diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pinctrl')
-rw-r--r-- | Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt | 145 |
1 files changed, 145 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt new file mode 100644 index 000000000000..5868a0f7255d --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt @@ -0,0 +1,145 @@ +* Mediatek MT65XX Pin Controller + +The Mediatek's Pin controller is used to control SoC pins. + +Required properties: +- compatible: value should be either of the following. + (a) "mediatek,mt8135-pinctrl", compatible with mt8135 pinctrl. +- mediatek,pctl-regmap: Should be a phandle of the syscfg node. +- pins-are-numbered: Specify the subnodes are using numbered pinmux to + specify pins. +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO + binding is used, the amount of cells must be specified as 2. See the below + mentioned gpio binding representation for description of particular cells. + + Eg: <&pio 6 0> + <[phandle of the gpio controller node] + [line number within the gpio controller] + [flags]> + + Values for gpio specifier: + - Line number: is a value between 0 to 202. + - Flags: bit field of flags, as defined in <dt-bindings/gpio/gpio.h>. + Only the following flags are supported: + 0 - GPIO_ACTIVE_HIGH + 1 - GPIO_ACTIVE_LOW +- reg: physicall address base for EINT registers +- interrupt-controller: Marks the device node as an interrupt controller +- #interrupt-cells: Should be two. +- interrupts : The interrupt outputs from the controller. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices. + +Subnode format +A pinctrl node should contain at least one subnodes representing the +pinctrl groups available on the machine. Each subnode will list the +pins it needs, and how they should be configured, with regard to muxer +configuration, pullups, drive strength, input enable/disable and input schmitt. + + node { + pinmux = <PIN_NUMBER_PINMUX>; + GENERIC_PINCONFIG; + }; + +Required properties: +- pinmux: integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are defined + as macros in boot/dts/<soc>-pinfunc.h directly. + +Optional properties: +- GENERIC_PINCONFIG: is the generic pinconfig options to use, bias-disable, + bias-pull-down, bias-pull-up, input-enable, input-disable, output-low, output-high, + input-schmitt-enable, input-schmitt-disable and drive-strength are valid. + + Some special pins have extra pull up strength, there are R0 and R1 pull-up + resistors available, but for user, it's only need to set R1R0 as 00, 01, 10 or 11. + So when config bias-pull-up, it support arguments for those special pins. + Some macros have been defined for this usage, such as MTK_PUPD_SET_R1R0_00. + See dt-bindings/pinctrl/mt65xx.h. + + When config drive-strength, it can support some arguments, such as + MTK_DRIVE_4mA, MTK_DRIVE_6mA, etc. See dt-bindings/pinctrl/mt65xx.h. + +Examples: + +#include "mt8135-pinfunc.h" + +... +{ + syscfg_pctl_a: syscfg_pctl_a@10005000 { + compatible = "mediatek,mt8135-pctl-a-syscfg", "syscon"; + reg = <0 0x10005000 0 0x1000>; + }; + + syscfg_pctl_b: syscfg_pctl_b@1020C020 { + compatible = "mediatek,mt8135-pctl-b-syscfg", "syscon"; + reg = <0 0x1020C020 0 0x1000>; + }; + + pinctrl@01c20800 { + compatible = "mediatek,mt8135-pinctrl"; + reg = <0 0x1000B000 0 0x1000>; + mediatek,pctl-regmap = <&syscfg_pctl_a &syscfg_pctl_b>; + pins-are-numbered; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; + + i2c0_pins_a: i2c0@0 { + pins1 { + pinmux = <MT8135_PIN_100_SDA0__FUNC_SDA0>, + <MT8135_PIN_101_SCL0__FUNC_SCL0>; + bias-disable; + }; + }; + + i2c1_pins_a: i2c1@0 { + pins { + pinmux = <MT8135_PIN_195_SDA1__FUNC_SDA1>, + <MT8135_PIN_196_SCL1__FUNC_SCL1>; + bias-pull-up = <55>; + }; + }; + + i2c2_pins_a: i2c2@0 { + pins1 { + pinmux = <MT8135_PIN_193_SDA2__FUNC_SDA2>; + bias-pull-down; + }; + + pins2 { + pinmux = <MT8135_PIN_49_WATCHDOG__FUNC_GPIO49>; + bias-pull-up; + }; + }; + + i2c3_pins_a: i2c3@0 { + pins1 { + pinmux = <MT8135_PIN_40_DAC_CLK__FUNC_GPIO40>, + <MT8135_PIN_41_DAC_WS__FUNC_GPIO41>; + bias-pull-up = <55>; + }; + + pins2 { + pinmux = <MT8135_PIN_35_SCL3__FUNC_SCL3>, + <MT8135_PIN_36_SDA3__FUNC_SDA3>; + output-low; + bias-pull-up = <55>; + }; + + pins3 { + pinmux = <MT8135_PIN_57_JTCK__FUNC_GPIO57>, + <MT8135_PIN_60_JTDI__FUNC_JTDI>; + drive-strength = <32>; + }; + }; + + ... + } +}; |