1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
|
/*
* Copyright (c) 2009 Wind River Systems, Inc.
* Tom Rix <Tom.Rix@windriver.com>
*
* Derived from Zoom1 code by
* Nishanth Menon <nm@ti.com>
* Sunil Kumar <sunilsaini05@gmail.com>
* Shashi Ranjan <shashiranjanmca05@gmail.com>
* Richard Woodruff <r-woodruff2@ti.com>
* Syed Mohammed Khasim <khasim@ti.com>
*
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <netdev.h>
#ifdef CONFIG_STATUS_LED
#include <status_led.h>
#endif
#include <twl4030.h>
#include <asm/io.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/gpio.h>
#include <asm/arch/mem.h>
#include <asm/arch/mux.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-types.h>
#include "zoom2.h"
#include "zoom2_serial.h"
DECLARE_GLOBAL_DATA_PTR;
/*
* This the the zoom2, board specific, gpmc configuration for the
* quad uart on the debug board. The more general gpmc configurations
* are setup at the cpu level in arch/arm/cpu/armv7/omap3/mem.c
*
* The details of the setting of the serial gpmc setup are not available.
* The values were provided by another party.
*/
static u32 gpmc_serial_TL16CP754C[GPMC_MAX_REG] = {
0x00011000,
0x001F1F01,
0x00080803,
0x1D091D09,
0x041D1F1F,
0x1D0904C4, 0
};
/* Used to track the revision of the board */
static zoom2_revision revision = ZOOM2_REVISION_UNKNOWN;
/*
* Routine: zoom2_get_revision
* Description: Return the revision of the Zoom2 this code is running on.
*/
zoom2_revision zoom2_get_revision(void)
{
return revision;
}
/*
* Routine: zoom2_identify
* Description: Detect which version of Zoom2 we are running on.
*/
void zoom2_identify(void)
{
/*
* To check for production board vs beta board,
* check if gpio 94 is clear.
*
* No way yet to check for alpha board identity.
* Alpha boards were produced in very limited quantities
* and they are not commonly used. They are mentioned here
* only for completeness.
*/
if (!gpio_request(94, "")) {
unsigned int val;
gpio_direction_input(94);
val = gpio_get_value(94);
if (val)
revision = ZOOM2_REVISION_BETA;
else
revision = ZOOM2_REVISION_PRODUCTION;
}
printf("Board revision ");
switch (revision) {
case ZOOM2_REVISION_PRODUCTION:
printf("Production\n");
break;
case ZOOM2_REVISION_BETA:
printf("Beta\n");
break;
default:
printf("Unknown\n");
break;
}
}
/*
* Routine: board_init
* Description: Early hardware init.
*/
int board_init (void)
{
u32 *gpmc_config;
gpmc_init (); /* in SRAM or SDRAM, finish GPMC */
/* Configure console support on zoom2 */
gpmc_config = gpmc_serial_TL16CP754C;
enable_gpmc_cs_config(gpmc_config, &gpmc_cfg->cs[3],
SERIAL_TL16CP754C_BASE, GPMC_SIZE_16M);
/* board id for Linux */
gd->bd->bi_arch_number = MACH_TYPE_OMAP_ZOOM2;
/* boot param addr */
gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
status_led_set (STATUS_LED_BOOT, STATUS_LED_ON);
#endif
return 0;
}
/*
* Routine: misc_init_r
* Description: Configure zoom board specific configurations
*/
int misc_init_r(void)
{
zoom2_identify();
twl4030_power_init();
twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
dieid_num_r();
/*
* Board Reset
* The board is reset by holding the the large button
* on the top right side of the main board for
* eight seconds.
*
* There are reported problems of some beta boards
* continously resetting. For those boards, disable resetting.
*/
if (ZOOM2_REVISION_PRODUCTION <= zoom2_get_revision())
twl4030_power_reset_init();
return 0;
}
/*
* Routine: set_muxconf_regs
* Description: Setting up the configuration Mux registers specific to the
* hardware. Many pins need to be moved from protect to primary
* mode.
*/
void set_muxconf_regs (void)
{
/* platform specific muxes */
MUX_ZOOM2 ();
}
#ifdef CONFIG_GENERIC_MMC
int board_mmc_init(bd_t *bis)
{
return omap_mmc_init(0, 0, 0, -1, -1);
}
#endif
#ifdef CONFIG_CMD_NET
int board_eth_init(bd_t *bis)
{
int rc = 0;
#ifdef CONFIG_LAN91C96
rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE);
#endif
return rc;
}
#endif
|
