summaryrefslogtreecommitdiffstats
path: root/board/freescale/corenet_ds
Commit message (Collapse)AuthorAgeFilesLines
* powerpc/mpc85xx: SECURE BOOT- Add secure boot target for P5040DSgaurav rana2015-01-161-0/+1
| | | | | | | Secure boot target is added for P5040DS platform. Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/hydra: fix judging condition of RGMII selectionMinghuan Lian2014-12-051-1/+2
| | | | | | | | | | BRDCFG1_EMI1_SEL_MASK has been changed to 0x78, which contains selection bits and connected status bit. So the Corresponding mux value of RGMII is changed to BRDCFG1_EMI1_SEL_RGMII | BRDCFG1_EMI1_EN. Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/hydra: Update MDIO mux fixupsChunhe Lan2014-12-051-1/+3
| | | | | | | | | | | | | The new device trees use a more generic interface for supporting muxing mdio buses. The mux property is thus specified in "reg", rather than "fsl,hydra-mdio-muxval". In order to support using old device trees, we keep the old fixup in there. Linux will therefore see the both properties, but will ignore fsl,hydra-mdio-muxval. Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* fdt: Allow ft_board_setup() to report failureSimon Glass2014-11-211-1/+3
| | | | | | | | | | | | | | | | | | This function can fail if the device tree runs out of space. Rather than silently booting with an incomplete device tree, allow the failure to be detected. Unfortunately this involves changing a lot of places in the code. I have not changed behvaiour to return an error where one is not currently returned, to avoid unexpected breakage. Eventually it would be nice to allow boards to register functions to be called to update the device tree. This would avoid all the many functions to do this. However it's not clear yet if this should be done using driver model or with a linker list. This work is left for later. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
* MAINTAINERS: comment out blank M: fieldMasahiro Yamada2014-09-241-1/+1
| | | | | | | | | | | | | | | | | | Since commit ddaf5c8f3030050fcd356a1e49e3ee8f8f52c6d4 (patman: RunPipe() should not pipe stdout/stderr unless asked), Patman spits lots of "Invalid MAINTAINERS address: '-'" error messages for patches with global changes. It takes too long for Patman to process them. Anyway, "M: -" does not carry any important information. Rather, it is just like a place holder in case of assigning a new board maintainer. Let's comment out. This commit can be reproduced by the following command: find . -name MAINTAINERS | xargs sed -i -e '/^M:[[:blank:]]*-$/s/^/#/' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* kconfig: remove redundant "string" type in arch and board KconfigsMasahiro Yamada2014-09-131-12/+0
| | | | | | | | | | | | | | | | | | Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME} are specified in arch/Kconfig. We can delete the ones in arch and board Kconfig files. This commit can be easily reproduced by the following command: find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e ' /config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ { N s/\n[[:space:]]*string// } ' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* Add board MAINTAINERS filesMasahiro Yamada2014-07-301-0/+29
| | | | | | | | | | | | | | | | | | | | We have switched to Kconfig and the boards.cfg file is going to be removed. We have to retrieve the board status and maintainers information from it. The MAINTAINERS format as in Linux Kernel would be nice because we can crib the scripts/get_maintainer.pl script. After some discussion, we chose to put a MAINTAINERS file under each board directory, not the top-level one because we want to collect relevant information for a board into a single place. TODO: Modify get_maintainer.pl to scan multiple MAINTAINERS files. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Suggested-by: Tom Rini <trini@ti.com> Acked-by: Simon Glass <sjg@chromium.org>
* kconfig: add board Kconfig and defconfig filesMasahiro Yamada2014-07-301-0/+63
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds: - arch/${ARCH}/Kconfig provide a menu to select target boards - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig set CONFIG macros to the appropriate values for each board - configs/${TARGET_BOARD}_defconfig default setting of each board (This commit was automatically generated by a conversion script based on boards.cfg) In Linux Kernel, defconfig files are located under arch/${ARCH}/configs/ directory. It works in Linux Kernel since ARCH is always given from the command line for cross compile. But in U-Boot, ARCH is not given from the command line. Which means we cannot know ARCH until the board configuration is done. That is why all the "*_defconfig" files should be gathered into a single directory ./configs/. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
