summaryrefslogtreecommitdiffstats
path: root/drivers/mtd/st_smi.c
Commit message (Collapse)AuthorAgeFilesLines
* MTD: SPEAr SMI: Add write support for length < 4 bytesStefan Roese2012-07-071-4/+18
| | | | | | | | Needed for redundant environment for example. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Amit Virdi <amit.virdi@st.com> Cc: Vipin Kumar <vipin.kumar@st.com>
* st_smi: Fixed page size for Winbond W25Q128FV flashArmando Visconti2012-07-071-1/+1
| | | | | | Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Change timeout loop implementationAmit Virdi2012-07-071-10/+17
| | | | | | | | | | | There are two problems in the current timeout loop implementation: 1. In case initial test failing, there will always be a delay of 1 ms 2. The delay duration is not tunable The new implementation addresses both these limitations. Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Fix bug in flash_print_info()Armando Visconti2012-07-071-2/+7
| | | | | | | | | If the flash size was smaller than 1MB then flash_print_info() was erroneously reporting 0 MB. Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Change the flash probing methodArmando Visconti2012-07-071-27/+65
| | | | | | | | | | THis patch introduces a new methodology for flash probing in which flash_devices[] table, looked-up thru the dev_id, is used to locate the flash geometry and information. Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Removed no needed dependency on ST_M25Pxx_IDArmando Visconti2012-07-071-32/+18
| | | | | | | | | | Since the smi erase code is very generic and works for any kind of flash, there is no need to test for ST_M25Pxx_ID flash types like m25p40 flashes). Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Fix smi read statusVipin Kumar2012-07-071-6/+2
| | | | | | | | | | | | smi_read_sr fails sometimes because of TFF not getting set within assumed time. This condition may arise because of, for example, smi memory being in a erase mode. This fix is to enable reading the status register until timeout. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Move status register read before modifying ctrl registerShiraz Hashim2012-07-071-2/+4
| | | | | | Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Read status until timeout happensVipin KUMAR2012-07-071-1/+1
| | | | | | | | | SMI driver read status fails because the control register could not be overwritten. Instead, the read status should be tried until timeout. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Enhance the error handlingAmit Virdi2012-07-071-13/+21
| | | | | | | | | | | This commit does the following: - Reports error if SNOR flash is not found on the board - Changes smi_read_sr to return error using which a retry mechanism is implemented for reading flash status Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Return error in case TFF is not setAmit Virdi2012-07-071-8/+14
| | | | | | | | | | Curently the code makes wrong assumption that the Transfer finished flag shall be set within the stipulated time. However, there may occur a scenario in which the TFF flag is not set. Return error in that case. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Add support for SPEAr SMI driverVipin KUMAR2012-07-071-0/+519
SMI is the serial memory interface controller provided by ST. Earlier, a driver exists in the u-boot source code for the SMI IP. However, it was specific to spear platforms. This commit converts the same driver to a more generic driver. As a result, the driver files are renamed to st_smi.c and st_smi.h and moved into drivers/mtd folder for reusability by other platforms using smi controller peripheral. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
OpenPOWER on IntegriCloud