rockchip: Bring in RK3288 device tree file includes and bindings

Bring in required device tree files from Linux. Since mainline Linux is
somewhat behind, use the files from the Chromium tree. We can re-sync once
further code is acccepted upstream.

Signed-off-by: Simon Glass <sjg@chromium.org>

6 files changed, 579 insertions, 0 deletions

diff --git a/doc/device-tree-bindings/clock/rockchip,rk3188-cru.txt b/doc/device-tree-bindings/clock/rockchip,rk3188-cru.txt
new file mode 100644
index 0000000000..0c2bf5eba4
--- /dev/null
+++ b/doc/device-tree-bindings/clock/rockchip,rk3188-cru.txt
@@ -0,0 +1,61 @@
+* Rockchip RK3188/RK3066 Clock and Reset Unit
+
+The RK3188/RK3066 clock controller generates and supplies clock to various
+controllers within the SoC and also implements a reset controller for SoC
+peripherals.
+
+Required Properties:
+
+- compatible: should be "rockchip,rk3188-cru", "rockchip,rk3188a-cru" or
+			"rockchip,rk3066a-cru"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- #clock-cells: should be 1.
+- #reset-cells: should be 1.
+
+Optional Properties:
+
+- rockchip,grf: phandle to the syscon managing the "general register files"
+  If missing pll rates are not changable, due to the missing pll lock status.
+
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume. All available clocks are defined as
+preprocessor macros in the dt-bindings/clock/rk3188-cru.h and
+dt-bindings/clock/rk3066-cru.h headers and can be used in device tree sources.
+Similar macros exist for the reset sources in these files.
+
+External clocks:
+
+There are several clocks that are generated outside the SoC. It is expected
+that they are defined using standard clock bindings with following
+clock-output-names:
+ - "xin24m" - crystal input - required,
+ - "xin32k" - rtc clock - optional,
+ - "xin27m" - 27mhz crystal input on rk3066 - optional,
+ - "ext_hsadc" - external HSADC clock - optional,
+ - "ext_cif0" - external camera clock - optional,
+ - "ext_rmii" - external RMII clock - optional,
+ - "ext_jtag" - externalJTAG clock - optional
+
+Example: Clock controller node:
+
+	cru: cru@20000000 {
+		compatible = "rockchip,rk3188-cru";
+		reg = <0x20000000 0x1000>;
+		rockchip,grf = <&grf>;
+
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+	};
+
+Example: UART controller node that consumes the clock generated by the clock
+  controller:
+
+	uart0: serial@10124000 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x10124000 0x400>;
+		interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <1>;
+		clocks = <&cru SCLK_UART0>;
+	};
diff --git a/doc/device-tree-bindings/clock/rockchip,rk3288-cru.txt b/doc/device-tree-bindings/clock/rockchip,rk3288-cru.txt
new file mode 100644
index 0000000000..c9fbb76573
--- /dev/null
+++ b/doc/device-tree-bindings/clock/rockchip,rk3288-cru.txt
@@ -0,0 +1,61 @@
+* Rockchip RK3288 Clock and Reset Unit
+
+The RK3288 clock controller generates and supplies clock to various
+controllers within the SoC and also implements a reset controller for SoC
+peripherals.
+
+Required Properties:
+
+- compatible: should be "rockchip,rk3288-cru"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- #clock-cells: should be 1.
+- #reset-cells: should be 1.
+
+Optional Properties:
+
+- rockchip,grf: phandle to the syscon managing the "general register files"
+  If missing pll rates are not changable, due to the missing pll lock status.
+
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume. All available clocks are defined as
+preprocessor macros in the dt-bindings/clock/rk3288-cru.h headers and can be
+used in device tree sources. Similar macros exist for the reset sources in
+these files.
