diff options
Diffstat (limited to 'arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts')
| -rw-r--r-- | arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts | 184 |
1 files changed, 1 insertions, 183 deletions
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts index fbcf03f86c96..1542d836c090 100644 --- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts +++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts @@ -12,191 +12,9 @@ /dts-v1/; -#include <dt-bindings/gpio/gpio.h> -#include "armada-372x.dtsi" +#include "armada-3720-espressobin.dtsi" / { model = "Globalscale Marvell ESPRESSOBin Board"; compatible = "globalscale,espressobin", "marvell,armada3720", "marvell,armada3710"; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory@0 { - device_type = "memory"; - reg = <0x00000000 0x00000000 0x00000000 0x20000000>; - }; - - vcc_sd_reg1: regulator { - compatible = "regulator-gpio"; - regulator-name = "vcc_sd1"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - - gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>; - gpios-states = <0>; - states = <1800000 0x1 - 3300000 0x0>; - enable-active-high; - }; -}; - -/* J9 */ -&pcie0 { - status = "okay"; - phys = <&comphy1 0>; - pinctrl-names = "default"; - pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>; -}; - -/* J6 */ -&sata { - status = "okay"; - phys = <&comphy2 0>; - phy-names = "sata-phy"; -}; - -/* J1 */ -&sdhci1 { - wp-inverted; - bus-width = <4>; - cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>; - marvell,pad-type = "sd"; - vqmmc-supply = <&vcc_sd_reg1>; - - pinctrl-names = "default"; - pinctrl-0 = <&sdio_pins>; - status = "okay"; -}; - -/* U11 */ -&sdhci0 { - non-removable; - bus-width = <8>; - mmc-ddr-1_8v; - mmc-hs400-1_8v; - marvell,xenon-emmc; - marvell,xenon-tun-count = <9>; - marvell,pad-type = "fixed-1-8v"; - - pinctrl-names = "default"; - pinctrl-0 = <&mmc_pins>; -/* - * This eMMC is not populated on all boards, so disable it by - * default and let the bootloader enable it, if it is present - */ - status = "disabled"; -}; - -&spi0 { - status = "okay"; - - flash@0 { - reg = <0>; - compatible = "jedec,spi-nor"; - spi-max-frequency = <104000000>; - m25p,fast-read; - }; -}; - -/* Exported on the micro USB connector J5 through an FTDI */ -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_pins>; - status = "okay"; -}; - -/* - * Connector J17 and J18 expose a number of different features. Some pins are - * multiplexed. This is the case for instance for the following features: - * - UART1 (pin 24 = RX, pin 26 = TX). See armada-3720-db.dts for an example of - * how to enable it. Beware that the signals are 1.8V TTL. - * - I2C - * - SPI - * - MMC - */ - -/* J7 */ -&usb3 { - status = "okay"; -}; - -/* J8 */ -&usb2 { - status = "okay"; -}; - -&mdio { - switch0: switch0@1 { - compatible = "marvell,mv88e6085"; - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - - dsa,member = <0 0>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - label = "cpu"; - ethernet = <ð0>; - phy-mode = "rgmii-id"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - port@1 { - reg = <1>; - label = "wan"; - phy-handle = <&switch0phy0>; - }; - - port@2 { - reg = <2>; - label = "lan0"; - phy-handle = <&switch0phy1>; - }; - - port@3 { - reg = <3>; - label = "lan1"; - phy-handle = <&switch0phy2>; - }; - - }; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - switch0phy0: switch0phy0@11 { - reg = <0x11>; - }; - switch0phy1: switch0phy1@12 { - reg = <0x12>; - }; - switch0phy2: switch0phy2@13 { - reg = <0x13>; - }; - }; - }; -}; - -ð0 { - pinctrl-names = "default"; - pinctrl-0 = <&rgmii_pins>, <&smi_pins>; - phy-mode = "rgmii-id"; - status = "okay"; - - fixed-link { - speed = <1000>; - full-duplex; - }; }; |
