summaryrefslogtreecommitdiffstats
path: root/cpu/mpc83xx/spd_sdram.c
diff options
context:
space:
mode:
Diffstat (limited to 'cpu/mpc83xx/spd_sdram.c')
-rw-r--r--cpu/mpc83xx/spd_sdram.c555
1 files changed, 322 insertions, 233 deletions
diff --git a/cpu/mpc83xx/spd_sdram.c b/cpu/mpc83xx/spd_sdram.c
index 48624feca6..0d93f2e1ea 100644
--- a/cpu/mpc83xx/spd_sdram.c
+++ b/cpu/mpc83xx/spd_sdram.c
@@ -1,8 +1,10 @@
/*
+ * (C) Copyright 2006 Freescale Semiconductor, Inc.
+ *
* (C) Copyright 2006
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
- * Copyright 2004 Freescale Semiconductor.
+ * Copyright (C) 2004-2006 Freescale Semiconductor, Inc.
* (C) Copyright 2003 Motorola Inc.
* Xianghua Xiao (X.Xiao@motorola.com)
*
@@ -23,11 +25,6 @@
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
- *
- * Change log:
- *
- * 20050101: Eran Liberty (liberty@freescale.com)
- * Initial file creating (porting from 85XX & 8260)
*/
#include <common.h>
@@ -39,7 +36,9 @@
#ifdef CONFIG_SPD_EEPROM
-#if defined(CONFIG_DDR_ECC)
+DECLARE_GLOBAL_DATA_PTR;
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
extern void dma_init(void);
extern uint dma_check(void);
extern int dma_xfer(void *dest, uint count, void *src);
@@ -52,16 +51,16 @@ extern int dma_xfer(void *dest, uint count, void *src);
/*
* Convert picoseconds into clock cycles (rounding up if needed).
*/
-
int
picos_to_clk(int picos)
{
+ unsigned int ddr_bus_clk;
int clks;
- clks = picos / (2000000000 / (get_bus_freq(0) / 1000));
- if (picos % (2000000000 / (get_bus_freq(0) / 1000)) != 0) {
- clks++;
- }
+ ddr_bus_clk = gd->ddr_clk >> 1;
+ clks = picos / ((1000000000 / ddr_bus_clk) * 1000);
+ if (picos % ((1000000000 / ddr_bus_clk) * 1000) != 0)
+ clks++;
return clks;
}
@@ -103,33 +102,72 @@ static void spd_debug(spd_eeprom_t *spd)
long int spd_sdram()
{
- volatile immap_t *immap = (immap_t *)CFG_IMMRBAR;
- volatile ddr8349_t *ddr = &immap->ddr;
- volatile law8349_t *ecm = &immap->sysconf.ddrlaw[0];
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ volatile ddr83xx_t *ddr = &immap->ddr;
+ volatile law83xx_t *ecm = &immap->sysconf.ddrlaw[0];
spd_eeprom_t spd;
- unsigned tmp, tmp1;
unsigned int memsize;
unsigned int law_size;
- unsigned char caslat;
- unsigned int trfc, trfc_clk, trfc_low;
-
+ unsigned char caslat, caslat_ctrl;
+ unsigned char burstlen;
+ unsigned int max_bus_clk;
+ unsigned int max_data_rate, effective_data_rate;
+ unsigned int ddrc_clk;
+ unsigned int refresh_clk;
+ unsigned sdram_cfg;
+ unsigned int ddrc_ecc_enable;
+
+ /* Read SPD parameters with I2C */
CFG_READ_SPD(SPD_EEPROM_ADDRESS, 0, 1, (uchar *) & spd, sizeof (spd));
#ifdef SPD_DEBUG
spd_debug(&spd);
#endif
+ /* Check the memory type */
+ if (spd.mem_type != SPD_MEMTYPE_DDR) {
+ printf("DDR: Module mem type is %02X\n", spd.mem_type);
+ return 0;
+ }
+
+ /* Check the number of physical bank */
if (spd.nrows > 2) {
- puts("DDR:Only two chip selects are supported on ADS.\n");
+ printf("DDR: The number of physical bank is %02X\n", spd.nrows);
+ return 0;
+ }
+
+ /* Check if the number of row of the module is in the range of DDRC */
+ if (spd.nrow_addr < 12 || spd.nrow_addr > 14) {
