diff options
Diffstat (limited to 'doc/device-tree-bindings')
| -rw-r--r-- | doc/device-tree-bindings/clock/rockchip,rk3188-cru.txt | 61 | ||||
| -rw-r--r-- | doc/device-tree-bindings/clock/rockchip,rk3288-cru.txt | 61 | ||||
| -rw-r--r-- | doc/device-tree-bindings/clock/rockchip,rk3288-dmc.txt | 155 | ||||
| -rw-r--r-- | doc/device-tree-bindings/clock/rockchip.txt | 77 | ||||
| -rw-r--r-- | doc/device-tree-bindings/pinctrl/rockchip,pinctrl.txt | 157 | ||||
| -rw-r--r-- | doc/device-tree-bindings/thermal/rockchip-thermal.txt | 68 |
6 files changed, 579 insertions, 0 deletions
diff --git a/doc/device-tree-bindings/clock/rockchip,rk3188-cru.txt b/doc/device-tree-bindings/clock/rockchip,rk3188-cru.txt new file mode 100644 index 0000000000..0c2bf5eba4 --- /dev/null +++ b/doc/device-tree-bindings/clock/rockchip,rk3188-cru.txt @@ -0,0 +1,61 @@ +* Rockchip RK3188/RK3066 Clock and Reset Unit + +The RK3188/RK3066 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3188-cru", "rockchip,rk3188a-cru" or + "rockchip,rk3066a-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3188-cru.h and +dt-bindings/clock/rk3066-cru.h headers and can be used in device tree sources. +Similar macros exist for the reset sources in these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "xin27m" - 27mhz crystal input on rk3066 - optional, + - "ext_hsadc" - external HSADC clock - optional, + - "ext_cif0" - external camera clock - optional, + - "ext_rmii" - external RMII clock - optional, + - "ext_jtag" - externalJTAG clock - optional + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3188-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10124000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10124000 0x400>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/doc/device-tree-bindings/clock/rockchip,rk3288-cru.txt b/doc/device-tree-bindings/clock/rockchip,rk3288-cru.txt new file mode 100644 index 0000000000..c9fbb76573 --- /dev/null +++ b/doc/device-tree-bindings/clock/rockchip,rk3288-cru.txt @@ -0,0 +1,61 @@ +* Rockchip RK3288 Clock and Reset Unit + +The RK3288 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3288-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3288-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "ext_i2s" - external I2S clock - optional, + - "ext_hsadc" - external HSADC clock - optional, + - "ext_edp_24m" - external display port clock - optional, + - "ext_vip" - external VIP clock - optional, + - "ext_isp" - external ISP clock - optional, + - "ext_jtag" - external JTAG clock - optional + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3188-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10124000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10124000 0x400>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/doc/device-tree-bindings/clock/rockchip,rk3288-dmc.txt b/doc/device-tree-bindings/clock/rockchip,rk3288-dmc.txt new file mode 100644 index 0000000000..2ca9db70a9 --- /dev/null +++ b/doc/device-tree-bindings/clock/rockchip,rk3288-dmc.txt @@ -0,0 +1,155 @@ +Rockchip Dynamic Memory Controller Driver +Required properties: +- compatible: "rockchip,rk3288-dmc", "syscon" +- rockchip,cru: this driver should access cru regs, so need get cru here +- rockchip,grf: this driver should access grf regs, so need get grf here +- rockchip,pmu: this driver should access pmu regs, so need get pmu here +- rockchip,sgrf: this driver should access sgrf regs, so need get sgrf here +- rockchip,noc: this driver should access noc regs, so need get noc here +- reg: dynamic ram protocol controller(PCTL) address and phy controller(PHYCTL) address +- clock: must include clock specifiers corresponding to entries in the clock-names property. +- clock-output-names: from common clock binding to override the default output clock name + Must contain + pclk_ddrupctl0: support clock for access protocol controller registers of channel 0 + pclk_publ0: support clock for access phy controller registers of channel 0 + pclk_ddrupctl1: support clock for access protocol controller registers of channel 1 + pclk_publ1: support clock for access phy controller registers of channel 1 + arm_clk: for get arm frequency +-logic-supply: this driver should adjust VDD_LOGIC according to dmc frequency, so need get logic-supply here +-timings: + Must contain + rockchip,odt-disable-freq: if ddr clock frequency low than odt-disable-freq,this driver should