diff options
Diffstat (limited to 'board/samsung')
| -rw-r--r-- | board/samsung/smdk5250/exynos5-dt.c | 100 |
1 files changed, 99 insertions, 1 deletions
diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c index bce7583fd0..d6ce1337b9 100644 --- a/board/samsung/smdk5250/exynos5-dt.c +++ b/board/samsung/smdk5250/exynos5-dt.c @@ -11,9 +11,9 @@ #include <i2c.h> #include <netdev.h> #include <spi.h> +#include <asm/gpio.h> #include <asm/arch/cpu.h> #include <asm/arch/dwmmc.h> -#include <asm/arch/gpio.h> #include <asm/arch/mmc.h> #include <asm/arch/pinmux.h> #include <asm/arch/power.h> @@ -180,6 +180,59 @@ int exynos_power_init(void) #endif /* CONFIG_POWER */ #ifdef CONFIG_LCD +static int board_dp_bridge_setup(void) +{ + const int max_tries = 10; + int num_tries, node; + + /* + * TODO(sjg): Use device tree for GPIOs when exynos GPIO + * numbering patch is in mainline. + */ + debug("%s\n", __func__); + node = fdtdec_next_compatible(gd->fdt_blob, 0, COMPAT_NXP_PTN3460); + if (node < 0) { + debug("%s: No node for DP bridge in device tree\n", __func__); + return -ENODEV; + } + + /* Setup the GPIOs */ + + /* PD is ACTIVE_LOW, and initially de-asserted */ + gpio_set_pull(EXYNOS5_GPIO_Y25, S5P_GPIO_PULL_NONE); + gpio_direction_output(EXYNOS5_GPIO_Y25, 1); + + /* Reset is ACTIVE_LOW */ + gpio_set_pull(EXYNOS5_GPIO_X15, S5P_GPIO_PULL_NONE); + gpio_direction_output(EXYNOS5_GPIO_X15, 0); + + udelay(10); + gpio_set_value(EXYNOS5_GPIO_X15, 1); + + gpio_direction_input(EXYNOS5_GPIO_X07); + + /* + * We need to wait for 90ms after bringing up the bridge since there + * is a phantom "high" on the HPD chip during its bootup. The phantom + * high comes within 7ms of de-asserting PD and persists for at least + * 15ms. The real high comes roughly 50ms after PD is de-asserted. The + * phantom high makes it hard for us to know when the NXP chip is up. + */ + mdelay(90); + + for (num_tries = 0; num_tries < max_tries; num_tries++) { + /* Check HPD. If it's high, we're all good. */ + if (gpio_get_value(EXYNOS5_GPIO_X07)) + return 0; + + debug("%s: eDP bridge failed to come up; try %d of %d\n", + __func__, num_tries, max_tries); + } + + /* Immediately go into bridge reset if the hp line is not high */ + return -ENODEV; +} + void exynos_cfg_lcd_gpio(void) { /* For Backlight */ @@ -198,4 +251,49 @@ void exynos_set_dp_phy(unsigned int onoff) { set_dp_phy_ctrl(onoff); } + +void exynos_backlight_on(unsigned int on) +{ + debug("%s(%u)\n", __func__, on); + + if (!on) + return; + +#ifdef CONFIG_POWER_TPS65090 + int ret; + + ret = tps65090_fet_enable(1); /* Enable FET1, backlight */ + if (ret) + return; + + /* T5 in the LCD timing spec (defined as > 10ms) */ + mdelay(10); + + /* board_dp_backlight_pwm */ + gpio_direction_output(EXYNOS5_GPIO_B20, 1); + + /* T6 in the LCD timing spec (defined as > 10ms) */ + mdelay(10); + + /* board_dp_backlight_en */ + gpio_direction_output(EXYNOS5_GPIO_X30, 1); +#endif +} + +void exynos_lcd_power_on(void) +{ + int ret; + + debug("%s\n", __func__); + +#ifdef CONFIG_POWER_TPS65090 + /* board_dp_lcd_vdd */ + tps65090_fet_enable(6); /* Enable FET6, lcd panel */ +#endif + + ret = board_dp_bridge_setup(); + if (ret && ret != -ENODEV) + printf("LCD bridge failed to enable: %d\n", ret); +} + #endif |