+
+External clocks:
+
+There are several clocks that are generated outside the SoC. It is expected
+that they are defined using standard clock bindings with following
+clock-output-names:
+ - "xin24m" - crystal input - required,
+ - "xin32k" - rtc clock - optional,
+ - "ext_i2s" - external I2S clock - optional,
+ - "ext_hsadc" - external HSADC clock - optional,
+ - "ext_edp_24m" - external display port clock - optional,
+ - "ext_vip" - external VIP clock - optional,
+ - "ext_isp" - external ISP clock - optional,
+ - "ext_jtag" - external JTAG clock - optional
+
+Example: Clock controller node:
+
+	cru: cru@20000000 {
+		compatible = "rockchip,rk3188-cru";
+		reg = <0x20000000 0x1000>;
+		rockchip,grf = <&grf>;
+
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+	};
+
+Example: UART controller node that consumes the clock generated by the clock
+  controller:
+
+	uart0: serial@10124000 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x10124000 0x400>;
+		interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <1>;
+		clocks = <&cru SCLK_UART0>;
+	};
diff --git a/doc/device-tree-bindings/clock/rockchip,rk3288-dmc.txt b/doc/device-tree-bindings/clock/rockchip,rk3288-dmc.txt
new file mode 100644
index 0000000000..2ca9db70a9
--- /dev/null
+++ b/doc/device-tree-bindings/clock/rockchip,rk3288-dmc.txt
@@ -0,0 +1,155 @@
+Rockchip Dynamic Memory Controller Driver
+Required properties:
+- compatible: "rockchip,rk3288-dmc", "syscon"
+- rockchip,cru: this driver should access cru regs, so need get cru here
+- rockchip,grf: this driver should access grf regs, so need get grf here
+- rockchip,pmu: this driver should access pmu regs, so need get pmu here
+- rockchip,sgrf: this driver should access sgrf regs, so need get sgrf here
+- rockchip,noc: this driver should access noc regs, so need get noc here
+- reg: dynamic ram protocol controller(PCTL) address and phy controller(PHYCTL) address
+- clock: must include clock specifiers corresponding to entries in the clock-names property.
+- clock-output-names: from common clock binding to override the default output clock name
+    Must contain
+      pclk_ddrupctl0: support clock for access protocol controller registers of channel 0
+      pclk_publ0: support clock for access phy controller registers of channel 0
+      pclk_ddrupctl1: support clock for access protocol controller registers of channel 1
+      pclk_publ1: support clock for access phy controller registers of channel 1
+      arm_clk: for get arm frequency
+-logic-supply: this driver should adjust VDD_LOGIC according to dmc frequency, so need get logic-supply here
+-timings:
+    Must contain
+      rockchip,odt-disable-freq: if ddr clock frequency low than odt-disable-freq,this driver should disable DDR ODT
+      rockchip,dll-disable-freq: if ddr clock frequency low than dll-disable-freq,this driver should disable DDR DLL
+      rockchip,sr-enable-freq: if ddr clock frequency high than sr-enable-freq,this driver should enable the automatic self refresh function
+      rockchip,pd-enable-freq: if ddr clock frequency high than pd-enable-freq,this driver should enable the automatic power down function
+      rockchip,auto-self-refresh-cnt: Self Refresh idle period. Memories are placed into Self-Refresh mode if the NIF is idle in Access state for auto-self-refresh-cnt * 32 * n_clk cycles.The automatic self refresh function is disabled when auto-self-refresh-cnt=0.
+      rockchip,auto-power-down-cnt: Power-down idle period. Memories are placed into power-down mode if the NIF is idle for auto-power-down-cnt n_clk cycles.The automatic power down function is disabled when auto-power-down-cnt=0.
