diff options
Diffstat (limited to 'board/freescale/mpc8360emds/README')
| -rw-r--r-- | board/freescale/mpc8360emds/README | 155 |
1 files changed, 0 insertions, 155 deletions
diff --git a/board/freescale/mpc8360emds/README b/board/freescale/mpc8360emds/README deleted file mode 100644 index 6afa753969..0000000000 --- a/board/freescale/mpc8360emds/README +++ /dev/null @@ -1,155 +0,0 @@ -Freescale MPC8360EMDS Board ------------------------------------------ -1. Board Switches and Jumpers -1.0 There are four Dual-In-Line Packages(DIP) Switches on MPC8360EMDS board - For some reason, the HW designers describe the switch settings - in terms of 0 and 1, and then map that to physical switches where - the label "On" refers to logic 0 and "Off" is logic 1. - - Switch bits are numbered 1 through, like, 4 6 8 or 10, but the - bits may contribute to signals that are numbered based at 0, - and some of those signals may be high-bit-number-0 too. Heed - well the names and labels and do not get confused. - - "Off" == 1 - "On" == 0 - - SW18 is switch 18 as silk-screened onto the board. - SW4[8] is the bit labeled 8 on Switch 4. - SW2[1:6] refers to bits labeled 1 through 6 in order on switch 2. - SW3[7:1] refers to bits labeled 7 through 1 in order on switch 3. - SW3[1:8]= 0000_0001 refers to bits labeled 1 through 6 is set as "On" - and bits labeled 8 is set as "Off". - -1.1 There are three type boards for MPC8360E silicon up to now, They are - - * MPC8360E-MDS-PB PROTO (a.k.a 8360SYS PROTOTYPE) - * MPC8360E-MDS-PB PILOT (a.k.a 8360SYS PILOT) - * MPC8360EA-MDS-PB PROTO (a.k.a 8360SYS2 PROTOTYPE) - -1.2 For all the MPC8360EMDS Board - - First, make sure the board default setting is consistent with the - document shipped with your board. Then apply the following setting: - SW3[1-8]= 0000_0100 (HRCW setting value is performed on local bus) - SW4[1-8]= 0011_0000 (Flash boot on local bus) - SW9[1-8]= 0110_0110 (PCI Mode enabled. HRCW is read from FLASH) - SW10[1-8]= 0000_1000 (core PLL setting) - SW11[1-8]= 0000_0100 (SW11 is on the another side of the board) - JP6 1-2 - on board Oscillator: 66M - -1.3 Since different board/chip rev. combinations have AC timing issues, - u-boot forces RGMII-ID (RGMII with Internal Delay) mode on by default - by the patch (mpc83xx: Disable G1TXCLK, G2TXCLK h/w buffers). - - When the rev2.x silicon mount on these boards, and if you are using - u-boot version after this patch, to make the ethernet interfaces usable, - and to enable RGMII-ID on your board, you have to setup the jumpers - correctly. - - * MPC8360E-MDS-PB PROTO - nothing to do - * MPC8360E-MDS-PB PILOT - JP9 and JP8 should be ON - * MPC8360EA-MDS-PB PROTO - JP2 and JP3 should be ON - -2. Memory Map - -2.1. The memory map should look pretty much like this: - - 0x0000_0000 0x7fff_ffff DDR 2G - 0x8000_0000 0x8fff_ffff PCI MEM prefetch 256M - 0x9000_0000 0x9fff_ffff PCI MEM non-prefetch 256M - 0xc000_0000 0xdfff_ffff Empty 512M - 0xe000_0000 0xe01f_ffff Int Mem Reg Space 2M - 0xe020_0000 0xe02f_ffff Empty 1M - 0xe030_0000 0xe03f_ffff PCI IO 1M - 0xe040_0000 0xefff_ffff Empty 252M - 0xf000_0000 0xf3ff_ffff Local Bus SDRAM 64M - 0xf400_0000 0xf7ff_ffff Empty 64M - 0xf800_0000 0xf800_7fff BCSR on CS1 32K - 0xf800_8000 0xf800_ffff PIB CS4 32K - 0xf801_0000 0xf801_7fff PIB CS5 32K - 0xfe00_0000 0xfeff_ffff FLASH on CS0 16M - - -3. Definitions - -3.1 Explanation of NEW definitions in: - - include/configs/MPC8360EMDS.h - - CONFIG_MPC83xx MPC83xx family for both MPC8349 and MPC8360 - CONFIG_MPC8360 MPC8360 specific - CONFIG_MPC8360EMDS MPC8360EMDS board specific - -4. Compilation - - MPC8360EMDS shipped with 33.33MHz or 66MHz oscillator(check U41 chip). - - Assuming you're using BASH shell: - - export CROSS_COMPILE=your-cross-compile-prefix - cd u-boot - make distclean - make MPC8360EMDS_XX_config - make - - MPC8360EMDS support ATM, PCI in host and slave mode. - - To make u-boot support ATM : - 1) Make MPC8360EMDS_XX_ATM_config - - To make u-boot support PCI host 66M : - 1) DIP SW support PCI mode as described in Section 1.1. - 2) Make MPC8360EMDS_XX_HOST_66_config - - To make u-boot support PCI host 33M : - 1) DIP SW setting is similar as Section 1.1, except for SW3[4] is 1 - 2) Make MPC8360EMDS_XX_HOST_33_config - - To make u-boot support PCI slave 66M : - 1) DIP SW setting is similar as Section 1.1, except for SW9[3] is 1 - 2) Make MPC8360EMDS_XX_SLAVE_config - - (where XX is: - 33 - 33.33MHz oscillator - 66 - 66MHz oscillator) - -5. Downloading and Flashing Images - -5.0 Download over serial line using Kermit: - - loadb - [Drop to kermit: - ^\c - send <u-boot-bin-image> - c - ] - - - Or via tftp: - - tftp 10000 u-boot.bin - -5.1 Reflash U-boot Image using U-boot - - tftp 20000 u-boot.bin - protect off fef00000 fef3ffff - erase fef00000 fef3ffff - - cp.b 20000 fef00000 xxxx - - or - - cp.b 20000 fef00000 3ffff - - -You have to supply the correct byte count with 'xxxx' from the TFTP result log. -Maybe 3ffff will work too, that corresponds to the erased sectors. - - -6. Notes - 1) The console baudrate for MPC8360EMDS is 115200bps. |