* powerpc/mpc85xx: Check return value of find_tlb_idxYork Sun2014-07-221-3/+9
| | | | | | | | | | find_tlb_idx() is called in board_early_init_r() on multiple boards. The return value is not checked before being used to disable a TLB. In normal case the return value wouldn't be -1. In case of a mis- configuration during porting to a new board, checking the return value may be helpful to reveal some user errors. Signed-off-by: York Sun <yorksun@freescale.com>
* Driver/DDR: Moving Freescale DDR driver to a common driverYork Sun2013-11-256-7/+7
| | | | | | | Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs. The similar DDR controllers will be used for ARM-based SoCs. Signed-off-by: York Sun <yorksun@freescale.com>
* board: powerpc: convert makefiles to Kbuild styleMasahiro Yamada2013-11-011-30/+10
| | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Stefan Roese <sr@denx.de>
* fsl/mpc85xx: define common serdes_clock_to_string functionValentin Longchamp2013-10-241-14/+0
| | | | | | | | | | | | This allows to share some common code for the boards that use a corenet base SoC. Two different versions of the function are available in fsl_corenet_serdes.c and fsl_corenet2_serdes.c files. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: fix t1040qds.c] Acked-by: York Sun <yorksun@freescale.com>
* powerpc: Fix CamelCase warnings in DDR related codePriyanka Jain2013-10-161-3/+3
| | | | | | | | | | | Some DDR related structures present in fsl_ddr_dimm_params.h, fsl_ddr_sdram.h, ddr_spd.h has various parameters with embedded acronyms capitalized that trigger the CamelCase warning in checkpatch.pl Convert those variable names to smallcase naming convention and modify all files which are using these structures with modified structures. Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
* SGMII:fix PHY addresses for QSGMII Riser Card working in SGMII modeZhao Qiang2013-10-163-0/+68
| | | | | | | | | | | | | | | | | | | | | Fix PHY addresses for QSGMII Riser Card working in SGMII mode on board P3041/P5020/P4080/P5040/B4860. QSGMII Riser Card can work in SGMII mode, but having the different PHY addresses. So the following steps should be done: 1. Confirm whether QSGMII Riser Card is used. 2. If yes, set the proper PHY address. Generally, the function is_qsgmii_riser_card() is for step 1, and set_sgmii_phy() for step 2. However, there are still some special situations, take P5040 and B4860 as examples, the PHY addresses need to be changed when serdes protocol is changed, so it is necessary to confirm the protocol before setting PHY addresses. Signed-off-by: Zhao Qiang <B45475@freescale.com>
* Corenet/p5040/SGMII:fix the problem for SGMII5/6Zhao Qiang2013-10-161-4/+18
| | | | | | | | | | | SGMII5/6 and SGMII7/8 are not on the same slot on P5040 according to the serdes protocol. So it is not proper to organize SGMII5/6 and SGMII7/8 on one bus and SGMII5/6 can't work. So a new bus SUPER_HYDRA_FM3_SGMII_MDIO is added for SGMII5/6 Signed-off-by: Zhao Qiang <B45475@freescale.com>
* powerpc/mpc8xxx: Add memory reset controlYork Sun2013-08-091-2/+2
| | | | | | | | | JEDEC spec requires the clocks to be stable before deasserting reset signal for RDIMMs. Clocks start when any chip select is enabled and clock control register is set. This patch also adds the interface to toggle memory reset signal if needed by the boards. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/corenet: Move RCW print to cpu.cYork Sun2013-08-091-14/+3
| | | | | | | The RCW print is common for all corenet platforms. Not necessary to ducplicate in each board file. Signed-off-by: York Sun <yorksun@freescale.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-247-116/+7
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* powerpc/p5040: fix mdio mux for 10G portShaohui Xie2013-05-241-4/+4
| | | | | | | | | | | | Current driver of p5040 assumes 10G port follows 1G port DTSEC5 in eth port enum structure, it will assign mdio mux depend on this assumption. This is not true with Fman V3, which added more 1G ports after port DTSEC5 in eth port enum structure, then 10G ports on p5040 will have wrong mdio mux. So we use dynamic index for 10G ports instead of hardcoded enum value when doing mdio mux for 10G ports. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/p5040: enable PBL tool supportShaohui Xie2013-05-241-0/+11
