 0x0 0x1000>; #clock-cells = <1>; #reset-cells = <1>; + assigned-clocks = + <&cru PLL_GPLL>, <&cru PLL_CPLL>, + <&cru PLL_NPLL>, + <&cru ACLK_PERIHP>, <&cru HCLK_PERIHP>, + <&cru PCLK_PERIHP>, + <&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>, + <&cru PCLK_PERILP0>, + <&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>; + assigned-clock-rates = + <594000000>, <800000000>, + <1000000000>, + <150000000>, <75000000>, + <37500000>, + <100000000>, <100000000>, + <50000000>, + <100000000>, <50000000>; }; grf: syscon@ff770000 { - compatible = "rockchip,rk3399-grf", "syscon"; + compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd"; reg = <0x0 0xff770000 0x0 0x10000>; + #address-cells = <1>; + #size-cells = <1>; + + io_domains: io-domains { + compatible = "rockchip,rk3399-io-voltage-domain"; + status = "disabled"; + }; + + emmc_phy: phy@f780 { + compatible = "rockchip,rk3399-emmc-phy"; + reg = <0xf780 0x24>; + clocks = <&sdhci>; + clock-names = "emmcclk"; + #phy-cells = <0>; + status = "disabled"; + }; }; watchdog@ff840000 { @@ -764,6 +1053,16 @@ }; }; + sleep { + ap_pwroff: ap-pwroff { + rockchip,pins = <1 5 RK_FUNC_1 &pcfg_pull_none>; + }; + + ddrio_pwroff: ddrio-pwroff { + rockchip,pins = <0 1 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + spdif { spdif_bus: spdif-bus { rockchip,pins = @@ -889,6 +1188,16 @@ }; }; + tsadc { + otp_gpio: otp-gpio { + rockchip,pins = <1 6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + otp_out: otp-out { + rockchip,pins = <1 6 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + uart0 { uart0_xfer: uart0-xfer { rockchip,pins = diff --git a/arch/arm64/boot/dts/socionext/uniphier-ph1-ld20.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ph1-ld20.dtsi index 95328808e3c1..c223915f0907 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ph1-ld20.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-ph1-ld20.dtsi @@ -42,6 +42,8 @@ * OTHER DEALINGS IN THE SOFTWARE. */ +/memreserve/ 0x80000000 0x00000008; /* cpu-release-addr */ + / { compatible = "socionext,ph1-ld20"; #address-cells = <2>; @@ -77,7 +79,7 @@ compatible = "arm,cortex-a72", "arm,armv8"; reg = <0 0x000>; enable-method = "spin-table"; - cpu-release-addr = <0 0x80000100>; + cpu-release-addr = <0 0x80000000>; }; cpu1: cpu@1 { @@ -85,7 +87,7 @@ compatible = "arm,cortex-a72", "arm,armv8"; reg = <0 0x001>; enable-method = "spin-table"; - cpu-release-addr = <0 0x80000100>; + cpu-release-addr = <0 0x80000000>; }; cpu2: cpu@100 { @@ -93,7 +95,7 @@ compatible = "arm,cortex-a53", "arm,armv8"; reg = <0 0x100>; enable-method = "spin-table"; - cpu-release-addr = <0 0x80000100>; + cpu-release-addr = <0 0x80000000>; }; cpu3: cpu@101 { @@ -101,7 +103,7 @@ compatible = "arm,cortex-a53", "arm,armv8"; reg = <0 0x101>; enable-method = "spin-table"; - cpu-release-addr = <0 0x80000100>; + cpu-release-addr = <0 0x80000000>; }; }; @@ -264,9 +266,13 @@ reg = <0x59801000 0x400>; }; - pinctrl: pinctrl@5f801000 { - compatible = "socionext,ph1-ld20-pinctrl", "syscon"; - reg = <0x5f801000 0xe00>; + soc-glue@5f800000 { + compatible = "simple-mfd", "syscon"; + reg = <0x5f800000 0x2000>; + + pinctrl: pinctrl { + compatible = "socionext,uniphier-ld20-pinctrl"; + }; }; gic: interrupt-controller@5fe00000 { |
