diff options
Diffstat (limited to 'doc/README.mpc837xemds')
| -rw-r--r-- | doc/README.mpc837xemds | 104 |
1 files changed, 0 insertions, 104 deletions
diff --git a/doc/README.mpc837xemds b/doc/README.mpc837xemds deleted file mode 100644 index faf21c9ffb..0000000000 --- a/doc/README.mpc837xemds +++ /dev/null @@ -1,104 +0,0 @@ -Freescale MPC837xEMDS Board ------------------------------------------ -1. Board Switches and Jumpers -1.0 There are four Dual-In-Line Packages(DIP) Switches on MPC837xEMDS board - For some reason, the HW designers describe the switch settings - in terms of 0 and 1, and then map that to physical switches where - the label "On" refers to logic 0 and "Off" is logic 1. - - Switch bits are numbered 1 through, like, 4 6 8 or 10, but the - bits may contribute to signals that are numbered based at 0, - and some of those signals may be high-bit-number-0 too. Heed - well the names and labels and do not get confused. - - "Off" == 1 - "On" == 0 - - SW4[8] is the bit labeled 8 on Switch 4. - SW2[1:6] refers to bits labeled 1 through 6 in order on switch 2. - SW2[1:8]= 0000_0001 refers to bits labeled 1 through 7 is set as "On" - and bits labeled 8 is set as "Off". - -1.1 For the MPC837xEMDS Processor Board - - First, make sure the board default setting is consistent with the - document shipped with your board. Then apply the following setting: - SW3[1-8]= 0011_0000 (BOOTSEQ, ROMLOC setting) - SW4[1-8]= 0000_0110 (core PLL setting) - SW5[1-8]= 1001_1000 (system PLL, boot up from low end of flash) - SW6[1-8]= 0000_1000 (HRCW is read from NOR FLASH) - SW7[1-8]= 0110_1101 (TSEC1/2 interface setting - RGMII) - J3 2-3, TSEC1 LVDD1 with 2.5V - J6 2-3, TSEC2 LVDD2 with 2.5V - J9 2-3, CLKIN from osc on board - J10 removed, CS0 connect to NOR flash; when mounted, CS0 connect to NAND - J11 removed, Hardware Reset Configuration Word load from FLASH(NOR or NAND) - mounted, HRCW load from BCSR. - - on board Oscillator: 66M - -2. Memory Map - -2.1. The memory map should look pretty much like this: - - 0x0000_0000 0x7fff_ffff DDR 2G - 0x8000_0000 0x8fff_ffff PCI MEM prefetch 256M - 0x9000_0000 0x9fff_ffff PCI MEM non-prefetch 256M - 0xc000_0000 0xdfff_ffff Empty 512M - 0xe000_0000 0xe00f_ffff Int Mem Reg Space 1M - 0xe010_0000 0xe02f_ffff Empty 2M - 0xe030_0000 0xe03f_ffff PCI IO 1M - 0xe040_0000 0xe05f_ffff Empty 2M - 0xe060_0000 0xe060_7fff NAND Flash 32K - 0xf400_0000 0xf7ff_ffff Empty 64M - 0xf800_0000 0xf800_7fff BCSR on CS1 32K - 0xfe00_0000 0xffff_ffff NOR Flash on CS0 32M - -3. Definitions - -3.1 Explanation of NEW definitions in: - - include/configs/MPC837XEMDS.h - - CONFIG_MPC83xx MPC83xx family for both MPC837x and MPC8360 - CONFIG_MPC837x MPC837x specific - CONFIG_MPC837XEMDS MPC837XEMDS board specific - -4. Compilation - - Assuming you're using BASH shell: - - export CROSS_COMPILE=your-cross-compile-prefix - cd u-boot - make distclean - make MPC837XEMDS_config - make - -5. Downloading and Flashing Images - -5.0 Download over serial line using Kermit: - - loadb - [Drop to kermit: - ^\c - send <u-boot-bin-image> - c - ] - - - Or via tftp: - - tftp 40000 u-boot.bin - -5.1 Reflash U-boot Image using U-boot - - tftp 40000 u-boot.bin - protect off fe000000 fe1fffff - erase fe000000 fe1fffff - - cp.b 40000 fe000000 xxxx - -You have to supply the correct byte count with 'xxxx' from the TFTP result log. - -6. Notes - 1) The console baudrate for MPC837XEMDS is 115200bps. |