+ printf("DDR: Row number is out of range of DDRC, row=%02X\n",
+ spd.nrow_addr);
return 0;
}
- if (spd.nrow_addr < 12
- || spd.nrow_addr > 14
- || spd.ncol_addr < 8
- || spd.ncol_addr > 11) {
- puts("DDR:Row or Col number unsupported.\n");
+ /* Check if the number of col of the module is in the range of DDRC */
+ if (spd.ncol_addr < 8 || spd.ncol_addr > 11) {
+ printf("DDR: Col number is out of range of DDRC, col=%02X\n",
+ spd.ncol_addr);
return 0;
}
+ /* Setup DDR chip select register */
+#ifdef CFG_83XX_DDR_USES_CS0
+ ddr->csbnds[0].csbnds = (banksize(spd.row_dens) >> 24) - 1;
+ ddr->cs_config[0] = ( 1 << 31
+ | (spd.nrow_addr - 12) << 8
+ | (spd.ncol_addr - 8) );
+ debug("\n");
+ debug("cs0_bnds = 0x%08x\n",ddr->csbnds[0].csbnds);
+ debug("cs0_config = 0x%08x\n",ddr->cs_config[0]);
+ if (spd.nrows == 2) {
+ ddr->csbnds[1].csbnds = ( (banksize(spd.row_dens) >> 8)
+ | ((banksize(spd.row_dens) >> 23) - 1) );
+ ddr->cs_config[1] = ( 1<<31
+ | (spd.nrow_addr-12) << 8
+ | (spd.ncol_addr-8) );
+ debug("cs1_bnds = 0x%08x\n",ddr->csbnds[1].csbnds);
+ debug("cs1_config = 0x%08x\n",ddr->cs_config[1]);
+ }
+
+#else
ddr->csbnds[2].csbnds = (banksize(spd.row_dens) >> 24) - 1;
ddr->cs_config[2] = ( 1 << 31
| (spd.nrow_addr - 12) << 8
@@ -147,6 +185,7 @@ long int spd_sdram()
debug("cs3_bnds = 0x%08x\n",ddr->csbnds[3].csbnds);
debug("cs3_config = 0x%08x\n",ddr->cs_config[3]);
}
+#endif
if (spd.mem_type != 0x07) {
puts("No DDR module found!\n");
@@ -172,55 +211,135 @@ long int spd_sdram()
debug("DDR:ar=0x%08x\n", ecm->ar);
/*
- * find the largest CAS
+ * Find the largest CAS by locating the highest 1 bit
+ * in the spd.cas_lat field. Translate it to a DDR
+ * controller field value:
+ *
+ * CAS Lat DDR I Ctrl
+ * Clocks SPD Bit Value
+ * -------+--------+---------
+ * 1.0 0 001
+ * 1.5 1 010
+ * 2.0 2 011
+ * 2.5 3 100
+ * 3.0 4 101
+ * 3.5 5 110
+ * 4.0 6 111
*/
- if(spd.cas_lat & 0x40) {
- caslat = 7;
- } else if (spd.cas_lat & 0x20) {
- caslat = 6;
- } else if (spd.cas_lat & 0x10) {
- caslat = 5;
- } else if (spd.cas_lat & 0x08) {
- caslat = 4;
- } else if (spd.cas_lat & 0x04) {
- caslat = 3;
- } else if (spd.cas_lat & 0x02) {
- caslat = 2;
- } else if (spd.cas_lat & 0x01) {
- caslat = 1;
- } else {
- puts("DDR:no valid CAS Latency information.\n");
- return 0;
- }
+ caslat = __ilog2(spd.cas_lat);
- tmp = 20000 / (((spd.clk_cycle & 0xF0) >> 4) * 10
- + (spd.clk_cycle & 0x0f));
- debug("DDR:Module maximum data rate is: %dMhz\n", tmp);
-
- tmp1 = get_bus_freq(0) / 1000000;
- if (tmp1 < 230 && tmp1 >= 90 && tmp >= 230) {
- /* 90~230 range, treated as DDR 200 */
- if (spd.clk_cycle3 == 0xa0)
- caslat -= 2;
- else if(spd.clk_cycle2 == 0xa0)
- caslat--;
- } else if (tmp1 < 280 && tmp1 >= 230 && tmp >= 280) {
- /* 230-280 range, treated as DDR 266 */
- if (spd.clk_cycle3 == 0x75)
- caslat -= 2;
- else if (spd.clk_cycle2 == 0x75)
- caslat--;
- } else if (tmp1 < 350 && tmp1 >= 280 && tmp >= 350) {
- /* 280~350 range, treated as DDR 333 */
- if (spd.clk_cycle3 == 0x60)
- caslat -= 2;
- else if (spd.clk_cycle2 == 0x60)
- caslat--;
- } else if (tmp1 < 90 || tmp1 >= 350) {
- /* DDR rate out-of-range */