+      rockchip,ddr-speed-bin: DDR3 type,AC timing parameters from the memory data-sheet
+        0.DDR3_800D (5-5-5)
+        1.DDR3_800E (6-6-6)
+        2.DDR3_1066E (6-6-6)
+        3.DDR3_1066F (7-7-7)
+        4.DDR3_1066G (8-8-8)
+        5.DDR3_1333F (7-7-7)
+        6.DDR3_1333G (8-8-8)
+        7.DDR3_1333H (9-9-9)
+        8.DDR3_1333J (10-10-10)
+        9.DDR3_1600G (8-8-8)
+        10.DDR3_1600H (9-9-9)
+        11.DDR3_1600J (10-10-10)
+        12.DDR3_1600K (11-11-11)
+        13.DDR3_1866J (10-10-10)
+        14.DDR3_1866K (11-11-11)
+        15.DDR3_1866L (12-12-12)
+        16.DDR3_1866M (13-13-13)
+        17.DDR3_2133K (11-11-11)
+        18.DDR3_2133L (12-12-12)
+        19.DDR3_2133M (13-13-13)
+        20.DDR3_2133N (14-14-14)
+        21.DDR3_DEFAULT
+      rockchip,trcd: tRCD,AC timing parameters from the memory data-sheet
+      rockchip,trp: tRP,AC timing parameters from the memory data-sheet
+-rockchip,num-channels: number of SDRAM channels (1 or 2)
+-rockchip,pctl-timing: parameters for the SDRAM setup, in this order:
+	togcnt1u
+	tinit
+	trsth
+	togcnt100n
+	trefi
+	tmrd
+	trfc
+	trp
+	trtw
+	tal
+	tcl
+	tcwl
+	tras
+	trc
+	trcd
+	trrd
+	trtp
+	twr
+	twtr
+	texsr
+	txp
+	txpdll
+	tzqcs
+	tzqcsi
+	tdqs
+	tcksre
+	tcksrx
+	tcke
+	tmod
+	trstl
+	tzqcl
+	tmrr
+	tckesr
+	tdpd
+-rockchip,phy-timing: PHY timing information in this order:
+	dtpr0
+	dtpr1
+	dtpr2
+	mr0..mr3
+-rockchip,sdram-channel: SDRAM channel information, each 8 bits. Both channels
+will be set up the same. The parameters are in this order:
+	rank
+	col
+	bk
+	bw
+	dbw
+	row_3_4
+	cs0_row
+	cs1_row
+- rockchip,sdram-params: SDRAM base parameters, in this order:
+	NOC timing	- value for ddrtiming register
+	NOC activate	- value for activate register
+	ddrconf		- value for ddrconf register
+	DDR frequency in MHz
+	DRAM type (3=DDR3, 6=LPDDR3)
+	stride		- stride value for soc_con2 register
+	odt             - 1 to enable DDR ODT, 0 to disable
+
+Example:
+	dmc: dmc@ff610000 {
+		compatible = "rockchip,rk3288-dmc", "syscon";
+		rockchip,cru = <&cru>;
+		rockchip,grf = <&grf>;
+		rockchip,pmu = <&pmu>;
+		rockchip,sgrf = <&sgrf>;
+		rockchip,noc = <&noc>;
+		reg = <0xff610000 0x3fc
+		       0xff620000 0x294
+		       0xff630000 0x3fc
+		       0xff640000 0x294>;
+		clocks = <&cru PCLK_DDRUPCTL0>, <&cru PCLK_PUBL0>,
+			 <&cru PCLK_DDRUPCTL1>, <&cru PCLK_PUBL1>,
+			 <&cru ARMCLK>;
+		clock-names = "pclk_ddrupctl0", "pclk_publ0",
+			      "pclk_ddrupctl1", "pclk_publ1",
+			      "arm_clk";
+	};
+
+	&dmc {
+		logic-supply = <&vdd_logic>;
+		timings {
+			rockchip,odt-disable-freq = <333000000>;
+			rockchip,dll-disable-freq = <333000000>;
+			rockchip,sr-enable-freq = <333000000>;
+			rockchip,pd-enable-freq = <666000000>;
+			rockchip,auto-self-refresh-cnt = <0>;
+			rockchip,auto-power-down-cnt = <64>;
+			rockchip,ddr-speed-bin = <21>;
+			rockchip,trcd = <10>;
+			rockchip,trp = <10>;
+		};
+		rockchip,num-channels = <2>;
+		rockchip,pctl-timing = <0x29a 0x1f4 0xc8 0x42 0x4e 0x4 0xea 0xa
+			0x5 0x0 0xa 0x7 0x19 0x24 0xa 0x7
+			0x5 0xa 0x5 0x200 0x5 0x10 0x40 0x0
+			0x1 0x7 0x7 0x4 0xc 0x43 0x100 0x0
+			0x5 0x0>;
+		rockchip,phy-timing = <0x48f9aab4 0xea0910 0x1002c200
+			0xa60 0x40 0x10 0x0>;