| | | | | | | | Provided a default RCW for P5040, then it can use PBL to build ramboot image. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* Fix references to the documentation filesAnatolij Gustschin2013-05-101-1/+1
| | | | | | | | | | | | Many boot image configuration files refer to the appropriate documentation file, but these references contain typos in the directory and file name. Fix them. Also fix reference to doc/README.SPL file. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* ppc: Move lbc_clk and cpu to arch_global_dataSimon Glass2013-02-041-1/+1
| | | | | | | | Move these fields into arch_global_data and tidy up. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Update for bsc9132qds.c, b4860qds.c] Signed-off-by: Tom Rini <trini@ti.com>
* powerpc/p2041: add RCW file for P2041RDBValentin Longchamp2013-01-301-0/+11
| | | | | | | | | | | | All the dev boards of Freescale's QorIQ family have a RCW that is supported by the u-boot.pbl build target. This patch adds one for the P2041 dev board. This RCW is suitable for the RAMBOOT_PBL scenarios and was tested on the P2041RDB booting from the eSPI NOR Flash (P2041RDB_SPIFLASH config). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet_ds: Update DDR timing for single-rank DIMMsYork Sun2012-11-271-2/+2
| | | | | | | | Single rank UDIMM timing has been verified with HMT325U7BFR8C-H9 for speed 800, 900, 1000, 1200, 1300MT/s. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: add support for the Freescale P5040DS Superhydra reference boardTimur Tabi2012-11-274-6/+758
| | | | | | | | | The P5040DS reference board (a.k.a "Superhydra") is an enhanced version of P3041DS/P5020DS ("Hydra") reference board. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: get rid of enum board_slots in P4080 MDIO driverTimur Tabi2012-08-231-40/+19
| | | | | | | | | enum board_slots contained six values, where SLOT1 == 1, SLOT2 == 2, and so on. This is pointless, so remove it. Also move the lane_to_slot[] array to the top of the file so that it can be used by other functions. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/CoreNet: add tool to support pbl image build.Shaohui Xie2012-08-234-0/+84
| | | | | | | | | | Provides a tool to build boot Image for PBL(Pre boot loader) which is used on Freescale CoreNet SoCs, PBL can be used to load some instructions and/or data for pre-initialization. The default output image is u-boot.pbl, for more details please refer to doc/README.pblimage. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during bootTimur Tabi2012-04-241-4/+0
| | | | | | | | | | | | | | | | Most 85xx boards can be built as a 32-bit or a 36-bit. Current code sometimes displays which of these is actually built, but it's inconsistent. This is especially problematic since the "default" build for a given 85xx board can be either one, so if you don't see a message, you can't always know which size is being used. Not only that, but each board includes code that displays the message, so there is duplication. The 'bdinfo' command has been updated to display this information, so we don't need to display it at boot time. The board-specific code is deleted. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* net: phy: make board_phy_config responsible for calling drv->configTroy Kisky2012-02-271-0/+2
| | | | | | | | | Boards may have things they want done before or after normal phy config. Letting the boards call drv->config allows them more flexibilty. Boards affected by this change are corenet_ds and mpc8544ds. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
* powerpc/QorIQ: fix network frame manager TBI PHY address settingsRoy Zang2011-11-082-16/+0
| | | | | | | | | | | | TBI PHY address (TBIPA) register has been set in general frame manager phy init funciton dtsec_init_phy() in drivers/net/fm/eth.c So remove the duplicate code on QorIQ frame manager Ethernet related platforms, which include Hydra board, P4080DS board and P2041rdb board. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Cc: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: wait for alignment before resetting SERDES RX lanes (SERDES9)Timur Tabi2011-10-201-8/+30
| | | | | | | | The work-around for P4080 erratum SERDES9 says that the SERDES receiver lanes should be reset after the XAUI starts tranmitting alignment signals. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* fdt: Add new fdt_set_node_status & fdt_set_status_by_alias helpersShengzhou Liu2011-10-182-48/+14