- puts("DDR:platform frequency is not fit for DDR rate\n");
+ if (caslat > 6 ) {
+ printf("DDR: Invalid SPD CAS Latency, caslat=%02X\n",
+ spd.cas_lat);
return 0;
}
+ max_bus_clk = 1000 *10 / (((spd.clk_cycle & 0xF0) >> 4) * 10
+ + (spd.clk_cycle & 0x0f));
+ max_data_rate = max_bus_clk * 2;
+
+ debug("DDR:Module maximum data rate is: %dMhz\n", max_data_rate);
+
+ ddrc_clk = gd->ddr_clk / 1000000;
+
+ if (max_data_rate >= 390) { /* it is DDR 400 */
+ if (ddrc_clk <= 410 && ddrc_clk > 350) {
+ /* DDR controller clk at 350~410 */
+ effective_data_rate = 400; /* 5ns */
+ caslat = caslat;
+ } else if (ddrc_clk <= 350 && ddrc_clk > 280) {
+ /* DDR controller clk at 280~350 */
+ effective_data_rate = 333; /* 6ns */
+ if (spd.clk_cycle2 == 0x60)
+ caslat = caslat - 1;
+ else
+ caslat = caslat;
+ } else if (ddrc_clk <= 280 && ddrc_clk > 230) {
+ /* DDR controller clk at 230~280 */
+ effective_data_rate = 266; /* 7.5ns */
+ if (spd.clk_cycle3 == 0x75)
+ caslat = caslat - 2;
+ else if (spd.clk_cycle2 == 0x60)
+ caslat = caslat - 1;
+ else
+ caslat = caslat;
+ } else if (ddrc_clk <= 230 && ddrc_clk > 90) {
+ /* DDR controller clk at 90~230 */
+ effective_data_rate = 200; /* 10ns */
+ if (spd.clk_cycle3 == 0x75)
+ caslat = caslat - 2;
+ else if (spd.clk_cycle2 == 0x60)
+ caslat = caslat - 1;
+ else
+ caslat = caslat;
+ }
+ } else if (max_data_rate >= 323) { /* it is DDR 333 */
+ if (ddrc_clk <= 350 && ddrc_clk > 280) {
+ /* DDR controller clk at 280~350 */
+ effective_data_rate = 333; /* 6ns */
+ caslat = caslat;
+ } else if (ddrc_clk <= 280 && ddrc_clk > 230) {
+ /* DDR controller clk at 230~280 */
+ effective_data_rate = 266; /* 7.5ns */
+ if (spd.clk_cycle2 == 0x75)
+ caslat = caslat - 1;
+ else
+ caslat = caslat;
+ } else if (ddrc_clk <= 230 && ddrc_clk > 90) {
+ /* DDR controller clk at 90~230 */
+ effective_data_rate = 200; /* 10ns */
+ if (spd.clk_cycle3 == 0xa0)
+ caslat = caslat - 2;
+ else if (spd.clk_cycle2 == 0x75)
+ caslat = caslat - 1;
+ else
+ caslat = caslat;
+ }
+ } else if (max_data_rate >= 256) { /* it is DDR 266 */
+ if (ddrc_clk <= 350 && ddrc_clk > 280) {
+ /* DDR controller clk at 280~350 */
+ printf("DDR: DDR controller freq is more than "
+ "max data rate of the module\n");
+ return 0;
+ } else if (ddrc_clk <= 280 && ddrc_clk > 230) {
+ /* DDR controller clk at 230~280 */
+ effective_data_rate = 266; /* 7.5ns */
+ caslat = caslat;
+ } else if (ddrc_clk <= 230 && ddrc_clk > 90) {
+ /* DDR controller clk at 90~230 */
+ effective_data_rate = 200; /* 10ns */
+ if (spd.clk_cycle2 == 0xa0)
+ caslat = caslat - 1;
+ }
+ } else if (max_data_rate >= 190) { /* it is DDR 200 */
+ if (ddrc_clk <= 350 && ddrc_clk > 230) {
+ /* DDR controller clk at 230~350 */
+ printf("DDR: DDR controller freq is more than "
+ "max data rate of the module\n");
+ return 0;
+ } else if (ddrc_clk <= 230 && ddrc_clk > 90) {
+ /* DDR controller clk at 90~230 */
+ effective_data_rate = 200; /* 10ns */
+ caslat = caslat;
+ }
+ }
+
+ debug("DDR:Effective data rate is: %dMhz\n", effective_data_rate);
+ debug("DDR:The MSB 1 of CAS Latency is: %d\n", caslat);
+
+ /*
+ * Errata DDR6 work around: input enable 2 cycles earlier.
