Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
  bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
  vlan: Calling vlan_hwaccel_do_receive() is always valid.
  tproxy: use the interface primary IP address as a default value for --on-ip
  tproxy: added IPv6 support to the socket match
  cxgb3: function namespace cleanup
  tproxy: added IPv6 support to the TPROXY target
  tproxy: added IPv6 socket lookup function to nf_tproxy_core
  be2net: Changes to use only priority codes allowed by f/w
  tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
  tproxy: added tproxy sockopt interface in the IPV6 layer
  tproxy: added udp6_lib_lookup function
  tproxy: added const specifiers to udp lookup functions
  tproxy: split off ipv6 defragmentation to a separate module
  l2tp: small cleanup
  nf_nat: restrict ICMP translation for embedded header
  can: mcp251x: fix generation of error frames
  can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
  can-raw: add msg_flags to distinguish local traffic
  9p: client code cleanup
  rds: make local functions/variables static
  ...

Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David

1 files changed, 194 insertions, 12 deletions

diff --git a/drivers/net/igb/e1000_phy.c b/drivers/net/igb/e1000_phy.c
index cf1f32300923..ddd036a78999 100644
--- a/drivers/net/igb/e1000_phy.c
+++ b/drivers/net/igb/e1000_phy.c
@@ -570,6 +570,89 @@ out:
 }
 
 /**
+ *  igb_copper_link_setup_m88_gen2 - Setup m88 PHY's for copper link
+ *  @hw: pointer to the HW structure
+ *
+ *  Sets up MDI/MDI-X and polarity for i347-AT4, m88e1322 and m88e1112 PHY's.
+ *  Also enables and sets the downshift parameters.
+ **/
+s32 igb_copper_link_setup_m88_gen2(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+	u16 phy_data;
+
+	if (phy->reset_disable) {
+		ret_val = 0;
+		goto out;
+	}
+
+	/* Enable CRS on Tx. This must be set for half-duplex operation. */
+	ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+	if (ret_val)
+		goto out;
+
+	/*
+	 * Options:
+	 *   MDI/MDI-X = 0 (default)
+	 *   0 - Auto for all speeds
+	 *   1 - MDI mode
+	 *   2 - MDI-X mode
+	 *   3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+	 */
+	phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+
+	switch (phy->mdix) {
+	case 1:
+		phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
+		break;
+	case 2:
+		phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
+		break;
+	case 3:
+		/* M88E1112 does not support this mode) */
+		if (phy->id != M88E1112_E_PHY_ID) {
+			phy_data |= M88E1000_PSCR_AUTO_X_1000T;
+			break;
+		}
+	case 0:
+	default:
+		phy_data |= M88E1000_PSCR_AUTO_X_MODE;
+		break;
+	}
+
+	/*
+	 * Options:
+	 *   disable_polarity_correction = 0 (default)
+	 *       Automatic Correction for Reversed Cable Polarity
+	 *   0 - Disabled
+	 *   1 - Enabled
+	 */
+	phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
+	if (phy->disable_polarity_correction == 1)
+		phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
+
+	/* Enable downshift and setting it to X6 */
+	phy_data &= ~I347AT4_PSCR_DOWNSHIFT_MASK;
+	phy_data |= I347AT4_PSCR_DOWNSHIFT_6X;
+	phy_data |= I347AT4_PSCR_DOWNSHIFT_ENABLE;
+
+	ret_val = phy->ops.write_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+	if (ret_val)
+		goto out;
+
+	/* Commit the changes. */
+	ret_val = igb_phy_sw_reset(hw);
+	if (ret_val) {
+		hw_dbg("Error committing the PHY changes\n");
+		goto out;
+	}
+
+out:
+	return ret_val;
+}
+
+/**
  *  igb_copper_link_setup_igp - Setup igp PHY's for copper link
  *  @hw: pointer to the HW structure
  *
@@ -1124,18 +1207,25 @@ s32 igb_phy_force_speed_duplex_m88(struct e1000_hw *hw)
 			goto out;
 