| | | | | | | | | | | | | | | | | | | | | | | | Add common function fdt_set_node_status() to assist in various locations that we set a nodes status. This function utilizes the status values that are part of the EPAPR spec (on power.org). fdt_set_status_by_alias() is based on fdt_set_node_status() but uses an alias string to identify the node to update. We also add some shortcut functions to help the common cases of setting "okay" and "disabled": fdt_status_okay() fdt_status_disabled() fdt_status_okay_by_alias() fdt_status_disabled_by_alias() Finally, we fixup the corenet_ds ethernet code which previously had a function by the same name that can be replaced with the new helpers. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Gerald Van Baren <vanbaren@cideas.com>
* punt unused clean/distclean targetsMike Frysinger2011-10-151-6/+0
| | | | | | | | | | The top level Makefile does not do any recursion into subdirs when cleaning, so these clean/distclean targets in random arch/board dirs never get used. Punt them all. MAKEALL didn't report any errors related to this that I could see. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* powerpc/mpc8xxx: Merge entries in DDR speed tableYork Sun2011-10-091-125/+97
| | | | | | | | | | | | | | | It is not necessary to keep multiple entries for the same setting in DDR speed tables. Merge them for smaller tables. Also restructure the tables for smaller size. Cleanup some typedefs. Enforce strict checking for speed table. If DIMM is running at higher than known speed, try to use the highest speed setting. If rank is unknown, it has to panic. Removed ODT overriding for P2020DS as it is not necessary. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: refactor common P-Series CoreNet files for FSL boardsKumar Gala2011-09-294-226/+0
| | | | | | | | | | | | | | | | We currently support 4 SoC/Boards from the P-Series of QorIQ SoCs that are based on the 'CoreNet' Architecture: P2041RDB, P3041DS, P4080DS, and P5020DS. There is a significant amount of commonality shared between these boards that we can refactor into common code: * Initial LAW setup * Initial TLB setup * PCI setup We start by moving the shared code between P3041DS, P4080DS, and P5020DS into a common directory to be shared with other P-Series CoreNet boards. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMMYork Sun2011-09-291-19/+84
| | | | | | | | | | | RDIMM has different timing parameters from UDIMM. Create new tables for RDIMMs. Single-, dual- and quad-rank RDIMMs have been verified with speeds from 800 to 1333MT/s. Speed table expands to include 1600MT/s for future use. Single- and quad-rank RDIMM entries are copied into UDIMM tables for future use. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/mpc8xxx: Move DDR RCW overriding to common codeYork Sun2011-09-291-14/+0
| | | | | | | | DDR RCW varies at different speeds. It is common for all platform. Move it out from corenet_ds. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Cleanup extern in corenet_ds board codeKumar Gala2011-09-292-2/+1
| | | | | | Move extern of pci_of_setup() into corenet_ds.h Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/hydra: Add ethernet support on P5020/P3041 DS boardsTimur Tabi2011-09-292-0/+555
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for RGMII, SGMII, and XAUI (10Gb) Ethernet on P3041DS & P5020DS ("Hydra"). The lane_to_slot[] array is initialized dynamically, since board switches can be used to control the muxing of SERDES lanes to slots. The BRDCFG1 PIXIS register is used to route the MII bus to the appropriate slot. The SERDES configuration is queried to help determine the routing between MACs and slot/phy combination. If a XAUI card is inserted, muxing for that card is enabled and never turned off. The PHY address for the 10G XAUI card depends on the slot in which it's inserted. If it's in slot 1, the address is 4. If it's in slot 2, the address is 0. Update the MDIO routing in the P3041DS and P5020DS device trees based on the board-level muxing. The SERDES configuration determines which SGMII/XGMII boards are located in which slots, and so the MDIO bus needs to be muxed correctly whenever talking to a PHY connected to any Fman MAC. The Fman Ethernet nodes in the device tree also need to be routed to the correct PHYs. Removed CONFIG_SYS_FMAN_FW as its not used anywhere. Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add FMan ethernet support to P4080DSAndy Fleming2011-09-294-4/+538