+ * including MPC834x Rev1.0/1.1 and MPC8360 Rev1.1/1.2.
+ */
+ if (caslat == 2)
+ ddr->debug_reg = 0x201c0000; /* CL=2 */
+ else if (caslat == 3)
+ ddr->debug_reg = 0x202c0000; /* CL=2.5 */
+ else if (caslat == 4)
+ ddr->debug_reg = 0x202c0000; /* CL=3.0 */
+
+ __asm__ __volatile__ ("sync");
+
+ debug("Errata DDR6 (debug_reg=0x%08x)\n", ddr->debug_reg);
/*
* note: caslat must also be programmed into ddr->sdram_mode
@@ -229,16 +348,14 @@ long int spd_sdram()
* note: WRREC(Twr) and WRTORD(Twtr) are not in SPD,
* use conservative value here.
*/
- trfc = spd.trfc * 1000; /* up to ps */
- trfc_clk = picos_to_clk(trfc);
- trfc_low = (trfc_clk - 8) & 0xf;
+ caslat_ctrl = (caslat + 1) & 0x07; /* see as above */
ddr->timing_cfg_1 =
(((picos_to_clk(spd.trp * 250) & 0x07) << 28 ) |
((picos_to_clk(spd.tras * 1000) & 0x0f ) << 24 ) |
((picos_to_clk(spd.trcd * 250) & 0x07) << 20 ) |
- ((caslat & 0x07) << 16 ) |
- (trfc_low << 12 ) |
+ ((caslat_ctrl & 0x07) << 16 ) |
+ (((picos_to_clk(spd.trfc * 1000) - 8) & 0x0f) << 12 ) |
( 0x300 ) |
((picos_to_clk(spd.trrd * 250) & 0x07) << 4) | 1);
@@ -246,144 +363,143 @@ long int spd_sdram()
debug("DDR:timing_cfg_1=0x%08x\n", ddr->timing_cfg_1);
debug("DDR:timing_cfg_2=0x%08x\n", ddr->timing_cfg_2);
+ /* Setup init value, but not enable */
+ ddr->sdram_cfg = 0x42000000;
- /*
- * Only DDR I is supported
- * DDR I and II have different mode-register-set definition
+ /* Check DIMM data bus width */
+ if (spd.dataw_lsb == 0x20) {
+ burstlen = 0x03; /* 32 bit data bus, burst len is 8 */
+ printf("\n DDR DIMM: data bus width is 32 bit");
+ } else {
+ burstlen = 0x02; /* Others act as 64 bit bus, burst len is 4 */
+ printf("\n DDR DIMM: data bus width is 64 bit");
+ }
+
+ /* Is this an ECC DDR chip? */
+ if (spd.config == 0x02)
+ printf(" with ECC\n");
+ else
+ printf(" without ECC\n");
+
+ /* Burst length is always 4 for 64 bit data bus, 8 for 32 bit data bus,
+ Burst type is sequential
*/
- switch(caslat) {
- case 2:
- tmp = 0x50; /* 1.5 */
- break;
- case 3:
- tmp = 0x20; /* 2.0 */
- break;
- case 4:
- tmp = 0x60; /* 2.5 */
- break;
- case 5:
- tmp = 0x30; /* 3.0 */
- break;
- default:
- puts("DDR:only CAS Latency 1.5, 2.0, 2.5, 3.0 is supported.\n");
- return 0;
+ switch (caslat) {
+ case 1:
+ ddr->sdram_mode = 0x50 | burstlen; /* CL=1.5 */
+ break;
+ case 2:
+ ddr->sdram_mode = 0x20 | burstlen; /* CL=2.0 */
+ break;
+ case 3:
+ ddr->sdram_mode = 0x60 | burstlen; /* CL=2.5 */
+ break;
+ case 4:
+ ddr->sdram_mode = 0x30 | burstlen; /* CL=3.0 */
+ break;
+ default:
+ printf("DDR:only CL 1.5, 2.0, 2.5, 3.0 is supported\n");
+ return 0;
}
-#if defined (CONFIG_DDR_32BIT)
- /* set burst length to 8 for 32-bit data path */
- tmp |= 0x03;
-#else