 		if (!link) {
-			/*
-			 * We didn't get link.
-			 * Reset the DSP and cross our fingers.
-			 */
-			ret_val = phy->ops.write_reg(hw,
-						     M88E1000_PHY_PAGE_SELECT,
-						     0x001d);
-			if (ret_val)
-				goto out;
-			ret_val = igb_phy_reset_dsp(hw);
-			if (ret_val)
-				goto out;
+			if (hw->phy.type != e1000_phy_m88 ||
+			    hw->phy.id == I347AT4_E_PHY_ID ||
+			    hw->phy.id == M88E1112_E_PHY_ID) {
+				hw_dbg("Link taking longer than expected.\n");
+			} else {
+
+				/*
+				 * We didn't get link.
+				 * Reset the DSP and cross our fingers.
+				 */
+				ret_val = phy->ops.write_reg(hw,
+							     M88E1000_PHY_PAGE_SELECT,
+							     0x001d);
+				if (ret_val)
+					goto out;
+				ret_val = igb_phy_reset_dsp(hw);
+				if (ret_val)
+					goto out;
+			}
 		}
 
 		/* Try once more */
@@ -1145,6 +1235,11 @@ s32 igb_phy_force_speed_duplex_m88(struct e1000_hw *hw)
 			goto out;
 	}
 
+	if (hw->phy.type != e1000_phy_m88 ||
+	    hw->phy.id == I347AT4_E_PHY_ID ||
+	    hw->phy.id == M88E1112_E_PHY_ID)
+		goto out;
+
 	ret_val = phy->ops.read_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
 	if (ret_val)
 		goto out;
@@ -1557,6 +1652,93 @@ out:
 	return ret_val;
 }
 
+s32 igb_get_cable_length_m88_gen2(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+	u16 phy_data, phy_data2, index, default_page, is_cm;
+
+	switch (hw->phy.id) {
+	case I347AT4_E_PHY_ID:
+		/* Remember the original page select and set it to 7 */
+		ret_val = phy->ops.read_reg(hw, I347AT4_PAGE_SELECT,
+					    &default_page);
+		if (ret_val)
+			goto out;
+
+		ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT, 0x07);
+		if (ret_val)
+			goto out;
+
+		/* Get cable length from PHY Cable Diagnostics Control Reg */
+		ret_val = phy->ops.read_reg(hw, (I347AT4_PCDL + phy->addr),
+					    &phy_data);
+		if (ret_val)
+			goto out;
+
+		/* Check if the unit of cable length is meters or cm */
+		ret_val = phy->ops.read_reg(hw, I347AT4_PCDC, &phy_data2);
+		if (ret_val)
+			goto out;
+
+		is_cm = !(phy_data & I347AT4_PCDC_CABLE_LENGTH_UNIT);
+
+		/* Populate the phy structure with cable length in meters */
+		phy->min_cable_length = phy_data / (is_cm ? 100 : 1);
+		phy->max_cable_length = phy_data / (is_cm ? 100 : 1);
+		phy->cable_length = phy_data / (is_cm ? 100 : 1);
+
+		/* Reset the page selec to its original value */
+		ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT,
+					     default_page);
+		if (ret_val)
+			goto out;
+		break;
+	case M88E1112_E_PHY_ID:
+		/* Remember the original page select and set it to 5 */
+		ret_val = phy->ops.read_reg(hw, I347AT4_PAGE_SELECT,
+					    &default_page);
+		if (ret_val)
+			goto out;
+
+		ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT, 0x05);
+		if (ret_val)
+			goto out;
+
+		ret_val = phy->ops.read_reg(hw, M88E1112_VCT_DSP_DISTANCE,
+					    &phy_data);
+		if (ret_val)
+			goto out;
+
+		index = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
+			M88E1000_PSSR_CABLE_LENGTH_SHIFT;
+		if (index >= M88E1000_CABLE_LENGTH_TABLE_SIZE - 1) {
+			ret_val = -E1000_ERR_PHY;
+			goto out;
+		}
+
+		phy->min_cable_length = e1000_m88_cable_length_table[index];
+		phy->max_cable_length = e1000_m88_cable_length_table[index + 1];
+
+		phy->cable_length = (phy->min_cable_length +
+				     phy->max_cable_length) / 2;
+
+		/* Reset the page select to its original value */
+		ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT,
+					     default_page);
+		if (ret_val)
+			goto out;
+
+		break;
+	default:
+		ret_val = -E1000_ERR_PHY;
+		goto out;
+	}
+
+out:
+	return ret_val;
+}
+
 /**
  *  igb_get_cable_length_igp_2 - Determine cable length for igp2 PHY
  *  @hw: pointer to the HW structure