disable DDR ODT + rockchip,dll-disable-freq: if ddr clock frequency low than dll-disable-freq,this driver should disable DDR DLL + rockchip,sr-enable-freq: if ddr clock frequency high than sr-enable-freq,this driver should enable the automatic self refresh function + rockchip,pd-enable-freq: if ddr clock frequency high than pd-enable-freq,this driver should enable the automatic power down function + rockchip,auto-self-refresh-cnt: Self Refresh idle period. Memories are placed into Self-Refresh mode if the NIF is idle in Access state for auto-self-refresh-cnt * 32 * n_clk cycles.The automatic self refresh function is disabled when auto-self-refresh-cnt=0. + rockchip,auto-power-down-cnt: Power-down idle period. Memories are placed into power-down mode if the NIF is idle for auto-power-down-cnt n_clk cycles.The automatic power down function is disabled when auto-power-down-cnt=0. + rockchip,ddr-speed-bin: DDR3 type,AC timing parameters from the memory data-sheet + 0.DDR3_800D (5-5-5) + 1.DDR3_800E (6-6-6) + 2.DDR3_1066E (6-6-6) + 3.DDR3_1066F (7-7-7) + 4.DDR3_1066G (8-8-8) + 5.DDR3_1333F (7-7-7) + 6.DDR3_1333G (8-8-8) + 7.DDR3_1333H (9-9-9) + 8.DDR3_1333J (10-10-10) + 9.DDR3_1600G (8-8-8) + 10.DDR3_1600H (9-9-9) + 11.DDR3_1600J (10-10-10) + 12.DDR3_1600K (11-11-11) + 13.DDR3_1866J (10-10-10) + 14.DDR3_1866K (11-11-11) + 15.DDR3_1866L (12-12-12) + 16.DDR3_1866M (13-13-13) + 17.DDR3_2133K (11-11-11) + 18.DDR3_2133L (12-12-12) + 19.DDR3_2133M (13-13-13) + 20.DDR3_2133N (14-14-14) + 21.DDR3_DEFAULT + rockchip,trcd: tRCD,AC timing parameters from the memory data-sheet + rockchip,trp: tRP,AC timing parameters from the memory data-sheet +-rockchip,num-channels: number of SDRAM channels (1 or 2) +-rockchip,pctl-timing: parameters for the SDRAM setup, in this order: + togcnt1u + tinit + trsth + togcnt100n + trefi + tmrd + trfc + trp + trtw + tal + tcl + tcwl + tras + trc + trcd + trrd + trtp + twr + twtr + texsr + txp + txpdll + tzqcs + tzqcsi + tdqs + tcksre + tcksrx + tcke + tmod + trstl + tzqcl + tmrr + tckesr + tdpd +-rockchip,phy-timing: PHY timing information in this order: + dtpr0 + dtpr1 + dtpr2 + mr0..mr3 +-rockchip,sdram-channel: SDRAM channel information, each 8 bits. Both channels +will be set up the same. The parameters are in this order: + rank + col + bk + bw + dbw + row_3_4 + cs0_row + cs1_row +- rockchip,sdram-params: SDRAM base parameters, in this order: + NOC timing - value for ddrtiming register + NOC activate - value for activate register + ddrconf - value for ddrconf register + DDR frequency in MHz + DRAM type (3=DDR3, 6=LPDDR3) + stride - stride value for soc_con2 register + odt - 1 to enable DDR ODT, 0 to disable + +Example: + dmc: dmc@ff610000 { + compatible = "rockchip,rk3288-dmc", "syscon"; + rockchip,cru = <&cru>; + rockchip,grf = <&grf>; + rockchip,pmu = <&pmu>; + rockchip,sgrf = <&sgrf>; + rockchip,noc = <&noc>; + reg = <0xff610000 0x3fc + 0xff620000 0x294 + 0xff630000 0x3fc + 0xff640000 0x294>; + clocks = <&cru PCLK_DDRUPCTL0>, <&cru PCLK_PUBL0>, + <&cru PCLK_DDRUPCTL1>, <&cru PCLK_PUBL1>, + <&cru ARMCLK>; + clock-names = "pclk_ddrupctl0", "pclk_publ0", + "pclk_ddrupctl1", "pclk_publ1", + "arm_clk"; + }; + + &dmc { + logic-supply = <&vdd_logic>; + timings { + rockchip,odt-disable-freq = <333000000>; + rockchip,dll-disable-freq = <333000000>; + rockchip,sr-enable-freq = <333000000>; + rockchip,pd-enable-freq = <666000000>; + rockchip,auto-self-refresh-cnt = <0>; + rockchip,auto-power-down-cnt = <64>; + rockchip,ddr-speed-bin = <21>; + rockchip,trcd = <10>; + rockchip,trp = <10>; + }; + rockchip,num-channels = <2>; + rockchip,pctl-timing = <0x29a 0x1f4 0xc8 0x42 0x4e 0x4 0xea 0xa + 0x5 0x0 0xa 0x7 0x19 0x24 0xa 0x7 + 0x5 0xa 0x5 0x200 0x5 0x10 0x40 0x0 + 0x1 0x7 0x7 0x4 0xc 0x43 0x100 0x0 + 0x5 0x0>; + rockchip,phy-timing = <0x48f9aab4 0xea0910 0x1002c200 + 0xa60 0x40 0x10 0x0>; + rockchip,sdram-channel = /bits/ 8 <0x1 0xa 0x3 0x2 0x1 0x0 0xf 0xf>; + rockchip,sdram-params = <0x30B25564 0x627 3 666000000 3 9 1>; + }; diff --git a/doc/device-tree-bindings/clock/rockchip.txt b/doc/device-tree-bindings/clock/rockchip.txt new file mode 100644 index 0000000000..22f6769e5d --- /dev/null +++ b/doc/device-tree-bindings/clock/rockchip.txt @@ -0,0 +1,77 @@ +Device Tree Clock bindings for arch-rockchip + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +== Gate clocks == + +These bindings are deprecated! +Please use the soc