- /* set burst length to 4 - default for 64-bit data path */
- tmp |= 0x02;
-#endif
- ddr->sdram_mode = tmp;
debug("DDR:sdram_mode=0x%08x\n", ddr->sdram_mode);
- switch(spd.refresh) {
- case 0x00:
- case 0x80:
- tmp = picos_to_clk(15625000);
- break;
- case 0x01:
- case 0x81:
- tmp = picos_to_clk(3900000);
- break;
- case 0x02:
- case 0x82:
- tmp = picos_to_clk(7800000);
- break;
- case 0x03:
- case 0x83:
- tmp = picos_to_clk(31300000);
- break;
- case 0x04:
- case 0x84:
- tmp = picos_to_clk(62500000);
- break;
- case 0x05:
- case 0x85:
- tmp = picos_to_clk(125000000);
- break;
- default:
- tmp = 0x512;
- break;
+ switch (spd.refresh) {
+ case 0x00:
+ case 0x80:
+ refresh_clk = picos_to_clk(15625000);
+ break;
+ case 0x01:
+ case 0x81:
+ refresh_clk = picos_to_clk(3900000);
+ break;
+ case 0x02:
+ case 0x82:
+ refresh_clk = picos_to_clk(7800000);
+ break;
+ case 0x03:
+ case 0x83:
+ refresh_clk = picos_to_clk(31300000);
+ break;
+ case 0x04:
+ case 0x84:
+ refresh_clk = picos_to_clk(62500000);
+ break;
+ case 0x05:
+ case 0x85:
+ refresh_clk = picos_to_clk(125000000);
+ break;
+ default:
+ refresh_clk = 0x512;
+ break;
}
/*
* Set BSTOPRE to 0x100 for page mode
* If auto-charge is used, set BSTOPRE = 0
*/
- ddr->sdram_interval = ((tmp & 0x3fff) << 16) | 0x100;
+ ddr->sdram_interval = ((refresh_clk & 0x3fff) << 16) | 0x100;
debug("DDR:sdram_interval=0x%08x\n", ddr->sdram_interval);
- /*
- * Is this an ECC DDR chip?
+ /* SS_EN = 0, source synchronous disable
+ * CLK_ADJST = 0, MCK/MCK# is launched aligned with addr/cmd
*/
-#if defined(CONFIG_DDR_ECC)
- if (spd.config == 0x02) {
- /* disable error detection */
- ddr->err_disable = ~ECC_ERROR_ENABLE;
+ ddr->sdram_clk_cntl = 0x00000000;
+ debug("DDR:sdram_clk_cntl=0x%08x\n", ddr->sdram_clk_cntl);
- /* set single bit error threshold to maximum value,
- * reset counter to zero */
- ddr->err_sbe = (255 << ECC_ERROR_MAN_SBET_SHIFT) |
- (0 << ECC_ERROR_MAN_SBEC_SHIFT);
- }
- debug("DDR:err_disable=0x%08x\n", ddr->err_disable);
- debug("DDR:err_sbe=0x%08x\n", ddr->err_sbe);
-#endif
asm("sync;isync");
- udelay(500);
+ udelay(600);
/*
- * SS_EN=1,
- * CLK_ADJST = 2-MCK/MCK_B, is lauched 1/2 of one SDRAM
- * clock cycle after address/command
- */
- /*ddr->sdram_clk_cntl = 0x82000000;*/
- ddr->sdram_clk_cntl = (DDR_SDRAM_CLK_CNTL_SS_EN|DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05);
-
- /*
- * Figure out the settings for the sdram_cfg register. Build up
- * the entire register in 'tmp' before writing since the write into
+ * Figure out the settings for the sdram_cfg register. Build up
+ * the value in 'sdram_cfg' before writing since the write into
* the register will actually enable the memory controller, and all
* settings must be done before enabling.