+		rockchip,sdram-channel = /bits/ 8 <0x1 0xa 0x3 0x2 0x1 0x0 0xf 0xf>;
+		rockchip,sdram-params = <0x30B25564 0x627 3 666000000 3 9 1>;
+	};
diff --git a/doc/device-tree-bindings/clock/rockchip.txt b/doc/device-tree-bindings/clock/rockchip.txt
new file mode 100644
index 0000000000..22f6769e5d
--- /dev/null
+++ b/doc/device-tree-bindings/clock/rockchip.txt
@@ -0,0 +1,77 @@
+Device Tree Clock bindings for arch-rockchip
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+== Gate clocks ==
+
+These bindings are deprecated!
+Please use the soc specific CRU bindings instead.
+
+The gate registers form a continuos block which makes the dt node
+structure a matter of taste, as either all gates can be put into
+one gate clock spanning all registers or they can be divided into
+the 10 individual gates containing 16 clocks each.
+The code supports both approaches.
+
+Required properties:
+- compatible : "rockchip,rk2928-gate-clk"
+- reg : shall be the control register address(es) for the clock.
+- #clock-cells : from common clock binding; shall be set to 1
+- clock-output-names : the corresponding gate names that the clock controls
+- clocks : should contain the parent clock for each individual gate,
+  therefore the number of clocks elements should match the number of
+  clock-output-names
+
+Example using multiple gate clocks:
+
+		clk_gates0: gate-clk@200000d0 {
+			compatible = "rockchip,rk2928-gate-clk";
+			reg = <0x200000d0 0x4>;
+			clocks = <&dummy>, <&dummy>,
+				 <&dummy>, <&dummy>,
+				 <&dummy>, <&dummy>,
+				 <&dummy>, <&dummy>,
+				 <&dummy>, <&dummy>,
+				 <&dummy>, <&dummy>,
+				 <&dummy>, <&dummy>,
+				 <&dummy>, <&dummy>;
+
+			clock-output-names =
+				"gate_core_periph", "gate_cpu_gpll",
+				"gate_ddrphy", "gate_aclk_cpu",
+				"gate_hclk_cpu", "gate_pclk_cpu",
+				"gate_atclk_cpu", "gate_i2s0",
+				"gate_i2s0_frac", "gate_i2s1",
+				"gate_i2s1_frac", "gate_i2s2",
+				"gate_i2s2_frac", "gate_spdif",
+				"gate_spdif_frac", "gate_testclk";
+
+			#clock-cells = <1>;
+		};
+
+		clk_gates1: gate-clk@200000d4 {
+			compatible = "rockchip,rk2928-gate-clk";
+			reg = <0x200000d4 0x4>;
+			clocks = <&xin24m>, <&xin24m>,
+				 <&xin24m>, <&dummy>,
+				 <&dummy>, <&xin24m>,
+				 <&xin24m>, <&dummy>,
+				 <&xin24m>, <&dummy>,
+				 <&xin24m>, <&dummy>,
+				 <&xin24m>, <&dummy>,
+				 <&xin24m>, <&dummy>;
+
+			clock-output-names =
+				"gate_timer0", "gate_timer1",
+				"gate_timer2", "gate_jtag",
+				"gate_aclk_lcdc1_src", "gate_otgphy0",
+				"gate_otgphy1", "gate_ddr_gpll",
+				"gate_uart0", "gate_frac_uart0",
+				"gate_uart1", "gate_frac_uart1",
+				"gate_uart2", "gate_frac_uart2",
+				"gate_uart3", "gate_frac_uart3";
+
+			#clock-cells = <1>;
+		};
diff --git a/doc/device-tree-bindings/pinctrl/rockchip,pinctrl.txt b/doc/device-tree-bindings/pinctrl/rockchip,pinctrl.txt
new file mode 100644
index 0000000000..388b213249
--- /dev/null
+++ b/doc/device-tree-bindings/pinctrl/rockchip,pinctrl.txt
@@ -0,0 +1,157 @@
+* Rockchip Pinmux Controller
+
+The Rockchip Pinmux Controller, enables the IC
+to share one PAD to several functional blocks. The sharing is done by
+multiplexing the PAD input/output signals. For each PAD there are several
