diff options
Diffstat (limited to 'board/compulab/cm_fx6/cm_fx6.c')
| -rw-r--r-- | board/compulab/cm_fx6/cm_fx6.c | 483 |
1 files changed, 483 insertions, 0 deletions
diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c new file mode 100644 index 0000000000..fdb8ebf9e7 --- /dev/null +++ b/board/compulab/cm_fx6/cm_fx6.c @@ -0,0 +1,483 @@ +/* + * Board functions for Compulab CM-FX6 board + * + * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/ + * + * Author: Nikita Kiryanov <nikita@compulab.co.il> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <fsl_esdhc.h> +#include <miiphy.h> +#include <netdev.h> +#include <fdt_support.h> +#include <sata.h> +#include <asm/arch/crm_regs.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/iomux.h> +#include <asm/imx-common/mxc_i2c.h> +#include <asm/imx-common/sata.h> +#include <asm/io.h> +#include <asm/gpio.h> +#include "common.h" +#include "../common/eeprom.h" + +DECLARE_GLOBAL_DATA_PTR; + +#ifdef CONFIG_DWC_AHSATA +static int cm_fx6_issd_gpios[] = { + /* The order of the GPIOs in the array is important! */ + CM_FX6_SATA_PHY_SLP, + CM_FX6_SATA_NRSTDLY, + CM_FX6_SATA_PWREN, + CM_FX6_SATA_NSTANDBY1, + CM_FX6_SATA_NSTANDBY2, + CM_FX6_SATA_LDO_EN, +}; + +static void cm_fx6_sata_power(int on) +{ + int i; + + if (!on) { /* tell the iSSD that the power will be removed */ + gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 1); + mdelay(10); + } + + for (i = 0; i < ARRAY_SIZE(cm_fx6_issd_gpios); i++) { + gpio_direction_output(cm_fx6_issd_gpios[i], on); + udelay(100); + } + + if (!on) /* for compatibility lower the power loss interrupt */ + gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0); +} + +static iomux_v3_cfg_t const sata_pads[] = { + /* SATA PWR */ + IOMUX_PADS(PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_EIM_A22__GPIO2_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_EIM_D20__GPIO3_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL)), + /* SATA CTRL */ + IOMUX_PADS(PAD_ENET_TXD0__GPIO1_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_EIM_D23__GPIO3_IO23 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_EIM_A23__GPIO6_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL)), +}; + +static void cm_fx6_setup_issd(void) +{ + SETUP_IOMUX_PADS(sata_pads); + /* Make sure this gpio has logical 0 value */ + gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0); + udelay(100); + + cm_fx6_sata_power(0); + mdelay(250); + cm_fx6_sata_power(1); +} + +#define CM_FX6_SATA_INIT_RETRIES 10 +int sata_initialize(void) +{ + int err, i; + + cm_fx6_setup_issd(); + for (i = 0; i < CM_FX6_SATA_INIT_RETRIES; i++) { + err = setup_sata(); + if (err) { + printf("SATA setup failed: %d\n", err); + return err; + } + + udelay(100); + + err = __sata_initialize(); + if (!err) + break; + + /* There is no device on the SATA port */ + if (sata_port_status(0, 0) == 0) + break; + + /* There's a device, but link not established. Retry */ + } + + return err; +} +#endif + +#ifdef CONFIG_SYS_I2C_MXC +#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE | PAD_CTL_SRE_FAST) + +I2C_PADS(i2c0_pads, + PAD_EIM_D21__I2C1_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL), + PAD_EIM_D21__GPIO3_IO21 | MUX_PAD_CTRL(I2C_PAD_CTRL), + IMX_GPIO_NR(3, 21), + PAD_EIM_D28__I2C1_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL), + PAD_EIM_D28__GPIO3_IO28 | MUX_PAD_CTRL(I2C_PAD_CTRL), + IMX_GPIO_NR(3, 28)); + +I2C_PADS(i2c1_pads, + PAD_KEY_COL3__I2C2_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL), + PAD_KEY_COL3__GPIO4_IO12 | MUX_PAD_CTRL(I2C_PAD_CTRL), + IMX_GPIO_NR(4, 12), + PAD_KEY_ROW3__I2C2_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL), + PAD_KEY_ROW3__GPIO4_IO13 | MUX_PAD_CTRL(I2C_PAD_CTRL), + IMX_GPIO_NR(4, 13)); + +I2C_PADS(i2c2_pads, + PAD_GPIO_3__I2C3_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL), + PAD_GPIO_3__GPIO1_IO03 | MUX_PAD_CTRL(I2C_PAD_CTRL), + IMX_GPIO_NR(1, 