*
* sdram_cfg[0] = 1 (ddr sdram logic enable)
* sdram_cfg[1] = 1 (self-refresh-enable)
* sdram_cfg[6:7] = 2 (SDRAM type = DDR SDRAM)
+ * sdram_cfg[12] = 0 (32_BE =0 , 64 bit bus mode)
+ * sdram_cfg[13] = 0 (8_BE =0, 4-beat bursts)
*/
- tmp = 0xc2000000;
+ sdram_cfg = 0xC2000000;
-#if defined (CONFIG_DDR_32BIT)
- /* in 32-Bit mode burst len is 8 beats */
- tmp |= (SDRAM_CFG_32_BE | SDRAM_CFG_8_BE);
-#endif
- /*
- * sdram_cfg[3] = RD_EN - registered DIMM enable
- * A value of 0x26 indicates micron registered DIMMS (micron.com)
- */
- if (spd.mod_attr == 0x26) {
- tmp |= 0x10000000;
- }
+ /* sdram_cfg[3] = RD_EN - registered DIMM enable */
+ if (spd.mod_attr & 0x02)
+ sdram_cfg |= 0x10000000;
+
+ /* The DIMM is 32bit width */
+ if (spd.dataw_lsb == 0x20)
+ sdram_cfg |= 0x000C0000;
+
+ ddrc_ecc_enable = 0;
#if defined(CONFIG_DDR_ECC)
- /*
- * If the user wanted ECC (enabled via sdram_cfg[2])
- */
+ /* Enable ECC with sdram_cfg[2] */
if (spd.config == 0x02) {
- tmp |= SDRAM_CFG_ECC_EN;
+ sdram_cfg |= 0x20000000;
+ ddrc_ecc_enable = 1;
+ /* disable error detection */
+ ddr->err_disable = ~ECC_ERROR_ENABLE;
+ /* set single bit error threshold to maximum value,
+ * reset counter to zero */
+ ddr->err_sbe = (255 << ECC_ERROR_MAN_SBET_SHIFT) |
+ (0 << ECC_ERROR_MAN_SBEC_SHIFT);
}
+
+ debug("DDR:err_disable=0x%08x\n", ddr->err_disable);
+ debug("DDR:err_sbe=0x%08x\n", ddr->err_sbe);
#endif
+ printf(" DDRC ECC mode: %s\n", ddrc_ecc_enable ? "ON":"OFF");
#if defined(CONFIG_DDR_2T_TIMING)
/*
* Enable 2T timing by setting sdram_cfg[16].
*/
- tmp |= SDRAM_CFG_2T_EN;
+ sdram_cfg |= SDRAM_CFG_2T_EN;
#endif
-
- ddr->sdram_cfg = tmp;
+ /* Enable controller, and GO! */
+ ddr->sdram_cfg = sdram_cfg;
asm("sync;isync");
udelay(500);
@@ -392,8 +508,7 @@ long int spd_sdram()
}
#endif /* CONFIG_SPD_EEPROM */
-
-#if defined(CONFIG_DDR_ECC)
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
/*
* Use timebase counter, get_timer() is not availabe
* at this point of initialization yet.
