diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt | 153 |
1 files changed, 153 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt new file mode 100644 index 000000000000..d5dac7b843a9 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -0,0 +1,153 @@ +* Renesas Pin Function Controller (GPIO and Pin Mux/Config) + +The Pin Function Controller (PFC) is a Pin Mux/Config controller. On SH7372, +SH73A0, R8A73A4 and R8A7740 it also acts as a GPIO controller. + + +Pin Control +----------- + +Required Properties: + + - compatible: should be one of the following. + - "renesas,pfc-r8a73a4": for R8A73A4 (R-Mobile APE6) compatible pin-controller. + - "renesas,pfc-r8a7740": for R8A7740 (R-Mobile A1) compatible pin-controller. + - "renesas,pfc-r8a7778": for R8A7778 (R-Mobile M1) compatible pin-controller. + - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller. + - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller. + - "renesas,pfc-sh7372": for SH7372 (SH-Mobile AP4) compatible pin-controller. + - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller. + + - reg: Base address and length of each memory resource used by the pin + controller hardware module. + +Optional properties: + + - #gpio-range-cells: Mandatory when the PFC doesn't handle GPIO, forbidden + otherwise. Should be 3. + +The PFC node also acts as a container for pin configuration nodes. Please refer +to pinctrl-bindings.txt in this directory for the definition of the term "pin +configuration node" and for the common pinctrl bindings used by client devices. + +Each pin configuration node represents a desired configuration for a pin, a +pin group, or a list of pins or pin groups. The configuration can include the +function to select on those pin(s) and pin configuration parameters (such as +pull-up and pull-down). + +Pin configuration nodes contain pin configuration properties, either directly +or grouped in child subnodes. Both pin muxing and configuration parameters can +be grouped in that way and referenced as a single pin configuration node by +client devices. + +A configuration node or subnode must reference at least one pin (through the +pins or pin groups properties) and contain at least a function or one +configuration parameter. When the function is present only pin groups can be +used to reference pins. + +All pin configuration nodes and subnodes names are ignored. All of those nodes +are parsed through phandles and processed purely based on their content. + +Pin Configuration Node Properties: + +- renesas,pins : An array of strings, each string containing the name of a pin. +- renesas,groups : An array of strings, each string containing the name of a pin + group. + +- renesas,function: A string containing the name of the function to mux to the + pin group(s) specified by the renesas,groups property + + Valid values for pin, group and function names can be found in the group and + function arrays of the PFC data file corresponding to the SoC + (drivers/pinctrl/sh-pfc/pfc-*.c) + +The pin configuration parameters use the generic pinconf bindings defined in +pinctrl-bindings.txt in this directory. The supported parameters are +bias-disable, bias-pull-up and bias-pull-down. + + +GPIO +---- + +On SH7372, SH73A0, R8A73A4 and R8A7740 the PFC node is also a GPIO controller +node. + +Required Properties: + + - gpio-controller: Marks the device node as a gpio controller. + + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the + GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. + +The syntax of the gpio specifier used by client nodes should be the following +with values derived from the SoC user manual. + + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [flags]> + +On other mach-shmobile platforms GPIO is handled by the gpio-rcar driver. +Please refer to Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +for documentation of the GPIO device tree bindings on those platforms. + + +Examples +-------- + +Example 1: SH73A0 (SH-Mobile AG5) pin controller node + + pfc: pfc@e6050000 { + compatible = "renesas,pfc-sh73a0"; + reg = <0xe6050000 0x8000>, + <0xe605801c 0x1c>; + gpio-controller; + #gpio-cells = <2>; + }; + +Example 2: A GPIO LED node that references a GPIO + + #include <dt-bindings/gpio/gpio.h> + + leds { + compatible = "gpio-leds"; + led1 { + gpios = <&pfc 20 GPIO_ACTIVE_LOW>; + }; + }; + +Example 3: KZM-A9-GT (SH-Mobile AG5) default pin state hog and pin control maps + for the MMCIF and SCIFA4 devices + + &pfc { + pinctrl-0 = <&scifa4_pins>; + pinctrl-names = "default"; + + mmcif_pins: mmcif { + mux { + renesas,groups = "mmc0_data8_0", "mmc0_ctrl_0"; + renesas,function = "mmc0"; + }; + cfg { + renesas,groups = "mmc0_data8_0"; + renesas,pins = "PORT279"; + bias-pull-up; + }; + }; + + scifa4_pins: scifa4 { + renesas,groups = "scifa4_data", "scifa4_ctrl"; + renesas,function = "scifa4"; + }; + }; + +Example 4: KZM-A9-GT (SH-Mobile AG5) default pin state for the MMCIF device + + &mmcif { + pinctrl-0 = <&mmcif_pins>; + pinctrl-names = "default"; + + bus-width = <8>; + vmmc-supply = <®_1p8v>; + status = "okay"; + }; |
