diff options
Diffstat (limited to 'Documentation/devicetree/bindings/drm/msm/dsi.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/drm/msm/dsi.txt | 41 |
1 files changed, 35 insertions, 6 deletions
diff --git a/Documentation/devicetree/bindings/drm/msm/dsi.txt b/Documentation/devicetree/bindings/drm/msm/dsi.txt index cd8fe6cf536c..d56923cd5590 100644 --- a/Documentation/devicetree/bindings/drm/msm/dsi.txt +++ b/Documentation/devicetree/bindings/drm/msm/dsi.txt @@ -30,20 +30,27 @@ Optional properties: - panel@0: Node of panel connected to this DSI controller. See files in Documentation/devicetree/bindings/panel/ for each supported panel. -- qcom,dual-panel-mode: Boolean value indicating if the DSI controller is +- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is driving a panel which needs 2 DSI links. -- qcom,master-panel: Boolean value indicating if the DSI controller is driving +- qcom,master-dsi: Boolean value indicating if the DSI controller is driving the master link of the 2-DSI panel. -- qcom,sync-dual-panel: Boolean value indicating if the DSI controller is +- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is driving a 2-DSI panel whose 2 links need receive command simultaneously. - interrupt-parent: phandle to the MDP block if the interrupt signal is routed through MDP block +- pinctrl-names: the pin control state names; should contain "default" +- pinctrl-0: the default pinctrl state (active) +- pinctrl-n: the "sleep" pinctrl state +- port: DSI controller output port. This contains one endpoint subnode, with its + remote-endpoint set to the phandle of the connected panel's endpoint. + See Documentation/devicetree/bindings/graph.txt for device graph info. DSI PHY: Required properties: - compatible: Could be the following * "qcom,dsi-phy-28nm-hpm" * "qcom,dsi-phy-28nm-lp" + * "qcom,dsi-phy-20nm" - reg: Physical base address and length of the registers of PLL, PHY and PHY regulator - reg-names: The names of register regions. The following regions are required: @@ -59,6 +66,10 @@ Required properties: * "iface_clk" - vddio-supply: phandle to vdd-io regulator device node +Optional properties: +- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY + regulator is wanted. + Example: mdss_dsi0: qcom,mdss_dsi@fd922800 { compatible = "qcom,mdss-dsi-ctrl"; @@ -90,9 +101,13 @@ Example: qcom,dsi-phy = <&mdss_dsi_phy0>; - qcom,dual-panel-mode; - qcom,master-panel; - qcom,sync-dual-panel; + qcom,dual-dsi-mode; + qcom,master-dsi; + qcom,sync-dual-dsi; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mdss_dsi_active>; + pinctrl-1 = <&mdss_dsi_suspend>; panel: panel@0 { compatible = "sharp,lq101r1sx01"; @@ -101,6 +116,18 @@ Example: power-supply = <...>; backlight = <...>; + + port { + panel_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; + + port { + dsi0_out: endpoint { + remote-endpoint = <&panel_in>; + }; }; }; @@ -117,4 +144,6 @@ Example: clock-names = "iface_clk"; clocks = <&mmcc MDSS_AHB_CLK>; vddio-supply = <&pma8084_l12>; + + qcom,dsi-phy-regulator-ldo-mode; }; |