+muxing options with option 0 being the use as a GPIO.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The Rockchip pin configuration node is a node of a group of pins which can be
+used for a specific device or function. This node represents both mux and
+config of the pins in that group. The 'pins' selects the function mode(also
+named pin mode) this pin can work on and the 'config' configures various pad
+settings such as pull-up, etc.
+
+The pins are grouped into up to 5 individual pin banks which need to be
+defined as gpio sub-nodes of the pinmux controller.
+
+Required properties for iomux controller:
+  - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl"
+		       "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl"
+		       "rockchip,rk3288-pinctrl"
+  - rockchip,grf: phandle referencing a syscon providing the
+	 "general register files"
+
+Optional properties for iomux controller:
+  - rockchip,pmu: phandle referencing a syscon providing the pmu registers
+	 as some SoCs carry parts of the iomux controller registers there.
+	 Required for at least rk3188 and rk3288.
+
+Deprecated properties for iomux controller:
+  - reg: first element is the general register space of the iomux controller
+	 It should be large enough to contain also separate pull registers.
+	 second element is the separate pull register space of the rk3188.
+	 Use rockchip,grf and rockchip,pmu described above instead.
+
+Required properties for gpio sub nodes:
+  - compatible: "rockchip,gpio-bank"
+  - reg: register of the gpio bank (different than the iomux registerset)
+  - interrupts: base interrupt of the gpio bank in the interrupt controller
+  - clocks: clock that drives this bank
+  - gpio-controller: identifies the node as a gpio controller and pin bank.
+  - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
+    binding is used, the amount of cells must be specified as 2. See generic
+    GPIO binding documentation for description of particular cells.
+  - interrupt-controller: identifies the controller node as interrupt-parent.
+  - #interrupt-cells: the value of this property should be 2 and the interrupt
+    cells should use the standard two-cell scheme described in
+    bindings/interrupt-controller/interrupts.txt
+
+Deprecated properties for gpio sub nodes:
+  - compatible: "rockchip,rk3188-gpio-bank0"
+  - reg: second element: separate pull register for rk3188 bank0, use
+	 rockchip,pmu described above instead
+
+Required properties for pin configuration node:
+  - rockchip,pins: 3 integers array, represents a group of pins mux and config
+    setting. The format is rockchip,pins = <PIN_BANK PIN_BANK_IDX MUX &phandle>.
+    The MUX 0 means gpio and MUX 1 to N mean the specific device function.
+    The phandle of a node containing the generic pinconfig options
+    to use, as described in pinctrl-bindings.txt in this directory.
+
+Examples:
+
+#include <dt-bindings/pinctrl/rockchip.h>
+
+...
+
+pinctrl@20008000 {
+	compatible = "rockchip,rk3066a-pinctrl";
+	rockchip,grf = <&grf>;
+
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	gpio0: gpio0@20034000 {
+		compatible = "rockchip,gpio-bank";
+		reg = <0x20034000 0x100>;
+		interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_gates8 9>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	...
