Merge tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "A respun version of the merges for the pull request previously sent
  with a few additional fixes.  The last two merges were fixed up by
  hand since the branches have moved on and currently have the prior
  merge in them.

  Quite a busy release for the SPI subsystem, mostly in cleanups big and
  small scattered through the stack rather than anything else:

   - New driver for the Broadcom BC63xx HSSPI controller
   - Fix duplicate device registration for ACPI
   - Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
     changes upon which the transiton depends)
   - Some small optimisations to reduce the amount of time we hold locks
     in the datapath, eliminate some redundant checks and the size of a
     spi_transfer
   - Lots of fixes, cleanups and general enhancements to drivers,
     especially the rspi and Atmel drivers"

* tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (112 commits)
  spi: core: Fix transfer failure when master->transfer_one returns positive value
  spi: Correct set_cs() documentation
  spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer()
  spi: Spelling s/finised/finished/
  spi: sc18is602: Convert to use bits_per_word_mask
  spi: Remove duplicate code to set default bits_per_word setting
  spi/pxa2xx: fix compilation warning when !CONFIG_PM_SLEEP
  spi: clps711x: Add MODULE_ALIAS to support module auto-loading
  spi: rspi: Add missing clk_disable() calls in error and cleanup paths
  spi: rspi: Spelling s/transmition/transmission/
  spi: rspi: Add support for specifying CPHA/CPOL
  spi/pxa2xx: initialize DMA channels to -1 to prevent inadvertent match
  spi: rspi: Add more QSPI register documentation
  spi: rspi: Add more RSPI register documentation
  spi: rspi: Remove dependency on DMAE for SHMOBILE
  spi/s3c64xx: Correct indentation
  spi: sh: Use spi_sh_clear_bit() instead of open-coded
  spi: bitbang: Grammar s/make to make/to make/
  spi: sh-hspi: Spelling s/recive/receive/
  spi: core: Improve tx/rx_nbits check comments
  ...

2 files changed, 8 insertions, 2 deletions

diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt
index 800dafe5b01b..e5a4d1b4acfe 100644
--- a/Documentation/devicetree/bindings/spi/spi-bus.txt
+++ b/Documentation/devicetree/bindings/spi/spi-bus.txt
@@ -67,7 +67,7 @@ only 1(SINGLE), 2(DUAL) and 4(QUAD).
 Dual/Quad mode is not allowed when 3-wire mode is used.
 
 If a gpio chipselect is used for the SPI slave the gpio number will be passed
-via the cs_gpio
+via the SPI master node cs-gpios property.
 
 SPI example for an MPC5200 SPI bus:
 	spi@f00 {
diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt
index 1f9641ade0b5..601a360531a5 100644
--- a/Documentation/devicetree/bindings/spi/ti_qspi.txt
+++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt
@@ -3,6 +3,11 @@ TI QSPI controller.
 Required properties:
 - compatible : should be "ti,dra7xxx-qspi" or "ti,am4372-qspi".
 - reg: Should contain QSPI registers location and length.
+- reg-names: Should contain the resource reg names.
+	- qspi_base: Qspi configuration register Address space
+	- qspi_mmap: Memory mapped Address space
+	- (optional) qspi_ctrlmod: Control module Address space
+- interrupts: should contain the qspi interrupt number.
 - #address-cells, #size-cells : Must be present if the device has sub-nodes
 - ti,hwmods: Name of the hwmod associated to the QSPI
 
@@ -14,7 +19,8 @@ Example:
 
 qspi: qspi@4b300000 {
 	compatible = "ti,dra7xxx-qspi";
-	reg = <0x4b300000 0x100>;
+	reg = <0x47900000 0x100>, <0x30000000 0x3ffffff>;
+	reg-names = "qspi_base", "qspi_mmap";
 	#address-cells = <1>;
 	#size-cells = <0>;
 	spi-max-frequency = <25000000>;