1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
|
/*
* (C) Copyright 2000-2006
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <asm/immap.h>
int checkboard (void) {
puts ("Board: Freescale M5271EVB\n");
return 0;
};
phys_size_t initdram (int board_type) {
int i;
/* Enable Address lines 23-21 and lower 16bits of data path */
mbar_writeByte(MCF_GPIO_PAR_AD, MCF_GPIO_AD_ADDR23 |
MCF_GPIO_AD_ADDR22 | MCF_GPIO_AD_ADDR21 |
MCF_GPIO_AD_DATAL);
/* Set CS2 pin to be SD_CS0 */
mbar_writeByte(MCF_GPIO_PAR_CS, mbar_readByte(MCF_GPIO_PAR_CS)
| MCF_GPIO_PAR_CS_PAR_CS2);
/* Configure SDRAM Control Pin Assignemnt Register */
mbar_writeByte(MCF_GPIO_PAR_SDRAM, MCF_GPIO_SDRAM_CSSDCS_00 |
MCF_GPIO_SDRAM_SDWE | MCF_GPIO_SDRAM_SCAS |
MCF_GPIO_SDRAM_SRAS | MCF_GPIO_SDRAM_SCKE |
MCF_GPIO_SDRAM_SDCS_11);
asm(" nop");
/*
* Check to see if the SDRAM has already been initialized
* by a run control tool
*/
if (!(mbar_readLong(MCF_SDRAMC_DACR0) & MCF_SDRAMC_DACRn_RE)) {
/* Initialize DRAM Control Register: DCR */
mbar_writeShort(MCF_SDRAMC_DCR,
MCF_SDRAMC_DCR_RTIM(2)
| MCF_SDRAMC_DCR_RC(0x2E));
asm(" nop");
/*
* Initialize DACR0
*
* CASL: 01
* CBM: cmd at A20, bank select bits 21 and up
* PS: 32bit port size
*/
mbar_writeLong(MCF_SDRAMC_DACR0,
MCF_SDRAMC_DACRn_BA(CONFIG_SYS_SDRAM_BASE>>18)
| MCF_SDRAMC_DACRn_CASL(1)
| MCF_SDRAMC_DACRn_CBM(3)
| MCF_SDRAMC_DACRn_PS(0));
asm(" nop");
/* Initialize DMR0 */
mbar_writeLong(MCF_SDRAMC_DMR0,
MCF_SDRAMC_DMRn_BAM_16M
| MCF_SDRAMC_DMRn_V);
asm(" nop");
/* Set IP bit in DACR */
mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
| MCF_SDRAMC_DACRn_IP);
asm(" nop");
/* Wait at least 20ns to allow banks to precharge */
for (i = 0; i < 5; i++)
asm(" nop");
/* Write to this block to initiate precharge */
*(u32 *)(CONFIG_SYS_SDRAM_BASE) = 0xa5a5a5a5;
asm(" nop");
/* Set RE bit in DACR */
mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
| MCF_SDRAMC_DACRn_RE);
/* Wait for at least 8 auto refresh cycles to occur */
for (i = 0; i < 2000; i++)
asm(" nop");
/* Finish the configuration by issuing the MRS */
mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
| MCF_SDRAMC_DACRn_MRS);
asm(" nop");
/*
* Write to the SDRAM Mode Register A0-A11 = 0x400
*
* Write Burst Mode = Programmed Burst Length
* Op Mode = Standard Op
* CAS Latency = 2
* Burst Type = Sequential
* Burst Length = 1
*/
*(u32 *)(CONFIG_SYS_SDRAM_BASE + 0x400) = 0xa5a5a5a5;
asm(" nop");
}
return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
};
int testdram (void) {
/* TODO: XXX XXX XXX */
printf ("DRAM test not implemented!\n");
return (0);
}
|