3), + PAD_GPIO_6__I2C3_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL), + PAD_GPIO_6__GPIO1_IO06 | MUX_PAD_CTRL(I2C_PAD_CTRL), + IMX_GPIO_NR(1, 6)); + + +static void cm_fx6_setup_i2c(void) +{ + setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, I2C_PADS_INFO(i2c0_pads)); + setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, I2C_PADS_INFO(i2c1_pads)); + setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, I2C_PADS_INFO(i2c2_pads)); +} +#else +static void cm_fx6_setup_i2c(void) { } +#endif + +#ifdef CONFIG_USB_EHCI_MX6 +#define WEAK_PULLDOWN (PAD_CTL_PUS_100K_DOWN | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ + PAD_CTL_HYS | PAD_CTL_SRE_SLOW) + +static int cm_fx6_usb_hub_reset(void) +{ + int err; + + err = gpio_request(CM_FX6_USB_HUB_RST, "usb hub rst"); + if (err) { + printf("USB hub rst gpio request failed: %d\n", err); + return -1; + } + + SETUP_IOMUX_PAD(PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL)); + gpio_direction_output(CM_FX6_USB_HUB_RST, 0); + udelay(10); + gpio_direction_output(CM_FX6_USB_HUB_RST, 1); + mdelay(1); + + return 0; +} + +static int cm_fx6_init_usb_otg(void) +{ + int ret; + struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; + + ret = gpio_request(SB_FX6_USB_OTG_PWR, "usb-pwr"); + if (ret) { + printf("USB OTG pwr gpio request failed: %d\n", ret); + return ret; + } + + SETUP_IOMUX_PAD(PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL)); + SETUP_IOMUX_PAD(PAD_ENET_RX_ER__USB_OTG_ID | + MUX_PAD_CTRL(WEAK_PULLDOWN)); + clrbits_le32(&iomux->gpr[1], IOMUXC_GPR1_OTG_ID_MASK); + /* disable ext. charger detect, or it'll affect signal quality at dp. */ + return gpio_direction_output(SB_FX6_USB_OTG_PWR, 0); +} + +#define MX6_USBNC_BASEADDR 0x2184800 +#define USBNC_USB_H1_PWR_POL (1 << 9) +int board_ehci_hcd_init(int port) +{ + u32 *usbnc_usb_uh1_ctrl = (u32 *)(MX6_USBNC_BASEADDR + 4); + + switch (port) { + case 0: + return cm_fx6_init_usb_otg(); + case 1: + SETUP_IOMUX_PAD(PAD_GPIO_0__USB_H1_PWR | + MUX_PAD_CTRL(NO_PAD_CTRL)); + + /* Set PWR polarity to match power switch's enable polarity */ + setbits_le32(usbnc_usb_uh1_ctrl, USBNC_USB_H1_PWR_POL); + return cm_fx6_usb_hub_reset(); + default: + break; + } + + return 0; +} + +int board_ehci_power(int port, int on) +{ + if (port == 0) + return gpio_direction_output(SB_FX6_USB_OTG_PWR, on); + + return 0; +} +#endif + +#ifdef CONFIG_FEC_MXC +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS) + +static int mx6_rgmii_rework(struct phy_device *phydev) +{ + unsigned short val; + + /* Ar8031 phy SmartEEE feature cause link status generates glitch, + * which cause ethernet link down/up issue, so disable SmartEEE + */ + phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x3); + phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x805d); + phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4003); + val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe); + val &= ~(0x1 << 8); + phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val); + + /* To enable AR8031 ouput a 125MHz clk from CLK_25M */ + phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7); + phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016); + phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007); + + val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe); + val &= 0xffe3; + val |= 0x18; + phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val); + + /* introduce tx clock delay */ + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5); + val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e); + val |= 0x0100; + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val); + + return 0; +} + +int board_phy_config(struct phy_device *phydev) +{ + mx6_rgmii_rework(phydev); + + if (phydev->drv->config) + return phydev->drv->config(phydev); + + return 0; +} + +static iomux_v3_cfg_t const enet_pads[] = { + IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_GPIO_0__CCM_CLKO1 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_GPIO_3__CCM_CLKO2 