| | | | | | | | | | | | | | | | | | | | | | | Add support for RGMII, SGMII, and XAUI (10Gb) Ethernet on P4080DS. The board supports add-on cards for SGMII and XAUI functionality. Which slots on the board these cards are in is a function of the SERDES option selected and muxes on the board. Additionally because of the high-configurablity which MDIO bus one is connected to is "selected" via an FPGA register. We create dummy MDIO bus for the phy layer and hide the mux manipulation in this dummy layer. Add fman fdt helper function in board common code it'll be used by several freescale boards that do various muxing of the MDIO signals based on which controller/interface one is trying to talk to. Removed CONFIG_SYS_FMAN_FW as its not used anywhere. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entriesKumar Gala2011-09-291-15/+15
| | | | | | | We shouldn't be setting execute permissions on TLB entries that will not actually have any code run from them. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: enable USB2 gadget mode for corenet ds boardShaohui Xie2011-07-291-0/+1
| | | | | | | | | | to make USB2 worked in gadget mode, we need to set it's 'dr_mode' to 'peripheral' in hwconfig, but driver starts scan from 'usb1', it'll break out if it cannot find 'usb1', so drop the 'else' clause to make driver scan all the 'usbx'. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* MPC8xxx: drop redundant boot messagesWolfgang Denk2011-07-291-1/+1
| | | | | | | | | | | | | | | Current code would print RAM size information like this: DRAM: DDR: 256 MiB (DDR1, 64-bit, CL=2, ECC off) Turn a number of printf()s into debug() to get rid of the redundant "DDR: " string like this: DRAM: 256 MiB (DDR1, 64-bit, CL=2, ECC off) Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Adding configuration for DCSRCR to enable 32M accessStephen George2011-07-291-1/+2
| | | | | | | | | | | | | | | Configuring DCSRCR to define the DCSR space to be 1G instead of the default 4M. DCSRCR only allows selection of either 4M or 1G. Most DCSR registers are within 4M but the Nexus trace buffer is located at offset 16M within the DCSR. Configuring the LAW to be 32M to allow access to the Nexus trace buffer. No TLB modification is required since accessing the Nexus trace buffer from within u-boot is not required. Signed-off-by: Stephen George <stephen.george@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/mpc85xx: Display a warning for unsupported DDR data ratesYork Sun2011-07-111-0/+6
| | | | | | | | If DDR initialziation uses a speed table and the speed is not matched, print a warning message instead of silently ignoring. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/corenet_ds: Fix RCW overriding for RDIMMYork Sun2011-07-111-1/+1
| | | | | | | Allow overriding RCW for all RDIMM, not only quad-rank ones. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Fix compile errors if CONFIG_SYS_DPAA_QBMAN isn't setKumar Gala2011-07-111-0/+2
| | | | | | | | | | | Add ifdef protection for qp_info and liodn associated with Q/BMan. Also rearrange setting of _tbl_sz variables to utilize existing ifdef protection for things like FMAN. Also add protection around setup_portals() call in corenet_ds board code. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Fix compile errors if CONFIG_SYS_{B,Q}MAN_MEM_PHYS aren't setKumar Gala2011-07-112-0/+8
| | | | | | | | Add ifdef protection in LAW & TLB code to handle the case in which CONFIG_SYS_BMAN_MEM_PHYS or CONFIG_SYS_QMAN_MEM_PHYS arent defined for a build. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc: Add P3041DS/P5020DS board support (uses corenet_ds code)Kumar Gala2011-04-276-7/+87
| | | | | | | | | | | | | | | | The P3041DS & P5020DS boards are almost identical (except for the processor in them). Additionally they are based on the P4080DS board design so we use the some board code for all 3 boards. Some ngPIXIS (FPGA) registers where reserved on P4080DS and now have meaning on P3041DS/P5020DS. We utilize some of these for SERDES clock configuration. Additionally, the P3041DS/P5020DS support NAND. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Shaohui Xie <b21989@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add PBL boot from SPI flash support on P4080DSShaohui Xie2011-04-101-1/+11
| | | | | | | | | | | | | PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as 1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from CPC after PBL completes RCW and PBI phases. Signed-off-by: Chunhe Lan <b25806@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Shaohui Xie <b21989@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
OpenPOWER on IntegriCloud