specific CRU bindings instead. + +The gate registers form a continuos block which makes the dt node +structure a matter of taste, as either all gates can be put into +one gate clock spanning all registers or they can be divided into +the 10 individual gates containing 16 clocks each. +The code supports both approaches. + +Required properties: +- compatible : "rockchip,rk2928-gate-clk" +- reg : shall be the control register address(es) for the clock. +- #clock-cells : from common clock binding; shall be set to 1 +- clock-output-names : the corresponding gate names that the clock controls +- clocks : should contain the parent clock for each individual gate, + therefore the number of clocks elements should match the number of + clock-output-names + +Example using multiple gate clocks: + + clk_gates0: gate-clk@200000d0 { + compatible = "rockchip,rk2928-gate-clk"; + reg = <0x200000d0 0x4>; + clocks = <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>; + + clock-output-names = + "gate_core_periph", "gate_cpu_gpll", + "gate_ddrphy", "gate_aclk_cpu", + "gate_hclk_cpu", "gate_pclk_cpu", + "gate_atclk_cpu", "gate_i2s0", + "gate_i2s0_frac", "gate_i2s1", + "gate_i2s1_frac", "gate_i2s2", + "gate_i2s2_frac", "gate_spdif", + "gate_spdif_frac", "gate_testclk"; + + #clock-cells = <1>; + }; + + clk_gates1: gate-clk@200000d4 { + compatible = "rockchip,rk2928-gate-clk"; + reg = <0x200000d4 0x4>; + clocks = <&xin24m>, <&xin24m>, + <&xin24m>, <&dummy>, + <&dummy>, <&xin24m>, + <&xin24m>, <&dummy>, + <&xin24m>, <&dummy>, + <&xin24m>, <&dummy>, + <&xin24m>, <&dummy>, + <&xin24m>, <&dummy>; + + clock-output-names = + "gate_timer0", "gate_timer1", + "gate_timer2", "gate_jtag", + "gate_aclk_lcdc1_src", "gate_otgphy0", + "gate_otgphy1", "gate_ddr_gpll", + "gate_uart0", "gate_frac_uart0", + "gate_uart1", "gate_frac_uart1", + "gate_uart2", "gate_frac_uart2", + "gate_uart3", "gate_frac_uart3"; + + #clock-cells = <1>; + }; diff --git a/doc/device-tree-bindings/pinctrl/rockchip,pinctrl.txt b/doc/device-tree-bindings/pinctrl/rockchip,pinctrl.txt new file mode 100644 index 0000000000..388b213249 --- /dev/null +++ b/doc/device-tree-bindings/pinctrl/rockchip,pinctrl.txt @@ -0,0 +1,157 @@ +* Rockchip Pinmux Controller + +The Rockchip Pinmux Controller, enables the IC +to share one PAD to several functional blocks. The sharing is done by +multiplexing the PAD input/output signals. For each PAD there are several +muxing options with option 0 being the use as a GPIO. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The Rockchip pin configuration node is a node of a group of pins which can be +used for a specific device or function. This node represents both mux and +config of the pins in that group. The 'pins' selects the function mode(also +named pin mode) this pin can work on and the 'config' configures various pad +settings such as pull-up, etc. + +The pins are grouped into up to 5 individual pin banks which need to be +defined as gpio sub-nodes of the pinmux controller. + +Required properties for iomux controller: + - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl" + "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl" + "rockchip,rk3288-pinctrl" + - rockchip,grf: phandle referencing a syscon providing the + "general register files" + +Optional properties for iomux controller: + - rockchip,pmu: phandle referencing a syscon providing the pmu registers + as some SoCs carry parts of the iomux controller registers there. + Required for at least rk3188 and rk3288. + +Deprecated properties for iomux controller: + - reg: first element is the general register space of the iomux controller + It should be large enough to contain also separate pull registers. + second element is the separate pull register space of the rk3188. + Use rockchip,grf and rockchip,pmu described above instead. + +Required properties for gpio sub nodes: + - compatible: "rockchip,gpio-bank" + - reg: register of the gpio bank (different than the iomux registerset) + - interrupts: base interrupt of the gpio bank in the interrupt controller + - clocks: clock that drives this bank + - gpio-controller: identifies the node as a gpio controller and pin bank. + - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO + binding is used, the amount of cells must be specified as 2. See generic + GPIO binding documentation for description of particular cells. + - interrupt-controller: identifies the