diff options
Diffstat (limited to 'include/configs/motionpro.h')
| -rw-r--r-- | include/configs/motionpro.h | 168 |
1 files changed, 143 insertions, 25 deletions
diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h index 5328e8d6b1..e3899a5ab4 100644 --- a/include/configs/motionpro.h +++ b/include/configs/motionpro.h @@ -26,12 +26,10 @@ #ifndef __CONFIG_H #define __CONFIG_H - /* * High Level Configuration Options */ - /* CPU and board */ #define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ #define CONFIG_MPC5200 1 /* More exactly a MPC5200 */ @@ -50,7 +48,14 @@ CFG_CMD_MII | \ CFG_CMD_BEDBUG | \ CFG_CMD_NET | \ - CFG_CMD_PING) + CFG_CMD_PING | \ + CFG_CMD_IDE | \ + CFG_CMD_FAT | \ + CFG_CMD_JFFS2 | \ + CFG_CMD_I2C | \ + CFG_CMD_DATE | \ + CFG_CMD_EEPROM | \ + CFG_CMD_DTT) /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include <cmd_confdefs.h> @@ -71,7 +76,7 @@ #define CONFIG_MPC5xxx_FEC 1 #define CONFIG_PHY_ADDR 0x2 #define CONFIG_PHY_TYPE 0x79c874 - +#define CONFIG_RESET_PHY_R 1 /* * Autobooting @@ -94,42 +99,51 @@ * Default environment settings */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "sdram_test=0\0" \ "netdev=eth0\0" \ "hostname=motionpro\0" \ "netmask=255.255.0.0\0" \ "ipaddr=192.168.160.22\0" \ "serverip=192.168.1.1\0" \ "gatewayip=192.168.1.1\0" \ - "kernel_addr=200000\0" \ + "console=ttyPSC0,115200\0" \ "u-boot_addr=100000\0" \ - "kernel_sector=20\0" \ - "kernel_size=1000\0" \ - "console=ttyS0,115200\0" \ + "kernel_addr=200000\0" \ + "fdt_addr=400000\0" \ + "ramdisk_addr=500000\0" \ + "multi_image_addr=800000\0" \ "rootpath=/opt/eldk-4.1/ppc_6xx\0" \ - "bootfile=/tftpboot/motionpro/uImage\0" \ "u-boot=/tftpboot/motionpro/u-boot.bin\0" \ - "load=tftp $(u-boot_addr) $(u-boot)\0" \ + "bootfile=/tftpboot/motionpro/uImage\0" \ + "fdt_file=/tftpboot/motionpro/motionpro.dtb\0" \ + "ramdisk_file=/tftpboot/motionpro/uRamdisk\0" \ + "multi_image_file=kernel+initrd+dtb.img\0" \ + "load=tftp ${u-boot_addr} ${u-boot}\0" \ "update=prot off fff00000 fff3ffff; era fff00000 fff3ffff; " \ - "cp.b $(u-boot_addr) fff00000 $(filesize);" \ + "cp.b ${u-boot_addr} fff00000 ${filesize};" \ "prot on fff00000 fff3ffff\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs $(bootargs) console=$(console) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):" \ - "$(netmask):$(hostname):$(netdev):off panic=1\0" \ - "flash_nfs=run nfsargs addip;bootm $(kernel_addr)\0" \ - "flash_self=run ramargs addip;bootm $(kernel_addr) " \ - "$(ramdisk_addr)\0" \ - "net_nfs=tftp $(kernel_addr) $(bootfile); run nfsargs addip; " \ - "bootm $(kernel_addr)\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$(serverip):$(rootpath)\0" \ - "fstype=ext3\0" \ - "fatargs=setenv bootargs init=/linuxrc rw\0" \ + "nfsroot=${serverip}:${rootpath}\0" \ + "fat_args=setenv bootargs rw\0" \ + "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:" \ + "${netmask}:${hostname}:${netdev}:off panic=1 " \ + "console=${console}\0" \ + "net_nfs=tftp ${kernel_addr} ${bootfile}; " \ + "tftp ${fdt_addr} ${fdt_file}; run nfsargs addip; " \ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "net_self=tftp ${kernel_addr} ${bootfile}; " \ + "tftp ${fdt_addr} ${fdt_file}; " \ + "tftp ${ramdisk_addr} ${ramdisk_file}; " \ + "run ramargs addip; " \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ + "fat_multi=run fat_args addip; fatload ide 0:1 " \ + "${multi_image_addr} ${multi_image_file}; " \ + "bootm ${multi_image_addr}\0" \ "" #define CONFIG_BOOTCOMMAND "run net_nfs" - /* * do board-specific init */ @@ -148,6 +162,12 @@ /* + * Set IPB speed to 100MHz + */ +#define CFG_IPBCLK_EQUALS_XLBCLK + + +/* * Memory map */ /* @@ -243,6 +263,84 @@ #define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */ #define CONFIG_FLASH_16BIT /* Flash is 16-bit */ +/* + * MTD configuration + */ +#define CONFIG_JFFS2_CMDLINE +#define MTDIDS_DEFAULT "nor0=motionpro-0" +#define MTDPARTS_DEFAULT "mtdparts=motionpro-0:" \ + "13m(fs),2m(kernel),256k(uboot)," \ + "64k(env),64k(redund_env),64k(dtb)," \ + "-(user_data)" + +/* + * IDE/ATA configuration + */ +#define CFG_ATA_BASE_ADDR MPC5XXX_ATA +#define CFG_IDE_MAXBUS 1 +#define CFG_IDE_MAXDEVICE 1 +#define CONFIG_IDE_PREINIT + +#define CFG_ATA_DATA_OFFSET 0x0060 +#define CFG_ATA_REG_OFFSET CFG_ATA_DATA_OFFSET +#define CFG_ATA_STRIDE 4 +#define CONFIG_DOS_PARTITION + + +/* + * I2C configuration + */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CFG_I2C_MODULE 2 /* select I2C module #2 */ +#define CFG_I2C_SPEED 100000 /* 100 kHz */ +#define CFG_I2C_SLAVE 0x7F + + +/* + * EEPROM configuration + */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_EEPROM_PAGE_WRITE_ENABLE 1 /* DTT driver needs this */ +#define CFG_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */ +#define CFG_I2C_MULTI_EEPROMS 1 /* 2 EEPROMs (addr:50,52) */ + + +/* + * RTC configuration + */ +#define CONFIG_RTC_DS1337 1 +#define CFG_I2C_RTC_ADDR 0x68 + + +/* + * Status LED configuration + */ +#define CONFIG_STATUS_LED /* Status LED enabled */ +#define CONFIG_BOARD_SPECIFIC_LED + +#define ENABLE_GPIO_OUT 0x00000024 +#define LED_ON 0x00000010 + +#ifndef __ASSEMBLY__ +/* + * In case of Motion-PRO, a LED is identified by its corresponding + * GPT Enable and Mode Select Register. + */ +typedef volatile unsigned long * led_id_t; + +extern void __led_init(led_id_t id, int state); +extern void __led_toggle(led_id_t id); +extern void __led_set(led_id_t id, int state); +#endif /* __ASSEMBLY__ */ + + +/* + * Temperature sensor + */ +#define CONFIG_DTT_LM75 1 +#define CONFIG_DTT_SENSORS { 0x49 } + /* * Environment settings @@ -253,6 +351,9 @@ #define CFG_ENV_SIZE 0x1000 #define CFG_ENV_SECT_SIZE 0x10000 +/* Configuration of redundant environment */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) /* * Pin multiplexing configuration @@ -270,11 +371,17 @@ /* + * Motion-PRO's CPLD revision control register + */ +#define CPLD_REV_REGISTER (CFG_CS2_START + 0x06) + + +/* * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ @@ -302,4 +409,15 @@ /* Not needed for MPC 5xxx U-Boot, but used by tools/updater */ #define CFG_RESET_ADDRESS 0xfff00100 +/* pass open firmware flat tree */ +#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_BOARD_SETUP 1 + +/* maximum size of the flat tree (8K) */ +#define OF_FLAT_TREE_MAX_SIZE 8192 +#define OF_CPU "PowerPC,5200@0" +#define OF_SOC "soc5200@f0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" + #endif /* __CONFIG_H */ |