+
+	pcfg_pull_default: pcfg_pull_default {
+		bias-pull-pin-default
+	};
+
+	uart2 {
+		uart2_xfer: uart2-xfer {
+			rockchip,pins = <RK_GPIO1 8 1 &pcfg_pull_default>,
+					<RK_GPIO1 9 1 &pcfg_pull_default>;
+		};
+	};
+};
+
+uart2: serial@20064000 {
+	compatible = "snps,dw-apb-uart";
+	reg = <0x20064000 0x400>;
+	interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+	reg-shift = <2>;
+	reg-io-width = <1>;
+	clocks = <&mux_uart2>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_xfer>;
+};
+
+Example for rk3188:
+
+	pinctrl@20008000 {
+		compatible = "rockchip,rk3188-pinctrl";
+		rockchip,grf = <&grf>;
+		rockchip,pmu = <&pmu>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gpio0: gpio0@0x2000a000 {
+			compatible = "rockchip,rk3188-gpio-bank0";
+			reg = <0x2000a000 0x100>;
+			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_gates8 9>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio1: gpio1@0x2003c000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x2003c000 0x100>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_gates8 10>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		...
+
+	};
diff --git a/doc/device-tree-bindings/thermal/rockchip-thermal.txt b/doc/device-tree-bindings/thermal/rockchip-thermal.txt
new file mode 100644
index 0000000000..ef802de495
--- /dev/null
+++ b/doc/device-tree-bindings/thermal/rockchip-thermal.txt
@@ -0,0 +1,68 @@
+* Temperature Sensor ADC (TSADC) on rockchip SoCs
+
+Required properties:
+- compatible : "rockchip,rk3288-tsadc"
+- reg : physical base address of the controller and length of memory mapped
+	region.
+- interrupts : The interrupt number to the cpu. The interrupt specifier format
+	       depends on the interrupt controller.
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Shall be "tsadc" for the converter-clock, and "apb_pclk" for
+		the peripheral clock.
+- resets : Must contain an entry for each entry in reset-names.
+	   See ../reset/reset.txt for details.
+- reset-names : Must include the name "tsadc-apb".
+- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description.
+- rockchip,hw-tshut-temp : The hardware-controlled shutdown temperature value.
+- rockchip,hw-tshut-mode : The hardware-controlled shutdown mode 0:CRU 1:GPIO.
+- rockchip,hw-tshut-polarity : The hardware-controlled active polarity 0:LOW
+			       1:HIGH.
+
+Exiample:
+tsadc: tsadc@ff280000 {
+	compatible = "rockchip,rk3288-tsadc";
+	reg = <0xff280000 0x100>;
+	interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>;
+	clock-names = "tsadc", "apb_pclk";
+	resets = <&cru SRST_TSADC>;
+	reset-names = "tsadc-apb";
+	pinctrl-names = "default";
+	pinctrl-0 = <&otp_out>;
+	#thermal-sensor-cells = <1>;
+	rockchip,hw-tshut-temp = <95000>;
+	rockchip,hw-tshut-mode = <0>;
+	rockchip,hw-tshut-polarity = <0>;
+};
+
+Example: referring to thermal sensors:
+thermal-zones {
+	cpu_thermal: cpu_thermal {
+		polling-delay-passive = <1000>; /* milliseconds */
+		polling-delay = <5000>; /* milliseconds */
+
+		/* sensor	ID */
+		thermal-sensors = <&tsadc	1>;
+
+		trips {
+			cpu_alert0: cpu_alert {
+				temperature = <70000>; /* millicelsius */
+				hysteresis = <2000>; /* millicelsius */
+				type = "passive";
+			};
+			cpu_crit: cpu_crit {
+				temperature = <90000>; /* millicelsius */
+				hysteresis = <2000>; /* millicelsius */
+				type = "critical";
+			};
+		};
+
+		cooling-maps {
+			map0 {
+				trip = <&cpu_alert0>;
+				cooling-device =
+				    <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+};