controller node as interrupt-parent. + - #interrupt-cells: the value of this property should be 2 and the interrupt + cells should use the standard two-cell scheme described in + bindings/interrupt-controller/interrupts.txt + +Deprecated properties for gpio sub nodes: + - compatible: "rockchip,rk3188-gpio-bank0" + - reg: second element: separate pull register for rk3188 bank0, use + rockchip,pmu described above instead + +Required properties for pin configuration node: + - rockchip,pins: 3 integers array, represents a group of pins mux and config + setting. The format is rockchip,pins = <PIN_BANK PIN_BANK_IDX MUX &phandle>. + The MUX 0 means gpio and MUX 1 to N mean the specific device function. + The phandle of a node containing the generic pinconfig options + to use, as described in pinctrl-bindings.txt in this directory. + +Examples: + +#include <dt-bindings/pinctrl/rockchip.h> + +... + +pinctrl@20008000 { + compatible = "rockchip,rk3066a-pinctrl"; + rockchip,grf = <&grf>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gpio0: gpio0@20034000 { + compatible = "rockchip,gpio-bank"; + reg = <0x20034000 0x100>; + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_gates8 9>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + ... + + pcfg_pull_default: pcfg_pull_default { + bias-pull-pin-default + }; + + uart2 { + uart2_xfer: uart2-xfer { + rockchip,pins = <RK_GPIO1 8 1 &pcfg_pull_default>, + <RK_GPIO1 9 1 &pcfg_pull_default>; + }; + }; +}; + +uart2: serial@20064000 { + compatible = "snps,dw-apb-uart"; + reg = <0x20064000 0x400>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&mux_uart2>; + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&uart2_xfer>; +}; + +Example for rk3188: + + pinctrl@20008000 { + compatible = "rockchip,rk3188-pinctrl"; + rockchip,grf = <&grf>; + rockchip,pmu = <&pmu>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gpio0: gpio0@0x2000a000 { + compatible = "rockchip,rk3188-gpio-bank0"; + reg = <0x2000a000 0x100>; + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_gates8 9>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio1@0x2003c000 { + compatible = "rockchip,gpio-bank"; + reg = <0x2003c000 0x100>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_gates8 10>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + ... + + }; diff --git a/doc/device-tree-bindings/thermal/rockchip-thermal.txt b/doc/device-tree-bindings/thermal/rockchip-thermal.txt new file mode 100644 index 0000000000..ef802de495 --- /dev/null +++ b/doc/device-tree-bindings/thermal/rockchip-thermal.txt @@ -0,0 +1,68 @@ +* Temperature Sensor ADC (TSADC) on rockchip SoCs + +Required properties: +- compatible : "rockchip,rk3288-tsadc" +- reg : physical base address of the controller and length of memory mapped + region. +- interrupts : The interrupt number to the cpu. The interrupt specifier format + depends on the interrupt controller. +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Shall be "tsadc" for the converter-clock, and "apb_pclk" for + the peripheral clock. +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the name "tsadc-apb". +- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description. +- rockchip,hw-tshut-temp : The hardware-controlled shutdown temperature value. +- rockchip,hw-tshut-mode : The hardware-controlled shutdown mode 0:CRU 1:GPIO. +- rockchip,hw-tshut-polarity : The hardware-controlled active polarity 0:LOW + 1:HIGH. + +Exiample: +tsadc: tsadc@ff280000 { + compatible = "rockchip,rk3288-tsadc"; + reg = <0xff280000 0x100>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>; + clock-names = "tsadc", "apb_pclk"; + resets = <&cru SRST_TSADC>; + reset-names = "tsadc-apb"; + pinctrl-names = "default"; + pinctrl-0 = <&otp_out>; + #thermal-sensor-cells = <1>; + rockchip,hw-tshut-temp = <95000>; + rockchip,hw-tshut-mode = <0>; + rockchip,hw-tshut-polarity = <0>; +}; + +Example: referring to thermal sensors: +thermal-zones { + cpu_thermal: cpu_thermal { + polling-delay-passive = <1000>; /* milliseconds */ + polling-delay = <5000>; /* milliseconds */ + + /* sensor ID */ + thermal-sensors = <&tsadc 1>; + + trips { + cpu_alert0: cpu_alert { + temperature = <70000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_crit: cpu_crit { + temperature = <90000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu_alert0>; + cooling-device = + <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; +}; |
