diff options
Diffstat (limited to 'board/karo/tk71/kwbimage.cfg')
| -rw-r--r-- | board/karo/tk71/kwbimage.cfg | 158 |
1 files changed, 0 insertions, 158 deletions
diff --git a/board/karo/tk71/kwbimage.cfg b/board/karo/tk71/kwbimage.cfg deleted file mode 100644 index a32e27c6a0..0000000000 --- a/board/karo/tk71/kwbimage.cfg +++ /dev/null @@ -1,158 +0,0 @@ -# -# (C) Copyright 2009 -# Marvell Semiconductor <www.marvell.com> -# Written-by: Prafulla Wadaskar <prafulla@marvell.com> -# -# adopted to TK71 by -# Nils Faerber <nils.faerber@kernelconcepts.de> -# -# SPDX-License-Identifier: GPL-2.0+ -# -# Refer doc/README.kwbimage for more details about how-to configure -# and create kirkwood boot image -# - -# Boot Media configurations -BOOT_FROM nand -NAND_ECC_MODE default -NAND_PAGE_SIZE 0x0800 - -# SOC registers configuration using bootrom header extension -# Maximum KWBIMAGE_MAX_CONFIG configurations allowed - -# Configure RGMII-0 interface pad voltage to 1.8V -DATA 0xFFD100e0 0x1b1b1b9b - -#Dram initalization for SINGLE x16 CL=5 @ 400MHz -DATA 0xFFD01400 0x43000c30 # DDR Configuration register -# bit13-0: 0xc30 (3120 DDR2 clks refresh rate) -# bit23-14: zero -# bit24: 1= enable exit self refresh mode on DDR access -# bit25: 1 required -# bit29-26: zero -# bit31-30: 01 - -DATA 0xFFD01404 0x36543000 # DDR Controller Control Low -# bit 4: 0=addr/cmd in smame cycle -# bit 5: 0=clk is driven during self refresh, we don't care for APX -# bit 6: 0=use recommended falling edge of clk for addr/cmd -# bit14: 0=input buffer always powered up -# bit18: 1=cpu lock transaction enabled -# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 -# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM -# bit30-28: 3 required -# bit31: 0=no additional STARTBURST delay - -DATA 0xFFD01408 0x1101355b # DDR Timing (Low) (active cycles value +1) -# bit3-0: TRAS lsbs -# bit7-4: TRCD -# bit11- 8: TRP -# bit15-12: TWR -# bit19-16: TWTR -# bit20: TRAS msb -# bit23-21: 0x0 -# bit27-24: TRRD -# bit31-28: TRTP - -DATA 0xFFD0140C 0x00000034 # DDR Timing (High) -# bit6-0: TRFC -# bit8-7: TR2R -# bit10-9: TR2W -# bit12-11: TW2W -# bit31-13: zero required - -DATA 0xFFD01410 0x00000000 # DDR Address Control -# bit1-0: 01, Cs0width=x16 -# bit3-2: 10, Cs0size=512Mb -# bit5-4: 01, Cs1width=x16 -# bit7-6: 10, Cs1size=512Mb -# bit9-8: 00, Cs2width=nonexistent -# bit11-10: 00, Cs2size =nonexistent -# bit13-12: 00, Cs3width=nonexistent -# bit15-14: 00, Cs3size =nonexistent -# bit16: 0, Cs0AddrSel -# bit17: 0, Cs1AddrSel -# bit18: 0, Cs2AddrSel -# bit19: 0, Cs3AddrSel -# bit31-20: 0 required - -DATA 0xFFD01414 0x00000000 # DDR Open Pages Control -# bit0: 0, OpenPage enabled -# bit31-1: 0 required - -DATA 0xFFD01418 0x00000000 # DDR Operation -# bit3-0: 0x0, DDR cmd -# bit31-4: 0 required - -DATA 0xFFD0141C 0x00000652 # DDR Mode -# bit2-0: 2, BurstLen=2 required -# bit3: 0, BurstType=0 required -# bit6-4: 4, CL=5 -# bit7: 0, TestMode=0 normal -# bit8: 0, DLL reset=0 normal -# bit11-9: 6, auto-precharge write recovery ???????????? -# bit12: 0, PD must be zero -# bit31-13: 0 required - -DATA 0xFFD01420 0x00000042 # DDR Extended Mode -# bit0: 0, DDR DLL enabled -# bit1: 0, DDR drive strenght normal -# bit2: 0, DDR ODT control lsd (disabled) -# bit5-3: 000, required -# bit6: 1, DDR ODT control msb, (disabled) -# bit9-7: 000, required -# bit10: 0, differential DQS enabled -# bit11: 0, required -# bit12: 0, DDR output buffer enabled -# bit31-13: 0 required - -DATA 0xFFD01424 0x0000F17F # DDR Controller Control High -# bit2-0: 111, required -# bit3 : 1 , MBUS Burst Chop disabled -# bit6-4: 111, required -# bit7 : 0 -# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz -# bit9 : 0 , no half clock cycle addition to dataout -# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals -# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh -# bit15-12: 1111 required -# bit31-16: 0 required - -DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) -DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) - -DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 -DATA 0xFFD01504 0x1FFFFFF1 # CS[0]n Size -# bit0: 1, Window enabled -# bit1: 0, Write Protect disabled -# bit3-2: 00, CS0 hit selected -# bit23-4: ones, required -# bit31-24: 0x0F, Size (i.e. 256MB) - -DATA 0xFFD01508 0x00000000 # CS[1]n Base address to 256Mb -DATA 0xFFD0150C 0x00000000 # CS[1]n Size 256Mb Window enabled for CS1 - -DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled -DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled - -DATA 0xFFD01494 0x00110000 # DDR ODT Control (Low) -# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1 -# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0 -# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1. -# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0. -DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) -# bit1-0: 00, ODT0 controlled by ODT Control (low) register above -# bit3-2: 01, ODT1 active NEVER! -# bit31-4: zero, required - -DATA 0xFFD0149C 0x0000F80F # CPU ODT Control -# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3 -# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm -# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm -# bit14: 1, M_STARTBURST_IN ODT: Enabled -# bit15: 1, DDR IO ODT Unit: Use ODT block -DATA 0xFFD01480 0x00000001 # DDR Initialization Control -#bit0=1, enable DDR init upon this register write - -# End of Header extension -DATA 0x0 0x0 |