@@ -429,74 +544,48 @@ static __inline__ unsigned long get_tbms (void)
/* #define CONFIG_DDR_ECC_INIT_VIA_DMA */
void ddr_enable_ecc(unsigned int dram_size)
{
- uint *p;
- volatile immap_t *immap = (immap_t *)CFG_IMMRBAR;
- volatile ddr8349_t *ddr = &immap->ddr;
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ volatile ddr83xx_t *ddr= &immap->ddr;
unsigned long t_start, t_end;
+ register u64 *p;
+ register uint size;
+ unsigned int pattern[2];
#if defined(CONFIG_DDR_ECC_INIT_VIA_DMA)
uint i;
#endif
-
- debug("Initialize a Cachline in DRAM\n");
icache_enable();
-
-#if defined(CONFIG_DDR_ECC_INIT_VIA_DMA)
- /* Initialise DMA for direct Transfers */
- dma_init();
-#endif
-
t_start = get_tbms();
+ pattern[0] = 0xdeadbeef;
+ pattern[1] = 0xdeadbeef;
#if !defined(CONFIG_DDR_ECC_INIT_VIA_DMA)
- debug("DDR init: Cache flush method\n");
- for (p = 0; p < (uint *)(dram_size); p++) {
- if (((unsigned int)p & 0x1f) == 0) {
- ppcDcbz((unsigned long) p);
- }
-
- /* write pattern to cache and flush */
- *p = (unsigned int)0xdeadbeef;
-
- if (((unsigned int)p & 0x1c) == 0x1c) {
- ppcDcbf((unsigned long) p);
- }
+ debug("ddr init: CPU FP write method\n");
+ size = dram_size;
+ for (p = 0; p < (u64*)(size); p++) {
+ ppcDWstore((u32*)p, pattern);
}
+ __asm__ __volatile__ ("sync");
#else
- printf("DDR init: DMA method\n");
- for (p = 0; p < (uint *)(8 * 1024); p++) {
- /* zero one data cache line */
- if (((unsigned int)p & 0x1f) == 0) {
- ppcDcbz((unsigned long)p);
- }
-
- /* write pattern to it and flush */
- *p = (unsigned int)0xdeadbeef;
-
- if (((unsigned int)p & 0x1c) == 0x1c) {
- ppcDcbf((unsigned long)p);
- }
+ debug("ddr init: DMA method\n");
+ size = 0x2000;
+ for (p = 0; p < (u64*)(size); p++) {
+ ppcDWstore((u32*)p, pattern);
}
+ __asm__ __volatile__ ("sync");
- /* 8K */
- dma_xfer((uint *)0x2000, 0x2000, (uint *)0);
- /* 16K */
- dma_xfer((uint *)0x4000, 0x4000, (uint *)0);
- /* 32K */
- dma_xfer((uint *)0x8000, 0x8000, (uint *)0);
- /* 64K */
- dma_xfer((uint *)0x10000, 0x10000, (uint *)0);
- /* 128k */
- dma_xfer((uint *)0x20000, 0x20000, (uint *)0);
- /* 256k */
- dma_xfer((uint *)0x40000, 0x40000, (uint *)0);
- /* 512k */
- dma_xfer((uint *)0x80000, 0x80000, (uint *)0);
- /* 1M */
- dma_xfer((uint *)0x100000, 0x100000, (uint *)0);
- /* 2M */
- dma_xfer((uint *)0x200000, 0x200000, (uint *)0);
- /* 4M */
- dma_xfer((uint *)0x400000, 0x400000, (uint *)0);
+ /* Initialise DMA for direct transfer */
+ dma_init();
+ /* Start DMA to transfer */
+ dma_xfer((uint *)0x2000, 0x2000, (uint *)0); /* 8K */
+ dma_xfer((uint *)0x4000, 0x4000, (uint *)0); /* 16K */
+ dma_xfer((uint *)0x8000, 0x8000, (uint *)0); /* 32K */
+ dma_xfer((uint *)0x10000, 0x10000, (uint *)0); /* 64K */
+ dma_xfer((uint *)0x20000, 0x20000, (uint *)0); /* 128K */
+ dma_xfer((uint *)0x40000, 0x40000, (uint *)0); /* 256K */
+ dma_xfer((uint *)0x80000, 0x80000, (uint *)0); /* 512K */
+ dma_xfer((uint *)0x100000, 0x100000, (uint *)0); /* 1M */
+ dma_xfer((uint *)0x200000, 0x200000, (uint *)0); /* 2M */
+ dma_xfer((uint *)0x400000, 0x400000, (uint *)0); /* 4M */
for (i = 1; i < dram_size / 0x800000; i++) {
dma_xfer((uint *)(0x800000*i), 0x800000, (uint *)0);
OpenPOWER on IntegriCloud