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | MUX_PAD_CTRL(0x84)), + IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | + MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL | + MUX_PAD_CTRL(ENET_PAD_CTRL)), + IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL | + MUX_PAD_CTRL(ENET_PAD_CTRL)), +}; + +static int handle_mac_address(void) +{ + unsigned char enetaddr[6]; + int rc; + + rc = eth_getenv_enetaddr("ethaddr", enetaddr); + if (rc) + return 0; + + rc = cl_eeprom_read_mac_addr(enetaddr); + if (rc) + return rc; + + if (!is_valid_ether_addr(enetaddr)) + return -1; + + return eth_setenv_enetaddr("ethaddr", enetaddr); +} + +int board_eth_init(bd_t *bis) +{ + int res = handle_mac_address(); + if (res) + puts("No MAC address found\n"); + + SETUP_IOMUX_PADS(enet_pads); + /* phy reset */ + gpio_direction_output(CM_FX6_ENET_NRST, 0); + udelay(500); + gpio_set_value(CM_FX6_ENET_NRST, 1); + enable_enet_clk(1); + return cpu_eth_init(bis); +} +#endif + +#ifdef CONFIG_NAND_MXS +static iomux_v3_cfg_t const nand_pads[] = { + IOMUX_PADS(PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NO_PAD_CTRL)), + IOMUX_PADS(PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NO_PAD_CTRL)), +}; + +static void cm_fx6_setup_gpmi_nand(void) +{ + SETUP_IOMUX_PADS(nand_pads); + /* Enable clock roots */ + enable_usdhc_clk(1, 3); + enable_usdhc_clk(1, 4); + + setup_gpmi_io_clk(MXC_CCM_CS2CDR_ENFC_CLK_PODF(0xf) | + MXC_CCM_CS2CDR_ENFC_CLK_PRED(1) | + MXC_CCM_CS2CDR_ENFC_CLK_SEL(0)); +} +#else +static void cm_fx6_setup_gpmi_nand(void) {} +#endif + +#ifdef CONFIG_FSL_ESDHC +static struct fsl_esdhc_cfg usdhc_cfg[3] = { + {USDHC1_BASE_ADDR}, + {USDHC2_BASE_ADDR}, + {USDHC3_BASE_ADDR}, +}; + +static enum mxc_clock usdhc_clk[3] = { + MXC_ESDHC_CLK, + MXC_ESDHC2_CLK, + MXC_ESDHC3_CLK, +}; + +int board_mmc_init(bd_t *bis) +{ + int i; + + cm_fx6_set_usdhc_iomux(); + for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { + usdhc_cfg[i].sdhc_clk = mxc_get_clock(usdhc_clk[i]); + usdhc_cfg[i].max_bus_width = 4; + fsl_esdhc_initialize(bis, &usdhc_cfg[i]); + enable_usdhc_clk(1, i); + } + + return 0; +} +#endif + +#ifdef CONFIG_OF_BOARD_SETUP +void ft_board_setup(void *blob, bd_t *bd) +{ + uint8_t enetaddr[6]; + + /* MAC addr */ + if (eth_getenv_enetaddr("ethaddr", enetaddr)) { + fdt_find_and_setprop(blob, "/fec", "local-mac-address", + enetaddr, 6, 1); + } +} +#endif + +int board_init(void) +{ + gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; + cm_fx6_setup_gpmi_nand(); + cm_fx6_setup_i2c(); + + return 0; +} + +int checkboard(void) +{ + puts("Board: CM-FX6\n"); + return 0; +} + +void dram_init_banksize(void) +{ + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[1].start = PHYS_SDRAM_2; + + switch (gd->ram_size) { + case 0x10000000: /* DDR_16BIT_256MB */ + gd->bd->bi_dram[0].size = 0x10000000; + gd->bd->bi_dram[1].size = 0; + break; + case 0x20000000: /* DDR_32BIT_512MB */ + gd->bd->bi_dram[0].size = 0x20000000; + gd->bd->bi_dram[1].size = 0; + break; + case 0x40000000: + if (is_cpu_type(MXC_CPU_MX6SOLO)) { /* DDR_32BIT_1GB */ + gd->bd->bi_dram[0].size = 0x20000000; + gd->bd->bi_dram[1].size = 0x20000000; + } else { /* DDR_64BIT_1GB */ + gd->bd->bi_dram[0].size = 0x40000000; + gd->bd->bi_dram[1].size = 0; + } + break; + case 0x80000000: /* DDR_64BIT_2GB */ + gd->bd->bi_dram[0].size = 0x40000000; + gd->bd->bi_dram[1].size = 0x40000000; + break; + case 0xEFF00000: /* DDR_64BIT_4GB */ + gd->bd->bi_dram[0].size = 0x70000000; + gd->bd->bi_dram[1].size = 0x7FF00000; + break; + } +} + +int dram_init(void) +{ + gd->ram_size = imx_ddr_size(); + switch (gd->ram_size) { + case 0x10000000: + case 0x20000000: + case 0x40000000: + case 0x80000000: + break; + case 0xF0000000: + gd->ram_size -= 0x100000; + break; + default: + printf("ERROR: Unsupported DRAM size 0x%lx\n", gd->ram_size); + return -1; + } + + return 0; +} + +u32 get_board_rev(void) +{ + return cl_eeprom_get_board_rev(); +} + |
