dt-bindings: consolidate display related bindings

This is a quite large renaming to consolidate display related bindings
into a single "display" directory from various scattered locations of
video, drm, gpu, fb, mipi, and panel. The prior location was somewhat
based on the Linux driver location, but bindings should be independent
of that.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>

3 files changed, 143 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/display/tilcdc/panel.txt b/Documentation/devicetree/bindings/display/tilcdc/panel.txt
new file mode 100644
index 000000000000..f20b31cdc59a
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/tilcdc/panel.txt
@@ -0,0 +1,66 @@
+Device-Tree bindings for tilcdc DRM generic panel output driver
+
+Required properties:
+ - compatible: value should be "ti,tilcdc,panel".
+ - panel-info: configuration info to configure LCDC correctly for the panel
+   - ac-bias: AC Bias Pin Frequency
+   - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt
+   - dma-burst-sz: DMA burst size
+   - bpp: Bits per pixel
+   - fdd: FIFO DMA Request Delay
+   - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling
+   - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore
+   - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most
+   - fifo-th: DMA FIFO threshold
+ - display-timings: typical videomode of lcd panel.  Multiple video modes
+   can be listed if the panel supports multiple timings, but the 'native-mode'
+   should be the preferred/default resolution.  Refer to
+   Documentation/devicetree/bindings/display/display-timing.txt for display
+   timing binding details.
+
+Optional properties:
+- backlight: phandle of the backlight device attached to the panel
+- enable-gpios: GPIO pin to enable or disable the panel
+
+Recommended properties:
+ - pinctrl-names, pinctrl-0: the pincontrol settings to configure
+   muxing properly for pins that connect to TFP410 device
+
+Example:
+
+	/* Settings for CDTech_S035Q01 / LCD3 cape: */
+	lcd3 {
+		compatible = "ti,tilcdc,panel";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bone_lcd3_cape_lcd_pins>;
+		backlight = <&backlight>;
+		enable-gpios = <&gpio3 19 0>;
+
+		panel-info {
+			ac-bias           = <255>;
+			ac-bias-intrpt    = <0>;
+			dma-burst-sz      = <16>;
+			bpp               = <16>;
+			fdd               = <0x80>;
+			sync-edge         = <0>;
+			sync-ctrl         = <1>;
+			raster-order      = <0>;
+			fifo-th           = <0>;
+		};
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: 320x240 {
+				hactive         = <320>;
+				vactive         = <240>;
+				hback-porch     = <21>;
+				hfront-porch    = <58>;
+				hsync-len       = <47>;
+				vback-porch     = <11>;
+				vfront-porch    = <23>;
+				vsync-len       = <2>;
+				clock-frequency = <8000000>;
+				hsync-active    = <0>;
+				vsync-active    = <0>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/display/tilcdc/tfp410.txt b/Documentation/devicetree/bindings/display/tilcdc/tfp410.txt
new file mode 100644
index 000000000000..a58ae7756fc6
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/tilcdc/tfp410.txt
@@ -0,0 +1,21 @@
+Device-Tree bindings for tilcdc DRM TFP410 output driver
+
+Required properties:
+ - compatible: value should be "ti,tilcdc,tfp410".
+ - i2c: the phandle for the i2c device to use for DDC
+
+Recommended properties:
+ - pinctrl-names, pinctrl-0: the pincontrol settings to configure
+   muxing properly for pins that connect to TFP410 device
+ - powerdn-gpio: the powerdown GPIO, pulled low to power down the
+   TFP410 device (for DPMS_OFF)
+
+Example:
+
+	dvicape {
+		compatible = "ti,tilcdc,tfp410";
+		i2c = <&i2c2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bone_dvi_cape_dvi_00A1_pins>;
+		powerdn-gpio = <&gpio2 31 0>;
+	};
diff --git a/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt
new file mode 100644
index 000000000000..2136ee81e061
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt
@@ -0,0 +1,56 @@
+Device-Tree bindings for tilcdc DRM driver
+
+Required properties:
+ - compatible: value should be "ti,am33xx-tilcdc".
+ - interrupts: the interrupt number
+ - reg: base address and size of the LCDC device
+
+Recommended properties:
+ - interrupt-parent: the phandle for the interrupt controller that
+   services interrupts for this device.
+ - ti,hwmods: Name of the hwmod associated to the LCDC
+
+Optional properties:
+ - max-bandwidth: The maximum pixels per second that the memory
+   interface / lcd controller combination can sustain
+ - max-width: The maximum horizontal pixel width supported by
+   the lcd controller.
+ - max-pixelclock: The maximum pixel clock that can be supported
+   by the lcd controller in KHz.
+
+Optional nodes:
+
+ - port/ports: to describe a connection to an external encoder. The
+   binding follows Documentation/devicetree/bindings/graph.txt and
+   suppors a single port with a single endpoint.
+
+Example:
+
+	fb: fb@4830e000 {
+		compatible = "ti,am33xx-tilcdc";
+		reg = <0x4830e000 0x1000>;
+		interrupt-parent = <&intc>;
+		interrupts = <36>;
+		ti,hwmods = "lcdc";
+
+		port {
+			lcdc_0: endpoint@0 {
+				remote-endpoint = <&hdmi_0>;
+			};
+		};
+	};
+
+	tda19988: tda19988 {
+		compatible = "nxp,tda998x";
+		reg = <0x70>;
+
+		pinctrl-names = "default", "off";
+		pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+		pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
+
+		port {
+			hdmi_0: endpoint@0 {
+				remote-endpoint = <&lcdc_0>;
+			};
+		};
+	};